Upload
donhi
View
226
Download
0
Embed Size (px)
Citation preview
Whenever your system needs to communicate
COMMUNICATE WITH N.A.T.
The expert of high performance connectivity products for data and telecommunication solutions.
The MicroTCA Concept VI by N.A.T.
www.nateurope.com - innovation in communication
NATIVE-C1size· 1U 19” rack-mounted, depth: 206.0 mm
slots· 6 mid-size AMCs · 1 full-size MCH for fat pipe support
power supply· 110-265VAC, 600W output, front pluggable· -48VDC, 420W or 840W output, front pluggable· +24VDC, 300W or 600W output, front pluggable
cooling units· 2 redundant hot-swap fan trays
backplane configuration · direct SATA / SAS connections· single star base fabric and fat pipe,
PICMG compliant
NAMC-8569-xE1/T1Signalling processing engine providing 8 or 16 E1/T1 line interfaces including TDM cross connect and I-TDM interworking in mid-size or full-size form factor.
front panel interfaces· 8 E1/T1 (mid-size) or 16 E1/T1 (full-size)
backplane interfaces· 2x GbE and either of the following combinations:
SRIO x4, PCIe x4, 2x SRIO x1, PCIe x1 and SRIO x1, IPMI
on-board· TDM cross connection, TDM to I-TDM
interworking· PowerQUICC III MPC8569· Firmware: ISDN, SS7
NAMC-8569-ATMMulti-service ATM board featuring conversion between optical OC-3/STM1 ATM traffic, Ethernet and TDM data designated to connect systems to ATM legacy data, designated networks.
front panel interfaces· OC-3, OC-12, DS3 or Ethernet
backplane interfaces· 2x GbE and either of the following combinations:
SRIO x4, PCIe x4, 2x SRIO x1, PCIe x1 and SRIO x1, IPMI
on-board· PowerQUICC III MPC8569 · AAL1, AAL2 and AAL5 processing engine
NATIVE-C2size· 2U 19” rack-mounted, depth: 206.0 mm
slots· 12 mid-size AMCs, horizontally-mounted · 2 full-size MCHs for fat pipe support
power supply· 2 power modules· 110-265VAC, 600W output, front pluggable· - 48VDC, 420W or 840W output, front pluggable· +24VDC, 300W or 600W output, front pluggable
cooling units · 2 redundant hot-swap fan trays
backplane configuration · direct SATA / SAS connections· dual star base fabric and fat pipe,
PICMG compliant
Also available as Starter Kit
Pro
cess
orA
MC
s
NAMC-QorIQ-P3041Powerful packet processing engine with four cores, built on Power Architecture techno- logy, operating at up to 1.5GHz in mid-size form factor, designated for today‘s packet oriented network applications.
front panel interfaces· 1x GbE, 1x USB, 1x RS232
backplane interfaces· fat pipe: PCIe, SRIO or XAUI· base fabric: 2x GbE, 2x SATA
on-board· QorIQ P3041· Lattice ECP3
NAMC-QorIQ-P204xPowerful packet processing engine with four cores, built on Power Architecture techno- logy. The NAMC-QorIQ-P2040 operating at up to 1.2 GHz and the NAMC-QorIQ-P2041 at up to 1.5 GHz in mid-size form factor designated for today’s packet oriented network applications.
front panel interfaces· 1x GbE, 1x USB, 1x RS232
backplane interfaces· fat pipe: PCIe, SRIO or XAUI (P2041 only)· base fabric: 2x GbE, 2x SATA
on-board· QorIQ P2040· QorIQ P2041· Lattice ECP3
NAMC-8569-CPUMulti-service, low cost, low power, ge-neral purpose PrAMC, addressing high-performance broadband access equipment including 3G/WiMAX/LTE base stations, radio network controllers and gateways in mid-size form factor.
front panel interfaces· GbE, RS232, USB
backplane interfaces· 2x GbE and either of the following
combinations: SRIO x4, PCIe x4, 2x SRIO x1, PCIe x1 and SRIO x1
on-board· PowerQUICC III MPC8569 (1,3 GHz)· Lattice FPGA
Ch
assi
s an
d P
ow
er M
od
ule
s
NATIVE-minisize· 260.0 x 43.0 mm set-top, stackable· depth: 302.0 mm
slots· 2 single full-size· eMCH integrated
power supply· 90-264VAC, 150W output with on-off-switch
cooling unit· 5 integrated fans
backplane configuration· direct fabric connections except for 1GbE· 1GbE to eMCH (provides uplink at front-panel)
Lin
e In
terf
ace
Car
ds
NAMC-SDHSDH line interface for STM-1 or STM-4 SDH/SONET providing add/drop functionality at DS0 and subrate level including TDM cross-bar and I-TDM interworking and optional data handling by onboard Kintex-7 FPGA.
front panel interfaces· 4x OC-3 or 2x OC12 (2nd OC12 for backup)
backplane interfaces· 2 x GbE (base fabric), 2 x GbE or
1 x XAUI (fat pipe)
on-board· add/drop multiplexer· TDM cross bar· TDM-to-iTDM interworking· Xilinx Kintex-7 for data processing· optional up to 8000 HDLC controller
Multi CoreMulti Core
The MicroTCA Concept VI by N.A.T. | www.nateurope.com
Also available as Starter Kit
NAMC-xE1/T1Cost efficient AMC providing 8 or 16 E1/T1 line interfaces including TDM cross connect and I-TDM interworking in mid- or full-size form factor.
front panel interfaces· 8 E1/T1 (mid-size) or 16 E1/T1 (full-size)
backplane interfaces· 2x GbE, and optional PCIe on-board· TDM cross connection, TDM to I-TDM
interworking
Ch
assi
s an
d P
ow
er M
od
ule
s
NAMC-QorIQ-P5020NAMC-QorIQ-P5020-V6Powerful dual-core packet processing engine with the 64-bit, e5500 core built on Power Architecture technology, frequencies scalable to 2.2 GHz designated for today’s packet oriented applications like LTE or VoIP, optio-nally with a high-performance customizable FPGA.
front panel interfaces· 1x GbE, 1x USB, 1x RS232
backplane Interface· fat pipe: PCIe, SRIO, or XAUI· base fabric: 2x GbE, 2x SATA
on-board· QorIQ P5020· Xilinx Virtex-6 FPGA or Lattice ECP3
NAMC-QorIQ-P4080NAMC-QorIQ-P4080-V6Powerful octal-core packet processingengine built on eight Power Architecturee500mc cores - operating at frequencies upto 1.5 GHz in mid-size form factor, designated for applications requiring extensive multi-processing resources optionally combinedwith a free programmable data path engine.
front panel interfaces· XAUI (SFP+), 1x GbE, 1x USB, 1x RS232
backplane interfaces· fat pipe: PCIe, SRIO, or XAUI· base fabric: 2x GbE
on-board· QorIQ P4080· Xilinx Virtex-6 FPGA or Lattice ECP3
Multi CoreM
edia
Pro
cess
ing
NAMC-ODSP-MMulti-purpose media resource board in mid-size form factor for video and voice acceleration and transcoding with onboard CPU and 10GbE switch.
front panel interfaces· Status LEDs: 8 DSPs, 2x GbE, 2x XAUI, CPU, 2x user
backplane interfaces· 2x GbE, 2x XAUI, TCLKA-D, IPMI
on-board· 8 DSP (OCT2224M)· 512MB DRAM per DSP· Xilinx Kintex-7 incl. MicroBlaze core (Linux)· GbE/XAUI switch (VSC7448)· Stratum 3 PLL
Car
rier
s
NAMC-PMCA single-width, mid- or full-size AMC carrier for one PMC module.
key features· usage of standard off-the-shelf
PMC boards in MTCA environments· deployment of a rich variety of available
PMC modules· extension of PMC product life cycle
Exte
nd
ers
NAMC-EXT-RTM/-PSNAMC-EXT/-PSBoth extender kits provide a versatile tool to speed up the development process and to troubleshoot AMC cards within an ATCA or MTCA environment.
features· wire bridge for management and payload power
measurements· test pads for backplane and RTM signals· pads to connect JTAG equipment
variants· NAMC-EXT-RTM-PS and NAMC-EXT-PS offer an
additional on-board 3.3V power supply for stand-alone operation of AMC
NATIVE-R5size · 5U table top, depth: 373.3 mm
slots· 7 double AMC + µRTMs: 6 mid-size, 1 full-size· 1 full-size MCH + RTM
power supply · 110-240VAC, 600W output· -48VDC, 420W or 840W output· +24 VDC, 300W or 600W output
cooling units· 4 fans for AMCs and 2 fans for µRTMs backplane configuration· direct SATA / SAS connections· single star base fabric and fat pipe,
PICMG compliant· p2p connections at AMC
ports 12-15 (MTCA.4)· trigger, clock and
interlock signals
Also available as Starter Kit
NATIVE-R9size· 9U 19” rack-mounted, depth: 373.3 mm
slots· 12 single/double width mid-size AMCs + µRTMs· 2 MCH + RTM· JTAG switch module (JSM)
power supply· up to 4 power modules· 110-265VAC, 600W or 1000W output, or· -48VDC, 420W or 840W output· +24 VDC, 300W or 600W output
cooling units· 2 redundant hot-swap fan trays for AMCs + µRTMs
backplane configuration· direct SATA / SAS connections· dual star base fabric and
fat pipe, PICMG compliant· p2p connections at AMC
ports 12-15 (MTCA.4)· trigger, clock and
interlock signals
NATIVE-R2size· 2U 19” rack-mounted, depth: 378.0 mm
slots· 5 double width mid-size AMCs + µRTMs· 1 double full-size AMC· 1 double full-size MCH+RTM· 1 double or single full-size PM· 1 mid-size JTAG switch module (JSM)
power supply· 110-240VAC, 600W output· -48VDC, 420W or 840W output· +24 VDC, 300W or 600W output
cooling units· single push
backplane configuration· base + fat pipe fabric (AMC ports #0+1, #4-7 +
#8-11 to MCH)· p2p connections at AMC ports 12-15 (MTCA.4)· trigger, clock and interlock signals
Multi Core
The MicroTCA Concept VI by N.A.T. | www.nateurope.com
NAT-PM-AC600 / AC600D / AC1000N.A.T. power modules offer power conversion from a single 110-265VAC input source to 16 independent 12V channels for payload power and 3.3V for manage-ment power.
size· full size (6 HP), single or double width
key features· output power: 600W (AC) / 1000W (AC)· optical load indicator· redundancy support of N+1 and 2+2· 16 channels of 12V @ max. 6.6 A / 3.3V
@ 180 mA max.· support of 12 AMCs, 2 CUs, 2 MCHs
with individual control of management and payload power
· input power: single 110-265VAC· supportsfieldupgradesthroughHPM· Shared Management Power (SMP)
Intelligent Security System· output overvoltage and -temperature protection· input undervoltage shutdown· output short circuit protection· IEC/EN/UL60950-1 safety standard compliant· programmable current limiting threshold
per output channel
SDR
Bas
eban
d P
roce
ssin
g
Pow
er M
od
ule
sJT
AG
NAMC-ODSP-WExtremely high integrated AMC for SDR (Software Defined Radio), including RF frontend, baseband-processing and network layer processing resources.
size· AMC mid-size, single width form factor
front panel interfaces· 4x antenna Rx / 4x antenna Tx· front GPS antenna input to internal GPS module· alternative Dual SFP Connector on Faceplate for
CPRI Link to external RF
backplane interfaces· backplane port 2/3 for CPRI link to external RF· backplane port 4-7 for RF data exchange
via 10G Ethernet or CPRI
on-board · 2x DSP Octasic OCT2224W· 2x RF-SoC Analog Devices AD9361
on separate PCB· alternative RF Interface· FPGA Xilinx Kintex-7 XC7K160T· 2x NXP LS1043 for L2/L3 processing· GbE Switch Broadcom BCM5396· Flexible Clock Subsystem· IPMI based board supervision
NAMC-ZYNC-FMCAMC module featuring a Xilinx ZYNQ®-7000 FPGA and an FPGA mezzanine card (FMC) slot. It is designed for data acquisition, processing applications and computing nodes. The ZYNQ-7000 FPGA provides the software programmability of an ARM®-based processor with the hardware programmability of an FPGA, enabling key analytics and hardware acceleration while integrating CPU, DSP, ASSP, and mixed signal functionality on a single device.
size· mid-size, single width
front panel interfaces· dual UART-USB to ARM core and MMC· other connection depend on FMC module used
backplane interfaces· full AMC TCLKA-D and FCLKA connectivity· dual 1GbE connect to Port 0 and Port 1 · dual x4 (x8 for PCIe) to Fat-Pipe-Region
Ports 4-7 and Ports 8-11· any combination of PCIe, SRIO, XAUI
(on request)· extended: Ports 12-15 routed to FPGA
(2 x 4 LVDS)
on-board· Xilinx ZYNQ-7000 XC7Z045 or XC7Z100 FPGA · high pin-count FMC slot complies with VITA 57.1· dual banks of DDR3 memory
(1 GB 64-bit, 512 MB 32-bit) · 256MBNORquadSPIflashmemory· MicroSD card slot· AMC.1, AMC.2, AMC.3 and IPMI 2.0 compliant· JTAG access over backplane
The MicroTCA Concept VI by N.A.T. | www.nateurope.com
NAT-PM-DC420 / DC840 /DC300-LV / DC600-LVHigh density, high efficiency power modules (PM) for MicroTCA applications. Supplying 840W is the market’s most efficient PM to run today’s complex communication systems using latest processor generations with large memory capacity and an increased number of Advanced Mezzanine Cards (AMC).
MicroTCA low-voltage DC/DC Power Modules providing 300W or 600W to complement the extensive N.A.T. PM-family.
size· full size (6 HP), single width
key features· 16 channels of 12V @ 6.6 A max and 3.3V @
180 mA max.· optical load indicator· redundancy support of N+1 and 2+2,
load sharing (DC420 / DC840) – N+1 (DC300-LV / DC600-LV)
· output power: 420W (single brick) or 840W (dual brick) / 300W / 600W
· input power: dual -48VDC (DC420/DC840) / dual +24V (DC300-LV/DC600-LV)
· supportsfieldupgradesthroughHPI (DC420 / DC840)
Intelligent Security System· output overvoltage protection· input undervoltage shutdown· over temperature protection· output short circuit protection· built according to IEC/EN/UL60950-1
safety standard· programmable current limiting threshold per
output channel (DC420 / DC840)
NAT-JSMFlexible testing and diagnostic JTAG switch module to accelerate design, prototyping and operation of MicroTCA (MTCA) embedded computing systems.
size· single-width AMC module
front panel interfaces· JTAG Header: Xilinx compatible 14-pin
programming header at front panel· Mini-USB connector
backplane interfaces· TCP/IP · Backplane pin-out adaptable by onboard FPGA
on-board· power converter +5V to +12V · current draw not more than 200mA· subsystem processor: Altera Cyclone® III FPGA
5G, L
TE, U
MTS
, SD
R
NAMC-SDRSoftware defined radio (SDR) platform for developing, prototyping and testing 5G MIMO base station transceiver (BTS) systems and proprietary or standard implementa-tions of UMTS, LTE / LTE-Advanced systems, as well as a variety of applications ranging from cognitive radios to resilient security networks.
size· single full-size AMC
front panel interfaces· 4x 10 Gbps optical baseband interface
with QSFP connector· up to 8 antenna interfaces· 2x CLK · 1x 1Gb Ethernet interface· status LED
backplane interfaces· 2 x GbE, 1 x XAUI, TCLK A-D, IPMI
on-board· stacked digital interface card and radio
frequency front-end· 2, 4, 6 or 8 transceivers for Massive MIMO· CPRI compression technology enables up to 3x
effective bandwidth· up to 4x AD9361· ZYNQ XC7 Z045· DDR3 SDRAM· Flash· SD card
Syst
em M
anag
er
NATviewUser friendly graphic tool to view and control the components of the MicroTCA system – independent of any operating system.
key features· tree structured representation of sensor and actor · sensor value history, threshold setting, auto
update· intelligent alarm monitoring and prioritization· logging events, alarms· FRU (Field Replaceable Unit) editor· backplane connection viewer· HPM update manager· power manager
Make our expertise your solution - talk to us... we care.
N.A.T. GmbH i Konrad-Zuse-Platz 9 i 53227 Bonn i GermanyFon: +49 228 965 864 0 i [email protected] www.nateurope.com
N.A.T. was founded in 1990 with the aim of developing high-performance net-work solutions. From the beginning the goal has been to base these on an individ-ual combination of hardware and software modules. Constant growth during the last 25 years and substantial knowledge in networking technologies has brought N.A.T. to the forefront of the embedded and (tele-)communications market.
About N.A.T. (Network and Automation Technology)
Telecommunication · solutions from simple to complex· redundancy· low latency· optimized for converging networks· TDM-Packet interworking
Defence & Aerospace · longevity· ruggedized· conduction cooled· field replaceable· bandwidth from 1Gbps to 30 Gbps
Medical · low latency· multi-cluster· multi-graphic
Transportation · multi-cluster· high speed graphics· robustness
Let Your Application benefitopen standard | no single vendor lock-in
N.A.T. MicroTCA Concept © 2016 N.A.T. GmbH. All rights reserved. All other brands or names are property of their respective holders. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of N.A.T. GmbH. All data is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. N.A.T. and the N.A.T. logo are registered trademarks of N.A.T. GmbH.
Car
rier
Hu
bs
MicroTCA Carrier HubCentral management and data switch (GbE, XAUI, SRIO, PCIe) with clock distribution and generation in compact- or mid- or full-size form factor as well as single or double width
base-board· central mgmt. for 1-13 AMCs, 2 CUs, 1-4 PMs· e-keying, redundancy, load sharing· on-board or external carrier and shelf managers· layer 2, non-blocking, low latency GbE switch,· supporting VLAN, port base rate control and RSTP
(Rapid Spanning Tree Protocol)clock mezzanine· either on-board Stratum 3/3E type PLL,
supporting GPS and telecom frequencies· sourceofclockreferenceconfigurablefromeither
on-board PLL or any of the 12 AMC or from an external clock via the front panel connectors
· White-Rabbitfat pipes switch mezzanine including uplinks· SRIO (Gen2)· PCIe (Gen3)· 1GbE and 10GbE (XAUI)software support· configurationviawebbrowserorCommandLine
Interface (CLI) or scripting· Javabasedvisualization,configurationand
update tool NATview · remote management support· comprehensive debug supportfront panel interfaces· 2x GbE links supporting port trunking· 2 clock connectors (input or output)· 2 fat pipe uplinks (CX4, SFP+, optical x16 PCIe)· status indicator LEDs for AMCs, CUs, and PMs· console interface via USB or RS232COM Express RTM support ( combined with double width MCH and PCIe hub module)
· supporting all standard type 6 COM Express modules
· one 2.5” or two half 1.8” SATA storage devices· x16 PCIe connection to PCIe hub module· 1x GbE connection to MCH switch,
1x GbE at front panel· 2x display port and 4x USB 3.0
interfaces at front panel
MicroTCA
energy medical communication
SoftwareServiceS
defenSe&aeroSpace
induStrialcontrol
automation infotainment tranSportation