Wheeled Suction Pool Cleaner - Davey Water · pool or when opening your pool for the season. 3.2 Pool preparation Before installing the Davey Maverick, your pool should be clean and

Please pass these instructions on to the operator of this equipment.

ATTENTION:Please refer to www.bit.ly/DWPMAVIOI for any product information updates, or simply scan this QR code.

Wheeled Suction Pool Cleaner

Installation and Operating Instructions

Maverick™

2

Maverick™

Wheeled Suction Pool CleanerCongratulations on your purchase of a high quality, Davey Maverick. All components have been designed and manufactured to give trouble free, reliable operation.

Contents:

1. PRIOR TO USING THE SYSTEM, YOU MUST ENSURE THAT ..................................................................3

2. YOUR NEW SYSTEM ...................................................................................................................................3

3. INSTALLATION..............................................................................................................................................3

4. ADVANCED SETTINGS ................................................................................................................................7

5. MAINTENANCE ............................................................................................................................................8

6. TROUBLESHOOTING ................................................................................................................................11

7. SPARE PARTS ............................................................................................................................................13

8. WARRANTY ................................................................................................................................................15

3

1. PRIOR TO USING THE SYSTEM, YOU MUST ENSURE THAT...1.1 This manual contains important information that will help you in operating and maintaining the Davey

Maverick. Please retain it for future reference. Before installing the Davey Maverick, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Consult your place of purchase with any questions regarding this equipment. Alternatively refer to your local Davey representative via the contact details at the end of this manual.

ATTENTION: Do not play with cleaner or hose or apply to body. It is possible to trap and tear hair, or body parts. Hose can trip or entangle swimmers which could result in drowning. If your pool has a dedicated suction port (“vac port”) for vacuuming or for an automatic pool cleaner, it must be covered when not in use. To reduce the risk of injury, do not let children use or play with pool cleaner. Do not allow swimmers in the pool while the Davey Maverick is operating. Hose can trip or entangle swimmers which could result in drowning. Moving parts may injure hands or fingers. Stop pump before attempting to clean out the Davey Maverick head.IMPORTANT: Stop pump before attempting to clean unit. Do not allow swimmers in pool while pool cleaner is operating.

2. YOUR NEW SYSTEM1. Davey Maverick body2. Hose float3. Threaded adaptor4. Reducer cone5. Regulator valve6. Elbow7. Flow gauge8. 11 section hose set using: 10 x standard hoses; and 1 x leader hose.

3. INSTALLATION3.1 Pre-Installation Check List

3.1.1. Before installing the Davey Maverick, review and understand all warnings and safety information in this guide. Failure to follow these instructions, or improper installation of the Davey Maverick can result in damage to the pool finish, or the vinyl liner, Davey Water Products disclaims any liability for repairs or replacement to any of these structures or components of the customer’s pool.

3.1.2. Before installing the Davey Maverick in a vinyl liner pool. Check liner closely for signs of deterioration or damage from age, chemicals, pool wall damage, etc. If any damage is found, have a qualified pool professional make all the necessary repairs. Also, if there are stones, roots, etc., under the liner, remove them before installing the Davey Maverick. Before installing the Davey Maverick in a gunite pool (framework that is sprayed over with a concrete and sand mixture), or a pool that is partially, or completely tiled. Repair loose tiles and tighten any loose light rings.

1

REBEL™ Suction Side Pool Cleaner Installation and User’s Guide

POOL PREPARATION

1. Rebel cleaner body2. Hose float 3. Threaded Adaptor4. Reducer Cone5. Regulator valve6. Elbow7. Flow gauge8. Hose Set – 11 Sections

-10 Standard Hoses

-1 Leader Hose

Cleaner Components Remove the cleaner and all parts from the box. Check to be sure all components are included.

Pool PreparationBefore installing the Rebel™ Suction Side Pool Cleaner, your pool should be clean and algae-free so as to not inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:

1. Chemically balance the pool water.2. Brush pool and let the debris settle.3. Hand vacuum thoroughly.4. Clean filter and pump strainer basket.

1.

2.

Standard Hose

Leader Hose

8.

Figure 1

7

5 4

6

3

Figure 2.1

4

3.1.3. Before installing the Davey Maverick, clean your filter system. Make sure you have cleaned the filter, including backwashing, rinsing, and emptying all baskets. A clean system is necessary for proper cleaner operation and coverage.

3.1.4. Before installing the Davey Maverick, understand cleaner coverage. The Davey Maverick is designed to rid your pool of debris in approximately 4-6 hours. Less time could be needed, depending on the pool size. The Davey Maverick was not designed to automatically clean steps or swim outs or to work under a solar cover. It was also not designed to do initial clean up for a new pool or when opening your pool for the season.

3.2 Pool preparation

Before installing the Davey Maverick, your pool should be clean and algae-free to not inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:

• Chemically balance the pool water; • Brush pool and let the debris settle; • Hand vacuum thoroughly; and • Clean filter and pump strainer basket.

3.3 Assembling the Davey Maverick

The Davey Maverick body is shipped as one piece, making cleaner assembly a simple and quick process.

3.3.1. Hose assembly

For best results and to maintain proper operation, use only original Davey Maverick™ parts and hoses.

• To connect the hose sections, wet the ends in the pool water, then twist and push the female ends onto the male ends. See figure 3.1.

Figure 3.1

Male Hose End Female Hose End

• Connect the leader hose to the cleaner swivel. See Figure 3.2.

Figure 3.2

LeaderHose

SwivelAssembly

5

• Note: The leader hose is 305mm (12 inches) in length and shorter than the other sections included in the hose set. The leader hose is also marked with a red sticker. Failure to use this leader hose section will hinder cleaner performance.

• The hose should reach from where the cleaner is connected to the farthest point of the pool, plus one section and the leader hose.

• Install the hose float onto the second length of hose. The float should be placed 508mm (20 inches) above the cleaner. See Figure 3.3.

Leader Hose

SwivelAssembly

20 in(50.8 cm)

Hose must reach fur thest point in pool — —plus one length

plus leaderhose

Figure 3.3

20 in(50.8 cm)

• Make sure that all connections are snug.

• The overall length of hose needed will be determined by the distance from the point at which you attach the hose to the suction port to the furthest point in the pool, plus one length and the leader hose. Refer to Figure 3.4.

Leader Hose

SwivelAssembly

20 in(50.8 cm)


plus leaderhose

Figure 3.4

3.3.2. Skimmer box fitment

• Turn off the pool pump; • Close the main drain; then • Connect the hose to the skimmer vac plate as per instructions overleaf:

6

Figure 3.5 Figure 3.6 Figure 3.7

Waterco skimmer box Screw in the threaded adaptor from the top of the skimmer plate.

Poolrite skimmer box Screw in the threaded adaptor from the bottom of the skimmer plate.

Quiptron skimmer box Screw in the threaded adaptor from the top of the skimmer plate.

3


INSTALLING THE CLEANER

Different brands of skimmer boxAttach; Skimmer Adaptor Cuff into skimmer plate, then attach Adjustable Regulator Valve & 90 Degree Elbow to skimmer plate. Then connect one end of submerged hose into the 90 Degree Elbow.

90 Degree Elbow

Adjustable Regulator Valve

Skimmer Adaptor Cuff

Waterco Skimmer BoxScrew in the threaded adaptor from the top of the skimmer plate

Poolrite Skimmer BoxScrew in the threaded adaptor from the bottom of the skimmer plate

Quiptron Skimmer BoxScrew in the threaded adaptor from the top of the skimmer plate

Standard Installation1. Turn the pool pump off.2. Close the main drain.3. Connect the hose to the skimmer vac plate as per below instructions:

3




90 Degree Elbow







3




90 Degree Elbow







• Attach; Skimmer Adaptor Cuff into skimmer plate, then attach Adjustable Regulator Valve & 90 Degree Elbow to skimmer plate, figure 3.8 Then connect one end of submerged hose into the 90 Degree Elbow.

3




90 Degree Elbow







Figure 3.8

3.3.3. Adjusting flow to the cleaner with the flow gauge

• Turn the pool pump off. • Disconnect the Davey Maverick from the leader hose and connect the flow gauge in its place. Note: Make sure the hose remains submerged to prevent suction of air. • Turn the pump on. • Turn the regulator valve adjustment knob clockwise to increase flow or counter clockwise to decrease flow, until the disc indicator in the flow gauge settles between “Maximum” and “Minimum” flow. See Figure 3.9.

Figure 3.9

7

• Turn the pool pump off and remove the flow gauge and reconnect the Davey Maverick. • Lower the Davey Maverick into the pool and allow it to drop to the pool floor. • Turn the pool pump on.

3.3.4. Calculating cleaner speed (RPM) without the flow gauge

If you do not have the flow gauge originally included with your cleaner, following the steps below will allow you to calculate the cleaner speed and adjust RPM as needed.

• While the cleaner is running, bring the cleaner up to just beneath the pool’s water surface. Note: Be sure to keep the cleaner submerged while the pump is operating. This prevents the cleaner from pulling air into the pool system.

• Count the number of full rotations made by the wheel over a period of one minute. The number of rotations will give you the revolutions per minute; or RPM’s. An easy way to be sure you are counting full rotations is by counting the number of times the wheel hump passes by the swivel assembly.

• For proper performance, the Davey Maverick operates between 11-13 RPM. If the RPM is below 11 adjust the regulator valve (rotate adjustment knob clockwise) and repeat steps 1-2 until the RPM falls back into the optimal range. If the RPM is higher than 13 adjust the regulator valve (rotate adjustment knob counter clockwise) and repeat steps 1-2 until the RPM falls back into the optimal range.

3.4 AFTER installing the Davey Maverick

Make sure the Davey Maverick is operating correctly. The Davey Maverick may need some minor adjustments to make sure it is operating properly so there is no damage to the pool finish. Certain vinyl liner patterns are particularly susceptible to surface wear, pattern removal, ink rubbing off, or serious scratches to the pattern caused by objects coming into contact with the vinyl surface, including automatic pool cleaners. Davey Water Products is not responsible for any pattern removal, abrasions or markings on vinyl liners.

4. ADVANCED SETTINGS After installation, turn the pool pump on. The Davey Maverick should be moving about the pool at a rate of

2.5-3.5 metres per minute. Be sure to check each of the following initial adjustments.

4.1 Hose length

The pump must be on when you check the hose length. The hose contracts when the pump is operating and will be longer when the pump is off. While the Davey Maverick is operating:

• Position the Davey Maverick at the furthest point of the pool from where it’s attached. Use a pool pole and brush to easily position the Davey Maverick in the pool. • The hose should be long enough to reach the end of the pool, plus one hose section and the leader hose, see Figure 4.1.

Leader Hose

SwivelAssembly

20 in(50.8 cm)


plus leaderhose

Figure 4.1

• Remove any excess hose lengths from the middle of the hose assembly. This will ensure you do not alter the position of the hose float. • Save extra hose sections for use as needed for replacement. Note: Turn pool pump off when adding or removing hose sections.

8

4.2 Eyeball diverter positions

Position an eyeball diverter (not included) to redirect the return line water flow so it does not interfere with the Davey Maverick movement, see Figure 4.2. Try different positions to see which works best in your pool:

• Flow directed along the side of pool (the tile line). • Flow directed downward. • Flow directed against the hose will help steer the Davey Maverick away from obstructions such as stairs and ladders.

After installing the eyeball diverter, turn the pool pump on. The Davey Maverick should begin moving across the pool floor vacuuming up debris in its path.

5


CLEANER ADJUSTMENTS AND OPERATION

After installation, turn the pool pump on. The Rebel™ Suction Side Pool Cleaner should be moving about the pool at a rate of 2.5-3.5 metres per minute. Be sure to check each of the following initial adjustments.

Hose LengthNote: The pump must be on when you check the hose length. The hose contracts when the pump is operating and will be longer when the pump is off.

While the cleaner is operating: 1. Position cleaner at the furthest point of the

pool from where it’s attached. Use a pool pole and brush to easily position the cleaner in the pool.

2. The hose should be long enough to reach the end of the pool, plus one hose section and the leader hose. See Figure 12 .

3. Remove any excess hose lengths from the middle of the hose assembly. This will ensure you do not alter the position of the hose float.

4. Save extra hose sections for use as needed for replacement. Note: Turn pool pump off when adding or removing hose sections.

Figure 12

Hose must reach furthest point in pool — —plus one length

plus leaderhose

Eyeball Diverter PositionsPosition the diverter opening to redirect the return line water flow so it does not interfere with the cleaner’s movement. Try different positions to see which works best in your pool:• flow directed along the side of pool (the tile line).• flow directed downward.• flow directed against the hose will help steer the cleaner away from obstructions such as stairs and ladders.

After installing the eyeball diverter, turn the pool pump on. The cleaner should begin moving across the pool floor vacuuming up debris in its path.

BEFORE ADJUSTMENT

AFTER ADJUSTMENT

TOP VIEW SIDE VIEW

TOP VIEW SIDE VIEW

Figure 13Figure 4.2

5. MAINTENANCE The Davey Maverick requires almost no maintenance. Visually inspect your cleaner from time to time to

make sure that:

• The turbine is moving freely and is not obstructed by debris. See “Removing Debris from the Turbine” below. • The tires are not excessively worn, see Figure 6.4.

We recommend that you leave the Davey Maverick in your pool, except during chemical shock treatments.

• During swimming it is easy to unplug the Davey Maverick and pull it to one side. • Note: When storing the Davey Maverick, do not coil the hose. Lay the hose flat in an area protected from direct sunlight.

This Davey Maverick hose is specially designed to ensure optimum performance. Should replacement be required, insist on genuine Davey Maverick hose.

5.1 Removing debris from the turbine

• Be sure the pool pump is off. Remove the Davey Maverick from the pool and disconnect the Davey Maverick from the leader hose. • Check to see if anything is clogged inside the Davey Maverick. Do this by positioning the Davey Maverick with the buckle facing you and attempt to rotate the right side wheel forward. If the wheel rotates smoothly there probably is no obstruction. If it won’t rotate there is an obstruction. • Place the Davey Maverick on a flat work surface. Open the buckle on the front of the Davey Maverick by pulling it out and down. Lift the front of the top cover up and then firmly pull it forward. This will separate the top cover from the Davey Maverick body and you will now be able to lift the top cover straight up from the Davey Maverick body, see Figure 5.1. Set the cover aside. Note: The top cover is designed to fit tightly so you may have to wiggle it a little.

9

Figure 5.1Top Cover

Right Side Wheel

Buckle

Removal of Top Cover

• Pull the turbine cover straight up and off the Davey Maverick body. Set the turbine cover aside. See Figure 5.2.

Figure 5.2

SwivelAssembly

TurbineCover

Swivel Assembly and Cleaner Internals

• Remove any visible obstructions from the turbine and turbine cover. • Replace the turbine cover with the swivel assembly oriented towards the front of the Davey Maverick, see Figure 5.2. • Visually inspect the rest of the Davey Maverick and remove any debris that may be in the gears, drive shafts, swivel assembly, etc. • Repeat step 2 (turning the right wheel) to ensure that the Davey Maverick runs smoothly. • Place the top cover over the swivel assembly. • Place the tabs on the back side of the top cover into the slots on the back side of the Davey Maverick body (see Figure 5.3). Once these tabs are seated in the slots the front of the cover will fall into place.

Figure 5.3

Cover Tabs and Corresponding Body Slots

• Lock the top cover onto the Davey Maverick™ body with the locking buckle on the front of the Davey Maverick.

10

5.2 Tyre replacement

After prolonged use it may become necessary to replace the Davey Maverick rubber tyres. When the tyre surface has worn into the tyre’s grooves the tire is in need of replacement, see Figure 5.4.

5.2.1. To remove the Davey Maverick tyre:

• Turn the pool pump off and remove the Davey Maverick from the pool. • Disconnect the Davey Maverick from the leader hose. • Place the Davey Maverick on a flat work surface and fold the tire off of the wheel from top to bottom. Note: Remove the tyre by hand. Using other objects (screwdrivers, Allen keys, etc.) to remove the tyre may damage the wheel.

Figure 5.4New Tyre: Outer surface of the tyre is well above the bottom of the tyre’s grooves.

Excessively Worn Tyre: Outer surface of the tyre has nearly worn to the bottom of the tyre’s grooves.

Tyre wear comparison

5.2.2. To install the replacement tyre:

• Place the Davey Maverick on a flat work surface and seat the top of the rubber tyre onto the top of the wheel. Be sure that the back lip of the tyre is resting flat on the inside edge of the wheel. Note: Replace the tyre by hand. Using other objects (screwdrivers, Allen keys, etc.) to replace the tyre may damage the wheel.

• Stretch the bottom of the tyre over the bottom of the wheel. Be sure that the back lip of the tyre is resting flat on the inside edge of the wheel.

• Fold the back lip of the tyre onto the back of the Davey Maverick wheel along the entire Davey Maverick wheel. The tyre should lie flat on the top surface of the wheel.

11

6. TROUBLESHOOTING Because of the individual characteristics of your pool, some additional adjustments may be required to get

the best performance from your Davey Maverick. Use the following information to resolve possible issues.

PROBLEM CORRECTIVE ACTIONS

Davey Maverick is not moving or is moving too slowly.

Check flow with flow gauge included or by calculating the Davey Maverick RPM and adjust the flow if necessary, using the regulator valve, see section 3.3.3 and 3.3.4. If the Davey Maverick is being used in conjunction with a variable speed pump, it maybe necessary to run the pump faster.

Check for debris inside the Davey Maverick itself, see section 5.

Check to be sure the pump has primed. Check for leaks in the system that may prevent proper priming.

There may not be enough flow through the system. The filter may need backwashing.

Check to be sure that the main drain and all suction lines are closed, except for the suction line to which the Davey Maverick is attached.

Check for obstructions in the system (e.g. debris in the filter, pump basket or pump impeller).

Pool pump and filter system may be too small to provide proper water flow. Consult your pool professional.

Davey Maverick right wheel will not turn when rotated by hand Check for obstructions inside the Davey Maverick itself, see section 5.

Davey Maverick stays in one end of the pool

Check flow with flow gauge included or by calculating the Davey Maverick RPM and adjust the flow if necessary, using the regulator valve, see section 3.3.3 and 3.3.4. If the Davey Maverick is being used in conjunction with a variable speed pump, it may be necessary to run the pump faster.

Check the return line water flow and redirect as necessary with the included eyeball diverter, see section 4.

Check that hose is long enough to reach the furthest point in the pool, see section 4.

Check for proper hose float placement. The float may be in the wrong position, see section 3.3.

Be sure that the swivel assembly (at top of Davey Maverick) rotates smoothly. If not, the swivel assembly may be dirty and require cleaning.

Davey Maverick climbs the wall too much or climbs out of pool

Check flow with flow gauge included or by calculating the Davey Maverick RPM and adjust the flow if necessary, using the regulator valve, see section 3.3.3 and 3.3.4. If the Davey Maverick is being used in conjunction with a variable speed pump, it may be necessary to run the pump slower.

12

Davey Maverick won’t climb the pool walls

Check to be sure that the Davey Maverick tyres are not excessively worn, see section 5.2. Excessively worn tyres will not provide the grip necessary for your Davey Maverick to climb pool walls.

Check flow with flow gauge included or by calculating the Davey Maverick RPM and adjust the flow if necessary, using the regulator valve, see section 3.3.3 and 3.3.4. If the Davey Maverick is being used in conjunction with a variable speed pump, it may be necessary to run the pump faster.

Check to be sure that the leader hose has been installed and is in the correct location, see section 3.3.


Davey Maverick stays on the main drain

Check to be sure that main drain is closed. May need assistance from a pool professional.

Check to be sure a main drain grate is installed.

Davey Maverick falls on its side and takes too long to recover


Check to be sure that the leader hose has been installed and is in the correct location, see section 3.3.

Check that the hose is long enough to reach the furthest point in the pool, see section 4.

The return eyeball fittings may be pushing the Davey Maverick hoses away, see section 4.

13

7. SPARE PARTS7.1 Exploded diagram

A: Includes… 18, 19, 20, 21, 22 and 23 B: Includes… 4, 5, 6, 7, 8 and bearings

1

1

2

4

5

5

4

6

6

7

8

22

18

21

20

19

23

7.2 Spare parts listing

ITEM NOTES DESCRIPTIONQTY

REQ’D PART NO.1 Top cover kit 1 4036582 Buckle kit 1 4036594 Wheel kit (pair) 1 4036605 Tyre kit (pair) 1 4036616 Wheel hub kit (pair) 1 403657- A Accessory kit 1 40366222 Hose float 1 403663- Standard hose 1m 10 403664- Leader hose 1 4036655 Optional tyres large hump (pair) 1 403666- B Tune Up Kit 1 4036675 Optional tyre kit tiled pool (pair) 1 403668

14

8. WARRANTYDavey Water Products Pty Ltd (Davey) warrants all products sold will be (under normal use and service) free of defects in material and workmanship for a minimum period of one (1) year from the date of original purchase by the customer as marked on the invoice, for specific warranty periods for all Davey products visit daveywater.com.

This warranty does not cover normal wear and tear or apply to a product that has:• been subject to misuse, neglect, negligence, damage or accident• been used, operated or maintained other than in accordance with Davey’s instructions• not been installed in accordance with the Installation Instructions or by suitably qualified personnel • been modified or altered from original specifications or in any way not approved by Davey• had repairs attempted or made by other than Davey or its authorised dealers• been subject to abnormal conditions such as incorrect voltage supply, lightning or high voltage spikes, or damages from

electrolytic action, cavitation, sand, corrosive, saline or abrasive liquids,

The Davey warranty does not cover replacement of any product consumables or defects in products and components that have been supplied to Davey by third parties (however Davey will provide reasonable assistance to obtain the benefit of any third-party warranty).

To make a warranty claim:• If the product is suspected of being defective, stop using it and contact the original place of purchase. Alternatively, phone Davey

Customer Service or send a letter to Davey as per the contact details below• Provide evidence or proof of date of original purchase• If requested, return the product and/or provide further information with respect to the claim. Returning the product to the place of

purchase is at your cost and is your responsibility.• The warranty claim will be assessed by Davey on the basis of their product knowledge and reasonable judgement and will be

accepted if:o a relevant defect is foundo the warranty claim is made during the relevant warranty period; ando none of the excluded conditions listed above apply

• The customer will be notified of the warranty decision in writing and if found to be invalid the customer must organise collection of the product at their expense or authorise its disposal.

If the claim is found to be valid Davey will, at its option, repair or replace the product free of charge.

The Davey warranty is in addition to rights provided by local consumer law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For any internet connected products the consumer is responsible for ensuring a stable internet connection. In the event of a network failure the consumer will need to address the concern with the service provider. Use of an App is not a substitute for the User’s own vigilance in ensuring the product is working to expectation. Use of a Smart Product App is at the User’s own risk. To the fullest extent permitted by law Davey disclaims any warranties regarding the accuracy, completeness or reliability of App data. Davey is not responsible for any direct or indirect loss, damage or costs to the User arising from its reliance on internet connectivity. The User indemnifies Davey against any claims or legal actions from them or others relying on internet connectivity or App data may bring in this regard.

Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the products. The repair of your products may result in the loss of any user-generated data. Please ensure that you have made a copy of any data saved on your products.

To the fullest extent permitted by law or statute, Davey shall not be liable for any loss of profits or any consequential, indirect or special loss, damage or injury of any kind whatsoever arising directly or indirectly from Davey products. This limitation does not apply to any liability of Davey for failure to comply with a consumer guarantee applicable to your Davey product under local laws and does not affect any rights or remedies that may be available to you under local laws.

For a complete list of Davey Dealers visit our website (daveywater.com) or call:

® Davey is a trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2020.

NORTH AMERICAPh: 1-877-885-0585Email: [email protected]: daveywater.com

AUSTRALIAHead Offi ce6 Lakeview Drive,Scoresby, Australia 3179Ph: 1300 232 839Fax: 1300 369 119Email: [email protected]: daveywater.com

NEW ZEALAND7 Rockridge Avenue,Penrose, Auckland 1061Ph: 0800 654 333Fax: 0800 654 334Email: [email protected]: daveywater.com

EUROPEZAC des Gaulnes355 Avenue Henri Schneider69330 Meyzieu, FrancePh: +33 (0) 4 72 13 95 07Fax: +33 (0) 4 72 33 64 57Email: [email protected]: daveywater.com

MIDDLE EASTPh: +971 50 6368764Fax: +971 6 5730472Email: [email protected]: daveywater.com

Davey Water Products Pty LtdMember of the GUD GroupABN 18 066 327 517

15

® Davey is a trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2020.

NORTH AMERICAPh: 1-877-885-0585Email: [email protected]: daveywater.com

AUSTRALIAHead Offi ce6 Lakeview Drive,Scoresby, Australia 3179Ph: 1300 232 839Fax: 1300 369 119Email: [email protected]: daveywater.com

NEW ZEALAND7 Rockridge Avenue,Penrose, Auckland 1061Ph: 0800 654 333Fax: 0800 654 334Email: [email protected]: daveywater.com

EUROPEZAC des Gaulnes355 Avenue Henri Schneider69330 Meyzieu, FrancePh: +33 (0) 4 72 13 95 07Fax: +33 (0) 4 72 33 64 57Email: [email protected]: daveywater.com

MIDDLE EASTPh: +971 50 6368764Fax: +971 6 5730472Email: [email protected]: daveywater.com

Davey Water Products Pty LtdMember of the GUD GroupABN 18 066 327 517

* Installation and operating instructions are included with the product when purchased new. They may also be found on our website.

DWP1734-1

Documents

Wheeled Suction Pool Cleaner - Davey Water · pool or when opening your pool for the season. 3.2 Pool preparation Before installing the Davey Maverick, your pool should be clean and