Yamaha f350 Guage Round Catalague

COMMAND LINKMULTIFUNCTION METER

(ROUND)

OPERATION MANUAL

6Y8-2819V-00

To the ownerThank you for choosing the Yamaha Com-mand Link Multifunction Meter.This Operation Manual contains informationyou will need for proper operation.A thorough understanding of these simpleinstructions and of those in the Owner’sManual of the outboard motor will help youobtain maximum enjoyment of your newYamaha. This manual should be considereda permanent part of this meter and shouldremain with it even if the meter is subse-quently sold.In this Operation Manual particularly impor-tant information is distinguished in the fol-lowing ways.

The Safety Alert Symbol meansATTENTION! BECOME ALERT! YOURSAFETY IS INVOLVED!

WARNINGFailure to follow WARNING instructionscould result in severe injury or death tothe machine operator, a bystander, or aperson inspecting or repairing the out-board motor.

CAUTION:A CAUTION indicates special precau-tions that must be taken to avoid damageto the outboard motor.

NOTE:A NOTE provides key information to makeprocedures easier or clearer.

COMMAND LINK MULTIFUNCTION METER

(ROUND)OPERATION MANUAL

©2005 by Yamaha Motor Co., Ltd.1st Edition, March 2005

All rights reserved.Any reprinting or unauthorized usewithout the written permission of

Yamaha Motor Co., Ltd.is expressly prohibited.

Printed in Japan

The Command Link Multifunction Meterenables the display of information throughdigital communication with the engine.

Optional parts such as the speed sensor,cooling water pressure sensor, Triducer-Multi sensor, and GPS are described in thismanual by assuming that the parts areinstalled and set up on the outboard motor.

The Command Link Multifunction Meterdescribed in this manual consists of the fol-lowing.

• Tachometer unit(Part No.: 6Y8-8350T-1*)

• Speed & Fuel meter unit(Part No.: 6Y8-83500-1*)

The Command Link Multifunction Meter iscompatible with the following outboardmotors.

4-stroke models:Fuel injection models only2-stroke models:HPDI models only

The operations of the set button and themode button are described in this manual asfollows.

Button operations:

•Press the set button one time.

•Press the mode button one time.

• orPress the set button or the mode buttonone time.

• (1 second)Press the set button for 1 second.

• (4 seconds)Press the mode button for 4 seconds.

• (10 seconds)Press the set button for 10 seconds.

• (1 second) (2 times)Press the mode button two times, 1 sec-ond each time.

• +Press the set button and the mode buttonsimultaneously.

• + (1 second)Press the set button and the mode buttonsimultaneously for 1 second.

Table of contents

Tac

hom

eter

uni

tS

peed

& F

uel m

eter

un

itS

ettin

g up

the

met

ers

1. Tachometer unit ....................... 1Description .................................. 2Activating the meter .................... 2

Periodic maintenance notification ............................. 3

Tachometer ................................. 3Trim meter................................... 3Multifunction display.................... 4

Cooling water/engine temperature display............... 5

Battery voltage display ............. 6Total hour/Trip hour display ..... 7Cooling water pressure display

(optional: cooling water pressure sensor has been installed)................................ 7

Oil pressure display (4-stroke models) .................. 8

Oil level display (2-stroke models) .................. 9

Water detection warning .......... 9Changing backlight settings ...... 10Adjusting trolling speed ............. 10Changing settings

(custom mode) ....................... 11Switching to custom mode ..... 1101 (resetting maintenance

intervals).............................. 1202 (setting trim angle) ............ 1203 (setting corresponding

engine) ................................ 13Service functions....................... 14

Diagnosis ............................... 14Resetting engine number ....... 15

2. Speed & Fuel meter unit ........ 16Description ................................ 17Activating the meter .................. 17Speedometer............................. 18Fuel meter ................................. 19Multifunction display.................. 19

Fuel flow display .................... 20Fuel economy display ............ 21Total fuel consumption

display................................. 21Ambient water temperature

display (optional: Triducer-multi sensor has been installed) .................... 22

Depth display (optional: Triducer-multi sensor has been installed) .................... 22

Clock (optional: GPS has been installed) .................... 23

Trip display (optional: speed sensor has been installed) ............................. 23

Changing backlight settings ...... 23Changing settings

(custom mode)....................... 24Switching to custom mode..... 2401 (setting displayed units) .... 2402 (setting fuel sensor) .......... 2603 (setting correction value) .. 26

3. Setting up the meters ............ 28Activating for the first time......... 28Setting the initial settings .......... 28

Tachometer unit ..................... 28Speed & Fuel meter unit: ....... 28

1

1. Tachometer unit

NOTE:Depending on the model of the outboard motor, some functions may not be compatible. Forinformation on models which contain the compatible functions, consult a Yamaha dealer.

Tachometer The tachometershows the enginerevolutions perminute. (Page 3)

Trim meterThe trim meter showsthe trim angle of theoutboard motor in 13levels. (Page 3)

Multifunction display (Page 4)· You can switch each engine information and show it using numeric valuesor graphics. In addition, when an engine malfunction occurs, each indicatorblinks to warn of the malfunction.Cooling water/engine temperature display (Page 5)Battery voltage display (Page 6)Total hour/Trip hour display (Page 7)Cooling water pressure display (optional) (Page 7)Oil pressure display (4-stroke models) (Page 8)Oil level display (2-stroke models) (Page 9)Water detection warning (Page 9)

· Periodic maintenance intervals are notified.Periodic maintenance notification (Page 3)

Adjusting trolling speed

or : To adjust the trolling speedrandomly. (Page 10)

2

Tac

hom

eter

uni

t

Description

1 set button2 mode button

1 Tachometer2 Trim meter3 Multifunction display4 Water detection warning indicator5 Maintenance indicator6 Cooling water pressure7 Oil pressure (4-stroke models)8 Oil level (2-stroke models)9 Cooling water/engine temperature0 Battery voltage

Activating the meterWhen the engine start switch is turned toON, the meter is activated and“ ” appears on the multifunctionmeter. Then, all the displays come on andthe display switches to the normal displayafter the total hour display comes on.

21

1 2

3

45

6 7 8 9 0

Description/Activating the meter

3

Periodic maintenance notificationWhen the hours of engine operation exceed100 hours, the elapsed time from the previ-ous maintenance period (when the meterwas reset) blinks.

or : To return to the normal dis-play.

NOTE:• The elapsed time blinks every time the

engine is started until it is reset. In addi-

tion, the maintenance indicator ( )remains on until it is reset.

• When the hours of engine operationexceed 100 hours and the periodic main-tenance notification is activated, consultan authorized Yamaha dealer for periodi-cal maintenance.

• To reset the maintenance period, see “01(resetting maintenance intervals)” in“Changing settings (custom mode).”

TachometerThe tachometer shows the engine revolu-tions per minute.

Trim meterThe trim meter shows the trim angle of theoutboard motor in 13 levels.

When the angle of the outboard motorexceeds the trim range, the top segmentblinks.

Blinks

Blinks

Tachometer/Trim meter

4

Tac

hom

eter

uni

t

Multifunction displayThe multifunction display shows variousinformation using numeric values or graph-ics.

: Press to switch between the displays.

When the engine start switch is turned toOFF, the last display shown is shown firstwhen the engine start switch is turned to ONagain.

NOTE:If an optional sensor is not connected to themeter, the corresponding display will not bedisplayed.

Cooling water pressure

Oil pressure (4-stroke) Oil level (2-stroke)

Battery voltage level/Battery voltage value

Cooling water/engine temperature

Total hour/Trip hour

Multifunction display

5

Cooling water/engine temperature displayThe cooling water/engine temperature indi-

cator ( ) comes on and the coolingwater temperature or the engine tempera-ture is shown in 6 levels.

When the engine overheats, the cooling

water/engine temperature indicator ( )blinks to warn of the malfunction.

CAUTION:• When the overheat warning comes on,

turn the engine off and check the cool-ing water inlet for clogs.

• If you cannot locate and correct thecause, consult a Yamaha dealer.

NOTE:The cooling water/engine temperature dis-play shows “L” for low and “H” for high.

Blinks

Cooling water/engine temperature display

6

Tac

hom

eter

uni

t

Battery voltage display

The battery voltage indicator ( ) comeson and the battery voltage of the engine isshown in 6 levels or the voltage value isshown.

: Press to switch between the displayformats.

When the battery voltage decreases to 12volts or less or increases to 16 volts or morethe voltage value blinks.

When the battery voltage decreases belowthe voltage that is required by the engine,

the battery voltage indicator ( ) blinksto warn of the malfunction.

CAUTION:• When the low battery voltage warning

comes on, check the battery and thewiring.


NOTE:The battery voltage level display shows “L”for low and “H” for high.

Battery voltage level

Battery voltage value

Blinks

Blink

Battery voltage display

7

Total hour/Trip hour displayThe total hour display shows the total hoursof engine operation and the trip hour displayshows the trip hours (T).

: Press to switch between the displayformats.

+ (1 second): To reset the triphours (T).

NOTE:The total hours of engine operation cannotbe reset.

Cooling water pressure display (optional: cooling water pressure sensor has been installed)

The cooling water pressure indicator ( )comes on and the cooling water pressure isshown in 6 levels.

CAUTION:• When the cooling water pressure

decreases to 10 psi or less, turn theengine off and check the cooling waterinlet for clogs.


NOTE:The cooling water pressure level displayshows “L” for low and “H” for high.

Total hour

Trip hour (T)

Blinks

Blinks

Blinks 10 psi

Total hour/Trip hour display/Cooling water pressure display

8

Tac

hom

eter

uni

t

Oil pressure display (4-stroke models)

The oil pressure indicator ( ) comes onand the engine oil pressure is shown in 6levels.

When the engine oil pressure drops too low,

the oil pressure indicator ( ) blinks towarn of the malfunction.

CAUTION:• Do not operate the engine without

engine oil. Severe engine damage canresult.

• Check the oil level by following theprocedure described in the engineOwner’s Manual.


NOTE:• The oil pressure display shows “L” for low

and “H” for high.• The low oil pressure warning does not dis-

play the engine oil level.• Depending on the model of the outboard

motor, the oil pressure display may not beavailable.

• Depending on the operating conditionssuch as when the engine is operated atextremely low speeds, the oil pressuremay be shown as low even when theengine is operating properly.

Blinks

Oil pressure display (4-stroke models)

9

Oil level display (2-stroke models)The oil level indicator ( ) comes on andthe engine oil level is shown in 3 levels.

When the engine oil level is low, the oil level

indicator ( ) blink to warn of the mal-function.

CAUTION:Do not operate the engine without engineoil. Severe engine damage can result.

Water detection warningWhen water has accumulated in the waterseparator (fuel filter), the water detection

warning indicator ( ) blinks to warn ofthe malfunction. This function is not avail-able for outboard motors that are notequipped with the water detection warningfunction.

CAUTION:When the water detection warning comeson, turn the engine off and remove thewater from the water separator (fuel fil-ter) by following the procedure describedin the Owner’s Manual of the outboardmotor. A malfunction can result if fuelmixed with water is sent to the engine.

NOTE:

or : To deactivate the buzzer.

Blink

Blinks

Oil level display (2-stroke models)/Water detection warning

10

Tac

hom

eter

uni

t

Changing backlight settingsYou can turn the backlight on or off, orchange the brightness level of the backlightfor all meters synchronized.

1. + : To activate the backlightmode.

2. : Press to switch between the fivebrightness levels (1–5).

: To switch between the backlighton and “OFF.”

3. + : To return to the normaldisplay.

NOTE:• The backlight default settings are “OFF”

and brightness level 1.• If no operations are carried out for 5 sec-

onds or more, the display returns to thenormal display.

• The backlight settings can be changedfrom all meters and all displays.

Adjusting trolling speedYou can adjust the trolling speed randomlyby increasing or decreasing it approximately50 r/min.When in the trolling speed setting mode, thedisplay switches to the normal display whenthe engine speed is increased (within 3,000r/min) using the throttle. When the throttle isclosed, the display returns to the trollingspeed setting mode.This function is not available for outboardmotors that are not equipped with the trollingspeed adjustment function.

1. (1 second): To activate the trollingspeed setting mode.

2. : To decrease the engine speed.

3. : To increase the engine speed.

4. : To return to the normal displayand to the default engine idle speed.

Changing backlight settings/Adjusting trolling speed

11

NOTE:• Trolling is affected by currents and other

operating conditions and may differ fromthe actual engine speed.

• The default engine idle speed is resetautomatically when the display is switchedto the normal display. The default engineidle speed is also reset automaticallywhen the engine is turned off or when theengine speed exceeds 3,000 r/min.

• When warming up a cold engine, the troll-ing speed cannot be decreased below thespecified engine idle speed.

• Depending on the model of the outboardmotor, some functions may not be com-patible. For information on models whichcontain the compatible functions, consulta Yamaha dealer.

Changing settings (custom mode)Switching to custom modeIn the custom mode, you can change themeter function settings. Each setting func-tion number is shown in the tachometer dis-play.1. Turn the engine off and the engine start

switch to ON.

2. (4 seconds): To activate the cus-tom mode.

3. (1 second): Press to switchbetween the setting function numbersand to switch to the change settings dis-play.

4. Change each setting and return to thenormal display. To change the settings,see the corresponding sections for eachsetting function.

NOTE:If no operations are carried out for 30 sec-onds or more or if the engine is started, thesettings will not be applied and the displayreturns to the normal display.

01 (resetting maintenance intervals)

03 (setting corresponding engine)

02 (setting trim angle)

(1sec.)

(1sec.)

(1sec.)

Changing settings (custom mode)

12

Tac

hom

eter

uni

t

01 (resetting maintenance intervals)You can reset the elapsed time from theprevious maintenance interval (when themeter was reset).1. Turn the engine off and the engine start

switch to ON.

2. (4 seconds): To activate the cus-tom mode and to switch to the resettingdisplay.

3. + (1 second): To reset theelapsed time to “0h” and return to thenormal display.

NOTE:

Press the button for 1 second fromstep 2 to cancel the resetting of the elapsedtime and return to the normal display.

02 (setting trim angle)You can set the trim angle to zero.Fully trim the outboard motor down.1. Turn the engine off and the engine start

switch to ON.


3. (1 second): To switch betweenthe setting function numbers and toswitch to the zero adjustment display.

4. + (1 second): To adjust thetrim angle to zero using the current trimposition as the standard value andreturn to the normal display.

NOTE:• When one segment is displayed, the trim

angle of the outboard motor is adjusted tozero (full trim in).

• Press the button for 1 second fromstep 3 to cancel the adjustment of the trimangle to zero and return to the normal dis-play.

Blinks

01 (resetting maintenance intervals)/02 (setting trim angle)

13

03 (setting corresponding engine)You can select the engines that are compat-ible to this meter. The port outboard motor isset to “-1- (engine number 1)” and the star-board outboard motor is set to “-2- (enginenumber 2).”1. Turn the engine off and the engine start

switch to ON.


3. (1 second) (2 times): Press toswitch between the setting functionnumbers and to switch to the changesettings display.

4. : To switch between the displayedengine numbers.

5. (1 second): To change the corre-sponding engine and return to the nor-mal display.

NOTE:• The meters are set at the factory to

“-1- (engine number 1).”• To reset an engine number, see “Reset-

ting engine number” in “Service func-tions.”

-1- (engine number 1)




03 (setting corresponding engine)

14

Tac

hom

eter

uni

t

Service functionsDiagnosisYou can display the self-diagnosis results ofthe engine.

(10 seconds): To display the diagno-sis codes.

When there are no malfunctions, the “-01-”diagnosis code is displayed.

When a malfunction occurs, the correspond-ing diagnosis codes, except “-01-,” are dis-played.When there are multiple diagnosis codes,

press the button to display the nextcode number.

(1 second): To return to the normaldisplay.

CAUTION:When a diagnosis code other than “-01-”is displayed, the engine cannot be oper-ated normally. Consult a Yamaha dealer.

NOTE:Although the custom mode is activated after

a few seconds while the button isbeing pressed, continue to press the buttonfor 10 consecutive seconds to activate thediagnosis mode.

Service functions

15

Resetting engine numberWhen replacing the engines of multiple out-board motors or resetting the setting order,reset all engine numbers to “-1- (enginenumber 1).”1. Turn the engine off and the engine start

switch to ON.

2. (10 seconds): “-00-” will be dis-played for 1 second.

3. Turn the engine start switch to OFF.The engine number is reset afterapproximately 10 seconds.

4. Turn the engine start switches to ON inorder from port to starboard.

NOTE:• The engine numbers are stored in the

ECM (Engine Control Module) of eachengine for engine identification.

• The engine numbers are stored in theECM (Engine Control Module) when theengine start switch is first turned to ONafter being connected. The numbers arestored in order from number one to num-ber four starting from the port outboardmotor. When multiple outboard motors areinstalled, be sure to wait at least 2 sec-onds before turning each engine startswitch to ON.

Service functions

16

Spe

ed &

Fue

l met

er

unit

2. Speed & Fuel meter unit

NOTE:Depending on the model of the outboard motor, some functions may not be compatible. Forinformation on models which contain the compatible functions, consult a Yamaha dealer.

Speedometer Shows the speed ofthe boat. You canswitch the displayedunit to miles per hour(mph), knots, or kilometers per hour(km/h). (Page 18)

Fuel meterThe fuel meter showsthe remaining fuellevel in 8 levels.(Page 19)

Multifunction display (Page 19)· You can switch each engine information and show it using numeric values.

Fuel flow display (Page 20)Fuel economy display (Page 21)Total fuel consumption display (Page 21)Ambient water temperature display (optional) (Page 22)Depth display (optional) (Page 22)Clock (optional) (Page 23)Trip display (optional) (Page 23)

17

Description

1 set button2 mode button

1 Speedometer2 Fuel meter3 Multifunction display

Activating the meterWhen the engine start switch is turned toON, the meter is activated and

“ ” appears on the multifunctionmeter. Then, all the displays come on andthe display switches to the normal displayafter a few seconds.

21

1 2

3

Description/Activating the meter

18

Spe

ed &

Fue

l met

er

unit

SpeedometerThe speedometer shows the ground speedor the water speed of the boat.To display the ground speed, the GPS mustbe connected to the meter. To display thewater speed, an optional sensor (speedsensor or Triducer-Multi sensor) must beconnected to the meter.

Switching the speed sensors:

1. (4 seconds): To activate thespeed sensor setting mode.

2. : Press to switch between thespeed sensor types.

3. (1 second): To set the speed sen-sor and return to the normal display.

NOTE:• If no operations are carried out for 30 sec-

onds or more, the display returns to thenormal display.

• When signals from the GPS cannot bereceived even when the GPS function ison, the GPS display goes off and thewater speed is displayed.

• You can select to show miles per hour(mph), kilometers per hour (km/h), orknots on the speedometer display. Tochange the displayed unit, see “01 (set-ting displayed units)” in “Changing set-tings (custom mode).”

“On” (ground speed)

“OFF” (water speed)

Speedometer

19

Fuel meterThe fuel meter shows the remaining fuellevel in 8 levels and all the segments aredisplayed when the fuel tank is full. Whenthe fuel level is low, the last segment blinks.

NOTE:The fuel sensor setting can be changedaccording to the fuel sensor type. To changethe fuel sensor setting, see “02 (setting fuelsensor)” in “Changing settings (custommode).”

Multifunction displayThe multifunction display shows variousinformation using numeric values.

: Press to switch between the displays.

FLOW

ECON

TRIP

DPTH

TTL

Clock

TEMP

Fuel meter/Multifunction display

20

Spe

ed &

Fue

l met

er

unit

When the engine start switch is turned toOFF, the last display shown is shown firstwhen the engine start switch is turned to ONagain.

NOTE:• To change the various settings, see

“Changing settings (custom mode).”• If an optional sensor is not connected to

the meter, the corresponding display willnot be displayed.

Fuel flow displayFLOW shows the total fuel consumption perhour of all engines.

NOTE:You can select to show gallons per hour(gph) or liters per hour (l/h) on the FLOWdisplay. To change the displayed unit, see“01 (setting displayed units)” in “Changingsettings (custom mode).”

Fuel flow display

21

Fuel economy displayECON shows the distance traveled per unitof fuel.

NOTE:• Fuel economy is affected by the type of

boat being operated and the operatingconditions, and it is constantly changing.

• You can select to show miles per gallon(mpg), nautical miles per liter (nm/l), orkilometers per liter (km/l) on the ECONdisplay. To change the displayed unit, see“01 (setting displayed units)” in “Changingsettings (custom mode).”

Total fuel consumption displayTTL shows the total fuel consumption of allengines.

The TTL display cannot measure over 1,999gallons or 1,999 liters. When there are morethan 1,999 gallons or 1,999 liters of fuel, thenumeric value blinks to indicate an overflow.

+ (1 second): To reset the TTLdisplay.

NOTE:You can select to show gallons (g) or liters(l) on the TTL display. To change the dis-played unit, see “01 (setting displayedunits)” in “Changing settings (custommode).”

Blinks

Fuel economy display/Total fuel consumption display

22

Spe

ed &

Fue

l met

er

unit

Ambient water temperature display (optional: Triducer-multi sensor has been installed)TEMP shows the ambient water tempera-ture.

NOTE:You can select to show Fahrenheit (°F) orCelsius (°C) on the TEMP display. Tochange the displayed unit, see “01 (settingdisplayed units)” in “Changing settings (cus-tom mode).”

Depth display (optional: Triducer-multi sensor has been installed)DPTH shows the water depth.

NOTE:You can select to show feet (F) or meters(m) on the DPTH display. To change thedisplayed unit, see “01 (setting displayedunits)” in “Changing settings (custommode).”

Ambient water temperature display/Depth display

23

Clock (optional: GPS has been installed)The clock shows the time in 12 hours. Thelocal time is easily displayed by calculatingthe longitude information received from theGPS communication data. Set the time asnecessary.

Setting the time:

1. : To activate the time settingmode and switch to the time setting dis-play.

2. : To change the minutes. Pressand hold to advance quickly.

3. : To set the hours.

4. : To change the hours. Press andhold to advance quickly.

5. : To set the time and return to thenormal display.

Resetting the time:

1. : To activate the time setting modeand to switch to the time setting display.

2. + (1 second): To reset thetime to “0:00” and return to the normaldisplay.

Trip display (optional: speed sensor has been installed)TRIP shows the information from the speedsensor converted to the distance traveled.

+ (1 second): To reset the dis-tance traveled.

NOTE:• The distance traveled is affected by cur-

rents and other operating conditions andmay differ from the actual distance trav-eled.

• You can select to show miles (mile), nauti-cal miles (nm), or kilometers (km) on theTRIP display. To change the displayedunit, see “01 (setting displayed units)” in“Changing settings (custom mode).”

Changing backlight settingsYou can turn the backlight on or off, orchange the brightness level of the backlightfor all meters collectively.

NOTE:The backlight setting procedure is the sameas that of the tachometer unit.To change the backlight settings, see“Changing backlight settings” in “1. Tachom-eter unit.”

Blinks

Clock/Trip display/Changing backlight settings

24

Spe

ed &

Fue

l met

er

unit

Changing settings (custom mode)Switching to custom modeIn the custom mode, you can change themeter function settings. Each setting func-tion number is displayed in the speedometerdisplay.1. Turn the engine off and the engine start

switch to ON.


3. (1 second): Press to switchbetween the setting function numbersand to switch to the change settings dis-play.

4. Change each setting and return to thenormal display. To change the settings,see the corresponding sections for eachsetting function.

NOTE:If no operations are carried out for 30 sec-onds or more or if the engine is started, thesettings will not be applied and the displayreturns to the normal display.

01 (setting displayed units)You can change the units that are shown ineach display. The indicator of the selecteddisplay blinks.1. Turn the engine off and the engine start

switch to ON.

2. (4 seconds): To activate the cus-tom mode and to switch to the changesettings display.

3. : Press to switch between the dis-plays.

* In the display example, the speedometeris shown.

01 (setting displayed units)

03 (setting correction value)

02 (setting fuel sensor)

(1sec.)

(1sec.)

(1sec.)

FLOW (fuel flow)

TRIP (trip)

Speedometer

DPTH (depth)

TEMP(ambient water temperature)

TTL (total fuel consumption)

ECON (fuel economy)

Blinks

Changing settings (custom mode)/01 (setting displayed units)

25

4. : Press to switch between the dis-plays. In addition, you can select to notshow the display.

SpeedometerYou can select to show miles per hour(mph), kilometers per hour (km/h), or knots.The default setting is miles per hour (mph).TRIPYou can select to show miles (mile), nauticalmiles (nm), kilometers (km), or not to showthe display. The default setting is miles(mile).FLOWYou can select to show gallons per hour(gph), liters per hour (l/h), or not to show thedisplay. The default setting is gallons perhour (gph).ECONYou can select to show miles per gallon(mpg), nautical miles per liter (nm/l), kilome-ters per liter (km/l) or not to show the dis-play. The default setting is miles per gallon(mpg).TTLYou can select to show gallons (g), liters (l),or not to show the display. The default set-ting is gallons (g).TEMPYou can select to show Fahrenheit (°F), Cel-sius (°C), or not to show the display. Thedefault setting is Fahrenheit (°F).DPTHYou can select to show feet (F), meters (m),or not to show the display. The default set-ting is feet (F).

5. (1 second): To change the dis-played unit and return to the normal dis-play.

NOTE:• When the speedometer unit settings are

changed, the TRIP, FLOW, ECON, TTL,TEMP, and DPTH unit settings are collec-tively changed automatically. To changethe settings for each displayed unit indi-vidually, repeat steps 3 and 4.

• Press the and buttons simul-taneously for 1 second from step 2 toreset all displayed units to the default set-tings.

01 (setting displayed units)

26

Spe

ed &

Fue

l met

er

unit

02 (setting fuel sensor)You can set the fuel sensor type that is con-nected to this meter.1. Turn the engine off and the engine start

switch to ON.


3. (1 second): To switch betweenthe setting function numbers and toswitch to the change settings display.

4. : Press to switch between the fuelsensor types.

5. (1 second): To change the fuelsensor type and return to the normaldisplay.

03 (setting correction value)You can calibrate the displayed fuel flowvalue within –7 to +7 percent. The differencein the fuel consumption display and theactual fuel consumption is calibrated.

Checking the calibration value:1. Operate the outboard motor on a full

tank of fuel.2. After operating the outboard motor, fill

the fuel tank. Compare the amount offuel filled into the fuel tank with the fuelconsumed shown on the fuel consump-tion display and set the calibration valueto the difference if necessary.

Changing the calibration value:1. Turn the engine off and the engine start

switch to ON.


3. (1 second) (2 times): Press toswitch between the setting functionnumbers and to switch to the changesettings display.

4. : Press to switch between the cali-bration values.

5. (1 second): To change the cali-bration value and return to the normaldisplay.

-1- (ABYC-US)

-3- (YAMAHA)

-2- (EUROPE)

Blinks

02 (setting fuel sensor)/03 (setting correction value)

27

NOTE:• The fuel flow display may differ depending

on the operating conditions.• When the fuel flow calibration value is

changed, the FLOW, TTL, and ECON dis-plays are shown calibrated.

03 (setting correction value)

28

Set

ting

up th

e m

eter

s

3. Setting up the metersTo install the meters and the optional sen-sors and to connect the meters to theengine, see the “Command Link Multifunc-tion Meter Installation Manual.”Be sure to follow the procedures in “Activat-ing for the first time” and “Setting the initialsettings.” If the procedures are performedincorrectly, the engine number will change,resulting in improper operation.1. Installing the meters2. Connecting the meters to the engine3. Installing an optional sensor4. Activating for the first time5. Setting the initial settings

If the procedures are performed incorrectly,see “Service functions” in “1. Tachometerunit” to reset all of the engine numbers.Check the connections, and follow the setupprocedures again to set up the meters.

Activating for the first timeAfter installing the meters, be sure to turnthe engine start switch to ON when thepower is supplied for the first time. Whenmultiple outboard motors are installed, besure to turn the engine start switch to ONfrom the port outboard motor and to wait atleast 2 seconds before turning each enginestart switch to ON.

NOTE:• The engine number of the engine whose

engine start switch was first turned to ONis stored in the ECM (Engine Control Mod-ule) of the engine as the port engine(engine number 1).

• To reset an engine number, see “Reset-ting engine number” under “Service func-tions” in “1. Tachometer unit.”

Setting the initial settingsBefore operating the meter, be sure tochange the default settings as describedbelow. For the setting procedures, see thecorresponding setting procedure for eachmeter.

Tachometer unit03 (setting corresponding engine)Select the engines compatible to this meter.(See page 13.)

02 (setting trim angle)Adjust the trim angle to zero. (See page 12.)

Speed & Fuel meter unit02 (setting fuel sensor)Set the fuel sensor according to the fueltank type. (See page 26.)

Activating for the first time/Setting the initial settings

YAMAHA MOTOR CO., LTD.

Printed in JapanMarch 2005 – 1.0 × 1 CR Printed on recycled paper(E)

Documents

Yamaha f350 Guage Round Catalague