26
1 SVR-1-MPM1 Simplex Repeater Maker for Motorola Mobile Radios Manual Revision: 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This manual supports the following radios: North America: CDM-750, CDM-1250, CDM-1550-LS+ EMEA Region: GM-140, GM-160, GM-340, GM-360, GM-380, GM-640, GM-660, GM-1280 Asia: GM-328, GM-338, GM-338-LS, GM-339, GM-398, GM-399, MCX-720, MCX-760, MCX-780 Latin America: PRO-3100, PRO-5100, PRO-7100, PRO-7200

SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

Embed Size (px)

Citation preview

Page 1: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

1

SVR-1-MPM1

Simplex Repeater Maker for Motorola Mobile Radios

2BManual Revision: 2016-06-16 Rev F

Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher

Covers Hardware Revisions: VS-MPx1: 7701F & Higher

This manual supports the following radios:

North America: CDM-750, CDM-1250, CDM-1550-LS+ EMEA Region: GM-140, GM-160, GM-340, GM-360, GM-380, GM-640, GM-660, GM-1280 Asia: GM-328, GM-338, GM-338-LS, GM-339, GM-398, GM-399, MCX-720, MCX-760, MCX-780 Latin America: PRO-3100, PRO-5100, PRO-7100, PRO-7200

Page 2: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

2

3BSPECIFICATIONS

Operating Voltage 4.75-8.2 VDC Operating Current: Power Save Mode (COR Operation) 2.5 mA typical Repeat Operation 17.5 mA typical Average w/COR Power Save (80-10-10 cycle) <5 mA Average w/COR Power Save (90-5-5 cycle) <4 mA Operating Temperature -30 - +60 C Frequency Response 300-3000 Hz

Input Impedance >45 kΩ Input Level (TX) 0.05-2.5 VPP Input Level (RX) 0.05-2.5 VPP Audio Output Impedance < 1200 Ohm

5BINSTALLATION OVERVIEW

1. Test the radio for functionality. 2. Program the radio per the Radio Programming Section of this manual. 3. Install the unit into the radio per the Hardware Installation Section of this manual. 4. Program the unit per the Product Programming Section of this manual. Note: Midian is not responsible for any damage/loss resulting from the use of Midian’s products.

Page 3: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

3

GENERAL INFORMATION

Midian’s SVR-1 is a simplex repeater maker that can be installed into a mobile or portable radio. The SVR-1 detects COR or VOX from an incoming transmission and records the incoming audio (up to 3 minutes). When the COR or VOX is no longer detected the SVR-1 keys the radio and retransmits the recorded audio. The SVR-1 enables users to create low-cost vehicular repeaters or expand radio coverage into poor coverage areas.

Page 4: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

4

RADIO PROGRAMMING

Motorola CDM-750, CDM-1250, GM-140, GM-160, GM-328, GM-338, GM-398, PRO-3100, PRO-5100, PRO-7100 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable and to hear confirmation beeps from the radio after programming the unit. 1. In the Radio Configuration Window under the Option Board Tab, select Advanced Option Interface as the

Option Board Type. Do not check the Option Board Configuration Download box.

2. When programming the “Conventional Personality”, check the Option Board Feature box for all channels if

using a button to control repeat enable/disable. If doing repeat on a per channel basis, then check Option Board Feature only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

Page 5: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

5

The following step applies to the accessory connector and may be skipped by most users. 3. An accessory pin may be used to control the repeat enable/disable mode. This is useful in remote control

applications. To enable this feature, one of the radio accessory pins must be assigned to Option Board 1 (Input) via the CPS programmer. The MPS also needs to be configured to use this mode input (see page 17).

Page 6: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

6

Motorola GM-339, GM-340, GM-360, GM-380, GM-399, PRO-7200 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable and to hear confirmation beeps from the radio after programming the unit. 1. In the Per Radio Miscellaneous Window under the Global Tab, select “Advanced” as the “Option Board Type”

and set the RX Audio (Accessory Connector) to “Filtered Squelched”. Note: The Accessory Connector is the rear accessory connector, but this setting also affects the audio going to the options connector.

2. For each personality, under the Miscellaneous tab, the “Option Board” must be enabled. Check the Option

Board box for all channels if using a button to control the repeat mode. If doing repeat on a per channel basis, then check Option Board Feature only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

Page 7: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

7

Motorola CDM-1550-LS+, GM-338-LS Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable and to hear confirmation beeps from the radio after programming the unit. Conventional Programming: 1. In the Radio Configuration Window under the Option Board Tab, select Advanced Option Interface as the

Option Board Type. Do not check the Option Board Configuration Download box.

2. When programming the “Conventional Personality”, check the Option Board Feature box for all channels if

using a button to control the repeat mode. If doing repeat on a per channel basis, then check Option Board Feature only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

Page 8: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

8

LTR Programming: 1. In the LS Trunking Personality window, check the Option Board Feature box for each personality. Check the

Option Board Feature box for all channels if using a button to control the repeat mode. If doing repeat on a per channel basis, then check Option Board Feature only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

The following step applies to the accessory connector and may be skipped by most users. 1. An accessory pin may be used to control the repeat enable/disable. This is useful in remote control

applications. To enable this feature, one of the radio accessory pins must be assigned to Option Board 1 (Input) via the CPS programmer. The MPS also needs to be configured to use this mode input (see page 17).

Page 9: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

9

Motorola GM-640, GM-660, GM-1280, MCX-720, MCX-760, MCX-780 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using the Motorola RIB box and cable or RIB-less cable and to hear confirmation beeps from the radio after programming the unit. 1. In the Per Radio Parameters Window set the “Option Board Fitted Mode” as “Advanced”.

2. Edit the ‘MPT Personality’. In the “Options” window, check the “Option Board Enable” box. Check Option

Board Enable for all channels if using a button to control the repeat mode. If doing repeat on a per channel basis, then check Option Board Enable only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

Page 10: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

10

3. If using conventional channels, edit the ‘Conventional Personality Data’. In the “Conventional Personality” window, check the “Option Board Enable” box. Check Option Board Enable for all channels if using a button to control the repeat mode. If doing repeat on a per channel basis, then check Option Board Enable only for repeat enabled channels. Additionally the unit should be programmed to Power Up in Store/Retransmit Mode.

Page 11: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

11

HARDWARE INSTALLATION

Be certain to follow standard anti-static procedures when handling any of Midian’s products. Radio Firmware: For the mobile radios listed, it is necessary to have radio firmware version R05.00.00 or higher. If the radio has an older firmware version, it is necessary to upgrade to the newest firmware. Verifying the firmware version can be done several ways. On most radios, this information is on a label on the bottom of the radio. For display radios, selecting the SoftwareVer# option from the utility menu will report the version. Consult Motorola if you cannot determine the firmware version. Disassembling the Radio: Additional disassembly instructions are also available in Motorola’s Basic Service Manual. 1. Disconnect power. 2. Remove plastic cover from the radio chassis by prying the sides away and lifting up.

3. Remove the 6 retaining bolts from the metal lid using a Torx™ size 20 screwdriver. Carefully begin removing

the lid. If there is already an option board installed such as a voice storage board, disconnect it by gently lifting the latch holding the 40-pin flex cable in place.

4. Remove the lid completely. Unscrew the three bolts holding the option board frame to the lid if one is present. Note: It is not recommended to use the radio for transmitting while disassembled, as some model radios require the lid to be installed for RF power. Installation: 1. Insert the 40-pin flex cable into the 40-pin flex connector on the SVR, making certain it is seated properly,

then close the latch. The silver foil side of the flex should face the edge of the board.

Page 12: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

12

2. The SVR is then mounted into the metal lid of the radio using the option board mounting kit. See pictures below. The mounting kit is ordered from Midian as PRO Option B or from Motorola as RLN4823B. The mounting kit includes the 40-pin flex cable, the mounting frame and 3 mounting screws.

Reassembling the Radio: Additional assembly instructions are also available in Motorola’s Basic Service Manual. 1. Once the unit is installed in the lid, insert the other side of the 40-pin flex cable into the 40-pin flex connector

on the radio’s main board. The shiny side of the flex should face down. 2. Reinstall the metal lid making sure the flex bends toward the back of the radio, otherwise it will be pinched by

the lid. Tighten the screws down in number sequence shown on the lid to 17 in lbs (1.9 NM) torque. Repeat to verify torque is correct after completing the sequence.

3. Snap on plastic cover.

Page 13: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

13

1BPRODUCT PROGRAMMING

Install the MPS programming software if you have not done so already. The unit is programmed through the radio using the Motorola RIB box and cable or RIBless cable and Midian’s MPS programming software. Start the MPS software. From the product selection screen on the MPS software, locate and select the SVR-1-MPP1/MPM1 and click OK. Configure the programming software by selecting File->Preferences and make certain there is a check mark next to ‘Rib Box Enable’ by clicking on it. Also select the appropriate COM port. Set the parameters of the software to fit the application. If any clarifications on a feature are required, move the mouse cursor over the feature name until the question mark appears and right click, an on-line help for that feature will be shown. The MPS always defaults to “Conventional MDC Portable” as the radio type. On the basic settings tab it is necessary to select the proper radio type. After entering the parameters, save the file by going to File - Save As. Enter the file name in the File Name block and click Save. Saving the file will allow for quick and easy reprogramming of units. Turn power on to the radio and then the RIB. Click ProgramUnit! in the MPS software. You will hear 1-3 beeps from the radio if programmed successfully. To read the parameters from the unit, Click on ReadUnit!. The radio and RIB should be powered down for 3 seconds after reading or programming.

Unit Information This information area is updated when a unit is read or programmed. It will also be updated when a data file is loaded from a previous unit read and then saved. Below is a summary of the fields: Product - Shows a more detailed description of the product model within the series. uP #1 Firmware Version - Indicates the reported Firmware Version of the microcontroller of this product. uP #1 Loader Version - Indicates the reported Loader Version of the microcontroller of this product.

Page 14: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

14

Power Up: Enables a short beep sequence that takes place immediately after power-up. Error: This beep will be triggered by any input event which is not programmed. For example, if a long press on the Mode Input is not assigned to a function, it will generate an error beep if a long press is sensed. Mode: When using a switch to enable/disable the SVR, a medium tone followed by a high tone will sound indicating repeat mode is enabled. When pressed again a medium tone followed by a low tone will sound indicating repeat mode is disabled. Go Ahead: Not currently used. Wake Up Beep: Enables a short beep to be sent over the air immediately after PTT is pressed. Enabling this beep is recommended when the 'Wake on VOX' feature is used. This may also be used to get the attention of the party receiving a call. Courtesy Beep: If selected, once the unit is done retransmitting the recorded audio it will generate a courtesy tone to let others know it is done retransmitting. Voice Compression: If checked the SVR-1 can store up to a 3-minute voice message. If unchecked the SVR-1 can store up to a 2.25 minute voice message, but with a higher level of audio quality.

Page 15: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

15

Power Up In Store/Retransmit Mode: If selected the unit will power up in repeat mode. This box must be selected if doing repeat enable on a per-channel basis. Key-Up Delay: This sets the amount of time the unit waits after keying the base station radio before it starts to retransmit the recorded audio. Trunking Delay Enable: Check this box if using a trunking system. This will cause the unit to hold off regenerating the recorded audio until it has received a channel acquisition acknowledgement from the base station radio. If no channel acquisition is received within 6 seconds the SVR-1 will cancel the retransmit cycle. Common PTT: Check this box if PTT In and PTT Out are connected to the same point. PTT Cancels Store/Retransmit: If checked and the PTT is pressed during store/retransmit the unit will not retransmit the incoming transmission. Number of Retransmits: This sets how many times the unit will retransmit the last recorded audio clip. Set to 0 for continuous transmission. Retransmit Interval: This sets the time interval between the retransmits set in the Number of Retransmits field.

Page 16: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

16

Short Press: If using a button for mode select, it can be programmed for Store and Retransmit On, Off or On/Off Toggle. This is a press and immediate release. Long Press: If using a button for mode select, it can be programmed for Store and Retransmit On, Off or On/Off Toggle. This is a press and hold until beeps are heard, then release.

Page 17: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

17

Radio Type: Select from the list the Radio Type that matches your radio. For example if the radio is a CDM-750, GM-140, GM-328 or PRO-5100 you would select Conventional MDC Mobile or if the radio is a GM-339 or GM-660you would select MPT Mobile. Enable Mode LED: Checking this box will cause the green LED on the radio to blink while the repeat mode is enabled while the radio is idle. This blinking may be paused when the radio is receiving or transmitting in order to avoid interfering with normal LED functions of the radio. Enable LCD Messages: Future Use. Use Accessory Pin for Mode Input (mobile only): If desired the unit can be enabled/disabled using an input from the rear accessory connector of the mobile radio. Use Accessory Pin for Emergency Input (mobile only): Future Use.

Please only adjust the parameters of this screen when advised to by Midian.

Page 18: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

18

Beep Volume: Adjust the slider for the desired beep volume. This level is expressed as a percentage of max voice audio level. Over-The-Air-Signal Modulation: Adjust the slider for the desired modulation of tones such as courtesy beep or wake up beeps. This level is expressed as a percentage of max voice audio level.

Playback Level: This controls the audio level when a stored voice message is played back on the radio speaker. If voice playback is too low or too loud, adjust this level accordingly. Transmit Level: This controls the audio level when a stored voice message is retransmitted over the air. If the transmit level is too low or too loud, adjust this level accordingly.

Page 19: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

19

HARDWARE ALIGNMENT

This section describes how to determine and set the audio levels. Midian has already determined the best audio levels for some models of radios. These levels are on the following page in the tables. If you wish to alter the levels please follow the instructions below. Audio Levels Overview:

To ensure the best audio quality, the unit must be configured to match the audio levels used by the radio. The SVR uses programmable gain amplifiers to accomplish this. Determining the gain settings for these amplifiers is an involved process, so Midian simplified this process by developing an algorithm that requires the technician to make only four voltage measurements. From these four measurements, all of the many internal settings are determined. Still, getting the best audio quality will likely require a bit of trial and error. The SVR only has control of audio voltage levels, not input and output impedances. These impedances can dramatically influence the levels. The Four Voltage Measurements:

An oscilloscope and a communications test set/service monitor are required for the measurements. It is recommended that the measurements be recorded in units of mV peak-to-peak. Each measurement must be taken with system modulation at either 60% or 100%, but Midian recommends using 60% These measurements must be taken within 15 seconds of powering on the unit. This is because the unit will enter power saving mode after that time. Measurements made while the unit is in power saving mode will not be valid. TX Alignment Set-Up: A method for controlling transmit modulation is required for accurate measurements in the TX mode. A small speaker held in place near the microphone by a rubber band can serve this purpose in most cases. Use a sine-wave generator to inject a 1000 Hz tone into the speaker. Adjust the output of the sine wave generator so that the transmitter produces 60% of rated modulation while PTT is pressed. Note that if the audio source (such as a speaker) is moved even slightly, the TX modulation may change significantly. Care must be taken to avoid changing the TX modulation while taking the measurements. RX Alignment Set-Up: Using a service monitor send a fully quieting signal (-50 dBm) to the receiver with a 1000 Hz tone at 60% modulation, adjust the volume of the receiver to a comfortable listening level and measure the audio level at the speaker using an AC coupled oscilloscope. Once the volume is adjusted and the measurement taken do not adjust the volume control during the remainder of the alignment. 1. TX Input: The goal of this procedure is to determine the audio level that the unit will see at the TX audio

pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP1 on the unit.

2. RX Input: The goal of this procedure is to determine the audio level that the unit will see at the RX audio

pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP2 on the unit.

3. In the SVR programming software under audio levels set the TX In to the same level as measured in step 1

and for a preliminary adjustment set the TX Out for the same level. Set the RX In to the same level as measured in step 2 and for a preliminary adjustment set the RX Out for the same level. Program the unit.

4. RX Output: The goal of this procedure is to determine the audio level that would normally appear at the RX

audio insertion point in an unmodified radio. Using the same RX Alignment Set-Up procedure verify the audio level at the speaker is still at the same level measured initially in the RX Alignment Set-Up procedure. If not adjust the RX Out level accordingly.

5. TX Output: The goal of this procedure is to determine the audio level that would normally appear at the TX

audio insertion point in an unmodified radio. Using the same TX Alignment Set-Up procedure verify the modulation is still at 60%, if not adjust the TX Out level accordingly.

Page 20: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

20

Programming the Audio Levels:

After determining the audio levels at the audio hookup points, it will be necessary to program the unit to match these levels. In the programming software, there is a slider control on the Audio Levels Screen for each of the of four audio hookup points. Locate the column that corresponds to the modulation and units of measurement for each of the audio hookup points. Adjust the slider bar such that the value appearing in the appropriate column matches what was measured as closely as possible. The following table shows Midian’s recommended levels for the SVR at 60% modulation (mVpp) for tested models of radios:

Motorla Radio Model RX In TX In RX Out TX Out

CDM-750, CDM-1250, GM-140, GM-160, GM-328, GM-338, GM-398, PRO-3100, PRO-5100, PRO-7100

876 216 192 222

GM-340, GM-360, GM-380, GM-339, GM-399, PRO-7200 1044 222 240 216

GM-338-LS, CDM-1550-LS+ 678 138 150 138

GM-640, GM-660, GM-1280, MCX-720, MCX-760, MCX-780

Page 21: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

21

OPERATION

Mode Selection: Mode selection means a method of turning the simplex repeater on and off. In the SVR-1-MPM1 series there are two ways of doing this: Per-Channel Repeat On/Off: To use this feature each channel that is designated as a repeat channel should have the Option Board Feature box enabled in the radio programming software. Channels that are designated as non-repeat should NOT have the Option Board feature box enabled. Additionally the MPS software should be set to Power Up in Store/Retransmit Mode. When using Per-Channel Repeat, a button should NOT be programmed for Mode Select in the MPS software. Repeat On/Off Button: To use this feature each channel should have the Option Board Feature box enabled in the radio programming software. The desired button should be programmed to no function in the radio programming software. In the MPS software on Button Assignment tab set the desired button to “Store/Retransmit On or Off”. Pressing and releasing this button will toggle between repeat enable and disable. A medium tone followed by a high tone indicates the unit is in repeat mode and a medium tone followed by a low tone indicates the unit is in non-repeat mode.

Page 22: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

22

TECHNICAL NOTES

Radio Compatibility: Midian has taken the utmost care to ensure the option board integrates into the radio with minimal impact to the features of the radio. However, some features may not be available in the radio when an option board is used. If a feature is not available, please contact Midian to see if the feature can be added.

Radio Firmware: Midian recommends installing the module into the radio with the existing firmware of the radio provided the firmware is at least R05.00.00. If the radio has a firmware version older than R05.00.00, it must be upgraded. If there are any issues with the firmware then the firmware should be upgraded to the latest. However, it should be noted that occasionally firmware updates may cause a conflict with proper option board/radio communications. This may appear that the SVR is not working properly, but it is a conflict in the serial communication between the option board and radio. Please note that firmware versions between the EMEA region and the Asia and America regions might be different.

Accessory Pin Features: Upon power-up, the radio does not always report the state of the accessory pins to the option board. It may be necessary to toggle the state of these inputs once after power-up to ensure correct operation.

Option Board Feature: Enabling the option board feature tells the radio to report events such as button press, PTT press, carrier detect, etc. to the option board. This feature enables communication between the option board and the radio.

When controlling the SVR with a radio button, it is absolutely required to enable this feature on all channels. For repeat enable/disable on a per channel basis only enable the option board on repeat channels and the power up mode of the unit should be Power Up In Store/Retransmit Mode. On display models, the following icon appears on the LCD when option board mode is on:

MIDIAN CONTACT INFORMATION

MIDIAN ELECTRONICS, INC.

2030 N. Forbes Blvd. #101Tucson, Arizona 85745 USA

Toll-Free: 1-800-MIDIANS Main: 520-884-7981 E-mail: [email protected] U Web: HUwww.midians.com U

Page 23: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

1

1

2

2

3

3

4

4

5

5

6

6

D D

C C

B B

A A

47KR2

+3.3V

560pC1

+3.3V

560pC2

47KR7

47KR6

560pC4

100KR15

100KR14

+3.3VDD.1uC7

2RR49

2RR50

2RR51

+3.3V

+3.3VA

+3.3VDD

8.2KR16

27KR13

.1uC10

.01uC9

4.7KR8

+3.3V

VAN

.0068uC15

.0068uC16 56K

R18

36KR21

.001uC18

75KR19

VAN

1.2MR20

VAN

10KR9.1u

C12

VAN

100pC14

10K1%R11

10K1%R12

10KR10

39pC44

+3.3V+3.3V

.1uC25

.01uC21

560pC19VAN

TP8

TP18

TP7

TP6

TP17

TP5

TP12

TP3

TP4

TP1

TP2

.01uC45

P4:1

P4:2

P4:3

P4:4

P4:5

P4:6

.1uC28

.1uC29

.1uC30

.1uC31

10uC36

10uC35

10uC32

12pC38

100pC39

32 KHzY1

+3.3V

+3.3V

+3.3VDD

+3.3VA

+3.3V

VDDD

4.7KR30

+3.3V

47KR31

+3.3V

VDDD

VDDD

100KR34

100KR35

560pC37

.1uC41

10uC40+3.3V

SW_B+

SRD_SND

SCK_SND

100pC617

VDDD

0RR32

PTT_IN_OUT

4001Q1

4001Q2

*Q6

0RR52

SB1D1

SB1D2

SB1D4

SB1D3

560pC11

0RR57

0RCR58

47KR36 +3.3V

+3.3V .1uC43

SB1D6

.1uC42

RESET

CP

CJS2009-03-25 AWS

2014-26-08

F-1

1 of 2 7701SCHEMATIC

Copyright © 2014

MIDIAN ELECTRONICS, INC.DATE:DESIGN:

UPD BY:REV:

APPR

REV

SHEET PROJECT NUMBER

DOCUMENT NAMEVS SERIES PRO

2.2uC13

SERIES VR2 VR3 U3 U6 U10VS-1200/110/1100 Y Y Y * *

VS-1000VS-1050

SVR-1/VM-3TS-120VAE-1

* * * * ** * * * Y* * * Y ** * * * Y* * * Y Y

* = NOT INSTALLEDY = INSTALLED

R570R0R0R0R0R225

R580R0R0R0R0R

*****

*R1

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206 3.3V

VR1

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206

VR2

IN11

ENA3

GN

D2

RES

4

OUT 5

MIC5206

VR3

.01uC47

.22uC33

0RL1

2.2uC27

2.2uC26

22pC24

3.3KR24

*R17

2.2uC20

*C52

-

+

2

31

411

LMV324U7:1-

+

6

57

LMV324U7:2

-

+

9

108

LMV324

U7:3

-

+

13

1214

LMV324U7:4

3

1

2

4

5 6

U5

7 482 5

16 3

U4

16

13

42

11

9

4

3

37

8

47

28

24

27

20

18

36

43

46

48

45

416

44

1 2 3840 39

34

21

227

35

17

19

29

25

2326

12

10

5

15

14

33323031

49

U1

CS1

SO2

SI5

SCK6

VCC 8

HOLD 7

WP 3

GND 4

AT26DF081AU6

CS7

SO12

SI13

SCK14

DVDD 1

INT29 INT18

GND 2

AVDD 6

GND 5

IADDR0 431011

MMA7455LU10

16

15

33

35

36

37

38

3

11

12

20

46

21

2

39

40

41

42

32 31 13 10 45 1743

30

29

26

27

28

5 14 34 44

1

4

67

8

9

18

19

22

23

24

25

47

48

U3

*C17

*C48

*C51

4.7KR54

4.7KR55

RDY

MISO

TX OUT

RX OUT

EXT MIC

OPT ENA

TX IN

RX IN

DIS IN

PTT_IN_OUT

VDDD

SW_B+

GND

-

+

33

114

52

LM321U12

1KR87

+3.3VA

.01uC85

47pC84

36KR88

120KR89

22KR28

130K1%R3

130K1%R4

.0068uC3

.0068uC6

27KR5

10KR23

10KR22

FLAT TX OUT

VDDD

22pC8

P3

:1

P3:2

P3:3

P3:4

P3:5

TABLE 1R3

CJS CT-1 * * * * *

******

R5 R29*******

Y* 0R

*R29

Y

1

2PROG IN

PROG OUT

P2

225*

+

10uC5

U12Y******

PIC101

PIC102COC1

PIC201

PIC202COC2

PIC301

PIC302COC3

PIC401

PIC402COC4

PIC501

PIC502COC5

PIC601

PIC602COC6

PIC701

PIC702COC7

PIC801

PIC802COC8

PIC901 PIC902

COC9

PIC1001

PIC1002COC10

PIC1101 PIC1102

COC11

PIC1201 PIC1202

COC12

PIC1301

PIC1302COC13

PIC1401

PIC1402COC14

PIC1501 PIC1502

COC15

PIC1601 PIC1602

COC16

PIC1701 PIC1702

COC17

PIC1801PIC1802

COC18

PIC1901

PIC1902COC19 PIC2001

PIC2002COC20

PIC2101 PIC2102

COC21

PIC2401

PIC2402COC24

PIC2501 PIC2502

COC25

PIC2601

PIC2602COC26PIC2701

PIC2702COC27

PIC2801 PIC2802

COC28

PIC2901 PIC2902

COC29

PIC3001 PIC3002

COC30

PIC3101

PIC3102COC31 PIC3201

PIC3202COC32

PIC3301 PIC3302

COC33

PIC3501 PIC3502

COC35

PIC3601 PIC3602

COC36

PIC3701

PIC3702COC37

PIC3801

PIC3802COC38

PIC3901

PIC3902COC39

PIC4001 PIC4002

COC40

PIC4101 PIC4102

COC41

PIC4201 PIC4202

COC42

PIC4301 PIC4302

COC43

PIC4401

PIC4402COC44

PIC4501

PIC4502COC45

PIC4701 PIC4702

COC47

PIC4801 PIC4802

COC48

PIC5101

PIC5102COC51 PIC5201

PIC5202COC52

PIC8401

PIC8402COC84

PIC8501

PIC8502COC85

PIC61701

PIC61702COC617

PICR5801 PICR5802

COCR58

PID101PID102

COD1

PID201PID202

COD2

PID301PID302

COD3

PID401PID402

COD4

PID601PID602

COD6

PIL101

PIL102

COL1

PIP201

PIP202

COP2

PIP301

COP3:1PIP302

COP3:2PIP303

COP3:3PIP304

COP3:4PIP305

COP3:5

PIP401 COP4:1

PIP402 COP4:2

PIP403 COP4:3

PIP404 COP4:4

PIP405 COP4:5

PIP406 COP4:6

PIQ10DPIQ10G

PIQ10S

COQ1

PIQ20DPIQ20G

PIQ20S

COQ2

PIQ60DPIQ60G

PIQ60S

COQ6

PIR101 PIR102

COR1

PIR201 PIR202

COR2

PIR301 PIR302

COR3

PIR401 PIR402

COR4

PIR501 PIR502

COR5

PIR601 PIR602

COR6

PIR701 PIR702

COR7

PIR801 PIR802

COR8

PIR901 PIR902

COR9 PIR1001 PIR1002

COR10

PIR1101 PIR1102

COR11 PIR1201 PIR1202

COR12

PIR1301

PIR1302

COR13

PIR1401

PIR1402

COR14

PIR1501

PIR1502

COR15 PIR1601

PIR1602

COR16

PIR1701 PIR1702

COR17

PIR1801 PIR1802

COR18PIR1901 PIR1902

COR19

PIR2001 PIR2002

COR20

PIR2101 PIR2102

COR21

PIR2201

PIR2202

COR22

PIR2301

PIR2302

COR23PIR2401 PIR2402

COR24

PIR2801 PIR2802

COR28

PIR2901 PIR2902

COR29

PIR3001

PIR3002

COR30

PIR3101

PIR3102

COR31

PIR3201 PIR3202

COR32

PIR3401 PIR3402

COR34

PIR3501 PIR3502

COR35

PIR3601 PIR3602

COR36

PIR4901 PIR4902

COR49

PIR5001 PIR5002

COR50

PIR5101 PIR5102

COR51

PIR5201 PIR5202

COR52

PIR5401 PIR5402

COR54

PIR5501 PIR5502

COR55

PIR5701 PIR5702

COR57

PIR8701

PIR8702

COR87PIR8801 PIR8802

COR88

PIR8901 PIR8902

COR89

COtb0sch1

PITP101

COTP1

PITP201

COTP2

PITP301

COTP3

PITP401

COTP4

PITP501

COTP5

PITP601

COTP6

PITP701

COTP7

PITP801

COTP8

PITP1201

COTP12

PITP1701

COTP17

PITP1801

COTP18

COTxt1

PIU101 PIU102

PIU103

PIU104

PIU105

PIU106

PIU107

PIU108

PIU109

PIU1010

PIU1011

PIU1012

PIU1013

PIU1014

PIU1015

PIU1016

PIU1017

PIU1018

PIU1019

PIU1020

PIU1021

PIU1022

PIU1023

PIU1024

PIU1025

PIU1026

PIU1027

PIU1028

PIU1029

PIU1030

PIU1031

PIU1032

PIU1033

PIU1034

PIU1035

PIU1036

PIU1037

PIU1038PIU1039PIU1040

PIU1041

PIU1042

PIU1043

PIU1044

PIU1045

PIU1046

PIU1047

PIU1048

PIU1049

COU1

PIU301

PIU302

PIU303

PIU304

PIU305

PIU306

PIU307

PIU308

PIU309

PIU3010

PIU3011

PIU3012

PIU3013

PIU3014

PIU3015

PIU3016

PIU3017PIU3018

PIU3019

PIU3020

PIU3021

PIU3022

PIU3023

PIU3024

PIU3025

PIU3026

PIU3027

PIU3028

PIU3029

PIU3030

PIU3031PIU3032

PIU3033 PIU3034

PIU3035

PIU3036

PIU3037

PIU3038

PIU3039

PIU3040

PIU3041

PIU3042

PIU3043

PIU3044

PIU3045

PIU3046

PIU3047

PIU3048

COU3

PIU401

PIU402

PIU403

PIU404

PIU405

PIU406

PIU407PIU408

COU4

PIU501

PIU502

PIU503

PIU504

PIU505 PIU506

COU5

PIU601

PIU602

PIU603

PIU604

PIU605

PIU606

PIU607

PIU608

COU6

PIU701

PIU702

PIU703PIU704

PIU7011COU7:1

PIU705

PIU706

PIU707COU7:2

PIU708

PIU709

PIU7010

COU7:3

PIU7012

PIU7013

PIU7014COU7:4

PIU1001

PIU1002

PIU1003

PIU1004

PIU1005

PIU1006

PIU1007

PIU1008

PIU1009

PIU10010

PIU10011

PIU10012

PIU10013

PIU10014

COU10

PIU1201

PIU1202

PIU1203

PIU1204

PIU1205COU12

PIVR101

PIVR102

PIVR103

PIVR104

PIVR105

COVR1

PIVR201

PIVR202

PIVR203

PIVR204

PIVR205

COVR2

PIVR301

PIVR302

PIVR303

PIVR304

PIVR305

COVR3

PIY101

PIY102COY1

Page 24: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

1

1

2

2

3

3

4

4

5

5

6

6

D D

C C

B B

A A

100KR633

100KR646

100KR632

100KR648

100pC616

VDDD SW_B+

1KR620

1KR621

1KR622

1KR618

1KR619

1KR623

GRND601

GRND602

GRND603

GRND604

GRND605

GRND606

__

B4

\|/

B5

+

B6

P1

B7

P2

B8

P3

B9

1

B10

2

B11

3

B12

4

B13

5

B14

6

B15

7

B16

8

B17

9

B18

*

B19

0

B20

#

B21

ROW_3 ROW_4 ROW_5

COL_5

COL_1 COL_2 COL_3

ROW_5

ROW_4

ROW_3

ROW_2

ROW_1

51.1K1%R601

51.1K1%R602

13K1%R603

13K1%R607

22.1K1%R604

22.1K1%R608

43.2K1%R605

43.2K1%R609

130K1%R606

130K1%R610

51.1K1%R611

VDDD

VDDD

COL_1 COL_2 COL_3 COL_4 COL_5

ROW_1 ROW_2 ROW_3 ROW_5ROW_4

VDDD

47KR649

3.3KR647

SRD_SND

100pC610

SW_B+

100pC612

100pC611

VDDD

VDDD

100pC615

NOTE: * = NOT INSTALLED

D

A

C

D

B

A

61 2 3 4 5

1 2 3 4 5 6

CP

CJS2009-03-25 AWS

2014-26-08

F-1

2 of 2 7701SCHEMATIC

Copyright © 2014

MIDIAN ELECTRONICS, INC.DATE:DESIGN:

UPD BY:REV:

APPR

REV

SHEET PROJECT NUMBER

DOCUMENT NAMEVS SERIES PRO

B25Q602

Y25Q601

B25Q603

560K1%R612

1MR613

*C609

-

+

4

31

25

LMC7211U602

LED ENABLE

LED BKLT ENA

KEY INTRP

100pC613

RESET

* = NOT INSTALLEDY = INSTALLED

D6MPP1

D601 to D606

MPM1 Y* Y

*

J602Y

*

U602Y

*

TABLE 2

( aka KEY_ROW )

( aka KEY COL )

PIB401 PIB402 PIB403COB4

PIB501 PIB502 PIB503COB5

PIB601 PIB602 PIB603COB6

PIB701 PIB702 PIB703COB7

PIB801 PIB802 PIB803COB8

PIB901 PIB902 PIB903COB9

PIB1001 PIB1002 PIB1003COB10

PIB1101 PIB1102 PIB1103COB11

PIB1201 PIB1202 PIB1203COB12

PIB1301 PIB1302 PIB1303COB13

PIB1401 PIB1402 PIB1403COB14

PIB1501 PIB1502 PIB1503COB15

PIB1601 PIB1602 PIB1603COB16

PIB1701 PIB1702 PIB1703COB17

PIB1801 PIB1802 PIB1803COB18

PIB1901 PIB1902 PIB1903COB19

PIB2001 PIB2002 PIB2003COB20

PIB2101 PIB2102 PIB2103COB21

PIC60901 PIC60902

COC609

PIC61001

PIC61002COC610

PIC61101

PIC61102COC611

PIC61201

PIC61202COC612

PIC61301

PIC61302COC613

PIC61501

PIC61502COC615

PIC61601

PIC61602COC616

PID60101

PID60102

COD601

PID60201

PID60202

COD602

PID60301

PID60302

COD603

PID60401

PID60402

COD604

PID60501

PID60502

COD605

PID60601

PID60602

COD606

PIQ6010B

PIQ6010C PIQ6010E

COQ601

PIQ6020B

PIQ6020C

PIQ6020E

COQ602

PIQ6030B

PIQ6030C

PIQ6030E

COQ603

PIR60101

PIR60102

COR601

PIR60201

PIR60202

COR602

PIR60301 PIR60302

COR603

PIR60401 PIR60402

COR604

PIR60501 PIR60502

COR605

PIR60601 PIR60602

COR606

PIR60701 PIR60702

COR607

PIR60801 PIR60802

COR608

PIR60901 PIR60902

COR609

PIR61001 PIR61002

COR610

PIR61101

PIR61102

COR611

PIR61201

PIR61202

COR612

PIR61301 PIR61302

COR613

PIR61801

PIR61802

COR618

PIR61901

PIR61902

COR619

PIR62001

PIR62002

COR620

PIR62101

PIR62102

COR621

PIR62201

PIR62202

COR622

PIR62301

PIR62302

COR623

PIR63201

PIR63202

COR632

PIR63301

PIR63302

COR633

PIR64601

PIR64602

COR646

PIR64701 PIR64702

COR647

PIR64801

PIR64802

COR648

PIR64901 PIR64902

COR649

COtb0sch2

PIU60201

PIU60202

PIU60203

PIU60204

PIU60205

COU602

Page 25: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

PAC101PAC102COC1

PAC201PAC202COC2

PAC302PAC301COC3

PAC401PAC402COC4

PAC501

PAC502COC5

PAC602

PAC601

COC6

PAC701

PAC702

COC7

PAC802

PAC801

COC8

PAC901

PAC902

COC9

PAC1001PAC1002COC10

PAC1101 PAC1102COC11

PAC1201

PAC1202COC12

PAC1301 PAC1302COC13

PAC1401

PAC1402COC14

PAC1501

PAC1502

COC15PAC1601

PAC1602

COC16 PAC1701PAC1702COC17

PAC1801PAC1802COC18

PAC1901PAC1902COC19

PAC2001PAC2002COC20

PAC2101 PAC2102COC21

PAC2401

PAC2402COC24

PAC2501 PAC2502COC25

PAC2601 PAC2602COC26

PAC2701 PAC2702COC27

PAC2801PAC2802COC28

PAC2901PAC2902COC29

PAC3001PAC3002COC30

PAC3101

PAC3102

COC31 PAC3201

PAC3202

COC32

PAC3301

PAC3302COC33PAC3501

PAC3502COC35PAC3601

PAC3602COC36

PAC3701

PAC3702COC37

PAC3801

PAC3802

COC38PAC3901

PAC3902

COC39

PAC4001 PAC4002COC40

PAC4101PAC4102COC41

PAC4201 PAC4202COC42

PAC4301

PAC4302COC43

PAC4401PAC4402COC44

PAC4501

PAC4502

COC45

PAC4701

PAC4702

COC47

PAC4801PAC4802COC48

PAC5101

PAC5102COC51

PAC5201

PAC5202COC52

PAC8402

PAC8401

COC84PAC8502

PAC8501COC85

PAC60901

PAC60902COC609 PAC61001

PAC61002COC610

PAC61101

PAC61102COC611PAC61201

PAC61202

COC612

PAC61301PAC61302COC613

PAC61501

PAC61502

COC615PAC61601PAC61602COC616

PAC61701

PAC61702COC617

PACR5801 PACR5802COCR58

PAD101

PAD102

COD1

PAD201 PAD202COD2

PAD301

PAD302

COD3

PAD401 PAD402COD4

PAD601PAD602 COD6

PAJ601013

PAJ60106

PAJ601019

PAJ60101PAJ60102

PAJ60103PAJ60104

PAJ60105

PAJ60107PAJ60108

PAJ60109PAJ601010

PAJ601011PAJ601012

PAJ601014PAJ601015

PAJ601016PAJ601017

PAJ601018

PAJ601020PAJ601021

PAJ601022PAJ601023

PAJ601024PAJ601025

PAJ601026PAJ601027

PAJ601028PAJ601029

PAJ601030PAJ601031

PAJ601032PAJ601033

PAJ601034PAJ601035

PAJ601036PAJ601037

PAJ601038PAJ601039

PAJ601040

PAJ6010APAJ6010B

PAJ6010CPAJ6010DCOJ601

PAJ602018

PAJ602017

PAJ602016

PAJ602015

PAJ602014

PAJ602013

PAJ602012

PAJ602011

PAJ602010

PAJ60209

PAJ60208

PAJ60207

PAJ60206

PAJ60205

PAJ60204

PAJ60203

PAJ60202

PAJ60201

PAJ6020B

PAJ6020A

COJ602

PAL101

PAL102

COL1

PAP201PAP202 COP2 PAP304 PAP303PAP305 PAP302 PAP301COP3

PAP404PAP406 PAP403PAP405 PAP402 PAP401COP4

PAQ10SPAQ10D

PAQ10GCOQ1

PAQ20SPAQ20D

PAQ20G

COQ2

PAQ60SPAQ60D

PAQ60GCOQ6

PAQ6010BPAQ6010C

PAQ6010ECOQ601

PAQ6020BPAQ6020C

PAQ6020ECOQ602

PAQ6030BPAQ6030C

PAQ6030ECOQ603

PAR101

PAR102

COR1

PAR201

PAR202COR2

PAR302

PAR301COR3

PAR402PAR401COR4

PAR502PAR501COR5

PAR601

PAR602COR6

PAR701

PAR702COR7

PAR801 PAR802COR8

PAR901

PAR902COR9

PAR1001

PAR1002COR10PAR1101PAR1102COR11

PAR1201 PAR1202COR12

PAR1301

PAR1302

COR13

PAR1401 PAR1402COR14

PAR1501

PAR1502COR15

PAR1601

PAR1602

COR16

PAR1701 PAR1702COR17

PAR1801PAR1802COR18

PAR1901 PAR1902COR19 PAR2001

PAR2002

COR20PAR2101 PAR2102COR21 PAR2202

PAR2201COR22PAR2302PAR2301COR23

PAR2401PAR2402COR24

PAR2802

PAR2801

COR28

PAR2902PAR2901COR29

PAR3001

PAR3002

COR30 PAR3101 PAR3102COR31

PAR3201PAR3202COR32

PAR3401

PAR3402COR34

PAR3501

PAR3502COR35

PAR3601 PAR3602COR36

PAR4901

PAR4902

COR49

PAR5001PAR5002COR50

PAR5101

PAR5102

COR51

PAR5201PAR5202COR52

PAR5401PAR5402COR54

PAR5501PAR5502COR55

PAR5701 PAR5702COR57

PAR8702 PAR8701COR87

PAR8802

PAR8801COR88PAR8902

PAR8901

COR89

PAR60101 PAR60102COR601

PAR60201

PAR60202

COR602PAR60301 PAR60302COR603

PAR60401PAR60402COR604

PAR60501 PAR60502COR605

PAR60601PAR60602COR606

PAR60701 PAR60702COR607

PAR60801PAR60802COR608

PAR60901 PAR60902COR609

PAR61001PAR61002COR610

PAR61101PAR61102COR611

PAR61201

PAR61202COR612PAR61301

PAR61302COR613

PAR61801

PAR61802COR618

PAR61901 PAR61902COR619

PAR62001PAR62002COR620

PAR62101PAR62102COR621

PAR62201 PAR62202COR622

PAR62301

PAR62302COR623

PAR62501 PAR62502COR625

PAR62901

PAR62902COR629

PAR63001

PAR63002COR630

PAR63101PAR63102COR631

PAR63201

PAR63202

COR632

PAR63301PAR63302COR633

PAR63801PAR63802COR638

PAR64601PAR64602COR646

PAR64701PAR64702COR647

PAR64801PAR64802COR648

PAR64901PAR64902COR649

COtb0sch1

PATP101 COTP1

PATP201 COTP2

PATP301COTP3

PATP401COTP4

PATP501COTP5

PATP601COTP6

PATP701

COTP7

PATP801 COTP8

PATP1201

COTP12

PATP1701COTP17

PATP1801

COTP18

PAU101PAU102

PAU103PAU104

PAU105PAU106

PAU107PAU108

PAU109PAU1010PAU1011

PAU1012

PAU1013PAU1014

PAU1015PAU1016

PAU1017PAU1018

PAU1019PAU1020

PAU1021PAU1022PAU1023

PAU1024 PAU1025PAU1026

PAU1027PAU1028

PAU1029PAU1030

PAU1031PAU1032

PAU1033PAU1034

PAU1035PAU1036

PAU1037PAU1038

PAU1039PAU1040PAU1041

PAU1042PAU1043

PAU1044PAU1045

PAU1046PAU1047

PAU1048

PAU1049COU1

PAU3048PAU3047PAU3046PAU3045PAU3044PAU3043PAU3042PAU3041PAU3040PAU3039PAU3038PAU3037PAU3036

PAU3035

PAU3034

PAU3033

PAU3032

PAU3031

PAU3030

PAU3029

PAU3028

PAU3027

PAU3026

PAU3025

PAU3024 PAU3023 PAU3022 PAU3021 PAU3020 PAU3019 PAU3018 PAU3017 PAU3016 PAU3015 PAU3014 PAU3013PAU3012

PAU3011

PAU3010

PAU309

PAU308

PAU307

PAU306

PAU305

PAU304

PAU303

PAU302

PAU301

COU3

PAU401

PAU402

PAU403

PAU404 PAU405

PAU406

PAU407

PAU408

COU4 PAU506

PAU505

PAU504PAU503

PAU502

PAU501

COU5

PAU601

PAU602

PAU603

PAU604 PAU605

PAU606

PAU607

PAU608

COU6

PAU7014

PAU7013

PAU7012

PAU7011

PAU7010

PAU709

PAU708PAU707

PAU706

PAU705

PAU704

PAU703

PAU702

PAU701

COU7

PAU10014PAU10013PAU10012PAU10011PAU10010PAU1009PAU1008 PAU1007 PAU1006

PAU1005PAU1004PAU1003PAU1002PAU1001

COU10PAU1204

PAU1203 PAU1202

PAU1205

PAU1201

COU12

PAU60203

PAU60201

PAU60204

PAU60202

PAU60205COU602

PAVO102 PAVO101

PAVO10E

PAVO10CPAVO10B

PAVO103

PAVO104

PAVO105

PAVO106

PAVO107

PAVO108

PAVO109

PAVO1010

PAVO1011

PAVO1012

PAVO1013PAVO1014PAVO1015PAVO1016PAVO1017PAVO1018PAVO1019PAVO1020PAVO1021PAVO1022PAVO1023PAVO1024PAVO1025

PAVO1026

PAVO1027

PAVO1028

PAVO1029

PAVO1030

PAVO1031

PAVO1032

PAVO1033

PAVO1034

PAVO1035

PAVO1036

PAVO1037 PAVO1038 PAVO1039 PAVO1040 PAVO1041 PAVO1042 PAVO1043 PAVO1044 PAVO1045 PAVO1046 PAVO1047 PAVO1048

PAVO10A

PAVO1049

PAVO10GPAVO10D

PAVO10S

COVO1

PAVR103

PAVR101

PAVR104

PAVR102

PAVR105

COVR1

PAVR203 PAVR201

PAVR204

PAVR202

PAVR205COVR2

PAVR303PAVR301

PAVR304

PAVR302

PAVR305

COVR3

PAY101PAY102COY1

Page 26: SVR1MPM1-2016-06-16 Rev F - Midian Electronics · ... 2016-06-16 Rev F Covers Firmware Revisions: VS-1xx: 1.62.00 and Higher Covers Hardware Revisions: VS-MPx1: 7701F & Higher This

PAB401

PAB402

PAB403

COB4

PAB501

PAB502

PAB503

COB5

PAB601

PAB602

PAB603

COB6

PAB701

PAB702

PAB703

COB7

PAB801

PAB802

PAB803

COB8

PAB901

PAB902

PAB903

COB9

PAB1001

PAB1002

PAB1003

COB10

PAB1101

PAB1102

PAB1103

COB11

PAB1201

PAB1202

PAB1203

COB12

PAB1301

PAB1302

PAB1303

COB13

PAB1401

PAB1402

PAB1403

COB14

PAB1501

PAB1502

PAB1503

COB15

PAB1601

PAB1602

PAB1603

COB16

PAB1701

PAB1702

PAB1703

COB17

PAB1801

PAB1802

PAB1803

COB18

PAB1901

PAB1902

PAB1903

COB19

PAB2001

PAB2002

PAB2003

COB20

PAB2101

PAB2102

PAB2103

COB21

PAD60102 PAD60101 COD601

PAD60201PAD60202 COD602

PAD60302PAD60301 COD603

PAD60401 PAD60402COD604

PAD60502PAD60501 COD605

PAD60601 PAD60602COD606

COtb0sch2

COVO4