Download pdf - Ac Doc Sy Kit Sensoroptions 08 000

7/31/2019 Ac Doc Sy Kit Sensoroptions 08 000

1/13

Art.No.: AC-DOC_SY-KIT-SensorOptions_08-000 modified 01.04.2009

t

3:52.5 3:55.0 3:57.5 4:00.0 4:02.5 4:05.0 4:07.5 4:10.0

rp

m %

0

2

5

5

0

7

5

1

0

0

k

m

/h

0

2

5

5

0

7

5

1

0

0

1

2

5

1

5

0

1

7

5

2

0

0

2

2

5

1

:

4

2

.

6

0

Start


2/13

AC-DOC_SY-KIT-SensorOptions_08-000 page 2 / 13

Table of content

Table of content......................................................................................................................................................... 2

Preface ...................................................................................................................................................................... 3SYMBOLS USED IN THE TEXT...................................................................................................................3

1. Basic information of all modules and their features............................................................................................... 42. Available sensor options........................................................................................................................................ 5

2.1MOUNTING THE DIFFERENT SENSORS................................................................................................52.1.1 Mounting the front suspension sensor...................................................................................................... 5

2.1.2 Mounting the rear suspension sensor ...................................................................................................... 6

2.1.3 Mounting the brake pressure sensor ........................................................................................................ 7

2.2CONNECTING THE DIFFERENT SENSORS.............................................................................................82.2.1 Connecting the front suspension sensor................................................................................................... 8

2.2.2 Connecting the rear suspension sensor.................................................................................................... 8

2.2.3 Connecting the brake pressure sensor ..................................................................................................... 9

2.2.4 Connecting the 2D Laptime receiver ..................................................................................................... 10


3/13


Preface

This documentation contains the necessary information to setup and to work with the 2D kit system.

In order to achieve the optimum result when working with the 2D-Kit System, we recommend to read

the instructions carefully and follow them step by step.

Symbols used in the text

In the paragraphs highlighted with this symbol, you will find tips and practical advice to

work with the 2D-Kit System.

In the paragraphs highlighted with this symbol, you will find additional information and it is

very important that you follow the instructions given.

Documentation reference

The user get an unique item number for an user manual to find further assistance

Additional information about manuals, datasheets, software updates or new calculation

files can be downloaded from our homepage. The specific download area for the Kit

system can be found at: http://www.2d-kit-system.com (=>See Downloads)

Basic Kit

Sensor options

A/F (lambda) add-on Kit (4-stroke) with 1CH or 2CH

Deto add-on Kit (2-stroke)

Possible Updates

Kit software user manual (delivered with the CD: SW-CD RaceKIT)

2D Debus & DieboldMesysteme GmbHAlte Karlsruher Strae 876227 KarlsruheTel.: +49(0)721 94485-0Fax: +49(0)721 94485-29EMAIL: [email protected]: http://www.2D-Datarecording.comHomepage: http://www.2D-Kit-System.com
http://www.2d-kit-system.com/mailto:[email protected]://www.2d-datarecording.com/http://www.2d-kit-system.com/http://www.2d-kit-system.com/http://www.2d-datarecording.com/mailto:[email protected]://www.2d-kit-system.com/


4/13


1. Basic information of all modules and their features

SY-KITSusp_Bike-000: KIT suspension sensor add on:

This sensor package expands the system for full chassisrecording so good balance and drivability are no longermiracles. This sensor Kit comes with a 150mm and 75mmhigh end suspension travel sensor. This sensor kit allowsto analysing suspension travel and damper speed to set upyour bike suspension.

SY-KITPBrake-000: KIT brake pressure add on:Very small and lightweight 100 bar pressure sensor tomeasure front brake usage. The Sensor comes with an

adapter for easy fitting to the bike brake system. For propersuspension setup, the brake pressure sensor is a MUST,as braking influences the front fork setting most.

SY-KITSens_race-000: KIT sensor add on:Special Sensor package for racing application.Unlike the KITSusp_Bike and KITPBrake equivalents thesensors are not connected directly to the data logger but toa small, separate connection box. Connection andexchange of sensors is simplified.

This package includes a 150mm and a 75mm high-endsuspension travel sensor, 1 small and lightweight brakepressure sensor and a Box mini for the connection. Thissensor kit allows analyzing suspension travel, damperspeed and brake pressure to set up your bike suspensionmore properly.

SY-KIT_LR05-000: KIT Laptime Receiver:For higher precission in Laptime compared to the GPSLaptimeing the IR Laptrigger receiver is available. This

receiver will provide 0.0025 sec accuracy in Laptime.

AC-DOC_SY-KIT_IR-Laptriggerset-000

AC-KIT_LT05-000: Laptrigger transmitter KIT System:One IR Transmitter is needed on the Pit wall if you use theIR Laptrigger receiver.Only one IR Transmitter is needed per Racetrack.



5/13


2. Available sensor options

2.1 Mounting the different sensors

2.1.1 Mounting the front suspension sensor

The potentiometer has to be fitted parallel to the tubes of the fork to give correct values.

The maximum measure range of the used sensor must be equal or even longer than your

maximum suspension travel (150mm range is usual for front fork).

The picture above shows a clamp which is designed as a folding ring and offers an easy and parallelsensor support mounting.

Please check very carefully that neither the sensor nor the supports will limit the steering

angle or might get caught by any cable or line or damage them !!


6/13


2.1.2 Mounting the rear suspension sensor

To measure the suspension travel of the rear wing in some cases (for example R6) it is

impossible to mount the sensor directly parallel to the (standard) shock. So you have toput it somewhere between the rear frame and the wing. This causes big differences of

usable sensor measure length depending on the location of the of mounting. (50 mm or

75mm will work in most cases)

To avoid water entering the housing, please mount the grinder bar down below !

View of the rear suspension sensor (linear potentiometer 75mm),example mounted at a Yamaha R1

Also in this case please check very carefully that neither the sensor nor the supports

touch any moving parts or might block them. Check for maximal and minimal travel !


7/13


2.1.3 Mounting the brake pressure sensor

The picture below shows a possibility to fix the pressure sensor to the brake line system.

For this a special mounting kit is included in the sensor add-on kit, which fixes thepressure sensor with a double hollow screw to the main brake cylinder.


8/13


2.2 Connecting the different sensors

2.2.1 Connecting the front suspension sensor

The wires of both suspension sensors are delivered by 2D with the Tyco contact pins alreadycrimped. Just insert the individual contacts into the 34pin AMP connector. The following table givesyou the correct positions for the pins.

Technical information Interface unit (34pin AMP connector)

Cable length: 600mm (isolated) + 40mm (stripped PUR-cable)

Crimp contacts: Tyco crimp contacts

Susp_Front (white) Pin 10 >> see appendix

AGND (black) Pin 18 >> see appendix

+5V (red) Pin 26 >> see appendix

2.2.2 Connecting the rear suspension sensor




Susp_Rear (white) Pin 11 >> see appendix




9/13


2.2.3 Connecting the brake pressure sensor

The wires of the brake pressure sensor are delivered from 2D with the Tyco contact pins already

crimped. Just insert the individual contacts into the 34pin AMP connector. The following table givesyou the correct positions for the pins.



Crimp contacts: Tyco crimp contactsBrake pressure (white) Pin 4 >> see appendix




10/13


2.2.4 Connecting the 2D Laptime receiver

The wires of the laptime receiver are delivered by 2D with the Tyco contact pins already crimped.

Just insert the individual contacts into the 34pin AMP connector. The following table gives you thecorrect positions for the pins.




Signal (white) Pin 14 >> see appendix

DGND (black) Pin 22 >> see appendix


You will get a start-up reference for the IR laptrigger set (transmitter + receiver) at the 2D

KIT system website located in the download area. Take a look at



11/13


Required for:SY-KITSusp_Bike-000: KIT suspension sensor add onSY-KITSens_race-000: KIT sensor add on


12/13


Required for:SY-KITPBrake-000 : KIT brake pressure sensor add onSY-KITSens_race-000: KIT sensor add on


13/13


Required for:SY-KITLR05-000: KIT Laptime Receiver