Yamaha RX-V677 manual

Embed Size (px)

Citation preview

  • 8/21/2019 Yamaha RX-V677 manual

    1/146

    English

    AV Receiver

    Owner’s Manual

     Read the supplied booklet “Safety Brochure” before using the unit.

  • 8/21/2019 Yamaha RX-V677 manual

    2/146

  • 8/21/2019 Yamaha RX-V677 manual

    3/146

  • 8/21/2019 Yamaha RX-V677 manual

    4/146

  • 8/21/2019 Yamaha RX-V677 manual

    5/146

    Accessories En 5

    AccessoriesCheck that the following accessories are supplied with the product.

    Remote control   Batteries (AAA, R03, UM-4) (x2)

    AM antenna   FM antenna

    *One of the above is supplied depending on the region ofpurchase.

    YPAO microphone   Wireless antenna

    CD-ROM (Owner’s Manual)

    Easy Setup Guide

    Safety Brochure

    Insert the batteries the right

    way round.

    Operating range of the remote control

    • Point the remote control at the remote control sensor on the unit and remain within the operating rangeshown below.

    • The illustrations of the main unit and remote control used in this manual are of the RX-V777 (U.S.A.model), unless otherwise specified.

    • (RX-V777 [China, Korea, U.K. and Europe models] only)For information on how to control external devices with the remote control, refer to “Supplement forRemote Control” on the supplied CD-ROM.

    • Some features are not available in certain regions.

    • Due to product improvements, specifications and appearance are subject to change without notice.

    • This manual explains operations using the supplied remote control.

    • This manual describes all the “iPod”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod”, “iPhone”and “iPad”, unless otherwise specified.

    • indicates precautions for use of the unit and its feature limitations.

    • indicates supplementary explanations for better use.

    30° 30°

    Within6 m (20 ft)

    (RX-V777) (RX-V677)

    30° 30°

  • 8/21/2019 Yamaha RX-V677 manual

    6/146

    FEATURES   ➤ What you can do with the unit En 6

    FEATURES

    What you can do with the unit

    AV receiver (the unit)

    Speakers

    BD/DVD player

    HDMI Control

    Audio/Video

    TV remote control

    Audio

    HDMI Control

    Audio

    Audio/Video

    TV

    Sequential operation of a TV,AV receiver, and BD/DVD

    player (HDMI Control) 

    p.134

    Change the input sourceand favorite settings with

    one touch (SCENE) 

    p.51

    Supports 2- to 7.1-channel (plus presence)speaker system. Allows you to enjoy your favoriteacoustic spaces in various styles.

    Automatically optimizing the speakersettings to suit your room (YPAO)

     

    p.34

    • Reproducing stereo or multichannelsounds with the sound fields likeactual movie theaters and concert halls(CINEMA DSP)

     

    p.53

    • Enjoying compressed music withenhanced sound (Compressed MusicEnhancer)

     p.57

    • Playing back music in multiple rooms(multi-zone)

     

    p.78

    iPod/iPhone/iPad

    USB deviceAudio

    Network contents

    Wide variety of supported content

    • iPod/iPhone/iPad  p.63

    • USB  p.66

    • Media server (PC/NAS) 

    p.69

    • Internet radio 

    p.73• AirPlay

      p.76

    3D and 4K Ultra HDsignals supported

    Audio/Video(via HDMI/MHL)

    Smartphone/Tablet

    Control

    Control

  • 8/21/2019 Yamaha RX-V677 manual

    7/146

  • 8/21/2019 Yamaha RX-V677 manual

    8/146

    FEATURES   ➤ Part names and functions En 8

    Front panel (RX-V777)

    1MAIN ZONEz keyTurns on/off (standby) the unit.

    2 Standby indicatorLights up when the unit is in standby mode under any of thefollowing conditions.

    • HDMI Contorol is enabled (p.106)

    • Standby Through is enabled (p.107)

    • Network Standby is enabled (p.108)

    • An iPod is being charged (p.63)

    3 ZONE 2 keyEnables/disables the audio output to Zone2 (p.81).

    4 ZONE CONTROL keyChanges the zone (main zone or the Zone2) that is controlledby the keys and knobs on the front panel (p.81).

    5 INFO (WPS) keySelects the information displayed on the front display (p.86).

    Enters the wireless network connection setup (WPS pushbutton configuration) by holding down for 3 seconds (p.44).

    6MEMORY keyRegisters FM/AM radio stations as preset stations (p.59).

    7 PRESET keysSelect a preset FM/AM radio station (p.59).

    8 FM and AM keysSwitch between FM and AM (p.58).

    9 Front displayDisplays information (p.10).

    0 Remote control sensorReceives remote control signals (p.5).

    A TUNING keys

    Select the radio frequency (p.58).B PURE DIRECT key

    Enables/disables Pure Direct (p.57).

    C INPUT knobSelects an input source.

    D PHONES jack For connecting headphones.

    E YPAO MIC jack For connecting the supplied YPAO microphone (p.34).

    F TONE CONTROL keyAdjusts the high-frequency range and low-frequency rangeof output sounds (p.88).

    G SCENE keysSelect the registered input source, sound program, andvarious settings with one touch. Also, turns on the unit whenit is in standby mode (p.51).

    H PROGRAM keysSelect a sound program or a surround decoder (p.52).

    I STRAIGHT keyEnables/disables the straight decode mode (p.56).

    J VIDEO AUX (HDMI/MHL IN) jack For connecting a device, such as a camcorder and a gameconsole (p.28) or a smartphone (p.29).

    K USB jack For connecting a USB storage device (p.66) or an iPod(p.63).

    VIDEO jack For inputting video when “USB” is selected as the inputsource.

    L VOLUME knobAdjusts the volume.

    Part names and functions

    INFO(WPS)ZONE2 ZONECONTROL MEMORY PRESET   FM AM TUNING

    CONTROL

    TVBD

    DVD NET RADIO

    INPUT

    SCENE

    MAIN ZONE

    PHONES

    SILENT CINEMA

    STRAIGHT

    VIDEO

    PUREDIRECT

    HDMI/  5 V 2 .1 A

    VIDEO

    VOLUME

    AUXTONE   PROGRAM YPAO MIC

    M HL 5 V 1 A

    :9 B2 3 4 5 61   7 8 A

    C   LFED H I J KG

  • 8/21/2019 Yamaha RX-V677 manual

    9/146

    FEATURES   ➤ Part names and functions En 9

    Front panel (RX-V677)

    1MAIN ZONEz keyTurns on/off (standby) the unit.

    2 Standby indicatorLights up when the unit is in standby mode under any of thefollowing conditions.

    • HDMI Contorol is enabled (p.106)

    • Standby Through is enabled (p.107)

    • Network Standby is enabled (p.108)

    • An iPod is being charged (p.63)

    3 YPAO MIC jack For connecting the supplied YPAO microphone (p.34).

    4 ZONE 2 keyEnables/disables the audio output to Zone2 (p.81).

    5 Remote control sensorReceives remote control signals (p.5).

    6 ZONE CONTROL keyChanges the zone (main zone or the Zone2) that is controlledby the keys and knobs on the front panel (p.81).

    7 INFO (WPS) keySelects the information displayed on the front display (p.86).

    Enters the wireless network connection setup (WPS pushbutton configuration) by holding down for 3 seconds (p.44).

    8MEMORY keyRegisters FM/AM radio stations as preset stations (p.59).

    9 PRESET keysSelect a preset FM/AM radio station (p.59).

    0 FM and AM keysSwitch between FM and AM (p.58).

    A Front displayDisplays information (p.10).

    B TUNING keysSelect the radio frequency (p.58).

    C PURE DIRECT keyEnables/disables Pure Direct (p.57).

    D PHONES jack For connecting headphones.

    E INPUT keysSelect an input source.

    F TONE CONTROL keyAdjusts the high-frequency range and low-frequency rangeof output sounds (p.88).

    G SCENE keysSelect the registered input source, sound program, andvarious settings with one touch. Also, turns on the unit when

    it is in standby mode (p.51).

    H PROGRAM keysSelect a sound program or a surround decoder (p.52).

    I STRAIGHT keyEnables/disables the straight decode mode (p.56).

    J VIDEO AUX (HDMI/MHL IN) jack For connecting a device, such as a camcorder and a gameconsole (p.28) or a smartphone (p.29).

    K USB jack For connecting a USB storage device (p.66) or an iPod(p.63).

    VIDEO jack For inputting video when “USB” is selected as the inputsource.

    L VOLUME knobAdjusts the volume.

    INFO(WPS)ZONE2 ZONECONTROL MEMORY PRESET   FM AM TUNING

    CONTROL

    TVBD

    DVD   NET  RADIO

    SCENE

    MAIN ZONE

    PHONES

    SILENT  CINEMA

    STRAIGHT

    VIDEO

    PURE DIRECT

    VIDEO

    VOLUME

    AUXTONE   PROGRAM

     YPAO MIC

    INPUT

    HDMI/    5V 2.1AMHL 5V 1A

    5 A C3 4 6 7 81 2 9 :

    D   LF H I J KE G

    B

  • 8/21/2019 Yamaha RX-V677 manual

    10/146

    FEATURES   ➤ Part names and functions En 10

    Front display (indicators)

    1 ECOLights up when the unit is in the eco mode (p.113).

    2 HDMILights up when HDMI signals are being input or output.

    OUT1/OUT2 (RX-V777 only)Indicates the HDMI OUT jacks currently outputting an HDMIsignal

    OUT (RX-V677 only)Lights up when HDMI signals are being output.

    3 ENHANCERLights up when Compressed Music Enhancer (p.57) is

    working.

    4 CINEMA DSPLights up when CINEMA DSP or CINEMA DSP 3D (p.53) isworking.

    5 STEREOLights up when the unit is receiving a stereo FM radio signal.

    TUNEDLights up when the unit is receiving an FM/AM radio stationsignal.

    6 Signal strength indicatorIndicates the strength of the wireless network signal (p.42).

    7 PARTY (RX-V777 only)Lights up when the unit is in the party mode. (p.82)

    8 SLEEPLights up when the sleep timer is on.

    9 ZONE2Lights up when audio output to Zone2 is enabled (p.81).

    0MUTEBlinks when audio is muted.

    A Volume indicatorIndicates the current volume.

    B VIRTUALLights up when the Virtual Presence Speaker (VPS) (p.53) orthe virtual surround processing (p.55) is working.

    C Cursor indicatorsIndicate the remote control cursor keys currently operational.

    D Information displayDisplays the current status (such as input name and soundmode name). You can switch the information by pressingINFO (p.86).

    E ADAPTIVE DRCLights up when Adaptive DRC (p.88) is working.

    F Speaker indicatorsIndicate speaker terminals from which signals are output.

    A Front speaker (L)

    S Front speaker (R)D Center speaker

    F Surround speaker (L)G Surround speaker (R)H Surround back speaker (L)

    J Surround back speaker (R)K Surround back speakerB Presence speaker (L)

    N Presence speaker (R)

    L Subwoofer

    L C R   FPRFPL

    SL

    SBL SBRSB

    SW SR

    VOL.

    MUTE

    ADAPTIVE DRC VIRTUAL

    ENHANCER   TUNEDSTEREO

    2

    SLEEPPARTY

    ZONEOUT 1 2

    2 B3 4 7 8 :1 96 A5

    C CD E F

  • 8/21/2019 Yamaha RX-V677 manual

    11/146

    FEATURES   ➤ Part names and functions En 11

    Rear panel (RX-V777)

    1 REMOTE IN/OUT jacksFor connecting to an infrared signal receiver/emitter thatallows you to operate the unit and other devices from anotherroom (p.80).

    2 TRIGGER OUT jack For connecting to a device that supports the trigger function(p.32).

    3 DC OUT jack For connecting to an optional accessory.

    4 HDMI OUT 1–2 jacks

    For connecting to HDMI-compatible TVs and outputtingvideo/audio signals (p.23). When using ARC, TV audio signalcan also be input through the HDMI OUT 1 jack.

    5 ANTENNA jacksFor connecting to FM and AM antennas (p.29).

    6MONITOR OUT jacks

    COMPONENT VIDEO jacksFor connecting to a TV that supports component video andoutputting video signals (p.23).

    VIDEO jack For connecting to a TV that supports composite video andoutputting video signals (p.24).

    7 HDMI 1–5 jacksFor connecting to HDMI-compatible playback devices andinputting video/audio signals (p.25).

    8 SPEAKERS terminalsFor connecting to speakers (p.19).

    9 NETWORK jack For connecting to a network with a network cable (p.30).

    0WIRELESS jack For connecting the supplied wireless antenna (p.30).

    A VOLTAGE SELECTOR(General model only)Selects the switch position according to your local voltage(p.32).

    B Power cableFor connecting to an AC wall outlet (p.32).

    C PHONO jacks(Except for U.S.A. and Canada models)

    For connecting to a turntable (p.28).

    D AUDIO 1–2 jacksFor connecting to audio playback devices and inputtingaudio signals (p.28).

    E AV 1–6 jacksFor connecting to video/audio playback devices andinputting video/audio signals (p.25).

    F AV OUT jacksFor outputting video/audio to a recording device (such as aVCR) (p.31).

    G ZONE2 OUT jacksFor connecting to the external amplifier used in Zone2 andfor outputting audio (p.79).

    H PRE OUT jacks

    For connecting to a subwoofer with built-in amplifier or to anexternal power amplifier (p.31).

    AUDIO 1 AUDIO 2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV 1

    (TV)

    PBY PR

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)

    12

    ARC

    ANTENNA

    FMAM

    FRONT CENTER   SURROUND

    SINGLE

    SURROUNDBACK/BI-AMP

    SPEAKERS

    AV 5

    VIDEO

    AV 6 AV OUT ZONE OUT   SUBWOOFERSUR.BACKSURROUNDFRONT

    PRE OUT

    CENTER

    SINGLE

    ZONE 2

    NETWORKDC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A   (NET)

    12V

    IN

    OUT

    0.1A

    ZONE2/F.PRESENCE

    EXTRA SP

    COMPONENT VIDEO

    CENTER

    1

    2

    HDMI OUT

    (RADIO)

    WIRELESS

    2

    GD H

    8

    F

    71 3 4 9

    C

    A B0

    E

    65

    * The area around the video/audio output jacks ismarked in white on the actual product toprevent improper connections.

    (U.S.A. model)

  • 8/21/2019 Yamaha RX-V677 manual

    12/146

    FEATURES   ➤ Part names and functions En 12

    Rear panel (RX-V677)

    1 REMOTE IN/OUT jacksFor connecting to an infrared signal receiver/emitter that

    allows you to operate the unit and other devices from anotherroom (p.80).

    2 TRIGGER OUT jack For connecting to a device that supports the trigger function(p.32).

    3 DC OUT jack For connecting to an optional accessory.

    4 HDMI OUT jack 

    For connecting to an HDMI-compatible TV and outputtingvideo/audio signals (p.23). When using ARC, TV audio signalcan also be input through the HDMI OUT jack.

    5 ANTENNA jacksFor connecting to FM and AM antennas (p.29).

    6MONITOR OUT jacks

    COMPONENT VIDEO jacksFor connecting to a TV that supports component video andoutputting video signals (p.23).

    VIDEO jack For connecting to a TV that supports composite video andoutputting video signals (p.24).

    7 HDMI 1–5 jacksFor connecting to HDMI-compatible playback devices and

    inputting video/audio signals (p.25).

    8 SPEAKERS terminalsFor connecting to speakers (p.19).

    9 NETWORK jack For connecting to a network with a network cable (p.30).

    0WIRELESS jack For connecting the supplied wireless antenna (p.30).

    A VOLTAGE SELECTOR(General model only)

    Selects the switch position according to your local voltage(p.32).

    B Power cableFor connecting to an AC wall outlet (p.32).

    C AUDIO 1–2 jacksFor connecting to audio playback devices and inputtingaudio signals (p.28).

    D AV 1–6 jacksFor connecting to video/audio playback devices andinputting video/audio signals (p.25).

    E AV OUT jacksFor outputting video/audio to a recording device (such as a

    VCR) (p.31).

    F ZONE2 OUT jacksFor connecting to the external amplifier used in Zone2 andfor outputting audio (p.79).

    G SUBWOOFER PRE OUT 1–2 jacksFor connecting to a subwoofer with built-in amplifier (p.31).

    AUDIO 1 AUDIO 2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV 1

    (TV)

    PBY PR

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI OUT

    ARC

    ANTENNA(RADIO)

    FMAM

    FRONT CENTER   SURROUND

    SINGLE

    SURROUNDBACK/BI-AMP

    SPEAKERS

    AV 5 AV 6 AV OUT ZONE OUTSUBWOOFERPRE OUT

    ZONE 2

    NETWORKDC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A   (NET)

    12V

    IN

    OUT

    0.1A

    ZONE2/F.PRESENCE

    EXTRA SP

    COMPONENT VIDEO

    HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)

    VIDEO

    1

    2

    WIRELESS

    2

    F GC

    8

    E

    71 3 4 9   A B

    D

    5 6 0

    * The area around the video/audio output jacks ismarked in white on the actual product to preventimproper connections.

    (U.S.A. model)

  • 8/21/2019 Yamaha RX-V677 manual

    13/146

  • 8/21/2019 Yamaha RX-V677 manual

    14/146

    PREPARATIONS   ➤ General setup procedure En 14

    PREPARATIONS

    This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!

    General setup procedure

    1 Placing speakers (p.15) Select the speaker layout for the number of speakers that you are using and place them in your room.

    2 Connecting speakers (p.19) Connect the speakers to the unit.

    3 Connecting a TV (p.23) Connect a TV to the unit.

    4 Connecting playback devices (p.25) Connect video devices (such as BD/DVD players) and audio devices (such as CD players) to the unit.

    5 Connecting the FM/AM antennas (p.29) Connect the supplied FM/AM antennas to the unit.

    6Connecting a network cable or thewireless antenna (p.30)

    Connect the unit to a router (access point) with a network cable, or connect the supplied wireless antenna

    for establishing a wireless network connection.

    7 Connecting other devices (p.31) Connect external devices, such as an external power amplifier (RX-V777 only) and recording devices.

    8 Connecting the power cable (p.32) After all the connections are complete, plug in the power cable.

    9Selecting an on-screen menu language

    (p.33)Select the desired on-screen menu language (default: English).

    10Optimizing the speaker settingsautomatically (YPAO) (p.34)

    Optimize the speaker settings, such as volume balance and acoustic parameters, to suit your room

    (YPAO).

    11Connecting to a network device wirelessly(p.42)

    Connect the unit to a wireless router (access point) or a mobile device by establishing a wireless

    connection.

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    15/146

    PREPARATIONS   ➤ Placing speakers En 15

    Select the speaker layout for the number of speakers that you are using and place the speakers and subwoofer (with built-in amplifier) in your room. This section describes the

    representative speaker layout examples.

    If you use five speakers in the front side, use two of them as front surround speakers (*1) or presence speakers (*2). We recommend using them as front surround speakers forenjoying unprocessed playback (p.56) or presence speakers for enjoying stereoscopic sound fields (p.53).

    • For information on the ideal speaker layout, see “Ideal speaker layout” (p.128).

    • If you have seven speakers, use two of them as surround back speakers or presence speakers.To reinforce the rear left/right sounds, use them as surround back speakers.To create a natural 3-dimensional sound field, use them as presence speakers.

    • Two subwoofers connected to the unit output the same sounds.

    1 Placing speakers

    Caution

    • Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 MIN”. In this case, you can also use 4-ohm speakers as the front speakers.For details, see “Setting the speaker impedance” (p.18).

    Speaker type Abbr. Function

    Speaker system (the number of channels)

    7.1+2 7.1 7.1 6.1 5.1Front

    5.14.1 3.1 2.1

    Front (L) 1Produce front left/right channel sounds (stereo sounds).

    ● ● ● ● ● ● ● ● ●

    Front (R) 2   ● ● ● ● ● ● ● ● ●

    Center 3 Produces center channel sounds (such as movie dialogue and vocals).   ● ● ● ● ● ● ●

    Surround (L) 4Produce surround left/right channel sounds. Surround speakers also produce surround back channelsounds when no surround back speakers are connected.

    ● ● ● ● ●   *1 ●

    Surround (R) 5   ● ● ● ● ●   *1 ●

    Surround back (L) 6Produce surround back left/right channel sounds.

    ● ●

    Surround back (R) 7   ● ●

    Surround back 8 Produces sounds mixed from surround back left/right channel sounds.   ●

    Presence (L) EProduce CINEMA DSP effect sounds. In combination with CINEMA DSP 3D (p.53), the presence speakerscreate a natural 3-dimensional sound field in your room.

    ● ●   *2

    Presence (R) R   ● ●   *2

    Subwoofer 9Produces LFE (low-frequency effect) channel sounds and reinforces the bass parts of other channels.

    This channel is counted as “0.1”. You can connect 2 subwoofers (with built-in amplifier) to the unit.  ● ● ● ● ● ● ● ● ●

    1 2 3 4 5 6 7 8 9 10 11

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    16/146

    PREPARATIONS   ➤ Placing speakers En 16

    7.1+2-channel system

    • The surround back speakers and presence speakers do not produce sounds simultaneously. The unitautomatically changes the speakers to be used, depending on the selected CINEMA DSP (p.53).

    7.1-channel system (using presence speakers)

    This speaker system uses the front presence speakers to produce a natural

    3-dimensional sound field, and is suited for enjoying 5.1-channel contents.

    7.1-channel system (using surround back speakers)

    This speaker system creates Virtual Presence Speaker (VPS) using the front, center and

    surround speakers to produce a 3-dimensional sound field, and also allows you to

    enjoy extended surround sounds using the surround back speakers.

    6.1-channel system

    This speaker system creates Virtual Presence Speaker (VPS) using the front, center and

    surround speakers to produce a 3-dimensional sound field, and also allows you to

    enjoy extended surround sounds using the surround back speaker.

    4 5

    1   2

    39

    6 7

    E R

    9

    4 5

    1   2

    39

    E R

    4 5

    1   2

    39

    6 7

    4 5

    1   2

    39

    8

    1 2 3 4 5 6 7 8 9 10 11

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    17/146

    PREPARATIONS   ➤ Placing speakers En 17

    5.1-channel system

    This speaker system creates Virtual Presence Speaker (VPS) using the front, center and

    surround speakers to produce a 3-dimensional sound field, and is suited for enjoying

    5.1-channel contents.

    Front 5.1-channel system (using surround speakers)

    Even when surround speakers are placed in the front side, the unit creates the virtual

    surround speakers in the rear side to allow you to enjoy multi-channel surround sound (Virtual

    CINEMA FRONT) when “Layout (Surround)” (p.101) in the “Setup” menu is set to “Front”.

    • You can enjoy surround sound even without the center speaker (front 4.1-channel system).

    Front 5.1-channel system (using presence speakers)

    This speaker system uses the front presence speakers to produce a natural

    3-dimensional sound field, and creates the virtual surround speakers using the front

    speakers to allow you to enjoy multi-channel surround sound (Virtual CINEMA DSP).

    4.1-channel system

    4 5

    1 2

    39

    4 5

    1 2

    39

    1   2

    39

    E R

    4 5

    1 2

    9

    1 2 3 4 5 6 7 8 9 10 11

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    18/146

    PREPARATIONS   ➤ Placing speakers En 18

    2.1-channel system

    Even when no surround speakers are connected, the unit creates the virtual surround

    speakers using the front speakers to allow you to enjoy multi-channel surround sound

    (Virtual CINEMA DSP).

    • Add the center speaker to configure a 3.1-channel system.

    ■ Setting the speaker impedanceUnder its default settings, the unit is configured for 8-ohm speakers. When using a

    6-ohm speaker for any channel, set the speaker impedance to “6  MIN”. In this case,

    you can also use 4-ohm speakers as the front speakers.

    1 Before connecting speakers, connect the power cable to an AC walloutlet.

    2 While holding down STRAIGHT on the front panel, pressMAIN ZONEz.

    3 Check that “SP IMP.” is displayed on the front display.

    4 Press STRAIGHT to select “6  MIN”.

    5 Press MAIN ZONEz to set the unit to standby mode and remove thepower cable from the AC wall outlet.

    You are now ready to connect the speakers.

    1 2

    9

    MAIN ZONEz

    STRAIGHT

    SP IMP. 8 MIN

    1 2 3 4 5 6 7 8 9 10 11

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    19/146

    PREPARATIONS   ➤ Connecting speakers En 19

    Connect the speakers placed in your room to the unit.

    The following diagrams provide connections for 7.1+2-,

    7.1-, and 6.1-channel systems as examples. For othersystems, connect speakers while referring to the

    connection diagram for the 6.1-channel system.

    Cables required for connection

    (commercially available)

    Speaker cables (x the number of speakers)

    Audio pin cable (two for connecting two subwoofers)

    7.1+2-channel system 7.1-channel system

    (using surround back speakers)

    2 Connecting speakers

    Caution

    • Remove the unit’s power cable from an AC wall outlet and turnoff the subwoofer before connecting the speakers.

    • Ensure that the core wires of the speaker cable do not touchone another or come into contact with the unit’s metal parts.Doing so may damage the unit or the speakers. If the speaker

    cables short circuit, “Check SP Wires” will appear on the frontdisplay when the unit is turned on.

    • The illustrations of the unit (rear) used in this section are of theRX-V777.

    +

    +

    FRONT CENTER   SURROUND

    SINGLE

    SURROUND BACK/BI-AMP

    SPEAKERS

    ZONE2/F.PRESENCE

    EXTRA SP

    1

    2

    1

    6 7

    2

    3

    4 5

    9 9

    E R

    The unit (rear)

    FRONT CENTER   SURROUND

    SINGLE

    SURROUND BACK/BI-AMP

    SPEAKERS

    ZONE2/F.PRESENCE

    EXTRA SP

    1

    2

    1

    6 7

    2

    3

    4 5

    9

    The unit (rear)

    1 2 3 4 5 6 7 8 9 10 11

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    20/146

    PREPARATIONS   ➤ Connecting speakers En 20

    7.1-channel system(using presence speakers)

    6.1-channel system   ■ Connecting speaker cablesSpeaker cables have two wires. One is for connecting

    the negative (-) terminal of the unit and the speaker, and

    the other is for the positive (+) terminal. If the wires are

    colored to prevent confusion, connect the black wire tothe negative and the other wire to the positive terminal.

    a Remove approximately 10 mm (3/8”) of insulation from

    the ends of the speaker cable and twist the bare wires of

    the cable firmly together.

    b Loosen the speaker terminal.

    c Insert the bare wires of the cable into the gap on the side

    (upper right or bottom left) of the terminal.

    d Tighten the terminal.

    Using a banana plug

    (U.S.A., Canada, China, Australia and General models only)

    a Tighten the speaker terminal.

    b Insert a banana plug into the end of the terminal.

    FRONT CENTER   SURROUND

    SINGLE

    SURROUND BACK/BI-AMP

    SPEAKERS

    ZONE2/F.PRESENCE

    EXTRA SP

    1

    2

    1 2

    3

    4 5

    9

    E R

    The unit (rear)

    FRONT CENTER   SURROUND

    SINGLE

    SURROUND BACK/BI-AMP

    SPEAKERS

    ZONE2/F.PRESENCE

    EXTRA SP

    1

    2

    1 2

    3

    4 5

    9

    8

    When using only one surround back speaker, connect it

    to the SINGLE jack (L side).

    The unit (rear)

    FRONT

    aa

    b

    d

    c+ (red)

    - (black)

    FRONTa

    b

    Banana plug

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    21/146

    PREPARATIONS   ➤ Connecting speakers En 21

    Push-type speaker terminals

    (RX-V677 only)

    a Remove approximately 10 mm (3/8”) of insulation from

    the ends of the speaker cable, and twist the bare wires of

    the cable firmly together.

    b Press down the tab.

    c Insert the bare wires of the cable into the hole in the

    terminal.

    d Release the tab.

    ■ Connecting the subwooferUse an audio pin cable to connect the subwoofer.

    Connecting front speakers thatsupport bi-amp connections

    When using front speakers that support bi-amp

    connections, connect them to the FRONT jacks and

    SURROUND BACK/BI-AMP jacks.

    To enable the bi-amp function, set “Power Amp Assign”

    (p.100) in the “Setup” menu to “5ch BI-AMP” after

    connecting the power cable to an AC wall outlet.

    • The FRONT jacks and SURROUND BACK/BI-AMP jacks output thesame signals.

    ONE 2 / F.PRESENCE

    TRA SP

    aa b

    c

    d + (red)

    - (black)

    Audio pin cable

    1 2

    3

    4 5

    9

    FRONT CENTER   SURROUND

    SINGLE

    SURROUND BACK/BI-AMP

    SPEAKERS

    ZONE2/F.PRESENCE

    EXTRA SP

    1

    2

    The unit (rear)

    Caution

    • Before making bi-amp connections, remove any brackets orcables that connect a woofer with a tweeter. Refer to theinstruction manual of the speakers for details. If you are notmaking bi-amp connections, make sure that the brackets or

    cables are connected before connecting the speaker cables.• Surround back speakers cannot be used during bi-amp

    connections.

  • 8/21/2019 Yamaha RX-V677 manual

    22/146

    PREPARATIONS   ➤ Input/output jacks and cables En 22

    ■ Video/audio jacks

    ❑ HDMI jacks

    Transmit digital video and digital sound through a single

    jack. Use an HDMI cable.

    • Use a 19-pin HDMI cable with the HDMI logo. We recommend usinga cable less than 5.0 m (16.4 ft) long to prevent signal qualitydegradation.

    • The unit’s HDMI jacks support the HDMI Control, Audio ReturnChannel (ARC), and 3D and 4K Ultra HD video transmissionfeatures.

    • Use high speed HDMI cables to enjoy 3D or 4K Ultra HD videos.

    ❑ HDMI/MHL jack 

    Transmits digital video and digital sound. Use an MHL

    or HDMI cable.

    • The VIDEO AUX jack on the front panel of the unit supports bothMHL and HDMI connections. Use a cable that matches the jack onyour MHL-compatible mobile device. For details on an MHLconnection, see “MHL connection” (p.29). When connecting anHDMI-compatible playback device to the VIDEO AUX jack, use anHDMI cable.

    ■ Video jacks

    ❑ COMPONENT VIDEO jacks

    Transmit video signals separated into three

    components: luminance (Y), chrominance blue (PB),

    and chrominance red (PR). Use a component video

    cable with three plugs.

    ❑ VIDEO jacks

    Transmit analog video signals. Use a video pin cable.

    ■ Audio jacks

    ❑ OPTICAL jacks

    Transmit digital audio signals. Use a digital optical

    cable. Remove the tip protector (if available) before

    using the cable.

    ❑ COAXIAL jacks

    Transmit digital audio signals. Use a digital coaxial

    cable.

    ❑ AUDIO jacks

    Transmit analog stereo audio signals. Use a stereo pin

    cable (RCA cable).

    Input/output jacks and cables

    HDMI cable

    MHL or HDMI cable

    OR OUT

    Component video cable

    Video pin cable

    OPTICAL

    Digital optical cable

    COAXIAL

    Digital coaxial cable

    Stereo pin cable

  • 8/21/2019 Yamaha RX-V677 manual

    23/146

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    24/146

    PREPARATIONS   ➤ Connecting a TV En 24

    ❑ VIDEO (composite video) connection (with a video pin cable)

    ■ Connecting another TV or a projector(RX-V777 only)

    The unit has two HDMI output jacks. If you connect another TV or a projector to the unit

    with an HDMI cable, you can switch the TV (or projector) to be used for watching

    videos with the remote control (p.50).

    • HDMI Control is not available on the HDMI OUT 2 jack.

    A UD IO 1 A UD IO 2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI 1 HDMI 2 HDMI 3(BD/DVD)

    12

    ARC

    ANTENNA

    FMAM

    AV5

    VIDEO

    AV6 AVOUT ZONE OUTSUFRONTZONE 2

    DC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    HDMI OUT

    (RADIO)

    VIDEOVIDEO

    MONITOR

    V V

    OPTICAL

    O

    O

    OPTICAL

    AV4

    (TV)

    The unit (rear)MONITOR OUT

    (VIDEO) jackVideo input

    (composite video)

    AV 4 (OPTICAL) jack Audio output(digital optical)

    TV

    AUDIO1 AUDIO2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    VIDE

    MO

    HDMI 1 HDMI 2(BD/DVD)

    12

    ARC

    ANTENNA

    FMAM

    AV5

    VIDEO

    AV6 AVOUT ZONEZONE

    DC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    HDMI OUT

    (RADIO)

    HDMI

    HDMI

    2 1

    OUT

    ARC

    HDMI

    H D MI    

    The unit (rear)

    HDMI OUT 2 jack

    HDMI input

    Projector

    TV (already connected)

    TV

  • 8/21/2019 Yamaha RX-V677 manual

    25/146

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    26/146

    PREPARATIONS   ➤ Connecting playback devices En 26

    ■ Composite video connectionConnect a video device to the unit with a video pin cable and an audio cable (digital

    coaxial, digital optical, or stereo pin cable). Choose a set of input jacks (on the unit)

    depending on the audio output jacks available on your video device.

    If you select the input source by pressing AV 3–6, the video/audio played back on the

    video device will be output from the unit.

    • To watch videos input to the AV 3–6 (VIDEO) jacks, you need to connect your TV to the HDMI OUT jack(p.23) or to the MONITOR OUT (VIDEO) jack (p.24) of the unit. For details, refer to “Video signal flow”(p.133).

    ■ Changing the combination of video/audio input jacksIf the combination of video/audio input jacks available on the unit does not match your

    video device, change its combination according to the output jacks of your device. You

    can connect a video device that has the following video/audio output jacks.

    ❑ Necessary setting

    For example, if you have connected a video device to AV 2 (COMPONENT VIDEO) and

    AV 5 (AUDIO) jacks of the unit, change the combination setting as follows.

    Output jacks on video deviceInput jacks on the unit

    Video Audio

    Composite video

    Digital coaxial AV 3 (VIDEO + COAXIAL)

    Digital optical AV 4 (VIDEO + OPTICAL)

    Analog stereo AV 5–6 (VIDEO + AUDIO)

    AUDIO1 AUDIO2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    HDMI 1(BD/DVD)

    12

    ARC

    AN

    AM

    AV5

    VIDEO

    AV6 A

    DC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    HDMI OUT

    (R

    R

    L

    COAXIAL

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    VIDEO

    C C

    L

    R

    L

    R

    O O

    V

    V

    The unit (rear)

    AV 3–6 (VIDEO) jack

    Video output

    (composite video)

    Video device

    Audio output(either digital optical,

    digital coaxial, or analog stereo)

    Any of AV 3 (COAXIAL) jack,AV 4 (OPTICAL) jack,AV 5–6 (AUDIO) jacks

    Output jacks on video device Input jacks on the unit

    Video Audio Video Audio

    HDMI

    Digital optical HDMI 1–5AV 1 (OPTICAL)

    AV 4 (OPTICAL)

    Digital coaxial HDMI 1–5 AV 2–3 (COAXIAL)

    Analog stereo HDMI 1–5AV 5–6 (AUDIO)

    AUDIO 1–2

    Component video Analog stereoAV 1–2

    (COMPONENTVIDEO)

    AV 5–6 (AUDIO)

    AUDIO 1–2

    A UD IO 1 A UD IO 2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    HDMI 1(BD/DVD)

    12

    ARC

    ANTEN

    AM

    AV5

    VIDEO

    AV6 AVO

    DC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    HDMI OUT

    (RADIO

    AV 5

    R

    LAUDIO

    AV2

    PBY   PR

    L

    R

    L

    R

    PR

    PB

    Y

    COMPONENTVIDEO

    PR

    PB

    Y

    PR

    PB

    Y

    AV 2 (COMPONENT VIDEO) jacks

    Video output(component video)

    AV 5 (AUDIO) jacks

    Video device

    Audio output(analog stereo)

    The unit (rear)

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    27/146

    PREPARATIONS   ➤ Connecting playback devices En 27

    • The following operation is available only when your TV is connected to the unit via HDMI.

    1 After connecting external devices (such as a TV and playbackdevices) and power cable of the unit, turn on the unit.

    2 Press AV 2 to select “AV 2” (video input jack to be used) as the inputsource.

    3 Press ON SCREEN.

    4 Use the cursor keys to select “Input” and press ENTER.5 Use the cursor keys (e / r) to select “AV2” (video input jack to be

    used) and press the cursor key (q).

    6 Use the cursor keys to select “Audio In” and press ENTER.

    7 Use the cursor keys to select “AV5” (audio input jack to be used).

    8 Press ON SCREEN.This completes the necessary settings.

    If you select “AV 2” as the input source by pressing AV 2, the video/audio played back

    on the video device will be output from the unit.DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

      POP-UP/MENU

    ISPLAYRETURN

      - / 

    TUNER   USB

    AV

    AUDIO

    5

    65

    V-AUX

    1 2

    1 2

    3 4

    SB

    AUDIO

    5

    -

    1

    1 2

    3 4

    ON SCREEN

    ENTER

    AV 2

    Cursor keys

  • 8/21/2019 Yamaha RX-V677 manual

    28/146

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    29/146

    PREPARATIONS   ➤ Connecting the FM/AM antennas En 29

    ❑ MHL connection

    Connect an MHL-compatible mobile device (such as smartphones) to the unit with an

    MHL cable. You can enjoy full HD videos and multichannel audio sources stored on the

    mobile device. The VIDEO AUX jack of the unit enables you to input videos and audio

    directly from the mobile device to the unit.

    If you select “V-AUX” as the input source by pressing V-AUX, the video/audio playedback on the mobile device will be output from the unit.

    • To watch videos input to the VIDEO AUX jack, you need to connect your TV to the HDMI OUT jack of theunit (p.23).

    • You need to prepare an MHL cable that match the jack on your mobile device.

    • You can operate the mobile device using the menu operation keys, external device operation keys andnumeric keys on the remote control. However, some features may not be compatible, depending on themobile device or its application. In this case, operate the mobile device itself.

    • If “Standby Through” (p.107) in the “Setup” menu is set to “On”, you can output mobile device videos/audioto the TV or operate the mobile device using the remote control of the unit even when the unit is in standbymode.

    • The unit supplies power to the mobile device in the following conditions.

    – The unit is turned on.

    – The unit is in standby mode while “Standby Through” (p.107) in the “Setup” menu is set to “On”.

    Connect the supplied FM/AM antennas to the unit.

    Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.

    Assembling and connecting the AM antenna

    • Unwind only the length of cable needed from the AM antenna unit.

    • The wires of the AM antenna have no polarity.

    CONTROL

    TVBD

    DVD NET RADIO

    PHONES

    SILENT CINEMA

    STRAIGHT

    VIDEOHDMI/  5 V 2 .1 A

    VIDEO AUXTONE   PROGRAM YPAO MIC

    M HL 5 V 1 A

    MHL

    MHL

    Mobile device

    MHL output

    The unit (front)

    5 Connecting the FM/AM antennas

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)

    12

    ARC

    ANTENNA

    FMAM

    FRONT CENTER   SURROUND

    SPEAKERS

    VIDEO

    CENTER

    NETWORKDC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A   (NET)

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    CENTER

    HDMI OUT

    (RADIO)

    FM antenna

    AM antenna

    The unit (rear)

    Hold down Insert Release

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    30/146

    PREPARATIONS   ➤ Connecting a network cable or the wireless antenna En 30

    Connect the unit to a router (access point) with a network cable, or connect the

    supplied wireless antenna for establishing a wireless network connection.

    You can enjoy Internet radio or music files stored on media servers, such as PCs andNetwork Attached Storage (NAS), on the unit.

    Connecting the network cable

    Connect the unit to your router with a commercially-available STP network cable (CAT-5

    or higher straight cable).

    • If you are using a router that supports DHCP, you do not need to configure any network settings for the unit,as the network parameters (such as the IP address) will be assigned automatically to it. You only need toconfigure the network settings if your router does not support DHCP or if you want to configure the networkparameters manually (p.107).

    • You can check whether the network parameters (such as IP address) are properly assigned to the unit in“Network” (p.115) in the “Information” menu.

    • Some security software installed on your PC or the firewall settings of network devices (such as a router)may block the access of the unit to the network devices or the Internet. In these cases, configure thesecurity software or firewall settings appropriately.

    • Each server must be connected to the same subnet as the unit.

    • To use the service via the Internet, broadband connection is strongly recommended.

    Connecting the wireless antenna

    Connect the supplied wireless antenna to the unit for establishing a wireless networkconnection.

    For information on how to connect the unit to a network device wirelessly, see

    “Connecting to a network device wirelessly” (p.42).

    a Rotate the antenna clockwise.

    b Stand the antenna up straight.

    • Do not connect the antenna other than the supplied one.

    • Do not apply excessive force on the antenna. Doing so may damage it.

    • When packing the unit, remove the antenna to prevent damage.

    6 Connecting a network cable or the wireless antenna

    SPEAKERS

    NETWORK(NET)

    ZONE2/F.PRESENCE

    EXTRASP

    WIRELESS

    LAN

    WAN

    Network Attached Storage

    (NAS)

    Internet

    Modem

    Router

    Network cable

    PC

    The unit (rear)

    Mobile device(such as iPod touchand iPhone)

    a

    bWIRE

    LESS

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    31/146

    PREPARATIONS   ➤ Connecting other devices En 31

    Connecting an external power amplifier

    (RX-V777 only)

    When connecting an external power amplifier (pre-main amplifier) to enhance speaker

    output, connect the input jacks of the power amplifier to the PRE OUT jacks of the unit.

    The same channel signals are output from the PRE OUT jacks as from their

    corresponding SPEAKERS terminals.

    1 FRONT jacksOutput front channel sounds.

    2 SURROUND jacksOutput surround channel sounds.

    3 SUR. BACK jacksOutput surround back channel sounds. When using only one external amplifier for the surround

    back channel, connect it to the SINGLE jack (L side).

    4 SUBWOOFER1–2 jacksFor connecting a subwoofer with built-in amplifier. When 2 subwoofers are connected, the samesound is output from them.

    5 CENTER jack Outputs center channel sounds.

    Connecting recording devices

    You can connect video/audio recording devices to the AV OUT jacks. These jacks

    output analog video/audio signals selected as the input.

    • To copy video/audio from a video device, connect the video device to the AV 5–6 jacks of the unit.

    • To copy audio from an audio device, connect the audio device to the AV 5–6 jacks or AUDIO 1–2 jacks ofthe unit.

    • Be sure to use the AV OUT jacks only for connecting recording devices.

    7 Connecting other devices

    Caution

    • To prevent the generation of loud noises or abnormal sounds, make sure the followings before making

    connections.– Remove the power cable of the unit and turn off the external power amplifier before connecting them.

    – When using the PRE OUT jacks, do not connect speakers to the corresponding SPEAKERSterminals.

    – When using an external amplifier that does not have the volume control bypass, do not connect otherdevices (except the unit) to the amplifier.

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5(BD/DVD)

    ANTENNA

    FMAM

    FRONT CENTER   SURROUND

    SINGLE

    SURROUNDBACK/BI-AMP

    SPEAKERS

    AV6 AVOUT ZONE OUT   SUBWOOFERSUR.BACKSURROUNDFRONT

    PRE OUT

    CENTER

    SINGLE

    ZONE 2

    NETWORK(NET)

    ZONE2/F.PRESENCE

    EXTRA SP

    CENTER

    1

    2

    (RADIO)

    WIRELESS

    1 2 3 4 5

    The unit (rear)

    AUDIO1 AUDIO2

    AL

    AL

    IAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    COMPONENTVIDEO

    VIDEO

    MONITOR OUT

    PB

    Y

    PR

    HDMI 1 HDMI 2 HDMI 3 HDMI 4(BD/DVD)

    12

    ARC

    ANTENNA

    FMAM

    AV5

    VIDEO

    AV6 AVOUT ZONE OUT   SUBWOSUR.BACKSURROUNDFRONT

    PRE OUT

    CEN

    SINGLE

    ZONE 2

    DC OUT5V 0.5A

    COMPONENT VIDEO

    CENT

    1

    2

    HDMI OUT

    (RADIO)

    R

    L

    AUDIO

    R

    L

    AUDIOAV OUT

    VIDEO

    V V

    L

    R

    L

    R

    L

    R

    The unit (rear)AV OUT jacks

    Video/audio input

    Video recordingdevice

    Audio recordingdevice

    Audio input

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    32/146

    PREPARATIONS   ➤ Connecting the power cable En 32

    Connecting a device compatible with the trigger function

    The trigger function can control an external device in conjunction with operating the

    unit (such as powering on/off and input selection). If you have a Yamaha subwoofer that

    supports a system connection or a device with a trigger input jack, you can use the

    trigger function by connecting the external device to the TRIGGER OUT jack.

    • You can configure the trigger function settings in “Trigger Output” (p.111) in the “Setup” menu.

    After all the connections are complete, plug in the power cable.

    AUDIO1 AUDIO2

    OPTICAL

    OPTICAL

    COAXIAL

    VIDEO

    AV4

    AV3

    AV2

    AV1

    (TV)

    PBY PR

    HDMI 1 HD(BD/DVD)

    12

    ARC

    ANTENNA

    AM

    AV5

    VIDEO

    AV6 AVOUT

    DC OUT

    TRIGGER OUT

    REMOTE

    5V 0.5A

    12V

    IN

    OUT

    0.1A

    COMPONENT VIDEO

    HDMI OUT

    (RADIO)

    TRIGGER OUT

    12V   0.1A

    The unit (rear)

    TRIGGER OUT jack

    Systemconnection

    input

    Yamaha subwoofer thatsupports a system connection

    8 Connecting the power cable

    Before connecting the power cable (General model only)

    Set the switch position of VOLTAGE SELECTOR according to your local voltage.

    Voltages are AC 110–120/220–240 V, 50/60 Hz.

    • Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an ACwall outlet. Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create apotential fire hazard.

    UND

    SINGLE

    SURROUNDBACK/BI-AMP

    ZONE2/F.PRESENCE

    EXTRA SP

    WIRELESS

    220V-240V

    110V-120V

    VOLTAGE SELECTORThe unit (rear)

    VOLTAGE SELECTOR

    CENTER   SURROUND

    SINGLE

    SURROUNDBACK/BI-AMP

    SPEAKERS

    NETWORK(NET)

    ZONE2/F.PRESENCE

    EXTRASP

    WIRELESS

    To an AC wall outlet

    The unit (rear)

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    33/146

    PREPARATIONS   ➤ Selecting an on-screen menu language En 33

    Select the desired on-screen menu language from English

    (default), Japanese, French, German, Spanish, Russian, Italian and

    Chinese.

    1 Pressz (receiver power) to turn on the unit.

    2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).

    3 Press ON SCREEN.

    4 Use the cursor keys to select “Setup” and pressENTER.

    5 Use the cursor keys (e / r) to select “Language” andthe cursor keys (q / w) to select the desired

    language.

    6 To confirm the setting, press ENTER.

    7 To exit from the menu, press ON SCREEN.

    • The information on the front display is provided in English only.

    9 Selecting an on-screen menu language

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    ONE

    D

    CENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    Cursor keys

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    34/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 34

    The Yamaha Parametric room Acoustic Optimizer (YPAO) function

    detects speaker connections, measures the distances from them to

    your listening position(s), and then automatically optimizes the

    speaker settings, such as volume balance and acoustic

    parameters, to suit your room.

    • The YPAO function of the unit adopts the YPAO-R.S.C. (Reflected Sound Control)technology that enables to create natural sound fields like a room specificallydesigned for acoustic perfection.

    • Note the following regarding YPAO measurement.– Test tones are output at high volume and may surprise or frighten small children.

    – Test tone volume cannot be adjusted.

    – Keep the room as quiet as possible

    – Stay in a corner of the room behind the listening position so that you do notbecome an obstacle between speakers and the YPAO microphone.

    – Do not connect headphones.

    1 Pressz (receiver power) to turn on the unit.

    2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).

    3 Turn on the subwoofer and set the volume to half. Ifthe crossover frequency is adjustable, set it to

    maximum.

    • If you are using bi-amp connection or Zone2 speakers, set “Power AmpAssign” (p.100) in the “Setup” menu to the appropriate setting beforestarting YPAO.

    4 Place the YPAO microphone at your listeningposition and connect it to the YPAO MIC jack on thefront panel.

    • Place the YPAO microphone at your listening position (same height as yourears). We recommend the use of a tripod as a microphone stand. You canuse the tripod screws to stabilize the microphone.

    10 Optimizing the speaker settings automatically (YPAO)

    VOLUME HIGH CUT

    CROSSOVER/ 

    MIN MAXMIN MAX

    9

     YPAO MIC

    9

    1 2

    3

    4 5

    The unit (front)

    YPAOmicrophone

    Ear height

    YPAO MIC jack

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    N

    SCREEN   OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    P AR TY D MI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    (RX V677)

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    35/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 35

    (RX-V677)

    The following screen appears on the TV.

    This completes the preparations.

    See “Measuring at one listening position (single measure)”

    (p.36) to start the measurement.

    (RX-V777)

    The following screen appears on the TV.

    Proceed to Step 5.

    • To cancel the operation, disconnect the YPAO microphone before starting

    the measurement.

    • To configure the power amplifier assignment setting, press RETURN andselect “Manual Setup” (p.100).

    5 (RX-V777 only) If desired, change the measuringmethod (multi/single).

    a Use the cursor keys to select “Multi Position” and press ENTER.

    b Use the cursor keys to select a setting and then press ENTER.

    Settings

    • If you perform the multi measure, the speaker settings will be optimized for you toenjoy surround sound in a wider space.

    • If you perform the multi measure, first place the YPAO microphone at the listeningposition you will be seated most frequently.

    Yes

    Select this option if you will have several listeningpositions or if you want others to enjoy surround sound.You can take measurements at up to 8 differentpositions in the room. The speaker settings will beoptimized to suit the area defined by those positions(multi measure).

    No (default)

    Select this option if your listening position will always be

    fixed. Take the measurements at only one position. Thespeaker settings will be optimized to suit that position(single measure).

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    N

    SCREEN   OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    P AR TY D MI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ENTER

    RETURN

    Cursor keys

    M i t li t i iti

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    36/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 36

    This completes the preparations. See the following page to start the

    measurement.

    When “Multi Position” is set to “Yes”:

    “Measuring at multiple listening positions (multi measure) (RX-V777

    only)” (p.37)

    When “Multi Position” is set to “No”:

    “Measuring at one listening position (single measure)” (p.36)

    Measuring at one listening position(single measure)

    Follow the procedure below for measurement. It takes about

    3 minutes to perform the measurement.

    1 To start the measurement, use the cursor keys toselect “Measure” and press ENTER.

    The measurement will start in 10 seconds. Press ENTER

    again to start the measurement immediately.

    • To cancel the measurement temporarily, press RETURN.

    The following screen appears on the TV when themeasurement finishes.

    • If any error message (such as E-1) or warning message (such as W-1)appears, see “Error messages” (p.40) or “Warning messages” (p.41).

    • To check the measurement results, select “Result”. For details, see

    “Checking the measurement results” (p.39).

    2 Use the cursor keys to select “Save/Cancel” andpress ENTER.

    a b

    a

    a

    b

    c

    d

    e

    c

    d

    d e

    bac

    Multi measure(5 listening positions)

    Multi measure(2 listening positions + front/back)

    Multi measure(1 listening position + front/back/left/right)

    Single measure

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    N

    SCREEN   OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    ONE

    D

    CENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ENTER

    RETURN

    Cursor keys

    Measuring at multiple listening positions

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    37/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 37

    3 To save the measurement results, use the cursorkeys (e / r) to select “SAVE” and press ENTER.

    The adjusted speaker settings are applied.

    • To finish the measurement without saving the result, select “CANCEL”.

    4 Use the cursor keys (e / r) to select “YES” or “NO”to enable/disable YPAO Volume and press ENTER.

    • If YPAO Volume is enabled, the high- and low-frequency levels areautomatically adjusted according to the volume so that you can enjoynatural sounds even at low volume.

    • You can also enable/disable YPAO Volume in “YPAO Volume” (p.88) in the“Option” menu.

    5 Disconnect the YPAO microphone from the unit.This completes optimization of the speaker settings.

    Measuring at multiple listening positions(multi measure) (RX-V777 only)

    When “Multi Position” is set to “Yes”, follow the procedure below for

    measurement. It takes about 10 minutes to measure 8 listening

    positions.

    • If any error message (such as E-1) or warning message (such as W-1) appears,see “Error messages” (p.40) or “Warning messages” (p.41).

    1 To start the measurement, use the cursor keys toselect “Measure” and press ENTER.

    The measurement will start in 10 seconds. Press ENTERagain to start the measurement immediately.

    • To cancel the measurement temporarily, press RETURN.

    The following screen appears on the TV when the

    measurement at the first position finishes.

    2 Move the YPAO microphone to the next listeningposition and press ENTER.Repeat Step 2 until measurements at all listening positions

    (up to 8) have been taken.

    Caution

    • The YPAO microphone is sensitive to heat, so should not be placed anywherewhere it could be exposed to direct sunlight or high temperatures (such as on

    top of AV equipment).

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    N

    SCREEN   OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ENTER

    RETURN

    Cursor keys

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    38/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 38

    3 When the measurements at the positions you wantto measure are completed, use the cursor keys to

    select “CANCEL” and press ENTER.

    When you have taken measurements at 8 listening

    positions, the following screen appears automatically.

    • To check the measurement results, select “Result”. For details, see“Checking the measurement results” (p.39).

    4 Use the cursor keys to select “Save/Cancel” andpress ENTER.

    5 To save the measurement result, use the cursorkeys to select “SAVE” and press ENTER.

    The adjusted speaker settings are applied.

    • To finish the measurement without saving the result, select “CANCEL”.

    6 Use the cursor keys (e / r) to select “YES” or “NO”to enable/disable YPAO Volume and press ENTER.

    • If YPAO Volume is enabled, the high- and low-frequency levels areautomatically adjusted according to the volume so that you can enjoynatural sounds even at low volume.

    • You can also enable/disable YPAO Volume in “YPAO Volume” (p.88) in the“Option” menu.

    7 Disconnect the YPAO microphone from the unit.This completes optimization of the speaker settings.

    Caution

    • The YPAO microphone is sensitive to heat, so should not be placed anywherewhere it could be exposed to direct sunlight or high temperatures (such as ontop of AV equipment).9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    N

    SCREEN   OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    ONE

    D

    CENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ENTER

    Cursor keys

    Checking the measurement results 3

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    39/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 39

    Checking the measurement results

    You can check the YPAO measurement results.

    1 After the measurement, use the cursor keys toselect “Result” and press ENTER.

    • You can also select “Result” from “Auto Setup” (p.98) in the “Setup” menu,which displays the previous measurement results.

    The following screen appears.

    1Measurement result items

    2Measurement result details

    3 The number of measured positions (when multi

    measure is performed) * RX-V777 only

    2 Use the cursor keys to select an item.

    3 To finish checking the results and return to theprevious screen, press RETURN.

    Reloading the previous YPAO adjustmentsWhen the speaker settings you have configured manually are not

    suitable, follow the procedure below to discard the manual settings

    and reload the previous YPAO adjustments.

    1 In the “Setup” menu, select “Speaker”, “AutoSetup”, and then “Result” (p.97).

    2 Use the cursor keys to select “Setup Reload” andpress ENTER.

    3 To exit from the menu, press ON SCREEN.Wiring

    Polarity of each speaker

    Reverse: The speaker cable may be connected with thereverse polarity (+/-).

    Size

    Size of each speaker (cross-over frequency of the

    subwoofer)Large: The speaker can reproduce low-frequencysignals effectively.

    Small: The speaker cannot reproduce low-frequencysignals effectively.

    Distance Distance from the listening position to each speaker

    Level Output level adjustment for each speaker

    12

    3

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    RETURN

    Cursor keys

    Error messages

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    40/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 40

    Error messages

    If any error message is displayed during the measurement, resolve the problem and perform YPAO again.

    Error message Cause Remedy

    E-1: No Front SP Front speakers are not detected.

    Follow the on-screen instructions to exit YPAO, turn off the unit, and then check the speaker connections.E-2: No Sur. SP One of the surround speakers cannot be detected.

    E-3: No F.PRNS SP One of the presence speakers cannot be detected.

    E-4: SBR → SBL A surround back speaker is connected to the R side only.When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow theon-screen instructions to exit YPAO, turn off the unit, and then reconnect the speaker.

    E-5: Noisy The noise is too loud.Keep the room quiet and follow the on-screen instructions to start the measurement again. If you select“PROCEED”, YPAO takes the measurement again and ignores any noise detected.

    E-6: Check Sur. Surround back speakers are connected, but no surroundspeakers are connected.

    Surround speakers need to be connected in order to use surround back speakers. Follow the on-screeninstructions to exit YPAO, turn off the unit, and then reconnect the speakers.

    E-7: No MIC The YPAO microphone has been removed.Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start themeasurement again.

    E-8: No Signal The YPAO microphone cannot detect test tones.Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start themeasurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or servicecenter.

    E-9: User Cancel The measurement has been canceled. Fol low the on-screen instructions to start the measurement again. To cancel the measurement, select “EXIT”.

    E-10: Internal Error An internal error has occurred. Follow the on-screen instructions to exit YPAO, turn off and on the unit. If this error occurs repeatedly, contactthe nearest authorized Yamaha dealer or service center.

    Warning messages

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    41/146

    PREPARATIONS   ➤ Optimizing the speaker settings automatically (YPAO) En 41

    Warning messages

    If a warning message is displayed after the measurement, you can still save the measurement results by following on-screen instructions.

    However, we recommend you perform YPAO again in order to use the unit with the optimal speaker settings.

    Warning message Cause Remedy

    W-1: Out of PhaseA speaker cable may be connected with the reverse polarity(+/-).

    Select “Wiring” in “Result” (p.39) and check the cable connections (+/-) of the speaker identified by“Reverse”.

    If the speaker is connected incorrectly:

    Turn off the unit and then reconnect the speaker cable.

    If the speaker is connected correctly:

    Depending on the type of speakers or room environment, this message may appear even i f the speakers areconnected correctly. In this case, you can ignore the message.

    W-2: Over Distance

    A speaker is placed more than 24 m (80 ft) from the listening

    position.

    Select “Distance” in “Result” (p.39) and move the speaker identified by “>24.00m (>80.0ft)” within 24 m (80

    ft) of the listening position.

    W-3: Level ErrorThere are significant volume differences between thespeakers.

    Check the usage environment and cable connections (+/-) of each speaker, and the volume of thesubwoofer. We recommend using the same speakers or speakers with specifications that are as similar aspossible.

    11 Connecting to a network device wirelessly

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    42/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 42

    Connect the unit to a wireless router (access point) or a mobile device by establishing a

    wireless connection.

    Selecting the connection method

    Select a connection method according to your network environment.

    ■ Connecting with a wireless router (access point)Connect the unit to a wireless router (access point).

    You can enjoy Internet radio, AirPlay, or music files stored on media servers (PC/NAS)

    on the unit.

    For details on connection, see “Connecting the unit to a wireless network” (p.43).

    • You cannot use the wireless network connection simultaneously with the wired (network cable) connection(p.30) or Wireless Direct (p.48).

    • If the unit and the wireless router (access point) are too far apart, the unit may not connect to a wirelessrouter (access point). In such case, place them close to each other.

    ■ Connecting without a wireless router (access point)Connect a mobile device to the unit directly.

    You can use the application for smartphone / tablet “AV CONTROLLER” to control theunit from mobiles devices or enjoy music files stored on mobiles devices on the unit.

    For details on connection, see “Connecting a mobile device to the unit directly

    (Wireless Direct)” (p.48).

    • You cannot use Wireless Direct simultaneously with the wired (network cable) connection (p.30) or thewireless network connection (p.43).

    • When Wireless Direct is enabled, the following functions are not available.– Internet radio

    – Network services

    – Playback of music stored on media servers (PC/NAS)

    • For details on “AV CONTROLLER”, visit the Yamaha website.

    11 Connecting to a network device wirelessly

    The unit

    Wireless router

    Mobile device(such as iPhone)

    Internet

    Modem

    The unitMobile device(such as iPhone)

    Connecting the unit to a wireless network  4 Use the cursor keys to select “Setup” and press

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    43/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 43

    g

    There are several methods to connect the unit to a wireless

    network.

    Select a connection method according to your environment.

    ■ A: Sharing the iOS device settingYou can easily setup a wireless connection by applying the

    connection settings on iOS devices (iPhone/iPad/iPod touch).Before proceeding, confirm that your iOS device is connected to a

    wireless router.

    • You need iOS device with iOS 5.0 or later. For details on supported devices, see“Supported devices and file formats” (p.131).

    1 Pressz (receiver power) to turn on the unit.

    2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).

    • Operations with TV screen are available only when your TV is connected tothe unit via HDMI.

    3 Press ON SCREEN.

    4 Use the cursor keys to select Setup and pressENTER.

    5 Use the cursor keys (e / r) to select “Network”.

    6 Use the cursor keys (q / w) to select “NetworkConnection” and press ENTER.

    7 Use the cursor keys (q / w) and ENTER to check“Wireless (Wi-Fi)” and select “OK”.

    • The checkmark indicates the current setting.

    8 Use the cursor keys (q / w) and ENTER to check“Share Wi-Fi Settings (iOS)” and select “NEXT”.

    YesDo you own iOS devices

    (iPhone/iPad/iPod touch)?

    Yes

    A (p.43)

    B (p.44)Does your wireless router

    (access point) has a WPS

    button?

    C (p.45)

    No

    No

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    Cursor keys

    9 Connect the iOS device to the USB jack and disable ■B: Using the WPS push button

    f

    1 2 3 4 5 6 7 8 9 10 11

    z

  • 8/21/2019 Yamaha RX-V677 manual

    44/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 44

    9 Connect the iOS device to the USB jack, and disablethe screen lock on the iOS device.

    10Use the cursor keys (e / r) to select “NEXT” andpress ENTER.

    11Tap “Allow” in the message appeared on the iOSdevice.

    When the connection process finishes, “Completed”

    appears on the TV screen.

    12To exit from the menu, press ON SCREEN.

    configurationYou can easily set up a wireless connection with one push of the

    WPS button.

    • This configuration does not work if the security method of your wireless router(access point) is WEP. In this case, use other connection method.

    1 Pressz (receiver power) to turn on the unit.

    2 Hold down INFO (WPS) on the front panel for 3seconds.

    “Press WPS button on Access Point” appears on the frontdisplay.

    3 Push the WPS button on the wireless router (accesspoint).

    When the connection process finishes, “Completed”

    appears on the front display.

    If “Not connected” appears, repeat from Step 1 or try

    another connection method.

    VIDEOHDMI/  5 V 2 .1 A

    VIDEO AUX

    M HL 5V 1A2.1A

    The unit (front)

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    Cursor keys

    ■ C: Using other connection methods 8 Use the cursor keys ( / ) and ENTER to select the

    1 2 3 4 5 6 7 8 9 10 11

    z

  • 8/21/2019 Yamaha RX-V677 manual

    45/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 45

    If your wireless router (access point) does not support WPS push

    button configuration method, follow the procedure below to

    configure the wireless network settings.

    1 Pressz (receiver power) to turn on the unit.

    2 Turn on the TV and switch the TV input to displayvideo from the unit (HDMI OUT jack).

    • Operations with TV screen are available only when your TV is connected tothe unit via HDMI.

    3 Press ON SCREEN.

    4 Use the cursor keys to select “Setup” and pressENTER.

    5 Use the cursor keys (e / r) to select “Network”.

    6 Use the cursor keys (q / w) to select “NetworkConnection” and press ENTER.

    7 Use the cursor keys (q / w) and ENTER to check“Wireless (Wi-Fi)” and select “OK”.

    • The checkmark indicates the current setting.

    8 Use the cursor keys (q / w) and ENTER to select thedesired connection method and select “NEXT”.

    The following connection methods are available.

    WPS ButtonYou can set up a wireless connection with theWPS button while viewing the TV screen. Followthe instructions displayed on the TV screen.

    Share Wi-FiSettings (iOS)

    See “Sharing the iOS device setting” (p.43).

    Access PointScan

    You can set up a wireless connection bysearching for an access point. For details onsettings, see “Searching for an access point”(p.46).

    Manual Setting

    You can setup a wireless connection by enteringthe required information (such as SSID)

    manually. For details on settings, see “Setting upthe wireless connection manually” (p.46).

    PIN Code

    You can set up a wireless connection by enteringthe unit’s PIN code into the wireless router(access point). The method is available if thewireless router (access point) supports the WPSPIN code method. For details on settings, see“Using the PIN code” (p.47).

    About WPS

    WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance,which allows easy establishment of a wireless home network.

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    Cursor keys

    ❑ Searching for an access point

    If l “A P i S ” h i h d h

    ❑ Setting up the wireless connection manually

    If l “M l S i ” h i h d h

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    46/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 46

    If you select “Access Point Scan” as the connection method, the

    unit starts searching for access points. After a while, the list of

    available access points appears on the TV screen.

    1 Use the cursor keys and ENTER to check thedesired access point and select “NEXT”.The wireless connection setting screen appears on the TV.

    2 Use the cursor keys and ENTER to enter thesecurity key and select “NEXT”.

    3 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.When the connection process finishes, “Completed”

    appears on the TV screen.

    If “Not connected” appears, repeat from Step 1 or try

    another connection method.

    4 To exit from the menu, press ON SCREEN.

    If you select “Manual Setting” as the connection method, the

    wireless connection setting screen appears on the TV.

    You need to setup the SSID (network name), encryption method

    and security key for your network.

    1 Use the cursor keys and ENTER to enter the SSID ofthe access point and select “NEXT”.

    2 Use the cursor keys (q / w) and ENTER to check thesecurity method of the access point and select

    “NEXT”.

    Settings

    None, WEP, WPA-PSK (TKIP), WPA-PSK (AES), WPA2-PSK (AES),Mixed Mode

    9 0   ENTMEMORY

    5   6   87

    1 2 3 4

    MOVIE

    ENHANCER

    TUNING PRESET

    BAND

    DISPLAYRETURN

    ENTER

    ON

    SCREEN   OPTION

    TOPMENU

    MUTEP ROGR AM V OL UM E

    POP-UP/MENU

    PURE DIRECT

    STRAIGHT

    I NF O S LE EP

    MUSIC

    NET

    PARTY HDMI OUT

    TUNER

    MAIN ZONE 2

    USB

    MODE

    SCENE

    BDDVD

      TV NET   RADIO

    HDMI

    AV

    AUDIO

    5

    65

    V-AUX

    1 2 3 4

    1 2

    1 2

    3 4

    SUR. DECODE

    0   ENTMEMORY

    6

    1 2 3 4

    M VI

    ENHAN

    T NIN RE ET

    DI PLA

    OPTION

    TOPMENU

    P ROGR AM V OL UM E

    POP-UP/MENU

    P RE DIRE

    TRAI

    INF LEE

    M I

    NET

    PARTY HDMI OUT

    TUNER

    NE

    D

    SCENE

    DDVD

      O

    HDMI

    AV

    5

    65

    -AUX

    1 2 3 4

    1 2

    1 2

    3 4

    R . D E D

    ON SCREEN

    ENTER

    Cursor keys

    3 Use the cursor keys and ENTER to enter the❑ Using the PIN code

    If you select “PIN Code” as the connection method the list of

    1 2 3 4 5 6 7 8 9 10 11

  • 8/21/2019 Yamaha RX-V677 manual

    47/146

    PREPARATIONS   ➤ Connecting to a network device wirelessly En 47

    3 ysecurity key and select “NEXT”.

    If you select “None” in Step 2, this setting is not available.

    Proceed to Step 4.

    If you select “WEP”, enter either 5 or 13 character string, or10 or 26 hexadecimal digits.

    If you select other method, enter either 8 to 63 character

    string, or 64 hexadecimal digits.

    4 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.

    When the connection process finishes, “Completed”appears on the TV screen.

    If “Not connected” appears, check that all the information is

    entered correctly, and repeat from Step 1.

    5 To exit from the menu, press ON SCREEN.

    If you select “PIN Code” as the connection method, the list of

    available access points appears on the TV screen.

    1 Use the cursor keys and ENTER to check thedesired access point and select “NEXT”.

    The PIN code of the unit appears on the TV screen.

    2 Enter the unit’s PIN code into the wireless router(access point).

    For details on settings, refer to the instruction manual of the

    wireless router (access point).

    3 Use the cursor keys (e / r) to select “CONNECT”and press ENTER to start the connection process.When the connection process finishes, “Completed”

    appears on the TV screen.

    If “Not connected” appears, repeat from Step 1 or try

    another connection method.

    4 To exit from the menu, press ON SCREEN.

    9 0   ENTMEMORY

    5   6 �