TEQIP-II Agenda

BHAGALPUR COLLEGE OF ENGINEERING, BHAGALPUR.

TEQIP-II

Agenda for discussion and approval

1. To get approval for the appointment of consultant for NBA Accreditation in Civil, Electrical and Mechanical Engineering.

At least 60% of ourUGprogrammes should be accredited. Accreditation are awarded based on the sufficient Infrastructures, Student Faculty

Ratio, Faculties Qualifications, and others College Activities. Accreditation1 is a formal, third party recognition of competence of our

Colleges.In NBA, the Course will be accredited based on courses. The Department of Science and Technology is very keen to move for

accreditation of Civil, Electrical and Mechanical Engineering course. The accreditation fees for 3 Course will be Rs 9.00 lakhs.

Accreditation is essential to promote quality conscious where excellence, relevance to market needs and participation by all stake holders are

prime and major determinants. It is important to set the quality benchmarks targeted at global and national level. We have to make evaluation

and self-assessment of our programmes mentioned above. Therefore, it is urgent need to appoint consultant for preparing the self-appraisal

reports of our Institution based on guidelines, norms and standards specified by NBA.

2. To seek approval of revised procurement plan for the different departments

Enhancing the laboratories towards the successful transformation into the Centre of excellence. Establishing the research culture in the institute

for collaborative working of various departments. Effectively executing the procurement policy in tune with the Guidelines of World Bank and

associated government bodies for more transparent and fair procedure for which approval from SPFU and NPIU is also necessary.

S.No.

Activities Total

Allocation

Permissible Expenditure

Infrastructure improvements for teaching, training and learning through

1The vision of the NBA is “to be an accrediting agency of international repute by ensuring the highest degree of credibility in assurance of quality and relevance of professional education and come to the expectations of its stakeholders, viz., academicians, corporate, educational institutions, government, industry, regulators, students, and their parents

1. Establishment of new laboratories and strengthening of existing for PG programs, faculty research, etc.Procurement of furniture.Details are in Annexure 1.

480 Lakh

a) New equipment and furniture: establishing new PG laboratories and strengthening of

existing laboratories Faculty research and institutional consultancy work Campus‐Wi Fi networking of academic and

administrative buildings, hostels and faculty Residences.

Course‐specific Software (Rs. 50.00 L).

Modernization and Strengthening of Libraries (Rs. 50.00 L):

Procurement of print and digitized books, e‐journals Expenditure for digitization of library books Establishment of CD bank Membership of INDEST - AICTE consortium (The

Ministry of Human Resource Development has set-up the Indian National Digital Library in Engineering Sciences and Technology (INDEST) Consortium.The consortium headquarters set-up at the IIT Delhi. Besides, 44 Government or Government-aided engineering colleges and technical departments in universities have joined the Consortium with financial support from the AICTE. Moreover, the INDEST Consortium, as an open-ended proposition, welcomes other institutions to join it on their own for sharing benefits it offers in terms of highly discounted rates of subscription and better terms of agreement with the publishers. The Consortium has an active mailing list and a Web site hosted at the IIT Delhi).

Civil Worksrefurbishment of existing structures/ spaces to create new laboratories for PG programs and research as per the need ( Rs 5.00 Lakh)

2 Updating of learning resources

3 Modernization and strengthening of libraries and increasing access to knowledge resourcesDetail in

Annexure 24

Refurbishment (Minor Civil Works)

5 Providing Teaching and Research Assistantships for significantly increasing enrolment in existing and new Masters and Doctoral programs in Engineering disciplines

100.0 L

TEQIP Scholarships (Rs. 25.00 L): Teaching and Research Assistance ships for Master’s students in engineering disciplines who are not getting any other Scholarships or those who are not sponsored by any company.

Developing research interest among UG students Fiscal incentive to students that voluntarily associate

with industry oriented R&D projects and Travel cost of students that associate with an industry for about 3‐4 weeks during vacations to continue work on R&D projects.

Registration Fees for UG students attending National Conferences for presenting Research Paper or Attending a STTP useful for Research.

Inviting expert Lecturers from Research Institutes to contents other than Syllabus related to research topics.

6 Enhancement of R.& D. and institutional consultancy activities

20.00 L

1. Enhancement of R.& D. and Consultancy securing sponsored projects and consultancy

assignments Publication of research papers in per reviewed

journals commercialization of research products

patenting of research products Travel cost, hospitality and honorarium

paid to Consultant for participation inR & D and for delivering Expert lectures

2.Organizing National and InternationalConferences (Bihar and all the States in the Indo-Gangetic plane have very nice ravine sediments deposited along the banks of Ganga and other rivers. These are very good material for brick making. There are so many brick kilns along the banks of rivers. The construction of houses with this technology would reduce the cost by about 35 %. The

houses built in such a fashion with a seismic belt would be seismically stable, climatically suitable and environment friendly. It is purposed to arrange a national seminar on Key Hole Brick Technology within next two / three months at Patna through a one day conference or Seminar. The cost would be approximately Rs 5.00 Lakh.

Hospitality to participants Venue and logistic arrangements Replication of printed training materials Publication of proceedings Travel, boarding & lodging for

invited experts3. Seed Money for Research Projects

Seed money for good innovative projectsfor equipment and consumables

7 Faculty and Staff development for improved competence based on TNA Annexure 3

100 L

Faculty Qualification Up gradation1. Fees charged for course work and use of research facilities; and consumables by the institution where faculty is enrolled for qualification up gradation either through fulltime or part‐time or by sandwich scheme.2. Consumables, if faculty is registered for qualification up-gradation on full‐time or part‐time basis within the parent Institution

b) Subject knowledge and research competence up-gradation of Facultyas planned through TNA• Course fee; travel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when faculty is deputed out‐station to another institution (within India or abroad) for the duration of the course, travel time and the time permitted by the BoG (for travel abroad) and by Principal (for National Travel) for visits to institutions/organizations of interest and relevance to the

faculty• Course fee and local travel expenses as per applicable norms and rules when faculty attends a course in‐station but at an institution other than the parent institution

c) Resource sharing through collaborative arrangements• Travel expenses; boarding, lodging, and sundry expenses/allowances for faculty visiting institutions and industries within India to develop and implement joint projects with well-defined deliverables.• Hospitality, local travel, for Faculties visiting from other institutes to BCE Bhagalpur for guidance and collaboration

d) Organizing subject area Continuing Education Training Programs,Workshops2, seminars3 as per norms decided by the BoG.• Hospitality to participants• Venue and logistic arrangements• Replication of printed training materials• Publication of proceedings• Travel, boarding & lodging for invited experts• Honorarium for delivering lectures and training in BCE BhagalpurTraining of Technical Support Staff• Course fee; travel expenses; boarding, lodging, and sundry expenses 4as per applicable norms and rules when the technical support staff is deputed outstation to another organization within India and travel time• Course fee and local travel expenses as per applicable norms and rules when training is attended in‐station but at an

2 A four days workshop organised on composite course on earthquake which covers the following aspects: Scientific aspects of earthquake, Engineering aspects of earthquake, Disaster management aspect of earthquake, and Tsunami. Further, a two week course has been organised by NITTR Kolkatta on Pedagogy.

3 Bihar and all the States in the Indo-Gangetic plane have very nice ravine sediments deposited along the banks of Ganga and other rivers. These are very good material for brick making. There are so many brick kilns along the banks of rivers. The construction of houses with this technology would reduce the cost by about 35 %. The houses built in such a fashion with a seismic belt would be seismically stable, climatically suitable and environment friendly. It is purposed to arrange a national seminar on Key Hole Brick Technology within next two / three months at Patna through a one day conference or Seminar.4 Expenditure incurred in attending International Seminar on the 6th Conference of the International Society for Integrated Disaster Risk Management (IDRIM -TIFAC 2015) held in Delhi during October 28-30, 2015 is Rs 25,000/-. It was attended by Principal, Dr Nirmal Kumar.

institution other than the parent institution

Group Training Arranged for Faculty/Staff Fees for participants, transport, food, etc. for the training programs arranged by the Institute in collaboration with Industry or some outsourced partyReimbursement of travel cost for the faculty5, who attend International and National Conference in India and Abroad.

8 Enhanced interaction with industry

Rs 40 L

Increasing Industry-Institute-Interaction• Travel cost, hospitality and honorarium paid to industry personnel for participation in curriculum development/revision/restructure, student assessment and institutional bodies, and for delivering expert lectures• Expenditure for increasing Institute Industry Interaction

Placement Activities for Students• Expenditure towards inviting industries (excluding travel cost and lodging boarding) for campus interviews and hospitality during campus interviews• Arranging tutoring by industry experts to prepare students for on‐ and off‐campus job interviews

9 Institutional management capacity enhancement

Rs 30.00 Lakh

Training of Institution Officials and Senior Faculty and Orientation of BoG Members6

1. Course fee; travel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when deputed outstation to another institution (within India or abroad) for the duration of the course, travel time and the time permitted by the BoG (for travel abroad)/ by Principal for National Travel for visits to institutions/ organizations of

5 Expenditure incurred in attending Training Course by Dr Nagendra Choudhary may be approved amounting to Rs 20000.00 ( Twenty thousand) only.6 Expenditure incurred on visit of Prof Jaiprakash , Mentor from 25-27th October 2015 may be approved amounting to Rs 50000.00 ( Fifty thousand) only.

interest and relevance to the faculty in the vicinity of the location of training2. Trainer’s fee and overheads; and sundry expenditure if training programs organized within the parent institution.3. Travel costs, boarding and lodging expenditure and sitting fee to Board members; sundry expenses on organizing Orientation program.Study ToursTravel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when deputed for study tour within India or abroad for the duration of the tour and travel time.

10 Implementation of Institutional reforms

Rs 20 L

Curricular ReformsTravel cost, hospitality and honorarium paid to industry personnel for participation in curriculum development/revision/restructure & reforms; Sundry expenditure on holding meetings of the concerned committees.

Accreditation: Accreditation fee to NBA

11 Academic support for weak students( Annexure 3)

Rs 40.00 Support to Academically Weak Students Psychological Services and Support for Needy

Students for coping with the institutional environment.

Support for Students to Improve their Employability

Honorarium to faculty and staff for taking bridge courses,

remedial teaching classes and skill development training and

TA, DA to outside experts for specialized training in soft

components including communication‐ presentation skills

12 Incremental Operating Cost

Rs 100.00 Lakh BoG and other Committee Meetings

TA & DA for faculty and staff attending workshops, Meetings and training in the World Bank procedures as organized/arranged by the NPIU and SPFUs

Occasional hiring of vehicles for project related work only

Salaries of additional full‐time regular and contract faculty and staff appointed against posts created under the Project

In‐house maintenance of existing and new equipment

Maintenance of equipment including computers and related devices and assets provided under the Project through Annual Maintenance Contracts

Office operation including stationery, postage, electronic communication, telephone, electricity, water, etc.

consultancy Services engaged for technical assistance related to procurement of Civil Works and equipment, pedagogical training, mentoring, hand‐holding for Project implementation as required by weak institutions, external financial auditing

Contract fee for outsourced services Procurement related expenses I,e.; Advertisement,

related stationary, photography, video shooting, and hospitality charges.

13 Total Rs 930 Lakh

Annexure 1(A)

laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % Engineering Mechanics Lab. ladk; % ;kaf=dh vfHk;a=.k

Øe

lapkfyrikB;Øe ds vuqlkjiz;ksx”kkyk ,oadeZ”kkykesavko”;d e”[email protected]

laLFkku ds iz;ksx”kkyk ,oadeZ”kkykeasiwoZslsmiyC/k e”[email protected]

Ø; gsrqizLrkfore”[email protected] vH;qfDrUkke la[;

kfof”kf’V

;k¡izfr ;wfuVnj¼:

0 esa½dqyvuqekfureqY; ¼:0

esa½1 Reaction at Support

Apparatus Reaction at support Apparatus

1. Compound pendulum

01 10,000 10,000

2 Moment of inertia of flywheel

Moment of Inertia of flywheel

2. Stop watch 1/10 second

05 2,500 12,500

3 Moment of inertia of Ring Moment of inertia of Ring 3. Wooden meter scale

12 100 1,200

4 Screw jack Screw jack 4. Weight box up to 100 gm

02 500 1,000

5 Compound pendulum 5. Slide callipers 02 500 1,000

6 Belt friction Belt friction

7 Stiffness of spring Stiffness of spring

8 Stop watch 1/10 second(05 Pieces.)

9 Wooden meter scale (12 Pieces.)

10 Weight box up to 100 gm

–(2 Pieces.)

11 Slide callipers (2 Pieces.)

Total (Rs) 25,700

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % Mk;usfeDlvkWQe”khujhladk; % ;kaf=dh vfHk;a=.k

Øe



Ø; gsrqizLrkfore”[email protected] vH;qfDrUkke la[;

kfof”kf’V;k¡

izfr ;wfuVnj ¼:0 esa½

dqyvuqekfureqY; ¼:0 esa½

1 Gyroscope Gyroscope 1. Whirling of

shaft

01 75,000 75,000

2 Balancing machine Balancing machine 2. Cam Analysis

machine

01 1,00,000 1,00,000

3 Connecting rod Connecting rod 3. Universal

vibrations

Apparatus

01 1,00,000 1,00,000

4 Whirling of shaft 4. Digital

Techometer

01 12,000 12,000

5 Cam Analysis Machine

6 Universal vibrations Apparatus

7 Digital Techometer

Total (Rs)- 2,87,000

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % fgV ,.M eklVªkalZQjladk; % ;kaf=dh vfHk;a=.k

Øe



Ø; gsrqizLrkfore”[email protected] vH;qfDrUkke la[;k fof”kf’

V;k¡izfr ;wfuVnj

dqyvuqekfureqY;

¼:0 esa½1 Heat transfer through composite

wall01- Not working 1. Heat transfer through

composite wall apparatus

01 1,00,000

2 Transient heat Conduction apparatus

Nil 2. Transient heat Conduction

01 50,000

3 Measurement of surface emissivity apparatus

01- Not working 3. Measurement of surface emissivity apparatus

01 50,000

4 Stefan Boltzman’s apparatus 01- Not working 4. Stefan Boltzman’s apparatus

01 50,000

5 Heat transfer through natural Convection

01 – working 5. Heat exchanger (parallel & counter flow)

50,000

6 Heat transfer through forced convection

01 -working 6. Condensation apparatus (Film wise & drop wise)

50,000

7 Heat transfer through plate fin 01 -working

8 Heat exchanger (Parallel & Counter flow )

Nil

9 Condensation apparatus (Film 01 - Not working

wise & drop wise)

Total (Rs). 3,50,000

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % vkbZ0 lh0 batu ,oaxSlVjckbuiz;ksx”kkykladk; % ;kaf=dh vfHk;a=.k

Øe




V;k¡izfr ;wfuVnj¼:0 esa½

dqyvuqekfureqY; ¼:0 esa½

1 2 Stroke Petrol Engine Test Rig 2 Stroke Petrol Engine Test Rig – Not working

1. Maruti Engine 4 stroke 4 cylinder water cooling

01 50,000 50,000

2 4 Stroke Diesel Engine Test Rig 4 stroke Diesel Engine Test Rig- Not Working

2. Two stroke model for petrol Engine

01 20,000 20,000

3 4 Stroke Petrol Engine Test Rig 3. Four stroke model for petrol Engine

01 20,000 20,000

4 Digital Techometer 4. Four stroke model for Diesel Engine

01 20,000 20,000

5 Stop watch 5.Digital Techometer

02 12,000 24,000

6 Battery 12V, 25 Plate – 2 Nos. 6. Stop watch 05 2,500 12,500

7. Battery 12V, 25 Plate – 2 Nos.

02 20,000 40,000

Total (Rs)- 1,86,500

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % Workshop

ladk; % ;kaf=dh vfHk;a=.k Øe




V;k¡izfr ;wfuVnj

dqyvuqekfureqY;

¼:0 esa½1 Lathe machine Lathe machine

Working-02, Not working- 10

1. Milling machine 01 2,50,000 2,50,000

2 Grinding machine Grinding machineWorking-01, Not working-01

2. Spot welding machine

01 1,50,000 1,50,000

3 Drilling machine Drilling machineWorking-01, Not working-02

3. Cuppola furnace 01 1,00,000 1,00,000

4 Vertical shaper machine Vertical shaper machineWorking-01, Not working-03

4. CNC Lathe.

Technical Specification:

DNC Based PC-Controlled horizontal bed lathe. Machine complete with fully enclosed working area, safety units according to CE- regulations steeples adjustable main drive, 8- station tool turret, manual tailstock

01 9,00,000 9,00,000

automatic movement to the reference position electrical and mechanical preparation for automation connection cable PC machine, disk with machine data Must be programmable through control keyboard designed as per industrial control & control software like: Operation : Control Keyboard same as industrial control units Preparation for the exchange to other control systems.Control Systems

1. SIEMENS & GE FANUC

2. CAD/CAM

Working area should not be less than dimensions given below.

1. Swing over bed (mm) ∅ 125

2. Swing over cross slide (mm) ∅ 55

3. Max machining diameter (Chuck parts with tailstock) (mm) ∅50

4. Max. Parts length (mm) 215

Travel

1. Travel in X- axis

(mm) 452. Travel in Z- axis

(mm) 225

Main Spindle

1. Spindle nose according factory standard

2. Spindle bone (mm) ∅ 15

3. Chuck diameter (mm) 70

4. Hole to chuck (mm) ∅ 15

5. Speed range (rpm) 120-4000

6. Mechanical spindle speed 2

7. Max. torque (Nm) 14

Main drive

1. AC – motor,2. Speed range

(rmp) 1200 to 14000

Tool turret (Important)

1. Number of tool stations -8

2. Tool holding inside/outside -4/4

Feed drives

1. 3 phase step motor

2. Rapid traverse in X/Z

Tailstock

1. Quill stroke (mm) 35

2. Quill diameter (mm) 22

3. Internal taper MT 1

DNC- interface

1. For remote control via a software protocol. The communication in done via the Rs. 232 interface for the FMS/CIM – operation

Safety equipment

Machine full covered axis limit switch door limit switch emergency according CE standard

Documentation

1. Machine description

2. Software Manual3. Electrical

documentation4. Training manuals5. Teaching material

5 Forge heating Equipment Forge heating EquipmentWorking-01, Not working-09

5. CNC Milling MachineTechnical

1 12,50,000 12,50,000

Specification

DNC based PC – controlled 4-axis milling machine for universal CNC training with 8- station tool turret machine complete with fully enclosed working area, step less adjustable main drive automatic movement tc the reference

Must be programmable through control keyboard & software like,

Operation : Control Keyboard same as industrial control units, preparation for the exchange to the control systems:

Control System

1. Siemens & GE Fanuc

2. CAD/ CAM

Technical data of the machine (not less than)

Working area,

1. Longitudinal travel (X-axis) (mm) 175

2. Cross travel (Y-axis) (mm) 125

3. Vertical travel (Z-axis) (mm) 250

Milling table

1. Clamping surface (L x W) (mm) 400x 120

2. 2 T- slots

Tool system

1. Tool magazine pick-up system with swivel arm on the left of the milling head placed. Blow out facility.

2. System drive electr, mech.

3. Tool clamping automatic

4. Number of tool station 8

Main drive

1. Asynchronous AC motor,

2. Speed range (Step less) (U/min) 150

Feed drive

1. 3 phase step motor in x/y/z axis

2. Feed rate and rapid traverse in x/y/z

4th axis (c -axis)

1. Continuously controlled

2. Spindle height

40mm3. Displacement

20mm4. Retrofit able

DNC- Interface

1. For remote control via a software protocol. The communication is done via the Rs. 232 interface for the FMS/CIM – operation

Safety equipment

1. Machine full covered, axis limit switch door limit switch emergency off switch

2. According CE standard

Documentation

1. Machine description

2. Software manual3. Electrical

documentation4. Training manuals5. Teaching material

6 Milling machine Milling machine- Not working

6. Electric welding machine (Memco)

1 1,20,000 1,20,000

7 Spot welding machine Spot welding machine-Not working

7. Welding Helmet 10 500 5,000

8 Cuppola furnace Cuppola furnace-Not working

8. Hand Screen 10 400 4,000

9 CNC Lathe CNC Lathe- Not working 9. Black Glass 20 200 4,000

10 CNC Milling Machine 10. White Glass 40 100 4,000

11 Electric welding machine (Memco)

11. Cable Clamp 10 100 1,000

12 Welding Helmet 12. Welding holder 08 500 4,000

13 Hand Screen 13. Earth Clamp 02 500 1,000

14 Black Glass 14. Chipping Hammer

10 200 2,000

15 White Glass 15. Wire Brush 20 100 2,000

16 Cable Clamp 16. Gas Welding Trolly

01 10,000 10,000

17 Welding Holder 17. Gas Cylinder (Oxygen) with regulator

01 18,000 18,000

18 Earth Clamp 18. D. A. Cylinder with regulator

01 12,000 12,000

19 Chipping Hammer 19. Cutting torch 01 5,000 5,000

20 Wire Brush 20. Welding torch (bati)

01 3,000 3,000

21 Gas Welding Trolly 21. Flame Nipple (any size)

05 1,000 5,000

22 Gas Cylinder (Oxygen) with 22. Welding goggles 10 100 1,000

regulator

23 D. A. Cylinder with regulator 23. Apron (Leather) 10 600 6,000

24 Cutting torch 24. Filler wire M.S. 5Pkd 1000 /pkd

6,000

25 Welding torch (Balti) 25. Flux 5Pkd 100/Pkd 500

26 Flame Nipple (any size) 26. Electrode 4 Bandle 5,000/ Bandle

20,000

27 Welding goggles 27. Welding cable 20 metre

250 /metre

5,000

28 Apron (Leather) 28. Hand Gloves 20set 300/set 6,000

29 Filler wire M.S. 29. M. S. Plate (4mm)

4mm 8,000

30 Flux 30. M. S. Plate (8mm)

8mm 10,000

32 Electrode

33 Welding cable

34 Hand Gloves

Total (Rs.) 29,12,500

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % CAD/CAM Lab. (List of Furnitures)

ladk; % ;kaf=dh vfHk;a=.k

Øe




V;k¡izfr ;wfuVnj

dqyvuqekfureqY;

¼:0 esa½1 Computer table 40 1. Computer Table 10 5000 50,000

2 Ceiling fan Nil 2. Ceiling fan 10 2500 25,000

3 Padestal fan Nil 3. Padestal fan 02 3000 6,000

4 Executive table Nil 4. Executive table 01 30,000 30,000

5 Executive chair (Godrej) Nil 5. Executive chair (Godrej)

06 5,000 30,000

6 Godrej table Nil 6. Godrej table 15 2,000 30,000

7 Rack Nil 7. Rack 01 25,000 25,000

8 Stool (plastic) Nil 8. Stool (plastic) 10 500 5,000

Total (Rs) 2,01,000

ii=laLFkkudkuke % ch0 lh0 bZ0] Hkkxyiqjiz;ksx”kkykdkuke % Workshop (List of Furnitures)

ladk; % ;kaf=dh vfHk;a=.k

Øe




V;k¡izfr ;wfuVnj

dqyvuqekfureqY;

¼:0 esa½1 Ceiling Fan 1. Ceiling Fan 15 2,500 37,500

Total (Rs) 37,500

SCIENCE AND TECHNOLOGY DEPARTMENT, PATNA BIHAR

SL NO NAME OF LABORATORY AMOUNT (Rs.)

1 ENGG. MECHANICS LAB 25,700

2 DYNAMICS OF MACHINERY 2,87,000

3 HEAT AND MASS TRANSFER 3,50,000

4 I.C. E. ENGINE AND GAS TURBINE 1,86,500

5 WORKSHOP 29,12,500

6 CAD/CAM LAB (LIST OF FURNITURES) 2,01,000

7 WORK SHOP (LIST OF FURNITURES) 37,500

TOTAL (Rs). 40,00,200

TEQIP –IIMECHANICAL ENGINEERING DEPARTMENT

Steam power Laboratory Sl. Name of Equipment’s Rate/unit in Rs. (Approx) Qty. Amount in Rs. (Approx)1 Miniature steam power plant equipped with

Boiler, turbine, condenser & other measuring equipment (to perform experiment in laboratory) output- Mechanical & Electrical (Both) System capacity – 5kw Boiler- Diesel Oil fired

10,00,000 01 10,00,000

Total (Rs). 10,00,000


CAD/CAM LAB.

Sl. Name of Equipment’s Qty. Technical specification Rate/unit in Rs. (Approx)

Amount in Rs. (Approx)

1 Cabin (control + in charge) size - (16’ x 14’x 18’) Made –Board & sales

Store cum subordinate staff Room (14’x 8’x 8’)

0116’ x 14’x 18’

14’x 8’x 8’

300/sqft 1,20,000

2Flooring (2200sqft.) 2200 sqft. 100sqft.

2,20,000

3. AC (split) with stabilizer 03 1.5ton 40,000 1,20,000

4 Projector with accessions 01 1,00,000 1,00,000

5 Desktop for server 01 8GB RAM i3 processor, Intel Mother board Intel Mother 1TB

Hard Disk

50,000 50,000

6 Auto cad 2015 (latest) 05 2TB HDD 40,000 2,00,000

7 Catia V5 (latest) 05 1,05,000 5,25,000

8 Ansys (latest) with ansys work bench 05 28,000 14,00,000

9 Antivirus Norton, McAfee 51 Norton 360 2015 12000 61,200

Total (Rs.) 27,96,200


REFRIGERATION LAB.

Sl. Name of Equipment’s Qty. Rate/unit in Rs. (Approx)

Amount in Rs. (Approx)

1 Vapour Compression Unit Mechanical Heat Pump Test Rig

01 70,000 70,000

2 Vapour Compression Unit Test Rig-Cycle of Refrigeration

01 70,000 70,000

3. Domestic Refrigeration R- 43 01 30,000 30,000

4 Air Conditioning – Test Rig 01 70,000 70,000

5 Ice Plant Test Rig 01 70,000 70,000

Total (Rs.) 3,10,000

TEQIP –II

SL NO NAME OF LABORATORY AMOUNT (Rs.)

1 STEAM POWER LABORATORY 10,00,000

2 CAD/CAM LAB. 27,96,200

3 REFRIGERATION LAB 3,10,000

TOTAL (Rs). 41,06,200

B. Civil Engineering DepartmentList of Machines/ Equipment’s

S. No Name of equipment’s Specification Qty. Rate Amountincluding VAT

Total Amount (Rs.)

Concrete Lab.1 Compression testing

MachineAnalogue Compression Testing Machine, Capacity 2000kN,Electrically Operated, Single Gauge confirm IS – 14858 (2000), ASTM – C-39, AASTHO –T-22 with NCCBM certified load gauge. Loading Unit: Electrically operated fully welded of steel cross head and machined steel base with solid support plates. The hydraulic jack of 2000kN capacity is fixed on the base. The upper platen has got a self-aligning action. The lower platen rests on the jack ram and is positioned centrally with the help of a centering pin. Loading is accomplished by the upward movement of the lower platen. Both the lower and the upper platens are hardened, ground and polished. Guidelines are marked on the lower platen to keep the specimen centrally and co-axially with the hydraulic jack. A dust cover is provided on the jack to prevent any dust going into the cylinder of the jack. Four spacers with locating pins are provided to be inserted in between the lower platen and the hydraulic jack to reduce the excessive gap between the two

1 3,50,000.00

platens when small specimens along with brick platen are required to be tested. Motorized Pumping Unit :Motorized pumping unit of 2000kN is housed in an elegant cabinet and is of two speed design driven by an electric motor. A connector is fixed to connect the motor to the mains through ON-OFF Push Button Switch. Slow and fast lever which is fitted with a knob. To and fro movement of this lever, coarse adjustment of rate of loading can be done. Fine adjustment can be done by rotating the knob fitted on this lever. Release valve preferred to be provided on the top of the pump. Pressure can be released by unscrewing the knob. Oil reservoir is fitted with oil filler plug cum dipstick , drain plug , and safety valve The unit is suitable for operation on 220volts, 1 phase, 50 cycles AC supply.3General Specification:Least Count : 10 Kn.Accuracy: +- 1%Platen max clearance: 370 mm.Upper swiveling arrangement. Side plate distance ( Max) : 340 mm Size of platen: 222.0 mm dia. Platen hardness: 60 BHN Piston dia : 222.2 mm. Piston stroke : 50 mm.Specimen sizes : 70.6mm,100mm, 150mm Cube and cylinder.Frame stiffness : 3000 KN / mm.Weight :1500 KG aprox.Painting: Powder coating with a minimum thickness of 75 micron.Pump noise level : within 65 dbSample viewing port: 305 x 460 mm with poly acrylic transparent sheet.NABL Calibration with traceability Certificate

2 Flexure Testing Machine 100kN Flexure Testing Machine Electrically Operated, are designed to test flexural strength of concrete beams. The design provide maximum rigidity throughout their working range. The load is applied by the downward movement of the piston. A spacer is provided for testing different size of beams. The load is indicated on a calibrated bourdon tube type load gauge of range : 0 -100 kN x 0.5 kN,The load gauge is calibrated against National Physical Laboratory / National Council for Cement and Building Materials certified proving ring. Light weight, rugged high strength frame • Double action hydraulic pump • Self-aligning roller assembly • Hydraulic jack provided with retraction spring,• For testing beams of 100X100X500mm and 150X150X 700mm. Suitable for operation on 220V, 50Hz, Single Phase, AC supply (For Electrically Operated Flexure Testing Machine).Least count-0.5KN,center distance between supporting roller for various beam size,600mm and 400mm. center distance between loading roller for various beam size-200mm and 133mm.

1,50,000.00

3 Concrete Permeability Apparatus,

Concrete Permeability Apparatus, 3 Cell model for 150mm cube as per IS 3085 with Compressor 15kg/sq cm capacity

1,34,000.00

4 Air Entrainment Apparatus,

Air Entrainment Meter Capacity 0.005m3 (5 litres) suitable for aggregate size upto 38mm, consists of a pressure-tight flanged cylindrical measuring bowl, fitted with a removeable flanged and a conical cover assembly with a seal in-between. The conical cover hasan air valve and a pet cock for bleeding-off the water. A cylindrical stand pipe, which is graduated in per cent air content, is fixed on the conical cover assembly. Required pressure is applied to the specimen with the help of a pressure bulb. The whole assembly is mounted on a flat base. Each apparatus is supplied complete with a calibrating cylinder, pressure gauge, funnel, trowel and tamping bar.

23,000.00

5 Fatigue Testing Machine Maximum bending moment kg.cm 200 bending moment adjustable kg.cm 25-200 ranges kg. cm 5-125 gripping dia of specimen 12mm, testing dia of specimen 8mm rotating speed 4200rmp, accuracy of applied bending moment +- 1% digital counter 8 digit, power required Hp 0.5, main supply 3ph, 415V, 50Hz, AC, overall size (approx) 1000L x 5000W x 600H weight (approx) 120kg.

1,80,000.00

6 Tile Abrasion Testing Machine

Tile Abrasion Testing Machine for tile sample is pressed under a specified load against a grinding path, strewen evenly with an abrasive powder, revolving at the rate of 30 ± 1 rpm. At the end of 100 revolutions of the disc, the second parallel side of the tile is subjected to wear an equal number of revolutions of

the disc. The wear of the tile is measured using AIM48101 thickness measuring device (which is supplied at extra cost). The Abrasion Testing Machine consists of a replaceable

1,39,350.00

grinding path, fitted on to a disc rotating

about its vertical axis. The rotating disc and the grinding path are enclosed by a circular tray. A bracket holds the specimen. The loading is by a counterbalanced lever. Afunnel is provided to facilitate charging the grinding path with abrasive powder. Supplied complete with automatic pre-set revolution counter and one 7.5 kg weight, but without abrasive powder and thickness measuring device.

Suitable for operation on 415 V, 50 Hz, 3 phase,AC supply7 Compaction Factor

ApparatusCompaction Factor Apparatus for determination of workability determination of concrete mixes of very low workability such as those normally used with concrete, compacted by vibration. Concrete mix having maximum size of aggregate not exceeding 38 mm, can be tested for workability. Compaction Factor Apparatus is complete with hoppers and receiver assembly, Tamping Rod of 16 mm dia X 60 cm long having a Hooper and two trowels.

23,000

8 Cement Tensile Testing Machine

This cement tensile testing machine is primarily used to determine the tensile strength of briquette specimens of cement it can also be used to test the flexure strength of the sample. This test is commonly used by cement manufacturers in order to determine the quality of cement. Capacity 2kN&10kN, Loading speed of the single lever system 10+_ N/Sec, loading speed of the double lever system 50+- 10/sec flexure jaw diameter of the loading roller 10mm supporting roller diameter 10mm supporting roller distance 100mm barrel plate span 46mm

2,56,109

9 Concrete Mixer, Pan Type, Capacity 40L

Concrete Mixer, Pan Type, Capacity 40L 2,41,400

Rs. 1496859.00Transportation Engg. Lab.

10 Benkelman Beam Benkelman Beam with Digital Dial Gauge in Wooden Carrying Case (as per IRC:81), Lightweight aluminium construction.• Ease of Transportation. • Unique Telescopic Design, simplifying field set up. • Compact, thereby reducing the amount of storage space needed. Benkelman Beam utilises the technique of using balanced beam in conjunction with a suitable vehicle to measuring road flexure. The improved Benkelman Beam is a convenient, accurate device for measuring the deflection of flexible pavements under moving wheel loads. Operating on a simple lever arm principle, the unit consists of a Reference Beam, Body, two part Probe Beam and Rear Zero adjust.

38,500.00

11 Flash Point Apparatus Flash Point (Open) and Fire Point Cleveland, ElectricalHeating Thermometer IP 28 C,Range : -6°C to+110°C, Ref. Standards - IS:1448 (Part 69), ASTM D 92, IP 36,BS:4689, ISO 2592,For determining the flash and fire

13,120.00

points of petroleum products, except for fuel oil and those products which have open cup flash point below 79° C (175° F).consisting of Cleveland Flash Cup Brass, with anInsulated Handle. Gas Test-Jet Assembly Correctly positioned and pivoted from a cast cup platform which is fixed to a heating bath. Energy Regulator, To regulate the rate of rise in temperature 220 V, 50 Hz, SinglePhase, AC Supply.

12 Film Stripping Device, Film Stripping Device, is used to measure the resistance of bituminous mixtures to stripping of asphalt from aggregate particles. It is generally used to evaluate mineral aggregates & to judge the adhesion of the bituminous materials. The device consists of a disk on which 4 bottles are mounted. The disc rotates at a speed of approx. 100 rpm. The sample, usually the aggregate fraction which passes a 9.525 mm sieve but is retained on a No. 8 sieve, is placed in the bottles & agitated for 15 minutes. The percentage of aggregate stripped can be visually estimated. The device is provided with a pre set

59,000.00

13 Mastic Asphalt Tester Mastic Asphalt Tester as per IS:1195 90,050.00

14 Sieves Sieves Set 20cm diaSeives 4,75 mm2.36 ,2.00,1.80 mm,1.70 mm,1.00mm,212micron,150 micron,600micron,425 micron, 250 micron,125 micron,63micron,90mic, 75 mic and pan and cover.

20,000

Rs. 220670.00

Soil Machines Lab

15 Hand Operated Extractor

Hand Operated Extractor 38mm mm dia specimen, for 38 mm dia specimens for extracting soil core specimens of 38 mm diafromsampling tube or from larger size samplers. It can be usedin the field also, for taking out samples. Having Sample Extractor Frame Screw Type with a Wire Sample Trimmer Jarring Link for driving the Sampling Tube, Adapter with locking screw for fitting the 38 mm diaSampling,Tube to Jarring Link, Split Mould38 mm dia x 76 mm long, provided with Quick Release Clamps. It can be fitted to Sample Extractor, Sampling Tube,Unrelieved, 38 mm dia x 200 mm long 1 No.

12,000.00

16 Sample ject This Extractor has been specially designed to overcome the difficulties faced in extracting specimens from longer Sampling tubes.

Salient Features:

1,50,000.00

High efficiency hydraulic pump.Power pack with quick release couplings.Manual operation possible on power failure.Ejects soil from sampling tubes and moulds upto 60 cm in length and 38 to 150 mm in diameter by a single operation• Allows direct transfer of soil from field sampling tubes, Proctor and CBR moulds into 38 mm diameter tubes with minimal disturbance.• 60 cm piston stroke.• 50kN pushing force.• Electrical-cum-hand operated or only hand operated hydraulic system.• Built-in safety valve to prevent loading beyond 50kN.• Portable, with facility for floor mounting.• Lever for selecting up/down movement of piston.• Top-plate for holding upto 6 sampling tubes of 38 mm dia.

The equipment consist of the following:

1. Adapter rings/Disk kit - Adapter rings and ejector discs for 38, 50, 75, 100 & 150 mm dia sampling tubes or moulds, included.

2. Sampling Tube, Unrelieved,38 mm dia x 200 mm long

17 Infra-Red Moisture Meter

This moisture meter has been designed for rapid and accurate determination of the moisture content of a wide variety of materials. It is torsion wire instruments, the torque being applied to one end of the wire be means of a calibrated drum to balance the loss of weight as the test sample dries under infrared radiation. The speed of drying (about 30min) thus obtained, combined with the frictionless balancing system gives the result as accurate as those obtained by standard oven drying method. Since drying weighing are simultaneously it is useful especially for determination of moisture in substances that quickly reabsorbs moisture after drying. The infrared radiation is controlled by a voltage regulator and thereby provide excellent heat control. The instrument is provided with as indicator lamp. Which glows when the unit is switched on. The torsion balance has a built-in magnetic damper of reduce pan vibration that enables quick weighing. The balance scale (drum) is divided in terms of moisture percentage on wet weight basis, which are read directly from it. Graduations are from 0 to 100% in 0.2 divisions. But readings may be estimated to 0.1% moisture content. Suitable for operation on 220V n50hz single phases AC supply. Capacity: 5g approx... Sensitivity 10mg approx... Range 0 to 100% moisture content on wet weight basis. Reading accuracy: +- 0.20% Probable error : +- 0.25 in the lower upto compared to 25% and +- 1% for

22,510.00

moisture contents oven methods : above 50%

18 Hydrometer Range Hydrometer, Range : 0.995 to 1 540.00

19 High Speed Stirrer Designed as a compact bench-mounted laboratory stirrer for the pretreatment stage of soils before particle size analysis. The mixer spindle operates within a dispersion cup which can be fitted with an ant splashing baffle to improve the efficiency of mixing. Suitable for operation on 220V 50Hz, single phase AC Supply.

25,050.00

Rs. 210100.00Fluid Mechanics Lab

20 Reynolds Apparatus Dye vessel: Material stainless steel suitable capacity, Tube material borosilicate glass. Constant head water tank capacity 40ltrs. Water circulation: FHP pump. Flow measurement: using measuring cylinder. Sump tank: capacity 60ltrs. Stop watch: electronic. Control panel comprises of standard make on/off switch, main indicator etc. tank is be made of stainless steel.

50,740.00

21 Multipurpose Tilting flume

Pre-fabricated Perspex walled multipurpose tilting flume with following dimensions: length = 6m, width= 0.2m and depth 2m

1,99,000.00

22 Metacentric Height Apparatus

Pontoon: size 300x150mm (approx) with a Horizontal guide bar for aliding weight. Water tank: size 600x400x400mm (approx). Front window of tank: made of glass/perspex. A set of weight is supplied with the apparatus. Tank is made of stainless steel.

40,000

Rs. 289740.00Soil Dynamics Laboratory

23 Block Vibration test setup

Consisting of :

1. Mechanical oscillator with eccentricity Indicator and speed sensor specification : peak Force : 2000 kgf at 45 hz Eccentricity : 0-140 deg. CFrequency Range : 0 to 50 HzStandard IS 5249 : 1992

01 610000 610000

2. Variable speed 5HP D.C Motor specifications : Capacity : 5 H.P. or suitable to drive the mechanical oscillator quoted above for the required frequency range at full loadType : Shunt Motor (220V DC)Coupling Arrangement : ProvidedSelf-Vibration : negligible

3. Speed control unit thyristorised Controlled variable speed drive system with digital LED Display to Drive the DC

Motor Specifications: Speed variation : 50 to 3000rpmLeast count : 1 rpmMad drop in voltage at full load : less than 2%Power source 230 + 10 % 50 Hz AC mains Model : MsCu -1000 Accessories fixing plates, Nuts & Bolts, Belt/Flexible shaft, cables and tools etc. to fix the system for operation.

4. Digital vibration meter specification : Display : 312

Digit

LED Resolution : Acc : 0.1g Disp. : 0.01mm Output : Analog output provided

5. Accelerometer Specification: Accelerometer Range : +-5 g

24 Ultra sonic pulse velocity test equipment

Ultra sonic pulse velocity test equipment, complete with lough polyester carrying Bag. Two transducers (54KHz) Ultrasound couplant. Two 3.6 metre cables power supply and manual 100/240V AC 50/60 Hz complete with free computer interface Kit with reference bar.

01 395000 395000

Optional extra

a) Note. For greater depth. 24KHz transducers are required UTR24kHz. Transducer received 50mm dia X 112mm loag.

b) Note. For shallow depth. 150 kHz, transducers are required UTR 150 kHz 150 kHz, transducer receiver 25mm dia X 34 long. If using with them WAD/3.6 BNO-BNC cable is needed.

01

01

130000

110000

130000

110000

Rs. 1245000.00Fluid Machinery Lab

25

26

2728

1. Centrifugal Pump with 10HP motor kirloskar make fatted with all necerary accessories and attachment such as manometer, officemate and pressure gangeupto 100 gange pressure.

2. Reciprocating pump with 10HP motor kirloskar make fitted with all neccrsary accessories and attachment such as manometer, officemate and pressure gangeupto 500 gange pressure.

3. Manometer set for Francis turbure to measure upto 500 pice

4. Digital tachometer with the range 0 to 5000 rpm

01

01

0101

2,00,000

2,00,000

10,0004300

2,00,000

2,00,000

10,0004,300

Rs. Total 3876669.00

(Rupees thirty eight lakhs seventy six thousand six hundred sixty nine) only.

Sl. Name of Equipment

Total Price (Rs.)No. Specification1

Rebound1,50,000.00

: Measuring Range: 10 - 70 N/mm2 (1'450 to

Hammer 10'152 psi). The following standards can beapplied to the Original Schmidt:

ISO/DIS 8045EN 12504-2ENV 206DIN 1048 part 2BS 1881 part 202ASTM C 80SASTM D 5873(Rock)NFP 18-417B 15-225JGJ(r 23-2001)JG 817-1993

System Features:

• Type N Original Schmidt: Rebound valuesare read from a scale for subsequentCalculation of the mean. Compressivestrength values can be read from aconversion diagram

• Type NR Original Schmidt: Rebound valuesare recorded as a bar chart on a paper stripwhich has a capacity for 4'000 test impacts

• Type L Original Schmidt: Handling equalstype NR but the type L offers an Impactenergy three times srnelle.

• Type LR Original Schmidt: Handling equalstype NR, but with impact energy three timessmaller. The LR also features a paper stripfor recording up to 4'000 test impactswithout reloading

StandardizationThe following standards can be aoolied to theOriginal Schmidt:

• ISO/DIS 8045 • ASTM 0• EN 12 504-2 5873(Rock)

• ENV 206 • NFP 18-417

• DIN 1048 part 2 • B 15-225• BS 1881 part 202 • JGJ/T 23-2001• ASTM C 805 • JJG 817-1993System Technical Spedfication:

Original ScmidtType N

Measuring 10 - 70 N/mm2 (1'450 to 10'152 psi)range

Impact 2.207 Nm

energy .

Make: Proceu Asia Pte Ltd

2 PUNDIT LAB 5,25,000.00Consisting of:Display unit, 2 transducers (54 kHZ), 2 BNCcablesl.5 m (5ft), couplant, calibration rod,USB charger with USB-cable, 4xAA(LR6}batteries, data carrier with software,documentation and carrying case.System Features

• Integrated waveform display

• Remote control: A USB connection and thePundit Link application allow full remotecontrol of all features of the ultrasonic testequipment Pundit Lab.

• Open interface: full remote control of theinstrument is also possible with third partysoftware

• Direct data logging on the PC• Multiple Power Supply Options: the

ultrasonic test equipment Pundit Lab runson battery supply, mains supply via ACadaptor and can also be powered from a PCvia the USB connection.

• Wide range of transducers: The ultrasonic

. test equipment Pundit Lab supports a wide

. range of transducers from 24 kHz. up to 500kHz., making it suitable not only for concreteand rock, but also for other materials suchas graphite, ceramics, woods, etc.Exponential transducers for rough surfacesand shear wave transducers for estimationof dynamic modulus of elasticity completethe portfolio.

System Technical dataTransit time measurement of the ultrasonic test

equipmentRange

0.1 - 9999 us

Resolution o.t psDisplay

79 x 21 mm passive matrixOLEO

Transmitter Optimized energizing pulse 125V, 250 V, 350 V, scov. AUTO

ReceIverSelectable gain lx, lOA, 100x, AUTOstepsBandwidth 20 kHz - 500 kHz

Memory Nan volatHe, > 500 measuredvalues

Regional Settings

Metric and Imperial unitssupported

Power SupplyBattery

4x AA batteries (>20 hourscontinuous use)

Mains Sv, <500mA via USB charger

PCSv, <SOOmA directly via USB

cableMechanical .Dimensions 172 x 5S x 220 rnmWeight 1.316 g (incl. battenes)

Environmental conditions For the ultrasonic testequipmentOperating -100 to 60°C (0° to 1400F)temperatureHumidity <95% RH, non condensingThe ultrasonic test equipment Pundit Lab complieswith the following standards:• EN12504-4 (Europe)

I • ASTM C 597-02 (North America)• BS 1881 Part 203 (UK)• 1501920-7:2004 (International)

• IS13311 (India)

• CECS21 (China)

Software Features :The Windows based software Pundit Link, developedby Proceq, unlocks the full capabilities of theultrasonic test equipment Pundit Lab, providing theuser with:

.' waveform Visualization and analysis turnsyour PC into an oscilloscope.

, • interactive adjustment of trigger point. • on-line data acquisition

• full remote control of the instrumentincluding programmable data loggngfunctionality

• export of data to third party applications

3 I Rebar Locator PROFOMETER 5+ Model 10,50,000.00SCANLOG Basic UnitKey features are identical to Model 5, withadditional key features:'" "Cyber Scan" functions for displaying. thereinforcement.'" "t-1easuring with grid" function for grey-scale display of concrete cover. The objects ofboth functions can be stored, printed outdirectly and transferred to a PC.

Each Basic Unit is identical to Model S withadditional items:• 1 Nos. probe carriage Scan Car with pathmeasuring device and path measuring devicecable 1.55 m f.or scanning,• 1 Nos. Interface converter to printer withparallel Interface, with 2.0 rn cable.Features

• The Profometer 5+ cover meter allows thedetection of rebars

• Measurement. 0' concrete cover depth andrebar diameter

• Correction functens for the Influence ofneighbouring bars

• The cover met r offers optical as well as ,

acoustic locating aids

• Storage of 40'OCO indivrduel cover valuesand statistical analysis (160'000 with modelScanlog)

• Data transfer function from the cover meterto a PC and evluation using the Pro VistaAnalysIs Software, Included with the covermeter,

Applications

• Locate rebars With the cover meter to avoidthem when drilling holes

• Acceptance inspection of cover afterformwork is removed

• Measuring concrete cover depth with thecover meter

• Quality assurance in mass production ofprefabricated concrete elements

• Profometer 5' rover meter Model Scanlog Isespecially suited for large areas and whencomprehensive reporting is required

System Technical Data:non-volatile memory for 40'000

Memory measured values 160'000) and 60objects respectively

.. Display LCD with bac light, 128 x 128 pixelI t fa RS 232 or with adapter for USB Port on

n erce PCS ft Pro Vista for downloading data and

o ware evaluation on PCBattrI six 1.5 V for 45 h operation; 30 h with

e es backlight onMeasuring Range of the cover meterOperating temperature -0 °C to +60 °c

Storage temperature -10°C to +60 -c

Cover depth small range up to 100 mm

measurements (3.94 in.)large range up to 185 mm(7,28 m.)

. up to a cover of 70 mmDiameter measurement (2.76 in.)

StandardizationThe following standards n be applied to the cover

meter:• BS 1881 • SN 505262

part 204 • DGZfP B2• DIN 1045 (recommendation)

Including 390 00 270 Test block4 Canin+ instrument with Device cantn, carrying5,50,000.00

strap, transfer cable, USB adapter. operatinginstruction, rod electrode, caninprovista software.Measuring Range: 0 to 99kncmResolution: lKOcm

ELECTRICAL ENGINEERING DEPARTMENT(C)

Sr No. Name Of Machine Technical Specification DEMAND Rate Amount Remarks

1 Computer System

Intel Processor core i3 or i7 or latest with mother board Intel Chipset 41/61 latest with

4 USB,1 Serial port, 1 LPT port, 2 GB RAM DDR III,500 GB SATA Hard Disk,18"LCD/LED Monitor,Desktop Cabinet with SMPS , DVD writer.Keyboard,USB Mouse,1 GB Network card or latest configuration with microsoft

windows pre loaded

25 pcs

2 UPS 10 KVA Online,6 Hrs Backup with battery 02 pcs

3 Three phase Auto Transformer

15 KVA,Input 415 V,3 phase,50 Hz,Output0-415V,30 A per line,Cooling Air natural 10 pcs

4 Single phase Auto Transformer(Dimmerstat)

Single phase,AirCooled,enclosed model Input:0-230 Volts,10 A Output 0-270 Volts 10 pcs

5 Wattmeter

Portable Type, Accuracy Class-1,

140 mm long Mirror scale Range: 2.5/5A 300V

LPF Type,P.F=0.2

10 pcs

6 Rehostats

Wire wound resistors,Variable,Three terminals. With steel clamp+Brush type

moving contact ±5% tolerance 400Ω ,1A 100Ω,5A 150 Ω,2A

110 Ω,2.5A 40 Ω,5A

20 Ω,10A

05 pcs each

Sr No.

Name Of Equipment Technical Specification DEMAND Rate Amount Remarks

1 Split Type Air Conditioner

1.5 T with suitable stabilizer 5 star rating with installation,make:Samsung/Voltas/LG/Haier 03 pcs 50,000 1,50,000

2 Photo Copier Machine

copy,print, color scan speed 25 ppm A3 size,256 MB RAM,Duplex, Make xerox/ricoh/canon 01 pcs 1,40,000 1,40,000

3 HP color Laser Jet printer Model M252 DW 01 pcs 37,000 37,000

4 Printer laser jet HP laser Jet 1160 or equivalent 02 pcs5 LCD Projector 4.43/PAL/SECAM, with PC interface and audio interface 01 pcs6 Printer Cartridge Mak HP laser Jet P1606dn 06 pcs 5,400 32,4007 Inverter with UPS 1000 VA Make Sukam/Lumionous/Exide/Microtech 03 nos 6000 18,0008 Tubular Battery 12V 180 AH Make:Exide/Sukam/Luminous/ 04 nos 16000 64,0009 Ceiling Fan 1400 mm Make:Havells/USHA/Polar/Crompton 12 nos 2500 30,000

10 Double Tube light set Make:Philips/Havells 15 nos 1000 15,000

11 Water purifier RO-UV-UF Capacity 7-8 ltsMake:Kent/AquaGuard/Hind Lever 1 nos 20,000 20,000

12 PVC Wire coil 4mm Make: Havells/Anchor 04 coil 4500 per coil 18,00013 PVC Wire coil 2.5mm Make: Havells/Anchor 02 coil 2500 per coil 5000

14 Switch Board with AC stator 03 pcs

15 Casing Capping pipes 100 ft

16 MCB 32 A Make:Havells/Anchor 03 pcs17 PVC Tape Make Steel Grip/Anchor Blue Black 10 pcs 10 100

18 Electrical Tool kit setConsisting of Combination plier,Long Nose plier,Cutter, Nose

Plier,Round Nose Plier,Screw driver set,Philips Screw driver,Rawlplug,poker,plumbbob,hammers,Haksawetc

04 pcs

19 soldering Iron Set 25 watt with solder wire, flux,Makesolderon 04 pcs 150 60020 Hydrometer 02 pcs 100 20021 Electric bulb 100w Make:Philips/Bajaj/Surya 50 Pcs 15 75022 Fire Extinguisher Specially for Electrical fire 04 pcs

Sr No.

Name Of Appratus Technical Specification DEMAND Rate Amount Remarks

1 Function generator1 MHz

20 MHz 100 MHz

02 pcs each

2 Solarbotics L 298 H-Bridge board with appropriate connectors 02 pcs each

3 PIC kit 2 with appropriate connectors and driver 02 pcs each

4 RS-232 cable compatible with PCs serial port and dsPIC board's serial port connector i.e DB-9 connector 02 pcs each

5 Power supply ±15 V,3A 02 pcs each

6Bread Board

Development system

Bread board system with DC power O/P 5 V,± 12 V and 0-5V variable,digitalvoltmeter,Ammeter,LED indicators 8 nos,Logic

input switches 08 nos,7-segment display 2 nos,clock generator Manual pulser,Potentiometer, Relay etc with about 1600 bread

board points with suitable digital IC's for logic gates,flipflop,shiftregisters,countersetc

25 pcs

7 Trainer Kit for Digital IC's

Trainer kit shall consist of digital Ics for logic gates,FlipFlop,shiftregisters,counter along with toggle switches

for input and bi-color LED at outputs,built in power supply25 pcs

8 Microprocessor kit 8085

With Logic Interface cards of 8085 microprecessor kit with appropriate connectors 20 pcs

9 Dual DAC card for 8085 10 pcs

10 PIC micro-contrroller Model:PIC 16F877A with appropriate software and connectors 05 pcs

11 Power Factor Meter Single Phase 5-10 A,250 V 05 pcs

12Microcontroller

trainer kit (IC-8051 based)

Intel 89C51 operating at 12 MHz Onboard crystal 12MHz for oscillator 1 & 1.8432 MHz for oscillator 2 Onboard GM16C550 for Asynchronous serial communication 32 KB onboard user

program memory 12 KB battery Backed up user program memory

16KB battery Backed up user data memory 40 Characters X2 lines LCD display controlled by 89C2051 supports esxternal

ASCII keyboard Onboard +5V,+12 V,-12V Dc for peripheral card. Timer counter chip(8253),two counters available for users. Two 8255 chips,giving 48 TTL I/O lines.all signal s terminated on two

26 pin FRc connectors. port P1 pins brought out on 10 pin connectors for user interface. Serial port RS-232 compatible usin

8250,sinals terminated on a 9-pin D-connector. Address ,Data and control bus available on 50 pin FRc connector for expansion.

supports follwing modes of operations: (i)Interrogation mode :for interactive dialog with system (ii) assembler mode:line assembler inbuilt in monitor(iii) single step

mode:useful for single stepping,inserting/removing breakpoints and debugging.powerful monitor software with standard

commands like MOVE,FILL,DISPLAY/MODIFY REGISTERS,EXECUTE PROGRAM,UPLOAD/DOWNLOAD etc.Single

line assemblers/dis-assembler.Software LCD outinesinEPROM:Clearscreen,Row Column, Display

Character,ReadColumn,ReadRow,Display a Message,Cursoroff,CursorOn,Read Keyboard&Display,Read

Keyboard vstatus,Read string &Display,Keyboard Flush.

05 Pcs

13Trainer board for

IC-555 Multivibrator

trainer consists of IC-555 and various components to build circuit of astable,monostablemultivibrator with variable

frequency and power supply and patch cords2 pcs

14Trainer Board for

OP-Amp applications

Trainer kit suitable to demonstrate the working of Op-Amp741 in various modes like inverting amplifier,Non-Inverting

Amplifier,Adder,Substractor,Integrator,Differentiatoretc.Required R and C components provided in trainer which can be

interconnected by patch cords to make the desired configuration.2 Nos of variable DC power supplies, inbuilt offset

adjust facility,inbuilt DC regulated Power supply

20 pcs

15 Lamp Bank 230V,0-20 A 02 pcs

16

Synchronous Motor protection

scheme(Both field and armature)

01 pcs 11,000 11,000

17

Synchronous Generator protection

scheme(Both field and armature)

01 pcs 11,000 11,000

18 IDMT Relay(i) solid State

(ii) Electromagnetic (iii)Microprocessor based

01 pcs each 11,000 33,000

19 Differential Relay 01 pcs 11,000 11,000

20 Class A,B,C and AB amplifiers 05 pcs 5,000 25,000

21 Two stage R-C

coupled transitor amplifier

05 pcs 4,000 20,000

Sr No. Name Of Software Technical Specification Demand Rate Amount

Remarks

1 MATLAB Software Complete Toolbox for 25 users licensce 1 no 10,00,000

10,00,000

2 LABVIEW Software Complete Toolbox for electrical Engineering with25 users licensce 1 no

3 Bray's terminal software 2 users licensce

4 GNU Octave 2 users licensce5 Multi Sim Software 25 users licensce 1 no 5,75,00

05,75,00

0

6 PSIM SoftwareConsisting of PsimBasic,Digital Control

Module,Motor Drives module with 5 user licensce

1no 5,85,000

5,85,000

7 UniversityPogram For Micro Tutor Embeded lab

Consisting of Tutor set(8051 and PLC Tutor Set)-1 user each, IDE o 8085/PLC-5

User,EDUTECH Educational Practice BOARD FOR 8051-5 USERS,EDUTECH Educational Practice BOARD FOR PIC18F4455-02 nos,

Application Specific kit-01 user each with & -segmet Led interfacing kit, RTC-EEPROM

Interfacing KitGeneral purpose I/o board,Traffic Light CpontrollerKit,Basic Input-Output module,Relay Interfacing Kit,Touch

Screen Interfacing kit,Stepper motor kit

1 no 3,95,000

3,95,000

8 Antivirus Softaware 40 user licensce 1no 80,000 80,0009 Pspice software 25 users licensce

10 MS-office 2010 5 user licensce 1no

11 Microcontroller simulation Software

Suitable simulation software to perform micro controller system programming 10 user licensce copy or open

source software1no

12 C Compiler suitable for micro controller programming 10 user licensce copy or open source software 1no

Sr No. Name Of Furnitures Technical Specification Deman

dRate

Amount

Remarks

1 Wooden Arm Chair with Cushion 15 pcs 5000 75000

2 Computer Table Make: Zuari /Godrej 25 Pcs

3 Computer Chair Make: Zuari /Godrej 25 pcs

ELECTRONICS & COMMUNICATION ENGINEERING DEPTT.

(D)

Total

632000.00

Basic Instruments,Devices&Ics for all Labs of ECE Dept.

S.N. ITEMS WITH SPECIFICATION UNITPRICE (Rs)(Approx)

QTY AMOUNT(Rs)

1. Digital Multimeter 3.5 digit Metravi 702 1700.00 50 85000.002. General Purpose Power Supply:0-150 VD.C., 10 Amp

(variable)DC Output

15000.00 5 75000.00

3. Universal Electronic Trainer kit with 4(four) Bread Board; Power Supply :analog (AC& DC)constant &varriable and Digital 8 bit Input ; display: Digital 8 bit Input & output

15000.00 16 240000.00

4. Universal IC Tester NB 9350 26000.00 01 26000.00

5. 10 MHz Function GeneratorFrequency Range:0.5Hz to 10MHz;Resolution:10MHz;Waveforms;Sine,Square;Traingle,Ram,Pulse;DC Offset; AM/FM; 40MHz Auto Ranging Frequency Counter.

19000.00 04 76000.00

6. Spectrum Analyzer 100 MHz 130000.00 01 130000.00

Analog &Digital

Electronics Lab ECE

S.N. ITEMS WITH SPECIFICATIONUNITPRICE(Rs

)(Approx)

QTY AMOUNT

1. CE Amplifier with built in variable frequency Oscillator 4000.00 02 8000.002. BJT amplifier with controlled characteristics Training

Kit 6000.00 03 18000.00

3. Boolean Algebra Trainer with Power Supply 6000.00 03 18000.00

4. Logicgate Training Board with Power Supply 4000.00 03 12000.00

5. TTL Logic gates(NAND & NOR) structure – Training

Kit 5000.00 03 15000.00

6. CMOS Logic gates(NAND & NOT) structure – Training

Kit 5000.00 03 15000.00

Basic Electronics & Power Electronics Lab ECE

S.N. ITEMS WITH SPECIFICATION

UNITPRICE

(Approx)

QTY AMOUNT

1. Diode &Zener Diode Characteristic Trainer kit 7000.00 02 14000.002. Clipper & Clamper Training Kit 5000.00 03 15000.003. Transistor Characteristic(CB,CE,CC) Trainer

kit 7000.00 05 35000.00

4. Transistor Switching CharacteristicTrainer kit 5000.00 03 15000.005. OP-AMP Characteristics& Applications

Trainer9,000.0

0 05 45,000.00

6. SCR Characteristics Apparatus 6000.00 03 18000.00

7.SCR Triggering Technique Trainer kit

6,000.0

003 18000.00

8. Multivibratorastable,monostable&Bistable experimental Kit

11000.0

003 33000.00

Total1,93,000.00

7. 4-Bit Binary Full Adder &Substractor with Power Supply 5000.00 03 15000.00

8. 4 Bit binary Dicad Up/Down counter using with Power

Supply LTB 857 using IC 74/92 omega5000.00 03 15000.00

9. Study of various encoders and Decoders with Power

Supply3500.00 02 7000.00

10. Wein Bridge Oscillators Trainer 5000.00 02 10000.0011. Frequency Meter Training Kit 11000.00 02 22000.00

12. Connecting wires for digital laboratory of different color

with thin pin120 50 6000.00

Total 161000.00

Analog& Digital Communication LabECE

S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx)

QTY AMOUNT

1. Sampling & Reconstruction (standard comp.)Trainer 9,500.00 03 28500.00

2. TDM Pulse Amplititude Modulation/Demodulation Trainer 11000.00 03 33000.00

3. TDM Pulse code modulation Transmitter

Trainer15,000.00 02 30000.00

4. TDM Pulse code modulation Receiver Trainer 15,000.00 02 30000.00

5. Adaptive Delta And Delta Sigma modulationAnd Demodulation Trainer 20,000.00 02 40000.00

6. Data Formatting And carrier modulation/Transmitter Trainer 11000.00 03 33000.00

7. Data Reformatting And carrier DemodulationReceiver Trainer 11000.00 03 33000.00

8. DSB/SSB Suppressed carrier AM Transmitter Trainer 11000.00 03 33000.009. DSB/SSB AM Receiver Trainer 11000.00 03 33000.0010. AmplititudeModulation And Demodulation

trainer 11000.00 03 33000.00

11. FDM Trainer: frequency division multiplexing &Demultiplexing with sinusoidal &Audio Input.

11000.00 03 33000.00

12 QPSK Trainer Kit 17000.00 02 34000.00

13 FSK Trainer Kit 17000.00 02 34000.0014 BPSK Trainer Kit 17000.00 02 34000.0015 PCM Trainer kit 11000.00 02 22 000.0016 Super Hetrodyne Receiver 11000.00 03 33000.00

Total 494500.00

Electronics Instrumentation & Measurement LabECE

S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx) QTY AMOUNT

1. Bench LCR MeterSpecification: Five-terminal measuring technology;It can measure - inductance (L)Capacitance(C), resistance (R), quality factor(Q) and dissipation factor (D).With a basicAccuracy of 0.25% and five digit displayResolution

45,000.00 01 45,000.00

2. Single Phase Watt Meter 3200.00 01 3200.003. Maxwell's Bridge Trainer Kit 6000.00 02 12000.00

4. Kelvin's Bridge Trainer Kit 5,500.00 02 11000.00

5. Hey's Bridge Trainer 6,000.00 02 12000.00

6. Moving Coil Galvenometer 1000.00 05 5000.00

7. PMMC Voltmeter 1000.00 05 5000.00

8. Temperature Transducer Trainer – Thermocouple

based

15,000.00 02 30000.00

9. Pressure Transducer Trainer 19,000.00 01 19000.00

10. Ultrasonic Transducer Trainer 14,000.00 01 14000.00

11. Frequency meter Training Kit 11000.00 02 22000.00

12. Schering Bride Aquile/Lale Make with built in 8000.00 02 16000.00

regulated

Power supply 230v,AC

13. Measurement of temperature with Thermister 6000.00 02 12000.00

14. Linear variable differential transducer (L.V.D.T) 4500.00 02 9000.00

15. Optical transducer trainer Omega type ICT-904 5500.00 02 11000.00

16. CRO Trainer Board having block tracing facility with

various test points

25,000.00 02 50,000.00

Total 2,76,200.00

Digital Signal Processing LabECE


QTY AMOUNT

1. DSP Lab Version 2Features:Based on TMS320C6713 processor.Sampling & Waveform GenerationQuantizationPCM EncodingDelta ModulationDigital Modulation Schemes (ASK, PSK, FSK)Error Correcting CodesRead Write from CODECFast Fourier TransformFIR Filter implementation (Low P ass, High Pass, BandStop)IIR Filter implementationLinear ConvolutionAuto CorrelationPower Spectral DensityPlay Sound, Echo, Echo with FadingMultiple Echo, ReverberationSound MixingOn board Switch and LED InterDSK 6713-MATLAB Interface facing Program with DSK 6713

55,000.00 02 110000.00

2. DSP Development PlatformFeatures:External 5 V DC power supplyIEEE 1284 compliant male-to-female cableCode Composer Studio DSK toolsStudy and Analysis of FIR FilterLow Pass, High Pass, Band Pass, Band Stop filterStudy and Analysis of IIR FilterButterworth Approximation, Chebychev ApproximationStudy and Analysis of Adaptive FiltersLMS Algorithm, Noise CancellationStudy and Analysis of Digital Modulations TechniqueQAM, BPASK, PSK, FSKInterface MATLAB (Simulink )with 6713Read-Write using Simulink-6713Smart Tech-Book model.Smart E-manual for easy understanding.

70000.00 02 140000.00

3. DSP Development Board.Features:High performance 32 bit, TMS320F2812 Digital SignalController32 x 32 bit or dual 16 x 16 bit MAC8-stage fully protected pipelineFast interrupt response manager128Kw on-chip flash memoryCode Security Module (CSM)Two event managers56 shared GPIO pinsWatchdog timerCommunications peripherals12 channel PWM12 bit 16 channel ADC moduleInterfacing with Stepper Motor, Servo Motor, DCmotor.Interfacing with Character LCD and Graphic LCD.Interfacing with Temperature sensor and relay.Interfacing with DIP Switch and LED.Smart Tech-book Model.Smart Manual for easy understanding.DSP Technology learning software.

80000.00 02 160000.00

Total 410000.00

Microprocessor LabECE


QTY AMOUNT

1. 8051 Microcontroler Training Kit with in-built P.S. 12000.00 03 36000.00

2. 8085Micro processor Training Kit within built Power

Supply ;opcode input facility.

20000.00 05 100000.00

3. 8251 Serial Data Interface card 2600.00 03 7800.00

4. ADC Peripheral interface study Card 2600.00 03 7800.00

5. DAC Peripheral interface study Card 2500.00 02 5000.00

6. Temprature Control interface card 7000.00 02 14000.00

7. Seven Segment Display Interface Card 7000.00 02 14000.00

8. Stepper Motor control Interface Card 3500.00 02 7000.00

9. DC motor speed controller Interface Kitek IC – 14 7000.00 02 14000.00

Total 205600.00

. Electronics Software LabECE


QTY AMOUNT

1. Micro Tutor DSP Embedded lab▪ All in one DSP educational practice Boardwith code composer Studio for DSP …………..… 5 No.▪USB TAG Simulator………………….. 5 No.▪ Color CCD Camera…………………. 1No.▪ Interactive work book …………….... 1 No.▪ Application specific kits for DSP …… 4 No.

---

Total

Set

3,50,000.00

2. Lab View -measurement and instrumentation software latest version license for 5 PC

- - 3,00,000.00

3. Turbo C 2,500.00 01 2,500.00

4. M.S. Office 2007 11,000.00 10 1,10,000.00

5. Visual basic 6.0 11,000.00 01 11,000.00

6. Multi Sim latest version license for 25 PC - - 5,75,000.00

7. Vis Sim-com Software latest version license for 10PC - - 4,85,000.00

8. MATLAB Software Latest VERSION license for 20 PC

- - 3,00,000.00

9. Multimedia Projector1.Multimedia Projector Resolution: 1024 x 768 x GA, Lumens 30002.15 Meter VGA Cable3.Laser Pointer

55000 01 55,000.00

Total 21,38,500.00


QTY AMOUNT

1. Godrej Bench Desk ( Seat, front & back – wooden) 18000.00 100 1800000.00

2. Godrej Gadda Arm Chair 4000.00 30 120000.00

3. Godrej Executive Table 24000.00 15 360000.00

5. Wodden Stool ( 2 6 ×1 × 1 4 )′ ′′ ′ ′ ′′ 1000.00 30 30000.00

Total- 2310000.00

Digital Class Room ECE


QTY AMOUNT

1. Interactive BoardDiagonal size 92

75,000.00 04 3,00,000.00

2. Laptop HPIntel core15, 4GB ram, latest HDD & OS,15.6 LED

45,000.00 04 1,80,000.00

3. Digital PodiumMultimedia Digital Podium with Visualizer, PC Connector and audio system - Two collar microphone & One on podium

65,000.00 04 2,60,000.00

4. Laser Printer with Scanner & Xerox 45000.00 02 90,000.005. Multimedia Projector

1.Multimedia wireless Projector, good Resolution, Lumens 30002. Mounting Kit&Ceiling mounted Bracket for projector3. Remote &Laser Pointer

45000 04 1,80,000.00

6. A.C. Split 1.5T [ Voltas/Samsung ] 25,000.00 16 4,00,000,00

7. Vacuum CleanerMake:Eureka Forbes

25,000.00 01 25,000.00

8. False Ceiling of 4 Class Rooms: (30´×40´) , (30´×40´) (25´×26´) & (30´×51´)

200.00/sqft 4580sq ft 9,16,000.00

9. Electrification of False Ceiling with power points and mounting lights(CFL)

8000.00/room 04 32,000.00

10 Curtains of windows and Doors 5000.00/room 04 20,000.00

11. Installation & Digital Class Room Developling charge

15,000/room 04 60,000.00

Total 25, 03,000.00

Grand Total

(E) CSE Deptt. B.C.E., BHAGALPUR

1 SCO Unix Server 5.0.7 with 25 users licence. Desktop SCO Unix 25 O/S Rs. 85,000.00

Needs Purchase of Oracle Enterprise Edition (12G)

with 25 user licence

2Rational Rose Enterprise Edition with 25 users licence.

Desktop Rational Rose 25 Software Rs. 70,000.00

Needs Purchase of Rational Rose Enterprise

Edition with 25 user licence.

3 Informatica with 25 users licence Desktop Informatica 25 Software Rs. 75,000.00

Needs Purchase of Informatica with 25 user

licence

4 Oracle 12 G with 25 users licence Desktop Oracle 12 G 25 Software Rs. 2,00,000.00 Needs Purchase of Oracle

12 G with 25 user licence

5 One SCO Unix Server N/A SCO Unix Server 1 Hardware Rs. 1,50,000.00 Needs Purchase of One

SCO Unix Server

6 Window A.C..

Window A.C. 7 1.5 ton Rs. 30,000.00 Rs. 2,10,000.00

7 Split A.C. Split A.C. 6 1.5 ton Rs. 45,000.00 Rs. 2,70,000.00

8 Curtain for 11windows Curtain 11 N/A Rs. 2,500.00 Rs. 27,500.00

9 Curtain for 3 doors Curtain 3 N/A Rs. 2,500.00 Rs. 7,500.00

10 Palmet for 11windows Palmet 11 N/A Rs. 1,500.00 Rs. 16,500.00

11 Palmet for 3 doors Palmet 3 N/A Rs. 1,500.00 Rs. 4,500.00

12 Fans 20 N/A Rs. 2,000.00 Rs. 40,000.00

13 Pedestal Fans 2 N/A Rs. 3,500.00 Rs. 7,000.00

14 Blowers 2 N/A Rs. 5,000.00 Rs. 10,000.00

15 Fire Extinguisher 2 N/A Rs. 10,000.00 Rs. 20,000.00

16 AMC with spares for Computers 50 N/A Rs. 4,500.00 Rs. 2,25,000.00

17Antivirous(Norton Complete Security 360)

50 N/A Rs. 25,000.00

18 Door Catcher For Digital Classroom 4 N/A Rs. 2,500.00 Rs. 10,000.00

19 Cushion Seats for Gallery 150 N/A Rs. 8,000.00 Rs. 12,00,000.00

Total Cost Rs. 26,53,000.00

(G) LANGUAGE LAB FOR 30 STUDENTS

S.No. Particulars Rate Qty. Amount

1 Table Size 2 x 2 x 2.5 with Keyboard Tray and 2 x 1.5 8160 x 30 244800

06 mm Transparent Glass three sides

2 Revolving Chair for Computer 6,500 x 30 195000

3 Computer I3 processor, 4GB Ram, 500 GB HDD, DVD 40,000 x 30 1200000

Writer, 18.5 inch Monitor, Keyboard, Mouse

4 Cat 6 Cable under PVC Channel, I/O Box, Switch, Patch 3,800 x 30 114000

Cord-1m & 2m. RJ-45 Connector for each Computer / WI-FI

5 Headphone with Mike,webcam and Antivirus for each Computer 3,000 x 30 90000

6 Electrical Point for each Computer 3,500 x 30 105000

7 Software for language lab for 30 Computers with Console 350000 x 1 350000

8 10 KVA online UPS with 02 hours backup 3,50,000 x 1 350000

9 PVC Flooring 1.5mm thickness Supply & Pasting. 100 x 2000 200000

10 AC withStablizer for Language Lab, required AC 04 no. with Stablizer. 50,000 x 4 200000

11 False Ceiling with Strong Arm, Gypsum Board, complete finishing 3,50 x 1000 350000

12 Ceiling Light 2/2 Feet make Bajaj, Philips, Havells. 10,500 x 10 105000

13 Blind / Parda as per Requirment. 6 x 8 160 x 48 7,680

TOTAL = 3511480

(H)SMART CLASS LAB FOR 60 NOS. OF STUDENTS

S.No. Particulars Rate Qty. Amount1 Chair with Writing Pad 6, 500 x 60 390000

2PVC Flooring 1.5mm thickness Supply &Pasting ( for Area of 1,500 to 2,000 Sqft.)

100 x 2000 200000

3AC withStablizer for Language Lab for 1,500 to 2000 Sqft Area, required AC 04 no. with Stablizer.

50,000 x 4 200000

4 False Ceiling with Strong Arm, Gypsum Board, complete finishing3,50 x 2,000 Sqft. 700000

5 Projector for Smart Classes with Remote 1, 00, 000 x01 1000006 Digital Sound System for Smart Classes With Mike Set. 1, 25, 000 x 01 1250007 Smart white interactive Board for Smart Classes of diagonal 78" 1, 20, 000 x 01 120000

8 Laptop / Desktop Computer I7 processor, 4GB Ram, 01 TB HDD, DVDR/W 70,000 x 01 70000TOTAL 1905000

Three (03) Smart classes are proposed Grand Total =1905000 X 03 =

5715000

ANNEXURE 2Digital library

The system is structured to expose students to multifarious learning experience and opportunities that challenges and maximizes their learning

potential. Providing education digitally and making it available to everyone every where is the main function of Digital Library. The teachers get the

relevant digital resources such as animations and videos, interactive virtual labs tools etc. and use them as a part of their lesson plans in every

classroom period. Learners can use the digital library to view content at their own choice post class hours. The basic aim is to provide a complete

system with easy to use interface which will manage all videos, reference document, resources, digital content to centralize all the learning recourses of

the academy and provide end users a unified platform for viewing. It is Propriety Item. The price of Digital Library (Online): E Repository7 + 2500

Courses + 85,000 Lectures + 1000 e-Books + 5000 Exams is Rs 9,50,000/- (Nine lakh fifty thousand).

ANNEXURE 3

Training Need Analysis/ Software Requirements for Students and Teachers of BCE Bhagalpur

S.N. Departments Subject Related Training and Software

7 • Enroll - Provide login id and password to your students and teachers and enroll them.• Study plan - Create a path of his/her own learning• Follow - Follow any teacher, course, channel to be updated about their latest advancements• Personalized Digital Library – Create your personalized digital content library.• Integration – This solution provides integration with the Digital lecture studios in thecampus, Campus Management System and the Campus Wide Networking.• Increase star rating - Favouratise or like a lecture, teacher or course and increase its starrating.• Comment - Post comments and seek others comments and viewpoints

1. Mechanical CAD/ CAM Software ( Computer added Design and computer added Manufacturing ) Software for Mechanical EngineeringFinite Element Analysis Software for Stress Analysis , Mechanical vibration, Fatigue Motion, Heat transfer, fluid flow, electrostaticsSoftware for Machine Design: - Solid Edge (Complete Hybrid 2D/3D CAD system for accelerated Design, faster change.Project Planning software in Mechanical EngineeringPro/ Engineer Software for DesignSAP ( System, Application & Product) SoftwareERP ( Enterprise Resources Planning) SoftwareMechatronics software for Machine Design and RoboticsBig Data Analytics softwareSoftware for Automotive Design and manufacturing process with Design simulation softwareSoftware for basic of Robotics System and its DesignCATIA Software ( Computer added 3 Dimensional interactive application)Programming: C++Cloud Computing SoftwareMATLAB Software

2. Civil Auto CAD for Civil EngineeringS TAAD Pro for structural Analysis and Design of StructureProgramming: C++MATLAB softwareFinite Element Analysis Software for Stress Analysis , Mechanical vibration, FatigueETABS for Building Analysis and Design softwareSAP 2000 for dynamic AnalysisPrimavera Project Planner software for Construction ManagementCSI SAFE software designing Concrete floor and foundation SystemMXRoads software for designing all types of RoadsCloud Computing SoftwareVisual basic software for generation of graphicsGIS software solution for civil EngineeringCloud Computing Software

3. Electrical ETAB software for Design , power Management, Substation

Automation , Load shedding etc.Auto CAD for Electrical DesignELECDES for Electrical DesignSmartDraw software for designing electronic circuit, Automotive wiring, Circuit Schematics and designing digital circuits.Programming: C++MATLAB softwareSoftware for Estimating Electrical ProjectsEasyPower software for short circuit calculationsCloud Computing Software

Training requirements

Power System DesigningTransformer DesigningControl System DesignEmbedded system Design

4 Electronics and Communication ECAD : VLSI Design Software

Programming: C++Advanced JavaMATLAB softwareXilinx ISE for analysis of HDL DesignsCloud Computing SoftwareVIDE software for designing , testing and debugging Verilog applVHDL softwareIE3D, Antenna softwareFPGA KitXUP VirTEX OPEN SPARC BOARDIAR Embedded workbench Mcos/os II and II

Training requirements Web Development

Printed Circuit Board (PCB) DesigningPLC ( Programming Logic Control)Power System DesigningControl System DesignEmbedded system DesignEthical Hacking & Cyber SecurityMicrocontroller & MicroprocessorsAutonomous Robotics, 6th sense Robotics

5 Computer Science And Engineering Programming: C++

Advanced JavaMATLAB softwareCloud Computing Software

Training requirements

Web DesigningDesign and Analysis of AlgorithmsComputer Languages like C++,Java, Linux,Development of computer and hardware systemFoundation of Software EngineeringAndroid Application DevelopmentEthical HackingCyber SecurityCloud Computing

Common Training Need Analysis Requirements for Students, supporting staff and Teachers of BCE Bhagalpur

1. Soft Skill Development: Soft skills revolve around personal relationships, character, and attitude. By developing these skills, students may increase their performance, build stronger relationships, and work toward achieving objectives of life.

2. Training for doing experiments through virtual Lab

3. Communication skills

4. Personality Development: Taking Control of our Life with the Science of Personal Development.

5. Training of Fundamental Science for weak students

6. Basic Computer skills for faculty, staff and students

Training Need Analysis Requirements for supporting staff &Teachers of BCE Bhagalpur

(C)

Lesson planning

Improving Teaching Skill (Including Micro Teaching Sessions)Effective Teaching Methods and ICT enabled learningMotivating Student for LearningLaboratory/Workshop Instruction DesignStudent Performance EvaluationDesigning Questions (Development of Question Bank)Student Counselling & Career GuidanceApplication of Computer/IT in educationEducational PsychologyInstructional material developmentClassroom ManagementWriting research proposalsTraining psychologyUndertaking systemic researchOrientation/Refresher/Induction PorgramsCurriculum Development & Implementation relatedDevelopment of competency based curriculum in technical coursesDesign of question bank for effective implementation of currculumInnovative approaches in curriclum designManagement/Institutional Management/Communication relatedTQM in Institutional ManagementInstitutional DevelopmentDevelopment of Quality management system (QMS)/ ISO 9001:2008 in technical institutionsProject Planning & Management for teachersDeveloping Interpersonal Relationship in OrganizationsMaking effective presentationHuman resource development & managementPersonality DevelopmentImproving Communication/soft skill in day to day transactionsEnvironmental Awareness/Education/management including ISO 14001 2004 for teachersProcess of Accreditation in technical educationPlanning & implementing staff training program in institutionsManagement for general office staffOrganized problem solving & decision makingManagement principles for technical teachers

Development and use of Instructional mediaTeam Building & team performanceTeachers role in entrepreneurship development among students

Note: Expenditure for procurement of any equipment and furniture will not be admissible if procured with Government of Bihar Supports or any other

sources.

Expenditure for any Civil Work activity will not be admissible if undertaken with other sources.

Additional operating cost if required will be borne by the Department of Science and Technology.

The above activities are only indicatives

Procurement and Foreign Visits will be approved by SPFU and NPIU.

For all other activities Institutes should have full freedom to execute the action.

Documents

TEQIP-II Agenda