TECHNICAL TRAINING 2007. SMART COMMANDER System Requirements CPU : 800MHz and aboveCPU : 800MHz and above Memory : 256MB RAM or HigherMemory : 256MB

Technical Training 2007Technical Training 2007

TECHNICAL TRAINING TECHNICAL TRAINING

20072007


SMART COMMANDERSMART COMMANDER


System Requirements

• CPU : 800MHz and aboveCPU : 800MHz and above

• Memory : 256MB RAM or HigherMemory : 256MB RAM or Higher

• Hard Drive : 4G or higher for hard disk spaceHard Drive : 4G or higher for hard disk space

• OS : Windows 2000/XPOS : Windows 2000/XP

• Resolution : 1024 x 768 Resolution : 1024 x 768

• Monitor : Larger than 15 inch, & 17 inch is Monitor : Larger than 15 inch, & 17 inch is recommendedrecommended

• Serial port & USB port availableSerial port & USB port available


User Login• Install the driver of encrypt USB keyInstall the driver of encrypt USB key

• Driver file: SP1730RC9.zipDriver file: SP1730RC9.zip

• Default user name: adminDefault user name: admin

• Password: mcquaymds (can be amend)Password: mcquaymds (can be amend)


Menu Introduction

File MenuFile Menu

• ““Exit” onlyExit” only

Function MenuFunction Menu

• Initiating: Hardware changesInitiating: Hardware changes

• Error History: to record the faults in the system Error History: to record the faults in the system

• User Manager: to manage the user name & User Manager: to manage the user name & passwordpassword

• Parameter Setting: to set parameter of the Parameter Setting: to set parameter of the systemsystem

• Prompts for the units runningPrompts for the units running


ID Monitor

From the 1From the 1stst tab on the left, user can perform tab on the left, user can perform related operation to the ID connected to ODrelated operation to the ID connected to OD

1. Select OD follow by ID 1. Select OD follow by ID

2. Select ID operation2. Select ID operation

3. Adjust ID temperature 3. Adjust ID temperature

4. Turn ON / OFF4. Turn ON / OFF

5. Click “Confirm” to achieve operation 5. Click “Confirm” to achieve operation

6. Double click to see Real Time Fault 6. Double click to see Real Time Fault


Grouping & Timer

1. Click 1. Click

2. Select Default group number 2. Select Default group number

3. Select ID number3. Select ID number

4. Click to select the customized group 4. Click to select the customized group number (Max member in a customized is number (Max member in a customized is 4848))

5. Add the selected ID to the customized group5. Add the selected ID to the customized group

6. Edit the customized group name & ID name6. Edit the customized group name & ID name

7. Click “Edit” button to enter Timer setting7. Click “Edit” button to enter Timer setting

8. Timer Mode Setting8. Timer Mode Setting


System Monitor

From the 2From the 2ndnd tab on the left, user can control the ID tab on the left, user can control the ID & OD & OD

1. Double click the ID icon. A window will pop up 1. Double click the ID icon. A window will pop up

2. Right click the ID icon, user can lock the ID2. Right click the ID icon, user can lock the ID

3. Indication of model icon 3. Indication of model icon


Circuit & Server Monitor

Please connect Please connect ENCRPT USB KEYENCRPT USB KEY of PC, then of PC, then connect to Smart Commander software for connect to Smart Commander software for debugging.debugging.

Using service Using service ENCRPT USB KEYENCRPT USB KEY will not display will not display Circuit Monitor & Server Monitor. Please use Circuit Monitor & Server Monitor. Please use customer software after debugging. customer software after debugging.

Customer software will only display ID control & Customer software will only display ID control & system monitor interface.system monitor interface.


Circuit Monitor

Used to monitor ALL parameter of ID & ODUsed to monitor ALL parameter of ID & OD

• Observe ALL parameter of OD through collect Observe ALL parameter of OD through collect address codeaddress code


Circuit Monitor

• OD parameterOD parameter Single, Master, Slave

Cooling, Heating, Defrost, StopDisplay OD program

OD output capacity (Include Slave)OD output capacity (Include Slave)

TTsh_outsh_out: OD superheat: OD superheatDigital compressor output %Digital compressor output %

OD Fan: Stop, Low, HighOD Fan: Stop, Low, HighHS: High Pressure (bar)HS: High Pressure (bar) LS: Low Pressure (bar)LS: Low Pressure (bar)

Heating electronic expansion valve

Subcool electronic expansion valve

Bypass way valeHigh pressure / Low pressure switch


Circuit Monitor

• OD parameterOD parameter

TH1: Discharge air temp

TH2: The 1st condenser entering temp

TH3: The 1st condenser middle temp

TH4: The 2nd condenser entering temp

TH5: The 2nd condenser middle temp

TH6: Entering water temp

TH7: Heating water temp

TH8: Outdoor temp

TH9: Temp before subcool

TH10: Temp after subcool

TH11: Subcool loop exit temp

TH12: Suction temp

Sensor is Sensor is unavailableunavailable


OD System Theory Diagram

OD address numberOD address number RedRed Line: Heating Line: HeatingGreenGreen Line: Cooling / Dehumidify Line: Cooling / DehumidifyBlack LineBlack Line: Stop: Stop

Sensor position is hint positionSensor position is hint position


ID System Diagram Parameters

Click “Up” or “Down”, Click “Up” or “Down”, ID address number will ID address number will move up or downmove up or down

Click “Back Page” Click “Back Page” or “Next or “Next Page”, the page will Page”, the page will turn up or downturn up or down

Address number of IDAddress number of ID


ID System Diagram Parameters

Click “Ctrl” to set IDClick “Ctrl” to set ID• Choose optional parameters to control single unit Choose optional parameters to control single unit • Optional mode: Stop, Cooling, Heating, Dry, FanOptional mode: Stop, Cooling, Heating, Dry, Fan• Fan Speed: Low, Medium, High & AutoFan Speed: Low, Medium, High & Auto• Assistant function: Aux heater, Swing & LockAssistant function: Aux heater, Swing & Lock


Circuit Monitor

1.1. Modify OD parameters settingModify OD parameters setting

• Defrost curve A, B point. Default setting A is Defrost curve A, B point. Default setting A is -6 -6 °C, B is -24 °C°C, B is -24 °C

• Defrost Finish Temp: defrost stop when TH9 Defrost Finish Temp: defrost stop when TH9 achieve this tempachieve this temp

• Defrost Interval Time: defrost stop when Defrost Interval Time: defrost stop when compressor runs for this interval time compressor runs for this interval time

• TscA1, TscA2, TscT1, TscT2, TscT3TscA1, TscA2, TscT1, TscT2, TscT3When TH9 ≤ TscA1, subcool is TscT1When TH9 ≤ TscA1, subcool is TscT1

When TscA1 < TH9 ≤ TscA2, subcool is TscT2When TscA1 < TH9 ≤ TscA2, subcool is TscT2

When TH9 > TscA2, subcool is TscT3When TH9 > TscA2, subcool is TscT3


Server Monitor• Used to obtain graph for parametersUsed to obtain graph for parameters

• Observe operationObserve operation

• Input or Output data from parameters file Input or Output data from parameters file

• Max. 5 parameters will be displayedMax. 5 parameters will be displayed

• 5 colours on top left indicate the parameters5 colours on top left indicate the parameters


Server Monitor

Coordinate code name

Idiographic machine address code• 1 digit – OD• 2 digit – ID

Detail parameter name

Y- axis scale


Server MonitorFunction Button:Function Button:

Page of display section

No. of pages

Go back to 1st page

Go back to previous page

Go to next page

Go to the last page

Go to parameter setting

Output data


Wiring Connection


Thank YouThank You


Error History Record


User Manager

To add user:• Key in user name• Key in password

1. Click “Add”

To modify:• Key in user name• Key in new password

1. Click “modify”

To delete user:• Select the user in the list

1. Click “Delete”


Parameters Setting

System shut down 3 minutes when switching from “cool” to “heat” or vice versa

Min. running time before switching to another mode

Lock screen interval time - Unit in seconds- Unlock password: mcquaymds

Click this will shown as follow


Parameters Setting


Stage History


ID Monitor


ID Monitor

1. Choose number of the OD

2. Choose number of the ID


ID Monitor

Multiple Control ：

Single Control： Select a indoor unit only

Select many indoor units

Group Control ： All the indoor units in the system


ID Monitor

Select fan speed:(must select)

Select mode (must select)

Select assistant functions:


ID Monitor

Click “ ” or “ ”, can adjust the set temperature

Select “ ” or “ ”, can turn on or close the units

Click “ ”, can send the order to the units


ID MonitorThe error list window pops upThe error list window pops up::


Group Set & Timer


Group Set & Timer

Select OD

Click on the cell to select ID


Customized Group Setting



After select the ID, click this button To delete

the selected ID, click this button



To edit customized group name:

1. Key in group name

2. Click “Refresh”

To edit ID name:

1. Key in ID name

2. Click “Refresh”


Timer Setting

To add/delete the timer mode:

1. Key in name

2. Click “Add” or “Delete”

Select Timer Mode

To Add, Delete or Modify a task


Timer SettingFirst mode: Select ON/OFF task First mode: Select ON/OFF task


Timer SettingSecond mode: Select only “Second mode: Select only “ONON” or only “” or only “OFFOFF” ”


Timer Mode Setting

1. Select ID

3. Click “Set”2. Select Mode


System Monitor


System Monitor


System Monitor

Left click to select the locked function


System Monitor


Circuit Monitor


Circuit Monitor

Defined defrost area

Defrost stop

2nd defrost start after 1st defrost

TH9 ≤ TscA1, subcool is TscT1TH9 ≤ TscA1, subcool is TscT1TscA1 < TH9 ≤ TscA2, subcool is TscT2TscA1 < TH9 ≤ TscA2, subcool is TscT2TH9 > TscA2, subcool is TscT3TH9 > TscA2, subcool is TscT3


Server Monitor

Value of the parameters

Move the pointer to the desired point


Server Monitor

Y1~Y5: parameter setting:

Tick to select ID parameter to be displayed

Max. value of Y-axis

Min. value of Y-axis

Major unit

Display the data of selected date

Display the data of real time

Click to display the graph

Input file


Server Monitor

Output Data:

Documents

TECHNICAL TRAINING 2007. SMART COMMANDER System Requirements CPU : 800MHz and aboveCPU : 800MHz and above Memory : 256MB RAM or HigherMemory : 256MB