Download pdf - HYUNDAI Genuine Accessories€¦ · HYUNDAI Genuine Accessories NO GOOD CLICK When disconnecting connectors, press the lock tab and pull apart by grasping the connectors. DO NOT PULL

HYUNDAI Genuine Accessories

Vehicle Model Elantra Accessory Interior Lighting Kit

Model Year 2017 ~ Difficulty ( B )

Basic Required Hand Tools

Instructional Symbols / Definitions

Difficulty stated above reflects the minimum level of expertise required to install

the accessory.

( A ) Customer ( B ) Dealer Technician ( C ) Master Technician

Note:

For SE models with Base Radio: Use Pin-8 and Pin-10 of the 16-Pin AUX Connector for the power connections.

Part No. F3068 ADU00

NOTE: THIS INTERIOR LIGHT KIT IS NOT APPLICABLE TO MANUAL TRANSMISSION, 1.4T ECO, OR SPORT ELANTRA MODELS.

- Accessory Installation

Ratchet 10mm Socket 13mm Socket Wire Cutters

Pliers Center PunchTorque Wrench

Electric Drill 19/32" Drill Bit#2 Phillips

Screwdriver

Nylon Trim Panel

Removal Tool

Tape Measure

Deburring Tool

3/16" Drill Bit Scissors

Denotes safety equipment required to be used such as a mask, safety glasses, gloves, and hearing protection.

Safety Glasses

Hearing Protection

Mask

Gloves

Denotes instructional steps necessary to complete the process.

Denotes quality processes to be checked prior to moving to the next step.

Denotes cautions to be taken to avoid physical injury or electronic component damage.

Denotes warnings that may lead to serious physical injury or vehicle damage.

Denotes specific tools that are necessary to complete the step.

Denotes cautions to be taken to avoid vehicle and component damage.

Notes to the Installer: 1) Read the entire installation instructions prior to beginning the installation of this accessory. 2) Make sure the vehicle is completely clean before the accessory is installed. 3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed. 4) To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet/mats. 5) Always wear appropriate safety gear to include gloves and safety glasses when required. 6) Factory wire colors are subject to change, please use the specified pin # in the harness connector to identify the correct wire for T-Tap installation.

FMVSS 110 Compliance Information

Part Number: F3068 ADU00

0.67 lbs 0.3 kg

(Gross Weight)

All dealers must determine if the weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories. Load Label Part Number:

NP070 - 09003

Elantra

Interior Lighting Kit

Revision Date

07/27/2016 Page 1 of 15

1 20 2 2

Description

LED & Bracket Assembly


Kit Overview

No. Qty.

LED

1 1

Wire Harness

2 1

Hardware Bag

4

3 1

5 1

Switch

6 1 Installation Instructions

Hardware Total

E

7 1

Hardware Overview

A C D

Plastic FastenerM8 x 1.5mm Flanged

Head NutWire Ties * T-Tap

25

* Extra components intentionally placed in kit as spares.

Please follow directions for proper placement of each component.

1

Glove Box Information Card

1

3

5 6 7 4

2

Elantra


Revision Date

07/27/2016 Page 2 of 15

Disconnecting Connectors Lock Connectors

When disconnecting connectors, grasp the connectors , not the wire When locking connectors, listen for a click indicating

they are securely locked.


NO GOOD

CLICK

When disconnecting connectors, press the lock tab and pull apart by grasping the connectors. DO NOT PULL ON WIRES.

Elantra


Revision Date

07/27/2016 Page 3 of 15

N

O

T

E

1. Continue to pull the Shift Knob up to remove the Shift Knob Assembly.

2. Store the Shift Knob Assembly in a safe location for reinstallation.N

O

T

E

1. Close the Forward Tray Cover.

2. Dislodge the Center Console Cover by gently pulling upwards to release

the four (4) pressure clips.

Caution: DO NOT scratch the Trim Panels or Shift Knob Assembly. Caution: DO NOT scratch the Trim Panels.

DO NOT lose the pressure clips.

3 Nylon Trim Panel Removal Tool 4

N

O

T

E

1. Park the vehicle on a level surface.

2. Apply the Parking Brake.

3. Move the Gear Selector from Park (P) position to Drive (D) position.

4. Record all pre-set radio stations (if applicable).

5. Disconnect and isolate the vehicle's Negative Battery Cable.

N

O

T

E

1. Carefully release the six (6) clips surrounding the Shifter Boot by

gently pulling the Shift Knob upwards.

WARNING! Shock Hazard. Do not touch vehicle's negative battery

terminal to vehicle's positive battery terminal. Serious physical injury

or vehicle damage may occur.

Caution: DO NOT scratch the Trim Panels or Shifter Boot.


Ratchet and 10mm Socket 1 2

Elantra


Revision Date

07/27/2016 Page 4 of 15


5 Nylon Trim Panel Removal Tool 6

N

O

T

E

1. Lift the Center Console Cover to access the Electrical Connectors.

2. Disconnect any Electrical Connectors and remove the Center Console

Cover from the vehicle.

3. Store the Center Console Cover in a safe location for reinstallation.

N

O

T

E

1. Remove the passenger side HVAC Close Out Panel by pressing the

three (3) tabs rearward.

2. Store the HVAC Close Out Panel in a safe location for reinstallation.

Caution: DO NOT scratch the Center Console Cover. Caution: DO NOT scratch the HVAC Close Out Panel or surrounding

Trim Panels.

#2 Phillips Screwdriver 7 8

N

O

T

E

1. In driver side footwell area, remove the one (1) plastic screw

and one (1) push clip as noted in step 8.

2. Route the Interior Light Wire Harness (Driver Side Label) through the

front left side of the Center Console, towards the Driver Side Footwell

area.

N

O

T

E

1. Pull the Interior Light Wire Harness (Driver Side Label) completely

through

to the Driver Side Footwell area as shown.

2. Pull the Harness, taking up all the slack.

3. Replace the one (1) plastic screw and one (1) push clip removed in

step 7.

Caution: Make sure not to route the Harness near any sharp edges. Caution: Make sure not to route the Harness near any sharp edges.

Plastic Screw

Interior Light Wire Harness Driver Side

HVAC Close Out Panel under Glove Box.

Elantra


Revision Date

07/27/2016 Page 5 of 15


9 Wire Cutters, Ratchet, 13mm Socket and Torque Wrench 10

N

O

T

E

1. Locate the unused M8 stud high up on the bulkhead, just below the

large factory wire harness.

2. Mount the driver side LED assembly, using one (1) M8 nut as shown.

Hand tighten only.N

O

T

E

1. Secure LED assembly to vehicle main harness, that passes through the

bulkhead grommet, using one (1) wire tie as shown.

2. Torque M8 Nut to 9.8 - 14.7 Nm (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft).

3. Trim excess wire tie material.

11 12

N

O

T

E

1. On driver's side, route harness up beside HVAC housing and secure

to side of housing with wire tie #1. Do not fully tighten wire tie.

2. Continue to route the harness up above the HVAC vent and secure with

wire tie #2 to factory HVAC damper actuator harness. Do not fully tighten

wire tie.

3. Route the harness down and secure with wire tie #3 to forward white

connector on MDPS module. Do not fully tighten wire tie.

N

O

T

E

1. Route the harness across the top of the MDPS module over towards the

fuse box area.

2. Secure the harness to the 2-Pin MDPS power and ground connector with

wire tie #4. Do not fully tighten wire tie.

3. Route the harness around the MDPS module and along the large factory

harness towards the LED/bulkhead, and secure with wire tie #5 and #6

as shown. Do not fully tighten wire ties.

Caution: Be sure not to route the Interior Light Harness near any sharp

edges.


edges.

Wire Tie

Factory Harness

M8 Nut

Large Factory Wire Harness

MDPS Module

Center Console Side Panel

Interior Light Wire Harness

HVAC Vent

Wire Tie #1

Wire Tie #2

Wire Tie #3

Wire Tie #4

Wire Tie #5

MDPS Module Bottom View


Wire Tie #6

Top View

Wire Tie #4

Steering Column

Bulkhead Grommet

Elantra


Revision Date

07/27/2016 Page 6 of 15


Wire Cutters 13 #2 Phillips Screwdriver 14

N

O

T

E

1. Finally, connect the harness to the LED.

2. Adjust slack in the harness to ensure it is routed evenly without

any tight or loose spots.

3. Once slack is adjusted, fully tighten all six (6) wire ties in the

driver side footwell area.


N

O

T

E

1. In passenger side footwell area, remove the one (1) plastic screw and

one (1) push clip.

2. Route the Harness (Passenger Side Label) through the front of the

Center Console towards the Passenger Side Footwell area as shown.


edges or where harness can be pinched.

Caution: Make sure not to route the Harness near any sharp edges.

15Scissors, Center Punch, Electric Drill, 3/16" Drill Bit and

Deburring Tool16

N

O

T

E

1. Pull the Harness (Passenger Side Label) completely through to the

Passenger Side Footwell area as shown.

2. Replace the one (1) plastic screw and one (1) push clip removed in

step 14.N

O

T

E

1. Using Scissors, cut out the Passenger Side LED Template from

the back of these installation instructions.

2. Remove the white sound insulation from the HVAC close out panel in

area shown above where template is positioned.

3. Place the Template on the HVAC Close Out Panel and mark the two (2)

Mounting Holes using a Center Punch.

4. Using an Electric Drill and 3/16" Drill Bit, drill the two (2) outer LED

Mounting Holes.

5. Deburr the two (2) holes using a deburring tool.

Caution: Make sure not to route the Harness near any sharp edges. Be careful not to enlarge the hole while drilling and deburring.

Mark and drill 3/16"

Plastic Screw and Push Clip


Wire Tie #6


LED

Wire Tie #4

Wire Tie #5

Passenger Side LED Template

Elantra


Revision Date

07/27/2016 Page 7 of 15


17 18

N

O

T

E

1. Install the LED onto the HVAC Close Out Panel as shown, using the

two (2) provided plastic fasteners.

2. Make sure the LED Connector Opening is facing towards the

front of the vehicle (bulkhead).

3. Reinstall the white sound insulation to the HVAC close out panel.

N

O

T

E

1. Connect the Interior Light Harness to the LED.

2. Adjust the Interior Light Harness to allow the HVAC Close Out Panel to

be lowered onto the floor carpet for service access.

Caution: Do not install HVAC close out panel yet. Image above shows

harness route for clarity.

Wire Cutters 19 Scissors, Center Punch, Electric Drill and 3/16" Drill Bit 20

N

O

T

E

1. Using one (1) wire tie, secure the Interior Light Harness to factory HVAC

connector as shown on passenger side footwell area.


3. Reinstall the HVAC Close Out Panel while tucking the Interior Light

Harness above the insulated pad area as noted in Step 16.

N

O

T

E

1. Using Scissors, cut out the Switch Template from the back

of these installation instructions.

2. Place the Template in the Center Console Cover and mark the

hole using a Center Punch as noted above.

3. Using an Electric Drill and 3/16" Drill bit, drill a pilot hole.

Caution: Be sure not to route Interior Light Harness near any sharp

edges.

Connector Opening Facing Bulkhead

Switch Template

Mark and drill 3/16"


Wire Tie

HVAC Factory Connector


Plastic Fasteners

Elantra


Revision Date

07/27/2016 Page 8 of 15

N

O

T

E

N

O

T

E

1. Using an Electric Drill and 19/32" Drill Bit, drill the hole in the

Center Console Cover.

2. Deburr the hole using a Deburring Tool.

Be careful not to enlarge the hole while drilling and deburring.

22

1. Insert the Switch into the hole.

- Make sure the Switch snaps in tightly and is oriented correctly as

shown.


Electric Drill, 19/32" Drill Bit and Deburring Tool 21

Pliers 23 Wire Cutters 24

N

O

T

E

1. At the Center Console area, locate the 12-Pin AUX Connector.

2. Connect one (1) T-Tap to the Blue Wire at Pin #4 as shown.

3. Connect one (1) T-Tap to the Gray Wire at Pin #6 as shown.

4. Connect the Blue Wire from the interior Light Harness to the T-Tap

at Pin #4.

5. Connect the Gray Wire from the interior Light Harness to the T-Tap

at Pin #6.

- Refer to the T-Tap Installation Procedure on page 3.

* For SE models with Base Radio: Locate the 16-Pin AUX Connector

and connect one (1) T-Tap to the Blue wire at Pin #8 and one (1)

T-Tap to the Gray wire at Pin #10.

N

O

T

E

1. Using one (1) wire tie, secure the Interior Light Harness as shown.


Caution: Be sure to install the T-Taps on the correct vehicle wires.

Make sure you connect the correct wire to the correct T-Tap. There

may be several wires of the same / similar color, please refer to Pin #

position identified on power connector.

Caution: Make sure not to route the Harness near any sharp edges.

Drill 19/32"

Pin #4 (Blue Wire)

Pin #6 (Gray Wire)

Wire Tie

Pin # 8 Blue Wire

Pin # 10 Grey Wire

16-Pin AUX Connector

12-Pin AUX Connector

Elantra


Revision Date

07/27/2016 Page 9 of 15

N

O

T

E

1. Connect the switch to the switch leg of the Interior Light Harness.

2. Using two (2) wire ties, secure the switch harness and Interior

Light Harness to the Factory Harness as shown above on the

console cover. If the vehicle application does not have the factory

harness, then secure the switch harness to the "L" shaped anchor clip

with one (1) wire tie as noted above.


4. Reinstall the Center Console Cover and Shift Knob assembly.

N

O

T

E

1. Place the Glove Box Information Card in the Glove Box.

2. Reconnect the vehicle's Negative Battery Cable and torque

to 5 Nm (0.5 kgf-m, 44.16 lb-in).

3. Move the Gear Selector from Drive (D) position to Park (P) position.

4. Program radio pre-sets recorded in step 1 (if applicable).

5. Perform the Function Check and Visual Check on the following page.

6. Installation is complete.

WARNING! Shock Hazard. Do not touch vehicle's negative battery

terminal to vehicle's positive battery terminal. Serious physical injury

or vehicle damage may occur.

Wire Cutters 27 Ratchet, 10mm Socket and Torque Wrench 28

N

O

T

E

1. Using one (1) wire tie, bundle the Switch Harness and secure to the

factory AUX/USB harness in the center console, as shown. Bundle

length should be about 15" (381mm).

2. Using one (1) wire tie, secure the driver side leg of the Interior Light

Harness in the center console, as shown


N

O

T

E

1. Using one (1) wire tie, secure the passenger side leg of the Interior Light

Harness in the center console, as shown.


Caution: Make sure not to route the Harness near any sharp edges. Caution: Be sure not to route interior light harness near any sharp

edges.


Wire Cutters and Tape Measure 25 Wire Cutters 26

Wire Tie

Wire Tie

Wire Harness

Wire Tie

Wire Harness

Wire Tie

Wire Tie

Switch Harness

Anchor Clip

Installed In Step 25

Installed In Step 25

Elantra


Revision Date

07/27/2016 Page 10 of 15

* NOTE: SE models with Base Radio have a 16-Pin AUX Connector. Unse Pin-8 and Pin-10 for power T-Taps.

Items To Be Checked Results Of The Check

Check the On / Off function of the Switch. Interior Lights should turn on and off when switch is in

the on position and headlamps are on.

Make sure to leave the interior light kit switch ON

after the Function Check is complete.

Visual Check

Item To Be Checked


Function Check

Items To Be Checked Results Of The Check

Check that the blue LED interior lights are illuminated

in Driver and Passenger side footwell areas when

both the vehicle headlamps and the On/Off switch

(installed with the kit) are on.

Interior lights should function with the headlamps on.

Check that the footwell light illumination changes

when using the vehicle Dimmer Switch.

Check that Blue LED Interior Lights are illuminated in

both Driver and Passenger side footwell areas.

Blue LED Interior Lights are illuminated.

Interior lights should become brighter and dimmer

when operating the vehicle Dimmer Switch.

Interior lights are in the ON position after the

Function Check is completed.

Blue LED interior lights not illuminated. Check:

- switch is in ON position.

- fuse is properly installed and intact.

- that T-Taps are installed on the correct wires*.

- spade terminals are installed correctly to the T-Taps.

- The LED's are connected to the interior light kit harness.

Issue / Concern

Troubleshooting

Blue LED interior lights do not operate with the vehicle

illumination circuit.

Check:



- that T-Taps are installed on the correct wires*.


Blue LED interior lights do not dim with vehicle

illumination circuit.

Check:



- that T-Taps are installed on the correct wires.


Elantra


Revision Date

07/27/2016 Page 11 of 15


Electrical Schematic

ILL +

ILL - Legend G - Gray Factory Wire B - Blue Factory Wire

- Wire T-Tap

ILL + Positive Illumination Circuit ILL - Negative Illumination Circuit

G

B

B

G

B

B

G

G

B

Interior Light Kit

Push Button Switch

LED Module LH

LED Module RH

1A Fuse

B

G

1A Fuse is located under

the Center Console Cover.

Elantra


Revision Date

07/27/2016 Page 12 of 15


Template - LED Passenger Side on

HVAC Close Out Panel

2 - 7/16"

3 - 13/16"

3 - 3/16"

5/8"

1 -

13

/16

" 2

- 5/8

"

NOTE: 1. Set printer scaling to “No Scaling” or “Actual Size” before printing template. The template will not print to scale if other settings are used. 2. After printing, use a ruler or tape measure to verify the dimensions shown on the template. 3. Once the dimensions are verified, cut the template out and continue with the installation.

1” Square

Elantra


Revision Date

07/27/2016 Page 13 of 15


This page intentionally left blank

Elantra


Revision Date

07/27/2016 Page 14 of 15


Template - Switch Location on

Center Console Cover Bin

NOTE: 1. Set printer scaling to “No Scaling” or “Actual Size” before printing template. The template will not print to scale if other settings are used. 2. After printing, use a ruler or tape measure to verify the dimensions shown on the template. 3. Once the dimensions are verified, cut the template out and continue with the installation.

Switch Template 1

- 9/1

6"

11

/16

"

1 - 9/16"

4 - 5/16"

Elantra


Revision Date

07/27/2016 Page 15 of 15