Vibroacoustic Control Isolation

Abat Marcet 41-4308173 Sant Cugat (Barcelona)

Tel. 93 583 61 08 - Fax 93 675 58 [email protected]

Vibroacústica, control y aislamiento, S.L.

VibroacousticControl

Isolation

vibroacoustical solutions

www.vibcon.es

Abbreviated catalog2nd edition

ANGEL

Cuadro de texto

r.2 March-2.011

Our aim is to create vibroacoustical solutions in orderto keep noise and vibration transmission under control.If such transmissions are not taken into consideration,they may cause disturbances in people, machinerymalfunction and structural building damage.

Good vibrations ...on the internet


www.vibcon.es

Tableof contents

Vibcon, good vibrations ................................................................... 2Technical assistance service ......................................................................... 3Vibration and structural noise problems ...................................................... 3Vibroacoustic engineering services .............................................................. 4Vibration studies for evaluation and inspection .......................................... 5Main works and facilities ................................................................................ 6Vibcon’s main sectors of activity ................................................................... 7Vibroacoustic products and solutions .......................................................... 8

Our products ................................................................................................ 9Spring steel isolators ...................................................................................... 10

Series: MINIVIB / VIB 100 ........................................................................................................... 10Series: VIB 100 / VIB 1.000 ........................................................................................................ 12Series: VIB 4.000 / VIB 20.000 .................................................................................................... 14Series: VIB 40.000 / VIB 60.000 / VIB 80.000 ............................................................................. 16Series: MEGA 100 / MEGA 200 ................................................................................................. 16

Spring steel isolators for suspension ........................................................... 18Series: VIB MC / MINI TVIB ........................................................................................................ 18Series: TVIB 100 / TVIB 1.000 / Isophonic AC-rubber washer .................................................. 20

Rubber absorbers for suspension (Series: TGOM / GOM) .................................. 22Toothed antivibratory mats (Series: AD 412 / PAD 416 / 424 / 230) ........................... 22Isolating rubber plates (Series: GOMASOLA / GOMAELAS) .................................... 24Rubber absorbers (VIB PA Series) ....................................................................... 24Multipad (MULTIPAD series) .................................................. ............................... 24Aantivibratory supports (Series: VIB SPA / VIB SP) .............................................. 26Reinforced neoprene supports ...................................................................... 26Elastic supports (Serie VIB SB) ........................................................................... 28Silentblocks .......................................................................................................... 28

VIB SC series ............................................................................................................................. 28BIGOM / VIB SD series .............................................................................................................. 30VIBCON S series ........................................................................................................................ 32

Elastic armored supports (VIB SBL series) ........................................................ 32Antivibratory sleeves (Series: MS / MD / MDR) ...................................................... 34Banches of concrete ........................................................................................ 36

BA-DISCONTINUOUS / BA-CONTINUOUS .............................................................................. 36BA-MODULAR BENCH / BA-ECOBAN / BA-SELF-ELEVATING ............................................... 38

Melallic benches ............................................................................................... 40Series: VIB 1.000 BL and BZ / TR 2.100 .................................................................................... 40Series: TR 1.000 / SPR-MULTIPAD (mini bench) ....................................................................... 42

Vibroacoustic isolation for elevators .............................................................. 44Acoustic solutions ............................................................................................ 46

Acoustuic plate MA / Absorber sheet LA / Gomflex / Acoustic PC doors ................................... 46Cabins and acoustic screens / Rentangular mufflers SR ............................................................ 48

1

Technical assistanceservices

The added value of our vibroacoustical solutions is thesignificant amount of technical assistance and engineering theyimply.

In the first stage we analyze the technical and economicalparameters of 'the problem' and visit in situ the installation ormachinery to be studied.

We define and develop the most effective solution either fromour normalized solutions, or ad hoc, always complying with allcurrent legislation (Spanish Technical Building Code CTE, RITEupdated in 2.007, EN81-1 concerning lifts, Labor Risk Preven-tion, etc.) In the process we supply our client with data sheetcontaining all the information required for his particular application.

We also develop special solutions based on projects from ourengineering department.

Together with our client, we check the viability of the solutionuntil we obtain his final approval.

Vibcon Dynamometer laboratory

problemsVibration and structural noise

We act as consultants for problems arising on starting upmachinery for the first time, or facilities already in use wich havedeveloped problems.

We pay technical visits to our clients in order to observe problemsin situ and subsequently write technical reports with technicalsolutions.

We provide our client with the most suitable vibroacoustic solutionin every case.

Serving architects,engineers and maintenance

& production departments

3


2

...”Good vibrations”We have believed in itsince the very beginning

We continuously make every effort to get closerto installation, maintenance and designer ex-perts. Our aim is to cover new requirementsand legal specifications for vibroacoustic comfortin buildings and installations, as well as issuesregarding labor risk prevention.

This commitment means we areconstantly working on improving ourservices and products, in particularour increasingly personalized cus-tomer service

We are currently working along thesame lines and consequently havenot only created more and novel vi-

broacoustic solutions suited to new technicalrequirements (Spanish Technical Building Code"CTE", 2007 RITE, but we have also doubled ourefforts to extend our engineering services.

Our vibroacoustic engineering department isnow equipped to assess, carry out vibroacousticinspections of installations and buildings, anddesign and finally certify implementation of ourprojects.

We are sincerely grateful to our clients andprofessionals from various sectors for theirpermanent support in developing new solutionsin the field of vibroacoustics.

Vibroacousticalengineering services

Our Engineering department can carry out noise and vibrationprojects based on independence and impartiality criteria and ourinternal quality procedures.

Industrial and Architectural Acoustic Projects.applied to activities, facilities, building industry and labor riskprevention.In order to find the best solutions to vibroacoustic problems, weuse our own noise and vibration measurement equipment, wichis tested annually by an authorized laboratory (according toSpanish regulations). In addition to equipment required, we havepos-tprocessing and simulation software that allows us to predictedresults.

Acoustic impact study of road and railway traffic in buildableareas.

Reports concerning acoustic quality in buildings.

Acoustic inspection of activities and facilities.

Noise control projects of outdoor machinery (barriers, enclosures,mufflers...)Noise control projects of indoor machinery (engine rooms)Acoustic reports to obtain first occupation licenses in buildingsor activity licenses in commercial activities.

Projects in factories based on Spanish regulation regarding noiseexposure of workers, Spanish Royal Decree 286/2006, and thehealth and safety protection of workers against risks relatedto noise exposure.

Noise exposure at work stations.Counter-measure projects to reduce sound levels in industrialenvironments.Acoustic maps of industrial areas.

4

Reports regarding compliance with current legislation

Local regulations(Municipal Ordinances)

Building foundations(DB SE-C of the Technical BuildingCode)

Exposure to vibration in workingplaces(Law 31/1995 of Labor RiskPrevention)

Vibc

on &

LEA

M U

PC

Vibration studiesfor evaluation and inspectionin installations, activities, buildingsand working places

5

Air-conditioning and ventilation sector.

Industrial cooling sector.

Pump installations.

Installation of elevators, hoists, pulley rooms...

Acoustic conditioning and isolation.

Compressors, generating sets...

Metal deformation machinery: eccentric presses, screw presses,forge hammers...

Metrology equipment.

Machinery for graphic arts: guillotines, rotary, offset machines...

Machinery to prepare or process food products: dough kneader,cutters, mincers...

Vibcon’smain sectors of activity


... good vibrations7

Main worksand facilities

INSTITUTE OF APPLIED AUTOMOBILE RESEARCH - IDIADA: Seismic slab design for theisolation of engine and wheel test benches.SANT CUGAT AUDITORIUM: Isolation of thermal installations and conduits around the wholestage house.LLEIDA AUDITORIUM: Isolation of thernal installations and conduits around the whole stage house.“EL PROGRESO” NEWSPAPER IN LUGO: Study and supply of seismic floating bench for rotatingvibratory isolation of 376 tonnes with bench included (2/96).UNIVERSITY OF OVIEDO - GEOLOGY DEPARTMENT: Study, design and manufacturing ofisolators for 250 kg electron microscope and subsequent supervision (5/96).ALEGI: Design and construction of low frequency isolators to suspend anechoic chamber, horizontalroom and vertical room of the laboratory (12/96-7/97).KURSAAL ROOM OF DONOSTIA: Study and design of special isolators for air conditioners forthe technical room of the Auditorium (1998).THEATRE “TEATRE LLIURE-CAMUNSA”: Design and construction of low frequency assemblymounted in series to isolate air-conditioning equipment close to the stage house (1/98).PUBLIMAIL AGENCY - GALDACANO (Bilbao) - LABEIN: Study of vibratory isolation for 50tonne HARTMAN 8 body printing machine (10-12/1999).SCHOOL OF MUSIC AUDITORIUM, BARCELONA: Design of floating bench and calculation andsupply of isolators for 16 tonne equipment (7/2002).KABALTER RECORDING STUDIO ELKARNALEAN - DONOSTIA: Desigm of 132 m2 floatingbench for “Coro Donostiarra” recording studio (2001).EIX MACIA MILLENIUM BUILDING, SABADELL: Pressure group and air-conditioning equipmentisolation (2001).LA CAIXA BUILDING SOCIETY, HEAD OFFICE, DIAGONAL, BARCELONA: Design of floatingbenches for pumps in basement -3.AUDITORIUM AND FORUM CONVENTIONS CENTRE 2001 - UTE INSTALLATIONS: Projectand supply of the entire antivibratory system for isolatinf pipe outlines, air conduits and thermalinstallation equipment.TORRE AGBAR BUILDING: Antivibratory assembly of benches and cooling plants on technicalfloors and in basement.MNAC NATIONAL MUSEUM OF CATALONIA: Study and engineering of antivibratory systemsfor installations.FIRA 2000-FIRA BARCELONA TRADE FAIR EXTENSION: Study of modular concrete benchesfor vibratory isolation of pressure groups.GRAN HESPERIA HOTEL - BARCELONA: Design of system for antivibratory suspension oflarge self-adjustable structures for technical room (2004).GRAN HOTEL MERIDIEN - BARCELONA: Study and design of construction solution to raiseand isolate bench set of 15 Tn pumps (2004).MNAC ART MUSEUM OF CATALONIA: Elastic system design for the stands of the Oval Room(2004); engineering services to assess vibration levels and design corrective actions (2005).FIRA - 2000 - L’HOSPITALET EXTENSION - BARCELONA: Design of vibration isolators forcovered cooling plants. Acoustic treatment of ventilation system (2005).TENERIFE AIRPORT EXTENSION: Study of air-conditioner vibration isolation, considering windload and other enviromental factors (2006).CIUDAD DE TELEFÓNICA CITY PROJECT - UTE AIR-CONDITIONING - MADRID: Vibroacusticsolution provision and technical support (2006).MENORCA AIRPORT EXTENSION: Study and design of 800 m2 of floating floor for coveredtechnical room (2007).BOEHRINGER INGELHEIM ESPAÑA, S.A. - SANT CUGAT: Slab vibration study of the productionplant affected by machinery (2006).BARCELONA AIRPORT EXTENSION - UTE ENERGY HEAD OFFICE: Study and design ofspecial elastic suspension for air conditioners. UTE - Energy Head Office (2007).MOSSOS D’ESQUADRA REGIONAL POLICE HEADQUARTERS - SABADELL: Study ofvibroacoustic solution for cooling plants.TORRE ESPACIO, BUILDINGS S and V (BUSSINES AREA TOWERS - CTBA) - MADRID: Study,design and supply of floating benches for large pressure groups. Design of elastic expanders forpiping (2007).FMC FORET - LA ZAIDA (ZARAGOZA): Engineering services to prepare sound map for existingprocess plants (2007).CIUDAD JUDICIAL DE BARCELONA: Study, design and manufacturing of special supports forlarge covered air conditioners and air-conditioning equipment (2008).LLEIDA CONFERENCE CENTRE: Supporting study and design of full air-conditioning installationand floating benches (2008).LUZ ALBA LABORATORY (SINCROTRÓN) CERDANYOLA B-30: Engineering services to assessvibration levels in accordance with Cells’ specifications. Design of vibration isolation solutions forall air-conditioning equipment (2008).

6

Our products

Spring steel isolators

Low and medium frequency:Series VIB 1.000 and MEGA.

Very low frequency: VIB macro series.

For elastic suspension of pipes, machinery and ceiling structures.

Absorbers

Ruber antivibratory mats:PAD system (patented models).

Suporting metal rubber absorbers:Vibcon SPA (patented model).

Isophonic rubber washers for vibroacustic isolation of fan-coiland conduit fixation systems.

GOMASOLA rubber plates by the meter. Smooth rubber platesfor thermal isolation, dielectric insulation of machines and pipingin buildings.

Floating benches

Modular floating slabs of concrete.

Accessories to make floating benches using metallic springisolators: angles for welding to bench sides, special angles,leveling and precompression systems, etc.

Acoustics materials

Self-adhesive absorbing sheets to absorb plate noise in airconduits.

Acoustics plates for isolating noise emitted by installationmachines.

Cabins, screens and acoustics mufflers.

Accesories

Acoustic bases for metallic spring isolators that improvevibroacoustic performance when supported directly on a fullyfloating hearth without a bench.

Set of screws, fixation elements, leveling and support to facilitateantivibratory assembly.

For further technical information, request our technicaldocumentation (TD) or technicals files (TF) specifically

designed for each model and/or product.If you are uncertain regarding which solution to implement,

please request our application files (AF).

Vibroacustic productsand solutions

Products manufactured and marketed with the Vibcon brand arebased on the following principles:

Exclusive attention to clients to define the most efficient technicaland economical solution.

Efficient supply service and post-sale attention.

Extensive technical documentation available to clients, regardingproducts, assembly and placing of standardized and specialproducts.

Highly-qualified technical work team with a wide range ofexperience.

Continual search for vibroacustic solutions and their improvement.As a result, all standardized product series have a large rangeof supply versions, ensuring that the greatest number of solutionsproposed for an installation can be implemented.

UNE EN ISO 9001:2000 Quality System. Guarantees the qualityof manufacturing processes and services, compliance with currentlegislation and professional commitment of the team at Vibcon.

8

Design and assembly of products manufactured by Vibconare our own, and our commitment is to carry out R+D+I tomake creation of new products our strong point.

235810

1,21,21,21,21,2

15255075

100

1212121212

3 - 145 - 2310 - 4515 - 6820 - 90

MINIVIB 15 2TMINIVIB 25 2TMINIVIB 50 2TMINIVIB 75 2TMINIVIB 100 2T

235810

1,21,21,21,21,2

15255075

100

1212121212

3 - 145 - 2310 - 4515 - 6820 - 90

MINIVIB 15 TMINIVIB 25 TMINIVIB 50 TMINIVIB 75 TMINIVIB 100 T

VIB 100 series

0,523581013

2,32,32,32,32,32,32,3

515255075

100125

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

Static load in [daN] and deflection in mmSpringsteelisolators

0,523581013

2,32,32,32,32,32,32,3

515255075

100125

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

0,523581013

2,32,32,32,32,32,32,3

515255075

100125

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

235810

1,21,21,21,21,2

15255075

100

1212121212

3 - 145 - 2310 - 4515 - 6820 - 90

MINIVIB series

T 2T

S

10

Dimensions in mm / Assembly Description / Applications:

Description:

Metallics steel isolators indicated to isolate all types ofmachinery with work regimen of over 1000 rpm and dynamicequipment from 2 kg.Natural frequency 11-5 Hz.

Description:

Metallics steel isolators indicated to isolate all types ofmachinery with work regimen of over 800 rpm and dynamicequipment from 1 kg.Natural frequency 9-4 Hz.

2T

S

T

Supply versions: vertical clearance in mmVIB100 S 70VIB100 B 72VIB100 BB 73

The nonslip mat is standard. It you can supply,on demand, special vibroacoustic mat.

11

S

B

BB

Model

MINIVIB 15 SMINIVIB 25 SMINIVIB 50 SMINIVIB 75 SMINIVIB 100 S

VIB 005 S

VIB 015 S

VIB 025 S

VIB 050 S

VIB 075 S

VIB 100 S

VIB 125 S

VIB 005 B

VIB 015 B

VIB 025 B

VIB 050 B

VIB 075 B

VIB 100 B

VIB 125 B

VIB 005 BB

VIB 015 BB

VIB 025 BB

VIB 050 BB

VIB 075 BB

VIB 100 BB

VIB 125 BB

Description / Application / Supply versions:

Alternative supply version:

Additionally, ecological zinc coated can be supplied

M-8

M-8

VERY IMPORTANT:for isolate machinery with elevated inertia you shouldconsider wind effects. Consult our technical department.

Static load in [daN] and deflection in mmSpringsteelisolators

VIB 005 T

VIB 015 T

VIB 025 T

VIB 050 T

VIB 075 T

VIB 100 T

VIB 125 T

0,523581013

2,32,32,32,32,32,32,3

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

0,523581013

2,32,32,32,32,32,32,3

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

VIB 100 series

VIB 1.000 series 1013152025304050607080

2,52,52,52,52,52,52,52,52,52,32,3

100125150200250300400500600700800

2525252525252525252323

20 - 9225 - 11530 - 13840 - 18450 - 23060 - 27680 - 368100 - 460120 - 552140 - 641160 - 732

1013152025304050607080

2,52,52,52,52,52,52,52,52,52,32,3

100125150200250300400500600700800

2525252525252525252323

20 - 9225 - 11530 - 13840 - 18450 - 23060 - 27680 - 368100 - 460120 - 552140 - 641160 - 732

12

T 2T

B

BB

Dimensions in mm / Assembly Description / Supply versions:

Description:

Metallics steel isolators indicated to isolate all types ofmachinery with work regimen of over 800 rpm and dynamicequipment from 1 kg.Natural frequency 9-4 Hz

Supply versions: vertical clearance in mmVIB100 T 71VIB100 2T 71

2TT

Supply versions: vertical clearance in mmVIB1000 B 113VIB1000 BB 115

Description / Supply versions / Accessories:

Description:

Metallic steel insulators of low frequency with superficialepoxy-type plastic protection. Indicated to isolate machinerywith a work regimen of over 600 rpm.Natural frequency 7-3 Hz.

13

515255075

100125

515255075

100125

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

Model

VIB 005 2T

VIB 015 2T

VIB 025 2T

VIB 050 2T

VIB 075 2T

VIB 100 2T

VIB 125 2T

VIB 1.100 B

VIB 1.125 B

VIB 1.150 B

VIB 1.200 B

VIB 1.250 B

VIB 1.300 B

VIB 1.400 B

VIB 1.500 B

VIB 1.600 B

VIB 1.700 B

VIB 1.800 B

VIB 1.100 BB

VIB 1.125 BB

VIB 1.150 BB

VIB 1.200 BB

VIB 1.250 BB

VIB 1.300 BB

VIB 1.400 BB

VIB 1.500 BB

VIB 1.600 BB

VIB 1.700 BB

VIB 1.800 BBThe nonslip mat is standard. On demand, a specialvibroacoustic mat can be supplied.

Accessories:


Additionally, ecological zinc coated can be supplied.

B BB


Additionally, ecological zinc coatedcan be supplied.

M-8

M-8

M-12

187

210

117

83

M-12

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

Springsteelisolators

VIB 4.060

VIB 4.080

VIB 4.100

VIB 4.150

VIB 4.200

VIB 4.250

VIB 4.300

VIB 4.350

VIB 4.400

VIB 4.450

VIB 4.500

VIB 5.625

6

8

10

13

20

25

30

35

40

45

50

63

2,3

2,3

2,3

2,3

2,3

2,3

2,3

2,3

2,3

2,3

2,3

2,3

60

80

100

150

200

250

300

350

400

450

500

625

23

23

23

23

23

23

23

23

23

23

23

23

12 - 54

16 - 72

20 - 90

26 - 117

40 - 180

50 - 225

60 - 270

70 - 315

80 - 360

90 - 405

100 - 450

125 - 563

VIB 4.000 series

VIB 20.000 series

14

145

77

158

M-10

Dimensions in mm Description / Supply versions / Assembly:

Descripción:

Insulators formed(trained) with 4 metallic springs combinedin parallel with lateral shielding, which limits insulatorbalancing, and a interior sheet of rubber that muffles rubbing.Indicated to isolate all kinds of machinery sensitive to lateraldisplacement with regimen of work over 800 rpm anddynamic equipment from 13 kg.Natural frequency 9-4 Hz.

15

20

23

25

28

30

35

40

45

50

55

60

70

80

90

100

110

120

140

150

160

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,3

2,3

2,3

200

225

250

275

300

350

400

450

500

550

600

700

800

900

1000

1100

1200

1400

1500

1600

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

23

23

23

40 - 184

45 - 207

50 - 230

55 - 253

60 - 276

70 - 322

80 - 368

90 - 414

100 - 460

110 - 506

110 - 552

120 - 644

140 - 736

160 - 828

200 - 920

220 - 1012

240 - 1104

280 - 1281

300 - 1373

320 - 1464

Static load in [daN] and deflection in mm

Assembly (VIB 4.000 and VIB 20.000 series):

Assembly with M-12leveling screw

Direct assembly

Model

VIB 20.200

VIB 20.225

VIB 20.250

VIB 20.275

VIB 20.300

VIB 20.350

VIB 20.400

VIB 20.450

VIB 20.500

VIB 20.550

VIB 20.600

VIB 20.700

VIB 20.800

VIB 20.900

VIB 21.000

VIB 21.100

VIB 21.200

VIB 21.400

VIB 21.500

VIB 21.600

Description:

Insulators consisting of a nounting in parallel of 2 antivibratorysprings. Natural frequency from 7 to 3 Hz.

- vibroacoustic mat for inferior base+ leveling screw

- Nonslip mat- Finished with epoxy protection- Leveling screw

Accessories (VIB 20.000 + BA):



Description / Supply versions / Assembly / Accessories:



MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad


40

45

50

55

60

70

80

90

100

110

120

140

160

180

200

220

240

250

280

300

320

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,5

2,3

2,3

2,3

2,3

400

450

500

550

600

700

800

900

1000

1100

1200

1400

1600

1800

2000

2200

2400

2504

2800

3000

3200

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

25

23

23

23

23

80 - 368

90 - 414

100 - 460

110 - 506

120 - 552

140 - 644

160 - 736

180 - 828

200 - 920

220 - 1012

240 - 1104

280 - 1288

320 - 1472

360 - 1656

400 - 1840

440 - 2024

480 - 2208

501 - 2304

560 - 2576

600 - 2760

640 - 2944

VIB 40.000 series

Static load in [daN] and deflection in mm Dimensions in mm Description / Supply versions / Accessories

Description:

The VIB 40.000 insulators are parallel assemblies of 4antivibratory wharves.Natural frequency from 7 to 3 Hz.

16 17

Model

VIB 40.400

VIB 40.450

VIB 40.500

VIB 40.550

VIB 40.600

VIB 40.700

VIB 40.800

VIB 40.900

VIB 41.000

VIB 41.100

VIB 41.200

VIB 41.400

VIB 41.600

VIB 41.800

VIB 42.000

VIB 42.200

VIB 42.400

VIB 42.500

VIB 42.800

VIB 43.000

VIB 43.200

VIB 60.000VIB 80.000 series

Description:

Insulators consisting of assembly in parallel of 6 (VIB 60.000) and 8(VIB 80.000) vibration-proof springs.Natural frequency from 7 to 3 Hz.

For greater loadscheck information of our models:

Insulators formed by 6 or 8 wharves, designed for transmission isolationof vibrations in large machinery and very heavy equipment andstructures.

Suitable for isolating all kinds of machinery with low-cycle regimens ofwork (over 600 rpm).

VIB 60.000 and VIB 80.000 series



Assembly with vibroacoustic matand leveling.

- Vibroacoustic mat for inferior base + leveling screw- Nonslip mat- Finished with epoxy protection- Leveling screw

Accessories:

Assembly and accessories:

See VIB 40.000 series

Assembly:

Assembly with M-16leveling screw

Direct assembly

M-16

172

166

212

117

6

VIB 60.000 VIB 80.000M-16 M-16

20406080

100120140

1,51,51,51,51,51,51,5

200400600800

100012001400

15151515151515

40 - 18080 - 360120 - 540160 - 720200 - 900240 - 1080280 - 1260


MEGA 100 seriesMEGA 200 series

New series

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

3-13 mm

10203040506070

1,51,51,51,51,51,51,5

100200300400500600700

15151515151515

20 - 9040 - 18060 - 27080 - 360100 - 450120 - 540140 - 630

Static load in [daN] and deflection in mmModel

MEGA 220

MEGA 240

MEGA 260

MEGA 280

MEGA 2.100

MEGA 2.120

MEGA 2.140

MEGA 110

MEGA 120

MEGA 130

MEGA 140

MEGA 150

MEGA 160

MEGA 170

Dimensions in mm Description / Applications / Supply versions:

Description:

Insulators of a wharf with great horizontal inflexibility withregard to the vertical. They are lower in height than theprevious series.Natural frequency from 11 to 6 Hz.

Applications:

- Presses- Electricity-generating groups- Elevators- Transformers ...

Metallic steelisolatorsfor suspension

1

3

5

10

1

1

1

1

10

10

10

10

2 - 9

5 - 23

10 - 45

20 - 90

10

25

50

100

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad


VIB MC 10

VIB MC 25

VIB MC 50

VIB MC 100


Additionally, ecological zinc coated can be supplied.

VIB MCseries

18

Description

Description:

This is the smallest pier inulator on the market. Ideal formounts where there is little space to suspend machinery.Allows placement through standardized lane metallic. Theconical geometry conical gives great lateral stability. Thisenables insulators, once placed, to remain aligned withoutendangering the mechanical stability of the mounting andmaintains correct gripping.

19

MINI TVIB series1

3

5

10

10

1

1

1

1

1,2

10

10

10

10

12

2 - 9

5 - 23

10 - 45

20 - 90

20 - 90

15

25

50

100

100

MINI TVIB 15

MINI TVIB 25

MINI TVIB 50

MINI TVIB 75

MINI TVIB 100

Dimensions in mm

Description:

Metal pier insulators shorter than the original models VibconTVIB or TM dupes.The most remarkable advantage is its low height, thatmakes it suitable for facilities with evaporators, fan-coilsand other equipment that must be installed in confinedspaces as, for example, in the interior of false ceilings.

30

26

47,5

77

65

M-8

60

Ø 10

Ø 10

MEGA 100

MEGA 200

102,5

60

10,3

65

10131520253545

2,52,52,52,52,52,52,5

100125150200250350450

25252525252525

20 - 9225 - 11530 - 13840 - 18450 - 23070 - 32290 - 414

TVIB 1.100

TVIB 1.125

TVIB 1.150

TVIB 1.200

TVIB 1.250

TVIB 1.350

TVIB 1.450

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

Static load in [daN] and deflection in mmMetallic steelisolatorsfor suspension

0,52358

1013

2,32,32,32,32,32,32,3

515255075

100125

23232323232323

1 - 43 - 145 - 2310 - 4615 - 6920 - 9225 - 114

TVIB 100 seriesTVIB 1.000 series

20

Dimensions in mm Description

Description:

Series of steel spring metallic isolators specially designedto suspend machinery and conductions. Indicated forequipment and conduits located in critical zones and witha cycle for operation under 600 rpm.

21

Model

TVIB 5

TVIB 15

TVIB 25

TVIB 50

TVIB 75

TVIB 100

TVIB 125

New serie

1

3

5

10

1

1

1

1

10

25

50

100

10

10

10

10

2 - 9

5 - 23

10 - 45

20 - 90

TMC 015

TMC 025

TMC 050

TMC 100

Description

Description:

The TMC series work in afrequency of 5 Hz and ispatterned for suspendedwrought, fan-coils, pipes andacoustics roofs in publicplaces with demand for aheight level of vibroacousticisolation.

55

10

58

49

IsophonicAC-rubber washer

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad


Description

Description:

Isophonic rubber washersthat prevent the transmissionof vibroacoustic effects ofimpedance change.

6,58,58,5

10,512,516,5

222525303050

34856

15

Model Dimensions in mmDi De e

DiDe

e

TMCseries

80150

100

M-12

11

AC M6AC M8AC M8.8AC M10AC 12 x 30 x 5AC M16

TVIB 100

TVIB 1.000

TVIB 1.000

TVIB 100

Metallic steelisolatorsfor suspension

2

5

2

5

2

2

2

2

25

50

25

50

7

7

7

7

20

45

20

45

Rubber pads

P = pin for M-8

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad (4)

MAXIMUMDeflection

OPTIMUMLoad (3)

22

Dimensions in mm Description / Assembly

Description:

The series TGOM and GOM are designed for suspensionin slab fan-coils, pipes and acoustic ceilings in spaces ofpublic use.

10

10,5

55

49

56

4520

23

TGOM series

TGOM GOM

Static load (2) to compression in daN (1)

AD 412

PAD 230

PAD 416

PAD 424

112 0,5 1250 2,5 275 - 1125AD 212

MIN.Deflection

in mm

MAX.Load

(4)

Statical load (2) to compression in daN (1)

190 0,5 23000 3 2000 - 15000PAD 416

250 0,5 4000 5 500 - 3600PAD 424

20 1 1300 7 100 - 1100PAD 230

OPTIMUMLoad

(3)

Surfacepressurein kg/cm2

0,75 - 3

1,7 - 11

0,3 - 2,4

0,05 - 3,6

MAX.Deflection(4) in mm

Description:

AD 212AD 412 Series very versatile and multi-purpose in industrial mounts.

Surface pressure in kg/cm2; 0,75-3.

PAD 416 Activity system comprising 2 mats of AD412 fitted for the toothed face.This gives more than double load per unit area of a single ironantivibratory element. Surface pressure: 1,7-11 Kg/cm2.

PAD 424 Improves the degree of vibroacoustic isolation by moving. Therefore,it consists of two toothed small mats AD412 mounted in series. Thesame load capacity with a small toothed mat AD412 being doublereduces the frequency thus improving the degree of vibratory isolation.Surface pressure: 0.3-2.4 kg/cm2.

PAD 230 System of small vibroacoustic mats with an intermediate mattress ofair cells that provides exceptional additional physical properties ofinsulation against the low frequency sound in acoustic impacts andmechanical blows that arise from dissipative effects of generatedenergy.Surface pressure: 0.05-3.6 kg/cm2.

Cogged vibroacoustic edging. Request information.

Dimensions in mm

24388388

12AD 212

Dimensions in mm

194194

CBA

16PAD 416 388388

Model

33PAD 230 194194

PAD 424

A

B

C

Assembly

Direct assembly:placement of themachine on a matfor simple support.

Dressed assembly:holding with rubber.

Split assembly:to isolate thedifferent supportsof a machine.

Assembly:

Model

TGOM 25 P

TGOM 50 P

GOM 25

GOM 50

Model

New

Assembly:

The housing TGOMis articulated tofacilitate assembly.

12AD 412 388388

AD 412 450 0,5 5000 2,5 1100 - 4500 0,75 - 3

Notes: (1) : 1 daN = 1kgF(2) : The values of load have been obtained by means of dynamometric tests. In addition

they are exclusive for Vibcon products and therefore not comparable with any othermodels on the market.

(3) : The optimum work zone is thef linear behavior segment.(4) : Permissible overload + 50% fully factored load.

MIN.Charge

4070

100160

1,51,51,51,5

200400500800

6666

60-140105-300105-300150-400

PA 70 B

PA 70

PA 100 B

PA 100

VIB PA series

Dimensions in mm Description / Supply versions

Description:

Wads of rubber indicated for large weights that are veryeasy to place and which anticipate possible problems ofvibrations, avoiding direct contact of any equipment with asurface or construction component.

Adhesive versions :

PA 70 ADPA 100 AD

C

BA

D

30100100

30PA 70 B 7070CBA

30PA 70 7070

Model

30PA 100 100100PA 100 B

D

29

2929

29

Multipad

* 1 daN = 1kgF

Multipad

Minimum and maximum compression static load in daN*Model

10

640

1

1

100

6000

5

5

20 - 80

1280 - 5120

PA 50(1 tablet of 50 x 50)

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad

MAXIMUMDeflection

OPTIMUMLoad

MINIMUMCharge

MINIMUMDeflection

MAXIMUMLoad (4)

MAXIMUMDeflection

Static load (2) to compression in daN (1)OPTIMUM

Load (3)in daN

Dimensions in mm Description

Description:

The MULTIPAD incorporates notable innovations andadvantages with the known small antivibratory mats witha toothed face.

MULTIPAD combines the properties of the classic SPsupports + small toothed AD mats and, finally, the classicwads of PA rubber.

MULTIPAD is formed by 64 tablets of antivibratory rubberarranged in a matrix and mutually by means of an easilycuttable membrane, even by hand.

Multipad series

Elastic support:Mounting like an elastic support for ametallic structure or machine.

Rubberabsorbers

Assembly

Rubber antivibratory support:Mounting like an antivibratory support:MULTIPAD transforms into an antivibratoryrubber support by inserting a screw in thecentral orifice of each one of the tabletsthat, if hexagonal, are adapted at the head(top) of the screw.

MULTIPAD

400 mm

400mm

50 mm

50 mm

PA 50

Model

18 mm

Isolatingrubberplates

GOMASOLA

24

Dimensions in mm / Supply versions Description / Applications

Description:

They are used in facilities for the manufacture of pieces or profilesfor multiples uses:

Vibratory isolationDielectric isolationTo avoid thermal bridgesTo prevent contact of a metallic surface with soil, tus avoidingoxidation produced by rain waterTo compensate differencesDetach from the surface any point of support of a structureWaterproof in plates

25

GOMAELAS

Thickness Wide

3510202530

1.3001.3001.3001.3001.3001.300

111111

2 a 102 a 102 a 52 a 52 a 52 a 5

Hardness[°ShA]

Model

GOMASOLA

Stretching[%]

GOMAELAS

65

43

215

650

Patentedmodel

Supply versions:

Cut and cogged plates with suitable width andlength of 5 and 10 m can be supplied.

Notes: (1) : 1 daN = 1kgF(2) : Load values were obtained by means of dynamometric tests. In addition, these

are exclusive for Vibcon products and therefore not comparable any other modelson the market.

(3) : The optimum work zone is the linear behavior segment.(4) : Permissible overload + 50% fully factored load.

Norm. length Other lengths

Threaded version:with two differentmeasures.

Description:

The SPA absorbers are an adjusted PA 70 and PA 100absorbers. With this new patented version, PA rubber tabletsare transformed in antivibratory high-grade supports servicingclassic supports.

Vibration-proofsupports

VIB SPA series

Model

8 1 150 3,5 40 - 130SPA 50


20 1 620 5 170 - 480SPA 70

40 1 1000 5 80 - 880SPA 100

Dimensions in mm Description / Applications

M-12 749032

M-8 54SPA 50D

Dimensions en mm

5018CBA

M-10 74SPA 70 9032

Model

M-16 1049032M-12 104SPA 100 9032

26 27

Machine

Support beam

Assembly (SPA 50): Alternative supply versions:

Nivela version (leveling):provides support for groundmachinery with slopes toevacuate pluvialwaters.

VIB SP series

MINIMUMCharge

MINIMUMDeflection

in mm

MAXIMUMLoad

MAXIMUMDeflection

in mm

OPTIMUMLoad

SPA 150 60 1 1500 7 600 - 1100

M-16 156SPA 150 9033

The SPA 70 allows sure andresistant mounting whenelastic fixings are needed, orin cases of vibrations producedby sudden start-ups.

With the same form, each ofthe tablets Base PA 50 of aMultipad pad, are transformedinto the vibration-proof supportSPA 50 by means of theaccessories “Base PA 50” and“50 Base PA Nivela”.

Description:

Series designed for the elastic support of all kinds ofmachinery, both in facilities, workshops and productionlines.

Provides complete safety compliance for UNE ENV 1032machinery

Dimensions in mm Description / Applications

M-12 90SP 90D

Dimensions in mm

9030CBA

M-16 134SP 120 9541

Model

Description:The elastomer armed supports are used as structural components in buildings,civil works, railway infrastructures, machinery, storage warehouses, etc..

With correct specifications and installation they provide elastic support requiringno maintenance capable of providing uniform distribution of loads and natauraladaptation to structural movements. The interior armor prevents surfaceexpansion of rubber as there is no break load.

D

B

A

C

D

B

A

e3 mminternalsteel armor

Neoprene

Dimensions:According to the surface pressure requestedby the client and the dimensions of the supporthousing.

The supports are made by mold and thedynamometer value is 1,9 Tn.

Model

150 -- 850 -- 200 - 750SP 90


30 1 2100 6 200 - 1800SP 120

MINIMUMCharge

MINIMUMDeflection

in mm

MAXIMUMLoad(4)

MAXIMUMDeflection

in mm

OPTIMUMLoad (3)

B

A

C

DM D


they are exclusive for Vibcon products and therefore not comparable to any othermodels on the market.

(3) : The optimal work zone is the linear behavior segment.(4) : Permissible overload + 50% fully factored load.

Reinforcedneoprene supports

SC 35

SC 45

SC 60

SC 70

SC 90

SC 130

28 29

Dimensions in mm Description / Assembly

DM

Dimensions in mm

22324042

DCAModel

SB 64/67SB 104/107SB 154/157SB 254/257

IM-6

M-10M-14M-18

284580

128

60100150200

76124186240

Silentblocks

Description:

Series designed for elastic support of all kinds of machineryexposed to sudden horizontal displacements.

Provides full safety compliance for UNE ENV 1032machinery.

Assembly:

VIB SC series

Model

715206075

175

11

1,5222

37

10111314

15 - 6535 - 10040 - 25070 - 350100 - 650250 - 1200


MINIMUMCharge

MINIMUMDeflection

in mm

MAXIMUMLoad(4)

MAXIMUMDeflection

in mm

OPTIMUMLoad

in daN (3)

80125300400750

1500

Description

Description:

The absorbers of the SC series have more lateral inflexibilitythan those of the S series.

Application is universal in air-conditioning equipment whereit is desired to prevent excessive lateral displacement afterinstallation.

D

Dimensions in mm

233048586071

CBAModel

SC 35SC 45SC 60SC 70SC 90SC 130

DM20----------

M-8M-8

M-12M-12M-12M-16

3133607090

130

4042707999

140

D

DM

C

A

C

A

B

B

D

DM

Supply versions:1: SC 35 / 452: SC 60 / 130

1 2

PACK SC 35PACK SC 45

D

DM

I

A

C

DM

10

Elasticsupports

VIB SB series

Model

3

5

10

18

32

44

26

50

70

100

160

240

1

1

1

1

1

1

2

2

2

2

2

2

15

25

50

90

160

220

130

250

350

500

800

1200

3

3

3

5

5

5

8

8

8

9

9

9

5 - 12

8 - 20

15 - 40

27 - 72

48 - 130

66 - 180

39 - 110

75 - 200

105 - 300

150 - 400

240 - 650

360 - 1000

SB 64

SB 66

SB 67

SB 104

SB 106

SB 107

SB 154

SB 156

SB 157

SB 254

SB 256

SB 257


MINIMUMCharge

MINIMUMDeflection

in mm

MAXIMUMLoad(4)

MAXIMUMDeflection

in mm

OPTIMUMLoad (3)

Format of provision formed by the set of4 Silentbloks with its fixation screws.







New

Silentblocks

BIGOM seriesNotes: (1) : 1 daN = 1kgF

(2) : The values of load have been obtained by means of dynamometric tests. In addition,they are exclusive for Vibcon products and therefore not comparable to any othermodels on the market.


Model

2

1

1

1

56

26

3

3

10 - 40

5 - 20

BIGOM N

BIGOM G

Staticl load (2) to compression in daN (1)

MINIMUMCharge

MINIMUMDeflection

in mm

MAXIMUMLoad(4)

MAXIMUMDeflection

in mm

OPTIMUMLoad (3)

VIB SD series

Dimensions in mm / Quartering Description / Assembly

Description:

BIGOM is the most versatile absorber for vibratory isolationapplications with machines of small dimensions and amaximum weight of 200 Kgs.

Formed by two bodies of rubber which fit into each otherto adapt perfectly to the thickness of the metallic surfaces.It addition, permits isolation of fixing structures, acousticpartitioning, and angular fastening of conduits.

Assembly:

Patent model

30 31

Compression Shear

SD 20.19

SD 40.28

SD 60.44B

SD 60.44

SD 60.60

SD 80.70

SD 90.76

Model

12304075

150300400

2,55558

9,59,5

54,5561088

Physical analysis

MAXIMUMCharge

Deflectionin mm

MAXIMUMLoad

Deflectionin mm

32,5712307070

Load / Min. deflection = Load / Max. deflection x 0,2

Version 3

Description / AssemblyDimensions in mm / Supply versions

C

C

A

D

Version 2 A

B

Version 1

C

A

B

Description:

The geometry is in the shape of dolly, the absorbers of theSD series have great elasticity to the flexion (greater thanin the S series), making them very useful for equipmentthat requires isolation with a low dulling index.

Assembly:

SD20.19SD40.28SD60.44BSD60.44SD60.60SD80.70SD90.76

19284444607076

2,55558

9,59,5

20406060608095

M-6M-10M-8M-8M-10M-14M-16

A B C D

Dimensions in mmModel

26,85

26

37,55

26

27

Alernative supply versions:

compression (axial) shear (radial) compression- shear

Dimensions in mm / Supply versions

33

Description:

The VIBCON S series is an absorber of classic rubber -metal. It is universal, used for all kinds of elastic suspensionof machinery.

These absorbers can be used with both compression andshearing in engines, pumps, vibrators, and specially inequipment mounted on a metallic structure.

Description / Assembly

Assembly:

Version 1Metallic screw

at both extremities.

Version 2Metallic screw at one endand internal welding nut on

the inverse side.

Version 3Internal welding nutat both extremities.

Version 4 (Limit)Metallic screw at one

end and rubber base inthe inverse side.

D

A

C

B

BD

C

B

A

A

D

C

C

D

A

B

The S VIBCON series is supplied in 5 versionsdepending on fastening system:metallic screw, welding nut or rubber base.

Compressionassembly

(axial)

Shearassembly(radial)

compression - shearassembly

Version 5 (Limit)Internal welding nutat one end and rubberbase in the inverse side.

C

D

A

Description

Description:

Series designed for elastic support of all types ofmachinery with abrupt submissive horizontaldisplacements.

Provide full safety compliance for UNE ENV 1032machinery.

Base with four holes for standard fixation

L

I

LI

DMDC

A

Silentblocks

VIBCON S series

32

Compression Shear

810152025305060708090

120150150190200250300300350450500550600700800800

1000

3,534375

5,53,5853

106

111112119

14118

13119

13121613

2242

4,53,54

2,564

2,57,55,5129109715116,5159714101614

Physical analysis

1,51,52,52,54,55881111112020252530303035353540404060608080

Deflectionin mm

Deflectionin mm

S 13.20S 13.15S 15.20S 15.15S 20.30S 20.20S 25.22S 25.25S 30.30S 30.22S 30.15S 40.40S 40.28S 50.60S 50.45S 60.60S 60.45S 60.35S 70.70S 70.50S 70.35S 80.70S 80.50S 80.40S 90.75S 95.60S 105.100S 105.75

A B C D

10101212161620202020202525252525252525252535353545454545

M-5M-5M-5M-5M-6M-6M-8M-8M-8M-8M-8M-10M-10M-10M-10M-10M-10M-10M-10M-10M-10M-14M-14M-14M-16M-16M-16M-16

1313151520202525303030404050506060607070708080809595105105

Dimensions in mm

2015201530202225302215402860456045367050357050407560

10075

Model

Armoredelasticsupports

VIB SBL series

Dimensions in mm

A DCM-10M-10M-10M-12M-12M-12M-16M-16M-16

MIN.Charge

Deflec.in

mm

MAX.Load

Model Compressionstatic load in daN

111111111

70120180140200300360500800

333433666

Optimalarea

in daN

21-6036-9054-13042-10060-15090-230108-275150-375240-640

424242535353757575

323232363636606060

Deflec.in

mm DM747474929292124124124

I727272909090114114114

L909090114114114144144144

14243628406072

100160

SBL 704SBL 706SBL 707SBL 904SBL 906SBL 907SBL 1.204SBL 1.206SBL 1.207

Load / Min. deflection = Load / Max. deflection x 0,2

MAXIMUMLoad

MAXIMUMLoad

35

Description / Quartering

Description:

Antivibratory muffs indicated for the absorption/recovery ofdeformations in fluid conduction lines.

VIB MS

1. PN10 standardized bridles2. Body of neoprene and nylon weave3. Steel hoop DIN 172234. Reinforcement hoop

1. Smelthing bridle2. Smelthing nut3. Smelthing thread union4. Synthetic fiber5. ElastomerMaximum extension Maximum compression

Maximum cross-sectionaldeformation

Maximumangular deformation

VIB MDR

Extension - Compression / Deformation

Deformation:

Extension - compression:

VIB MD

L.MAX. L.MIN.

a°=15°

VIB MS / MD

123 4 5VIB MDR

1

2

3

4

MS 32

MS 40

MS 50

MS 65

MS 80

MS 100

MS 125

MS 150

MS 200

MS 250

MS 300

MS 350

MS 400

MS 450

MS 500

MS 600

Antivibratorymuffs

MS / MD / MDRseries

34

MDR 20

MDR 25

MDR 32

MDR 40

MDR 50

DN

Normal

Model Assembly length in mm

9595

105115130135170180205240260265265265265265

Max.extension

Max.comp.

1 3/4”1 1/2”

2”2 1/2”

3”4”5”6”8”10”12”14”16”18”20”24”

898999

107122122156167186221241246246246246246

9797

107118133140175185212247267273273273273273

9999

110121133145180190220254274281281281281281

888

10101212121222222222222222

878799

103118117152162180215235240240240240240

cross-sectional

DNModel Assemblylength

3/4”1”

1 3/4”1 1/2”

2”

200200200200200

2222222222

66666

200200200200200

200200200200200

Cross-sectionaldeformation

Angulardeformation

MD 40

MD 50

MD 65

MD 80

MD 100

MD 125

MD 150

MD 200

MD 250

MD 300

DN

Normal

Model Assembly length in mm

175175175175225225225325325325

Permissible deformation in mm

Minimum Maximum

1 1/2”2”

2 1/2”3”4”5”6”8”10”12”

137137137137187187187280280280

190190190190242242242342342342

205205205205260260260360360360

45454545404040353535

125125125125175175175265265265

VIB MS

VIB MD

VIB MDR

Max.extension

Max.comp.

Permissible deformation in mm

Minimum Maximum

cross-sectional

Axialcompression

Axialextension

Basic elements:

In floating benches we distinguish 3 basic elements:A. Machine object of isolationB. Inertial block that it will have to be measured depending

on the equipment.C. The elastic element that makes it possible to float the

inertial block

Vibcon has made diverse types of benches depending onthe type of machinery and emplacement.

BA(benchesof concrete)andBL(metallicbenches)

Basic elements Description

36 37

Applicable to the implementation of soils and floating benchesof large dimensions and high surface loads. The thicknessof the bench is 8 12 cm. In case of placement of covers inthe exterior it is necessary to construct a slope-levelingbench in advance.

AssemblyBA-DISCONTINUOUS

Benches of concrete (BA)Metallic benches (BL) S/UNE 100-153/2004

Properties:They lower the center of garvity and increase the dynamic stabilityThey diminish the extent of the vibration due to the internal contributionto the vibroacoustic montingThey improve the uniformity of weight distribution on antivibratorsThey reduce the effects of the exterior forces originated by vibrationsderiving from the wrought (passive vibrations)Geometric effect of absorption

Vibcon calculates and povides the different elastic elements (C)necessary for its implementation, including assembly instructions,installation (F-31 forms) and/or facultative direction.

Characteristics:They are poured concrete floated by means of PA70 or PA100 rubberplugs, distributed by the surface and forming a reticle measured accordingto the following parameters:

Dimensions of the machine or installationDistribution of point loads(charges)Admissible overload of crossbeam or slab that will sustain itDynamic characteristics of the machineNecessary requirements of vibroacoustic isolation

Vibcon will calculate and supply the different vibroacoustic elementsnecessary for its implementation, as well as the precise instructionsfor correct mounting. Once the bench or floating soil is built, ourtechnical department will check it.

BA-CONTINUOUS

PA 100 PA 70

1. Benche or floating soil2. Purbenches3. Slab

Characteristics:They are poured concrete floated by means of an elastic element placeduniformly along the surface that will form the bench. Models exist withthicknesses and specific densities. Parameter will be measured based onthe following:

Dimensions of the machine or installationDistribution of loadsAdmissible overload of sill or slab that will sustainDynamic characteristics of the machineAttenuation needed for fulfillment of the regulation

Applications

Vibcon will calculate and supply the different vibroacoustic elementsnecessary for its implementation, as well as the precise instructionsfor correct mounting. Once the bench or floating soil is built, ourtechnical department will check it.

Applicable for the implementation of floating benchesindividualized for every machine or group of small equipment.The thickness of the bench is from 8 to 12 cm. Useful alsofor floating soils by means of plates of fiber cement.

In case of placement inthe exterior of covers, itis necessary to contructa slope-leveling bench inadvance.

Bench execution

Purbenches

Compound3P-40

Purbenches 8050Purbenches 160203P-40

80160160

Density(Kg/m3)

502040

Thickness(mm)

Comp. load10-30% (Kg/m3)

150 - 350450 - 1500500 - 2000

Model

(BA) Banchesof concrete

1. PA (70/100)2. LR233-303. Polyethylene film4. Formwork5. Purbenches

39

Types of assembly Applications

Applications:

Groups of water pumps, condensing conditioned air units.

(BA) Benchesof concrete

BA - MODULARBENCHE

Characteristics:The Vibcon modular concrete benches have exclusive characteristicsdifferent from the previous types.

Autoambles are poured without need of placing concrete "insitu"This eliminates the time of plottingThey are leveled to adapt to the soil with earringsAfter raisinhthey allow of rain water in coversThey incorporate their own antivibratory assembly normalized by meansof SPA rubber absorbersIn case of re-exposure it can easily be relocate (.. it is removed andplaced)Several modular slabs can be joined to form a bench of large dimensionsdepending on equipment dimensions. (Linear or surface assemblies)

Modular with absorber SPA 70 M-10

Modular with isolators VIB 100

Modular benchwith absorbercompound

With SPA 70 M-10

With isolator VIB 100

With shock absorber compound

500 x 500 x 60

500 x 500 x 60

500 x 500 x 60

Dimensionsin mm

120

300

600

Max.load (Kg)

Naturalfrequency (Hz)

10,5

3,5

7,7

Types of assembly

Model patebted by I. Jackson

New

38

Characteristics:They are low frequency floating benches of (3-5 Hz) characterized by theelastic element being a wharf insulator inserted in a metal box placed inthe formwork and which, once placed, can be raised to the correct assemblyheight.

VIBCON will calculates and supply the different vibroacoustic elements for hisimplementation, as well as the precise instructions for correct assembly. Once thebench or floating soil is constructed, it is checked by our technical department.

Applications

Applications:

Applicable for the implementation of floating benches orfloating soils with high exigency regarding vibroacousticisolation.

NewBA - ECOBAN

ApplicationsCharacteristics:They are plates of rrecycled rubber useful for supporting floating benchmaterial and to prevent deterioration due to contact with rain water. Inaddition they can be used directly as benches for equipment of smalldimensions or point supports of floor-separation installations (props orsupports of horizontal or vertical pipeline). The jagged geometry alongone of its faces allows rain water to flow without altering the vibroacousticproperties of the elastic material.

Applications:

Applicable for the implementation of floating benchesindividualized for every type of machine or group of smallequipment.

Plate of 1 x 1 m

Reinforced concretebenches

Purbenches

ECOBAN 40/50

Ecoban 50Ecoban 40

Dimensions in mm

20

CA

ModelB

1520 4035 50

A

BC

weight (kg/m2)

Test ECOBAN 40

Extension %

Compressivestrenght (kg/m2)

Reduc. thickness %

5%

20%

ECOBAN 50

Values in kg/m2

2.200

10.800

60 70

1.300

9.800

24,5 26,2

BASELF-RAISING

New

VIB 1.000 BL and BZseries

40

Dimensions in mm / Assembly Description

Applications:

Benches for pressure groups, motorcycle-ventilators, alreadyinstalled equipment that needs to be separated from theground.

41

New series

Applications

Applications:

Suspension of heavy facilities for fluid conduction.

(BL) Metallicbenches For the implementation of metallic benches of machinery and VIBCON

facilities, a series of accessories and products that enable easyimplementation.

2,52,52,52,52,52,52,52,52,52,32,3

1013152025354550607080

2525252525252525252323

100125150200250350450500600700800

20 - 9225 - 11530 - 13840 - 18450 - 23070 - 32290 - 414100 - 460120 - 552140 - 641160 - 732

Model

VIB 1.100 BL/BZ

VIB 1.125 BL/BZ

VIB 1.150 BL/BZ

VIB 1.200 BL/BZ

VIB 1.250 BL/BZ

VIB 1.350 BL/BZ

VIB 1.450 BL/BZ

VIB 1.500 BL/BZ

VIB 1.600 BL/BZ

VIB 1.700 BL/BZ

VIB 1.800 BL/BZ

These series consist of insulators of the series VIB 1.000 B, but with theM-16 coil and the angular coil in the shape of a "Z" or an "L" as well asleveling and fixation crews of every model.From this form can be implemented normalized cogged metallic benchesand, later insulators can be placed depending on dimensions, loads andfrequency of the equipment.

VIBCON will carry out the calculations andmeasurement of benches, select the model and thenumber of units to be placed.Instructions for assembly will be attached.

Assembly:

By means of the M-16 screw leveler the benchcan be raised to the required height. Very usefulfor benches with functioning machinery andwhich needs to become free elastically withthe minimum of height (VIB 1.000 BL, from 5to 10 mm. And BZ, 30 mm.)

TR 2.100 series The models of this series are designed to suspend wrought combs ofwater pipelines, conduits and equipment which due to its dimensions andweight need to be installed with special supports, and which have significantlateral inflexibility, to prevent balancing at the time of the implementationof the assembly.Thus, a structure can be completely separated from the ground, preventingtransmission of vibration and structural noise.

2,3

2,3

2,3

2,3

2,3

2,3

2

3

5

8

10

13

23

23

23

23

23

23

15

25

50

75

100

125

3 - 14

5 - 23

10 - 45

15 - 68

20 - 90

25 - 113

Model

TR 2.030

TR 2.050

TR 2.100

TR 2.150

TR 2.200

TR 2.250

Dimensions in mm / Assembly

OPTIMUMLoad

MAXIMUMDeflection

MAXIMUMLoad

MINIMUMCharge

MINIMUMDeflection

OPTIMUMLoad

MAXIMUMDeflection

MAXIMUMLoad

MINIMUMCharge

MINIMUMDeflection

42

Dimensions in mm Applications

43

Serie TR 1.000

The models in this series are designed to suspend wrought combs of waterpipelines with larger point load values than with the TR 2.000 series, butwith the special particularity that facilitates implementation of supports, asthis permits immobilization of the eslastic action of the insulator.

2,52,52,52,52,52,52,52,52,52,32,3

1013152025354550607080

2525252525252525252323

100125150200250350450500600700800

20 - 9225 - 11530 - 13840 - 18450 - 23070 - 32290 - 414100 - 460120 - 552140 - 641160 - 732

Model

TR 1.100

TR 1.125

TR 1.150

TR 1.200

TR 1.250

TR 1.350

TR 1.450

TR 1.500

TR 1.600

TR 1.700

TR 1.800

New series

(BL) Metallicbenches

New

SPR-MULTIPAD 250Mini bench

Dimensions in mmDescription:

They are heigh-adjustable supports designed to elastically support machinesof large dimensions, with irregular and asymmetric geometry regardingthe distribution of point load support.

Adjustable height:

The SPR-MULTIPAD support is height-adjustable, which makes it possibleto compensate for area irregularities as well as earrings of slab in coveredfloor of buildings.This adjustment capability obviates construction of short columns or worksupports so machinery to be supported will remain at the same level.

Applications

Large air-conditioning units of one or two levels, refrigerationplants, etc.

Patented model

OPTIMUMLoad

MAXIMUMDeflection

MAXIMUMLoad

MINIMUMCharge

MINIMUMDeflection

ANGEL

Cuadro de texto

M-11

ANGEL

Línea

ANGEL

Línea

ANGEL

Cuadro de texto

M-16

Vibroacusticisolationfor elevators

Electromechanicalelevators

up / down machine

MTV series

44

cockingmechanisms

and frequencyvariators

for elevators

45

To avoid inconveniences of mechanical vibrations and structural noiseit is necessary to operate directly at the source, that is to say, at thegroup engine - elevator tractor.

Dimensions in mm Applications

To avoid the transitory (impulse)of start-up and stop, whichappears in the shape of structuralnoise, VIBCON MTV metallicinsulators are placed.

For this technical characteristicsand elevator levels are request forthe calculation of suppor treactions. This calculation is madefor an empty elevator, and for onewith maximum load (maximumnominal load).

For high-speed elevators withvibrations, the group of joint framecables of the frame and cabin areisolated. Depending on the typeof group, Vibcon will study andindicate the most suitable elasticjoint.

For every elevator a SETOF ASSEMBLY MTV isprovided with specificinflexibility for every supportincluding assemblyinstruction from F31.

Rigidity KAMTV-A

Cabin side

Rigidity KBMTV-B

Cabin side

Rigidity KCMTV-C

Counterbalanceside

Rigidity KDMTV-D

Counterbalanceside

Assembly

Elevator machine - up Elevator machine - down

Besides the group isolation of the engine - tractor of an electromechanicalelevator, another important area of mechanical vibration has to beconsidered that induces structural noise: the cocking mechanism panels.

Generally they are hung or supported rigidly, and therefore they mustbe isolated by means of properly calculated insulators.

Elastic supports are designed by means of MINIVIB-2T with angularnormalization to facilitate the assembly, or by means of another solutionadapted to the individual case.

The clamps of the guides normaly transmit vibration to housing when theelevator moves in the phases of ascent, descent or the transitory stop.

Viscoelastic materials designed to separate the abovementioned jointsfrom the ground and transmission of vibration is reduced to verticalparameters

Elevator guides

Assembly

VibconMINIVIB 2T

Assembly

Consult us for the isolation of hoist, hydraulic elevators, dumbwaiters,etc..

1. Rubber washerVibcon AC

2. Cogged GOMAELAS

3. Rubber sleeve

Cabin side

Cabin side

Absorber sheetLA

Applications

Acousticisolationsolutions

46

Characteristics Applications

47

Description:

The “acoustic compound MA” is a double-layer element consisting ofa high-density absorbing sheet (LA) glued to a sheet of cotton fibers andtextile impregnated with fire-proofed phenol resin.

5,6

5

7,6

Roll5 x 1 m

Roll6 x 1,05 m

Plates1,35 x 1,05 m

Model FormatWeightKg / m2

MA 55

MA 55 A(asphalt)

MA 75

Thickness(mm)

Acoustic plate MA

Description:

The “absorber sheets LA” of Vibcon are synthetic, of high density, witha polymer or asphalt base, that provide good damping of vibrating surfacesand therefore favor insulation and acoustic comfort of the diverse constructioncomponents.

Interior treatment of auto bodies and frames of machineryin general, for the noise isolation by vibranting surfaces.

Absorption conduits remove the air gap noise step. Thefibers, being of a textile nature, are not harmful as arefibrous mineral materials (rock wool, glass fiber ...).

Acoustic isolation of down pipes.

Acoustic isolation between housings.

12,5

18

14

High-level acoustic isolation.Easy to manipulate and adaptable to irregular surfaces.Resistant to cold and heat.Self-extinguishable.Excellent resistance to aging.

3,2

10

Adhesive roll6 x 1,05 m

Adhesive plate1,25 x 1,05 m

Model FormatWeightKg / m2

LA 6

LA 10

Thicknessmm

4

5,3

Characteristics

Sheet acoustically tight adhesiveGOMFLEX

Description:

The bands of acoustically tight material “GOMFLEX” have adhesive tapeon one side to facilitate union to a metallic profile or smooth surfaces ofany type of material.

Its particular advantage is acoustic tightness, as it adapts easily to anyclosing or joining profile, preventing any air gap, and thus the transmissionof air noise.

Characteristics

Cogged of 50 x 5 mm

Cogged of 50 x 10 mm

Cogged of 100 x 5 mm

Model Format

GOMFLEX 50-5

GOMFLEX 50-10

GOMFLEX 100-5

AcousticPC doors Description:

The "acoustic PC Doors" consists of exterior steel plate and interiorfilling of absorbents with superposed insulation.

The lock is made of injected duraluminium, with point of adjustment in thecenter of the door, thus ensuring equal surface pressure in the wholeperimeter

Characteristics

Rw = 47 dB

Rw = 50 dB

Rw = 44 dB y RF-90

Model leafs

PC 01

PC 02

PC 03

Acousticisolation

1 - 2

1 - 2

1 - 2

Acousticisolationsolutions

Cabins andacoustic screens

48

RectangularMufflers SR

Description:

Vibcon “Cabins and acoustic screens” are constructed from modularpanels of cold-laminated steel and lacquers, with the first layer of primingbeing epoxy with a thickness of 10 microns.The interior contains a filling of high-density protected by a black cloth toprevents its decomposition.

Description:

The “Rectangular Mufflers SR” reduce the noise of air duct flow inventilation and air-conditioning equipment as well as other machines thatrequire aeration systems. For this purpose air is channeled through parallelbaffles in such a way that the passage and length (L) condition passiveattenuation level since part of the sound energy is diminished into heat.

To implement this attenuating function, the baffles are manufactured usinginorganic and incombustible mineral fibers with high acoustic absorption.

49

Measured rectangular Mufflers SR

The parameters required for correct sizing of SR mufflers are:

1. The section dimensions of the equipment’s air duct (W x H).2. Air flow (m3/h) and maximum admissible load loss (mm. c.d.a.) of the equipment.3. Lenght “L” (mm) and air passage of baffles “P” (cm) to define the required attenuation.

600 mm900 mm

1200 mm1800 mm2100 mm2400 mm

Leng

ht L

(mm

)SR muffler attenuation in dB

F (Hz)P (cm)

125 250 500 1 K 2 K 4 K1061012202023

15 569121416

20355191212

10131825284550

159918263136

208913202626

10182738505050

15152332485050

20123025405050

10223546505050

15202936505050

20172532465050

10223245505050

15162530485050

20121926365050

10222635495050

1591521313642

2082015212828

Example: SR-15-1000 x 600 x 1200Vibcon Rectangular Muffler with air passage of 15 cm (P),section 1000 x 600 mm (A x H) and lenght 1200 mm (L).

For their supply the SR Muffers are definedas follows: SR-P-A x H x L

Design and custom-made construction

For the implementation of every cabin or screening, Vibcon'sengineering department will work out a project divided in threephases: calculation and design, follow-up and final certification.

Input data to be tested will be as follows:

Zone of acoustic sensibility where the machine is placed.Maximum level of sonorous exterior emission.Distance to the recipient.Sonorous power of the equipment.Sonorous spectrum of the equipment.Location established for machine placement.

Documents

Vibroacoustic Control Isolation