Upload
others
View
20
Download
0
Embed Size (px)
Citation preview
Standards / Certifications
ASME A112.18.1-2005/CSA B125.1-05
Warranty ■ Limited Lifetime - to the original end purchaser in consumer installations
■ 5 years - for commercial installations
Finish Options / ModificationsAppend appropriate -suffix to model number
- Polished chrome (standard finish)
Feature Highlights ■ Symmons Shower System with LR style lever handle
■ Symmons Temptrol® pressure-balancing mixing valve with adjustable stop screw to limit temperature adjust handle turn and a lever handle for volume control
■ Showerhead #4-141 single mode with adjustable flood or mist spray
■ Showerhead mounting arm and flange ■ Flow rate 2.5 gpm (9.5 L/min)
Optional lower flow rate restrictor available ■ Polished chrome finish (standard)
Options / ModificationsAppend appropriate -suffix to model number
-X Symmons Temptrol mixing valve includes integral service stops to allow water shut-off for service, p/n S-86-1-BODY-X (Option only applies when ordering model S-2001)
-IPS 1/2 inch female IPS connections on Symmons Temptrol® mixing valve(Not available on valves with integral service stops; option -X)
-REV Reverse coring in valve for back to back installations; hot on right, cold on left,(Only available on valves with integral stops; option -X)
-CHKS Check Stops: Temptrol® mixing valve includes integral check stops.(Only available on valves with integral stops; option -X)
-2.0 2.0 gpm (7.6 L/min) flow rate restrictor
-1.5 1.5 gpm (5.7 L/min) flow rate restrictor
-RB Red blue colored indicators on escutcheon
-D Brass dome cover
-L/HD Showerhead not included, Mounting arm and flange are included
Model Numbers S-2001.................. Shower System with Symmons
Temptrol® mixing valve p/n S-86-1-BODY
S-2001-TRM..........Trim only, valve must be ordered separately
S-86-1-BODY........ Symmons Temptrol® mixing valve without trim
S-86-1-BODY-X.... Symmons Temptrol® mixing valve without trim. Valve includes integral service stops to allow water shut-off for service
Shower System S-2001
Specification Submittal
Symmetrix®
Location:
6-3/8"(162 mm)
4-7/8"(133 mm)
�nished wall
Floor
hot / coldsupply
showerheadsupply
5/8" (16 mm)
6-1/4" dia(159 mm)
2-1/2" dia(64 mm)
tub spoutsupply plug
1/2"-14 NPT
mounting plate p/n T-177
*Note (1)
Temptrolcontrol valve
* Notes:(1) Walls for using T-177 mounting plate (MP)
■ Wall is 1/16" (2 mm) min • 1/2" (13 mm) max■ Fiber or acrylic walls (MP required)■ Plaster or other type walls 1/2" or less (MP optional)■ Protective shield usage (optional)
(2) Dry wall, plaster or other type walls 1/2" or greater■ Protective shield is required; snaps on end of valve spindle...
(3) Dimensions subject to change without notice
Wall cutout hole size3-1/2" (89 mm) min4" (101 mm) min
approx27"
(686 mm)
approx48"
(1219 mm)
Finished wall to rear of valve3-1/2" ± 1/2" (89 mm ±13 mm
Finished wall to pipe centerline2-3/8" ± 1/2" (60 mm ±13 mm)
*See note (2)
ProtectiveShieldp/n T-176
Dimensions Symmetrix Shower System, S-2001
3"(76 mm)
3-¼ ±½" (83 mm)
(±13 mm)
Symmons Industries, Inc. 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667, (781)848-2250 ■ Fax: (800)961-9621, (781)664-1300 ©2011 Symmons Industries, Inc. Printed in U.S.A. ■ www.symmons.com ■ [email protected] ■ 121411