TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH … Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TLE207x, TLE207xA ... Q15 Q16 Q19 Q20

TLE207x, TLE207xAEXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

�

SLOS181C − FEBRUARY 1997 − REVISED DECEMBER 2009

1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

� Direct Upgrades to TL05x, TL07x, andTL08x BiFET Operational Amplifiers

� Greater Than 2× Bandwidth (10 MHz) and3× Slew Rate (45 V/μs) Than TL07x

� Ensured Maximum Noise Floor17 nV/√Hz

� On-Chip Offset Voltage Trimming forImproved DC Performance

� Wider Supply Rails Increase DynamicSignal Range to ±19 V

description

The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slewrate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur processyields a typical noise floor of 11.6 nV/√Hz, 17-nV/√Hz ensured maximum, offering immediate improvement innoise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasingthe dynamic signal range for BiFET circuits to ±19 V. On-chip zener trimming of offset voltage yields precisiongrades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lowerperformance BiFET operational amplifiers for ease in improving performance in existing designs.

BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, withoutsacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing withhigh-impedance sensors or very low-level ac signals. They also feature inherently better ac response thanbipolar or CMOS devices having comparable power consumption.

The TLE207x family of BiFET amplifiers are Texas Instruments highest performance BiFETs, with tighter inputoffset voltage and ensured maximum noise specifications. Designers requiring less stringent specifications butseeking the improved ac characteristics of the TLE207x should consider the TLE208x operational amplifierfamily.

Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken toobserve common-mode input voltage limits and output swing when operating from a single supply. DC biasingof the input signal is required and loads should be terminated to a virtual ground node at mid-supply. TexasInstruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from singlesupplies.

The TLE207x are fully specified at ±15 V and ±5 V. For operation in low-voltage and/or single-supply systems,Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended. Whenmoving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidthrequirements and output loading.

Copyright © 1997 − 2004, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.

�

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

TLE207x, TLE207xAEXCALIBUR LOW-NOISE HIGH-SPEEDJFET-INPUT OPERATIONAL AMPLIFIERS

�


2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLE2071 AVAILABLE OPTIONS

PACKAGED DEVICES

TAVIOmaxAT 25°C

SMALLOUTLINE†

(D)

CHIP CARRIER(FK)

CERAMIC DIP(JG)

PLASTIC DIP(P)

CERAMICFLAT PACK

(U)

0°C to 70°C2 mV TLE2071ACD TLE2071ACP

0°C to 70°C2 mV4 mV

TLE2071ACDTLE2071CD — —

TLE2071ACPTLE2071CP —

40°C to 85°C2 mV TLE2071AID TLE2071AIP

−40°C to 85°C2 mV4 mV

TLE2071AIDTLE2071ID — —

TLE2071AIPTLE2071IP —

55°C to 125°C 2 mV — TLE2071AMFK TLE2071AMJG — TLE2071AMU−55°C to 125°C 2 mV

4 mV —TLE2071AMFKTLE2071MFK

TLE2071AMJGTLE2071MJG —

TLE2071AMUTLE2071MU

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2071ACDR).


PACKAGED DEVICES

TAVIOmaxAT 25°C

SMALLOUTLINE†

(D)

CHIPCARRIER

(FK)

CERAMICDIP(JG)

PLASTICDIP(P)

CERAMICFLAT PACK

(U)

0°C to 70°C3.5 mV TLE2072ACD TLE2072ACP

0°C to 70°C3.5 mV

6 mVTLE2072ACDTLE2072CD — —

TLE2072ACPTLE2072CP —

40°C to 85°C3.5 mV TLE2072AID TLE2072AIP

−40°C to 85°C3.5 mV

6 mVTLE2072AIDTLE2072ID — —

TLE2072AIPTLE2072IP —

55°C to 125°C 3.5 mV TLE2072AMFK TLE2072AMJG TLE2072AMU−55°C to 125°C 3.5 mV

6 mV—

TLE2072AMFKTLE2072MFK

TLE2072AMJGTLE2072MJG

—TLE2072AMUTLE2072MU

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2072ACDR).


PACKAGED DEVICES

TAVIOmaxAT 25°C

SMALLOUTLINE†

(DW)

CHIPCARRIER

(FK)

CERAMICDIP(J)

PLASTICDIP(N)

CERAMICFLAT PACK

(W)

0°C to 70°C3 mV TLE2074ACDW TLE2074ACN

0°C to 70°C3 mV5 mV

TLE2074ACDWTLE2074CDW — —

TLE2074ACNTLE2074CN —

40°C to 85°C3 mV TLE2074AIDW TLE2074AIN

−40°C to 85°C3 mV5 mV

TLE2074AIDWTLE2074IDW — —

TLE2074AINTLE2074IN —

55°C to 125°C 3 mV TLE2074AMFK TLE2074AMJ TLE2074AMW−55°C to 125°C 3 mV

5 mV—

TLE2074AMFKTLE2074MFK

TLE2074AMJTLE2074MJ

—TLE2074AMWTLE2074MW

† The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2074ACDWR).

symbol

+

−OUT

IN+

IN−



�



1

2

3

4

8

7

6

5

OFFSET N1IN −IN +

VCC −

NCVCC +OUTOFFSET N2

3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

NCVCC +

NCOUTNC

NCIN −NC

IN +NC

NC

OF

FS

ET

N1

NC

NC

NC

NC

VN

CO

FF

SE

T N

2N

C

CC

−

NC − No internal connection

TLE2071 AND TLE2071AD, JG, OR P PACKAGE

(TOP VIEW)

TLE2071M AND TLE2071AMFK PACKAGE(TOP VIEW)

1

2

3

4

8

7

6

5

1OUT1IN−

1IN +VCC −

VCC +2OUT2IN−2IN+

3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

NC2OUTNC2IN−NC

NC1IN−

NC1IN+

NC

NC

1OU

TN

C

NC

NC

NC

VN

C2I

N+

CC

−

VC

C +

TLE2072 AND TLE2072AD, JG, OR P PACKAGE

(TOP VIEW)


3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

4IN+NCVCC −

NC3IN+

1IN+NC

VCC +

NC2IN+

1IN

−1O

UT

NC

3IN

−4I

N −

2IN

−

NC

3OU

T

2OU

T

4OU

T

1

2

3

4

5

6

7

8

16

15

14

13

12

11

10

9

1OUT1IN−1IN+VCC +

2IN+2IN−

2OUTNC

4OUT4IN−4IN+VCC −

3IN+3IN−3OUTNC

1

2

3

4

5

6

7

14

13

12

11

10

9

8

1OUT1IN−1IN+VCC +

2IN+2IN−

2OUT

4OUT4IN−4IN+VCC −

3IN+3IN−3OUT

TLE2074 AND TLE2074ADW PACKAGE

(TOP VIEW)

TLE2074 AND TLE2074AJ, N, OR W PACKAGE

(TOP VIEW)


1

2

3

4

5

10

9

8

7

6

NCOFFSET N1

IN −IN +

VCC−

NCNCVCC+

OUTOFFSET N2

TLE2071 AND TLE2071AU PACKAGE(TOP VIEW)

1

2

3

4

5

10

9

8

7

6

NC1OUT

1IN−1IN+VCC−

NCVCC+

2OUT2IN−2IN+

TLE2072 AND TLE2072AU PACKAGE(TOP VIEW)

TL

E207x, T

LE

207xAE

XC

AL

IBU

R L

OW

-NO

ISE

HIG

H-S

PE

ED

JFE

T-INP

UT

OP

ER

AT

ION

AL

AM

PL

IFIE

RS

SLO

S181C

− F

EB

RU

AR

Y 1997 −

RE

VIS

ED

DE

CE

MB

ER

2009

Template R

elease Date: 7−

11−94

4P

OS

T O

FF

ICE

BO

X 655303 D

ALLA

S, T

EX

AS

75265•

equivalent schematic

Q1

IN−

IN+

Q2 D1

Q7

Q5

Q6

Q9

Q10

C2

R4

Q14

Q4

Q3

R1

Q8

R2

Q11

R3

C1

Q12

D2

Q13

Q15

Q16

Q19

Q20

Q17

R6

VCC −

VCC +

R8

C3Q18

R7

R5 C4

Q21

C5

R9 R10

Q22 Q26 Q27

Q31 R14

Q29

C6Q25

Q30

R11

Q23

Q28

Q24

D3

OUTR13

R12

OFFSET N1(see Note A)

OFFSET N2(see Note A)

NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2071x devices.

TL

E207x, T

LE

207xAE

XC

AL

IBU

R L

OW

-NO

ISE

HIG

H-S

PE

ED

JFE

T-INP

UT

OP

ER

AT

ION

AL

AM

PL

IFIE

RS

SLO

S181C

− F

EB

RU

AR

Y 1997 −

RE

VIS

ED

DE

CE

MB

ER

2009

PO

ST

OF

FIC

E B

OX

655303 DA

LLAS

, TE

XA

S 75265

•5

equivalent schematic (continued)

ACTUAL DEVICE COMPONENT COUNT

COMPONENT TLE2071 TLE2072 TLE2074

Transistors 33 57 114

Resistors 25 37 74

Diodes 8 5 10

Capacitors 6 11 22


�



absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†

Supply voltage, VCC+ (see Note 1) 19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply voltage, VCC− (see Note 1) −19 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input voltage range, VID (see Note 2) VCC+ to VCC−. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input voltage range, VI (any input) VCC+ to VCC−. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input current, II (each input) ±1 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output current, IO (each output) ±80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current into VCC+ 160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current out of VCC− 160 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package thermal impedance, θJA (see Notes 4 and 5): D package 97.1°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .

DW package 57.3°C/W. . . . . . . . . . . . . . . . . . . . . . . . N package 79.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . P package 84.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .

Package thermal impedance, θJC (see Notes 4 and 5): FK package 5.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . J package 15.1°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . JG package 14.5°C/W. . . . . . . . . . . . . . . . . . . . . . . . . U package 14.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . W package 10°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I suffix −40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M suffix −55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package 260°C. . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J, JG, U, or W package 300°C. . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC −.2. Differential voltages are at the noninverting input with respect to the inverting input.3. The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum

dissipation rate is not exceeded.4. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable

ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.5. The package thermal impedance is calculated in accordance with JESD 51-7 (plastic) or MIL-STD-883 Method 1012 (ceramic).

recommended operating conditions

C SUFFIX I SUFFIX M SUFFIXUNIT

MIN MAX MIN MAX MIN MAXUNIT

Supply voltage, VCC± ±2.25 ±19 ±2.25 ±19 ±2.25 ±19 V

Common mode input voltage VVCC ± = ±5 V −0.9 5 −0.8 5 −0.8 5

VCommon-mode input voltage, VIC VCC ± = ±15 V −10.9 15 −10.8 15 −10.8 15V

Operating free-air temperature, TA 0 70 −40 85 −55 125 °C



�



TLE2071C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unlessotherwise noted)

PARAMETER TEST CONDITIONS T †TLE2071C TLE2071AC

UNITPARAMETER TEST CONDITIONS TA†

MIN TYP MAX MIN TYP MAXUNIT

V Input offset voltage25°C 0.34 4 0.3 2

mVVIO Input offset voltageVIC = 0, VO = 0, Full range 6 4

mV

αVIOTemperature coefficientof input offset voltage

VIC 0, VO 0,RS = 50 Ω

Full range 3.2 29 3.2 29 μV/°C

I Input offset current25°C 5 100 5 100 pA

IIO Input offset currentVIC = 0, VO = 0, Full range 1.4 1.4 nA

I Input bias current

VIC = 0, VO = 0,See Figure 4 25°C 15 175 15 175 pA

IIB Input bias currentFull range 5 5 nA

5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9

VVICRCommon mode inputvoltage range RS = 50 Ω

5 5Vvoltage range

Full range5to

5toFull range to

−0.9to

−0.9

I 200 A25°C 3.8 4.1 3.8 4.1

IO = −200 μAFull range 3.7 3.7

VMaximum positive peak

I 2 mA25°C 3.5 3.9 3.5 3.9

VVOM +Maximum positive peakoutput voltage swing IO = −2 mA

Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3

IO = −20 mAFull range 1.5 1.5

I 200 A25°C −3.5 −4.2 −3.5 −4.2

IO = 200 μAFull range −3.4 −3.4

VMaximum negative peak

I 2 mA25°C −3.7 −4.1 −3.7 −4.1

VVOM −Maximum negative peakoutput voltage swing IO = 2 mA

Full range −3.6 −3.6V

I 20 mA25°C −1.5 −2.4 −1.5 −2.4

IO = 20 mAFull range −1.5 −1.5

R 600 Ω25°C 80 91 80 91

RL = 600 ΩFull range 79 79

ALarge-signal differential

V ± 2 3 V R 2 kΩ25°C 90 100 90 100

dBAVDLarge signal differentialvoltage amplification VO = ± 2.3 V RL = 2 kΩ

Full range 89 89dB

R 10 kΩ25°C 95 106 95 106

RL = 10 kΩFull range 94 94

ri Input resistance VIC = 0 25°C 1012 1012 Ω

ci Input capacitanceVIC = 0,See Figure 5

Commonmode

25°C 11 11pFci Input capacitance

See Figure 5Differential 25°C 2.5 2.5

pF

zoOpen-loop output impedance

f = 1 MHz 25°C 80 80 Ω

CMRRCommon-mode VIC = VICRmin, 25°C 70 89 70 89

dBCMRRCommon moderejection ratio

VIC = VICRmin,VO = 0, RS = 50 Ω Full range 68 68

dB

kSupply-voltage rejection VCC ± = ±5 V to ±15 V, 25°C 82 99 82 99

dBkSVRSupply voltage rejectionratio(ΔVCC± /ΔVIO)

VCC ± = ±5 V to ±15 V,VO = 0, RS = 50 Ω Full range 80 80

dB

† Full range is 0°C to 70°C.


�



TLE2071C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unlessotherwise noted) (continued)




I Supply current V 0 No load25°C 1.35 1.6 2.2 1.35 1.6 2.2

mAICC Supply current VO = 0, No loadFull range 2.2 2.2

mA

IShort-circuit output

V 0VID = 1 V

25°C−35 −35

mAIOSShort circuit output current VO = 0

VID = −1 V25°C

45 45mA


TLE2071C operating characteristics at specified free-air temperature, VCC± = ±5 V




25°C 35 35

SR+ Positive slew rateVO(PP) = ±2.3 V,A 1 R 2 kΩ

Fullrange

23 23V/μs

AVD = −1, RL = 2 kΩ,CL = 100 pF, See Figure 1 25°C 38 38

SR− Negative slew rateCL = 100 pF, See Figure 1

Fullrange

23 23V/μs

t Settling time

AVD = −1,2-V step,

To 10 mV

25°C0.25 0.25

sts Settling time2-V step,RL = 1 kΩ,CL = 100 pF To 1 mV

25°C0.4 0.4

μs

VEquivalent input noise f = 10 Hz

25°C48 85 48 85

nV/√HzVnEquivalent input noisevoltage f = 10 kHz

25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peak equivalent

RS 20 Ω,See Figure 3

f = 10 Hz to10 kHz

25°C6 6

μVVN(PP)Peak to peak equivalentinput noise voltage f = 0.1 Hz to

10 Hz

25°C0.6 0.6

μV

InEquivalent input noisecurrent

VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz

THD NTotal harmonic distortion

VO(PP) = 5 V, AVD = 10,f 1 kHz R 2 kΩ 25°C 0 013% 0 013%THD + N

Total harmonic distortionplus noise f = 1 kHz, RL = 2 kΩ,

RS = 25 Ω25°C 0.013% 0.013%

B Unity gain bandwidthVI = 10 mV, RL = 2 kΩ,

25°C 9 4 9 4 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 9.4 9.4 MHz

BMaximum output-swing VO(PP) = 4 V, AVD = −1,

25°C 2 8 2 8 MHzBOMMaximum output swingbandwidth

VO(PP) = 4 V, AVD = 1,RL = 2 kΩ , CL = 25 pF 25°C 2.8 2.8 MHz

φ Phase margin at unity VI = 10 mV, RL = 2 kΩ,25°C 56° 56°φm

Phase margin at unitygain

VI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2

25°C 56° 56°




�









mV


VIC 0, VO 0,RS = 50 Ω







15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.9to

−10.9

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9


Full range 13.4 13.4V

I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109

dBAVDLarge signal differentialvoltage amplification VO = ±10 V RL = 2 kΩ

Full range 89 89dB

R 10 kΩ25°C 95 118 95 118




Commonmode

25°C 7.5 7.5pFci Input capacitance


pF


f = 1 MHz 25°C 80 80 Ω




dB


dBkSVRSupply voltage rejectionratio (ΔVCC± /ΔVIO)


dB



�









mA


V 0VID = 1 V

25°C−30 −45 −30 −45

mAIOSShort-circuit output current

VO = 0VID = −1 V

25°C30 48 30 48

mA






25°C 30 40 30 40

SR+ Positive slew rateVO(PP) = 10 V, AVD = −1,R 2 kΩ C 100 pF

Fullrange

27 27V/μs

RL = 2 kΩ, CL = 100 pF,See Figure 1 25°C 30 45 30 45

SR− Negative slew rateSee Figure 1

Fullrange

27 27V/μs

t Settling time


To 10 mV

25°C0.4 0.4

sts Settling time10-V step, RL = 1kΩ,CL = 100 pF To 1 mV

25°C1.5 1.5

μs


25°C48 85 48 85

nV√HzVnEquivalent input noisevoltage f = 10 kHz

25°C12 17 12 17

nV√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6

VVN(PP)Peak to peak equivalentinput noise voltage f = 0.1 Hz to

25°C0 6 0 6

μVp g f = 0.1 Hz to10 Hz 0.6 0.6

IEquivalent input noise

V 0 f 10 kHz 25°C 2 8 2 8 fA/√HzInEquivalent input noisecurrent VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




RS = 25 Ω25°C 0.008% 0.008%


25°C 8 10 8 10 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 8 10 8 10 MHz


25°C 478 637 478 637 kHzBOMMaximum output swingbandwidth

VO(PP) = 20 V, AVD = 1,RL = 2 kΩ, CL = 25 pF 25°C 478 637 478 637 kHz




25°C 57° 57°




�



TLE2071I electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless otherwisenoted)

PARAMETER TEST CONDITIONS T †TLE2071I TLE2071AI




mVVIO Input offset voltageVIC = 0, VO = 0, Full range 7.6 5.6

mV


VIC 0, VO 0,RS = 50 Ω,



IIO Input offset currentVIC = 0, VO = 0, Full range 5 5 nA




5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100

dBAVDLarge signal differentialvoltage amplification VO = ±2.3 V RL = 2 kΩ

Full range 89 89dB

R 10 kΩ25°C 95 106 95 106




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB

† Full range is −40°C to 85°C.


�



TLE2071I electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless otherwisenoted) (continued)






mA


V 0VID = 1 V

25°C−35 −35


VID = −1 V25°C

45 45mA


TLE2071I operating characteristics at specified free-air temperature, VCC± = ±5 V




25°C 35 35


Fullrange

22 22V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


25°C0 6 0 6

μVp g f = 0.1 Hz to10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




RS = 25 Ω25°C 0.013% 0.013%






φ Phase margin at unity gainVI = 10 mV, RL = 2 kΩ,

25°C 56° 56°φm Phase margin at unity gainVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 56° 56°




�



TLE2071I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unlessotherwise noted)






mV


VIC 0, VO 0,RS = 50 Ω,







15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.8to

−10.8

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ± 10 V R 2 kΩ25°C 90 109 90 109

dBAVDLarge signal differentialvoltage amplification VO = ± 10 V RL = 2 kΩ

Full range 89 89dB

R 10 kΩ25°C 95 118 95 118




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω

CMRRCommon-mode

VIC = VICRmin,V 0

25°C 80 98 80 98dBCMRR

Common moderejection ratio

VO = 0,RS = 50 Ω Full range 79 79

dB




dB



�



TLE2071I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unlessotherwise noted) (continued)






mA


V 0VID = 1 V

25°C−30 −45 −30 −45


VO = 0VID = −1 V

25°C30 48 30 48

mA






25°C 30 40 30 40

SR+ Positive slew rateVO(PP) = ±10 V,A 1 R 2 kΩ

Fullrange

24 24V/μs

AVD = −1, RL = 2 kΩ,CL = 100 pF See Figure 1 25°C 30 45 30 45


Fullrange

24 24V/μs

t Settling time


To 10 mV25°C

0.4 0.4μsts Settling time 10-V step,

RL = 1kΩ,CL = 100 pF

To 1 mV25°C

1.5 1.5μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

V ( )Peak-to-peak equivalent


f = 10 Hz to10 kHz

25°C6 6

μVVN(PP)Peak to peak equivalentinput noise voltage

g

f = 0.1 Hz to10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz

THD + NTotal harmonic distortion


Total harmonic distortionplus noise

f = 1 kHz, RL = 2 kΩ,RS = 25 Ω

25°C 0.008% 0.008%


25°C 8 10 8 10 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2

25°C 8 10 8 10 MHz

BOMaximum output-swing VO(PP) = 20 V, AVD = −1,


VO(PP) = 20 V, AVD = 1,RL = 2 kΩ, CL = 25 pF

25°C 478 637 478 637 kHz


25°C 57° 57°φm Phase margin at unity gainVI 10 mV, RL 2 kΩ,CL = 25 pF, See Figure 2 25°C 57° 57°




�



TLE2071M electrical characteristics at specified free-air temperature, VCC± = ±5 V (unlessotherwise noted)

PARAMETER TEST CONDITIONS T †TLE2071M TLE2071AM





mV


VIC 0, VO 0,RS = 50 Ω,

Full range 3.2 29� 3.2 29� μV/°C






5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.3 3.3V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 88 88dB

R 10 kΩ25°C 95 106 95 106




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB

† Full range is −55°C to 125°C.‡ ∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.


�









mA


V 0VID = 1 V

25°C−35 −35


VO = 0VID = −1 V

25°C45 45

mA


TLE2071M operating characteristics at specified free-air temperature, VCC± = ±5 V




25°C 35 35


Fullrange

20� 20�V/μs



Fullrange

20� 20�V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85� 48 85�


25°C12 17� 12 17�

nV/√Hz


RS = 20 Ω,See Figure 3

f = 10 Hz to10 kHz

25°C6 6

VVN(PP)Peak-to-peak equivalentinput noise voltage

g

f = 0.1 Hz to25°C

0 6 0 6

μVinput noise voltage f = 0.1 Hz to

10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.013% 0.013%






φPhase margin at unity VI = 10 mV, RL = 2 kΩ,

25°C 56° 56°φmPhase margin at unitygain

VI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 56° 56°

† Full range is −55°C to 125°C.‡ ∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.



�









mV


VIC 0, VO 0,RS = 50 Ω

Full range 3.2 29∗ 3.2 29∗ μV/°C






15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.9to

−10.9

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.6 −13.6


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 88 88dB

R 10 kΩ25°C 95 118 95 118




Commonmode



pF

zoOpen-loop outputimpedance

f = 1 MHz 25°C 80 80 Ω




dB




dB

∗On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.† Full range is −55°C to 125°C.


�



TLE2071M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unlessotherwise noted) (continued)






mA

I Short circuit output current V 0VID = 1 V

25°C−30 −45 −30 −45

mAIOS Short-circuit output current VO = 0VID = −1 V

25°C30 48 30 48

mA






25°C 30 40 30 40


Fullrange

22 22V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.4 0.4


25°C1.5 1.5

μs


25°C48 85∗ 48 85∗


25°C12 17∗ 12 17∗ nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


25°C0 6 0 6

μVp g f = 0.1 Hz to10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.008% 0.008%


25°C 8∗ 10 8∗ 10 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 8∗ 10 8∗ 10 MHz


25°C 478∗ 637 478∗ 637 kHzBOMMaximum output swingbandwidth

VO(PP) = 20 V, AVD = 1,RL = 2 kΩ, CL = 25 pF 25°C 478∗ 637 478∗ 637 kHz







�



TLE2071Y electrical characteristics at VCC± = ±15 V, TA = 25°C

PARAMETER TEST CONDITIONSTLE2071Y

UNITPARAMETER TEST CONDITIONSMIN TYP MAX

UNIT

VIO Input offset voltage VIC = 0, VO = 0, RS = 50 Ω 0.49 4 mV

IIO Input offset currentV 0 V 0 See Figure 4

6 100 pA

IIB Input bias currentVIC = 0, VO = 0, See Figure 4

20 175 pA

15 15VICR Common-mode input voltage range RS = 50 Ω

15to

15to VVICR Common mode input voltage range RS = 50 Ω to

−11to

11.9V

IO = −200 μA 13.8 14.1

VOM + Maximum positive peak output voltage swing IO = −2 mA 13.5 13.9 VVOM + Maximum positive peak output voltage swing

IO = −20 mA 11.5 12.3

V

IO = 200 μA −13.8 −14.2

VOM − Maximum negative peak output voltage swing IO = 2 mA −13.5 −14 VVOM − Maximum negative peak output voltage swing

IO = 20 mA −11.5 −12.4

V

RL = 600 Ω 80 96

AVD Large-signal differential voltage amplification VO = ±10 V RL = 2 kΩ 90 109 dBAVD Large signal differential voltage amplification VO ±10 V

RL = 10 kΩ 95 118

dB

ri Input resistance VIC = 0 1012 Ω

c Input capacitanceVO = 0, Common mode 7.5

pFci Input capacitanceVO = 0,See Figure 5 Differential 2.5

pF

zo Open-loop output impedance f = 1 MHz 80 Ω

CMRR Common-mode rejection ratioVIC = VICRmin, VO = 0,RS = 50 Ω 80 98 dB

kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO)VCC ± = ±5 V to ±15 V, VO = 0,RS = 50 Ω 82 99 dB

ICC Supply current VO = 0, No load 1.35 1.7 2.2 mA

I Short circuit output current V 0VID = 1 V −30 −45

mAIOS Short-circuit output current VO = 0VID = −1 V 30 48

mA


�







V Input offset voltage25°C 0.9 6 0.65 3.5


mV


VIC 0, VO 0,RS = 50 Ω







5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.9to

−0.9

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 89 89dB

R 10 kΩ25°C 95 106 95 106




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB


dBkSVRSupply voltage rejectionratio(ΔVCC± /ΔVIO)


dB




�



TLE2072C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unlessotherwise noted)(continued)

PARAMETER TEST CONDITIONS TTLE2072C TLE2072AC

UNITPARAMETER TEST CONDITIONS TA MIN TYP MAX MIN TYP MAXUNIT

ISupply current

V 0 No load25°C 2.7 2.9 3.9 2.7 2.9 3.9

mAICCSupply current(both channels) VO = 0, No load

Full range 3.9 3.9mA

ax Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB


V 0VID = 1 V

25°C−35 −35


VID = −1 V25°C

45 45mA





25°C 35 35


Fullrange

22 22V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peak equiva-lent


f = 10 Hz to10 kHz

25°C6 6

VVN(PP) lentinput noise voltage f = 0.1 Hz to

10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic distor-tion

VO(PP) = 5 V, AVD = 10,f 1 kH R 2 kΩ 25°C 0 013% 0 013%THD + N tion

plus noisef = 1 kHz, RL = 2 kΩ,RS = 25 Ω

25°C 0.013% 0.013%









25°C 56° 56°



�









mV


VIC 0, VO 0,RS = 50 Ω







15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.9to

−10.9

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 89 89dB

R 10 kΩ25°C 95 118 95 118




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB




�




PARAMETER TEST CONDITIONS TTLE2072C TLE2072AC


ISupply current

V 0 No load25°C 2.7 3.1 3.9 2.7 3.1 3.9





25°C−30 −45 −30 −45


25°C30 48 30 48

mA





25°C 28 40 28 40

SR+ Positive slew rateVO(PP) = 10 V,A 1 R 2 kΩ

Fullrange

25 25V/μs

AVD = −1, RL = 2 kΩ,CL = 100 pF, See Figure 1 25°C 30 45 30 45


Fullrange

25 25V/μs

t Settling time


To 10 mV

25°C0.4 0.4


25°C1.5 1.5

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peakequivalent input noise


f = 10 Hz to10 kHz

25°C6 6

VVN(PP) equivalent input noisevoltage f = 0.1 Hz to

10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic

VO(PP) = 20 V, AVD = 10,f 1 kH R 2 kΩ 25°C 0 008% 0 008%THD + N

Total harmonicdistortion plus noise f = 1 kHz, RL = 2 kΩ,

RS = 25 Ω25°C 0.008% 0.008%









25°C 57° 57°



�









mV


VIC 0, VO 0,RS = 50 Ω,







5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 89 89dB

R 10 kΩ25°C 95 106 95 106




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB




�




PARAMETER TEST CONDITIONS TTLE2072I TLE2072AI


ISupply current

V = 0 No load25°C 2.7 2.9 3.9 2.7 2.9 3.9

mAICCSupply current(both channels)

VO = 0, No loadFull range 3.9 3.9

mA



25°C−35 −35


25°C45 45

mA





25°C 35 35


Fullrange

20 20V/μs



Fullrange

20 20V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peak equivalent input


f = 10 Hz to10 kHz

25°C6 6

VVN(PP) equivalent inputnoise voltage f = 0.1 Hz to

25°C0 6 0 6

μVnoise voltage f = 0.1 Hz to

10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic


Total harmonic distortion plus noise f = 1 kHz, RL = 2 kΩ,

RS = 25 Ω25°C 0.013% 0.013%



BMaximum output- VO(PP) = 4 V, AVD = −1,

25°C 2 8 2 8 MHzBOMMaximum outputswing bandwidth





25°C 56° 56°



�









mV


VIC 0, VO 0,RS = 50 Ω,







15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.8to

−10.8

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 89 89dB

R 10 kΩ25°C 95 118 95 118




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB




�



TLE2072I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unlessotherwise noted)(continued)

PARAMETER TEST CONDITIONS TTLE2072I TLE2072AI


ICCSupply current

VO = 0 No load25°C 2.7 3.1 3.9 2.7 3.1 3.9

mAICCSupply current(both channels)

VO = 0, No loadFull range 3.9 3.9

mA



25°C−30 −45 −30 −45


25°C30 48 30 48

mA





25°C 28 40 28 40


Fullrange

22 22V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.4 0.4

sts Settling time10-V step,RL = 1kΩ,CL = 100 pF To 1 mV

25°C1.5 1.5

μs

VEquivalent input f = 10 Hz

25°C48 85 48 85

nV/√HzVnEquivalent inputnoise voltage f = 10 kHz

25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 0 Hz to6 6

VPeak-to-peak equivalent input


f = 0 Hz to10 kHz

25°C6 6


10 Hz

25°C0.6 0.6

μV

InEquivalent inputnoise current

VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic



RS = 25 Ω25°C 0.008% 0.008%



BMaximum output- VO(PP) = 20 V, AVD = −1,

25°C 478 637 478 637 kHzBOMMaximum outputswing bandwidth


φ Phase margin at VI = 10 mV, RL = 2 kΩ,25°C 57° 57°φm

Phase margin atunity gain


25°C 57° 57°



�








mVVIO Input offset voltageVIC = 0, VO = 0, Full range 10.5 8

mV


VIC 0, VO 0,RS = 50 Ω,

Full range 2.3 25∗ 2.3 25∗ μV/°C






5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.3 3.3V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 88 88dB

R 10 kΩ25°C 95 106 95 106




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




�







kSVRSupply-voltage rejectionratio (ΔVCC± /ΔVIO)

VCC ± = ±5 V to ±15 V,VO = 0, RS = 50 Ω Full range 80 80 dB

ISupply current

V 0 No load25°C 2.7 2.9 3.6 2.7 2.9 3.6





V 0VID = 1 V

25°C−35 −35


VO = 0VID = −1 V

25°C45 45

mA






25°C 35 35


Fullrange

18∗ 18∗ V/μs



Fullrange

18∗ 18∗ V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85∗ 48 85∗


25°C12 17∗ 12 17∗ nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peakequivalent input


f = 10 Hz to10 kHz

25°C6 6


25°C0 6 0 6


10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic


Total harmonicdistortion plus noise

f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.013% 0.013%











�








mVVIO Input offset voltageVIC = 0, VO = 0, Full range 10.5 8

mV


VIC 0, VO 0,RS = 50 Ω

Full range 2.4 25∗ 2.4 25∗ μV/°C






15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to−11

to−11.9

to−11

to−11.9


15 15Vvoltage range

Full range15to

15toFull range to

−10.8to

−10.8

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.6 −13.6


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 89 89dB

R 10 kΩ25°C 95 118 95 118




Commonmode



pF


f = 1 MHz 25°C 80 80 Ω




dB




dB




�







ISupply current

V 0 No load25°C 2.7 3.1 3.6 2.7 3.1 3.6





V 0VID = 1 V

25°C−30 −45 −30 −45

mAIOSShort circuit outputcurrent VO = 0

VID = −1 V25°C

30 48 30 48mA






25°C 28 40 28 40


Fullrange

20 20V/μs



Fullrange

20 20V/μs

t Settling time


To 10 mV

25°C0.4 0.4


25°C1.5 1.5

μs


25°C48 85∗ 48 85∗


25°C12 17∗ 12 17∗ nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6

VPeak-to-peakequivalent input


f = 10 Hz to10 kHz

25°C6 6

VVN(PP) equivalent input noise voltage f = 0.1 Hz to

25°C0 6 0 6


10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA /√Hz

THD NTotal harmonic



RS = 25 Ω25°C 0.008% 0.008%


25°C 8∗ 10 8∗ 10 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 8∗ 10 8∗ 10 MHz

BMaximumoutput swing

VO(PP) = 20 V, AVD = −1,25°C 478∗ 637 478∗ 637 kHzBOM output-swing

bandwidth

VO(PP) = 20 V, AVD = 1,RL = 2 kΩ, CL = 25 pF 25°C 478∗ 637 478∗ 637 kHz




25°C 57° 57°



�



TLE2072Y electrical characteristics at VCC± = ±15 V, TA = 25°C



UNIT

VIO Input offset voltage VIC = 0, VO = 0, RS = 50 Ω 1.1 6 mV

IIO Input offset currentV 0 V 0 See Figure 4

6 100 pA

IIB Input bias currentVIC = 0, VO = 0, See Figure 4

20 175 pA


15to


−11to

11.9V

IO = −200 μA 13.8 14.1


IO = −20 mA 11.5 12.3

V

M i ti kIO = 200 μA −13.8 −14.2

VOM −Maximum negative peakoutput voltage swing

IO = 2 mA −13.5 −14 VVOM − output voltage swingIO = 20 mA −11.5 −12.4

V

RL = 600 Ω 80 96

AVD Large-signal differential voltage amplification VO = ± 10 V RL = 2 kΩ 90 109 dBAVD Large signal differential voltage amplification VO ± 10 V

RL = 10 kΩ 95 118

dB


c Input capacitanceVIC = 0, Common mode 7.5

pFci Input capacitanceVIC = 0,See Figure 5 Differential 2.5

pF


CMRR Common-mode rejection ratio VIC = VICRmin, VO = 0, RS = 50 Ω 80 98 dB

kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO)VCC ± = ±5 V to ±15 V, VO = 0,RS = 50 Ω 82 99 dB

ICC Supply current (both channels) VO = 0, No load 2.7 3.1 3.9 mA



mA



�







V Input offset voltage25°C −1.6 5 −0.5 3


mV


VIC 0, VO 0,RS = 50 Ω

Full range 10.1 30 10.1 30 μV/°C

I Input offset current25°C 15 100 15 100

pAIIO Input offset currentVIC = 0, VO = 0, Full range 1400 1400

pA


VIC = 0, VO = 0,See Figure 4 25°C 20 175 20 175

pAIIB Input bias currentFull range 5000 5000

pA

5 5 5 525°C

5to

5to

5to

5 to

VCommon-mode input

R 50 Ω

25 C to−1

to−1.9

to−1

to−1.9


5 5Vvoltage range

Full range5to

5toFull range to

−0.9to

−0.9

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 89 89dB

R 10 kΩ25°C 95 106 95 106



cInput Common mode

V 0 See Figure 525°C 11 11

pFciInputcapacitance Differential

VIC = 0, See Figure 525°C 2.5 2.5

pF

zo Open-loop output impedance f = 1 MHz 25°C 80 80 Ω

CMRR Common mode rejection ratioVIC = VICRmin, 25°C 70 89 70 89

dBCMRR Common-mode rejection ratioVIC = VICRmin,VO = 0, RS = 50 Ω Full range 68 68

dB




dB



�







ISupply current

V 0 No load25°C 5.2 6.3 7.5 5.2 6.3 7.5

mAICCSupply current( four amplifiers ) VO = 0, No load


Crosstalk attenuation VIC = 0, RL = 2 kΩ 25°C 120 120 dB


V 0VID = 1 V

25°C−35 −35


VO = 0VID = −1 V

25°C45 45

mA






25°C 35 35


Fullrange

22 22V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6

μVVN(PP)Peak to peak equivalentinput noise voltage f = 0.1Hz to

10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ,RS = 25 Ω

25°C 0.013% 0.013%









25°C 56° 56°




�









mV


VIC 0, VO 0,RS = 50 Ω

Full range 10.1 30 10.1 30 μV/°C

I Input offset current25°C 15 100 15 100

pAIIO Input offset currentVIC = 0, VO = 0, Full range 1400 1400

pA


VIC = 0, VO = 0,See Figure 4 25°C 25 175 25 175

pAIIB Input bias currentFull range 5000 5000

pA

15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to

−11to

−11.9to

−11to

−11.9VVICR

Common mode inputvoltage range RS = 50 Ω

15 15Vvoltage range

Full range15to

15toFull range to

−10.9to

−10.9

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.7 −14 −13.7 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 89 89dB

R 10 kΩ25°C 95 118 95 118



ciInputcapacitance

Commonmode VIC = 0, See Figure 5

25°C 7.5 7.5pFci capacitance

Differential

VIC = 0, See Figure 5

25°C 2.5 2.5

pF





dB

kSupply-voltage rejection ratio VCC ± = ±5 V to ±15 V, 25°C 82 99 82 99

dBkSVRSupply voltage rejection ratio(ΔVCC± /ΔVIO)


dB



�







ISupply current

V 0 No load25°C 5.2 6.5 7.5 5.2 6.5 7.5





V 0VID = 1 V

25°C−30 −45 −30 −45


VO = 0VID = −1 V

25°C30 48 30 48

mA






25°C 25 40 25 40


Fullrange

22 22V/μs



Fullrange

25 25V/μs

t Settling time


To 10 mV

25°C0.4 0.4


25°C1.5 1.5

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.008% 0.008%









25°C 57° 57°




�









mV


VIC 0, VO 0,RS = 50 Ω

Full range 10.1 30 10.1 30 μV/°C






5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to

−1to

−1.9to

−1to

−1.9VVICR


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.4 3.4V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 89 89dB

R 10 kΩ25°C 95 106 95 106



cInput Common mode



VIC = 0, See Figure 525°C 2.5 2.5

pF




dB




dB



�







ISupply current

V 0 No load25°C 5.2 6.3 7.5 5.2 6.3 7.5





25°C−35 −35


25°C45 45

mA






25°C 35 35


Fullrange

20 20V/μs



Fullrange

20 20V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ,RS = 25 Ω

25°C 0.013% 0.013%









25°C 56° 56°




�









mV


VIC 0, VO 0,RS = 50 Ω

Full range 10.1 30 10.1 30 μV/°C






15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to

−11to

−11.9to

−11to

−11.9VVICR


15 15Vvoltage range

Full range15to

15toFull range to

−10.8to

−10.8

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.7 −13.7


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 89 89dB

R 10 kΩ25°C 95 118 95 118



ciInputcapacitance

Commonmode VIC = 0, See Figure 5

25°C 7.5 7.5pFci

pcapacitance

DifferentialVIC = 0, See Figure 5

25°C 2.5 2.5pF


f = 1 MHz 25°C 80 80 Ω


dBCMRRCommon mode rejection ratio


dB


dBkSVRSupply voltage rejectionratio (ΔVCC±

�

/ΔVIO)VCC ± = ±5 V to ±15 V,VO = 0, RS = 50 Ω Full range 80 80

dB



�



TLE2074I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unlessotherwise noted) (continued)




ISupply current

V 0 No load25°C 5.2 6.5 7.5 5.2 6.5 7.5





V 0VID = 1 V

25°C−30 −45 −30 −45


VO = 0VID = −1 V

25°C30 48 30 48

mA






25°C 25 40 25 40


Fullrange

19 19V/μs



Fullrange

22 22V/μs

t Settling time


To 10 mV

25°C0.4 0.4

sts Settling time10-V step,RL = 1kΩ,CL = 100 pF To 1 mV

25°C1.5 1.5

μs


25°C48 85 48 85


25°C12 17 12 17

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


10 Hz

25°C0.6 0.6

μV


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.008% 0.008%







25°C 57° 57°φm Phase margin at unity gainVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2

25°C 57° 57°




�









mV


VIC 0, VO 0,RS = 50Ω

Full range 10.1 30� 10.1 30� μV/°C






5 5 5 525°C

5to

5to

5to

5to

VCommon-mode input

R 50 Ω

25 C to

−1to

−1.9to

−1to

−1.9VVICR


5 5Vvoltage range

Full range5to

5toFull range to

−0.8to

−0.8

I 200 A25°C 3.8 4.1 3.8 4.1



I 2 mA25°C 3.5 3.9 3.5 3.9


Full range 3.3 3.3V

I 20 mA25°C 1.5 2.3 1.5 2.3


I 200 A25°C −3.8 −4.2 −3.8 −4.2



I 2 mA25°C −3.5 −4.1 −3.5 −4.1



I 20 mA25°C −1.5 −2.4 −1.5 −2.4


R 600 Ω25°C 80 91 80 91



V ±2 3 V R 2 kΩ25°C 90 100 90 100


Full range 88 88dB

R 10 kΩ25°C 95 106 95 106



cInput Common mode



VIC = 0, See Figure 525°C 2.5 2.5

pF




dB




dB

† Full range is −55°C to 125°C.‡ On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.


�







ISupply current

V 0 No load25°C 5.2 6.3 7.5 5.2 6.3 7.5





25°C−35 −35


25°C45 45

mA






25°C 35 35


Fullrange

18� 18�V/μs



Fullrange

18� 18�V/μs

t Settling time


To 10 mV

25°C0.25 0.25


25°C0.4 0.4

μs


25°C48 85� 48 85�


25°C12 17� 12 17�

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6


25°C0 6 0 6

μVp g f = 0.1 Hz to10 Hz 0.6 0.6


VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




f = 1 kHz, RL = 2 kΩ, RS = 25 Ω

25°C 0.013% 0.013%





VO(PP) = 4 V, AVD = 1,RL = 2 kΩ, CL = 25 pF 25°C 2.8 2.8 MHz

fPhase margin at unity VI = 10 mV, RL = 2 kΩ,

25°C 56° 56°fmPhase margin at unitygain


25°C 56° 56°




�









mV


VIC 0, VO 0,RS = 50 Ω

Full range 10.1 30� 10.1 30� μV/°C






15 15 15 1525°C

15to

15to

15to

15to

VCommon-mode input

R 50 Ω

25 C to

−11to

−11.9to

−11to

−11.9VVICR


15 15Vvoltage range

Full range15to

15toFull range to

−10.8to

−10.8

I 200 A25°C 13.8 14.1 13.8 14.1



I 2 mA25°C 13.5 13.9 13.5 13.9



I 20 mA25°C 11.5 12.3 11.5 12.3


I 200 A25°C −13.8 −14.2 −13.8 −14.2

IO = 200 μAFull range −13.6 −13.6


I 2 mA25°C −13.5 −14 −13.5 −14



I 20 mA25°C −11.5 −12.4 −11.5 −12.4


R 600 Ω25°C 80 96 80 96



V ±10 V R 2 kΩ25°C 90 109 90 109


Full range 88 88dB

R 10 kΩ25°C 95 118 95 118



cInput Common mode

V 0 See Figure 525°C 7.5 7.5


VIC = 0, See Figure 525°C 2.5 2.5

pF




dB


dBkSVRSupply voltage rejection ratio (ΔVCC± /ΔVIO)


dB



�







ISupply current

V 0 No load25°C 5.2 6.5 7.5 5.2 6.5 7.5





25°C−30 −45 −30 −45


25°C30 48 30 48

mA






25°C 25 40 25 40


Fullrange

17 17V/μs



Fullrange

20 20V/μs

t Settling time


To 10 mV

25°C0.4 0.4

sts Settling time10 V step, RL = 1kΩ,CL = 100 pF To 1 mV

25°C1.5 1.5

μs


25°C48 85� 48 85�


25°C12 17� 12 17�

nV/√Hz

RS = 20 Ω, f = 10 Hz to6 6



f = 10 Hz to10 kHz

25°C6 6

VVN(PP)Peak to peak equivalentinput noise voltage

g

f = 0.1 Hz to25°C

0 6 0 6

μVp g f = 0.1 Hz to10 Hz 0.6 0.6

IEquivalent input noise

V 0 f 10 kHz 25°C 2 8 2 8 fA/√HzInEquivalent input noisecurrent VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz




RS = 25 Ω25°C 0.008% 0.008%


25°C 8� 10 8� 10 MHzB1 Unity-gain bandwidthVI = 10 mV, RL = 2 kΩ,CL = 25 pF, See Figure 2 25°C 8� 10 8� 10 MHz


25°C 478� 637 478� 637 kHzBOMMaximum output swingbandwidth

VO(PP) = 20 V, AVD = 1,RL = 2 kΩ, CL = 25 pF 25°C 478� 637 478� 637 kHz




25°C 57° 57°




�



TLE2074Y electrical characteristics at VCC± = ±15 V, TA = 25°C (unless otherwise noted)



UNIT

VIO Input offset voltageVIC = 0, VO = 0,RS = 50 Ω 5 mV

IIO Input offset current VIC = 0, VO = 0, 15 100 pA

IIB Input bias current

VIC = 0, VO = 0,See Figure 4 25 175 pA


15to


−11to

11.9V

IO = −200 μA 13.8 14.1


IO = −20 mA 11.5 12.3

V

IO = 200 μA −13.8 −14.2

VOM − Maximum negative peak output voltage swing IO = 2 mA −13.5 −14 VVOM − Maximum negative peak output voltage swing

IO = 20 mA −11.5 −12.4

V

RL = 600 Ω 80 96

AVD Large-signal differential voltage amplification VO = ±10 V RL = 2 kΩ 90 109 dBAVD Large signal differential voltage amplification VO ±10 V

RL = 10 kΩ 95 118

dB


c Input capacitanceCommon mode

V 0 See Figure 57.5

pFci Input capacitanceDifferential

VO = 0, See Figure 52.5

pF


CMRR Common-mode rejection ratioVIC = VICRmin, VO = 0,RS = 50 Ω 80 98 dB

kSVR Supply-voltage rejection ratio (ΔVCC± /ΔVIO)VCC ± = ±5 V to ±15 V,VO = 0, RS = 50 Ω 82 99 dB

ICC Supply current ( four amplifiers ) VO = 0, No load 5.2 6.5 7.5 mA



mA


�



PARAMETER MEASUREMENT INFORMATION

−+

2 kΩ

2 kΩ

RL CL†

VO

VCC +

VCC +

VI −+

10 kΩ

VO

CL†

100Ω

RL

VCC +

VCC +

VI

† Includes fixture capacitance † Includes fixture capacitance

Figure 1. Slew-Rate Test Circuit Figure 2. Unity-Gain Bandwidthand Phase-Margin Test Circuit



�



PARAMETER MEASUREMENT INFORMATION

−+

−+

2 kΩ

VCC + VCC +

VO VO

VCC − VCC −RS RS

Ground Shield

Picoammeters

Figure 3. Noise-Voltage Test Circuit Figure 4. Input-Bias and Offset-Current Test Circuit

−+

VCC +

VO

VCC −

IN−

IN+Cic Cic

Cid

Figure 5. Internal Input Capacitance

typical values

Typical values presented in this data sheet represent the median (50% point) of device parametric performance.

input bias and offset current

At the picoampere bias current level typical of the TLE207x and TLE207xA, accurate measurement of the biascurrent becomes difficult. Not only does this measurement require a picoammeter but test socket leakages caneasily exceed the actual device bias currents. To accurately measure these small currents, Texas Instrumentsuses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied butwith no device in the socket. The device is then inserted in the socket and a second test is performed thatmeasures both the socket leakage and the device input bias current. The two measurements are thensubtracted algebraically to determine the bias current of the device.


�



TYPICAL CHARACTERISTICS

Table of GraphsFIGURE

VIO Input offset voltage Distribution 6, 7, 8

αVIO Temperature coefficient of input offset voltage Distribution 9, 10, 11

IIO Input offset current vs Free-air temperature 12, 13

IIB Input bias currentvs Free-air temperaturevs Total supply voltage

12, 1314

VICR Common-mode input voltage range vs Free-air temperature 15

VO Output voltage vs Differential input voltage 16, 17

VOM + Maximum positive peak output voltage vs Output current 18

VOM − Maximum negative peak output voltage vs Output current 19

VOM Maximum peak output voltagevs Free-air temperaturevs Supply voltage

20, 2122

VO(PP) Maximum peak-to-peak output voltage vs Frequency 23

VO Output voltage vs Settling time 24

AVD Large-signal differential voltage amplificationvs Load resistancevs Free-air temperature

2526, 27

AVD Small-signal differential voltage amplification vs Frequency 28, 29

CMRR Common-mode rejection ratiovs Frequencyvs Free-air temperature

3031

kSVR Supply-voltage rejection ratiovs Frequencyvs Free-air temperature

3233

ICC Supply currentvs Supply voltagevs Free-air temperaturevs Differential input voltage

34, 35, 3637, 38, 3940 − 45

IOS Short-circuit output currentvs Supply voltagevs Elapsed timevs Free-air temperature

464748

SR Slew ratevs Free-air temperaturevs Load resistancevs Differential input voltage

49, 505152

Vn Equivalent Input noise voltage (spectral density) vs Frequency 53

Vn Input referred noise voltagevs Noise bandwidthOver a 10-second time interval

5455

Third-octave spectral noise density vs Frequency bands 56

THD +N Total harmonic distortion plus noise vs Frequency 57, 58

B1 Unity-gain bandwidth vs Load capacitance 59

Gain-bandwidth productvs Free-air temperaturevs Supply voltage

6061

Gain margin vs Load capacitance 62

φm Phase marginvs Free-air temperaturevs Supply voltagevs Load capacitance

636465

Phase shift vs Frequency 28, 29

Noninverting large-signal pulse response vs Time 66

Small-signal pulse response vs Time 67

zo Closed-loop output impedance vs Frequency 68

Crosstalk attenuation vs Frequency 69



�




Figure 6

15

12

6

3

0

27

9

− 4 − 2.4 − 0.8 0.8

Per

cen

tag

e o

f U

nit

s −

% 21

18

24

DISTRIBUTION OF TLE2071INPUT OFFSET VOLTAGE

30

2.4 4

VIO − Input Offset Voltage − mV

VCC = ±15 VTA = 25°CP Package

Figure 7


10

8

4

2

0

18

6

− 4 − 2.4 − 0.8 0.8P

erce

nta

ge

of

Un

its

− % 14

12

16


20

2.4 4

VIO

600 Units Tested From One Wafer LotVCC = ±15 VTA = 25°CP Package

Figure 8


25

20

10

5

0

45

15

− 8 − 4.8 − 1.6 1.6

Per

cen

tag

e o

f U

nit

s −

% 35

30

40


50

4.8 8

VIO

VCC = ±15 VTA = 25°CN Package

Figure 9

15

12

6

3

0

27

9

− 40 − 32 − 24 −16 − 8 0 8

Per

cen

tag

e o

f Am

plif

iers

− %

21

18

24

DISTRIBUTION OF TLE2071 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT

30

16 24 32 40

VCC = ±15 VTA = − 55°C to 125°CP Package

αVIO − Temperature Coefficient − μV/°C


�




Figure 10

15

12

6

3

0

27

9

− 30 − 24 −18 −12 − 6 0 6

Per

cen

tag

e o

f Am

plif

iers

− %

21

18

24


30

12 18 24 30

310 AmplifiersVCC = ±15 VTA = − 55°C to 125°C


P Package

Figure 11

15

12

6

3

0

27

9

− 40 − 32 − 24 −16 − 8 0 8

Per

cen

tag

e o

f Am

plif

iers

− %

21

18

24


30

16 24 32 40

VCC = ±15 VTA = − 55°C to 125°CN Package


Figure 12

0.01

0.00125 45

INPUT BIAS CURRENT ANDINPUT OFFSET CURRENT†

vsFREE-AIR TEMPERATURE

100

65 85 105 125

0.1

1

10

VCC ± = ±5 VVIC = 0VO = 0

IIB

IIO

−75 −55 −35 −15 −5

TA − Free-Air Temperature − °C

IIB a

nd

IIO

− In

pu

t B

ias

and

Off

set

Cu

rren

ts −

nA

I IB

I IO

Figure 13

IIB a

nd

IIO

− In

pu

t B

ias

and

Off

set

Cu

rren

ts −

nA

I IB

I IO

INPUT BIAS CURRENT ANDINPUT OFFSET CURRENT†


25 45 65 85 105 125

0.01

0.001

100

0.1

1

10

VCC ± = ±15 VVIC = 0VO = 0

IIO

IIB

−75 −55 −35 −15 5


† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.



�




Figure 14

104

103

102

100

101

106

IIB −

Inp

ut

Bia

s C

urr

ent

− p

A

INPUT BIAS CURRENTvs

TOTAL SUPPLY VOLTAGE

0 5 10 15 20 25 30 35 40 45

I IB TA = 25°C

TA = −55°C

105 VICmin TA = 125°C

VICmax = VCC +

VCC − Total Supply Voltage (referred to VCC −) − V

Figure 15

VIC

− C

om

mo

n-M

od

e In

pu

t Vo

ltag

e R

ang

e −

VV

ICR

5 25 45

COMMON-MODE INPUT VOLTAGE RANGE†


65 85 105 12

RS = 50 ΩVCC + +0.5

VCC + −0.5

VCC − +3.5

VCC +

VCC − +3

VCC − +2.5

VCC − +2

VICmin

VICmax

− 75 −55 −35 −15


Figure 16

− 5 − 4 − 3 − 2 − 10 0 1

OUTPUT VOLTAGEvs

DIFFERENTIAL INPUT VOLTAGE

2 5

RL = 2 kΩ

RL = 2 kΩ

RL = 10 kΩ

RL = 10 kΩ

VCC ± = ±5 VVIC = 0RS = 50 ΩTA = 25°C

RL = 600 Ω

RL = 600 Ω

− 100

− 200

− 300

− 400

100

200

400

300

0

3 4

VID − Differential Input Voltage − μV

VO

− O

utp

ut

volt

age

− V

OV

Figure 17

− 100

− 200

− 300

− 400− 15 − 10 − 5 50

100

200

400

10 15

RL = 2 kΩ

VCC ± = ±15 V

RL = 10 kΩ

RL = 10 kΩ

RL = 2 kΩ

RL = 600 Ω

RL = 600 Ω

OUTPUT VOLTAGEvs


300

0

VID − Differential Input Voltage − μV

VIC = 0RS = 50 ΩTA = 25°C

VO

− O

utp

ut

volt

age

− V

OV



�




Figure 18

VO

M −

Max

imu

m P

osi

tive

Pea

k O

utp

ut

Volt

age

− V

7.5

6

3

1.5

0

13.5

4.5

0 − 5 −10 −15 − 20 − 25 − 30

10.5

9

12

MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE†

vsOUTPUT CURRENT

15

− 35 − 40 − 45 − 50

VO

M+

TA = −55°C

TA = 25°C

TA = 125°C TA = 85°C

IO − Output Current − mA

VCC ± = ±15 V

Figure 19

− M

axim

um

Neg

ativ

e P

eak

Ou

tpu

t Vo

ltag

e −

V

−7.5

− 6

− 3

−1.5

0

−13.5

− 4.5

0 5 10 15 20 25 30

−10.5

− 9

−12

−15

35 40 45 50VO

M −

MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE†

vsOUTPUT CURRENT

TA = 25°C

TA = 125°C

TA = −55°C

VCC ± = ±15 V

TA = 85°C

IO − Output Current − mA

Figure 20

VO

M −

Max

imu

m P

eak

Ou

tpu

t Vo

ltag

e −

V

0

− 1

− 3

− 4

− 5

4

− 2

5 25 45

2

1

3

MAXIMUM PEAK OUTPUT VOLTAGE†


5

65 85 105 125

VO

M

IO = −200 μA

IO = −2 mA

IO = −20 mA

VCC ± = ±5 V

IO = 20 mA

IO = 2 mA

IO = 200 μA

−75 −55 −35 −15


Figure 21

12.5

12

11

10.5

10

14.5

11.5

5 25 45

|

|

− M

axim

um

Pea

k O

utp

ut

Volt

age

− V

13.5

13

14

15

65 85 105 125

VO

M

MAXIMUM PEAK OUTPUT VOLTAGE†


IO = −20 mA

IO = 20 mA

IO = 2 mA

IO = −200 μAIO = 200 μA

VCC ± = ±15 V

−75 −55 −35 −15


IO = −2 mA




�




Figure 22

VO

M −

Max

imu

m P

eak

Ou

tpu

t Vo

ltag

e −

V

0

− 5

−15

− 20

− 25

20

−10

0 2.5 5 7.5 10 12.5 15

10

5

15

MAXIMUM PEAK OUTPUT VOLTAGEvs

SUPPLY VOLTAGE

25

17.5 20 22.5 25

VO

M

IO = −200 μA

IO = −2 mA

IO = −20 mA

IO = 20 mA

IO = 200 μA

TA = 25°C

|VCC ± | − Supply Voltage − V

IO = 2 mA

Figure 23

VO

(PP

) −

Max

imu

m P

eak-

to-P

eak

Ou

tpu

t Vo

ltag

e −

V

20

5

0

30

10

25

100 k 1 M 10 Mf − Frequency − Hz

VO

(PP

)

15

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE†

vsFREQUENCY

TA = −55°C

TA = 25°C, 125°C

TA = 25°C,125°C

TA = −55°C

VCC ± = ±15 V RL = 2 kΩ

VCC ± = ±5 V

Figure 24

0 0.5 1 1.5 2

VO

− O

utp

ut

Volt

age

− V

OUTPUT VOLTAGEvs

SETTLING TIME

V O

VCC ± = ±15 VRL = 1 kΩCL = 100 pFAV = −1TA = 25°C

1mV

1mV

Rising

Falling

10 mV

10 mV

− 2.5

− 10

− 12.5

10

12.5

− 5

7.5

2.5

− 7.5

5

0

ts − Settling Time − μs

Figure 25

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION

vsLOAD RESISTANCE

115

110

100

95

90

125

105

0.1 1 10 100

120

VCC ± = ±15 V

VCC ± = ±5 V

VIC = 0RS = 50 ΩTA = 25°C

RL − Load Resistance − kΩ

AV

D −

Lar

ge-

Sig

nal

Dif

fere

nti

alA

VD Vo

ltag

e A

mp

lific

atio

n −

dB



�





95

92

86

83

80

107

89

−75 − 55 − 35 −15 5 25 45

101

98

104

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†


110

65 85 105 125

RL = 10 kΩ

RL = 2 kΩ

VCC ± = ±5 V

RL = 600 Ω

VO = ±2.3 V

AV

D −

Lar

ge-

Sig

nal

Dif

fere

nti

alA

VD Vo

ltag

e A

mp

lific

atio

n −

dB

Figure 26

125105−15− 35− 55

105

101

93

89

85

121

97

113

109

117

125

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†


RL = 10 kΩ

−75 5 25 45 65 85


RL = 600 Ω

RL = 2 kΩ

VCC ± = ±15 VVO = ±10 V

AV

D −

Lar

ge-

Sig

nal

Dif

fere

nti

alA

VD Vo

ltag

e A

mp

lific

atio

n −

dB

Figure 27




�




60

20

0

− 40

1 10 100 1 k 10 k 100 k

100

120

f − Frequency − Hz

SMALL-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE SHIFT

vsFREQUENCY

140

1 M 10 M 100 M

80

40

Gain

Phase Shift

− 20

140°

120°

100°

80°

60°

40°

20°

0°

Ph

ase

Sh

ift

180°

160°

VCC ± = ±15 V

AV

D −

Sm

all-

Sig

nal

Dif

fere

nti

alA

VD Vo

ltag

e A

mp

lific

atio

n −

dB

RL = 2 kΩCL = 100 pFTA = 25°C

Figure 28

− 10

− 20

30

1 4 10 40 100

f − Frequency − MHz

SMALL-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE SHIFT

vsFREQUENCY

20

10

0

CL = 25 pF

VCC ± = ± 15 V

Phase Shift

Gain

80°

120°

100°

140°

160°

180°

Ph

ase

Sh

ift

CL = 100 pF

AV

D −

Sm

all-

Sig

nal

Dif

fere

nti

alA

VD Vo

ltag

e A

mp

lific

atio

n −

dB

VIC = 0RL = 2 kΩTA = 25°C

CL = 100 pF

CL = 25 pF

Figure 29


�




Figure 30

10 100 1 k 10 k

CM

RR

− C

om

mo

n-M

od

e R

ejec

tio

n R

atio

− d

B


COMMON-MODE REJECTION RATIOvs

FREQUENCY

100 k 1 M 10 M

VCC ± = ±15 V

VCC ± = ±5 V

VIC = 0VO = 0RS = 50 ΩTA = 25°C

50

40

20

10

0

90

30

70

60

80

100

Figure 31TA − Free-Air Temperature − °C

85

82

76

73

70

97

79

−75 − 55 − 35 −15 5 25 45

CM

RR

− C

om

mo

n-M

od

e R

ejec

tio

n R

atio

− d

B

91

88

94

100

65 85 105 125

VIC = VICRmin

VCC ± = ±5 V

VCC ± = ±15 V

COMMON-MODE REJECTION RATIO†


VO = 0RS = 50 Ω

Figure 32

XX

XX

− S

up

ply

-Vo

ltag

e R

ejec

tio

n R

atio

− d

Bk

SV

R

SUPPLY-VOLTAGE REJECTION RATIOvs

FREQUENCY

40

20

0

− 2010 100 1 k 10 k 100 k

60

80


100

1 M 10 M

120

kSVR +

kSVR −

ΔVCC ± = ±5 V to ±15 VVIC = 0VO = 0RS = 50 ΩTA = 25°C


90

84

72

66

60

114

78

−75 − 55 − 35 −15 5 25 45

102

96

108

120

65 85 105 125

RS = 50 Ω

SUPPLY-VOLTAGE REJECTION RATIO†


kSVR +

kSVR −

XX

XX

− S

up

ply

-Vo

ltag

e R

ejec

tio

n R

atio

− d

Bk

SV

R VIC = 0VO = 0

ΔVCC ± = ±5 V to ±15 V




�




Figure 34|VCC ±| − Supply Voltage − V

ICC

− S

up

ply

Cu

rren

t −

mA

2

1.6

0.8

0.4

0

3.6

1.2

0 2 4 6 8 10 12

2.8

2.4

3.2

4

14 16 18 20

CC

I

TA = 25°C

TA = −55°C

TA = 125°C

VIC = 0VO = 0No Load

TLE2071SUPPLY CURRENT

vsSUPPLY VOLTAGE


ICC

− S

up

ply

Cu

rren

t −

mA

3

2.8

2.4

2.2

2

3.8

2.6

0 2.5 5 7.5 10 12.5 15

3.4

3.2

3.6

4

17.5 20 22.5 25

CC

I

TA = −55°C

TA = 25°C

TA = 125°C



vsSUPPLY VOLTAGE


ICC

− S

up

ply

Cu

rren

t −

mA

4

2

00 2 4 6 8 10 12

6

8

10

14 16 18 20

CC

I


TA = 25°CTA = −55°C

TA = 125°C


vsSUPPLY VOLTAGE


2

1.6

0.8

0.4

0

3.6

1.2

−75 − 55 − 35 −15 5 25 45

ICC

− S

up

ply

Cu

rren

t −

mA

2.8

2.4

3.2

4

65 85 105 125

CC

I


VCC ± = ±15 V

VCC ± = ±5 V

TLE2071SUPPLY CURRENT†




�





3

2.9

2.7

2.6

2.5

3.4

2.8

−75 −55 −35 −15 5 25 45

ICC

− S

up

ply

Cu

rren

t −

mA

3.2

3.1

3.3

3.5

65 85 105 125

CC

I


VCC ± = ±15 V

VCC ± = ±5 V




7

5

6

− 75 − 55 − 35 − 15 5 25 45

ICC

− S

up

ply

Cu

rren

t −

mA

8

9

10

65 85 105 125

CC

I


VCC ± = ±15 V

VCC ± = ±5 V



Figure 40VID − Differential Input Voltage − V

ICC

− S

up

ply

Cu

rren

t −

mA

− 0.5 − 0.25 0 0.25 0.50

6

8

10

12

I CC

VCC + = 5 VVCC − = 0VIC = 4.5 VTA = 25°COpen LoopNo Load

4

2


vsDIFFERENTIAL INPUT VOLTAGE


ICC

− S

up

ply

Cu

rren

t −

mA

− 0.5 − 0.25 0 0.25 0.50

6

8

10

12

14

I CC


4

2






�





ICC

− S

up

ply

Cu

rren

t −

mA

− 0.5 − 0.25 0 0.25 0.50

6

8

10

12

14

I CC

4

2


16

18

20




10

5

0−1.5 − 0.9 − 0.3 0 1.5

ICC

− S

up

ply

Cu

rren

t −

mA

15

20

25

I CC

13

8

3

18

23

0.3 0.9

VCC ± = ±15 VVIC = 0TA = 25°COpen LoopNo Load




10

5

0−1.5 −1 − 0.5 0 0.5 1 1.5

ICC

− S

up

ply

Cu

rren

t −

mA

15

20

25

I CC

VCC ± = ±15 VVIC = 0TA = 25°COpen LoopNo Load




8

4

0−1.5 − 0.3 0 0.9 1.2 1.5

ICC

− S

up

ply

Cu

rren

t −

mA

12

16

20

I CC

VCC ± = ±15 V

28

24

32

36

40

0.60.3− 0.6− 0.9−1.2

VIC = 0TA = 25°COpen LoopNo Load




�




Figure 46

IOS

− S

ho

rt-C

ircu

it O

utp

ut

Cu

rren

t −

mA

0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25

0

−12

− 36

− 48

− 60

48

− 24

24

12

36

SHORT-CIRCUIT OUTPUT CURRENTvs

SUPPLY VOLTAGE60

I OS

VO = 0TA = 25°C

VID = −1 V

VID = 1 V

|VCC ± | − Supply Voltage − V

Figure 47

IOS

− S

ho

rt-C

ircu

it O

utp

ut

Cu

rren

t −

mA

10

−10

− 20

− 500 60 120

30

40

t − Elapsed Time − s

50

180

20

0

I OS

SHORT-CIRCUIT OUTPUT CURRENTvs

ELAPSED TIME

VCC ± = ±15 V

VID = −1 V

VID = 1 V− 30

− 40

VO = 0TA = 25°C


IOS

− S

ho

rt-C

ircu

it O

utp

ut

Cu

rren

t −

mA

0

− 16

− 48

− 64

− 80

64

− 32

−75 − 55 − 35 −15 5 25 45

32

16

48

SHORT-CIRCUIT OUTPUT CURRENT†


80

65 85 105 125

OS

I

VCC ± = ±15 V

VCC ± = ±15 V

VCC ± = ±5 V

VCC ± = ±5 V

VID = −1 V

VID = 1 V

VO = 0


SR

− S

lew

Rat

e −

V/x

s

35

33

29

27

25

43

31

−75 − 55 − 35 −15 5 25 45

39

37

41

SLEW RATE†


45

65 85 105 125

sμ

V/ SR−

SR+

RL = 2 kΩCL = 100 pF

VCC ± = ±15 V




�





50

46

38

34

30

66

42

−75 − 55 − 35 −15 5 25 45

SR

− S

lew

Rat

e −

58

54

62

SLEW RATE†


70

65 85 105 125

sμ

V/

VCC ± = ±15 VRL = 2 kΩCL = 100 pF

SR−

SR+

Figure 51RL − Load Resistance − Ω

10

−10

0

− 20

− 50

50

− 30

100 1 k 10 k 100 k

30

20

40

SLEW RATEvs

LOAD RESISTANCE

VCC ± = ±15 VVO ± = ±10 V

Rising Edge

Falling Edge− 40

SR

− S

lew

Rat

e −

sμ

V/

VCC ± = ±5 VVO ± = ±2.5 V

AV = −1CL = 100 pFTA = 25°C


50

0.1 0.4 1 4 10

SLEW RATEvs


Rising Edge

Falling Edge

AV = −1

AV = 1

AV = 1

40

30

20

10

0

−10

− 20

− 30

− 40

− 50

SR

− S

lew

Rat

e −

sμ

V/

CL = 100 pFTA = 25°C

VO ± = ±10 V (10% − 90%)VCC ± = ±15 V

AV = −1

Figure 53

Vn

− E

qu

ival

ent

Inp

ut

No

ise

Volt

age

− 40

5

25

15

0

50

30

10 100 1 k 10 k

45

10

20


EQUIVALENT INPUT NOISE VOLTAGE(SPECTRAL DENSITY)

vsFREQUENCY

35

nV

nV

/H

z

VCC ± = ±15 VVIC = 0RS = 20 ΩTA = 25°C



�




Figure 54

0.011 10 100 1 k 10 k 100 k

Noise Bandwidth − Hz

1

0.1

10

100

INPUT-REFERRED NOISE VOLTAGEvs

NOISE BANDWIDTH

VCC ± = ±15 VVIC = 0RS = 20 ΩTA = 25°C

Peak-to-Peak

RMS

Vn

− In

pu

t-R

efer

red

No

ise

Volt

age

−V

nμ

V

Figure 55

0.3

0

− 0.3

− 0.60 1 2 3 4 5 6

Vn

− In

pu

t-R

efer

red

No

ise

Volt

age

−

0.6

0.9

t − Time − s

INPUT-REFERRED NOISE VOLTAGEOVER A 10-SECOND TIME INTERVAL

1.2

7 8 9 10

Vn

μV

VCC ± = ±15 Vf = 0.1 to 10 HzTA = 25°C

Figure 56

− 90

− 95

−100

−11510 15 20 25 30 35

Th

ird

-Oct

ave

Sp

ectr

ial N

ois

e D

ensi

ty −

dB

− 85

− 80

Frequency Bands

THIRD-OCTAVE SPECTRAL NOISE DENSITYvs

FREQUENCY BANDS− 75

40 45

VCC ± = ±15 V

Start Frequency: 12.5 HzStop Frequency: 20 kHz

−105

−110

VIC = 0TA = 25°C

Figure 57

0.00110 100 1 k 10 k 100 k

TH

D +

N −

To

tal H

arm

on

ic D

isto

rtio

n +

No

ise

− %

0.01


TOTAL HARMONIC DISTORTION PLUS NOISEvs

FREQUENCY

0.1

1

VCC ± = ±5 VVO(PP) = 5 VTA = 25°CFilter: 10-Hz to 500-kHz Band Pass

AV = 100, RL = 600 Ω

AV = 100, RL = 2 kΩ

AV = 10, RL = 2 kΩ

AV = 10, RL = 600 Ω



�




Figure 58

10 100 1 k 10 k 100 k


0.001TH

D +

N −

To

tal H

arm

on

ic D

isto

rtio

n +

No

ise

− %

TOTAL HARMONIC DISTORTION PLUS NOISEvs

FREQUENCY

0.01

0.1

1Filter: 10-Hz to 500-kHz Band Pass

AV = 10, RL = 2 kΩ

AV = 10, RL = 600 Ω

AV = 100, RL = 2 kΩ

AV = 100, RL = 600 Ω

VCC ± = ±15 VVO(PP) = 20 VTA = 25°C

Figure 59

B1

− U

nit

y-G

ain

Ban

dw

idth

− M

Hz

B1

10

9

8

70 20 40 60

11

12

UNITY-GAIN BANDWIDTHvs

LOAD CAPACITANCE13

80 100

VCC ± = ±15 V

CL − Load Capacitance − pF

VIC = 0VO = 0RL = 2 kΩTA = 25°C


10

9

8

7−75 − 55 − 35 −15 5 25 45

Gai

n-B

and

wid

th P

rod

uct

− M

Hz

11

12

GAIN-BANDWIDTH PRODUCT†


13

65 85 105 125

f = 100 kHzVIC = 0VO = 0RL = 2 kΩCL = 100 pF

VCC ± = ±15 V

VCC ± = ±5 V

Figure 61|VCC + | − Supply Voltage − V

10

9

8

70 5 10 15

Gai

n-B

and

wid

th P

rod

uct

− M

Hz

11

12

13

20 25

CC ±V

f = 100 kHzVIC = 0VO = 0RL = 2 kΩCL = 100 pFTA = 25°C

GAIN-BANDWIDTH PRODUCTvs

SUPPLY VOLTAGE



�




Figure 62

Gai

n M

arg

in −

dB

6

4

2

00 20 40 60

8

GAIN MARGINvs

LOAD CAPACITANCE10

80 100

VCC ± = ±15 VVIC = 0VO = 0RL = 2 kΩTA = 25°C


Figure 63

30°

20°

10°

0°

40°

50°

60°

70°

80°

90°

xm −

Ph

ase

Mar

gin

−75 − 55 − 35 −15 5 25 45

PHASE MARGIN†


65 85 105

mφ

VCC ± = ±15 V

VCC ± = ±15 V

VCC ± = ±5 V

VCC ± = ±5 V

125

VIC = 0VO = 0RL = 2 kΩ

CL = 25 pF

CL = 100 pF


Figure 64

PHASE MARGINvs

SUPPLY VOLTAGE

0 4 8 12 16 20

VIC = 0VO = 0RL = 2 kΩTA = 25°C

0°

10°

90°

80°

30°

20°

40°

50°

60°

70°

CL = 25 pF

CL = 100 pF

|VCC ±| − Supply Voltage − V

xm −

Ph

ase

Mar

gin

mφ

Figure 65

0°

10°

90°

80°

VIC = 0VO = 0RL = 2 kΩTA = 25°C

VCC ± = ±15 V

VCC ± = ±5 V

PHASE MARGINvs

LOAD CAPACITANCE

30°

20°

40°

50°

60°

70°

0 20 40 60 80 100


xm −

Ph

ase

Mar

gin

mφ




�




Figure 66

VO

− O

utp

ut

Volt

age

− V

0

− 5

− 10

− 150 1

5

10

NONINVERTING LARGE-SIGNALPULSE RESPONSE†

15

2 4 5

VO

VCC ± = ±15 VAV = 1RL = 2 kΩCL = 100 pF

TA = 25°C, 125°C

TA = 25°C, 125°C

TA = −55°C

3

TA = −55°C

t − Time − μs

Figure 67

0

− 50

−1000 0.4 0.8

VO

− O

utp

ut

Volt

age

− m

V 50

SMALL-SIGNAL PULSE RESPONSE100

1.2 1.6V

O

t − Time − μs

AV = −1RL = 2 kΩCL = 100 pFTA = 25°C

VCC ± = ±15 V

Figure 68

CLOSED-LOOP OUTPUT IMPEDANCEvs

FREQUENCY

0.00110 100 1 k 10 k 100 k 1 M 10 M


1

0.1

10

100

AV = 100

AV = 10

AV = 1

VCC ± = ±15 VTA = 25°C

0.01

zo −

Clo

sed

-Lo

op

Ou

tpu

t Im

ped

ance

− X

z oΩ

Figure 69

100

60

40

20

140

80

10 100 1 k 10 k 100 k

Cro

ssta

lk A

tten

uat

ion

− d

B

120


VCC ± = ±15 VVIC = 0RL = 2 kΩTA = 25°C

TLE2072 AND TLE2074CROSSTALK ATTENUATION

vsFREQUENCY



�



APPLICATION INFORMATION

input characteristics

The TLE207x, TLE207xA, and TLE207xB are specified with a minimum and a maximum input voltage that ifexceeded at either input could cause the device to malfunction. Because of the extremely high input impedanceand resulting low bias current requirements, the TLE207x, TLE207xA, and TLE207xB are well suited forlow-level signal processing; however, leakage currents on printed-circuit boards and sockets can easily exceedbias current requirements and cause degradation in system performance. It is good practice to include guardrings around inputs (see Figure 70). These guards should be driven from a low-impedance source at the samevoltage level as the common-mode input.

VI

R2R1

VI

R4

+

−

VO

R3

VI

+

−

VOVO

+

−

R3R4

�

R2R1

Where

Figure 70. Use of Guard Rings

TLE2071 input offset voltage nulling

The TLE2071 series offers external null pins that can be used to further reduce the input offset voltage. Thecircuit of Figure 71 can be connected as shown if the feature is desired. When external nulling is not needed,the null pins may be left unconnected.

+

−

VCC −

N2

N1100 kΩ

5 kΩ

IN−

IN+

OUT

Figure 71. Input Offset Voltage Nulling



�



APPLICATION INFORMATION

macromodel information

Macromodel information provided was derived using PSpice™ Parts™ model generation software. The Boylemacromodel (see Note 4) and subcircuit Figure 72 were generated using the TLE207x typical electrical andoperating characteristics at TA = 25°C. Using this information, output simulations of the following key parameterscan be generated to a tolerance of 20% (in most cases):

� Unity-gain frequency

� Common-mode rejection ratio

� Phase margin

� DC output resistance

� AC output resistance

� Short-circuit output current limit

� Maximum positive output voltage swing

� Maximum negative output voltage swing

� Slew rate

� Quiescent power dissipation

� Input bias current

� Open-loop voltage amplificationNOTE 4: G.R. Boyle, B.M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journal

of Solid-State Circuits, SC-9, 353 (1974).

OUT

+

−

+

−

+

−

+

−+

−

+

− +

−

+−

.SUBCKT TLE2074 1 2 3 4 5C1 11 12 2.2E−12C2 6 7 10.00E−12DC 5 53 DXDE 54 5 DXDLP 90 91 DXDLN 92 90 DXDP 4 3 DXEGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5FB 7 99 POLY (5) VB VC VE VLP VLN 0 + 5.607E6 −6E6 6E6 6E6 −6E6GA 6 0 11 12 333.0E−6GCM 0 6 10 99 7.43E−9ISS 3 10 DC 400.0E−6HLIM 90 0 VLIM 1KJ1 11 2 10 JXJ2 12 1 10 JX

RD1 4 11 3.003E3RD2 4 12 3.003E3R01 8 5 80R02 7 99 80RP 3 4 27.30E3RSS 10 99 500.0E3VB 9 0 DC 0VC 3 53 DC 2.20VE 54 4 DC 2.20VLIM 7 8 DC 0VLP 91 0 DC 45VLN 0 92 DC 45.MODEL DX D (IS=800.0E−18).MODEL JX PJF (IS=15.00E−12 BETA=554.5E−6+ VTO=−.6).ENDS

VCC +

RP

IN−2

IN+1

VCC −

RD1

11

J1 J2

10

RSS ISS

3

12

RD2

VE

54DE

DP

VC

DC

C1

53

R2

6

9

EGND

VB

FB

C2

GCM GA VLIM

8

5

RO1

RO2

HLIM

90

DLP

91

DLN92

VLNVLP

99

7

4

R2 6 9 100.0E3

Figure 72. Boyle Macromodel and Subcircut

PSpice and Parts are trademarks of MicroSim Corporation.


�



Revision History

Version Date Changes

C Dec−2009 – For TLE2071M/1AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17(f = 10 KHz), Pg. 16

– For TLE2071M/1AM (VCC ±15V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to12/17 (f = 10 KHz), Pg. 18

– For TLE2072M/2AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17(f = 10 KHz), Pg. 29


– For TLE2074M/4AM (VCC ±5V) changed Vn NOM & MAX from 28/55 to 48/85 (f = 10 Hz); 11.6/17 to 12/17(f = 10 KHz), Pg. 42


PACKAGE OPTION ADDENDUM

www.ti.com 8-Nov-2014

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

5962-9460201Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460201Q2ATLE2071MFKB

5962-9460201QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460201QHATLE2071M

5962-9460201QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460201QPATLE2071M


5962-9460202QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460202QHATLE2072M

5962-9460202QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460202QPATLE2072M


5962-9460203QCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460203QCATLE2074MJB

5962-9460203QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460203QDATLE2074MWB

5962-9460204Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629460204Q2ATLE2071AMFKB

5962-9460204QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460204QHATLE2071AM

5962-9460204QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460204QPATLE2071AM

5962-9460205Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460205Q2A

http://www.ti.com/product/TLE2071M?CMP=conv-poasamples#samplebuy









http://www.ti.com/product/TLE2071AM?CMP=conv-poasamples#samplebuy






Addendum-Page 2



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2072AMFKB

5962-9460205QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460205QHATLE2072AM

5962-9460205QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460205QPATLE2072AM

5962-9460206Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460206Q2ATLE2074AMFKB

5962-9460206QCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460206QCATLE2074AMJB

5962-9460206QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460206QDATLE2074AMWB

TLE2071ACD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2071AC

TLE2071ACDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2071ACDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2071ACP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2071AC

TLE2071ACPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2071AID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2071AI

TLE2071AIDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2071AIDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2071AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2071AIP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2071AI






http://www.ti.com/product/TLE2071A?CMP=conv-poasamples#samplebuy












Addendum-Page 3



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2071AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 59629460204Q2ATLE2071AMFKB

TLE2071AMJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2071AMJG

TLE2071AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460204QPATLE2071AM

TLE2071AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460204QHATLE2071AM

TLE2071CD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2071C

TLE2071CDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2071CDR OBSOLETE SOIC D 8 TBD Call TI Call TI

TLE2071CP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2071CP

TLE2071CPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2071ID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2071I

TLE2071IDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2071IDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2071IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2071IP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2071IP

TLE2071MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460201Q2ATLE2071MFKB

TLE2071MJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2071MJG

TLE2071MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460201QPATLE2071M





http://www.ti.com/product/TLE2071?CMP=conv-poasamples#samplebuy














Addendum-Page 4



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2071MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460201QHATLE2071M

TLE2072ACD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072ACDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072ACP ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072ACPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072AID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072AIDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072AIDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2072AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2072AIP ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072AIPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460205Q2ATLE2072AMFKB

TLE2072AMJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2072AMJG

TLE2072AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460205QPATLE2072AM

TLE2072AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460205QHATLE2072AM

TLE2072CD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072CDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)





















Addendum-Page 5



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2072CDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2072CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)


TLE2072CP ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072ID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072IDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)


TLE2072IDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 85 2072I

TLE2072IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 85 2072I

TLE2072IP ACTIVE PDIP P 8 50 Pb-Free(RoHS)


TLE2072IPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)



TLE2072MJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2072MJG

TLE2072MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9460202QPATLE2072M

TLE2072MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9460202QHATLE2072M

TLE2074ACDW ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074AC

TLE2074ACDWG4 ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074AC

TLE2074ACDWR OBSOLETE SOIC DW 16 TBD Call TI Call TI

TLE2074ACN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074ACN

TLE2074ACNE4 ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074ACN




















Addendum-Page 6



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2074AIDW ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074AI

TLE2074AIDWG4 ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074AI

TLE2074AIDWR OBSOLETE SOIC DW 16 TBD Call TI Call TI

TLE2074AIN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074AIN

TLE2074AINE4 ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074AIN

TLE2074AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9460206Q2ATLE2074AMFKB

TLE2074AMJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2074AMJ

TLE2074AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460206QCATLE2074AMJB

TLE2074AMWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460206QDATLE2074AMWB

TLE2074CDW ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074C

TLE2074CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)


TLE2074CDWR ACTIVE SOIC DW 16 2000 Green (RoHS& no Sb/Br)


TLE2074CDWRG4 ACTIVE SOIC DW 16 TBD Call TI Call TI

TLE2074CN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074CN

TLE2074CNE4 ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074CN

TLE2074IDW ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLE2074I

TLE2074IDWG4 ACTIVE SOIC DW 16 40 Green (RoHS& no Sb/Br)




















Addendum-Page 7



Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)


Samples

TLE2074IDWR ACTIVE SOIC DW 16 2000 Green (RoHS& no Sb/Br)


TLE2074IN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074IN

TLE2074INE4 ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLE2074IN


TLE2074MJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 TLE2074MJ

TLE2074MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460203QCATLE2074MJB

TLE2074MWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9460203QDATLE2074MWB

(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.








http://www.ti.com/productcontent



Addendum-Page 8

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF TLE2071, TLE2071A, TLE2071AM, TLE2071M, TLE2072, TLE2072A, TLE2072AM, TLE2072M, TLE2074, TLE2074A, TLE2074AM,TLE2074M :

• Catalog: TLE2071A, TLE2071, TLE2072A, TLE2072, TLE2074A, TLE2074

• Automotive: TLE2071-Q1, TLE2071A-Q1, TLE2071A-Q1, TLE2071-Q1, TLE2072A-Q1, TLE2072A-Q1

• Military: TLE2071M, TLE2071AM, TLE2072M, TLE2072AM, TLE2074M, TLE2074AM

NOTE: Qualified Version Definitions:

• Catalog - TI's standard catalog product

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

• Military - QML certified for Military and Defense Applications

http://focus.ti.com/docs/prod/folders/print/tle2071a.html

http://focus.ti.com/docs/prod/folders/print/tle2071.html





http://focus.ti.com/docs/prod/folders/print/tle2071-q1.html

http://focus.ti.com/docs/prod/folders/print/tle2071a-q1.html


http://focus.ti.com/docs/prod/folders/print/tle2071-q1.html



http://focus.ti.com/docs/prod/folders/print/tle2071m.html

http://focus.ti.com/docs/prod/folders/print/tle2071am.html





TAPE AND REEL INFORMATION

*All dimensions are nominal

Device PackageType

PackageDrawing

Pins SPQ ReelDiameter

(mm)

ReelWidth

W1 (mm)

A0(mm)

B0(mm)

K0(mm)

P1(mm)

W(mm)

Pin1Quadrant

TLE2071ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2071AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2071IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2072AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2072CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2072IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2072IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2072IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLE2074CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1

TLE2074IDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

TLE2071ACDR SOIC D 8 2500 340.5 338.1 20.6

TLE2071AIDR SOIC D 8 2500 340.5 338.1 20.6

TLE2071IDR SOIC D 8 2500 340.5 338.1 20.6

TLE2072AIDR SOIC D 8 2500 340.5 338.1 20.6

TLE2072CDR SOIC D 8 2500 340.5 338.1 20.6

TLE2072IDR SOIC D 8 2500 340.5 338.1 20.6

TLE2072IDR SOIC D 8 2500 367.0 367.0 35.0

TLE2072IDR SOIC D 8 2500 367.0 367.0 35.0

TLE2074CDWR SOIC DW 16 2000 367.0 367.0 38.0

TLE2074IDWR SOIC DW 16 2000 367.0 367.0 38.0

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2013

Pack Materials-Page 2

MECHANICAL DATA

MCER001A – JANUARY 1995 – REVISED JANUARY 1997

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE

0.310 (7,87)0.290 (7,37)

0.014 (0,36)0.008 (0,20)

Seating Plane

4040107/C 08/96

5

40.065 (1,65)0.045 (1,14)

8

1

0.020 (0,51) MIN

0.400 (10,16)0.355 (9,00)

0.015 (0,38)0.023 (0,58)

0.063 (1,60)0.015 (0,38)

0.200 (5,08) MAX

0.130 (3,30) MIN

0.245 (6,22)0.280 (7,11)

0.100 (2,54)

0°–15°

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. This package can be hermetically sealed with a ceramic lid using glass frit.D. Index point is provided on cap for terminal identification.E. Falls within MIL STD 1835 GDIP1-T8

IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.Products ApplicationsAudio www.ti.com/audio Automotive and Transportation www.ti.com/automotiveAmplifiers amplifier.ti.com Communications and Telecom www.ti.com/communicationsData Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computersDLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-appsDSP dsp.ti.com Energy and Lighting www.ti.com/energyClocks and Timers www.ti.com/clocks Industrial www.ti.com/industrialInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Security www.ti.com/securityPower Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defenseMicrocontrollers microcontroller.ti.com Video and Imaging www.ti.com/videoRFID www.ti-rfid.comOMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.comWireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2014, Texas Instruments Incorporated

http://www.ti.com/audio

http://www.ti.com/automotive

http://amplifier.ti.com

http://www.ti.com/communications

http://dataconverter.ti.com

http://www.ti.com/computers

http://www.dlp.com

http://www.ti.com/consumer-apps

http://dsp.ti.com

http://www.ti.com/energy

http://www.ti.com/clocks

http://www.ti.com/industrial

http://interface.ti.com

http://www.ti.com/medical

http://logic.ti.com

http://www.ti.com/security

http://power.ti.com

http://www.ti.com/space-avionics-defense

http://microcontroller.ti.com

http://www.ti.com/video

http://www.ti-rfid.com

http://www.ti.com/omap

http://e2e.ti.com

http://www.ti.com/wirelessconnectivity

Documents

TLE207x, TLE207xA EXCALIBUR LOW-NOISE HIGH … Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TLE207x, TLE207xA ... Q15 Q16 Q19 Q20