formerly Schaffner Test Systems

Company Profileand Product Overview

formerly Schaffner Test Systems

Teseq for EMC Test Solutions: A New Brand Combining Tradition

and Experience with Dynamic and Innovative Development

Teseq is the new name of the Test Systems Division that belonged to the

Swiss-based Schaffner Group until it became an independent company

in the wake of a management buyout on November 27, 2006.

Teseq has retained all of the former Division’s management and emplo-

yees, and their status as direct stakeholders in the company will ensure

intense commitment and a dynamic approach to development.

The new company also continues to stand for customized client sup-

port, proven products and extensive know-how. The Company’s focus

on its core business – EMC test solutions – will be reinforced by a

greater attention to innovation in the area of research and development.

The streamlined size of the enterprise ensures maximum independence,

agility and flexibility.

Around the world, Teseq stands for reliability – the Company’s manage-

ment and employees look forward to proving this every day.

03

Company Profile

04 Results for fast-paced industries

06 Better by design

08 At your side around the world

10 Cutting-edge technology

12 Convenience equals success

14 Service on demand

Product Overview

18 ESD simulators

19 Conducted EMC generators

20 Automotive conducted immunity test systems

22 Harmonics and flicker

23 RF conducted immunity test generator

24 RF power amplifiers

25 EMC antennas

26 EMI measuring receivers

26 Discontinuous interference analyzer with Windows software

27 GTEM/TEM cells

28 Additional products

32 EMC RF test software

34 Reverberation chambers

35 EMC consulting and system integration

36 Calibration and customer services

37 Customer support centers

38 Product standards and Teseq solutions

04

Time and creativity are the high-tech industry’s most precious resources.

05

Results for fast-paced industries

Teseq provides tools of progress.

Teseq delivers test equipment, test systems and end-to-end

solutions especially for fast-evolving technology sectors

that demand rapid, reliable results in compliance with cur-

rent standards. Nowhere is “survival of the fittest” manifested so

dramatically as in the fast-paced high-tech industry. This is precisely

where the benefit of Teseq’s test systems shines through: With

immediate and reliable results, every test is a step forward. Teseq

focuses on the following industries:

Automotive

Industrial electronics

Consumer electronics

Telecommunications

Medical

Aerospace/Defense

In these industries, we primarily serve the following clientele:

Independent test laboratories

In-house test laboratories

Development laboratories

Educational institutions

Rental companies

System integrators

Arlington, TX, 4pm

06

Better by designTeseq test systems for electronics manufacturers.

Teseq develops, produces, markets and implements test

systems for EMC emission and immunity. As pioneers in our

field, we have decades of market experience. Nowhere else will you

find a greater concentration of expertise. Our technologies, know-

how and representation in the influential bodies governing global

standards keep us one step ahead of our competition. Teseq’s test

systems are always cutting-edge and guaranteed to be standards

compliant. Our systems accelerate product development and pro-

duction, shortening your time to market.

Warsaw, 9am

07With the right tool, you can solve any problem.

08

At your side around the world

Teseq is where you are – worldwide.

Teseq stands for legendary Swiss quality and a personal

proximity to our customers worldwide. Through our branch

offices and network of highly qualified representatives, the world’s

most important regions are our home. Our employees speak the

language of their customers, come from the same culture and have

first-hand knowledge of local business conditions. They understand

the needs, the wants and the technical possibilities particular to

each region and are able to offer precisely the services that best

serve our customers in their own markets. The spectrum ranges

from specific and general consulting to knowledge sharing, system

implementation and the development of customized end-to-end

solutions.

Tokyo, 5pm

09We speak your language, wherever you are.

10

Trust is our standard.

11

Cutting-edgetechnology

Teseq equips you for the future.

Teseq is a leader in the application of cutting-edge techno-

logies. Our systems and solutions represent the state-of-the-art

when it comes to compatibility, connectivity, ease of use and

sustainable hardware and software.

Teseq offers an unparalleled scope. We deliver test systems

that meet all relevant standards. Our product suite is the broadest of

its kind anywhere in the world – and that’s not the only reason we

are unique. We also employ state-of-the-art technologies and offer a

modular test system architecture that allows you to build compre-

hensive, integrated and expandable test systems with lasting value.

Add our application software and you have customized solutions at

reasonable prices.

Product highlights

Touch screen for superior user-friendliness

Mobile PDA and Wi-Fi operation

Automated robotic test solutions

Customer-specific, configurable lab automation software

Windows XP based instruments

Modular system architecture

Perth, 8am

12

Convenienceequals success

Teseq optimizes your productivity.

Teseq guarantees robust software. We start with simplicity, reli-

ability and sustainable compatibility. We place special emphasis on a

user-friendly design that enables the use of convenience features to

enhance efficiency. This is true for both our standard software and

our customized, end-to-end system integration solutions. That’s why

Teseq test equipment has easy-to-use software interfaces.

We provide our customers with on-site experts who evaluate and

implement special software products. We offer training programs

that meet your enterprise’s specific training and education needs.

Our instructors are at home in the language and culture of our

customers.

Hamburg, 11am

13The future will render the virtual world real.

14

We take service personally.

15

Service on demandTeseq is a service provider.

Teseq offers a worldwide network of experts who provide

our customers with rapid response and effective communi-

cation. Our portfolio is not limited to a series of specific services.

We offer whatever service our customers need: from consultation,

service and training to the implementation of end-to-end solutions.

It goes without saying that we assist our customers with regular

hardware and software updates and keep them abreast of the latest

standards developments.

Teseq operates its own officially accredited calibration laboratories.

We offer calibration services around the globe, including all related

services, meeting the highest standards of quality.

London, 2pm

formerly Schaffner Test Systems

17

Product Overview

18 ESD simulators

19 Conducted EMC generators

20 Automotive conducted immunity test systems

22 Harmonics and flicker

23 RF conducted immunity test generator

24 RF power amplifiers

25 EMC antennas

26 EMI measuring receivers

26 Discontinuous interference analyzer with Windows software

27 GTEM/TEM cells

28 Additional products

32 EMC RF test software

34 Reverberation chambers

35 EMC consulting and system integration

36 Calibration and customer services

37 Customer support centers

38 Product standards and Teseq solutions

H- and E-field adapter, flexible discharge tips,

custom RC networks, calibration targets, etc.

Mains adapter, custom RC networks,

calibration targets, etc.

NSG 438

NSG 435

Voltage Display Polarity Accessories

30kV air/

contact max.

16.5kV air/9kV

contact max.

Easy to read

touch screen

Easy to read LCD

+/-, alternating

+/-, alternating

ESD simulatorscompact, user-friendly, and ready for tomorrow’s standards

The simulation of electrostatic discharges is an important part of EMC tests for

all types of electronic equipment. Many test standards require pulse voltages of

a few kV to 15kV while the automotive industry has even higher requirements. In

this case, voltages of up to 30kV must be applied to determine the immunity level.

Not only do Teseq’s ESD simulators meet all of today’s requirements, they are also

designed to comply with tomorrow’s standards.

Teseq’s ESD simulators are characterized by a compact and user-friendly design. The NSG 435

and NSG 438 both feature a large, easy to read LCD display that shows the user all necessary

parameters during tests. They can be operated either from rechargeable batteries or from a

mains power supply.

Air and contact discharge operation 200V to 30kV

Touch screen display

Battery-powered

Compliant with industry standards (IEC, ANSI, SAE, ISO, etc.)

Interchangeable network modules

Adjustable discharge detection

ISO self-test function

18

Magnetic field antenna, 3-phase

coupling network, variac, step transformers,

verification attenuators, etc.

Telecom wave, ring wave, damped oscillatory

pulses, 3-phase coupling network, variac,

verification attenuators, etc.

3-phase coupling network, 100A max.

constant current, verification attenuators, etc.

3-phase coupling network, verification

attenuators, etc.

Modula 6100

NSG 2050

NSG 2025

NSG 3025

Surge max.Burst/Fast transient max.

Power quality test (PQT) max. Accessories

4.4kV

6.6kV (8kV opt.)

–

–

4.8kV/1MHz

4.8kV/1MHz

8kV/500kHz

4.8kV/1MHz

Continuous: 16A

Short-term: 25A

Continuous: 16A

–

–

Conducted EMC generatorsinnovative user interface and software simplify test operations

Transient pulses superimposed on power and data cables, power interruptions, and

electromagnetic fields often cause malfunctions in electronic circuits and equip-

ment. Immunity testing can ensure that components, instruments, and systems

function properly during routine operation in conformance with product standards.

Teseq offers an extensive range of pulsed immunity generators as well as coupling

networks, antennas, variacs, and accessories to ensure that interference phenome-

na can be safely and reliably reproduced.

Teseq’s WIN Modula and EMC Suite test software simplify testing procedures and test file pro-

cessing, deliver flexible and adaptable test reports, and offer remote operation.

Comprehensive concept for immunity testing

Meet new IEC/EN standards

Innovative PDA operating concept

Open architecture

TCP/IP communication

Broad assortment of calibration accessories

Windows-based software

19

Capacitive discharge pulse

immunity generator

With its capacitive discharge circuits, the

NSG 5500 takes Teseq’s exclusive Gemini

technology a step further with unique pulse

generating functions, making it the only

solution that meets all ISO 7637-2:2004

immunity requirements.

Integrated battery switch/coupler

100A (250A peak)

Modular system based on Gemini

technology is easy to upgrade

Compliant with “capacitive discharge into

pulse shaping network”

JT 5510/JT 5550 JASO modules and NT

5510 NISSAN module

Automotive pulse 3a/b generator with two

pulse widths of 5/100ns and 5/150ns in

conformance with old and new standards

Generates pulses 1, 2 and supports prior

and current standards as well as pulses 6,

7 for backwards compatibility

The only pulse 5 generator that meets all

load-dump requirements

Battery voltage variation

and noise simulation generator

The NSG 5600, a combination function gene-

rator and power amplifier, makes it possible

to simulate vehicle voltage starting profiles,

voltage dips and drops, transformer-coupled

and other sinusoidal noise, and to conduct

magnetic field immunity tests.

Flexible, powerful, function generators are

simple to program

Modular and expandable up to 4 internal

synchronized function generators

Clone function for the digital recording

and duplication of oscilloscope

wave forms, or for importing from Math-

CAD, Excel, etc.

Direct programming of sine, square,

triangle, and exponential functions, DC

offsets and ramps

Unique functions for transformer-

coupled, sine-wave noise and

magnetic field immunity tests

NSG 5500

NSG 5600

Automotive conducted immunity test systemsmodular design is the key to success

Teseq is the first company to provide compact, modular, standards-compliant

systems, generators with automotive-specific functions, and power amplifiers for

battery simulation during EMC testing.

20

Battery simulator/Power amplifier

Based on years of experience with fast

power amplifiers for the automotive industry,

the PA 5840 has a unique capacitive stability

mode. Teseq test system users will now

enjoy the convenience of a wide range of

functions provided in one device: low impe-

dance, high currents, very high peak inrush

currents, high bandwidth, and stability in the

case of complex, variable loads in vehicle

electrical systems.

Developed specifically for automotive

tests, with capacitive stability mode and

additional unique functions

Output range -15V to +60V

Bandwidth up to 150kHz

Rise time < 10μs, i.e., no additional switch

required for voltage drops and dips for

most dropout applications

Three versions: 25A, 50A, and 100A conti-

nuous

Peak inrush current up to three times

continuous rating for up to 200ms

Rack mountable, modular, and

upgradeable

Immunity test software

AutoStar, Teseq’s leading software for auto-

motive immunity applications, features a test

management platform for controlling capaci-

tive discharge transient simulations, voltage

variations, and other immunity tests.

Optimized for automotive industry EMC

testing

More than 600 pre-programmed

standard tests for international and ma-

nufacturer-specific EMC standards

New tests can be programmed by the

user or downloaded from the Teseq web

site

PA 5840

AutoStar

21

System Power

[kVA]

Max. current outputLow voltage range [A]

High voltage range [A]

No. of output phases

IEC

610

00-3

-2

IEC

610

00-3

-3

IEC

610

00-3

-11

IEC

610

00-3

-12

IEC

610

00-4

-8

IEC

610

00-4

-11

IEC

610

00-4

-13

IEC

610

00-4

-14

IEC

610

00-4

-17

IEC

610

00-4

-27

IEC

610

00-4

-28

IEC

610

00-4

-29

PL 2101 1.25 8 4 1Ph

PL 2103 3 22 11 1Ph

PL 2105 5 37 18 1Ph

PL 2109 9 22 11 3Ph

PL 2115 15 37 18 3Ph

PL 2130 30 74 36 3Ph

PL 2145 45 100 50 3Ph

Harmonics and fl ickerTeseq as a pioneer for manufacturers and test centers

Teseq is a pioneer in the field of harmonics and flicker EMC testing. Manufac-

turers and test centers around the world trust Teseq ProfLine 2100 systems.

The ProfLine 2100 family’s modular design enables Teseq’s customers to configure

customized testing systems. These systems also offer cost-effective solutions for

a wide range of amperages from 1.25kVA to 45kVA per phase.

Real time PC-based power analyzer

1MS/s

Programmable AC/DC voltage source

Large power range 1.25kVA to 45kVA

Harmonic and interharmonic immunity testing in compliance

with IEC/EN 61000-4-13

Voltage drops and interruptions in compliance with IEC/EN 61000-4-11

and IEC/EN 61000-4-34 to 50A per phase

Windows software: WIN 2100 and WIN 2120 for simple testing

procedures, remote control, test file processing, and flexible test reports

22

RF conducted immunity test generator an advanced, compact RF immunity test system

The NSG 4070 is Teseq’s next-generation multifunctional immunity test system. It

replaces the NSG 2070 and offers expanded functionality plus new features. The

NSG 4070 has a broader frequency range of 9kHz to 1GHz and a modular design

which accommodates both internal and external amplifiers. The system can be

used in a wide variety of applications, including tests according to IEC/EN 61000-4-

6 and various BCI applications. The NSG 4070’s signal generator and power meter

can also be used to implement test systems for other applications such as IEC/EN

61000-4-3, IEC/EN 61000-4-20, and IEC/EN 61000-4-21.

Powerful and easy-to-use firmware allows the NSG 4070 to be operated independently. How-

ever, it can also be controlled by an external PC and control software. The USB port in the front

panel can be used with a standard USB memory stick to download test and measurement data

for documentation purposes.

Integrated signal generator 9kHz to 1GHz

4-channel power meter 9kHz to 1GHz

Integrated power amplifier for frequency ranges up to 1GHz and up to 75W

nominal output power

Multiple EUT monitoring options

Internal, menu-based control software

5.7” TFT color display

Optional remote control software

Additional products for conducted RF immunity tests

Teseq offers a wide assortment of coupling/decoupling networks and current injection clamps,

as well as an EM clamp for conducted RF immunity tests. All additional products are designed

to allow the highest possible injected signal levels at moderate input powers. Detailed informa-

tion about additional products can be found on page 26 ff.

23

Features Typical applications

Broadbandpower amplifiers

Power[W]

An

ten

na

mat

ched

, pro

file

d

freq

uen

cy r

esp

on

se

No

min

ally

fla

t fr

equ

ency

re

spo

nse

Sh

ort

- an

d o

pen

-cir

cuit

tole

ran

t

Cla

ss-A

Co

mm

erci

al E

MC

tes

tin

g

Au

tom

oti

ve

Mili

tary

Tele

com

CBA 9477B 15

CBA 9424/25/37 20/30/75

CBA 9423/42 100/200

CBA 9439 100

CBA 9450/35 300/1100

CBA 9426/13B/33 50/100/200

CBA 9434 400

CBA 9436 1000

CBA 9428/82 20/40

CBA 9429/38 75/120

CBA 9480 60

CBA 9481/83 800/250

CBA 9479 17

150kHz 1Ghz

150kHz 80MHz 230MHz 400MHz 800MHz

10kHz 100kHz 1MHz 10MHz 100MHz 1GHz 3GHz

150kHz 230Mhz

1MHz 400Mhz

80MHz 1Ghz

80MHz 1Ghz

800MHz 3Ghz

80MHz 1Ghz

800MHz 3Ghz

10kHz 100Mhz

10MHz 1Ghz

100kHz 1Ghz

10kHz 100Mhz

Frequency range

80MHz 1Ghz

RF power amplifi ershigh reliability at low operating costs

The CBA series is a complete range of solid-state class-A power amplifiers designed

with frequency and power ratings specifically for EMC immunity test applications.

These robust and dependable power amplifiers ensure complete reliability at low

operating costs. Teseq is constantly expanding the CBA series with models that

support new power and frequency ranges. Our specialists are ready to consult with

you regarding your application and custom requirements.

Solid-state class-A operation

Frequency range 10kHz to 3GHz

Reliable, designed and tested for EMC applications

Safe operation during open-circuit and short-circuit

Outputs suitable for EMC loads

24

BiLog®

X-wing BiLog

Biconical

antennas

Loop

antennas

CBL 6111

30MHz to 1GHz

CBL 6112

30MHz to 2GHz

CBL 6140

26MHz to 2GHz

CBL 6144

25MHz to 3GHz

Up to 600W

DPA 3000

800MHz to 2.8GHz

DPA 4000

200MHz to 1GHz

VBA 6106

30MHz to 300MHz

HLA 6120

9kHz to 30MHz

Compact

X-wing BiLog

Log periodic

antennas

DiPole

antennas

Broadband

horn antennas

CBL 6141

30MHz to 2GHz

CBL 6143

30MHz to 3GHz

UPA 6108

300MHz to 1GHz

UPA 6109

200MHz to 1GHz

VDA 6116

30MHz to 300MHz

UHA 9105

300MHz to 1GHz

BHA 9118

1GHz to 18GHz

BHA 9220

200MHz to 2GHz

EMC antennas achieve better results faster

Teseq has an extensive offering of EMC antennas. The

well-known BiLog® antenna, the first ultra wide band EMC

emission measurement antenna, represents an important

milestone in the development of EMC measuring instru-

ments. The BiLog® is a unique combination of a sophistica-

ted matching network and innovative design that provides

significant advantages over conventional EMC antennas.

As a result, measurements can be performed in one pass

without changing the antenna, resulting in a potential test

time savings of up to 30%. Subsequent measurements are

also easier to conduct and more reliable.

25

With its X-Wing® antennas, Teseq has applied the advancements of

the BiLog® antenna to immunity testing. The advantage of running

a complete immunity test with a single antenna provides significant

time savings. Teseq also offers loop antennas, biconical antennas

and broadband horn antennas.

Emission testing

Immunity testing

Wide frequency range

Individually calibrated

Optional accredited calibration

Frequency range 9kHz to 1GHz (SCR 3501)

Frequency range 9kHz to 2.75GHz (SCR 3502)

Compact and portable with built-in battery

Detectors (AV peak, QP)

IF bandwidth 200Hz, 9kHz, 120kHz

SCR 3501

SCR 3502

Frequency range 9kHz to 3GHz (SMR 4503)

Frequency range 9kHz to 18GHz (SMR 4518)

Detectors (AV peak, QP)

IF bandwidth 200Hz, 9kHz, 120kHz, 1MHz

SMR 4503

SMR 4518

Product Technical specifications

EMI measuring receivers compact, portable, multifunctional

All of Teseq’s EMI receivers can be used

in the laboratory to perform CISPR 16 ful-

ly compliant EMC testing and highly sen-

sitive, frequency selective voltage mea-

surements, calibrate other measuring

instruments, and perform attenuation

measurements to verify shielding effect.

They can also be used as components in

automated emission test systems.

26

The SMR series covers a broad frequency range of 9kHz up to 18GHz and provides a compre-

hensive user interface for performing even the most complicated measurements in a quick

and user-friendly manner. These receivers feature a large color display and provide extensive

setup information from the top-level menu. A special feature of the SMR 4503 is its upgrade-

ability to 18GHz.

The SCR series receivers are compact, portable and battery powered, which make them con-

venient to use in automotive and ungrounded test applications.

Even if they do not produce continuous interference, household products, power tools and

other appliances need to be measured for discontinuous interference in the range of 150kHz

to 30MHz. The DIA 1512D is comprised of a base unit and up to six plug-in fixed frequency

receivers, and all components are CISPR 16 compliant. With the DIA, all of the latest CISPR 14

tests can be conducted fully automatically – from determining click rate to analyzing click du-

ration and evaluating results in the form of a pass/fail test report. Since each channel operates

independently of the others, the analyzer may be used to perform simultaneous measure-

ments on different frequencies, dramatically reducing total test time.

CISPR 14 and CISPR 16 compliant

6 measuring channels

Self-calibration prior to every measurement

Modular system

Standard frequencies 150kHz, 500kHz, 1.4MHz, 30MHz

Windows-based ClickWare software (DIS 9966)

Discontinuous interference analyzer with Windows softwaremodular convenience

250mm

250mm

500mm

750mm

1000mm

1250mm

GTEM 250

GTEM 250 SAE

GTEM 500

GTEM 750

GTEM 1000

GTEM 1250

1500mm

1750mm

2000mm

GTEM 1500

GTEM 1750

GTEM 2000

300mmDTEM

150mm

150mm

800mm

SL 50

SL 90

SL 150

300mmTPL 3000

Product Septum height

DC to 20GHz

DC to 20GHz

DC to 400MHz

10kHz to 1GHz

10kHz to 1GHz

Frequency range

GTEM/TEM cellscustomizable, fast and effi cient

Teseq offers GTEM/TEM test cells for

EMC emission and immunity testing in

a shielded environment in accordance

with IEC/EN 61000-4-3 and IEC/EN

61000-4-20. Pre-certification tests can

be conducted during development in

compliance with IEC/EN 55022, VDE

0871, and other standards. Teseq’s

GTEM/TEM cells generate largely homo-

genous and simple to calculate fields

with an excellent VSWR over the entire

frequency range.

27

High field strengths at low amplifier output

No need to measure reflected power

Only simple single-channel power meters required

Reduced test time

Customized configurations

Frequency range DC to 20GHz

30MHz to 1GHz

1GHz to 18GHz

800MHz to 3GHz

30MHz to 3GHz

VSQ 1000

VSQ 2000

VSQ 3000

GVSQ 3002

30MHz to 1GHzKSQ 1000

150kHz to 2GHzCNE 6500B

1MHz to 1GHz

1GHz to 18GHz

1GHz to 6GHz

RSG 1000

RSG 2000

RSG 3000

Product Frequency range

Comparison radiation sources

Spherical radiation source

Comparison noise emitter

Reference voltage generators

Additional productsthe right choice for every need

Reference sources

In addition to EMC test systems meeting standards requirements, it is often necessary to com-

pare system performance of individual test setups and test sites. Teseq offers a wide range of

reference source products to meet these requirements.

Battery-powered

Ungrounded use

Reference calibrations available

28

RF switch networks

Teseq RF switch networks can be configured to switch RF signals in a wide range of automatic

test systems. Individual switches can connect one input to 2, 4, 6, or 8 outputs. Multiple swit-

ches can be configured in a mainframe, making the number of switch configurations virtually

unlimited. All RF switch networks are characterized by high quality and an operating life of at

least one million switch cycles.

Frequency range up to 18GHz

Simple control via IEEE488 interface

Listener and talker functionality

Actual switch positions are readable

Mainframe can hold up to 12 switch units

Virtually unlimited switch configurations

RFB/RFC 2000

Coupling/decoupling networks (CDN) in

compliance with IEC/EN 61000-4-6

IEC/EN 61000-4-6 specifies the design and per-

formance of a wide range of coupling and

decoupling networks (CDNs). Each CDN is

specific to a particular type of cable and signal.

Teseq offers an extensive range of CDNs

which fully comply with the requirements

of the standard and provide a simple and

reliable method of injecting RF energy into

the equipment under test. CDNs can also be

used for emission testing. Special types fulfill

CISPR/F/399/CDV (CISPR 15) requirements to

300MHz.

IEC/EN 61000-4-6 compliant

Frequency range 150kHz to 230MHz

Wide range of special models and

connector types

CDN types: M, S, T, AF, ST, USB and CAN

EUT AC voltages up to 250V

RF voltages to 30V max.

Calibration adapters available

Impedance stabilization networks (ISN)

compliant with CISPR 22 Ed. 5.0

Impedance stabilization networks (ISNs) are

used for emission measurement on tele-

communication lines. Teseq offers a wide

range of ISNs for CISPR 22 Ed. 5.0. Adapter

sets are available for shielded or unshielded

cables with connector types BNC, RJ11 or

RJ45. T-type ISNs for unshielded, balanced

wire pairs are supplied with LCL adapters for

cable categories 3 and 5.

Frequency range 150kHz to 230MHz

Emission measurements on balanced wire

pairs

CISPR 22 Ed. 5.0/EN 55022:2003

compliant

Support all common connector types

Models support 1 to 8 lines

CDN

ISN

29

Decoupling and absorbing clamps

Decoupling clamps are available for a variety of different EMC applications.

They can provide additional isolation of the test signal from the auxiliary

equipment during immunity testing. For emission testing, they are used as

terminations on all cables coming from the equipment under test, thus creating

a more repeatable test setup.

Max. operating current 25A

3 models 150kHz to 1GHz

Absorbing clamps are used for measuring interference signals on power supply cables of

household appliances according to CISPR 14, and are CISPR 16 compliant. They can be used

in manual as well as automated measuring fixtures.

Frequency range 30MHz to 1000MHz

Current sensing probe

RF current sensing probe CSP 9160 for measurements according to CISPR 22

or BCI with a transfer impedance of 1 . The CSP 9160 is the probe of choice for conducted

emission measurements.

Frequency range 10kHz to 100MHz

Emission testing

CISPR 16 compliant

CMAD 10

CMAD 20

KEMA 801

AMZ 41

CSP 9160

CVP 2200

NNB 41/NNB 42 Line impedance stabilization networks (LISN)

In emission tests, EUT cables must be terminated with a defined RF impedance. Line impe-

dance stabilization networks (LISNs) provide the defined impedance

so that the interference voltage of the equipment under test can be measured in

a reproducible manner.

Frequency range 9kHz to 30MHz

V-network

EUT voltage up to 240V single phase, 450V 3-phase

EUT current up to 16A single phase, 32A 3-phase

EUT supply frequency up to 63Hz

Capacitive voltage probe

Capacitive voltage probe CVP 2200 according to CISPR 22. Active probe with

switchable gain.

Frequency range 100kHz to 30MHz

Emission testing

CISPR 16 compliant

Additional products30

Near field probe set

The near field probe set is a diagnostic tool

kit for detecting electrical and magnetic

interference fields. The set includes three

hand-held probes (two magnetic fields and

one electric field) for a frequency range of

9kHz to 1GHz, 30dB pre-amplifier, power

supply, and a test fixture. When used in

conjunction with a spectrum analyzer or

measuring receiver, the probes can locate

and evaluate electromagnetic interference

sources.

Frequency range 9kHz to 1GHz

Emission testing

Development tool

Pre-amplifier

The pre-amplifier model series is invalu-

able for the measurement of low signal

strengths. These pre-amplifiers offer a

wide bandwidth, high gain, and a low noise

figure. They are essential for radiated field

strength measurements using spectrum

analyzers, together with low sensitivity/

small gain broadband antennas.

Frequency range 9kHz to 3GHz

Emission testing

N-connectors

RF accessories

Teseq offers an extensive range of acces-

sories for various EMC applications.

The RF power meters, tripods, antenna

adapters, pulse limiters, etc. that are used

in EMC systems are not included herein.

Wide array of RF accessories,

including DCP 0100, CHA 9652,

ATN series, CFL 9206

NFPS1

CFL 9206

RFP 4001*

RFP 4002*

CPA 9231CPA 9232

* special design for Teseq receivers

31

The user can configure the program for any type of test (commercial, automotive, military,

telecommunications, etc.) and set up customized and optimized testing processes. The Emis-

sion Assistant feature allows the user to clone existing standard tests, modify them, and then

save or run the result through an interactive check box system.

Fully featured, infinitely flexible

Applicable to all market segments

User can create new instrument drivers

Complex hardware configurations using multiple receivers/spectrum analyzers

Unlimited mechanical handling devices (antenna masts, turn tables, etc.)

Choice of test report generating tools provides fast configurable reports

Compliance 3 Emission

Extremely complex hardware configurations with multiple frequency-specific test segments

can be displayed and checked prior to conducting testing. Special monitoring functions en-

sure the reliability and functionality of the test equipment as well as the EUT, thus maximizing

test efficiency.

Supports virtually any hardware

Hardware configuration and test setup displayed in simple graphical format

Administrator controls all user access

Locked down test, factor files, etc. ensure consistency

Access to raw data and factor file information on a frequency point basis allows

checking of data manipulation

Supports most languages

Help desk support and comprehensive web site

Compliance 3 Immunity

EMC RF test softwarefaster automated results

Compliance 3

Windows-based Compliance 3 is a new and creative approach to the operation of

RF emission and immunity test systems for EMC applications. Compliance 3’s open

architecture allows users to select from Teseq’s comprehensive suite of pre-pro-

grammed standards-compliant test methods, or to design their own custom test

methods. Compliance 3’s most unique feature is the flexibility of its EUT monitoring

capability, which allows the user to more completely automate the test process.

Teseq also offers application specific versions of Compliance 3: Emipak 3 for low

cost, pre-compliance emission testing and GTEM 3 for emission and immunity

testing in GTEM cells.

32

Based on the Compliance 3 package, Emipak 3 is configured for low cost, pre-compliance

emission testing. The program includes pre-defined test procedures as well as an Assistant

feature that leads the user through the process of creating a new test.

Easy to operate user interface

Pre-configured

Pre-compliance RF conducted and radiated emission testing

Results presented simply and clearly

Can be upgraded to Compliance 3 Emission

Emipak 3

These versions of Compliance 3 are optimized for conducting immunity or emission testing in

a GTEM cell. The Immunity package features pre-defined hardware configurations and a four

step menu to lead the user through defining and running a test. With the Emission package

and an EUT manipulator, the EUT can be automatically positioned into each of the orthogonal

X, Y and Z planes. The program records the three files and simulates final data on an open

area test site (OATS).

Easy to operate user interface

Pre-configured

Supports conducted and radiated testing

Results presented simply and clearly

Can be upgraded to full Compliance 3 versions

GTEM 3 Emission and Immunity

33

Model S

Model M

Model L

Model range Technical specifications

Model S, M, or L screened room

Mode tuner with stepping motor

Control software

Shield test of the screened room

Custom room sizes

Shielded control room

Antennas and tripods from Teseq

Calibration and performance tests

per various standards

Turnkey systems

Standard configuration Options

2.5 x 4 x 2.55m, LUF 200MHz,

max. EUT volume 1m3

3.1 x 7 x 2.55m, LUF 100MHz,

max. EUT volume 4m3

12.5 x 5.5 x 4m, LUF 80MHz,

max. EUT volume 30m3

Other sizes and upgrades of existing screened rooms to a reverberation chamber on request.

Reverberation chamberspowerful software delivers automatic effi ciency

Reverberation chambers (RCs) are modern EMC test environments in addition to

the established methods like semi- or full anechoic rooms, open area test sites or

(G)TEM cells. They can be used for emission and immunity testing.

Wide frequency range 100MHz to > 18GHz

Excellent field homogeneity (< 3dB)

Full and pre-compliance testing

Radiated emission and immunity measurements

Stirrer optimized by numerical analysis

Continuous or stepped rotation

Calibrated per IEC/EN 61000-4-21 and various other standards

Powerful control software for automated system operation

Consulting, calibration and services

34

Supported standards

IEC/EN 61000-4-21

RTCA DO 160 D/E

MIL461E

GMW3097

ES-XW7T-1A278-AC

Others on request

One of the most important points during establishment, calibration, and final use of a rever-

beration chamber is the calibration, control and evaluation software. Using Teseq’s powerful

system software (C++ based) Compliance 3, these procedures are solved comfortable and

time effective, e.g.:

Individual equipment configuration for the reverberation chamber system

Complex EUT test sequences can be defined on worksheets

Different test segments can be created, any details are stored in an input window

Results are displayed simultaneously in graphical and tabular form

Powerful test report generator and measurement data export options

Powerful control software

Consultation and quotationSystem design and

implementaionInstallation, maintenance

and support

EMC consulting and system integrationreliability in every phase

Meeting today‘s EMC compliance requirements is an extensive and complex task.

There are numerous standards and requirements depending upon product, ap-

plication and territory. Most manufacturers and test laboratories do not have the

resource to define a complex EMC test system to meet their needs. This leads to

considerable risk when selecting and constructing an EMC test laboratory.

Teseq offers a complete solution for EMC test facilities and guarantees full service over the

entire product life – from site surveys and hardware/software configuration to start-up, final

acceptance, training and calibration. Its extensive knowledge of EMC systems can be seen

around the world with hundreds of systems installed in application fields such as automotive,

telecommunications, commercial, military and medical.

Complete integration of Teseq and third party EMC equipment

Global experience, purchasing, logistics, consultancy and support

Expertise in automotive, medical, military and telecommunications

applications and many more

Hundreds of systems installed worldwide

Dedicated EMC specialists to evaluate current and future requirements

35

Calibration and customer servicesworldwide, fast and cost-effective

For fast-turnaround calibration and repair of all your commonly used EMC test

equipment, choose Teseq’s calibration and customer services. The most extensive,

single-source service for the calibration of RF and conducted EMI test equipment in

the world, Teseq provides test laboratories with fast, reliable, high quality service.

Teseq’s extensive worldwide EMC calibration and repair capability is built on our own high

quality standards and longstanding engineering experience. We operate own laboratories,

most of them accredited to national and international standards, and offer both accredited and

traceable calibration services. All have full test and repair facilities for our EMC equipment. We

test and calibrate other manufacturers’ equipment as well.

Teseq guarantees 10 years of calibration and repair service from the date of purchase and

minimal downtime for the customer. Our experts are also available for customer-specific

consulting and training.

Teseq also offers the following services around the globe:

On-site calibration*

Repair

Training

Consulting

Equipment rental*

Television antenna benchmarking*

* Not available at all sites

Accreditation gives confidence in the competence of a calibration laboratory.

Accreditation provides confidence in certificates and reports by implementing widely accepted

criteria set by the European (CEN) or international (ISO) standardization bodies. The standards

address issues such as impartiality, competence and reliability; leading to confidence in the

compatibility of certificates and reports across national borders.

36

Switzerland Germany UK USA Singapore China Japan

SA

S a

ccre

dit

atio

nEN

ISO

/IEC

170

25

Trac

eab

le

DK

D a

ccre

dit

atio

nEN

ISO

/IEC

170

25

Trac

eab

le

UK

AS

acc

red

itat

ion

EN IS

O/I

EC 1

7025

Trac

eab

le

A2L

A a

ccre

dit

atio

nEN

ISO

/IEC

170

25

Trac

eab

le

Trac

eab

le

Trac

eab

le

Trac

eab

le

ESD pulses, e.g. IEC 61000-4-2 to 30kV

Burst pulses, e.g. IEC 61000-4-4 to 8kV

Surge pulses, e.g. I EC 61000-4-5 to 10kV

Mains drop-outs and dips, e.g. IEC 61000-4-11

Mains drop-outs and dips, DC, IEC 61000-4-29

Automotive pulse generators

Power amplifiers

Electric field strength 10kHz to 1000MHz,1 to 30V/m

Field strength probes DC to 6GHz

EMI measuring receivers

TEM wave guides (e.g. GTEM cells), IEC 61000-4-20

Chambers

Coupling and decoupling networks(LISNs, ISNs, CDNs, clamps)

Current clamps

Directional couplers

RF probes, RF pre-amplifiers and attenuators

RF site calibration

Antennas

LVD testers

Harmonics and flicker

On-site conducted EMC calibration

Customer support centerssupporting you worldwide

The accredited calibration service is designed for accredited test laboratories. It is based

on calibration equipment, procedures, measurement uncertainties and personnel which have

all been assessed by a national accreditation authority to ensure accuracy of measurement.

The traceable calibration service is ideal for all types of commercial and in-house test la-

boratories. It uses similar traceable measurement equipment, and almost the same processes.

Both accredited and traceable calibration services are in line with the recommendations of

EN ISO/IEC 17025. The capabilities of each Teseq support center are listed below.

37

Commercial & Industrial

EN 61000-6-1 IEC 61000-6-1 Generic immunity standard Residential, commercial and light industrial environment

EN 61000-6-2 IEC 61000-6-2 Generic immunity standard Industrial environment

EN 61000-6-3 IEC 61000-6-3 Generic emission standard Residential, commercial and light industrial environment

EN 61000-6-4 IEC 61000-6-4 Generic emission standard Industrial environment

EN 61000-3-2 IEC 61000-3-2 Basic emission standard Harmonic currents

EN 61000-3-3 IEC 61000-3-3 Basic emission standard Voltage fluctuations and flicker

EN 61000-3-11 IEC 61000-3-11 Basic emission standard Voltage fluctuations and flicker

EN 61000-3-12 IEC 61000-3-12 Basic emission standard Harmonic currents

EN 61000-4-2 IEC 61000-4-2 Basic immunity standard Electrostatic discharge

EN 61000-4-3 IEC 61000-4-3 Basic immunity standard Radiated RF field

EN 61000-4-4 IEC 61000-4-4 Basic immunity standard Electrical fast burst transients

EN 61000-4-5 IEC 61000-4-5 Basic immunity standard Surge

EN 61000-4-6 IEC 61000-4-6 Basic immunity standard Conducted RF

EN 61000-4-8 IEC 61000-4-8 Basic immunity standard Power frequency magnetic field

EN 61000-4-9 IEC 61000-4-9 Basic immunity standard Pulse magnetic field

EN 61000-4-11 IEC 61000-4-11 Basic immunity standard AC voltage dips, interruptions and variations < 16A per phase

EN 61000-4-12 IEC 61000-4-12 Basic immunity standard Ring waves and oscillatory waves

EN 61000-4-13 IEC 61000-4-13 Basic immunity standard Harmonics and interharmonics

EN 61000-4-14 IEC 61000-4-14 Basic immunity standard Voltage fluctuations

EN 61000-4-20 IEC 61000-4-20 Basic immunity and emission standard Transverse electromagnetic (TEM) waveguides

EN 61000-4-21 IEC 61000-4-21 Basic immunity and emission standard Reverberation chamber test methods

EN 61000-4-27 IEC 61000-4-27 Basic immunity standard Voltage unbalance

EN 61000-4-28 IEC 61000-4-28 Basic immunity standard Variation of power frequency

EN 61000-4-29 IEC 61000-4-29 Basic immunity standard DC voltage dips, interruptions and variations

EN 61000-4-34 IEC 61000-4-34 Basic immunity standard AC voltage dips, interruptions and variations > 16A per phase

EN 55011 CISPR 11 Product family emission standard Industrial scientific and medical (ISM) radio frequency equipment

EN 55013 CISPR 13 Product family emission standard Broadcast receivers and associated equipment

EN 55014-1 CISPR 14-1 Product family emission standard Household appliances, electric tools and similar

EN 55014-2 CISPR 14-2 Product family immunity standard Household appliances, electric tools and similar

EN 55015 CISPR 15 Product family emission standard General lighting equipment

EN 55020 CISPR 20 Product family immunity standard Broadcast receivers and associated equipment

EN 55022 CISPR 22 Product family emission standard Information technology equipment

EN 55024 CISPR 24 Product family immunity standard Information technology equipment

ANSI IEEE C62.41 Recommended practice in low voltage AC power circuits

Scope Area of use

Automotive

EN 55025 CISPR 25 Vehicle and component RF emission tests

ISO 11451 Vehicle RF immunity tests

ISO 11452 Component RF immunity tests

SAE J1113 Component emission and immunity tests

ISO 7637 Component conducted emission and immunity tests

ISO 10605 Electrostatic voltage immunity in road vehicles

ISO 16750-2 Stress testing of electronic systems and components

2004/104/EC EC type-approval – "e" marking for components

Telecommunications

Bellcore EMC and electrical safety – generic criteria for network telecom equipment

FCC Connection of terminal equipment to the telephone network

ETSI EMC for telecom equipment

ITU – K series Immunity of telecom equipment

Product standards and Teseq solutionsselection of the most commonly used standards

38

EN 61000-6-1 IEC 61000-6-1

EN 61000-6-2 IEC 61000-6-2

EN 61000-6-3 IEC 61000-6-3

EN 61000-6-4 IEC 61000-6-4

EN 61000-3-2 IEC 61000-3-2

EN 61000-3-3 IEC 61000-3-3

EN 61000-3-11 IEC 61000-3-11

EN 61000-3-12 IEC 61000-3-12

EN 61000-4-2 IEC 61000-4-2

EN 61000-4-3 IEC 61000-4-3

EN 61000-4-4 IEC 61000-4-4

EN 61000-4-5 IEC 61000-4-5

EN 61000-4-6 IEC 61000-4-6

EN 61000-4-8 IEC 61000-4-8

EN 61000-4-9 IEC 61000-4-9

EN 61000-4-11 IEC 61000-4-11

EN 61000-4-12 IEC 61000-4-12

EN 61000-4-13 IEC 61000-4-13

EN 61000-4-14 IEC 61000-4-14

EN 61000-4-20 IEC 61000-4-20

EN 61000-4-21 IEC 61000-4-21

EN 61000-4-27 IEC 61000-4-27

EN 61000-4-28 IEC 61000-4-28

EN 61000-4-29 IEC 61000-4-29

EN 61000-4-34 IEC 61000-4-34

EN 55011 CISPR 11

EN 55013 CISPR 13

EN 55014-1 CISPR 14-1

EN 55014-2 CISPR 14-2

EN 55015 CISPR 15

EN 55020 CISPR 20

EN 55022 CISPR 22

EN 55024 CISPR 24

ANSI IEEE C62.41

ESD

gen

erat

ors

Co

nd

uct

ed E

MC

ge

ner

ato

rs

Au

tom

oti

ve c

on

du

cted

im

mu

nit

y te

st s

yste

ms

Har

mo

nic

s an

d f

licke

r

RF

con

du

cted

imm

un

ity

test

gen

erat

or

RF

po

wer

am

plif

iers

EMC

mea

suri

ng

ante

nn

as

EMI m

easu

rin

g re

ceiv

ers

Dis

con

tin

uo

us

inte

rfer

ence

an

alyz

er

GTE

M/T

EM c

ells

Rev

erb

erat

ion

cham

ber

s

EMC

RF

test

so

ftw

are

EN 55025 CISPR 25

ISO 11451

ISO 11452

SAE J1113

ISO 7637

ISO 10605

ISO 16750-2

2004/104/EC

Bellcore

FCC

ETSI

ITU – K series

Commercial & Industrial

39

To find your local partner within Teseq’s global network, please go to www.teseq.com

691-001B Mar 2007

© 2007 TeseqSpecifications subject to change without notice. All trademarks recognized.

HeadquartersTeseq AG4542 Luterbach, SwitzerlandT +41 32 681 40 40F +41 32 681 40 48sales@teseq.comwww.teseq.com

Why buy from Teseq?Decades of market experience

Industry experts active in establishing global standards

Best-of-breed products

Modular architecture

Excellent price-to-performance ratio

User-friendly software solutions

Widest range of local services around the globe

Shared language and culture with our customers

ChinaTeseq Limited CompanyT +86 10 6510 1772F +86 10 6510 1236chinasales@teseq.com(as of Apr 2007)

FranceTeseq SarlT +33 1 39 47 42 21F +33 1 39 47 40 92francesales@teseq.com

GermanyTeseq GmbHT +49 30 5659 8835F +49 30 5659 8834desales@teseq.com

JapanTeseq K.K.T +81 3 5456 8929F +81 3 5456 8930japansales@teseq.com

SingaporeTeseq Pte Ltd.T +65 6846 2488F +65 6841 4282singaporesales@teseq.com

SwitzerlandTeseq AGT +41 32 681 40 50F +41 32 681 40 48sales@teseq.com

UKTeseq Ltd.T +44 845 074 0660F +44 845 074 0656uksales@teseq.com

USATeseq Inc.T +1 732 417 0501F +1 732 417 0511Toll free +1 888 417 0501usasales@teseq.com

Teseq is an ISO-registered company. Its products are designed and manu-factured under the strict quality andenvironmental requirements of the ISO 9001.

This document has been carefully checked. However, Teseq does not assume any liability for errors or inaccuracies.