Technisonic Industries TDFM-136. TDFM-136 Transceiver Operation TDFM-136 Transceiver Operation

Technisonic IndustriesTDFM-136

TDFM-136 Transceiver Operation


TDFM-136 Transceiver Operation - Overview

Radio Familiarization

Front Panel Layout and Controls Basic Operation Channel and Memory Select

Programming the Radio

Command Architecture Operating Commands Channel Data Commands Configuration Commands

PC Software Use (TDP-136)

Connections Operation


Radio Familiarization - Front Panel Layout and Controls

1. Squelch Indicators (LED) – Lights when signal is received.2. Channel Display (2Line x 24 character) – Shows channel parameters.3. MAIN (Rotary+Switch) – Power ON/OFF and Main channel volume control.4. GUARD (Rotary) – Guard channel volume control.5. Squelch Defeat (Push button) – Press to open squelch (in analog modes of operation)6. MN/GD (Toggle Switch) – Selects active channel (Main or Guard) for transmit and edit functions.7. G1/G2 (Toggle Switch) – Selects active Guard memory G1 or G2 for transmit and edit functions.8. HI/LO (Toggle Switch) – Selects Transmit Power: High (10w) or Low (1w).9. Keypad (12 Keys) – Control radio functions, 3 command levels.


Radio Familiarization – Channel Display

1. Main channel information is displayed on the top row of the display.

2. Guard channel information is displayed on the bottom row of the display.

3. The Main channel can have up to 230 memory positions (001 to 230), the current active memory number for the Main channel is shown in the first three characters of the line.

4. The Guard channel can have two memories, GD1 and GD2, the currently active Guard memory number is shown in the first three lines of the bottom row.5. Memories for the Main channel can be scanned, when in use scan information is shown at the 4 th character position on the top row.6. The current command level is indicated on the bottom row at the 4 th character position.


Radio Familiarization – Channel Display

The following parameters are common to both the Main and the Guard channels.

7. Up to eight characters are available for a text description of the memory.

8. One character position is used to indicate the operating mode: Analog modes: wide "w"(25kHz.), narrow "n" (12.5kHz.) Digital mode: project 25 digital "D" (12.5kHz.).

9. Eight characters are used to indicate the frequency in use.

10. One character indicates either Receive or Transmit as: "R" or "T".

11. The final character indicates the current squelch mode: Analog modes: noise squelch "x", CTCSS tones "t", DCS codes "c" Digital modes: monitor "m", NAC only "n", and TalkGroup + NAC "g"


Radio Familiarization – Basic Operation

The basic operation for transmit and receive is as follows:

1. The Squelch LED's are on if a valid signal has been received.

2. Upon keying the radio, the "R" character at the second from right position on the line, will change to a "T". The character will revert to a "R" upon releasing PTT.

3. The "MAIN" and "GUARD” receive audio volumes are separately controlled.

4. In analog modes the "SQUELCH" pushbutton opens the squelch, in digital it opens upon receiving any valid digital signal.

5. The transmit power level can be set to 1W (low) or 10W (high).


Radio Familiarization – Select Channel and Memory

1. The MAIN channel data is shown on the top line of the display, MAIN supports 230 memory positions (001 to 230). MAIN is selected for edit and transmit by placing the MN/GD switch in the MN position.

2. When the MAIN channel is selected, a specific memory may be selected by pressing the "CHAN" key and then directly entering the memory number (001-230), or by using the forward or backward arrow keys (6 & 4) to scroll through the programmed memories.

3. The GUARD channel has two memories: GD1 and GD2. When the MN/GD switch is in the GD position then the GUARD memory used is determined by the position of the G1/G2 switch.


Command Types

There are two types of commands: inherent and edit.Inherent commands need no further input from the user (example: display brightness commands)Edit comands need further input from the user and must end as follows:

Accept the changes, save and exit

Abandon the changes and exit

Command Levels

The commands are organized into levels, there are three operator command levels (1-3), a Maintenancelevel (4), and a Supervisor level (5). Command levels are indicated at the 4 th character on the bottom row.

Command levels are navigated as follows:

go up one level

go down one level

Command levels 2 and 3 are time limited, if a command is not selected within 5 seconds the unit returnsto command level 1 automatically. When a level 2 or level 3 command is completed, the timer is resetand the radio remains on that command level until a command is selected, ESC is selected or time out.


Programming the Radio – Command Architecture

Command Scope

The commands can be characterized as belonging in one of three categories:Operating commands are those which perform a direct function related to the use of the radio.Edit comands allow the user to Edit the RF channel parameters (frequency, mode etc).Configuration comands affect how the radio operates, including how other commands work.


Programming the Radio – Command Architecture

Command Nomenclature

The commands and command levels are abbreviated as follows:Command Levels are abbreviated as Ln, where 'n' is the level number from 1 to 5.

example: L2 = command level 2

Command Numbers are abbreviated as -n, where 'n' is the command number from 0 to 9.example: L2-1 = command level 2, command 1 (Edit all/new channel)

Command Description

The commands are described in detail in both the Technisonic documents:TDFM-136 Operators Manual, (TiL document #99RE266) and theTDFM-136 Installation and Operating Instructions, (TiL document #99RE255)

These documents are available on-line at www.til.ca.

http://www.til.ca/

Operating Command List

The Operating Commands are distributed across Level 1, Level 2 and Level 3 as follows:

Level 1L1-1 jump to selected channelL1-2 and L1-8 change display brightnessL1-4 and L1-6 scroll through programmed memories on MAIN channelL1-5 start/stop scan

Level 2L2-2 copy current GUARD channel data to current MAIN channel.L2-3 lock keypadL2-8 copy current MAIN channel data to current GUARD channel.

Level 3L2-9 display current Squelch Parameters.


Programming the Radio – Operating Commands


Programming the Radio – Edit Commands

Edit Commands - Cursor and Prompts

When any Edit begins, a cursor is placed in the appropriate data field on the display, and the non-activechannel becomes a prompt line.

Example: for 'Edit Frequency' on the MAIN Channel, a cursor is placed at the second character in theFrequency field (1), and the Guard display row becomes a prompt line (2).

When editing the Guard frequency, the situation is reversed, the cursor is placed on the GUARD row (1), and the MAIN row becomes the prompt line.


Programming Channel Data – Edit Commands

Edit Command List

The Edit Commands are distributed across Level 1 and Level 2 as follows:

Level 1L1-3 Edit current Operating Mode (analog wide, analog narrow, P25 digital).L1-7 Edit current Frequency (136.0000 to 174.0000 MHz.)L1-9 Edit current Squelcy mode (analog or digital depending on current Operating Mode)

Level 2L2-1 Edit all current channel or Create New Memory (MAIN only).L2-5 Edit Scan list (MAIN only).L2-6 Edit current Text Description.L2-7 Create Shadow Channel (MAIN only).L2-8 Edit Unit ID.


Programming Channel Data – Configuration Commands

Configuration Command List

The Configuration Commands are Level 3 and Level 4 as follows:

Level 3L3-1 Set Boot Memory for MAIN (Last Selected, Last Programmed).L3-3 Set HEX / Decimal Edit for TalkGroup & NAC.L3-4 Show current firmware version.L3-5 Set Scan Parameters (revert mode, reply timer, monitor timer, delay timer).L3-6 Set PTT Max Timer (30, 60, 90 seconds).L3-7 Set Sidetone AudioL3-8 Communicate with PC (for PC programming).


Programming Channel Data – Configuration Commands

Configuration Command List – continued

Level 4 (Maintenance Level – protected access)

L4-1 Set channel defaults for Edit all.L4-2 Memory test.L4-3 Restrict Operator Level Commands.L4-4 Channel Scroll test (MAIN only).L4-7 Re-build RF Database (tries to rebuild corrupted database in RF modules).L4-8 Erase All Memories and Re-boot (Set to as shipped from factory).L4-9 Restrict Squelch Options.


PC Software TDP-136

Setup

1. PC with serial port, or USB-Serial converter

Operation

Note that the TDP-136 manual is available on-line at www.til.ca.

1. Follow Manual Instructions, available on-line.

Note: the TDFM-136 does NOT work with MultiTDP, you must use TDP-136.

http://www.til.ca/


?? Questions ??

TDFM-136 Operator’s Guide

See www.fs.fed.us/fire/niicd/documents.html

TDFM-136 PC Cable

NIICD TDFM-136 Cheat SheetTDFM-136 Basic Programming Instructions Software Version 2.x.x

August 16, 2005 1. Change To A Previously Programmed Channel:

1) Press or . Or

1) Press .

2) Press desired preset channel number such as for channel 34.

3) Press .

2. Load New Frequency: 1) Set MN/GD switch up for Main (MN) programming and down for Guard (GD) programming.

2) Press .

3) Push keys corresponding to desired receive frequency (omitting the 1) and press .

4) Push keys corresponding to desired transmit frequency (omitting the 1) and press .

3. Load Tone: 1) Set MN/GD switch up for Main (MN) programming and down for Guard (GD) programming.

2) Press .

3) To enter a receive tone, follow the below instructions. Otherwise press .

a. Press to toggle between receive no tone (Rx) and receive CTCSS tone (Rt) and press .

b. If “Rt” was selected, press the and keys scroll through CTCSS tones and press .

4) To enter a transmit tone, follow the below instructions. Otherwise press .

a. Press to toggle between transmit no tone (Tx) and transmit CTCSS tone (Tt) and press .

b. Press and keys scroll through CTCSS tones and press . 4. Change Bandwidth:

1) Set MN/GD switch up for Main (MN) programming and down for Guard (GD) programming.

2) Press until narrowband “n” or wideband “w” is displayed. The “D” is for P25 digital. Default is “n” for all frequencies.

3) Press .

Note: All federal VHF-FM frequencies are 12.5 kHz (narrowband) as of January 1, 2005. Operating on an effected federal frequency in the wideband mode after this date relegates the user to a “secondary”, or non-interference, basis. Additionally, wideband and narrowband compatibility issues may inhibit effective communication.

See www.fs.fed.us/fire/niicd/documents.html

NIICD TDFM-136 Configuration Settings

L-4-3 Permissions for Standard (GD Disabled) Radio Configuration Level 1

Select MN Memory

Brighter Edit OP Mode

MN Memory

DN

Scan MN Memory

UP

Edit Frequency

Dimmer Edit Squelch

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ● ● ● ● ○ ● ● ○ ● ● ●

Level 2 Create/Prog

All Copy GD to MN

Lock Keypad

Not Used

Edit Scan List

Edit Text

Create Shadow

Copy MN to GD

Edit Unit ID

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ○ ○ ○ ○ ● ○ ○ ○ ○ ○

Level 3 Set MN

Boot Memory

Upload to PC

Set Hex/Decimal

Show Version

Edit Scan

Param

Set PTT Timer

Set Sidetone

Level

Download from PC

Show Squelch

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ● ● ● ○ ○ ● ● ●

● = Enabled/on ○ = Disabled/off

L-4-3 Permissions for Guard Enabled Radio Configuration Level 1

Select MN Memory

Brighter Edit OP Mode

MN Memory

DN

Scan MN Memory

UP

Edit Frequency

Dimmer Edit Squelch

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ● ● ● ● ○ ● ● ● ● ● ●

Level 2 Create/Prog

All Copy GD to MN

Lock Keypad

Not Used

Edit Scan List

Edit Text

Create Shadow

Copy MN to GD

Edit Unit ID

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ● ● ○ ○ ● ● ○ ● ○ ○

Level 3 Set MN

Boot Memory

Upload to PC

Set Hex/Decimal

Show Version

Edit Scan

Param

Set PTT Timer

Set Sidetone

Level

Download from PC

Show Squelch

1 g 2 g 3 g 4 g 5 g 6 g 7 g 8 g 9 g ● ● ● ● ○ ○ ● ● ●


L-4-9 Configuration Options – All Radios Analog RX Tone ● Analog TX Tone ● Digital RX NAC ● Digital TX IDCall ○ Analog RX Code ○ Analog TX Code ○ Digital RX Talkgroup ● Digital TX Inhibit ○ Analog TX Inhibit ○

Value Edit: Noise ○ CTCSS Tone xx.x ● DCS Code xxx ● L1 Setting Value Edit: Tone ● Noise Squelch 15 Value Edit: Code ○ L2 Setting Value Edit: Monitor ○ Sidetone 52 Value Edit: NAC ● L3 Setting Value Edit: Talkgroup ● Time-out-Timer 90 Value Edit: IDCall ○


See www.fs.fed.us/fire/niicd/niicd_contacts.html for Avionics contact information

Documents

Technisonic Industries TDFM-136. TDFM-136 Transceiver Operation TDFM-136 Transceiver Operation