Table of Contents - GLLS · FA-XX-BN-XXA-CXX-M FA-XX-PL-XXA-CXX-F FA-XX-PL-XXA-CXX-M Optional Accessory: Anti-Wicking Ferrule The anti-wicking ferrule is located 115mm (±5mm tolerance)

www.ledneonflex.comwww.GLLS.com

E347880

Version 1.1

Table of ContentsSpecifications 2-3

Technical Specifications 2-3

Physical Specifications 3

Part Number Naming 4

Packaging 4

Connectors 5-7

Seamless 5

Snap 6-7

Male and Female 7

Mounting Hardware 8-9

Standard 8

Plastic 8

Spring Clip 9

Flexible 9

Testing 10-11

Certifications 10

Fixture Testing 10

Charts 11

For More InformationToll Free: 1 (888) 580-6366

Or Visit www.GLLS.com /contact-us/

www.ledneonflex.comwww.GLLS.com2

Technical SpecificationsLight Dimension 0.45 x 0.83in (11.5x21mm) Output RGB RGBW(27K/30K/40K) LED Light SMD LED Chip SMD LED ChipMax Run Length *1 *2

Single Feed (Dynamic) 65.62ft (20m) 49.21ft (15m) Single Feed (Full Load) 49.21ft (15m) 32.81ft (10m) Double Feed (Dynamic) 131.24ft (40m) 98.43ft (30m) Double Feed (Full Load) 98.43ft (30m) 65.62ft (20m)

Light Surface Square profile 160°Lumen Maintenance 70,000 Hours L70 @ 25°C : 90,000 L50 @ 25°C 50,000 Hours L70 @ 50°C : 70,000 Hours L50 @ 50°CElectricalInput Voltage 24V DC 24V DCPower Consumption 3.66W/ft (12W/m) 4.57W/ft (15W/m) PhysicalLED Count 17 LED/ft 17 LED/ft (56 LEDs/m) (56 LEDs/m) LED Spacing 0.7in (17.8mm) 0.7in (17.8mm) Cutting Unit Length 4.92in (125mm) 4.92in (125mm) (7 LEDs) (7 LEDs) IC Type UCS2903 UCS2904 Thermal Management Free air convectionFixture Connections End, side & bottom lead wiresMinimum Bend Diameter 4.72in (120mm) (Side Bending)Temperature RangesInstallation -40°F to 122°F (-40°C to 50°C)Operating -40°F to 131°F (-04°C to 55°C)Humidity 0-95% non condensingDependabilityWarranty 5 Year Limited WarrantySafetyCertification Tested to UL & CSA by Underwriters Laboratory for use in USA and Canada, complies with California Title 24 Requirements, Lighting Facts. Exceeds ANSI C78.377A, CE & RoHS Compliant.IP Rating IP67 with appropriately rated accessories

*1 Max Run Length: Dynamic = when the R, G, B channels are not operating at 100% Full Load = when the R, G, B channels are operating at 100%

*2 Max Run Length: Unless otherwise stated, snap and seamless run lengths are the same.


Technical Specifications

5 Year

5Year

160° D:120mm

Physical Specifications

Light Profile Bending Direction

160° Square

Side Bending

21 m

m0.

83 in

ch

11.5 mm0.45 inch

Lumen CountColor Per Foot Per Meter Red >15.24lm >50lm Green >36.58lm >120lm Blue >7.62lm >25lm R+G+B (white) >59.45lm >195lm 2700K >36.58lm >120lm 4000K >36.58lm >120lm

Available ColorsColor CCT WavelengthRed 618-624nmGreen 522-528nmBlue 468-474nmR+G+B N/A2700K 2725 ± 145K4000K 3985 ± 275K

*Color Jackets: For standard or custom color jacket options, contact your Account Manager. Min. order quantity of 656ft (200m).

IP67

Minimum Bending Diameter

4.72 inchΦ 120 mm

Light Emitting Surface

Light Emitting Surface


Part Number Naming Convention

SF-11B-1-01-3W-E-XXX-24DCLED Color (3 digits)

For full part number naming rules, please refer to the document on www.glls.com/support/documentation/

Lead ConnectorFA-11B-1-01-3W-XX-X-XX-XXX-S

Length (3 digits)Exit Type (2 Digits)For Fixture End (1 Digit)Connector Type (2 Digits)

Fixtures

Packaging

Fixture Length White Box Dimensions Packing Box Dimensions # Of White Boxes Package Weight

196.85in (5m) 13.78x1.65x18.11in (35x4.2x46cm) 18.9x14.57x9.54in (48x37x24cm) 5 22.05lbs (10kg)

393.7in (10m) 20.08x1.65x22.05in (45x4.2x56cm) 22.83x18.5x9.45in (58x47x24cm) 5 39.68lbs (18kg)

787.4in (20m) 26.77x1.65x28.34in (61x4.2x72cm) 29.13x25x4.13in (74x63.5x10.5cm) 2 33.07lbs (15kg)

White Box Packing Box

Connectors

www.ledneonflex.comwww.GLLS.com

Seamless Connectors

5

IP67: Rated for wet locations, not submersion. Factory Assembly only.

21.5

mm

2mm11.5mm

21.m

m5

11mm 5mm

21.5

mm

12mm

11.5mm

11.5mm 2mm

14mm

12mm13.5mm

11mm

2m5.

1m

14mm

2mm

11.5mm

12mm

34.

5mm 23.

5mm

11m

m

Seamless Bottom ExitFA-11B-1-01-3W-SE-0-BO-XXX-S

Seamless Side ExitFA-11B-1-01-3W-SE-1-SR-XXX-SFA-11B-1-01-3W-SE-2-SL-XXX-S

Seamless End ExitFA-11B-1-01-3W-SE-0-EN-XXX-S

Seamless End CapFA-11B-1-01-0W-SE-1-EC-000-P FA-11B-1-01-0W-SE-2-EC-000-P

Seamless JumperFA-11B-1-01-3W-SE-0-EJ-XXX-S

21.5

mm

21.5

mm

Connectors


Snap Connectors

IP67: Rated for outdoor use. Factory Assembly or DIY.

27.5mm

46.5mm

19.5 mm

19.5mm

28mm

19.5mm

27.5mm

57mm

28mm

19.5mm

27.5mm

57mm

19.5mm

27.5mm

46.5mm

19.5mm

50.5m m

Snap End ExitNA-11B-1-01-3W-SC-1-EN-XXX-SNA-11B-1-01-3W-SC-2-EN-XXX-S

Snap Side ExitNA-11B-1-01-1-3W-SC-1-SL-XXX-SNA-11B-1-01-1-3W-SC-2-SL-XXX-SNA-11B-1-01-1-3W-SC-1-SR-XXX-SNA-11B-1-01-1-3W-SC-2-SR-XXX-S

Snap Bottom ExitNA-11B-1-01-3W-SC-1-BO-XXX-SNA-11B-1-01-3W-SC-2-BO-XXX-S

Snap End CapNA-11B-1-01-0W-SC-1-ECNA-11B-1-01-0W-SC-2-EC

Connectors


IP20: Rated for indoor use only. Factory Assembly only.

Snap Connectors

50mm

L2

L1

L

Snap JumperNA-11B-1-01-3W-SC-0-EJ-XXX-S

Snap Power T FeedNA-11B-1-01-3W-SC-0-TF-XXX-S

Anvil CutterOptional accessory for on-site cutting.

*Factory order only*

12m m

30m m

Male and FemaleFA-XX-BC-DC-CXX-FFA-XX-BC-DC-CXX-M

FA-XX-BN-XXA-CXX-FFA-XX-BN-XXA-CXX-M

FA-XX-PL-XXA-CXX-FFA-XX-PL-XXA-CXX-M

Optional Accessory:

Anti-Wicking Ferrule

The anti-wicking ferrule is located 115mm (±5mm tolerance) from the connector cable.

For protection against water ingress inside of cable wire hence damage the light.

Mounting Hardware


Standard Anodized Aluminum Channel

Plastic Channel

W x H Standard Length Part Number L1 L2 Screw Hole Φ Hole #

0.54 x 0.87in 1.38in (35mm) CL-11-R-AL-3C5-SD 0.69in (17.5mm) / Φ0.14in (3.5mm) 1

(13.8 x 22mm) 19.69in (500mm) CH-11-R-AL-0M5-SD 1.97in (50mm) 7.87in (200mm) Φ0.14in (3.5mm) 3

39.37in (1000mm) CH-11-R-AL-01M-SD 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 5

78.74in (2000mm) CH-11-R-AL-02M-SD 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 10

W x H Standard Length Part Number L1 L2 Screw Hole Φ Hole #

0.55 x 0.94in 19.69in (500mm) CH-11-R-PL-0M5-SD 1.97in (50mm) 7.87in (200mm) Φ0.14in (3.5mm) 3

(14 x 24mm) 39.37in (1000mm) CH-11-R-PL-01M-SD 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 5

78.74in (2000mm) CH-11-R-PL-02M-SD 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 10

L1 L2

13.8mm

22m

m

Mounting Hardware


Spring Clip Anodized Aluminum Channel

W x H Standard Length Part Number L1 L2 L3 L4 Screw Hole Φ Hole # Clip #

0.64 x 1.01in 1.38in (35mm) CL-11-R-AL-3C5-SP 0.69in (17.5mm) / 0.2in (5mm) 0.98in (25mm) Φ0.14in (3.5mm) 2 1

(16.2 x 25.6mm) 19.69in (500mm) CH-11-R-AL-0M5-SP 0.98in (25mm) 8.86in (225mm) 1.97in (50mm) 7.87in (200mm) Φ0.14in (3.5mm) 3 3

39.37in (1000mm) CH-11-R-AL-01M-SP 0.98in (25mm) 9.35in (237.5mm) 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 5 5

78.74in (2000mm) CH-11-R-AL-02M-SP 0.98in (25mm) 9.6in (243.8mm) 3.94in (100mm) 7.87in (200mm) Φ0.14in (3.5mm) 10 9

25.6

mm

3.5 3.5

L2

L

L4

L1

L3

16.2mm

Stainless Steel Flexible Channel

W x H Standard Length Part Number

0.52 x 0.97in 3.94in (100mm) CH-11-F-SS-0M1-SD

(13.2 x 24.5mm) 11.81in (300mm) CH-11-F-SS-0M3-SD

19.69in (500mm) CH-11-F-SS-0M5-SD

35.43in (900mm) CH-11-F-SS-0M9-SD

10.7mm

0.4mm

13.2mm

24.5

mm

4.76mm

4.76mm

This profile can be mounted using screws in any gaps where the channel bends.


TestingCertifications Testing Organization Certificate Serial N° Report Reference

UL 2108 UL 20160726-E360029 E360029-2013

CE-EMC SGS SZEM1702001259LMV SZEM160600421302

Fixture TestingOptical Testing Spectrum Analysis IES LM 79 (Lumen, CCT, CRI, XY, SDCM, wavelength)

Photometric Distribution IES LM 73 (Lumen intensity distribution & Lux diagram)

Lumen Maintenance & Lifetime IES LM 84 & IES TM28

Temperature Testing Normal Temperature Test UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21

Abnormal Operation Test UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21

Durability Testing Bending Test Manufacturer-defined, 500 cycles

Swing Test UL2388, >750 cycles

Tensile Test Manufacturer-defined, > the weight of light in max. connection length double feed Twist Test Max connection length double feed Manufacturer-defined, >200 cycles

Ball Impact UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21

IK07 IK08 IEC62262

Environmental Testing Chlorinated Water Immersion BG9667, PH6.8-7.6, free chlorine 0.3-0.6mg/L

Salt Water Immersion IEC60598-1, Sailinity 4%

Salt Spray Test IEC68-2-11

Outdoor Exposure Manufacturer-defined

Flame Resistance UL94

UV Exposure ASTMG 154, ISO 4892-3, UVA @ 340nm

IPX5, IPX6, IPX7, IPX8 IEC60529

Temperature Shock Manufacturer-defined, -40°C - 60°C (typical temperature range)

Constant Temperature Manufacturer-defined, 70°C (typical temperature)


TestingCharts

380nm450nm

470nm

480nm

490nm

500nm

510nm

520nm530nm

540nm

550nm

570nm

560nm

580nm

590nm

600nm

620nm650nm770nm

Red

Green

Blue

Wavelength of Color Light

(X ,Y) Chromaticity Diagram

0.28

0.30

0.32

0.34

0.36

0.38

0.40

0.42

0.44

0.46

0.28 0.30 0.32 0.34 0.36 0.38 0.40 0.42 0.44 0.46 0.48 0.50 0.520.26 x

y2700 K

3000 K3500 K

4000 K4500 K

5000 K

5700 K6500 K

2500 K 2200 K

Documents

Table of Contents - GLLS · FA-XX-BN-XXA-CXX-M FA-XX-PL-XXA-CXX-F FA-XX-PL-XXA-CXX-M Optional Accessory: Anti-Wicking Ferrule The anti-wicking ferrule is located 115mm (±5mm tolerance)