1. Command: unitsklik “units to scale inserted” kemudian pilih “milimeters” Klik “precision” kmeudian pilih “0,000”.

2. Command: os masukan perintah “OS” klik (beri tanda centang) pada “endpoint”,Midpoint”, “center”, “node”, “quadrant”,”intersectiom”, “extentiom”, “intersection”, “perpendicular”, “tangent”, “nearest”, “appparent intersection”, dan “ parllrel”

3. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0Specify radius of circle or [Diameter]: 4

4. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0Specify radius of circle or [Diameter] <4.0000>: 5

5. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0Specify radius of circle or [Diameter] <5.0000>: 6

6. Command: lLINE Specify first point:Specify next point or [Undo]: @2<0

7. Command: mMOVESelect objects: 1 foundSelect objects:

Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>: *Cancel*

8. Command: mMOVESelect objects: 1 found

Select objects:

Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>:

9. Command: lLINE Specify first point:Specify next point or [Undo]:

10. Command: lLINE Specify first point:Specify next point or [Undo]:

11. Command: lLINE Specify first point: 0,0

Specify next point or [Undo]:

12. Command: _propertiesCommand: _.erase 1 found

13. Command:14. Command: _.erase 1 found

15. Command:16. Command: _.erase 1 found

17. Command:18. Command: _.erase 1 found

19. Command:20. Command: _.erase 1 found

21. Command: tr

TRIMCurrent settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

22. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

23. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

24. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

25. Command: arARRAYSelect objects: 1 foundSelect objects: 1 found, 2 totalSelect objects:Specify center point of array: 0,0Pick or press Esc to return to dialog or <Right-click to accept array>:

26. Command: trTRIMCurrent settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

27. Command: Specify opposite corner:Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0

28. Specify radius of circle or [Diameter] <6.0000>: 8

29. Command: polPOLYGON Enter number of sides <4>: 6

30. Specify center of polygon or [Edge]: eSpecify first endpoint of edge: 15Specify second endpoint of edge: 15

31. Command: lLINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]: *Cancel*

32. Command: mMOVESelect objects: 1 found

33. Select objects:

34. Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>:Command:Command: _.erase 1 found

35. Command:ERASESelect objects: *Cancel*

36. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <8.0000>: 5

37. Command: arARRAYSelect objects: 1 found

38. Select objects:

39. Command: trTRIM

Current settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

40. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

41. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

42. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

43. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

44. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

45. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

46. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

47. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

48. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

49. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

50. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

51. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

52. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

53. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

54. Command: mMOVESelect objects: Specify opposite corner: 46 found

55. Select objects:

56. Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>:

57. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0

58. Specify radius of circle or [Diameter] <5.0000>: 8

59. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0

60. Specify radius of circle or [Diameter] <8.0000>: 10

61. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0

62. Specify radius of circle or [Diameter] <10.0000>: 15

63. Command: lLINE Specify first point:Specify next point or [Undo]: @2<0

64. Command: lLINE Specify first point:Specify next point or [Undo]: @3<0

65. Command: lLINE Specify first point:Specify next point or [Undo]: @3<0

66. Specify next point or [Undo]: *Cancel*

67. Command: mMOVESelect objects: 1 found

68. Select objects:

69. Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>:

70. Command: l

71. LINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]:Specify next point or [Close/Undo]:Specify next point or [Close/Undo]: *Cancel*

72. Command: lLINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]:Specify next point or [Close/Undo]:Specify next point or [Close/Undo]: *Cancel*

73. Command:Command: Specify opposite corner:Command: _.erase 1 found

Command:74. Command: _.erase 1 found

75. Command:Command: _.erase 1 found

76. Command:Command: _.erase 1 found

77. Command:Command: _.erase 1 found

78. Command: trTRIMCurrent settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

79. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

80. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

81. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

82. Command: trTRIMCurrent settings: Projection=UCS, Edge=None

Select cutting edges ...Select objects or <select all>:

83. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

84. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

85. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

86. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

87. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

88. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

89. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

90. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

91. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

92. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

93. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

94. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

95. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

96. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

97. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

98. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

99. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

100. Command:Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0

101. Specify radius of circle or [Diameter] <15.0000>: 30

102. Command: polPOLYGON Enter number of sides <6>: 16

Specify center of polygon or [Edge]: eSpecify first endpoint of edge: 15Specify second endpoint of edge: 15

103. Command: lLINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]: *Cancel*

104. Command: mMOVESelect objects: 1 found

105. Select objects:

106. Specify base point or [Displacement] <Displacement>: Specify second point or <use first point as displacement>:Command:Command: _.erase 1 found

107. Command: c108. CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:109. Specify radius of circle or [Diameter] <30.0000>: 5110.111. Command: tr112. TRIM113. Current settings: Projection=UCS, Edge=None114. Select cutting edges ...115. Select objects or <select all>:

116.117. Select object to trim or shift-select to extend or118. [Fence/Crossing/Project/Edge/eRase/Undo]:119.120. Select object to trim or shift-select to extend or121. [Fence/Crossing/Project/Edge/eRase/Undo]: *Cancel*122.123. Command: ar124. ARRAY125. Select objects: 1 found126.127. Select objects:128.129. Command: tr

TRIMCurrent settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

130. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

131. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

132. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

133. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

134. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

135. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

136. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

137. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

138. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

139. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

140. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

141. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

142. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

143. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

144. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

145. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

146. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

147. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

148. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

149. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:

150. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

151. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

152. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

153. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

154. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

155. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

156. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

157. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

158. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

159. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

160. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

161. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

162. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: *Cancel*Nyritakke iki ngubajh jenis garisnggon ruji

163. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <5.0000>: 6

164. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <6.0000>: *Cancel*

165. Command: Specify opposite corner:Command: _.erase 1 found

166. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <6.0000>: 6

167. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:

168. Specify radius of circle or [Diameter] <6.0000>: 4.75

169. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <4.7500>: 3

170. Command:Command: coCOPYSelect objects: Specify opposite corner: 3 found

171. Select objects:

172. Current settings: Copy mode = Multiple173. Specify base point or [Displacement/mOde] <Displacement>: Specify second point 174. or <use first point as displacement>: @15<0

175. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: ttr

176. Specify point on object for first tangent of circle:Specify point on object for second tangent of circle:Specify radius of circle <3.0000>: 9

177. Command: trTRIMCurrent settings: Projection=UCS, Edge=NoneSelect cutting edges ...Select objects or <select all>:

178. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]: Specify opposite corner:No objects crossed by crossing window.Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

179. Select object to trim or shift-select to extend or[Fence/Crossing/Project/Edge/eRase/Undo]:

180. Command: miMIRRORSelect objects: 1 found

181. Select objects:

Specify first point of mirror line: Specify second point of mirror line:Erase source objects? [Yes/No] <N>:

182. Command:Command: roROTATECurrent positive angle in UCS: ANGDIR=counterclockwise ANGBASE=0.000

183. Select objects: Specify opposite corner: 113 found

184. Select objects:

185. Specify base point:Specify rotation angle or [Copy/Reference] <45.000>: 180

186. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <9.0000>: 120

187. Command: cCIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:Specify radius of circle or [Diameter] <120.0000>: 120

188. Command: lLINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]: *Cancel*

189. Command: lLINE Specify first point:Specify next point or [Undo]:Specify next point or [Undo]: *Cancel*

190. Command: alALIGNSelect objects: Specify opposite corner: 71 found

191. Select objects:

192. Specify first source point:Specify first destination point:Specify second source point:Specify second destination point:Specify third source point or <continue>:

193. Scale objects based on alignment points? [Yes/No] <N>: Y

194. Command:Command: _.erase 1 found

195. Command:Command: _.erase 1 found

196. Command:Command: _.erase 1 found

197. Command:Command: _.erase 1 found

198. Command: coCOPYSelect objects: Specify opposite corner: 8 found

199. Select objects:

200. Current settings: Copy mode = MultipleSpecify base point or [Displacement/mOde] <Displacement>: Specify second point or <use first point as displacement>:

201. Specify second point or [Exit/Undo] <Exit>:202. Specify second point or [Exit/Undo] <Exit>:203. Specify second point or [Exit/Undo] <Exit>:204. Specify second point or [Exit/Undo] <Exit>:205. Specify second point or [Exit/Undo] <Exit>:206. Specify second point or [Exit/Undo] <Exit>:207. Specify second point or [Exit/Undo] <Exit>:208. Specify second point or [Exit/Undo] <Exit>:209. Specify second point or [Exit/Undo] <Exit>:210. Specify second point or [Exit/Undo] <Exit>:211. Specify second point or [Exit/Undo] <Exit>:212. Specify second point or [Exit/Undo] <Exit>:213. Specify second point or [Exit/Undo] <Exit>:214. Specify second point or [Exit/Undo] <Exit>:215. Specify second point or [Exit/Undo] <Exit>:216. Specify second point or [Exit/Undo] <Exit>:

217. Command: Specify opposite corner:Command: _.erase 8 found

218. Command: '_ZOOMSpecify corner of window, enter a scale factor (nX or nXP), or[All/Center/Dynamic/Extents/Previous/Scale/Window/Object] <real time>:

219. Command: Specify opposite corner:220. Command: al221. ALIGN222. Specify first source point:223. Specify first destination point:224. Specify second source point:225. Specify second destination point:226. Specify third source point or <continue>:

227. Scale objects based on alignment points? [Yes/No] <N>:

228. Command:229. ALIGN230. Select objects: Specify opposite corner: 8 found

231. Select objects:

232. Specify first source point:233. Specify first destination point:234. Specify second source point:235. Specify second destination point:236. Specify third source point or <continue>:237. Command: co238. COPY239. Select objects: Specify opposite corner: 8 found

240. Select objects:

241. Current settings: Copy mode = Multiple242. Specify base point or [Displacement/mOde] <Displacement>: Specify second point 243. or <use first point as displacement>:244. Specify second point or [Exit/Undo] <Exit>:245. Specify second point or [Exit/Undo] <Exit>:246. Specify second point or [Exit/Undo] <Exit>:247. Specify second point or [Exit/Undo] <Exit>:248. Specify second point or [Exit/Undo] <Exit>:249. Specify second point or [Exit/Undo] <Exit>:250. Specify second point or [Exit/Undo] <Exit>:251. Specify second point or [Exit/Undo] <Exit>:252. Specify second point or [Exit/Undo] <Exit>: *Cancel*

253. Command: al254. ALIGN255. Select objects: Specify opposite corner: 8 found

256. Select objects:

257. Specify first source point:258. Specify first destination point:259. Specify second source point:260.261. Command:262. ALIGN263. Select objects: Specify opposite corner: 8 found

264. Select objects:

265. Specify first source point:266. Specify first destination point:267. Specify second source point:

268. Command: al269. ALIGN270. Select objects: Specify opposite corner: 8 found271.272. Select objects:

273. Specify first source point:274. Specify first destination point:275. Specify second source point:

276. Command: al277. ALIGN278. Select objects: Specify opposite corner: 16 found

279. Select objects:

280. Specify first source point:281. Specify first destination point:282. Specify second source point:

283. Command: al284. ALIGN285. Select objects: Specify opposite corner: 8 found

286. Select objects:

287. Specify first source point:288. Specify first destination point: *Cancel*

289. Command: al290. ALIGN291. Select objects: Specify opposite corner: 8 found

292. Select objects:

293. Specify first source point:294. Specify first destination point:295. Specify second source point:

296. Command: al297. ALIGN298. Select objects: Specify opposite corner: 8 found

299. Select objects:

300. Specify first source point:301. Specify first destination point:302. Specify second source point:

303. Command: al304. ALIGN305. Select objects: Specify opposite corner: 8 found

306. Select objects:

307. Specify first source point:308. Specify first destination point:309. Specify second source point:310. Command: al311. ALIGN312. Select objects: Specify opposite corner: 72 found

313. Select objects:

314. Specify first source point:315. Specify first destination point:316. Specify second source point:317. Specify second destination point:318. Command: ro319. ROTATE320. Current positive angle in UCS: ANGDIR=counterclockwise ANGBASE=0.000

321. Select objects: Specify opposite corner: 349 found

322. Select objects:

323. Specify base point:324. Specify rotation angle or [Copy/Reference] <18.799>: 30