Update Alert: Firmware updates are posted to the web on a … · 2017-08-18 · Update Alert: Firmware updates are posted to the web on a regular basis. ... Note: the ishood pin only

Index

Update Alert: Firmware updates are posted to the web on a regular basis. We recommend

that you check for firmware and/or install guide updates prior to installing this product.

Rev.: 20170818

Platform: DBALL2

Firmware TL3: Remote Start Ready Installation(RSR)

© 2017 Directed. All rights reserved.

® Toyota Lexus are registered trademarks and property of .and their respective companies

Vehicle Application Guide ....... ................................................... ............................... ..........................................................

OEM Remote Starter Detection.........................................................................................................................................

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Type 1.............. ..... .................................................................................................................... ..........................................T 2 .......................................................................... ..........................................ype .............. ..... ..........................................SmartStart/ 202 Installation Notes..................................................................................................................................XL

ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................

LED Diagnostics & Troubleshooting...................................................................................................................................Parking Light Error Codes..................................................................................................................................................

Limited One-Year Consumer .............................Warranty............................................................................................. .....

Quick Reference Guide......................................................................................................................................................

02

03

040608

0910101111

1214

15

16

Installation Guide

SmartStart CompatibleSmartStart is equipped with D2D which means it can be connected to an interface module and used in, RemoteStart Ready ( ) mode the use of See the section for moreRSR without a remote starter. Module Programminginformation.

Important!This product is compatible with vehicles equipped with a manual transmission.NOT

Remote Start Ready ( ) is a function that enables the interface module to remote start the vehicleRSRcompletely on its own. Consequently, there is no need for an aftermarket or an remote starter in order toOEMstart the vehicle from a distance.

This guide supports the installation of a in Remote Start Ready ( ) mode.This solution offersDBALL RSRthree (3) configuration options to control your system; 3x Lock Remote Start Activation, Kit orOEM RFSmartStart (all sold separately).

WARNING- No takeover feature is available. The engine will stop when a door is open.- To remote start the engine, all doors must be closed.- Keyless and Smart Key will remain functional during remote start.

Rev.: 20170818

Platform: DBALL2



Vehicle Application GuidePage 2

The following table lists the vehicles and features which are compatible with this product. The number assigned to each yearallows you to determine which installation type should be used for your vehicle.

Important Remote Starter InformationOEM

� I OEMf the vehicle is equipped with an Add-On Lexus/Toyota remote starter:The 3 firmware will detect it and will program into convenience only (no immobilizer bypass). The reason for this is toTLallow aftermarket security to be installed while keeping the factory remote starter active. If you wish to use 3TLfirmware to control the remote start sequence, the factory remote starter must be disconnected before programmingthe 2 as both modules cannot coexist. See locating the Remote Start on page 3.DBALL OEM

� I BCM OEMf the vehicle is equipped with a Enabled Lexus/Toyota remote starter:The 3 firmware will only operate if the vehicle is equipped with an Remote Start System which isTL OEM ENABLEDby activating the Toyota/Lexus Enform Remote System in the using a dealer scan tool. The vehicle does not haveBCMa physical remote start and if not eqquiped with an remote start system, the 3 firmware will notENABLED OEM TLprogram.

Vehicles

2015

2014

2013

2012

2011

2010

2009

2008

2007

DL-A

rm

Facto

ry

Security

DL-D

isarm

Facto

ry

Security

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

riv

er

Prio

rity

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

PK

-Im

mobiliz

er

Bypass-D

ata

No

Key

Req'd

PK

-P

ush

To

Sta

rtIg

nitio

nC

om

patible

RS

-3X

Lock

Sta

rt(S

tartC

ontr

olU

sin

gO

EM

Rem

ote

)

RS

-3X

Lock

Sto

p(S

top

Contr

olU

sin

gO

EM

Rem

ote

)

RS

-A

ccessory

Activation

RS

-Ig

nitio

nA

ctivation

RS

-R

em

ote

Sta

rtR

eady

RS

-S

martS

tart

RS

-S

tart(C

rank)

Activation

RS

-T

ach

/R

PM

Outp

ut

SS

-E

ntr

yM

onitorin

gA

LL

Door

Pin

s

SS

-E

ntr

yM

onitorin

gD

riv

er

Door

Pin

SS

-E

ntr

yM

onitorin

gH

ood

Pin

SS

-E

ntr

yM

onitorin

gT

runk/H

atc

hP

in

SS

-F

acto

ry

Ala

rm

Trig

ger

Monitorin

g

ST

-B

rake

Sta

tus

(fo

otbrake)

ST

-Ig

nitio

nS

tatu

s

Lexus

LS 460 (Smart Key) 2 2 2 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • • • •

LS 600h (Smart Key) 2 2 2 2 2 2 2 2 • • • • • • • • • • • • • • • • • • • • • • •

LX 570 (Smart Key) 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • •

Toyota

Land Cruiser (Smart Key) 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • • • • •

Legend:DL: OE Door Lock & Alarm ControlsPK: Transponder & Immobilizer OverrideRS: Remote Start & Engine ControlsSS: Integrated Security & MonitoringST: Function/Feature Status

Rev.: 20170818

Platform: DBALL2



Locating the remote starterOEM

Page 3

Installation

TypeVehicle OEM Remote Starter & Connectors Location

1 Lexus LX 570 2010-2015 Behind glove box & Passenger kick panel

1 Toyota Land Cruiser 2010-2015 Behind glove box & Passenger kick panel

If the Vehicle is Equipped with an Remote StarterOEM

How to Know if the Vehicle is Equipped with an Remote StarterOEM

I ’f the vehicle is equiped with an , the will detect it and won t complete the programming sequence inOEM DBALLRSorder to prevent to lose programingOEM RS its . To complete the programming you need to disconnect theDBALL OEMRS.

1- An “ ”ENGINE STARTERsticker should be on the remote.

2- Remote start the remote starter:OEMPress the remote control’s lock button twice within 2 seconds,then press and hold the lock button for 3 seconds.

The parking lights flash after 3 seconds. The engine starts andthe parking lights flash repeatedly for 20 seconds.

ENGINESTARTER

x2 &Press & Holdfor 3 seconds

Rev.: 20170818

Platform: DBALL2



HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(+) 12 : 7V Input Brown:

(Starter Switch)(+) Output: 8STSW Yellow:

(+) 12 : 13V Input Red:

(-) Ground: 14Black:

[1] (-) Push-to-Start Output: 2Green/Black:

[1] (-) Push-to-Start:pin 17Black,

(-) Parking lights:, pin 23Violet

23 2226 18

10 7

25

13141617

19

8

20

9111215

24

123456

23

17

21

See for help on locating key components in vehicle .page 5 the and wiring reference chart

(-) Parking Lights Output: 4Red/Black:

Page 4

10

2DBALL

RF

Prog. button

LED

4

14

12

2

Installation Type 1

Unless specified otherwise, all connectors are displayed from the wire side.

Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL

6: (-) HoodWhite/Black:

Hood Pin

Note: the ishood pin onlyrequired on vehicle notequipped with a factory hood pin

Remote Start SafetyOverride Switch

810

HS CAN High:Gray, pin 16

HS CAN Low:Red, pin 15

14

5

1116 15

23

1615

E3(White conn. at Main Body ECU)

6

12

7

13

8

14


E4 2AE1 E3

MainBody

ECU

12

356

7910

4

8

14

57810

11131416

69

1215

23

16 15

1

23 2226 18

10 7

25

13141617

19

8

22 01

9111215

24

123456

17

12

356

7910

4

(+) :STSWRed, pin 4

(+) 12V:Black, pin 1


2A(White conn. at Main Body ECU)

1

You can connect to either a 202XLRFTD a SmartStart module.OR

Refer to the SmartStart/ 202XLInstallation Notes for more information.

Autolight:Green, pin 21

Autolights Interr. (veh. side) 10Orange/Red:

Autolights Interr. (conn. side) 11Yellow/Red:

CUT

[1] PTS connection required only if Pit-Stop / Idle mode is desired.

Not required in D2D mode.

Rev.: 20170818

Platform: DBALL2



Page 5

Locating omponents in the ehicleC V

Main Body ECU

WARNING- No take over feature is available. The engine will stop when a door is open.- To remote start the engine, all doors must be closed.

Type 1 - Vehicle Wiring Reference Chart

Important Information

Pit-Stop/Idle Mode

The Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle.Refer to the owner's guide of your remote starter for more details.

Function Color Pin Polarity Location Color Pins

HS CAN High Gray 16 Data E3 connector at Main Body ECU. White 16

HS CAN Low Red 15 Data E3 connector at Main Body ECU. White 16

Autolights Shutoff Green 21 Cut E1 connector at Main Body ECU. White 26

Parking Lights Violet 23 (-) E1 connector at Main Body ECU. White 26

Push-To-Start Black 17 (-) E1 connector at Main Body ECU. White 26

Starter Switch Red 4 (+) E4 connector at Main Body ECU. White 10

12V Black 1 (+) 2A connector at Main Body ECU. White 1

HS CAN High Gray 16 Data E3 connector at Main Body ECU. White 16

HS CAN Low Red 15 Data E3 connector at Main Body ECU. White 16

Autolights Shutoff Green 21 Cut E1 connector at Main Body ECU. White 26

Parking Lights Violet 23 (-) E1 connector at Headlight Switch. White 26

Push-To-Start Black 17 (-) E1 connector at Main Body ECU. White 26

Starter Switch Red 4 (+) E4 connector at Main Body ECU. White 10

12V Black 1 (+) 2A connector at Main Body ECU. White 1

Wire Information Connector Information

Lexus LX 570 2008-2015

Toyota Land Cruiser 2008-2015

Rev.: 20170818

Platform: DBALL2



HS CAN High: 3Tan/Black:

HS CAN Low: 4Tan:

(+) Output: 8STSW (Starter Switch) Yellow:

(+) 12 : 13V Input Red:

(-) Ground: 14Black:

[1] (-) Push-to-Start Output: 2Green/Black:

(-) Parking Lights Output: 4Red/Black:

(+) 12 : 7V Input Brown:

12

356

7910

4

(+) :STSWBlack, pin 4

(+) 12V:Yellow, pin 1

A68(White conn. at

Main Body ECU)

[1] (-) Push-to-Start:White, pin 17

L13(White conn. at Main Body ECU)

23 2226 18

10 7

25

13141617

19

8

20

9111215

24

123456

23

17

21

12

356

7910

4

8

14

57810

11131416

69

1215

23

16 15

MainBody

ECU

1

23 2226 18

10 7

25

13141617

19

8

22 01

9111215

24

123456

17

A68 DGL13 L11

6: (-) HoodWhite/Black:

Hood Pin

Note: the ishood pin onlyrequired on vehicle notequipped with a factory hood pin

You can connect to either a 202XLRFTD a SmartStart module.OR

Refer to the SmartStart/ 202XLInstallation Notes for more information.

Page 6

Installation Type 2

U , all connectors are displayed from the wire side.nless specified otherwise

10

2DBALL

RF

Prog. button

LED

4

14

12

2

DG conn.(White conn. at Main Body ECU)

1

12345678910

1112131415161718

(-) Parking ights:LBlue, pin 18

20

Z6( at Headlight Switch)White conn.

See for help on locating key components in vehicle .page 7 the and wiring reference chart

Important!The devices, but supplied with the .Hood Pin and Remote Start Safety Override Switch are mandatory safety are NOT DBALL

Remote Start SafetyOverride Switch

810

HS CAN High:Gray, pin 16

HS CAN Low:Red, pin 15

14

5

1116 15

23

1615

L11(White conn. at Main Body ECU)

6

12

7

13

8

14

Autolight:,Orange pin 19

CUT

Autolights Interr. (veh. side) 10: Orange/Red:

Autolights Interr. (conn. side) 11: Yellow/Red:

19

[1] PTS connection required only if Pit-Stop / Idle mode is desired.

Not required in D2D mode.

Rev.: 20170818

Platform: DBALL2



Page 7

Type 2 - Vehicle Wiring Reference Chart

Main Body ECU

Locating Components in the Vehicle

WARNING- No take over feature is available. The engine will stop when a door is open.- To remote start the engine, all doors must be closed.

Headlight switchconnector (z6)

Function Color Pin Polarity Location Color Pins

HS CAN High Black 16 Data L11 connector at Main Body ECU. White 16

HS CAN Low White 15 Data L11 connector at Main Body ECU. White 16

Autolights Shutoff Orange 19 Cut Z6 connector at Headlight Switch. White 20

Parking Lights Blue 18 (-) Z6 connector at Headlight Switch. White 20

Push-To-Start White 17 (-) L13 connector at Main Body ECU. White 26

Starter Switch Black 4 (+) A68 connector at Main Body ECU. White 10

12V Yellow 1 (+) DG connector at Main Body ECU. White 1

HS CAN High Black 16 Data L11 connector at Main Body ECU. White 16

HS CAN Low White 15 Data L11 connector at Main Body ECU. White 16

Autolights Shutoff Orange 19 Cut Z6 connector at Headlight Switch. White 20

Parking Lights Blue 18 (-) Z6 connector at Headlight Switch. White 20

Push-To-Start White 17 (-) L13 connector at Main Body ECU. White 26

Starter Switch Black 4 (+) A68 connector at Main Body ECU. White 10

12V Yellow 1 (+) DG connector at Main Body ECU. White 1

Wire Information Connector Information

Lexus LS 460 2007-2015

Lexus LS600h 2008-2015

Pit-Stop/Idle Mode

The Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle.Refer to the owner's guide of your remote starter for more details.

Important Information

Rev.: 20170818

Platform: DBALL2



Page 8

The 202 and antenna are not included and be purchased separately.optional XL MUST

Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE

4

4

XL202

An

ten

na

XOVER

SmartStart is and not included. It be purchased separately.optional MUST

SmartStart is and not included. It be purchased separately.optional MUST

Th solution offers three (3) configuration options to control your system; 3xe Remote Start Ready ( )DBALL RSR OEMLock Remote Start Activation, Kit or SmartStart (all sold separately).RF This section provides specific installationinformation for SmartStart and 202.XL

Configuration Wires (Gray & White)Connect Gray wire to (-) Ground

5 pins

D2D (4 pins, white)

4 pins

2 pins,not usedCABLE

CABLE

The modules must be connected in a specific order. Refer to the section for more information.Module Programming

1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package.XOVER XL NOT DBALL2. The modules must be connected in a specific order. Refer to the section for more information.Module Programming

The modules must be connected in a specific order. Refer to the section for more information.Module Programming

SmartStart/ 202 Installation NotesXL

SmartStart Revision B

RF Kit

RF PKE& CombinationKit

Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE

RF PKE BT, & SmartStart CombinationKit

SmartStart Revision A

DBALL/2DBALL

DBALL/2DBALL

DBALL/2DBALL

LED

Prog.Button

D2D (4 pins, white)

4 pins

2 pins,not used

OR

SmartStart

Configuration Wires (White & Brown or Blue)Cut Brown or Blue Loop

LED

THIS SIDE UP

LED

Rev.: 20170818

Platform: DBALL2



Page 9

Module Programming

3

Refer to the Diagnostics section on page 12 for more information and for troubleshooting purposes.LED

110-pinD2D

1st

12-pin14-pin

2nd

3rd

&Solid

the 10-pin 2-pin harnesses toConnect , 1 and 14-pinDBALL, then w .ait until the turns solid redLED ON

2

You have successfully completed the module programming sequence.

ENGINESTARTSTOP

PUSH 1XThe module is now programmed, press the button once more to turn the ignition .PTS OFF

ENGINESTARTSTOP

PUSH 2XPress the ush-to- tart button twice to turn the ignitionP S ( )PTSON LED ON. The green turns for 3 seconds and shuts .OFF & &

Off

Solid Greenx3 Secs

Important

10-pinD2D

XL202

10-pinD2DSmartStart

OR

The module be disconnected from any power source before SmartStart canDBALL mustbe connected to it. Failing to do so could damage .DBALL

a. To ensure that the D2D communication between SmartStart and works properly, theDBALLGray wire must be connected to a ground source ( SmartStart), and the Brown or BlueRev Bloop must be cut ( SmartStart).Rev A

b. Do connect the 2-pin harness (on SmartStart). Power and ground will be provided byNOTthe D2D connector.DBALL

Connect SmartStart to using the D2D port.DBALL

SmartStart Installation

Connect 202 to using the D2D port.XL DBALL

XL202 Installation

Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.

Note: Before connecting either the 202 or SmartStart module to , it is important to ensure that the proper feature andXL DBALLfunction programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latestVIP 5version of the application.

Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP

When the flashing operation is successful, you can proceed with the programming instructions below.

Flashing a module using your computer:

1. Connect the interface module to your computer using theXKLoader2.

2. Go to www.directechs.com using Internet Explorer, andselect the button.Config for RSR

3. Follow the instructions to select your vehicle, installationtype, and configure your options.

4. Once you have configured the firmware options, click on theFLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your oader3.XKL

2. Launch the Directechs Mobile app on your smartphone ortablet.

3. Select and follow the on screenFLASH YOUR MODULEinstructions.

Rev.: 20170818

Platform: DBALL2



Module ResetPage 10

1If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List

2

Solid

&Release

3 Release the programming button. The turns solid red.LED ON

Hard Reset

2 & &

1

Wait 3 seconds until the orange then release theLED turns solidONp The turns solid red.rogramming button. LED ON

If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.

10-pinD2D

1st

12-pin14-pin

2nd

4th

3rd

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.

Solid Release Solid

Solid Flashes

&Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.

Rev.: 20170818

Platform: DBALL2



Page 11

Feature Option List&

* Default option

Feat. Operation Flashes / Option Description

1. Disabled* Module is connected to a remote starter using a standard installation.

2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).

3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).

1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.

2. All Unlocks all doors on first press.

1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the

beginning or end of the sequence; it must be controlled by the Remote Starter.

2. NormalSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning

of the sequence, and relock after start and shutdown.

3. Smart OEM

Alarm Control*

Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote

start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock

operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible,

Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the

vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm

Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter,

for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user.

3Smart OEM

Alarm Control

Unlock Driver

Priority2

1RF Output

Type

To enter feature programming routine� Turn t , thenhe ignition .ON OFF� Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )

Programming button.� The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red

the current option of feature 1 .(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willrepeat until .a new command is entered

Changing feature options� Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the

DBALL RSR OEMin using 3x Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock tochange the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 10-pin harness to ground willchange the option for the selected feature.

� The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDredthe number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered

Accessing another feature� Press and release the programming button a number of times to advance from the current feature to the next desired feature.� The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED

indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered

When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED

Once a feature is programmed� Other features can be programmed.� The feature programming can be exited.

Exiting feature programming� No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON

sequence.OR

� Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.

Feature ProgrammingProgramming

Button

It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options such as ; however, manual configuration of theRSRfeatures is possible using the information on this page.

Rev.: 20170818

Platform: DBALL2



Page 21

LED Diagnostics & Troubleshooting

LED Description Troubleshooting

Module has no power.

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Waiting to begin the programming sequence.Ensure the correct programming procedure is being

followed.

Initialization failed.Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

Transponder functions were skipped.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

All required CAN networks has been detected. Normal operation.

1 of 2 CAN networks has been detected. Normal operation

Key2GO initiated.Please follow the steps indicated in “Module

programming” to complete the Key2GO programming.

Module was successfully programmed with all functions. Normal operation

Module was successfully programmed without

transponder functions.Normal operation.

CAN2 not detected.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

J1850 not detected.Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

CAN1 not detected.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Bypass data not detected.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

Bypass processing error.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

ISO 1 not detected.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

ISO 2 not detected.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

MUX not detected.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Module Programming

Module Programming - Error Codes

Solid red

Flashes redx 1

Flashes redx 1

Flashes redx 2

Flashes redx 3

Flashes redx 4

Flashes redx 5

Flashes redx 6

Flashes redx 7

Solid greenx 3 secs

Flashesgreen

Solid orange

Flashes red& green

Off

Flashesorange

Flashesorangeslowly

Solid orangex 3 secs

Rev.: 20170818

Platform: DBALL2



Page 13

LED Description Troubleshooting

OBDII feature is not supported.The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

Ground When Running (Status) command received. The module has initialized the remote start sequence.

Ignition ON command received.The module has received the Ignition ON command and

is processing the remote start sequence.

Start ON command received.The module has received the Start ON command and is

processing the remote start sequence.

PTS shutdown error.The PTS output from the module was not activated due

to safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to

“Installation (wiring diagrams & vehicle wiring reference

charts)” to check the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.



Takeover successful. Normal operation.

Runsafe was not disabled.No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

Brake was not detected.The brakes were not detected, which prevents the

system from shutting down the vehicle.

Smart key was not detected.The smart key was not detected, which prevents the

system from shutting down the vehicle.

Speed was detected.The vehicle was detected as moving, which prevents the

system from shutting it down.

3x OEM Lock Remote Start Activation was attempted

when RFTD feature is disabled.

Activated from Web automatically when using RSR flash

tool or can be done manually. Refer to feature

programing section for more information.

Feature error.An RSR feature file mismatch was detected. Please

contact Technical Support.

RSR codes

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,red thenorange) x 10

Flashes red& orange

Flashes redx 21

Flashes redx 2

Flashes redx 4

Flashes redx 7

Flashes redx 9

Flashes redx 10

Flashes redx 1

Flashes redx 3

Flashesgreen

Flashesgreenquickly

Flashesgreen x 1

Flashesorange x 1

Flashesorange x 2

Flashesorange x 3

Flashesorange x 5

Flashesorange x 4

Flashesorange x 6

Rev.: 20170818

Platform: DBALL2



Flashes Diagnostic

1 Runtime expired.

2 Over-rev shutdown.

3 Low/No RPM.

4 Transmitter shutdown.

5 Brake shutdown.

6 Hood shutdown/Remote start safety override switch is ON*.

7 Remote start safety override switch is ON*.

The parking lights on your vehicle will flash a specific number of times 3 seconds following an unscheduled shutdown orfailure to start. Each flashing pattern is described below.

* If the vehicle hood status is supported through data, safety override switch input will report 7 flashes.

Parking Light Error CodesPage 14

Rev.: 20170818

Platform: DBALL2



Page 15

Limited Consumer WarrantyOne Year

For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.

Quick Reference GuideDBALL2 TL3- Remote Start Ready (RSR) Installation

1

2

3

Stop the vehicle in a safe parking spotand put the gear in Park (P).

Pressremote start

*button

* Your aftermarket remote may differ from the model shown in the illustrations.

Stop & put vehicle in Park (P)

P&

HO

LD

E vehicle withxitSmart Key

Pit Stop Mode

The Mode feature is practical when you need to stop and run an errand,Pit Stopbut wish to keep the engine running.

Note: We recommend that you always lock the doorsof your vehicle when leaving it unattended.

It is now safe to leave the exitengine running and thevehicle with the in hand.factory remote

Press the button to remote start the vehicle.*

The parking lights will flash once to indicatethe vehicle is now in Pit Stop Mode.

Parking Light Error CodesThe parking lights on your vehicle will flash a specific number of times 3 secondsfollowing an unscheduled shutdown . Each flashing pattern isor failure to startdescribed below.

Flashes Diagnostic

1 Runtime expired.

2 Over-rev shutdown.

3 Low/No RPM.

4 Transmitter shutdown.

5 Brake shutdown.

6 Hood shutdown/Remote start safety override switch is ON*.

7 Remote start safety override switch is ON*.


Remote Start Ready ( )RSR

Remote Start Ready ( ) is a function that enables the interfaceRSRmodule to remote start the vehicle completely on its own.Consequently, there is no need for an aftermarket or an remoteOEMstarter in order to start the vehicle from a distance.

3x Lock Remote Start ActivationOEM

This solution includes the option to remote start your vehicle by pressing the Lockbutton 3 times consecutively. If your vehicle allows the remote to remainOEMactive while the engine is running, you may shut down your remote starter bypressing the Lock button 3 times once more.

Note: The range offered by remotes is limited and typically requires you to beOEMwithin eyesight of the vehicle to control it.

* If the vehicle hood status is supported through data, it will also report a 7 flashsafety override code.

Vehicle Takeover

Note: There is no vehicle takeover in this firmware. The vehicle willshut down as soon as a door is opened.


SmartStart Compatible

This system is compatible with Directed SmartStart 3.0. Fora complete list of supported features, please visitwww.mysmartstart.com.

What is SmartStart?

Now you can remote start, lock and unlock your car just by pushing a button onyour smartphone; using the SmartStart App from Directed, the leader in vehiclesecurity and remote start. The simple graphical interface gives you control over thefollowing features of your installed remote start or security with remote start system:

� Lock/Arm� Unlock/Disarm� Remote Car Starter� Trunk Release� Panic� Aux Channels

You can also control multiple vehicles – great for families – and assign more thanone user to control a vehicle. It's easy with SmartStart!

But, this is only the beginning! SmartStart is loaded with additional featuresincluding tracking, SmartSchedule, vehicle status, roadside assistance, homeGPScontrol, parked car finder and more.

3.0 enables a "Cloud-Connected Car" like never before, providing an entirely newlevel of 2-way interaction with your vehicle. Connectivity is managed through theDirected Cloud Services ( ) network linking car, app, end user, and the Internet.DCS

For more information, visit www.mysmartstart.com.

Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x3 +

x1 +

* This output is configurable. see your authorized installation center for moreinformation.

Note that the information below is for Viper, Clifford and Python models. Icons andcommands may differ depending on the remote brand and model purchased. Referto your authorized installation center for more information.


Notes

Documents

Update Alert: Firmware updates are posted to the web on a … · 2017-08-18 · Update Alert: Firmware updates are posted to the web on a regular basis. ... Note: the ishood pin only