Maintenance Parts

Temperature Sender Product Type: Maintenance Parts

Product Description The coolant temperature sensor/sender is used to measure the temperature of the engine coolant of an internal combustion engine. The readings from this sensor are then fed back to the engine control unit (ECU), which uses this data to adjust the fuel injection and ignition timing.

AVR or Automatic Voltage Regulator Product Type: Maintenance Parts

Product Description Automatic voltage regulator maintains a constant power value emission at every point during its use for the protection of the generator itself.

Oil Pressure Sender Product Type: Maintenance Parts

Product Description The engine oil pressure sender/sensor measures the integrity of the engine lubrication system and responds to changes in engine oil pressure, displayed via operation of the oil pressure light or gauge.

Rear Oil Seal Product Type: Maintenance Parts

Product Description A rear main seal, also known as a main seal or rear main bearing seal is located between the engine and transmission and keeps the engine oil from escaping.

Front Oil Seal Product Type: Maintenance Parts

Product Description Front end oil seal for engine crankshaft, engineered to ensure a perfect seal, maximum contamination exclusion. Delivers a long lifetime of load endurance and seal efficiency.

Rocker Cover Gasket or Cylinder Head Cover Gasket Product Type: Maintenance Parts

Product Description A rocker cover gasket helps seal the joint between the rocker cover and the rest of the engine. Failure of this gasket can cause oil to leak from the engine.

Alternator Belt or Dynamo Belt Product Type: Maintenance Parts

Product Description Alternators are used in modern automobiles to charge the battery and to power the electrical system when its engine is running.

Fan belt Product Type: Maintenance Parts

Product Description An endless belt used to transmit power from a crankshaft-driven pulley to a pulley driving the fan, alternator, or other engine accessory. It is usually V-shaped in cross section with the point of the V fitting into a groove in the pulley.

Water Filter or Coolant Filter Product Type: Maintenance Parts

Product Description A coolant is a fluid which flows through or around a device to prevent the device from overheating, transferring the heat produced by the device to other devices that either use or dissipate it.

Oil Filter Product Type: Maintenance Parts

Product Description An oil filter is a filter designed to remove contaminants from engine oil, transmission oil, lubricating oil, or hydraulic oil. This results in longer equipment life and more reliable operation.

Air Filter Product Type: Maintenance Parts

Product Description A particulate air filter is a device composed of fibrous materials which removes solid particulates such as dust, pollen, mould, and bacteria from the air. Filters containing an absorbent or catalyst such as charcoal (carbon) may also remove odors and gaseous pollutants such as volatile organic compounds or ozone.

Overhaul Parts

Tappet Product Type: Overhaul Parts

Product Description Tappet, also termed a cam follower or lifter, runs on the camshaft and is made to move vertically by the action of the rotating cam. In an overhead valve engine, this tappet is fitted low down in the engine block.

Pushrod Product Type: Overhaul Parts

Product Description A rod in a piston engine that actuates rocker arms above the cylinder head.

Rocker Shaft/Arm Product Type: Overhaul Parts

Product Description A rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement at the poppet valve to open it.

Bottom Overhaul Gasket Kit Product Type: Overhaul Parts

Product Description Complete gasket kit including all the required gaskets and seals to complete an overhaul of the bottom or lower end of the engine, typically include sump, oil filter and cooler, oil pump, fuel pump, water pump, fuel lift pump, oil seal, timing case gaskets together with pipe seals and gaskets.

Top Overhaul Gasket Kit Product Type: Overhaul Parts

Product Description Top overhaul kits, along with other complementary kits, are designed to work together to bring you the right overhaul solution. This kit consists of the principal wear parts of the typical engine. It consists of basic parts that can be exchanged (overhaul of cylinders).

Valve Guides Product Type: Overhaul Parts

Product Description In most types of reciprocating engines, a valve guide is provided for each poppet valve in the cylinder head. Along with the valve spring, it serves to positively locate the valve so that it may make proper contact with the valve seat.

Valve Stem Seal Product Type: Overhaul Parts

Product Description The Valve Stem Seals are rubber seals which go around the top of the valves to prevent oil seeping down the valve stem to the combustion chambers where it can burn. After years of heating and cooling in the engine these seals become brittle and begin to leak. The most common symptom of this is a little smoke on start up, plus increased oil consumption.

Exhaust Valve Product Type: Overhaul Parts

Product Description A valve through which burned gases from a cylinder escape into the exhaust manifold.

Inlet Valve Product Type: Overhaul Parts

Product Description The valve through which a fluid is drawn into the cylinder of a positive-displacement engine, pump, or compressor. Also known as induction valve.

Con Rod Bush Product Type: Overhaul Parts

Product Description Con rods, or connecting rods, transfer the power generated by the engine’s pistons to the crankshaft, which then operates the machinery it’s connected to.

Con Rod Bearing Product Type: Overhaul Parts

Product Description A modern internal combustion engine operates at high speeds and temperatures, and this requires a connecting rod bearing robust enough to withstand them. Friction bearings are made from metal to reduce friction when the pistons are turning the crankshaft.

Connecting Rod Product Type: Overhaul Parts

Product Description Connecting rods form the link between the crankshaft and the pistons which transfer the gas and inertial forces to the crankpins on the crankshaft. The connecting rod pushes and pulls the piston into and out of the cylinder.

Piston Ring Kit Product Type: Overhaul Parts

Product Description Connecting rods form the link between the crankshaft and the pistons which transfer the gas and inertial forces to the crankpins on the crankshaft. The connecting rod pushes and pulls the piston into and out of the cylinder.

Piston Kit Product Type: Overhaul Parts

Product Description A kit contains a piston, a piston ring, a piston pin and cir clips.

Liner Product Type: Overhaul Parts

Product Description The liner is an enclosed area and a part of the combustion chamber where the fuel is burnt and heat energy is transmitted to kinetic energy by use of piston, crosshead, bearings and crankshaft.

Crankshaft Product Type: Overhaul Parts

Product Description A crankshaftis a mechanical part able to perform a conversion between reciprocating motion and rotational motion. In a reciprocating engine, it translates reciprocating motion of the piston into rotational motion; whereas in a reciprocating compressor, it converts the rotational motion into reciprocating motion.

Parts Kits

1000 Hour Service Kits Product Type: Parts Kits

Product Description This kit includes spare parts of proven quality, and it is cost efficient with extended equipment lifetime.

2000 Hour Service Kits Product Type: Parts Kits

Product Description To keep your compressor operating at its very best, you have to perform the scheduled maintenance as outlined in your manual. This cost efficient kit has a lower cost than purchasing the items individually.

5000 Hour Service Kits Product Type: Parts Kits

Product Description This maintenance kit is “Block Specific”, designed for a specific compressor block model. It reduces breakdowns and compressor idle times and has a proactive approach to inventory management.

Long Engine Product Type: Parts Kits

Product Description Occasionally, engines can fail and during a complete engine failure, the long engine kit is there to provide you with a solution.

Short Engine Product Type: Parts Kits

Product Description Engines are designed to last for many years but if your engine does fail, it is quick and simple to obtain a replacement short engine that will minimise your downtime and get your equipment back up and running swiftly.

Recommended Parts Kits Product Type: Parts Kits

Product Description Genuine parts helps maintain engine performance and ensure a productive life with a complete range of maintenance and repair products.

Overhaul Kits Product Type: Parts Kits

Product Description A complete overhaul of your engine takes place very rarely. If you do decide to undertake this process, overhaul kits have been designed to complement other parts kits offerings to ensure you have the right parts for the job.

Repair Parts

Radiator Product Type: Repair Parts

Product Description Radiators can be repaired. If the radiator is in good shape overall both core and tank leaks can be repaired. If the core is rotten but the end tanks appear good you can install a new core in no time.

Turbo Chargers Product Type: Repair Parts

Product Description Turbochargers provide boost to engines at high speeds.A small turbocharger will provide boost more quickly and at lower engine speeds, but may not be able to provide much boost at higher engine speeds when a really large volume of air is going into the engine.

Water Pumps Product Type: Repair Parts

Product Description The role of the water pump in an engine is primarily to regulate its temperature and to prevent the engine from overheating. It pumps water and coolant through the engine block and cylinder head (the main body of the engine) via a series of pipes, drawing out the heat generated, before going into a radiator.

Lift Pumps Product Type: Repair Parts

Product Description The primary fuel or lift pump moves the diesel fuel from the tank into the fuel system and provides the initial fuel pressure. It ensures the correct flow rate and pressure to prevent the cavitation and vaporization that can lead to damage.

Electronic Sensors Product Type: Repair Parts

Product Description Sensors and senders help control diesel engine function providing information and feedback on fuel and air flow, exhaust gas flow and content as well as temperature and pressure so that the diesel engine can operate efficiently, and maintain emissions standards.

DC Alternator Product Type: Repair Parts

Product Description The alternator is an integral part of the electrical system for your engine. It continually recharges the battery while the engine is running, ensuring that it never loses power. The alternator also regulates the power going back into the battery so it doesn’t become overcharged.

Starter Motor Product Type: Repair Parts

Product Description The starter motor provides the power needed to begin the compression sequence in the diesel engine. It takes its charge from the electrical system and is constantly recharged while the engine is in operation.

Deep Sea Products

DSE6020MKII Product Type: Deep Sea Products

Product Description The DSE 6020 MKII is an Auto Mains (Utility) Failure Control Module developed to provide a wide range of operating and monitoring features for single diesel and gas gen-sets.ets. OVERALL SIZE: 216 mm x 158 mm x 43 mm (8.5” x 6.2” x 1.5”) PANEL CUTOUT SIZE 184 mm x 137 mm (7.2″ x 5.3″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.48kg PRODUCT VARIANTS 6020-03 – MKII Auto Mains (Utility) Failure Control Module 6020-04 – MKII Auto Mains (Utility) Failure Control Module (Htr)

Leroy Somer Alternator Parts

Leroy Somer – LL8224 Product Type: Leroy Somer Alternator Parts

SERIAL NO. DESCRIPTION QTY.

PMG 5 FOR R450 MATE N LOCK 1

SPARTNER KIT 1

PMG 5 FOR R448 V50 1

Connection kit for AVR R450M and 1

SPACE HEATHER 500W / 230V 1

1 FAN 1

2 LIFTING EYE 1

3 D.E. BRACKET SAE 0 1

3 D.E. BRACKET SAE 00 1

4 AIR EXIT SCREEN 1

5 N.D.E. BRACKET 1

6 TERMINAL BOX PANEL 8200 H, L, N & P 1

7 TERMINAL BOX PANEL N.D.E. 1

8 TERMINAL BOX LID H, L, N & P 1

9 ACCESS DOOR 1

10 AIR INLET SCREEN 1

11 N.D.E. BEARING 6315 2RSC3 1

12 OUTER BEARING COVER 1

13 INNER BEARING CAP 1

14 BORELLY RING 1

15 WOUND EXCITER FIELD 1

16 WOUND EXCITER ARMATURE 1

17 DIODES BRIDGE SUPPORT 1

17 DIODES ASSEMBLY KIT 1

17 M.O. VARISTOR 1

17 DIODES KIT 1

18 TERMINAL SUPPORT 1

19 TERMINAL BLOCK WITH 1

20 PHASE BUSBAR 1

21 NEUTRAL BUSBAR 1

22 AVR R450M 1

22 AVR R450T 1

23 DRIVING HUB KEY 1

24 COUPLING DISCS SAE 18 1

25 COUPLING SHIM THICKNESS 1

26 RUBBER O RING 215X5 1

27 LEFT SIDE PANEL 8200 H, L, N & P 1

28 RIGHT SIDE PANEL 8200 H, L, N & P 1

29 AVR ACCES PANEL 1

30 STATOR ASSEMBLY 8224 P AREP wdg 6 1

30 STATOR ASSEMBLY 8224 N AREP wdg 6 1

30 STATOR ASSEMBLY 8224 L AREP wdg 6 1

30 STATOR ASSEMBLY 8224H AREP wdg 6 1

31 ROTOR ASSEMBLY8224 P 1

31 ROTOR ASSEMBLY8224 N 1

31 ROTOR ASSEMBLY8224 L 1

31 ROTOR ASSEMBLY8224H 1

Leroy Somer – Surge Suppressor Product Type: Leroy Somer Alternator Parts

Product Description The Surge Suppressor, is a protection device, which prevents high voltage transients from damaging the main rectifier diodes. High Voltage transients are created by fault conditions in the distribution system. The Voltage transient returns back to the Generator output terminals, enters the main stator windings, and by mutual inductance, is transferred to the main rotor windings, and the main rectifier assembly. The Surge Suppressor can be tested with a Multimeter on Megohms range. A good Surge Suppressor should have a very high resistance, (more than 100 Megohms in either direction). A faulty Surge Suppressor will be either open circuit (usually showing signs of burning) or short circuit in both directions.

Leroy Somer – Diode Assembly Product Type: Leroy Somer Alternator Parts

Product Description The diodes on the main rectifier assembly can be checked with a multimeter. The flexible leads connected to each diode should be disconnected at the terminal end, and the forward and reverse resistance checked.

The rectifier assembly is split into two plates, positive and negative, and the main rotor is connected across these plates. Each plate carries 3 diodes, the negative plate carries the negative based diodes, and the positive plate carries the positive based diodes. Care must be taken to ensure that three identical polarity diodes are fitted to each plate. When fitting the diodes to the plates they must be tight enough to ensure a good mechanical and electrical contact, but should not be over tightened.

Leroy Somer – AVR Product Type: Leroy Somer Alternator Parts

Product Description Leroy-Somer AVRs benefit from all Leroy-Somer’s experience in the electronics field. They have been designed to comply with market requirements in terms of characteristics, performance, conformity with standards and reliability.

Their main characteristics are : • Simple, user-friendly user interfaces • Power switching transistor offers an optimum response to interference generated by distorting loads • Voltage regulation ±0.5% in steady state with rapid response time (< 500 ms) • Optimised mechanical design for resistance to vibration and harsh environments, with coated electronic circuits • Conformity with IEC 60034-1 and UL 508 Systems that help take account of load impact/load shedding are built into Leroy-Somer AVRs. U/f function • Load impacts taken into account • Instant response from the AVR below the underspeed threshold • Gradual voltage return to rated voltage

LAM function • Load Acceptance Module • Reduction in voltage drop and duration of speed variation of the diesel engine • Possible increase in the applied load for the same speed variation • Adaptive tuning LAM for load impacts > 60%