(800) 474-3267 | 1351 13th Ave S. Suite 130 Jacksonville Beach, FL 32250 | MoffittHVAC.com
FRP Louver FRP Louver
PANTHER series FRP Natural Ventilation
Ventilation's Natural Solution since 1961
FRP Louver fiberglass louver
Page 1 of 8
PANTHER series Page 1 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Louver Table of Contents
FRP Louvers Table of Contents ..................................................................................................................... 1
FRP Louver Product Details ........................................................................................................................... 2
FRP Adjustable Blade Louvers; 45° & 90° ..................................................................................................... 3
FRP Fixed Blade Louvers; 45° ........................................................................................................................ 4
FRP Fixed Blade Louvers; 45° cont. ............................................................................................................... 5
FRP Pictures .................................................................................................................................................. 6
FRP Adjustable Blade Louver Guide Specification ........................................................................................ 7
FRP Fixed Blade Louver Guide Specification ................................................................................................. 8
FRP Louver fiberglass louver
Page 2 of 8
PANTHER series Page 2 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Louver Product Details
STANDARD FEATURES
Construction: Hetron 99P ® polyester resin
with UV inhibitor, synthetic veil, Class 1
flame spread of 25 or less.
Minimum size: 12” wide x 24” high.
Maximum Size: 60” wide x 120” high.
Frame: 6” deep channel, 1/4” thick.
Blades: 1/8” thick, Center or end pivot.
Pivots and Bearings: Fiberglass Reinforced
Polypropylene.
Linkage: Fiberglass reinforced
polypropylene & FRP control arm.
Operating Range: Opens to 45°.
Dampers: Parallel Blade, Gravity Back draft
type.
OPTIONAL FEATURES
Dampers: Opposed Blade configurations
available.
Color: available on large orders.
Hardware:
o 316 SS
o Monel
Screen: 1/2” mesh Polyethylene Bird
screen, polyethylene insect screen, or
stainless steel screen.
Mullion covers for multiple installations.
Operating Range: Opens full 90°
Wall Mounting: Sleeves or Flanges
Operators:
o Manual locking hand quadrant
o Chain
o Motor
Mounting Clips or Fasteners
Capping Strips
Stop Pins.
PRODUCT DESCRIPTION
Moffitt Corporation Fiberglass Wall Louvers are fabricated for the rigors of industry. Designed to provide
maximum air flow at a minimum pressure drop and water entrainment. Offered in both stationary and
adjustable configurations, these fiberglass louvers are serviceable in hostile environments with excellent
chemical resistance, drainable blade designs and several mounting options.
FRP Louver fiberglass louver
Page 3 of 8
PANTHER series Page 3 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Adjustable Blade Louvers; 45° & 90°
STANDARD FEATURES:
1. Construction: Hetron 99P® polyester resin, class 1 flame spread of 25 or less,
UV inhibitor, synthetic veil
2. Frame: 6” deep channel, 1/4” thickness
3. Blades: “K” style, 1/8” thickness
4. Pivots: 5/8” dia. fiberglass reinforced
polypropylene
5. Operator: Manual locking quadrant
6. Bearings: Fiberglass reinforced
polypropylene
7. Linkage: Fiberglass reinforced
polypropylene brackets and FRP control
arm
8. Hardware: 304 stainless steel
9. Operating Range: 45°
10. Minimum Size: 12” wide x 24” high
11. Maximum Size: 60” wide x 120” high
12. Colors: Standard Gray
OPTIONAL FEATURES:
1. Color to Match: (Must meet quantity requirements)
2. Operating Range: Full 90°.
3. Off-center pivots prevent blade extension past front of
louver frame
4. Hardware: 316 stainless steel
5. Screen (Mounted on Rear of Louver): 1/2”
polyethylene mesh, 3/4” polyethylene mesh,
polyethylene insect screen, stainless steel
6. Mullion covers for multiple installations
7. Mounting clips and fasteners
8. Operator: Vinyl coated cable or electric motor
*NOTE: Opening size is normally 1/4”larger
than louver size. Structural support of louver
in opening by others. Screen adds
approximately 1/2” to depth
Frame Construction
FRP Louver fiberglass louver
Page 4 of 8
PANTHER series Page 4 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Fixed Blade Louvers; 45°
STANDARD FEATURES:
1. Construction: HETRON 99P® polyester resin,
class 1 flame spread of 25 or less, UV
inhibitor, synthetic veil
2. Frame: 6” deep channel, 1/4” thickness
3. Blades: “K” style, 1/8” thickness
4. Screen: 1/2” mesh 19 ga. galvanized
5. Minimum Size: 12” wide x 24” high
6. Maximum Size: 60” wide x 120” high
7. Colors: Standard Gray
OPTIONAL FEATURES:
1. Color to Match: (Must meet quantity
requirements)
2. Hardware: 316 stainless steel, Monel
3. Screen: 1/2” polyethylene mesh, 3/4”
polyethylene mesh, polyethylene insect screen, stainless steel
4. Mullion covers for multiple installations
5. Mounting clips and fasteners
Dimensions are out-to-out of frame and
include flanges
Width
Hei
ght
12 24 36 48 60
24 .413 .996 1.580 2.163 2.746
36 .826 1.993 3.160 4.326 5.493
48 1.240 2.990 4.740 6.490 8.240
60 1.650 3.986 6.319 8.653 10.986
72 2.066 4.983 7.899 10.816 13.733
84 2.479 5.979 9.479 12.979 16.479
96 2.892 6.976 11.059 15.142 19.226
108 3.306 7.927 12.639 17.306 21.972
120 3.719 8.968 14.218 19.498 24.718
“K” BLADE - 45°
To determine minimum free area
required for the louver:
1. Divide the required CFM flow
by the maximum recommended
free area velocity.
2. Select the most desirable
louver size from the free area
table that meets the minimum
free area requirement.
NOTE: Ratings do not include the
effect of bird screen.
*NOTE: Opening size is normally 1/4” larger than
louver size. Structural support of louver in opening by
others. Screen adds approximately 1/2” to depth.
FRP Louver fiberglass louver
Page 5 of 8
PANTHER series Page 5 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Fixed Blade Louvers; 45° cont.
Free Area Chart- Sq. Ft.
822 Beginning of Water Penetration
Free Area Velocity F.P.M. (Y)
Size
48"-48"
Wat
er
Pe
net
rati
on
oz.
per
Sq
. Ft.
(X
)
Fre
e A
rea
(15
min
. du
rati
on
)
Velocity thru Free Air (FPM)
Standard Air - .075 LB. per FT3
Pressure Drop
FRP Louver fiberglass louver
Page 6 of 8
PANTHER series Page 6 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Pictures
FRP Louver fiberglass louver
Page 7 of 8
PANTHER series Page 7 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Adjustable Blade Louver Guide Specification 1.1. DESCRIPTION
Furnish and Install Fiberglass 6” Adjustable Blade Louver and accessories as indicated on drawings.
1.2. QUALITY ASSURANCE MOFFITT (Jacksonville, FL, 1 800-474-3267) FRP Products establish the standard of quality required. Manufacturer and erector shall demonstrate a minimum of five (5) years of related industry experience.
1.3. SUBSTITUTIONS No substitutions will be considered unless written request for approval has been submitted by the bidder and has been received by the designer at least ten (10) days prior to bid date. Any proposed substitutions should meet the standards set by the specification.
1.4. SUBMITTALS Furnish approval drawings prior to fabrication and erection drawings prior to shipment showing all erection procedures and accessories required for the specified product.
2.1. CONSTRUCTION 2.1.1. Unit shall be constructed of isophalic polyester fire retardant resin equivalent to Hetron 99P® polyester resin with
a Class 1 flamespread of 25 or less. Ultraviolet inhibitors shall be incorporated into the resin. Louver sections shall include fiberglass unidirectional filaments and synthetic veil. Louver shall have a minimum of 40% glass by weight. Coloring shall be achieved by use of pigments impregnated through the entire profile.
2.1.2. Louver frames shall be 6" deep channel type and a minimum 1/4" thickness 2.1.3. Louver blades shall be "K" style design and a minimum 1/8" thickness, opening at 45°. 2.1.4. Louver bearings, pivots, linkages and brackets shall be fiberglass reinforced polypropylene. Control arms shall be
of fiberglass construction. 2.1.5. Louver blades shall operate by (fiberglass thumbscrew locking quadrant, pull cable operation, electric motor
operation). 2.1.6. Hardware shall be (304SS, 306SS, Monel).
2.2. OPTIONS/ACCESSORIES
Available accessories include: 1/2" mesh polypropylene bird screen mounted in removable PVC frame, SS screen, fiberglass mullion covers.
FRP Louver fiberglass louver
Page 8 of 8
PANTHER series Page 8 of 8 (800) 474-3267 | MoffittHVAC.com
FRP Fixed Blade Louver Guide Specification 1.1. DESCRIPTION
Furnish and Install Fiberglass 6” Stationary Blade Louver and accessories as indicated on drawings.
1.2. QUALITY ASSURANCE MOFFITT (Jacksonville, FL, 1 800-474-3267) FRP Products establish the standard of quality required. Manufacturer and erector shall demonstrate a minimum of five (5) years of related industry experience.
1.3. SUBSTITUTIONS No substitutions will be considered unless written request for approval has been submitted by the bidder and has been received by the designer at least ten (10) days prior to bid date. Any proposed substitutions should meet the standards set by the specification.
1.4. SUBMITTALS Furnish approval drawings prior to fabrication and erection drawings prior to shipment showing all erection procedures and accessories required for the specified product.
2.1. CONSTRUCTION 2.1.1. Unit shall be constructed of isophalic polyester fire retardant resin equivalent to Hetron 99P® polyester resin with
a Class 1 flamespread of 25 or less. Ultraviolet inhibitors shall be incorporated into the resin. Louver sections shall include fiberglass unidirectional filaments and synthetic veil. Louver shall have a minimum of 40% glass by weight. Coloring shall be achieved by use of pigments impregnated through the entire profile.
2.1.2. Louver frames shall be 6" deep channel type and a minimum 1/4" thickness 2.1.3. Louver blades shall be "K" style design and a minimum 1/8" thickness, opening at 45°. 2.1.4. Hardware shall be (304SS, 306SS, Monel).
2.2. OPTIONS/ACCESSORIES
Available accessories include: 1/2" mesh polypropylene bird screen mounted in removable PVC frame, SS screen, fiberglass mullion covers.