54
Rules for Classification and Construction I Ship Technology 1 Seagoing Ships 20 Stowage and Lashing of Containers Edition 2012

Stowage and Lashing of Containers

Embed Size (px)

Citation preview

Page 1: Stowage and Lashing of Containers

Rules for Classification and Construction I Ship Technology

1 Seagoing Ships

20 Stowage and Lashing of Containers

Edition 2012

Page 2: Stowage and Lashing of Containers

The following Rules come into force on 1 May 2012.

Alterations to the preceding Edition are marked by beams at the text margin.

Germanischer Lloyd SE

Head Office Brooktorkai 18, 20457 Hamburg, Germany

Phone: +49 40 36149-0 Fax: +49 40 36149-200

[email protected]

www.gl-group.com

"General Terms and Conditions" of the respective latest edition will be applicable (see Rules for Classification and Construction, I - Ship Technology, Part 0 - Classification and Surveys).

Reproduction by printing or photostatic means is only permissible with the consent of Germanischer Lloyd SE.

Published by: Germanischer Lloyd SE, Hamburg

Page 3: Stowage and Lashing of Containers

Table of Contents

Section 1 Explanations

A. Explanations ............................................................................................................................... 1- 1

Section 2 Rules for the Arrangement and Construction

A. Stowage of Containers on the Weather Deck (incl. hatchways) ................................................. 2- 1 B. Below-Deck Stowage of Containers ........................................................................................... 2- 3

Section 3 Design Principles

A. Calculation of the Lashing and Shoring Forces .......................................................................... 3- 1 B. Design of the Cell Guide Structures ........................................................................................... 3- 9

Section 4 Materials, Welding and Tests

A. Materials and Constructional Parts ............................................................................................. 4- 1 B. Welding ...................................................................................................................................... 4- 3

Annex A Instruction for the Performance of Inspections of Container Lashing Elements A. Performance of Inspections ........................................................................................................ A- 1

Annex B Welding Procedure Qualification Test Flash Butt Welding or Friction Welding of Container Lashing Elements

A. Procedure Qualification Flash Butt Welding .............................................................................. B- 1

Annex C Container Lashing Fittings

A. Loads for Container Stowage- and Lashing Fittings .................................................................. C- 1 B. Operational Tests for Fully Automatic Locks ............................................................................ C- 2

Annex D Approvals of Computer Software for Determination of Forces in the Lashing System

A. Approval of Lashing Computers/Software ................................................................................. D- 1

Annex E Weights, Measurements and Tolerances

Annex F Container-Dimensions

Annex G Code of Container Position

Annex H Height Tolerances of Container Foundations

Annex I Maximum Allowable Forces on ISO-Container

Annex J Determination of the Existing Stack Weight for Mixed Stowage (20' and 40' Container) for the Individual Foundation Points

I - Part 1 GL 2012

Table of Contents Chapter 20Page 3

Page 4: Stowage and Lashing of Containers
Page 5: Stowage and Lashing of Containers

Section 1

Explanations

A. Explanations

1. Application of the Rules 1

1.1 Ships classed with Germanischer Lloyd

1.1.1 Those parts of the container stowage and lashing equipment which are connected to the ship's hull by welding or which may affect its strength are subject to approval within the scope of the Rules for the Classification and Construction of Seagoing Steel Ships (testing of materials, examination of drawings, survey during construction).

The parts mentioned are to be dimensioned in such a way that they do not endanger safety and operation.

Connections of these parts to the hull and their sub-structures are subject to approval too, and shall be dimensioned according to the loads given in Section 3. Corresponding drawings and material properties are to be submitted. The locations of the connections shall be indicated in the documents for approval according to the GL Rules for Hull Structures (I-1-1).

1.1.2 In respect of other elements of the stowage and lashing equipment such as loose lashing elements and removable guide structures, the respective docu-mentation (drawings, calculations) will be examined in connection with the examination of the entire lash-ing system. These parts shall be fabricated in confor-mity with the provisions laid down in Section 4 and subjected to strength tests according to Annex B.

1.1.3 The validity of the characters of classification and additional notations according to 1.1.4 depends on the exclusive use of container lashing and stowing gear approved and tested by GL in accordance with Section 4 and Annex A of these Rules, and on the approval of the Containerstowage- and -lashingplan.

–––––––––––––– 1 For ships under the supervision of See-Berufsgenossenschaft,

they require approval of equipment for regular transport of containers. See also Accident Prevention Regulations (UVV See) of See-Berufsgenossenschaft, issued at 1.1.1981, § 45, in-structions to item (3), b, c and m. Furthermore, the ship's sta-bility is to be checked with regard to wind in case of containers transported on deck (Publication of application of stability rules for general cargo ships, passenger ships and special ships, issued 26th of Oct., 1984, page 11 - number 3.2.8 and 3.2.9). Furthermore the "publication of the guidelines of safe practice for cargo stowage and securing aboard seagoing ves-sels" are to be observed. Special requirements of stowage and lashing of containers aboard ships of the flag state concerned are to be considered.

Certificates of the container fittings of the ship shall be included in ship’s documents on board. The Con-tainerstowage- and -lashingplan has to contain a schedule with the following specification of the Con-tainerstowage- and -lashing equipment:

– Number of parts with position no.

– Designation (type)

– Manufacturer

– Breaking load and working load.

In the Class Certificate of the ship a notation will be entered to this effect.

The manufacturer of the approved stowage and lash-ing system has to ensure, that clear instructions for the danger free and safe operation of all components of the system are available to the Ship's command.

The responsibility for retaining this condition rests with the owner of the ship.

The Surveyors of Germanischer Lloyd will satisfy themselves during the periodical class surveys that the conditions for granting the class notation are still met.

1.1.4 Classification symbols and notations

Ships which are intended to exclusively carry contain-ers and which are fitted with the respective equipment complying with the requirements of the GL Rules for Hull Structures (I-1-1), Section 21, G. will be as-signed, in addition to their Characters of Classifica-tion, the Notation CONTAINER SHIP.

Ships, which are intended to carry containers only occasionally or as partial cargo and which are fitted with the respective equipment complying with the requirements of Section 21, G. will be assigned, in addition to their Characters of Classification, the No-tation EQUIPPED FOR CARRIAGE OF CONTAINERS (see GL Rules for Classification and Surveys (I-0), Section 2, Table 2.6).

1.1.5 A stowage and lashing plan stamped by GL is to be kept on board and made available to the Sur-veyor of GL on request. A container stowage and lashing plan is also to be kept on board, in case a lash-ing computer is installed.

1.1.6 In case of a conversion or removal of the container equipment, the GL Head Office shall be informed accordingly.

Owners and/or the conversion yard will have to sub-mit the relevant drawings for approval.

I - Part 1 GL 2012

Section 1 Explanations Chapter 20Page 1–1

A

Page 6: Stowage and Lashing of Containers

This refers also to modifications of the stowage ar-rangement due to an increase in the number of con-tainer stowage places on the weather deck and the weather deck hatch covers; including, for instance, the arrangement of additional container layers, an increase of stack loads or modification of the container weights in the individual layers.

1.2 The compliance with the present Rules may be certified by GL for ships other than covered by 1.1, subsequent to an adequate examination of the respec-tive documentation.

1.3 Type approval

GL grants type approval of stowage and lashing ele-ments, removable or to be permanently built in and fabricated in series; the approval procedure may con-sist of examinations of drawings and load tests and serves as a basis for individual approval in connection with the assignment of class (1.1.2).

If the load test shows satisfactory results, a Type Cer-tificate will be issued.

Note

Where container stowage and lashing elements are intended to be used as loose gear - e.g. lifting pots, lifting foundations on the hatch covers – the Guide-lines for the Construction and Survey of Lifting Appli-ances", are to be applied.

1.4 Lashing computers

If a computer for determination of forces in the lash-ing system used on board, the approval of soft- and hardware by GL is recommended. For particulars see Annex D.

2. Stowage of containers

2.1 General

All equipment on deck and in the holds essential for maintaining the safety of the ship and which are to be accessible at sea, e.g. fire fighting equipment, sound-ing pipes etc., should not be made inaccessible by containers or their stowing and lashing equipment.

Note Containers stowed on weather deck on ships, which are under supervision of the See-Berufsgenossen-schaft, aside of the hatches an operational walkway of at least 600 mm width and 2000 mm height shall re-main. The deck shall be free from any edges which can cause stumbling.

Under specific conditions the operational walkways can also be permitted below deck.

2.2 For transmitting the forces from the container stowing and lashing equipment into the ship's hull adequate welding connections and local reinforce-ments of structural members are to be provided.

2.3 The hatchway coamings are to be dimen-sioned according to the loads appearing in way of the connections of transverse and longitudinal struts of cell guide systems.

The cell guide systems are not permitted to be con-nected to projecting deck plating edges in way of the hatchways. Any flame cutting or welding should be avoided, particularly at the deck roundings in the hatchway corners.

2.4 Where inner bottom, decks, or hatchcovers are loaded with containers, adequate substructures, e.g. carlings, half height girders etc., are to be pro-vided. The plate thickness is to be increased where required. For welded-in parts, see the GL Rules for Hull Structures (I-1-1), Section 19, B.2. Container foundation and other substructures are to be deter-mined according to GL Rules for Hull Structures (I-1-1), Section 21, G.

2.5 The Rules base on the stowage of containers that correspond in all aspects to the actual ISO Stan-dard. Deviations require special examination and approval of the Germanischer Lloyd.

As gross weights of the containers the following weights may be assumed:

20’ minimum 2,5 tons

maximum 30,5 tons

40’ minimum 3,5 tons

maximum 30,5 tons

45’ minimum 4,5 tons

maximum 32,5 tons

Other container sizes correspondingly.

2.6 All stowage and lashing fittings (loose or fixed) shall be certified. Corresponding certificates are to be included into documentation on board.

3. Cargo securing manual

According to IMO requirement all ships subject to SOLAS have to be equipped with an approved cargo securing manual from 31.12.97. Exempted are ships for liquid cargo, bulk cargo respect fishing vessel and offshore units.

The certification of the manuals can be done by GL.

Chapter 20 Page 1–2

Section 1 Explanations I - Part 1GL 2012

A

Page 7: Stowage and Lashing of Containers

Section 2

Rules for the Arrangement and Construction

A. Stowage of Containers on the Weather Deck (incl. hatchways)

1. Seating conditions

A check shall be made whether the seating points of the containers on the ship's deck can shift relatively to one another with the ship at sea. This may be the case, for instance, aboard ships having very large hatch openings where the container rests partly on the hatch cover and partly on supports beside the hatchway. Relative dislocations of container seating points shall also be taken into account where the container is seated on two hatches of a twin-hatch ship.

Where necessary, the alignment steps (cones) at the points of seating shall be given such a configuration that no forces that might result in damages will be transmitted into the container as a consequence of the relative dislocations. Slide plates or foundations with elongated ISO-holes may be provided for instance.

Where such slide plates or other constructional means are provided on supports beside the hatchways in order to relieve the supports of the transverse forces occurring, these forces shall be transmitted into the hatch covers by suitable means. In respect of the de-sign of hatch covers and container supports for the carrying of containers, see also Section 3, A.4.

2. Stowage without lashing or buttressing

2.1 When stowing containers without lashing or buttressing, the transverse loads occurring will have to be absorbed by the transverse framework of the con-tainers. This racking load occurring in the container transverse framework owing to the motion of the ship shall not exceed 150 kN, and locking devices as to 2.2 through 2.4 are to be used.

The load applied to the upper corner casting of the con-tainer may not exceed 848 KN (20' and 40'), 942 kN according to ISO amendment 2005. The limit for the stowage systems is 848 kN.

If 45' Containers are stowed on top of 40' Containers, or vice versa, the corner posts may be loaded with 270 kN maximum. Correspondingly this may be ap-plied for 48’, 49’ and 53’ long containers too.

2.2 Containers in one layer

The containers shall be secured against tilting and shifting by locking devices at their lower corner fit-tings. Where not all of the lower corner fittings of a block of containers are accessible, locking the two

outer containers at least at three corner fittings will do, provided that bridgefitting are arranged.

2.3 Containers arranged in several layers

The containers located in the lowermost layer shall be locked at their lower corner fittings. Cone locks shall be arranged between the container layers. If four con-tainer layers are arranged bridgefitting should be pro-vided athwartships on the uppermost layer so far as possible. Tension-pressure-bridgefitting should be used which can be inserted into variable gap distances between the containers, see also 3.4.2.

2.4 Dunnage

Placing containers on dunnage without lashing them is only permissible where effective securing means pre-venting their shifting and tilting (see 2.2) can be ar-ranged, see also 3.7.

3. On-deck lashing of containers

3.1 The lashings shall be arranged in such a way that 150 kN racking load will not be exceeded in the container transverse framework when taking as basis the load assumptions contained in Section 3, A.

Always both containerends shall be lashed. Both ends have to be lashed in the same way. This is not appli-cable, if one containerend is stowed in a cell guide.

In a stowage system all front-ends respectively all door-ends shall be stowed principally in one section. The door- or front-ends can be arranged forward or backwards. If this requirements is not kept, the stack in question shall be examined separately.

External lashings are generally not permitted. In indivi-dual cases after consultation with GL and appropriate verification approval may be granted

�������� ������

Fig. 2.1 Lashing (internal/external)

I - Part 1 GL 2012

Section 2 Rules for the Arrangement and Construction Chapter 20Page 2–1

A

Page 8: Stowage and Lashing of Containers

3.2 Lashed containers shall be secured against ho-rizontal displacement by cones, locking devices or align-ment steps arranged on the hatch covers and/or on deck.

3.3 Containers in one layer

Lashing is required only where there are no locking devices at the lower corner fittings of the containers. The lashings shall be arranged vertically.

3.4 Containers in more than two layers

3.4.1 Blocks of three or more layers of containers may be lashed in accordance with Fig. 2.1 or in a similar way (see, however, 3.5).

3.4.2 Where the uppermost layer of containers need not be lashed, this layer shall be coupled to the one immediately below by locking devices.

If Containers are stowed in four tiers or more, which need not to be lashed, bridgefittings have to be in-serted on the uppermost tier. Tension-pressure-bridge-fitting are recommended, that can be inserted even if the corner castings are positioned very near to each other.

If the stacks are lashed at both ends, bridgefittings can be deleted.

3.4.3 The lashing force shall, in general, not exceed a SWL of 230 kN for 1st tier top/2nd tier bottom, 270 kN for the 3rd tier bottom and 175 kN for the 2nd tier top respectively (if lashed from level 1st tier bottom). Vertical lashings may impose a load of 300 kN upon the lower corner casting, whereas the upper is limited to 125 kN. See also Annex I.

Due to this the lower corner casting is to be used in case of single lashing (e.g. 2nd tier bottom).

3.5 Where with 5 container layers and more are placed so close to one another (e.g., 20'-containers on 40' stowing places, leaving a 76 mm clearance be-tween them) that lashing at both ends is not possible (see Fig. 2.2), the use of tension-pressure-bridge-fittings on both container ends is recommended (see 3.4.2). If the stacks are lashed of the accessible end, bridgefittings can be deleted there.

3.6 Lashing bridges

To improve the efficiency of the lashing, lashing bridges can be arranged. By this, the lashing, the lash-ing level is risen by one or more tiers.

The dimensioning of the bridge shall be based on the lashing case from the container lashing plan that reaches the highest lashing forces. Alternatively 230 kN per lashing can be applied. The global system of the individual lashing bridge shall be loaded with 61 % of these forces only. The lashing forces have to be applied with their x-, y- and z-components.

The individual lashing plates and their substructures have to be dimensioned based on these values, i.e. depending on angle 230 kN, 270 kN or 300 kN.

In order to calculate the lashing forces on a lashing bridge, 10 mm deformation for 1 tier high bridges (in direction of the load) and 25 mm deformation for 2 tier high bridges shall be taken into account. These maximum deformations have to be considered for dimensioning of the lashing bridges. For higher lash-ing bridges a transverse deformation will be confirmed in the course of approval. Determination of the lashing forces is to be based on this deformation.

A force diagram of the abutment loads is to be submit-ted together with the drawings.

��� �����

����������������������������������

������� ��������� ������������

Fig. 2.2 (5 tiers stowage)

Chapter 20 Page 2–2

Section 2 Rules for the Arrangement and Construction I - Part 1GL 2012

A

Page 9: Stowage and Lashing of Containers

3.7 Coupling elements

If pressure plates or linkage plates are employed, loads should be balanced over a maximum of 3 container stacks only.

Note

Because of operative problems, however, these fittings are not recommended.

3.8 Linear seating of containers

3.8.1 Containers may be stowed in line only in one layer at most. In case of stowage in several layers, the total weight of the containers above the 1st layer shall not exceed the following values:

– with 40'-containers 0,8 G

– with 20'-containers 1,0 G

(G = gross container weight according to ISO). This type of seating can be brought about by arranging continuous steel or wooden dunnages below the longi-tudinal bottom rails of the containers or by directly seating these bottom rails on the hatch covers or the decks with sunk-in pockets being arranged below the container corners.

The arrangement of short steel pads placed upon the girders of short hatch covers and serving as dunnage shall be avoided.

3.8.2 The equipment used for obtaining a linear seating shall be of such a configuration that a suffi-cient clearance (approx. 5 mm) is left between the corner fittings of the container and the hatch covers or decks. For ISO containers, a projecting depth of their corner fittings of from 4 to 17,5 mm as against their bottom longitudinal rails and of from 11 to 17,5 mm as against the bottom transverse girders may be as-sumed in this connection. Special type containers may require additional dunnage for their transportation.

Special care shall be taken to secure linearly seated containers against their shifting sidewards, in confor-mity with 3.2.

3.9 Installation tolerances (build-in)

3.9.1 Height tolerances of container foundations

The following tolerances in height of container resting levels are recommended by GL.

Transverse:

1 point is zero, the other ± 3 mm

Longitudinally:

± 6 mm to zero point (see Annex H)

3.9.2 Length-/width tolerances

Length:5853

11985

+ 3– 3

+ 4– 4

(distance of holecenter- lines for 20')

(distance of holecenter- lines for 40')

Width: 2259 + 3– 3

(distance of holecenter- lines for 20' and 40')

Other containers accordingly. See also in standard ISO 668.

4. Buttress system stowage

4.1 Instead of being lashed, containers may also be secured against their shifting sidewards and/or their tilting by means of buttress structures placed on deck (if necessary, on the hatchways) or by a system com-bined of buttress structures and cone adapters.

4.2 The buttress structures and their connections to the ship's hull are covered by the classification of the ship and shall satisfy the Society's Rules for the Construction of Seagoing Steel Ships.

4.3 The containers shall be shored by the buttress structures in such a way that inadmissible defor-mations of the container framework cannot occur and the permissible container racking loads are not ex-ceeded.

4.4 Cell guides on deck

If the container stowage rises above the cell guide, the uppermost container, which is still to some extent within the guide as well as the containers above, are to be secured sufficiently against racking and lifting forces. Vertical lashings are recommended. In this connection the permissible forces according to 3.4.3 are to be observed.

20' containers can be stowed in "mixed stowage" mode (see B.1.2.7). However, outer stacks shall be additionally secured against swimming up and wind forces by adequate measurements.

5. Endangered containers by wash of the sea

5.1 Containers stowed in positions especially endangered by the wash of the sea and buoyancy forces by incoming water have to be additionally se-cured, in an effective manner, by locking devices, alignment steps increased in height and/or reinforced lashings. It shall be assumed for smaller ships that a buoyancy force corresponding to the entire cubic content of a container may become effective.

5.2 The action of wind gusts shall be taken into account for detached stacks of containers.

I - Part 1 GL 2012

Section 2 Rules for the Arrangement and Construction Chapter 20Page 2–3

A

Page 10: Stowage and Lashing of Containers

B. Below-Deck Stowage of Containers

1. Stowage in cell guide structures

1.1 Cell guide structures for containers may be permanently installed in (welded to) the ship's hull or be arranged in a detachable manner (screwed connec-tions, suspended structures).

1.2 Vertical guide rails

1.2.1 Vertical guide rails consist in general of equal steel angles. On account of abrasion and local forces e.g. due to jamming, occurring when hoisting and lowering the containers, the thickness of the angle flanges should be at least 12 mm.

1.2.2 The horizontal forces originating from the containers are transmitted through the container cor-ners in a punctiform way to the guide rails.

Where vertical guide rails consist of several steel guide angles, the same should be connected with one another by horizontal web plates arranged at the level of the points of attack and additionally at least midway between them.

1.2.3 The top ends of the guide rails shall be fitted with guide heads of sufficiently strong configuration according to operating conditions.

Regarding fatigue strength it is recommended to sup-port guide heads in way of hatch corners only horizon-tally at the transverse bulkhead. A vertical support may be fitted to the longitudinal bulkhead.

It is recommended to provide a vertical connection to the transverse bulkhead in way of the guide heads, to transfer shear force caused by loading and off-loading.

1.2.4 Doubling plates or, aboard ships fitted with an inner bottom ceiling, other suitable means shall be provided at the guide rail lower ends for the purpose of reinforcing the container supporting area (as for reinforcements below the inner bottom, see GL Rules for Hull Structures (I-1-1), Section 21, G.).

1.2.5 Self-supporting rails

Guide rails arranged in a self-supporting manner in the cargo hold shall be sufficiently secured by supports arranged athwartships and fore-to-aft (transverse and longitudinal ties). These supports shall be fitted, if possible, at the level of the container corners.

In case of too high loads, the guide rails may be formed by core sections (e.g., I beams) to which the steel guide angles are attached.

1.2.6 If 20'-containers are stowed in a 40'-cell, normally the containers have to be side-supported in the 20'-gap.

In case a longitudinal stowage system is used (linkage of 2 20'-containers by longitudinal tension/pressure adapter cones to a 40' unit) generally a stack-weight of 1200 kN may not be exceeded. The lowermost con-tainer shall have space for shifting.

1.2.7 Mixed stowage

In case that 40' cell guides are provided, 20' container stacks may be stowed in the 40' cell, secured by single cones between each other and in tank top. This is al-lowed up to 12 tiers. The permissible 20' container stackweights may be taken from Table 2.1 (stackweights in dependence from acceleration and number of tiers).

If the 20' stack is topped by one or more 40' containers (also linked by single cones) higher stackweights are allowed. These weights may be taken from Table 2.2.

In case of container stowage in cell guides with only one containerend in the guide the allowable stack-weights can be calculated by limiting the racking load T1 of the bottom container to 185 kN for 30' and 170 kN for 40' container stowage.

1.2.8 Guide rails at bulkheads

Vertical guide rails at transverse or longitudinal bulk-heads shall be connected to the bulkhead plating or bulkhead stiffeners by horizontal web plates or other elements resistant to shearing and bending loads. A con-nection as free from notches as possible shall be aimed at especially where tank bulkheads are concerned.

1.3 Clearances

1.3.1 The clearance in the guide rails - related to the basic dimensions of the standard containers - shall not exceed 25 mm athwartships and 38 mm fore to aft. In the longitudinal direction of the ship, in connection with the maximum admissible clearance, the deforma-tion of the cell-guide system will have to be consid-ered. Where containers are stowed in less than six layers, larger clearances may be chosen with the con-tainer strength being taken into account.

1.3.2 Athwartships, the spacings of the cell guide system shall be such that any damage to the longitudi-nal supports of the structures or to the containers by deformed container side walls is prevented.

1.4 Cross ties

Depending on the cell guide system construction (see Sec-tion 3, Figs. 3.5 and 3.6), the cross ties serve for shoring the guide rails athwartships or for distributing the local loads among all rails. If ever possible, they shall be ar-ranged at the level of the container corner fittings so as to allow a direct absorption of the horizontal forces. Where they are sufficiently dimensioned, the cross ties may also serve for absorbing the longitudinal forces. Hull deformations, if any, shall also be taken into account.

1.5 Longitudinal ties

Where the longitudinal forces cannot be absorbed by the cross ties, longitudinal ties shall be provided for staying the vertical guide rails.

When steel wire pendants are used for the longitudinal ties, they shall be provided with adjusting devices. Where bars are used, their end connections shall be such as to exclude any compressive stressing.

Chapter 20 Page 2–4

Section 2 Rules for the Arrangement and Construction I - Part 1GL 2012

B

Page 11: Stowage and Lashing of Containers

Table 2.1 20'-Containers in 40'-Cell Guides connected with single cones

k ⋅ bq

tiers 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 0,50 0,51 0,52 0,53 0,54

12 127,2 124,3 121,5 118,6 115,7 112,9 110,6 108,3 106,0 103,7 101,4 99,5 97,6 95,8 93,9

11 126,9 124,0 121,2 118,3 115,4 112,6 110,3 108,0 105,7 103,4 101,1 99,3 97,4 95,5 93,7

10 126,5 123,7 120,8 118,0 115,1 112,3 110,0 107,7 105,4 103,2 100,9 99,0 97,2 95,3 93,5

9 126,2 123,3 120,5 117,7 114,8 112,0 109,7 107,4 105,2 102,9 100,6 98,8 96,9 95,1 93,2

8 125,8 122,9 120,1 117,3 114,4 111,6 109,3 107,1 104,8 102,5 100,3 98,4 96,6 94,7 92,9

7 125,2 122,3 119,5 116,7 113,9 111,1 108,8 106,6 104,3 102,0 99,8 98,0 96,1 94,3 92,5

6 124,3 121,5 118,7 115,9 113,1 110,4 108,1 105,9 103,6 101,4 99,1 97,3 95,5 93,7 91,9

5 123,2 120,4 117,6 114,9 112,1 109,3 107,1 104,9 102,6 100,4 98,2 96,4 94,6 92,8 91,0

4 121,8 119,1 116,3 113,6 110,9 108,1 105,9 103,7 101,5 99,3 97,1 95,3 93,6 91,8 90,0

3 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 90,5 89,5 88,5 87,5

2 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0

k ⋅ bq

tiers 0,55 0,56 0,57 0,58 0,59 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69

12 92,0 90,5 88,9 87,4 85,8 84,3 83,0 81,7 80,4 79,1 77,7 76,6 75,5 74,4 73,3

11 91,8 90,3 88,7 87,2 85,6 84,1 82,8 81,5 80,2 78,9 77,6 76,4 75,3 74,2 73,1

10 91,6 90,1 88,5 87,0 85,5 83,9 82,6 81,3 80,0 78,7 77,4 76,3 75,2 74,1 72,9

9 91,4 89,8 88,3 86,8 85,2 83,7 82,4 81,1 79,8 78,5 77,2 76,1 75,0 73,9 72,8

8 91,1 89,5 88,0 86,5 84,9 83,4 82,1 80,8 79,5 78,2 76,9 75,8 74,7 73,6 72,5

7 90,6 89,1 87,6 86,1 84,5 83,0 81,7 80,4 79,2 77,9 76,6 75,5 74,4 73,3 72,2

6 90,0 88,5 87,0 85,5 84,0 82,5 81,2 79,9 78,6 77,4 76,1 75,0 73,9 72,8 71,7

5 89,2 87,7 86,2 84,7 83,2 81,7 80,4 79,2 77,9 76,6 75,4 74,3 73,2 72,1 71,0

4 88,2 86,7 85,3 83,8 82,3 80,8 79,6 78,3 77,0 75,8 74,5 73,5 72,4 71,3 70,3

3 86,6 85,1 83,6 82,2 80,7 79,3 78,0 76,8 75,6 74,4 73,1 72,1 71,0 70,0 68,9

2 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0

I - Part 1 GL 2012

Section 2 Rules for the Arrangement and Construction Chapter 20Page 2–5

B

Page 12: Stowage and Lashing of Containers

k ⋅ bq

tiers 0,70 0,71 0,72 0,73 0,74 0,75 0,76 0,77 0,78 0,79 0,80

12 72,1 71,2 70,2 69,2 68,3 67,3 66,4 65,6 64,7 63,9 63,1

11 72,0 71,0 70,0 69,1 68,1 67,1 66,3 65,5 64,6 63,8 62,9

10 71,8 70,9 69,9 68,9 68,0 67,0 66,2 65,3 64,5 63,6 62,8

9 71,6 70,7 69,7 68,8 67,8 66,8 66,0 65,2 64,3 63,5 62,6

8 71,4 70,4 69,5 68,5 67,6 66,6 65,8 64,9 64,1 63,3 62,4

7 71,1 70,1 69,2 68,2 67,3 66,3 65,5 64,6 63,8 63,0 62,1

6 70,6 69,7 68,7 67,8 66,8 65,9 65,0 64,2 63,4 62,5 61,7

5 70,0 69,0 68,1 67,1 66,2 65,3 64,4 63,6 62,8 62,0 61,2

4 69,2 68,3 67,3 66,4 65,5 64,5 63,7 62,9 62,1 61,3 60,5

3 67,9 66,9 66,0 65,1 64,2 63,3 62,5 61,7 60,9 60,1 59,3

2 61,0 61,0 61,0 61,0 61,0 61,0 60,2 59,4 58,7 57,9 57,2

k · bq = transverse acceleration factor ( see Section 3, A.2)

For ships with acceleration factors below 0,50 individual calculations of the lateral accelerations are required.

Permissible 20' container stackweights [t] for stowage in hold cell guides. Shown container stack weights are not to be exceeded. Inside the container stack the single container

weights may differ from each other. Calculated acceleration factors are to be rounded up to two decimal places maximum.

Table 2.2 20'-Container-stack "topped" with minimum one 40'-container on single cones

k ⋅ bq

tiers 0,40 0,41 0,42 0,43 0,44 0,45 0,46 0,47 0,48 0,49 0,50 0,51 0,52 0,53 0,54

12 203,5 199,2 194,9 190,6 186,3 182,0 178,1 174,3 170,5 166,7 162,9 159,9 156,9 154,0 151,0

11 200,3 196,1 191,8 187,5 183,2 179,0 175,2 171,5 167,8 164,1 160,3 157,4 154,5 151,6 148,7

10 197,5 193,0 188,5 184,0 179,5 174,9 171,4 168,0 164,5 161,0 157,5 154,6 151,8 148,9 146,0

9 193,2 188,9 184,5 180,1 175,7 171,3 167,9 164,5 161,1 157,7 154,3 151,5 148,7 145,9 143,1

8 188,3 184,2 180,0 175,8 171,6 167,5 164,1 160,8 157,4 154,1 150,7 148,0 145,3 142,5 139,8

7 182,6 178,6 174,5 170,5 166,5 162,4 159,2 155,9 152,7 149,5 146,2 143,6 140,9 138,3 135,7

6 176,3 172,4 168,5 164,6 160,7 156,8 153,7 150,6 147,5 144,3 141,2 138,7 136,1 133,6 131,0

5 152,4 151,9 151,5 151,0 150,6 150,1 147,1 144,2 141,2 138,2 135,2 132,8 130,4 127,9 125,5

4 121,9 121,9 121,9 121,9 121,9 121,9 121,9 121,9 121,9 121,9 121,9 120,8 119,7 118,6 117,5

3 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4

2 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0

Chapter 20 Page 2–6

Section 2 Rules for the Arrangement and Construction I - Part 1GL 2012

B

Page 13: Stowage and Lashing of Containers

k ⋅ bq

tiers 0,55 0,56 0,57 0,58 0,59 0,60 0,61 0,62 0,63 0,64 0,65 0,66 0,67 0,68 0,69

12 148,1 145,6 143,1 140,6 138,2 135,7 133,6 131,5 129,4 127,3 125,2 123,4 121,7 119,9 118,1

11 145,8 143,3 140,9 138,5 136,0 133,6 131,6 129,5 127,4 125,4 123,3 121,6 119,8 118,0 116,3

10 143,2 140,8 138,4 136,0 133,6 131,3 129,2 127,2 125,2 123,2 121,2 119,4 117,7 116,0 114,3

9 140,3 137,9 135,6 133,3 130,9 128,6 126,6 124,6 122,7 120,7 118,7 117,0 115,3 113,6 111,9

8 137,1 134,8 132,5 130,2 127,9 125,6 123,7 121,8 119,9 117,9 116,0 114,3 112,7 111,0 109,4

7 133,0 130,8 128,6 126,4 124,2 122,0 120,1 118,3 116,4 114,5 112,7 111,1 109,5 107,9 106,3

6 128,5 126,4 124,2 122,1 120,0 117,9 116,0 114,2 112,4 110,6 108,8 107,3 105,8 104,2 102,7

5 123,1 121,0 119,0 116,9 114,9 112,9 111,2 109,4 107,7 106,0 104,3 102,8 101,3 99,8 98,4

4 116,4 114,5 112,6 110,6 108,7 106,8 105,2 103,5 101,9 100,3 98,7 97,3 95,9 94,5 93,1

3 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 91,4 90,2 88,9 87,6 86,4

2 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0

k ⋅ bq

tiers 0,70 0,71 0,72 0,73 0,74 0,75 0,76 0,77 0,78 0,79 0,80

12 116,3 114,7 113,2 111,6 110,1 108,5 107,2 105,8 104,4 103,1 101,7

11 114,5 113,0 111,5 109,9 108,4 106,9 105,5 104,2 102,9 101,5 100,2

10 112,5 111,0 109,5 108,0 106,5 105,0 103,7 102,4 101,1 99,8 98,5

9 110,3 108,8 107,3 105,8 104,4 102,9 101,6 100,3 99,1 97,8 96,5

8 107,7 106,3 104,8 103,4 102,0 100,5 99,3 98,0 96,8 95,5 94,3

7 104,7 103,3 101,9 100,5 99,1 97,7 96,5 95,3 94,1 92,8 91,6

6 101,1 99,8 98,4 97,1 95,8 94,4 93,2 92,1 90,9 89,7 88,6

5 96,9 95,6 94,3 93,0 91,7 90,5 89,3 88,2 87,1 86,0 84,9

4 91,7 90,5 89,3 88,0 86,8 85,6 84,5 83,5 82,4 81,4 80,3

3 85,1 84,0 82,9 81,7 80,6 79,5 78,5 77,5 76,5 75,5 74,6

2 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0 61,0

k · bq = transverse acceleration factor ( see Section 3, A.2)

For ships with acceleration factors below 0,50 individual calculations of the lateral accelerations are required.

Permissible 20' container stackweights [t] for stowage in hold cell guides. Shown container stack weights are not to be exceeded. Inside the container stack the single container weights may differ from each other. Calculated acceleration factors are to be rounded up to two decimal places maximum.

I - Part 1 GL 2012

Section 2 Rules for the Arrangement and Construction Chapter 20Page 2–7

B

Page 14: Stowage and Lashing of Containers

2. Stowage and lashing without cell guide structures

2.1 Stowage without lashings

2.1.1 Where containers are to be stowed below deck, without making use of special cell guide struc-tures or lashings, every block of containers (containers placed beside, and on top of, one another and coupled to each other by suitable appliances such as cone adapters and bridgefitting) shall be laterally shored at its ends, through the container corner fittings, against sufficiently strong structural elements of the ship (such as decks, web frames). When determining the shoring forces, hull deformations, if significant, shall also be taken into account.

The number of lateral shoring points shall be deter-mined so that the corner fitting loads (see Section 3, A.6.1) and racking loads permitted for the containers will not be exceeded. Where necessary, the shoring force shall be distributed, by a special configuration of the shoring element, among the two corner fittings located one atop the other at any one shoring point.

The shoring force occurring may also be reduced by splitting up the inertia forces acting athwartships into a compressive load on the one and a simultaneously effective tensile load on the other side of the ship at the respective shoring points there. This may be at-tained by an adequate construction of the shoring element (see 2.1.2) and splitting up the containers to be shored into two separate blocks of containers. Naturally a securing of the containers by twistlocks and lashing is allowed too.

2.1.2 Shoring element construction

The shoring element may be so constructed as to be able to transmit both compressive and tensile loads. It may be arranged in a permanent or removable manner. Both types of construction shall be of such a configu-ration that the clearance between their contact faces and the container corner fittings is as small as possi-ble. Wedges shall be sufficiently secured against their inadvertently getting loose (e.g., on account of vibra-tions).

The shoring elements shall be easily accessible. The weight and number of loose parts shall be restricted to a minimum.

2.1.3 The container stacks placed beside one an-other be coupled by dual cone adapters or equivalent devices. Bridgefitting shall be provided on the upper-most layer of containers if there is a lateral shoring point at this level. These bridgefitting shall be suitable for pressing the containers against each other and against the lateral shoring points. Where the contain-ers are divided into two separate blocks (see 2.1.1), bridgefitting for tension and compression are to be arranged at the support level. The lowest container layer has to be secured against shifting at all 4 corner castings.

2.2 Lashing in the cargo hold

In place of rigidly shoring the blocks of containers as described in 1., they may also be secured by ropes or lashing bars, e.g. in those cases where shoring them by means of shoring elements as to 2.1.1 is impossible for lack of suitable shoring points in the ship's hull. The provisions in A.3. shall apply analogously.

2.3 To secure a block of containers, a combined shoring/lashing system may be used if necessary.

3. Hatchcoverless container ships

3.1 Longitudinal and transverse acceleration

The accelerations are to be determined in general according to Section 3, A.

For a ship's length of 120 m 4 tiers, for a ship's length of 270 m 9 tiers are to be considered as con-tainers under deck. Lengths in between are to interpo-lated linearly.

The transverse loads shall be increased by the values given in Section 3, A. for 2nd tier and higher accord-ingly for containers which side walls are exposed to wind pressure.

3.2 Stackability

According to ISO 1496/1 the lowermost container in hold may be overstowed with 192.000 kg (vertical acceleration of 1,8 g included). This value can be converted in accordance with the vertical acceleration given in these rules. However, a special safety factor of 1,2 shall persist. A maximum number of tiers is not given.

Chapter 20 Page 2–8

Section 2 Rules for the Arrangement and Construction I - Part 1GL 2012

B

Page 15: Stowage and Lashing of Containers

Section 3

Design Principles

A. Calculation of the Lashing and Shoring Forces

1. Assumptions for the determination of the forces

1.1 The forces acting on the containers can be subdivided into two groups:

– static forces

– dynamic forces

The static forces result from the components of the container gross weights with the ship heeling and from the prestressing of the lashings, if any. Prestressing shall be kept as small as possible and can be neglected in calculations.

The dynamic forces acting upon the containers mainly result from the ship's pitching, heaving and rolling as well as the action of the wind. These forces shall be taken into account and calculated while applying the formulae contained in 2., 3. and 4.

1.2 Any shifting of the containers increases the load acting upon some lashing elements. Owing to the clearance at the cone adapters and the lower shifting locks, displacement of the individual container is possible on principle. Where more than three stacks of containers coupled to each other by double cone adapters are located side by side, it may in general be assumed, however, that no shifting will take place as the clearance will be zero at a sufficient number of points. In all other cases at the door side in the 1st layer the displacement to be considered is 0,4 cm; the same applies to the 2nd layer. For the front walls, in general, no displacement is to be considered in the computations.

1.3 Normally, containers shall be stowed in fore-to-aft direction. Stowing containers athwartships shall be agreed upon from case to case with the Owner and GL.

1.4 Lashings shall in general be arranged at the front and rear end of any one block of containers (con-tainers placed side by side and atop one another).

1.5 Forces acting transversely on the container (transverse forces)

Owing to the ship's motions and the wind, the con-tainer, including its cargo, is exposed to a transverse force Fq (see 2.) which may be assumed to act evenly

on its side wall. 55 % of this force is transmitted by the lower and 45 % by the upper container longitudi-nal to the transverse end frames, if the gravity centre height is assumed at 45 %.

The share 0,225 ⋅ Fq transmitted through the upper longitudinal takes effect as transverse force in the end frame of the respective container. In case of several containers stacked upon each other, this transverse force is increased by the sum of the transverse forces taking effect in the frames placed atop the transverse frame under consideration. In lashed containers, the forces occurring in the transverse frames (racking loads) are reduced by the horizontal components of the lashing forces.

Resultant transverse force T: See 5.2.

The racking loads shall not exceed the values permit-ted for the types of containers in question. Since 1971, the permissible racking load as to the respective ISO standard amounts to 150 kN.

1.6 Forces in longitudinal direction

The assumptions indicated in 1.5 apply by analogy to the stressing of the container in longitudinal direction. The corresponding permissible load is 125 kN ISO test load is 75 kN.

2. Determination of the transverse compo-nents Fq

2.1 The determination of the transverse accelera-tion factor "k ⋅ bq" by formulae below is only permit-ted for load cases, where a metacentric height (GM0) does not exceed the following value:

2

00,04 BGM

Z⋅

=

B = ship's breadth at outer edge of frames [m]

GM0 = initial metacentric height [m]

Note

This is the maximum allowable GM0 value for con-tainer stowage systems that are calculated according to "standard acceleration".

cont.Z h H [m]= +

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–1

A

Page 16: Stowage and Lashing of Containers

hcont. = maximum in stowage and lashing plan as-signed number of container tiers (ntiers) on hatch covers - or on weatherdeck, if no hatch covers are provided - multiplied by 1,05

cont. tiersh n 1,05 [m]= ⋅

H = vertical distance between designed waterline and lower edge of container stack considered.

2.2 Reductions of the transverse acceleration are possible for ship lengths greater than L = 120 m if the following, in comparison with 2.1 decreased initial metacentric heights are not exceeded at the load cases intended. The decreased maximum initial metacentric height shall be calculated as follows:

2

00,018 BGM

Z⋅

=

This 0GM value− shall be entered into the stowage plan to be approved GL.

Note

This is the maximum allowable GM0 value for con-tainer stowage systems that are calculated accordance with "reduced acceleration".

2.3 The factor k allows for the influence of the container fore-to-aft location and shall be calculated as follows:

0,75 xAP to 0,2 k 1,15 ⋅>> = −L

L

0, 2 to 0,6 k 1,0>> =L L

0,75 x0,6 to FP k 0,55 ⋅>> = +L

L

x = distance of the container's center of gravity from A.P., in [m]

L = ship's length between perp. in [m]

Table 3.1 Transverse acceleration factor "bq" not reduced

ship length range on weather deck "bq" below weather deck "bq"

range 1 L ≤ 120 m 1,32 – 0,005 ⋅ L 1 1,2 – 0,005 ⋅ L 2

range 2 120 m < L < 170 m 0,84 – 0,001 ⋅ L 0,648 – 0,0004 ⋅ L

range 3 and 4 L ≥ 170 m 0,67 0,58

1 not exceeding 0,9 and k ⋅ bq not exceeding 1,0 2 not exceeding 0,8 and k ⋅ bq not exceeding 0,9

See Fig. 3.1

Table 3.2 The reduced transverse acceleration factor "bq" is to be determined according to table below:

ship length range on the weather deck "bq" below weather deck "bq"

range 2 120 m < L < 170 m 1,008 – 0,0024 ⋅ L 0,792 – 0,0016 ⋅ L

range 3 170 m ≤ L ≤ 220 m 0,77 – 0,001 ⋅ L 0,588 – 0,0004 ⋅ L

range 4 L ≥ 220 m 0,55 0,50

Chapter 20 Page 3–2

Section 3 Design Principles I - Part 1GL 2012

A

Page 17: Stowage and Lashing of Containers

��� ��� ��� ��� ��� ���

���

����

���

����

���� ����

��

���

����

���

� � ��

��������������������� !"��#

����$%�

&'(�� ���'(��

����)$%�

&

������

��)�

����

Abb. 3.1

As minimum value for the acceleration of deck con-tainers 0,5 · g is to be taken unless individual calcula-tions are on hand at GL.

Reduced acceleration values shall not be used for constructions in hold.

Accelerations for GM-values higher than given in these rules are to be agreed upon with GL.

2.3.1 A side of the reduced and not reduced method for calculation of transverse acceleration a ship individual calculation is possible by GL upon inquiry.

Note

The individual determination of the transverse accel-erations is recommended for larger ships. Here the maximum GM-values are chosen generally in accor-dance with "standard" and "reduced" accelerations. However, other GM-values requested could be se-lected for the determination of the accelerations.

2.3.2 To be able to determine the accelerations for actually existing GM-values on board, it is allowed to interpolate the acceleration values between "standard", "reduced" and/or "individual".

If it is interpolated between "individual" and "stan-dard", it is allowed to interpolate up to 10 % above the "standard" GM-value.

If it interpolated between accelerations of GM "re-duced" and "standard", it is allowed to extrapolate by 20 % over the "standard" value.

It is not allowed to extrapolate below the GM "re-duced" value or the smallest GM "individual" value.

The calculated transverse acceleration factor bq is only valid up to the GM value used for its calculation.

2.4 Wind loads

The transverse components Fq shall be increased by the values given in the following table for containers the side walls of which are exposed to wind pressure.

Table 3.3

Wind load Fw per container [kN ]

container type 20' 40'

1st tier 30 60

2nd tier and higher 15 30

The stated values are valid for 8' 6" high containers. For other container heights and lengths the wind force has to be converted.

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–3

A

Page 18: Stowage and Lashing of Containers

The first tier contains a share for sea-sloshing. The windload is to be imposed on all outboard- or free-standing stacks. If inside positioned stacks from a gap, free standing stacks are to be imposed with windload only, if the gap is three or more gaps wide.

Where container stacks placed side by side are cou-pled to one another athwartships by cone adapters, the value Fw/m shall be taken as wind load for each con-tainer in the calculation of the lashing forces.

n = number of container stacks in athwartships direction (nmax = 3)

The transverse component Fq for determination of lashing and racking forces in container frames, work-ing parallel to the deck, are to be calculated by follow-ing formulae:

q q wF [G k 9,81 b ] F [kN]= ⋅ ⋅ ⋅ +

G = weight of a container including cargo in tons [t]

k = factor for container position

bq = transverse acceleration factor

Fw = wind load for a container in outboard stacks see 2.3

3. Determination of the longitudinal compo-nent Fl

The longitudinal component Fl for determining the fore- and aft stressing of the container buttress and cell guide structures as well as supports, and for determin-ing the racking loads in the longitudinal walls of con-tainers stowed in fore-to-aft direction, shall be calcu-lated by means of the following formulae:

F G b [kN],= ⋅l l

where bl -values for containers located between the lowermost layer in the cargo hold and the lowermost layer on deck shall be determined by interpolation, for containers above the first layer on deck by linear ex-trapolation.

4. Loads on container stanchions and sub-structures

4.1 Substructures for laterally supported con-tainers

4.1.1 The stanchions and substructures are to be dimensioned, taking into account the forces arising vertically to the deck from the container (stack) stowed on the stanchions.

4.1.2 For systems with lateral support of the con-tainer blocks as well as for container blocks with lon-gitudinal connections the vertical force Pv is calcu-lated as follows:

v vP V (1 b ) 9,81 [kN]= ⋅ + ⋅

Pv = vertical load on the container support [kN]

V = proportionate weight on the support by con-tainer or stack of containers [t]

bv = acceleration factor as follows:

0v

vb 0,11 m⎛ ⎞= ⋅ ⋅⎜ ⎟

⎝ ⎠L

m 1,0

xfor 0,2 0,7

=

≤ ≤L

o o

xm m 5 (m 1)

xfor 0 0,2

= − −

≤ <

L

L

0m 1 xm 1 0,70,3

xfor 0,7 1,0

+ ⎛ ⎞= + −⎜ ⎟⎝ ⎠

< ≤

L

L

0o

vm 1,5 0,11⎛ ⎞= + ⋅⎜ ⎟

⎝ ⎠L

L = ship's length between perpendiculars in [m]

x = distance from the aft perpendicular in [m]

v0 = maximum speed in calm water in [kn], see GL Rules for Hull Structures (I-1-1), Section 1. v0 shall not be taken less than L [kn].

Table 3.4 Longitudinal acceleration factor bl

for lowermost container in cargo hold for lowermost container on deck

120 m : b 0,22 9,811710

⎛ ⎞≤ = − ⋅⎜ ⎟⎝ ⎠

LL l

120 m : b 0,15 9,81> = ⋅L l

For any length of the ship:

b 0,35 9,811000

⎛ ⎞= − ⋅⎜ ⎟

⎝ ⎠

Ll

As for L and G, see 2.1 bl in [m/s2]

min bl = 0,15 ⋅ 9,81 bl in [m/s2]

Chapter 20 Page 3–4

Section 3 Design Principles I - Part 1GL 2012

A

Page 19: Stowage and Lashing of Containers

4.2 Foundations/container stanchions stowage bridges for container stacks with lashing and/or twistlocks (without lateral support)

4.2.1 The stanchions and substructures are to be dimensioned, taking into account the simultaneously acting forces arising horizontally and vertically to the deck from the container (stack) stowed on the stan-chions.

The vertical forces P1' and P1" are to be calculated as follows:

[ ]'H V1P F F kN= +

[ ]"H V1P F F kN= −

[ ]q1 1 q2 2 qn nH

C

F h F h ..... F hF kN

2 B⋅ + ⋅ + + ⋅

=⋅

( ) [ ]1 2 n t

VG G ..... G b 9,81 cos 30

F kN4

+ + + ⋅ ⋅ ⋅ °=

P2', P3' and P4' or P2", P3" and P4" can be calculated corresponding to this formula

P1' = vertical load on the container support

P1" = lifting force

BC = 2,260 [m] for ISO-containers (8' width)

G = weight of a container including cargo

Fq = See 2.4 (for outside stacks the wind loads have to be considered)

h = height to the centre of gravity of the con-tainer [m].

The centre of gravity is to be set to 0,45 × container height.

k = see 2.3

t70b k 1

70⎛ ⎞

= ⋅ +⎜ ⎟+⎝ ⎠L

= container position correction factor

If the container stacks are lashed, this will have to be taken into account, when calculating the vertical forces P" and P'.

The most unfavourable dislocation on the stanchion of the vertical force P1' is to be assumed.

P1' has to be taken into account simultaneously with the horizontal force

T1 + 0,275 ⋅ Fq1

If the transverse component Fq at the lower edge of the 1st container layer is not intended to be determined separately, a maximum value of 210 kN is to be as-sumed.

In cases where the bending strength of the stanchions is smaller in longitudinal than in transverse direction, also the action of the maximal longitudinal force ac-cording to 3. (the container stack weight has to be taken) is to be considered. The vertical force acting simultaneously in this case is to be taken as P1'.

4.2.2 Container stanchions provided only with a sliding plate, respectively an athwartships arranged "dove tail base" at their upper end are to be dimen-sioned according to vertical loads as to 4.2.1 and to horizontal friction forces resulting from these vertical loads. The horizontal force, however, need not be taken greater than the one producing a deflection equal to the maximum possible dislocation of the container (usually, abt. 7 mm). In case of major de-formations of hatches - e.g. with long hatches - they are to be taken into account in connection with hori-zontal shifting (friction coefficient μ = 0,25 for cast/steel, μ = 0,50 for steel to steel, other combina-tions upon agreement).

%*

+,,�

+,�

+,�

+,�

+,�

+,,�

+,,�

+,,�

-�.�

-�

-�

��

��

��

/��

/��

/��

/������

-�

Abb. 3.2

4.2.3 Where lashings are arranged at the stan-chions, the stanchions are to be dimensioned also according to the vertical and horizontal loads resulting from the lashing forces.

Where container foundations are used which may be moved in transverse direction, appropriate measures shall be taken to avoid additional stresses of the lash-ings.

4.2.4 Detached stanchions are to be designed so that shocks occurring during normal loading opera-tions can be safely absorbed.

4.2.5 In the event of major hatch deformations it will also have to be taken into account that the con-tainers arranged on the stanchion and the cover and/or between two covers do not resist the shifting forces.

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–5

A

Page 20: Stowage and Lashing of Containers

4.3 Container foundations

Container foundations welded on and/or welded in have to be dimensioned analogously to 4.2.

It will have to be ensured that the vertical force is prop-erly introduced into the foundation through the twist-lock casing and/or the stacking cone. Thus, in the event of loads exceeding 600 kN (700 kN max. pressure for twistlock at 1st tier top and higher) the minimum sur-face of direct pressure transmission of the twistlock (i.e., the web surface of the corner fitting covered by the twistlock foundation plate) is to be 25 cm2.

Note

At twistlock foundations with elongated ISO holes an even larger base is recommended in the sense of a longer life time.

Depending on the container weights, the stacking heights and the accelerations, lifting forces occur at the foundations. In view of this, the foundation structure, including its substructure, will have to be dimensioned satisfactorily. (For calculation and maximum admissi-ble lifting forces at the container corner fitting, see 4.4).

Foundations welded in to the ship's longitudinal main structures (strength deck, inner bottom, etc.) the strength of the structural stress has to be considered for the sizing of the foundations.

4.4 Lifting forces at container castings and container foundations

4.4.1 Where the arrangement of the container stacks is such that tilting may occur, the forces in-duced in the lashing elements thereby are to be spe-cially considered.

Also it will have to be checked, whether in case of securing of the containers by twistlocks only (racking force T1 ≤ 150 kN) the admissible SWLs (tension) of the twistlocks and of the container foundations are not exceeded.

The maximum admissible tensile load at the container corner fitting is 250 kN, so that twistlocks and founda-tions can be designed for this value.

The lifting forces P" are to be determined according to 4.2.1 (see Fig. 3.2).

If the admissible value for the container corner fittings of 250 kN is exceeded, relevant measures (additional lashings, reduction in container weights, etc.) will have to be taken to ensure observance of the admissible load.

Up to a calculated remaining lifting force of 375 kN a vertical lashing can be applied for balance of the forces. This lashing shall be "loose" to equalize the clearance in the twistlock. This equalization could also be done by spring-elements.

4.4.2 Substructures for container foundations are to be determined according to GL Rules for Hull Struc-tures (I-1-1).

4.5 Permissible stresses

The following permissible stresses are observed for supports, foundations, etc.:

eHN

R1,25

σ =

eHR2,5

τ =

2 2 eHv N

R31,13

σ = σ + τ =

σN = perm. normal stress [N/mm2] (tension, com-pression, bending)

τ = perm. shear stress [N/mm2]

σv = perm. equivalent stress [N/mm2]

ReH = reference yield point of the material used (see B.2.2) [N/mm2]

It has to be observed that transitions into the deck, into longitudinal coamings etc. shall be built sufficiently smooth in order to avoid peaks of tension.

5. Determination of the forces in the lashing system

5.1 The lashing forces as well as the forces taking effect in the container transverse framework follow from the elastic deformation of the lashings and the transverse frames, from the shifting, if any, of the con-tainers and from the prestressing, if any, of the lashings.

5.2 Forces and deformations

The determination of the racking loads T and the lash-ing forces Z is shown by means of a simple example (see Fig. 3.3). In this connection, the deformations of the container and the lashing elements at the various lashing points are on principle equated to one another with any possible shiftings being taken into account. Therefrom results a set of equations for the unknown lashing forces and racking loads.

-�

&$�0��

-�&1&�23&

/����

�/��

��

Fig. 3.3

Chapter 20 Page 3–6

Section 3 Design Principles I - Part 1GL 2012

A

Page 21: Stowage and Lashing of Containers

1 q2 q1 01T F 0,225 F sin (Z Z) [kN]2

= + − α + Δ

(Fq1 and Fq2 = transverse forces, see 2.)

Z0 = prestressing (see 1.1)

zAZ E sin [kN]Δ = δ ⋅ ⋅ ⋅ αl

(lashing force alteration due to external forces Fq)

A = effective cross-section of lashing [cm2]

Ez = overall modulus of elasticity of lashing

For lashing steel bars (including tensioning device and eye) depending on composition the following values can be used:

4 4 2zE 1, 4 10 1,9 10 [kN / cm ]= ⋅ ÷ ⋅

Unless the documentation submitted contains any data to the contrary, Germanischer Lloyd will base their lashing computations on the following values:

l1 l2

1st layer top 2nd layer bottom

354 cm 365 cm

α = 43°α = 41°

E-module lashing rod 1,4 ⋅ 104 [kN/cm2]

l3 l4

2nd layer top 3rd layer bottom

560 cm 575 cm

α = 24°α = 22°

E-module lashing rod 1,75 ⋅ 104 [kN/cm2]

l5 l6

3rd layer top 4th layer bottom

710 cm 725 cm

α = 19°α = 18°

E-module lashing rod 1,9 ⋅ 104 [kN/cm2]

cz = spring constant of lashing

zz

E Ac [kN / cm]

⋅=

l

Hence

zZ c sin [kN]Δ = δ ⋅ ⋅ α

l = length of lashing [cm]

Z = Z0 + ΔZ = total lashing force [kN]

δ = cc ⋅ T1 + v = transverse dislocation at upper edge of container

cc = resilience of the container transverse frame; where the resilience values of the containers to be stowed are unknown, the following mean values may be used for steel frame con-tainers:

Door frame [cm/kN]

Front wall frame [cm/kN]

2,7 ⋅ 10–2 0,60 ⋅ 10–2 In case of aluminium containers, the values of cc are to be specially agreed.

5.3 Load attacking angles between 40° and 45° the max. SWL is 230 kN, at angles between 20° and 25° 270 kN for the lower corner casting and 175 kN for the upper. In vertical direction the lower corner casting may be loaded with 300 kN, the upper with 125 kN (see Annex I). If corresponding technical proof is given. The max. SWL can be risen up to 300 kN for other load angles.

6. Shoring of containers in the cargo hold - determination of the forces

6.1 Permissible loads on the corner fittings

6.1.1 In cases where the shoring forces are deter-mined according to 6.3, the admissible forces are as follows:

at the upper corner fittings:

– 250 kN tension/compression

at the lower corner fittings:

– 400 kN tension/compression

Where containers are stowed that may not be stressed by the loads mentioned above on account of their type of construction, the maximum lateral shoring loads shall be adequately reduced (see also ISO 1496/I).

6.1.2 In general, in the longitudinal direction of the containers, the supporting forces as listed below shall not be exceeded:

At the upper corner fittings:

– 125 kN tension/compression

(only for closed type containers, so-called box containers).

For tank containers, open-top containers, open-side containers and platform-based containers:

– 75 kN tension/compression

At the lower corner fittings:

– container weight

6.2 Calculation in case of containers forming a block

Where several rows of containers, connected with double cones horizontally are to be supported, the shoring force Fq is to be determined according to 6.3.

Where the number of rows is greater than 4, the forces H may be reduced by the following factor fr:

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–7

A

Page 22: Stowage and Lashing of Containers

2

r(n 4)if (n m) 4, the factor f 12 n m

−− ≤ = −

⋅ ⋅

r8 m(n m) 4, the factor f2 n

+− > =

If the container block is not complete i. e. tanks in fore ship region, the container layers m, respectively the container stacks n are to be determined as follows:

number of layers m:

1. biggest number of layers of the Section considered / 3 = result A (complete numbers without decimals only)

2. Original total number of layers to be reduced by result A.

The layers that have less rows than A are deleted.

This gives the new number of layers. number of stacks n: 1. new number of layers (see above) /

2 = result B (complete numbers without decimals only)

2. Stacks are to be neglected, which layers are smaller or equal to result B.

Tank steps still existing are not considered.

The newly determined number of layers and stacks are to be inserted into the formula for the reduction fac-tors. m = number of container layers n = number of container stacks to be supported at

the respective shoring point. Where two opposite shoring points are de-

signed to act simultaneously in tension and compression, n shall only be taken as half the number of piles.

Reduction is admissible only if the requirement

r0,3 m G 9,81 (1 f ) 150 kN⋅ ⋅ ⋅ ⋅ − ≤

is met.

6.3 Rigid shoring

Where a largely rigid shoring of the containers may be assumed on account of the ship's construction under consideration, the shoring loads may be determined to a sufficient degree of accuracy as follows (example):

q q reF 9,81 G b k f2

= ⋅ ⋅ ⋅ ⋅ ⋅

e = number of containers to be supported

G = Container gross weight in tons [t]

bq = transverse acceleration factor in hold accord-ing to 2.1 respect. 2.2

k = factor for container position acc. to 2.3

fr = Reduction factor to 6.2

In the following the number of containers to be sup-ported is demonstrated basing on a block with two supports, 5 layers and x stacks.

The load from the container layers is to be distributed ideally to the supports.

Hence the load from both uppermost container layers (see Fig. 3.4) can be distributed in equal shores to both supports. Both supports are loaded with

q q r2 number of stacksF 9,81 G b k f

4⋅

= ⋅ ⋅ ⋅ ⋅ ⋅

Additionally the lower support is loaded with the proportional share from the 3 lower container layers. These loads go equally into the lower support and into tank top with:

q q r5 number of stacksF 9,81 G b k f

4⋅

= ⋅ ⋅ ⋅ ⋅ ⋅

Remaining shear forces are transmitted into the double bottom.

�44����44���

�������44���

����������"�� �0����44����44���

����������"�� �0����������44���

����������"�� �0���������������

/�

/�

/�

Fig. 3.4

7. Safety factors for container lashing ele-ments

Br

Br

Br

safety factor in general: 2,0

for lashing ropes applies factor: 2,25

: 2,50for lashing chains applies factor

υ =

υ =

υ =

7.1 Above factors apply for rigid fittings that are imposed by tension, pressure and bending..

See also Annex C.

Chapter 20 Page 3–8

Section 3 Design Principles I - Part 1GL 2012

A

Page 23: Stowage and Lashing of Containers

B. Design of the Cell Guide Structures

1. General

1.1 Shoring structures may be constructed in accordance with the following guide lines.

Necessary calculations may be carried out with suit-able computer programs. In this case the computer model, the boundary conditions and load cases are to be agree upon with Germanischer Lloyd. The calcula-tion documents are to be submitted including input and output.

1.2 Where parts of the cell guide structures are also components of the ship's hull, the GL Rules for Hull Structures (I-1-1) shall be taken into considera-tion as well.

2. Permissible stresses

2.1 The resultant stresses calculated shall not exceed the limit values specified in A.4.5.

2.2 Reference yield point

The reference yield point is the value which shall be taken as a basis for the calculation. A distinction is to be made:

– If the yield point of the material of a structional member has not been determined by test, there shall not be used a value exceeding 0,6 of the tensile strength of the material.

– If the proven yield point and the nominal yield point of the material of a structural member ex-ceeds 0,7 of the tensile strength, only 0,7 of this strength may be taken into account.

2.3 In this connection the lower limit of the nominal tensile strength of the material is considered as tensile strength.

2.4 Safety against buckling

The safety against buckling of cross tie sections in cell guide structures with compressive loads shall be proofed as follows:

The sectional area of tie bars is not to be less than:

2ss req

p

PA 10 [cm ]= ⋅

σ

σp = permissible compressive stress [N/mm2]

= eHRSκ

As = sectional area of tie bar [cm2]

Ps = tie bar load [kN]

κ = reduction factor

= 2 2

s

1

φ + φ − λ

φ = ( ) 2p s s0,5 [1 n 0,2 ]+ λ − + λ

= 0,34 for tubular and rectangular profiles

= 0,49 for open sections

λs = degree of slenderness of the tie bar

= s eH

s

R. 0,2

i E≥

⋅ πl

sl = length of the tie bar [cm]

E = modulus of elasticity [N/mm2]

is = radius of gyration of the tie bar

= s

s

IA

[cm]

Is = smallest moment of inertia of tie bar cross section [cm4]

S = safety factor

= 1,4 for λs ≤ 1

= 1,65 for λs > 1

3. Load athwartships

3.1 Amount of load

The force Fq as to A.2. shall be taken to be the load of each container to act upon the cell guide structure.

It may be assumed that 1/4 Fq is transmitted to the cell guide structure through each of the four corner fittings of one longitudinal side wall of the container.

3.2 Cross ties

3.2.1 Cross ties rigidly connected at their ends to the hull

The outer cross tie sections shall be designed for ab-sorbing such compressive and tensile loads as result from half of all stacks of containers placed side by side. Where necessary, a check shall be made to de-termine whether additional compressive and/or tensile loads due to transverse deformations of the ship's hull shall be absorbed by the cross ties.

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–9

B

Page 24: Stowage and Lashing of Containers

3%

������������

��������0�"�����0�5�

Fig. 3.5

The clear effective (buckling) length sK results from:

– For welded connections: sK = 0,7 ⋅ la

– For screw connections and suspended structures: sK = la

The inner cross tie rods may be designed to be weaker according to the loads occurring. Slenderness ra-tio λ ≤ 250.

3.2.2 Cross ties not connected with the hull

The loads acting upon the members of the structure shall be determined by a frame computation (see 1.). The computation for buckling shall be done as indi-cated in 3.2.1.

3%

������������

0

Fig. 3.6

3.3 Vertical guide rails

In case of non-displaceable end and intermediate shor-ing points (see Fig. 3.6), the rails shall be considered, for the calculations, as continuous girders simply supported at both ends. In case of a shoring system as to Fig. 3.6, the total horizontal load acting upon each cross tie is distributed among the vertical guide rails according to their rigidity values

ii 3

1

Ik =l

(In the example, Fig. 3.6, all the lengths li would be the same.)

Load on each rail at the cross tie level:

[ ]ii q

kP P kNk

= ∑ ⋅∑

Σ Pq = total transverse force per cross tie

Σ k = sum of the rigidity values of all vertical guide rails

3.4 Lateral supporting rails

The forces as to A.6. shall be used in the design of these rails.

4. Load fore and aft

4.1 Amount of load

The force Fl as to A.3. shall be taken to be the load of each container to act upon the cell guide structures.

It may be assumed that 1/4 Fq is transmitted to the cell guide structure through each of the four corner fittings of the front or door wall of the container. Reductions due to friction between container layers are not per-missible.

4.2 Longitudinal ties

The effective compressive and tensile loads follow from the load assumption as to 4.1 and the number and arrangement of the longitudinal ties. For compression members the slenderness ratio shall not exceed 250. The true tie length shall be taken for the effective length subject to buckling.

The longitudinal ties shall be so connected to the ship's hull that they will not absorb any considerable compressive and tensile stresses resulting from longi-tudinal bending stresses the ship is exposed to.

4.3 Cross ties

Where the longitudinal forces are to be absorbed by the cross ties only, the same shall be designed to with-stand the bending and shearing stresses occurring. The distribution of the loads acting upon the transverse girder follows from the arrangement of the vertical guide rails.

A load distribution as to Fig. 3.7 throughout the length of the cross tie may be assumed as well.

-���������50��������0�5�0��

*6(7

+

+

+

+

��

��

Fig. 3.7 Load distribution throughout cross tie

Chapter 20 Page 3–10

Section 3 Design Principles I - Part 1GL 2012

B

Page 25: Stowage and Lashing of Containers

5. Vertical load

For the purpose of designing vertical guide rails which also are to support hatch covers or deck parts or simi-lar parts loaded with containers, the loads shall be

determined including the acceleration factor "bv" according to A.4.1.3. The scantlings resulting for the structural members shall not be taken less than those following from the GL Rules for Hull Structures (I-1-1), Section 10, C.

I - Part 1 GL 2012

Section 3 Design Principles Chapter 20Page 3–11

B

Page 26: Stowage and Lashing of Containers
Page 27: Stowage and Lashing of Containers

Section 4

Materials, Welding and Tests

A. Materials and Constructional Parts

1. Manufacture and testing

1.1 Works approval

Materials and constructional parts for cell guides and lashing elements may only be supplied by manufac-turers approved by GL in this respect. Approval shall be applied for in writing to GL and will be granted, as a rule, on basis of an inspection of the works and ap-proval tests of the products. The scope of testing will be laid down in this respect from case to case.

1.2 Requirements for the materials, quality evidence

All materials and constructional parts decisive for the strength of the buttress and cell guide structures as well as lashing elements shall satisfy, in respect of their quality characteristics, the GL Rules for Steel and Iron Materials (II-1-2), be tested in the presence of a Surveyor and be certified by GL according to the GL Rules for Principles and Test Procedures (II-1-1), Section 1, H.1.2 and 3.1 respectively.

Where parts not welded to the ship's hull or not rele-vant for the ship’s strength are concerned, testing by the manufacturer with a certificate according to the GL Rules for Principles and Test Procedures (II-1-1), Section 1, H.1.2, e.g. an acceptance test certificate 3.1 as to EN 10204, may be consented 1.

The material records shall contain specific details on the manufacturing procedure, composition, heat treat-ment mechanical properties and marking.

Relevant equivalent certificates can be recognized.

Inspection of constructional parts:

All parts shall be made available to the Surveyor for an inspection of their surface condition and a dimen-sional check. The dimensional checks and - in case of piece numbers above 100 - also the visual inspection will be carried out at random. On request of the Sur-veyor non-destructive tests are to be carried out, e.g. ultrasonic, x-ray or surface crack indication tests.

–––––––––––––– 1 Lashing elements welded on hull are in general of minor

importance to ship's strength and are normally sufficiently cer-tified by a material certificate 3.1 according to EN 10204 .

1.3 Retests

Where no or insufficient material records are fur-nished for the materials and/or individual parts or if the association with the test certificates is insufficient, GL may call for retests to be carried out under their supervision. The kind and scope of the tests will be laid down from case to case in conformity with the GL Rules for Materials.

1.4 Selection and materials

The selection of materials shall be done taking all qualities into account, a confirmation of GL is done normally by the drawings approval.

1.5 Marking

Materials and fittings shall be marked by the manufac-turer in such a way that an unobjectionable identifica-tion can be done by the material certificates. Materials tested by GL are stamped additionally according to the GL Rules for Principles and Test Procedures (II-1-1), Section 1, F.

Cast steel and forged pieces are to be marked with the manufacturer's ident, short ident of the kind of cast and a marking respect. ident-no. for the charge (i.e. last three numbers of the charge number). Additional markings can be agreed between manufacturer and customer.

2. Approved materials

2.1 Materials for cell guides, blind frames and similar structures

Plates, sections, bars and pipes for cell guides and blind frames, container stanchions and similar struc-tures shall be in accordance with the GL Rules for Steel and Iron Materials (II-1-2), Section 1.

The materials shall fulfil the requirements of the mini-mum impact strength of the rules mentioned before.

Table 4.1 furnishes a summary of permissible GL-shipbuilding steels and comparable steels acc. to EN 10025-2. Steels from other norms may be used if equivalent to those listed in the Table, if it can be proved that they are suitable for welding and if they meet the requirements of the GL Rules for Steel and Iron Materials (II-1-2), Section 1, C.2.3.

I - Part 1 GL 2012

Section 4 Materials, Welding and Tests Chapter 20Page 4–1

A

Page 28: Stowage and Lashing of Containers

Table 4.1 Materials for cell guides, container stanchions and similar structures (excerpt of properties required)

Hull structural steels 1 Comparable structural steels 2

Grade Min. yield point

Tensile strength

Steel quality acc. to

EN 10025-2 and

EN 10025-3

Min. yield point ReH 3

[N/mm2]

Tensile 3 strength

Rm

[N/mm2] [N/mm2] t ≤ 16 mm 16 < t ≤ 40 mm [N/mm2] GL–A S 235 JR

S 275 JR 235 275

225 265

360 – 510 410 – 560

GL-B S 235 J0 S 275 J0

235 275

225 265

360 – 510 410 – 560

GL–D 235 400 – 520 S 235 J2 S 275 J2

235 275

225 265

360 – 510 410 – 560

GL–E S 275 NL 275 265 370 – 510

GL–A 36 S 355 J2

GL–D 36 355 490 – 630 S 355 K2 S 355 N

355 345 470 – 630

GL–E 36 S 355 NL 1 For more requirements, see GL-Rules for Steel and Iron Materials (II-1-2), Section 1.B. 2 Extract from the standards EN 10025-2 and EN 10025-3 respectively. 3 When dimensioning the components, possibly, the lower yield points or tensile strengths – depending on steel quality and/or thickness of

products – have to be considered by increasing the cross sections accordingly.

2.2 Materials for stowage- and lashing fittings above or below weather deck

The steels shall fulfil following requirements:

– The steels shall be killed and fine grain treated.

– All products shall be heat treated, that means normalised or quenched and tempered.

– The steels shall fulfil the requirements for im-pact strength mentioned in the Standards and approved specifications respectively, at least fulfil the requirements mentioned in Table 4.2.

– Unalloyed steels intended for welding shall not have a higher carbon content than 0,22 % (ladle analysis)

– If the type of product requires it, additional non destructive test can be required.

Proof of impact energy is to be given for the tempera-tures at ISO-V specimen.

Table 4.3 gives an overview of the materials to be used for stowage- and lashing fittings.

Use of the grades GL-A, GL-B and S235JR, S235J0, S275JR, S275J0, S355JR respectively and S355J0 (EN 10025-2) according to the GL Rules for Steel

and Iron Materials (II-1-2), Section 1, B. and C. is not permitted.

If stowage and lashing fittings are fabricated from materials according to EN 10025-2 and EN 10025-3 by hot forming, the requirements as regards chemical composition of the GL Rules for Steel and Iron Mate-rials (II-1-2), Section 1, C.2.3.1 are to be observed.

If an impact strength of 14 (11) Joule at – 20 °C is proofed for nodular cast iron of grade EN-GJS-400-18-LT, it can be used for fittings for service above and below deck. Nodular cast iron shall not be used for dynamically high loaded fittings (bottom twist-locks, midlocks etc.).

The temperature at which the necessary impact strength values are proofed is to be chosen with –20 °C for above-deck and with 0 °C for below-deck service.

2.3 Materials for lashing chains

For manufacture of lashing chains preferably fully killed steels (e.g. 21 Mn 5, 27 Mn Si 5) according to DIN 17115 or equivalent steels shall be used. The grade RSt 35-2 may be used after special approval.

Where the material grade and the welding procedure so require, the chains are to be properly heat treated.

Chapter 20 Page 4–2

Section 4 Materials, Welding and Tests I - Part 1GL 2012

A

Page 29: Stowage and Lashing of Containers

Table 4.2 Minimum values of impact energy for stowage and lashing fittings above and below the weather deck

Product from

Impact energy

KV 1 [J]

min

Test temperature for materials with usage above

weather deck

Test temperature for materials with usage below

weather deck

longitudinal transverse [°C] [°C]

Rolled products 2 Remin ≥ 235 N/mm 2

27 (19) 20 (14)

Rolled products 2 Remin ≥ 355 N/mm 2

34 (24) 24 (17)

Forged steels 27 (19) – 20 ± 0

Cast steels 27 (19) Nodular cast iron 14 (11)

1 Obtained from ISO-V-specimens as an average value from three tests. One of these values may occur as the lowest individual value; see data indicated in brackets.

2 Plate, section, bar

Table 4.3 Materials for stowage and lashing fittings

Type of product, standard

Steel- or casting grade

Structural steels acc. to rules for materials of Germanischer Lloyd

GL–D, GL–D 32GL–D 36, GL–E GL–E 32, GL–E 36

General steels EN 10025-2

S 235 J2 +N S 275 J2 +N S 355 J2 +N

Fine grain steels suitable for welding acc. to EN 10025-3

basic qualities (N) tough at sub-zero temperatures (NL)

Cast steel DIN 1681 DIN 17182

GS–38 GS–45 GS–52 GS–16Mn5 GS–20Mn5

High temperature steel castings DIN 17245 GS–C 25

Low-temperature steel castings SEW 685

GS–21Mn5 GS–26CrMo4

Quenched temperature steel castings EN 10083

41Cr4 42CrMo4

Nodular cast iron EN 1563

EN-GJS-400-18-LT

B. Welding

The following summarises the most important quality assurance measures to be observed and/or to be taken during welding. The scope of quality assurance meas-ures is to be brought into conformity with the produc-tion. For any additional requirements having to be imposed the GL Rules for Welding (II-3) and for Hull Structures (I-1-1), Section 19 apply analogously.

1. Conditions in respect of workshops

1.1 Works' approval

Works and shops, subsidiaries and also sub-contractors intending to carry out welding work on container lashing elements shall be approved by GL in this re-spect. The approval is to be applied for at GL head office with the following statements and particulars:

– description of the workshop

– materials used

– welding procedure and consumables

– welding personnel

– test equipment as far as available

1.2 Facilities

The works and shops shall avail themselves of the necessary facilities permitting expert and perfect weldings. Such facilities are, inter alia, working places protected against atmospheric influences, machinery and equipment for an expert preparation of the weld-ing joints, reliable welding machinery and equipment,

I - Part 1 GL 2012

Section 4 Materials, Welding and Tests Chapter 20Page 4–3

B

Page 30: Stowage and Lashing of Containers

stationary or portable drying spaces or cabinets for storing the welding filler metals and consumables.

1.3 Welding jigs

For assembly and welding, it is recommendable to use jigs in order to ensure correct dimensions of the struc-tural parts. The jigs shall be of such a configuration that the weld seams are easily accessible and can be welded in the most favourable position possible (cf. i.a. also 5.1 and 6.5). Tack or temporary weldings shall be avoided wherever possible.

2. Welders, welding supervision

2.1 Welder's qualification test

All welding work on container lashing elements may only be carried out by GL-recognized welders examined in connection with the welding process in question. For manual arc welding and semi-mechnized gas-shielded welding on stowage- or lashing fittings as well as on the hull only welders are permitted, who have qualified according to EN 287 respect. ISO 9606 and, addition-ally, fulfil the GL Rules General Requirements, Proof of Qualifications, Approvals (II-3-1), Section 3.

Welders to be employed for special grade structural steels shall have qualified by analogy with the GL Rules General Requirements, Proof of Qualifications, Ap-provals (II-3-1), Section 3 or in a corresponding quali-fication group as to EN 287 and ISO 9606 respec-tively. Equivalent welder's qualification tests on the basis of other rules or standards may be recognized.

2.2 Welding supervisors

Each workshop carrying out welding work shall have in its employ a welding supervisor whose professional qualification shall be evidenced. Depending on the type and scope of the welding work to be carried out, welding supervision may be effected by, e.g., a weld-ing specialist or a graduate welding engineer. Changes in respect of the welding supervisors shall be commu-nicated to GL without any prior request to do so. The welding supervisor(s) shall responsibly supervise the preparation for, and execution of, the welding work.

3. Welding processes, procedure tests

3.1 Evidence of suitability

Only welding processes shall be used the suitability of which has been proved in a procedure test.

As to welding procedure tests for the flash butt weld-ing and friction welding see Annex B.

3.2 Application, execution

The execution of a procedure test in order to extend the approval according to 1.1 is to be applied for at GL head office with the following statements and particulars:

– description of the procedure and the equipment (if possible also pictures, leaflets or similar)

– particulars of the procedure (preparation of seams, welding data, etc.)

– materials to be welded and dimensions of the parts to be connected

– welding consumables to be used and auxiliaries

– subsequent works, if applicable

– subsequent heat treatment data, if applicable

– intended testing during manufacture

– place and time of procedure testing

Welding of samples and testing is to be done under supervision of GL.

3.3 Scope of testing, requirements, welders

The scope of testing, test pieces and specimens, and requirements will be laid down, by analogy with the GL Rules for Welding in the Various Fields of Appli-cation (II-3-3), Section 1 from case to case in accor-dance with the application range applied for. Welders employed in procedure tests are considered qualified in the welding technique concerned and/or for the respective materials, provided that the procedure tests have been successfully completed. Where further welders or operator groups are to be employed with the procedure application range enlarged later on, the welders or operator groups shall be adequately trained and tested.

4. Welding filler metals and consumables

4.1 Approval and range of application

All welding filler metals and consumables (such as rod electrodes, shielded-gas welding wires etc.) shall have been approved by GL in accordance with the GL Rules General Requirements, Proof of Qualifica-tions, Approvals (II-3-1), Section 5. The required quality grade depends on the base materials to be welded.

5. Design of weld joints

5.1 General principles

The weld joints shall be designed from the beginning in such a way that they be easily accessible during manufacture and can be made in the most favourable welding sequence and welding position possible (cf. also 6.5), care being taken that only the least possible residual welding stresses and distortions will remain in the constructional components after manufacture. Small distances of the welded joints from one another and local accumulations of welds shall be avoided.

Chapter 20 Page 4–4

Section 4 Materials, Welding and Tests I - Part 1GL 2012

B

Page 31: Stowage and Lashing of Containers

5.2 Weld shapes

Butt weld joints (such as I, V or X seams) and corner or cross joints (such as single-bevel butt joints) shall be designed in such a way that the full plate or shape cross section is fused. In order to achieve this, the constructional components shall be prepared with adequately chosen weld shapes as to the standards being given a sufficient angle between the planes of the fusion faces, a sufficient air gap, and the smallest possible depth of the root faces in accordance with the plate thickness. Special weld shapes require GL ap-proval; where necessary, the weld shapes are laid down in connection with a procedure test.

5.3 Fillet welds

Fillet welds shall, in zones of high local stress (i.e. load introductory zones), whenever possible, be so designed as to be continuous on both sides. Only fil-lets continuous on both sides or intermittent fillets shall be provided at especially corrosion endangered parts (i.e. exposed to sea water) where the fillets being led around the stiffener or scallop ends to seal them. The fillet throat depends on the stressing in each case, and proof calculations of its sufficiency shall be fur-nished in cases of doubt. The "a" dimension (throat thickness) shall not exceed 0,7 t (t = thickness of the thinner part) nor be less than 3,0 mm.

5.4 Overlapped welds

Overlapped weld joints (instead of butt-seam connec-tions) shall only be used in connection with structural parts subject to small loads and only be arranged, wherever possible, in parallel to the direction of the main stress. The overlap width shall be at least 1,5 t + 15 mm, as t being the thickness of the thinner plate. The fillets shall be made in accordance with 5.3.

6. Manufacture and testing

6.1 Welding preparation

The constructional components shall be dry and clean in way of the weld. Any scale, rust, flame cutting slag, grease, paint (with the exception of permitted over-weldable production coatings), and dirt shall be thor-oughly removed prior to welding.

Where plates, shapes or constructional components are provided with a corrosion-reducing production coating (shop-primer) prior to welding, this coating shall not affect the quality of the welded joints.

6.2 Assembly

When preparing and fitting together the constructional parts, care shall be taken to meet the specified weld shapes and gap widths (air gaps). Where the permissi-ble gap width is slightly exceeded, the same may be reduced by deposit welding on the fusion faces of the joint. Filling pieces or wires shall not be welded in.

6.3 Alignment of constructional components

Plates and shapes shall be accurately aligned, in particu-lar in structures interrupted by crossing members. A dis-placement of the edges relative to one another of more than 15 % of the plate or shape thickness, but maximum 3 mm, the lesser figure being applicable, is not acceptable.

6.4 Protection against atmospheric influences

During welding operations, the area where work is car-ried out shall be protected against atmospheric influences. In cold air (below 0 °C), suitable measures shall be taken (covering, heating the constructional components) to ensure satisfactory execution of the weld joints. Welding shall cease at temperatures below –10 °C. Any rapid cooling - in particular in the welding of thickwalled parts or steels susceptible to hardening - shall be avoided.

6.5 Welding position and sequence

Welding work shall be carried out in the most favour-able welding position possible. Welding in vertical downward position shall be avoided wherever possible and shall not be applied to connecting load-bearing components, not even after a procedure test for verti-cal downward welding in general and irrespective of the approval of welding consumables. A suitable welding sequence shall be chosen to ensure the least possible restriction of the weld seam shrinkage.

6.6 Workmanship

In welding operations, care shall be taken to achieve uniform penetration, perfect fusion down to the root, and uniform, not excessively convex weld surfaces. In multi-pass welding, slag having originated from the preceding runs shall be thoroughly removed. Cracks (including broken tack welds), larger pores or slag inclusions etc. are not to be welded over but shall be gouged out.

6.7 Repair of defects

The repair of major workmanship defects may only be carried out after consent of GL has been obtained.

6.8 In-shop control

Workmanlike, perfect and complete execution of the welding work shall be ensured by a close control by the works or shop concerned. GL will check the welds at random during fabrication and, where necessary, during the final inspection after completion. GL is entitled to reject insufficiently checked constructional components and require their being tendered a new for inspection after successful in-shop control and com-pletion of any repairs necessary.

6.9 Weld seam testing

GL is entitled to demand additional non-destructive tests to furnish evidence of a satisfactory weld quality, to be carried out on important structural parts. The type and scope of the tests will be laid down by GL from case to case.

I - Part 1 GL 2012

Section 4 Materials, Welding and Tests Chapter 20Page 4–5

B

Page 32: Stowage and Lashing of Containers
Page 33: Stowage and Lashing of Containers

Annex A Instruction for the Performance of Inspections

of Container Lashing Elements

A. Performance of Inspections

1. General

1.1 All components for container stowage and lashing elements are in principle subject to testings in accordance with the following requirements. The testings and inspections required are to be carried out at manufacturers', prior to delivery.

1.2 The scope and type of testings shall comply with the requirements of items 1., 2. and 3. below. Where deemed necessary, deviations therefrom may be admitted upon agreement with GL.

1.3 In general, proofs of materials as defined in item 2. below are to be furnished for the components presented for testing. Where such proof cannot be presented, in agreement with Germanischer Lloyd head office, a subsequent material test is to be carried out. To this effect, the relevant components are to be marked unmistakably.

1.4 Generally with the test the drawings ap-proved by head office have to be presented to the surveyor.

1.5 All components exposed to tension/compres-sion are to be subjected to load tests, see 3. For this purpose, at least 2 % of the items delivered are to be selected and subjected to the test load prescribed to which the component shall be able to resist without cracks or permanent deformations occurring. If the test reveals any deficiencies, the Surveyor may extend the scope of testing at his own discretion. Any defi-cient parts are to be eliminated.

Where a series consists of less than 50 parts, at least one of them is to be load tested. Where a manufacturer repeatedly produces minor series of equal parts at certain intervals, proof of quality is to be furnished by load testing of each individual series.

1.6 The parts to be subjected to the test load to be arranged on/clamped into the test bench in a manner corresponding to onboard conditions.

For fittings which have to be welded-in for the pur-pose of testing and which therefore cannot be used anymore after testing, the scope of testing may be reduced. For this an acceptance test is to be presented, not older than 12 month. Furthermore a type Certifi-cate of GL shall be presented for these fittings.

1.7 Where a lashing element is composed of several components (e.g. turnbuckles, twistlocks) supplied by different manufacturers, testing has to be carried out upon final assembly. For components not subject to load testing, only proofs of materials as defined in item 2. below are to be furnished by the subcontractors.

1.8 In case of doubt, the Surveyor is entitled to have testings carried out beyond the prescribed scope, e.g., additional materials tests.

1.9 Break-load-tests are carried out in conjunc-tion with the type test (see 3.). Break-load-test are to be repeated depending on production numbers upon agreement with the surveyor, however, latest after 5 years.

1.10 Kinds of testings

1.10.1 Testing on a lot basis

In general, testing is carried out by lots, combining into one testing unit elements manufactured by the same process, from the same material and in the same form. The Surveyor will select not less than 2 % of the parts of each lot and check these for their surface finish and accuracy to size and tolerances.

1.10.2 Testing on a piece basis

Where testing on a piece basis is required, e.g. on account of the kind of element, special agreements will have to be reached between manufacturers and GL.

2. Special test

2.1 Cell guides are to be controlled for measure-ments after installation. A function test has to be done as a random check with containers or a corresponding pattern.

2.2 Generally a material-test certificate of a neu-tral institution of the maker has to be presented with the test. Welded-in lashing elements, that are welded into ship structures which are important for ships strength, require a GL certificate. The welded-in plates shall reach at least the characteristic values of the plates where they are welded into. Exceptions have to be agreed upon with GL Head Office.

I - Part 1 GL 2012

Annex A Instruction for the Performance of Inspections of Container Lashing Elements

Chapter 20Page A–1

A

Page 34: Stowage and Lashing of Containers

2.3 Welded fittings have to be randomly checked for welding thicknesses aside of the normal welding seam examination (especially with container founda-tions).

2.4 Welding-in foundations (pots)

All welding-in pots have to be checked for tightness (proof by makers certificate). GL reserves the right to be present at this test. Exceptions shall be arranged with GL head office.

3. Load tests (type test)

The table in Annex C shows working load, test load and breaking load for the most frequent fittings, as well as the test arrangement for the load tests. The stated values are applicable in case the materials which are usual for the specific fitting are used. The test loads are calculated in accordance with the values of the table below and are to be transmitted corre-spondingly onto other fittings.

Container lashing fittings are also approved and tested for lower safe working loads as long as it fits into the system

The number of necessary test- and breaking load tests for the type-test (-approval) will be stated for each fitting with the drawings approval by the GL head office. For standard elements, however, at least three pieces are to be tested with break load.

On completion of the load test, an operational test shall be carried out.

Under the test load no permanent deformations or incipient cracks may occur.

The successfully carried out type test will be certified with a type-certificate by GL Head Office (sample see Annex C).

A load test plus an operational test may be required for lashing appliances consisting of several individual parts the joint performance of which has not yet been proven.

For common designs of fully automatic locks, an operational test is required as described in Annex C. For novel concepts for fully automatic locks, details of the operational test will be individually laid down by GL Head Office.

4. Marking of components

4.1 General

The marking of the fittings is to be done in such a way that an identification on account of the material cer-tificates to be presented is possible. The stamping by the surveyor is done after examination of the material certificates, after visual inspection of the finished product and, if need be, the successful practical test-ing. In order to avoid damages to the component, the

method of fixing the marking may have to be agreed upon with the Surveyor (see 4.3.5 below).

4.2 Marking by GL stamp

4.2.1 Testing on a lot basis

Materials and components tested on a lot basis, which met the test conditions are provided with the GL stamp

4.2.2 Testing on a piece basis

Materials and components tested or inspected indi-vidually in accordance with the Rules and meeting their requirements will be provided with the stamp

4.2.3 Extent of stamping

At random checks all examined fittings are stamped (2 % of the delivery). With individual inspection all parts are stamped.

4.3 Examples for marking of individual parts

4.3.1 Castings are to be provided by manufacturers at least with their symbol and with a marking showing the charge or heat treatment batch. In addition, parts are to be marked as defined in 4.2.

4.3.2 Forgings are to be provided with the manu-facturer's symbol and a marking showing the charge, production or heat treatment batch. In addition, parts are to be marked as defined in 4.2.

4.3.3 Parts made of rolled steels

Stamping is to be done in accordance with 4.2.

4.3.4 Lashing bars

Following the tensile test according to 4.2 each testal lashing bar is to be stamped.

4.3.5 Lashing chains

Following the tensile test each chain is to be stamped at one end according to 4.2. In addition, following testing in accordance with the standards applicable to chains, each chain is to be stamped by manufacturers with their symbol (or identification character) as well as with the grade characteristic of the chain material employed (see DIN 685). In principle, stamping is to be effected on the unwelded side of the chain link and shall not create any deterioration of the link.

Chapter 20 Page A–2

Annex A Instruction for the Performance of Inspections of Container Lashing Elements

I - Part 1GL 2012

A

Page 35: Stowage and Lashing of Containers

4.3.6 Lashing ropes

For marking the nominal strength of the wires, lashing ropes are to be provided with coloured spun in identi-fication threads, as follows:

– nominal strength 1570 N/mm2: red

– nominal strength 1770 N/mm2: green

Ropes tested by approved manufacturers or dealers independently and supplied with GL approved Works

Test Certificates shall additionally be provided with a spun in identification thread carrying the manufac-turer's symbol or the identification No. designated by GL.

Ropes tested in the Surveyor's presence are marked by a lead seal carrying the stamp:

I - Part 1 GL 2012

Annex A Instruction for the Performance of Inspections of Container Lashing Elements

Chapter 20Page A–3

A

Page 36: Stowage and Lashing of Containers
Page 37: Stowage and Lashing of Containers

Annex B Welding Procedure Qualification Test Flash Butt Welding

or Friction Welding of Container Lashing Elements

A. Procedure Qualification Flash Butt Welding

1. Scope and purpose

The present working sheet applies to welding proce-dure qualification tests for flash butt welding or fric-tion welding of Container lashing elements. It sup-plements the GL Rules for Welding (II-3) as well as the "Rules for Stowage and Lashing of Containers aboard Ships" and describes the special test pieces, test specimens and requirements for proof of unobjec-tionable workmanship and adequate mechanical prop-erties of the welding joints.

2. Types of joints, materials, requirements

In accordance with the state of technology and appli-cation the above procedures are mainly employed for joining lashing bars, including their end fittings, such as hooks, eyes etc., made from quenched and tem-pered steels 41 Cr 4 (Mat.-No. 1.7035), 25 Cr Mo 4 (Mat.-No. 1.7218) and 42 Cr Mo 4 (Mat.-No. 1.7225). As a rule their diameters are approx. 25 mm.

In most cases these steels are used in quenched and tempered condition and owing to their chemical com-position are relatively susceptible to hardening. Par-ticularly in the case of flash butt welding embattle-ment of the weld area is to be reckoned with, which can only be compensated by subsequent systematical heat treatment. Therefore, apart from furnishing proof of strength, the main purpose of the procedure test is to furnish proof of adequate toughness (ductility). The welding and, where applicable, annealing data shall be capable of being reproduced.

3. Test pieces and specimens

The test pieces are to be welded from known steels, for which proofs are available. If different materials are employed, the different steels are to be welded to each other and/or welded to each other in the envis-aged combination. All welding and annealing data, if any, including the pertinent machine adjustment char-acteristics, are to be recorded. The length of the test pieces is to be taken such as to enable them to be per-fectly clamped, to exclude heat accumulation and to enable sampling as required. The minimum length of test specimens is 300 mm.

For each kind and/or combination of material(s) in the presence of a GL representative at least six equal test pieces are to be welded, from which following a mag-netic particle or dye penetration test for surfaces flaws the following specimens are to be taken:

– 1 round tensile test specimen according to DIN 50120 Part 2 (diameter of test specimen do = 20 mm)

– 3 transverse bending test specimens according to DIN 50121 Part 2 (cross-section of test speci-men ≈ cross section of component)

– 1 notched transverse bending test specimen analogously to DIN 50121 Part 2 (cross-section of test specimen ≈ cross-section of component)

– 1 macro-etching (longitudinally) with hardness measurements (1 × at specimen centre, 1 × near surface of specimen)

In particular cases GL may stipulate other supplemen-tary examinations (e.g. ultrasonic test) or testings (e.g. of notch impact bending test specimens); in that case the number of test specimens will have to be increased accordingly.

4. Testing and requirements

Testing is to be effected in the presence of a GL repre-sentative subject to the standards mentioned. The tensile strength is to be at least equal to the values fixed for the quenched and tempered condition in the materials' standards for the material concerned. In the transverse bending tests using a mandrel diameter of 4 × specimen thickness, a minimum bending angle of 60° shall be reached. The bending elongation (measur-ing length lo = 2 × specimen thickness) is to be re-ported.

The notched transverse bending test specimen shall not show any welding flaws, such as pores, inclusions, cracks and the like in the broken section. The same supplies to macro-etchings. The hardness survey shall be as even as possible and shall not show any pre-eminent hardness peaks. The requirements for possible additional testings will be fixed from case to case.

5. Recording of results

During the test weldings all parameters essential for the constancy and quality of the weld connections are to be recorded.

I - Part 1 GL 2012

Annex B Welding Procedure Qualification Test Flash Butt Welding or Friction Welding of Container Lashing Elements

Chapter 20Page B–1

A

Page 38: Stowage and Lashing of Containers

In the case of flash butt welding these include:

– Welding machine (kind, manufacturer, type, output, steering mechanism, control devices, etc.)

– Basic material (kind, shape and dimensions)

– Workpiece preparation (clamping and abutting surfaces)

– Length tolerance (overlength) and clamping length

– Clamping jaws (shape and material)

– Clamping force

– Upsetting force and upsetting pressure

– Welding current and platen speed

– Welding time

– Axial reduction of parts length

– Post-heating current and time

– Removal of welding burrs

It is advisable to this effect to equip the welding ma-chine with a device for recording the time curve of current, distance and force.

In the case of friction welding these include:

– Welding machine (kind, manufacture, type, output, steering mechanism, control devices etc.)

– Basic material (kind, shape and dimensions)

– Workpiece preparation (clamping and abutting surfaces)

– Length tolerance (overlength) and clamping length

– Speed (number of revolutions)

– Contact pressure

– Welding time

– Axial reduction of parts length

– Removal of welding burrs

Here, too, it is advisable to record the time curve of relative speed and contact pressure and under all cir-cumstances to equip the machine with relevant control devices.

During the tests the shapes of test specimens and their dimensions, mechanical properties achieved, findings of tests (flaws) are to be recorded and the hardness curves are to be represented graphically. The protocols are to be countersigned by the Surveyor.

6. Literature (selection)

The following technical guides of the DVS (German Welding Society) are German editions only.

DVS 2901-1

DVS 2909-1

DVS 2909-2

DVS 2909-3

DVS 2909-4

DVS 2909-5

DVS 2922

Chapter 20 Page B–2

Annex B Welding Procedure Qualification Test Flash Butt Welding or Friction Welding of Container Lashing Elements

I - Part 1GL 2012

A

Page 39: Stowage and Lashing of Containers

Annex C

Container Lashing Fittings

A. Loads for Container Stowage- and Lashing Fittings

���������

������� ����

������������������

����� ���

������� ��������������� ��

��� ��

������� ��������������� ��

��������� ��

������� ���

���������� ���

���������� ���

!�!"#���

������������

�����������

��$����%������

$������

��&������������ �

������������

'���������(

���� �������� ���

������

�������������

���������

����

������������

���

����

)* ++ ,-*

+* �** **

** .* ,.*

)* ++ ,-*

�* -) , *

.* )�) .**

�* -) , *

** .* ,**

.* )�) .**

.* )�) .**

�* -) , *

)* ++ ,-*

)* ++ ,-*

)* ++ ,-*

�* -) , *

.-* - * /)*

-.* /�. +.*

.* /. ) .

�* -) , *

** .* ,**�����������

�.* �++ )**

0� �1 .0� 1*0�

�1))0��1�0�0�

�� �

2���

�� �

2���

����3����

������

�����������&���&����%�#�"#�����������4��������3����������������������������%� �� 1*$���0�3

� �� %���5 ����4��� �� ��1 ���������� ���������� ����� �� �6����3 ������� �% ��� ��������� ����� �� ��%���� �� ����� $3 ���������� ����������������������������5%����0��%�***�7������3

I - Part 1 GL 2012

Annex C Container Lashing Fittings Chapter 20Page C–1

A

Page 40: Stowage and Lashing of Containers

B. Operational Tests for Fully Automatic Locks

Type Test arrangement and loading scenario Test Load [kN]

Compressive force 1 96

Compressive force 2 35 Fully

automatic locks

Test setup: - The distance between center lines of the corner casting apertures on the test jig

is to be 4 mm less than distance between center lines of the corner casting apertures on the test platform.

����8��,44

��������%�4

.944 Loading scenario:

- First, the test jig is to be shifted in the direction of racking force as far as possible within the clearance of the locks.

- Subsequently, test forces are to be applied in the following sequence: a. Compressive forces 1 and 2 b. Racking force

:�4�����&�%� �� :�4�����&�%� �

����8��#� ����%� �

Racking force 210

Compressive force 350

Racking force 150 Fully automatic locks

Test setup: - The distance between center lines of the corner casting apertures on the test jig

is to be 5 mm less than distance between center lines of the corner casting apertures on the test platform.

����8��.44

��������%�4

.944 Loading scenario:

- First, the test jig is to be shifted in the direction of racking force as far as possible within the clearance of the locks.

- Subsequently, test forces are to be applied in the following sequence: a. Compressive force b. Racking force c. Lifting force

:�4�����&�%� � ��%����%� �

����8��#� ����%� �

Lifting force 275

Notes: 1. Two ISO top corner fittings in mint condition are to be fixed on the test platform. 2. A stiff test jig, linking two ISO bottom corner fittings in mint condition, is to be used. 3. The top and bottom apertures of all ISO corner fittings are to be exactly 65 mm wide.

4. The orientation of the racking force is to be always opposite to the nose of the fully automatic lock. 5. During the sequential application of test forces, the previously applied forces are to be kept constant. 6. Devices for application of test forces shall not laterally jam the test jig. 7. Permanent deformations, incipient cracks, or failure of the lock as such will not be accepted. 8. At least three randomly selected fully automatic locks are to be tested.

Chapter 20 Page C–2

Annex C Container Lashing Fittings I - Part 1GL 2012

B

Page 41: Stowage and Lashing of Containers

Annex D

Approvals of Computer Software for Determination of Forces in the Lashing System

A. Approval of Lashing Computers/Software

1. General remarks

A lashing program is computer-based software for calculation and control of container securing arrange-ments in compliance with the applicable strength requirements. Germanischer Lloyd (GL) recommends the installation and the approval of a lashing program for each vessel carrying containers.

GL examines and approves upon request calculation programs on test condition basis. This examinations and the corresponding approval are done in relation to a specific ship.

GL recommends using the lashing program on a GL type approved hardware only. If it is not the case, the program should be installed on two nominated com-puters equipped with separate screen and printer.

2. General requirements

For each vessel the printouts of the test conditions, a copy of the program and a user’s manual have to be sent to the GL Head Office for examination. Test conditions of different bays shall include the following cases:

− twistlocks only

− complete lashing

− with exceeding of stack weight

− with exceeding of lashing load

− with exceeding of lifting force

− an example with outboard stacks missing

− one example, where 20' and 40' containers are arranged in mixed stowed

− typical stowage in hold

The software has to be user-friendly, with a graphic presentation of the container arrangement. It has to reject input errors from user. For example or negative weight input, container positioned outside or lashings, which are not possible on board are not to be accepted. The software and the stored characteristic data are to be protected against any erroneous use.

GL has to be informed immediately about any modifi-cations which may affect the approved lashing pro-gram installed on board of the ship. GL will decide about a re-approval case by case. Failure to advice of any modifications will annul the issued certificate.

The following details have to be given for each con-tainer arrangement in addition to the GM Value of the ship:

− position of each stack

− container weight

− actual stack weights

− permissible stack weights

− lashing arrangement

− transverse acceleration of each stack

− racking forces

− lifting forces

− lashing forces

− corner post loads

− pressure loads at bottom

− percentage of exceeding

− a warning has to be given if any of the strength limit is exceed

The lashing program certificate, the approved test conditions and the user’s manual have to be kept on board.

I - Part 1 GL 2012

Annex D Approvals of Computer Software for Determination of Forces in the Lashing System

Chapter 20Page D–1

A

Page 42: Stowage and Lashing of Containers
Page 43: Stowage and Lashing of Containers

Annex E

Weights, Measurements and Tolerances

Table E.1 Weights, measurements and tolerances

ISO Max. External dimensions Distance between centres of holes in corner fittings

designation of

container

permitted gross

weight

[kg]

Length L

[mm]

Height H

[mm]

Width W

[mm]

Lingitudi-nally S

[mm]

crosswise P

[mm]

Permitted difference

d 1 of diagonals

[mm]

Permitteddifference

d 2 of diagonals

[mm]

1 AAA

1 AA

1 A

1 AX

30.480 12192 100. −

2 896 50.

**

2 591 50. −

2 438 50. −

< 2.438

2 438 50. −

010990.11 −

04259.2 − 19 10

1 BBB

1 BB

1 B

1 BX

25.400 9125 100. −

2 896 50.**

2 591 50. −

2 438 50. −

< 2.438

2 438 50. − 8 923 10

0. − 04259.2 − 16 10

1 CC

1 C

1 CX 24.000

06058.6 −

05591.2 −

052.438 −

< 2.438

05438.2 −

5 854 60. −

04259.2 − 13 10

1 DD

1 D

1 DX

10.160 2 991 50. −

2 591 50. −

2 438 50. −

< 2.438

2 438 50. − 2 788 5

0. − 04259.2 − 10 10

1 Allowable difference of the diagonals of whole-center of the corner castings of bottom and roof areas and side walls. 2 Allowable difference of the diagonals of hole center of the corner castings of front walls, see following sketch. ** In certain countries there are legal limitations to the overall height of vehicle and load.

I - Part 1 GL 2012

Annex E Weights, Measurements and Tolerances Chapter 20Page E–1

Page 44: Stowage and Lashing of Containers
Page 45: Stowage and Lashing of Containers

Annex F

Container-Dimensions

��������������������������������

�����

������������������������������� !��"������#

�$

%

�������&� �����'������� ������(��� ���!� �������) �& ���'���� ����'���� ��#������&��(��(�����&��'� �� �'�����*��+��������,

- ./� � ���� 0.(��1�*�

23���������'(�4

���2$$�����4

���2$�������4

�5���$���2�5%������4

��2$������4

���

2$�%�����4

���2$�$�����4

����63�2$�$�����4

��������2$�$�����4

��������������2$�$�����4

���2$�����4

���2�$�����4

����27�����42%������4

�5���2�5�����4

��� ����$���2���$���4

����������

����������

���2���$���4

����$���

2������4

����

����$���

2������4

�2������4

����

������� �������

�������

�2������4

���

� �

���2������4

���89����2�������� ���$���4

�������

2�����4

� ����

����

:(��8�����������&��(������63������8� 8�;�8�'������� ��;���� ��# ������� <9

������

�����

�����

I - Part 1 GL 2012

Annex F Container-Dimensions Chapter 20Page F–1

Page 46: Stowage and Lashing of Containers
Page 47: Stowage and Lashing of Containers

Annex G

Code of Container Position

����������

����

�����

�� �� � � � � � �� �� �� �

�� � � �� �� ���� �

���� �

��

�������������

����

�������������

��

�� �� �� �� � �� �� ��

��� ��

���� �� �� � �� �� ��

��� ��

�� ��

�� �� �� �� � �� ��

� �� ��

�� ��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

���� �� �� � �� �� ��

��� ��

�� ��

�� ��

��� �������� ��������������������������������������������� ���!"#���� ���$�##�����%

I - Part 1 GL 2012

Annex G Code of Container Position Chapter 20Page G–1

Page 48: Stowage and Lashing of Containers
Page 49: Stowage and Lashing of Containers

Annex H

Height Tolerances of Container Foundations

� �

� �

���

� �

���

�� ��������

� ��������� ����� ���� ��������� ����� ����

������������������������� ���������

�������!"��!������������ ���������

����������������������������������������������

�������������������������������

������������ ��#����$����������%�!� �"�����&��'� �

()�*

��+* ��+*,�

-(-�(

.�#����%��/����

0 �!�#�������������&����"���������������������$�� ���������������������������$�� ������

0���!"��!�1-� ������!���#����%�2�� ���� ��!������

3������������41�����������#����%�� ����

�������

�������

���%����

����!"��!�������%����

��������#����%�� ����

��������#����%�� ����

.�#����%�� ����

I - Part 1 GL 2012

Annex H Height Tolerances of Container Foundations Chapter 20Page H–1

Page 50: Stowage and Lashing of Containers
Page 51: Stowage and Lashing of Containers

Annex I

Maximum Allowable Forces on ISO-Container

������

������

������

������

������

������

��� �� �������������������

������

������

������

������

������

������

������

������

�������������

������ � ������� �� ���!����������"# ���� ��!� ��� ��$ �� � �����"# ���� ��!� ���

������

������

%��

&���

'�����

������

(##� ��� �� �������

������

������

%��

&���

'�����

'�����

��)� ��� �� �������

I - Part 1 GL 2012

Annex I Maximum Allowable Forces on ISO-Container Chapter 20Page I–1

Page 52: Stowage and Lashing of Containers
Page 53: Stowage and Lashing of Containers

Annex J

Determination of the Existing Stack Weight for Mixed Stowage (20' and 40' Container) for the Individual Foundation Points

��� ����

��������

��������

��������

��������

��������

��������

� � �����������

��������

� �����������������

� � ������������

� � ����������������

� ����������������� ���

��!"#$%���"$���$%� ���������������&��$��&�����������!"'������"$���$�'(����!"#$%���"$����$%�������&����������!"'������"$���$�')

I - Part 1 GL 2012

Annex J Determination of the Existing Stack Weight for Mixed Stowage (20' and 40' Container) for the Individual Foundation Points

Chapter 20Page J–1

Page 54: Stowage and Lashing of Containers