Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Model SPSpiral Pipe
Model STSpiral Tees
Model SCStack Caps
Model SNSpiral Nineties
Please see page 2 for Flexible Duct Connectors
SPSA Series Spiral Pipe Stack
AssembliesFresh Air Intake Spiral Pipe, Fittings,
Anchors & Support AccessoriesTechnical Bulletin SPSA TB-R0 © 03.09.2018
Environmental ControlUnit Accessories
General DescriptionModel SPSA Spiral Pipe Stack Assemblies are formed from a combination of Model SP Spiral Pipe, Model ST Spiral Tees, Model SN Spiral Nineties and Model SC Stack Caps, along with a host of critical accessories to provide seals, flexible connections and structural support for the complete stack assembly. When combined as required, these products provide economical fresh air intakes for Bebco Pressurization Units, Ventilation Units, Air Conditioners and Gas Phase Filtration Units, to acquire air from a source above any concentration of flammable, toxic or corrosive vapors that are above acceptable levels of concentration at ground level.
Spiral pipe and fittings are available in 8” to 24” standard and custom diameters in 16 or 20 gauge galvanized steel, 304 Grade stainless steel or 316 Grade stainless steel materials. Galvanized material may feature no finish, a hot dip galvanized finish or an exterior surface urethane finish. Stainless materials may feature no finish or an exterior surface urethane finish. The bodies of all fittings are seal welded. Flanges on galvanized spiral pipe and fittings can be seal-welded or tack-welded and sealed by marine grade calking or a hot-dip galvanized finish. Flanges on stainless spiral pipe and fittings can be seal-welded or tack-welded and sealed by marine grade calking.
SP Spiral PipeModel SP Spiral Pipes are fixed-length spiral pipes that are machine formed from 6” wide spooled metal into the desired diameter and length. The Spiral Pipes feature fixed flanges at both ends and are available in standard lengths of 2, 4, 6, 8 and 10 feet. In addition, upon special order, custom lengths may be provided not exceeding 168 inches (14’), and all spiral pipe is provided within length tolerances of ± .25”.
ST Spiral TeesModel ST Spiral Tees are intended for self-supporting stack applications, by providing a top end connection point for intake air, a branch connection point for inlet air to a Bebco Unit, and a bottom end connection point which is typically fitted with a blind cover plate and used for connection to a stand pipe. The run (end) connections feature seal-welded flanges and the branch (center) connection features a rotating Vanstone flange.
SN Spiral NinetiesModel SN Spiral Nineties are elbow fittings that form 90 degree right angle connections between other stack parts. The Model SN features a seal-welded flange on one fixed flange and one rotating Vanstone flange. For angles other than 90 degrees, see Model FDC Flexible Duct Connectors on Page 2.
SC Stack CapsModel SC Stack Caps prevent rain, debris and large insects or birds from entering the stack, and are required for all stack assemblies. They feature a fixed flange, domed cap and side rain guard, along with a 3/4” x 13 gauge expanded metal screen.
An economical fresh air intake solution to meet your unique
application requirements!
Spiral Pipe in any length,
up to 168 inches!
Stack Diameters ranging from8-24 inches!
Galvanized,Hot-Dip
Galvanized, 304 or 316 Stainless
Steel Materials!
Ask about our Licensed P.E.
Services available tocertify all installations!
Copyright © 2018 - Bebco Environmental Controls Corporation BECC-SPSA-TB-R0 Page 2 of 4
Model GBK Gasket and Bolt Kits provide a seal between spiral pipe and fittings or blind flanges within the hazardous area. The kit includes a die-cut 1/8” close cell neoprene gasket with pressure sensitive adhesive on one side and zinc plated, 304 Grade stainless steel or 316 Grade stainless steel bolt hardware. They are available in 8” to 24” or custom diameters, but not required for Unit intake air ports.
Model GBKGasket & Bolt Kits
Model GBKGasket & Bolt Kit
Model SPAK Spiral Pipe Anchor Kits secure spiral stack bases to a concrete slab, and include eight (8) 3/8” or eight (8) or twelve (12) 7/16” anchors. The Anchor Kits are offered in zinc plated, 304 or 316 Grade stainless steel and include one (1) stud, one (1) anchor body, two (2) nuts, two (2) flat washers and one (1) lock washer.
After setting all anchor and studs, stacks can be secured by threading a nut onto each stud, followed by a flat washer, the stack base flange, a flat washer, a lock washer and another nut to secure the stack. Adjustments can then be made to level the stack. The space under a stack flange can be back-filled with grout or left open for drainage if a blind cover is used to seal the stack, as described below.
Model CAGK Concrete Anchor Guy Wire Kits and Model EAGK Earth Auger Guy Wire Kits are intended to provide wind load support to spiral pipe stack assemblies. Due to the lighter-weight construction of a spiral stack, guy-wires are mandatory, particularly in areas where high wind velocities might occur.
The kits feature three (3) galvanized or stainless steel cables in 40 feet or custom lengths, rated for working loads ranging from 2,400 to 3,900 lbs, to withstand gale force winds up to 150 m.p.h.
The cables are offered in three distinct styles, identified as “GSE” for extra high strength (low flexibility) galvanized guy-wire cable, “GSP” for highly flexible galvanized aircraft cable or “SSP” for highly flexible stainless steel aircraft cable.
Cable hardware for each cable style, comprised of matching materials, include six (6) wire rope thimbles, twelve (12) wire rope clamps, three (3) screw pin shackles, three (3) turnbuckles and three (3) 60° angle flange brackets with bolts.
Model CAGK Kits include three (3) 1/2” x 8” wedge anchor bolts and three (3) eye nuts for anchoring in suitable concrete slabs, while Model EAGK Kits include three (3) 1” x 66” auger screws for anchoring in properly stabilized soil.
Model BC Blind Covers are formed from 16 or 20 gauge galvanized steel, 304 Grade stainless steel or 316 Grade stainless steel disks to seal the base of spiral pipe stack assemblies and prevent the entrance of hazardous gasses or vapors. These covers are typically installed between a custom stand pipe and tee of a stack assembly, as shown on Page 3.
Model SPAKSpiral Pipe Anchor Kit
Model CAGKConcrete Anchor Guy Wire Kit
Model EAGKEarth Auger Guy Wire Kit
Model SPSK Spiral Pipe Stanchion Kits provide an alternate securing method to Guy Wire Kits for Spiral Pipe Stack installations. The Model SPSK consists of 4 major components, including two (2) Model SRMB Stanchion Roof Mounting Brackets, two (2) Model SSMB Stanchion Stack Mounting Brackets, two (2) Model SPSB Spiral Pipe Stanchion Braces in Fixed or Telescoping Styles and one (1) Model SMHK Stanchion Mounting Hardware Kit.
Model SPSK components are available in 304 grade stainless steel with natural or painted finishes, and are certified to withstand gale force winds not exceeding 130 MPH.
The Stanchion Stack Mounting Brackets are provided in a range of diameters to fit 8” to 24” stacks and roof mounting brackets and stanchion braces are provided in a common size.
Model SRMBStanchion Roof
Mounting Brackets
Model CAGK & EAGKGuy Wire Kits
Model SPSKSpiral Pipe Stanchion Kits
Model SPAK Spiral Pipe Anchor Kits
Model BC Blind Covers
Model SSMBStanchion Stack
Mounting Brackets
Model FDC Flexible Duct Connectors provide flexible connections between a stack and Bebco Unit, to simplify installation and eliminate torsional stress between the stack and unit connection.
Model FDC includes two (2) 16 gauge galvanized, 304 or 316 grade stainless steel flanges, two (2) 18-8 stainless steel duct clamps and one (1) 10” to 24” variable length neoprene coated polyester fabric duct, featuring an embedded galvanized steel reinforcement helix, with flexibility exceeding 90 degrees.
Model FDCFlexible Duct Connector
Model SPSBSpiral Pipe
Stanchion Braces
Model SMHKStanchion Mounting
Hardware Kit
Model FDC
Flexible Duct
Connectors
Model SPAKSpiral Pipe Anchor Kit
Building Foundation
Bebco Pressurization Unit
Model GBK Gasket & Bolt Kit
Model ST Spiral Tee
Model SP Spiral Pipe
Typical Stack Installation for BebcoWall Mount Pressurization Unit
8" to 18" StackFlange Pattern
Model GBK Gasket & Bolt Kit &Model BC Blind Cover
20" & 24" StackFlange Pattern
Custom Stand Pipe
Stack Mounting Slab
Model GBK Gasket & Bolt Kit &Model FDC Flex Duct Connector
Product & Flange Dimensions (in inches) & Flange Bolt Quantity Size A B C D E F G QTY 08” X” X X X 11.500 45° .375”Ø 8 10” X” X X X 11.500 45° .375”Ø 8 12” X” 24” 13” 18” 13.8125” 45° .375”Ø 8 14” X” X X X 15.8125” 45° .4375”Ø 8 16” X” 32” 16” 24” 18.125” 45° .4375”Ø 8 18” X” X X X 20.125 45° .4375”Ø 8 20” X” 40” 19” 30” 22.125” 30° .4375”Ø 12 24” X” 48” 22” 36” 26.125” 30° .4375”Ø 12
Product Weights (in pounds)BC CAGK EAGK GBK SC SN SP SPAK ST SPSK 5 25 47 2 X X X 5 X X 5 25 47 2 X X X 5 X X 6 25 47 2 42 48 108 5 43 X 7 25 47 2 X X X 5 X X 8 25 47 2 53 65 150 6 56 X 9 30 52 3 X X X 6 X X 10 30 52 3 61 93 186 7 84 X 12 30 52 3 84 129 224 8 110 X
Copyright © 2018 - Bebco Environmental Controls Corporation BECC-SPSA-TB-R0 Page 3 of 4
DETERMINATION OF CUSTOM STAND PIPE HEIGHT Custom stand pipes provide support for stack assemblies from a stack mounting slab up to the bottom of a stack tee fitting (see above illustration). A measurement from a stack mounting slab to the center of a Bebco Unit’s intake stack connection must be derived to determine stand pipe length, represented as “M” in the illustration above. Dimension D for a selected Model ST Stack Tee must then be deducted to establish a stand pipe length.
IMPORTANT NOTE: Bebco recommends subtracting at least one additional inch to provide adequate clearance for stack leveling nuts or shim washers.
Approximate Product Dimensions & Weights
Model SPSKSpiral Pipe Stanchion Kit
Installation DetailsStack Flange
Shackle Brackets24” Maximum
from Topof Stack Cap
10 FootPipe Section
10 FootPipe Section
StackCap
30 DegreeMinimum Angle
SideView
GradeElevation
120 Degree AngleBetween Cables
(minimum 135-90-135 angles)
Top View
Concrete orEarth Anchors
Supportas required
Upper StackMounting Bracket
48” Maximum fromTop of Stack Cap
Lower StackMounting Bracket
24” Maximum from Upper Bracket
30Degree
MinimumAngles
45 DegreeMinimum Angle
Between Stanchions
Top View
SideView
Roof MountingBrackets 10 Foot
Pipe Section
10 FootPipe Section
StackCap
Supportas required
Model CAGK & EAGKConcrete Anchor & Earth Auger Guy Wire Kit
Installation Details
IMPORTANT NOTE:Installers must provide adequate stack support and anchoring systems. Installers assume all liability for the installation and integrity of said systems,
and should ensure that stack support and anchoring systems are capable of withstanding local inclement weather conditions.
Model SC
Model SN
Model ST
B
A
C
D
B
D
B
E
E
F
FG - Bolt Hole Diameter
M
Copyright © 2018 - Bebco Environmental Controls Corporation BECC-SPSA-TB-R0 Page 4 of 4
Material Specifications Model Number Matrix
Critical Stack Installation Considerations
IMPORTANT NOTES ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.WARRANTY & LIABILITY POLICIES AVAILABLE UPON REQUEST..
Model SP Spiral Pipes, ST Spiral Tees, SN Spiral Nineties, SC Stack Caps & BC Blind Covers Pipe & Fitting Bodies: 16 or 20 Gauge Galvanized Steel, 304 or 316 Grade Stainless Steel Sheet MetalPipe & Fitting Flanges: 1/4” or 3/16” Galvanized Steel, 304 or 316 Grade Stainless Steel Roll-Formed AngleCap Screens: 3/4” x 13 Gauge Galvanized Steel, 304 or 316 Grade Stainless Steel Expanded MetalBlind Covers: 16 or 20 Gauge Galvanized Steel, 304 or 316 Grade Stainless Steel Sheet Metal
Model GBK Gasket & Bolt KitsFlange Gasket: 1/8” Die-Cut Close Cell Neoprene w/ Pressure Sensitive Adhesive on One SideNuts, Bolts & Washers: Zinc Plated Steel, 304 or 316 Grade Stainless Steel
Model FDC Flexible Duct ConnectorsPipe Flanges: 16 Gauge Galvanized Steel, 304 or 316 Grade Stainless Steel Roll-Formed AngleDuct Clamps: 18-8 Grade Stainless Steel Adjustable Tension BandFlexible Duct: Neoprene Coated Polyester Fabric Duct w/ Embedded Galvanized Steel Helix
Model SPAK Spiral Pipe Anchor KitsAnchor Bodies, Studs, Nuts, Flat & Lock Washers: Zinc Plated Steel, 304 or 316 Grade Stainless Steel Anchor Rating: 1,000 Lbs. Shear Force in 4000 PSI Concrete
Model CAGK Concrete Anchor & Model EAGK Earth Auger Guy Wire KitsCAGK & EAGK Wind Load Ratings: 150 MPH Gail Force Winds (non-certified) GSE Cable: 3,900 Lbs. 3/16” 7 Strand Galvanized Steel Extra High Strength Wire GSP Cable: 2,800 Lbs. 3/8” 7 x 19 Galvanized Steel Aircraft CableSSP Cable: 2,400 Lbs. 3/8” 7 x 19 304 Stainless Steel Aircraft CableThimbles, Clamps, Shackles, Turnbuckles, Oval Eye Nuts & Flange Brackets: Galvanized Steel, Zinc-Plated Steel or 316 Grade Stainless SteelCAGK Concrete Anchors: 2,200 Lbs. 3/4” Ø x 10” Long Zinc Plated Steel or 18-8 Grade Stainless SteelEAGK Earth Augers: 6,000 Lbs. 1” Ø x 66” Long Hot-Dip Galvanized Steel w/ 8” Ø Helix
Model SPSK Spiral Pipe Stanchion KitsSPSK Wind Load Rating: 130 MPH Gail Force Winds (certified) Fixed or Telescoping Stanchion Braces: 10’ to 20’ Length x 2” Square x 1/4” Thick 304 Stainless Steel TubingBolts, Nuts, Flat & Lock Washers: 3/8”-16 x 2” Bolt, 3/8”-16 Nut,18-8 Stainless SteelStanchion Roof Mounting Brackets: 1/4” Seal-Welded 304 Grade Stainless Steel Plate Stanchion Stack Mounting Brackets: 12 Gauge 304 Grade Stainless Steel Sheet Metal
Model SPSP - 12 - 120 - 16G - T0
Series Model Number SP - Spiral PipeStack Pipe DiameterXX - 08, 10, 12, 14, 16, 18, 20 or 24 InchLength (in inches)XXX - Specify as 3 digits, not exceeding 168 *Body Gauge & Material16 - 16 Gauge G - Galvanized Steel20 - 20 Gauge S - 304 Stainless Steel X - 316 Stainless SteelFlange Attachment & Stack FinishT - Tack-Welded 0 - None S - Seal-Welded 1 - Hot-Dipped ** 2 - Exterior Urethane
Models ST, SN, SC & BP ST - 12 - 16G - T0Series Model NumberST - Spiral Tee SC - Stack CapSN - Spiral Ninety BC - Blind CoverCorresponding Stack Pipe DiameterXX - 08, 10, 12, 14, 16, 18, 20 or 24 InchBody Gauge & Material16 - 16 Gauge G - Galvanized Steel20 - 20 Gauge S - 304 Stainless Steel X - 316 Stainless SteelFlange Attachment & FinishT - Tack-Welded 0 - None S - Seal-Welded 1 - Hot-Dipped ** 2 - Exterior Urethane
Models GBK, FDC & SPAK GBK - 12 - GSeries Model NumberGBK - Gasket & Bolt KitFDC - Flexible Duct ConnectorSPAK - Spiral Pipe Anchor Bolt KitCorresponding Stack Pipe DiameterXX - 08, 10, 12, 14, 16, 18, 20 or 24 InchBolt / Flange MaterialG - Zinc Plated Steel / 16 Gauge Galvanized SteelS - 304 Grade Stainless SteelX - 316 Grade Stainless Steel
Models EAGK & CAGK EAGK - GSE - 40Series Model NumberEAGK - Earth Auger Guy Wire KitCAGK - Concrete Anchor Guy Wire KitCable Style (with matching hardware)GSE - Galvanized Steel Economy (guy-wire cable)GSP - Galvanized Steel Premium (aircraft cable)SSP - Stainless Steel Premium (aircraft cable)Cable Length40 - Specify in Feet (40 feet is standard length)
Model SPSK SPSK - 12 - 120F Series Model NumberSPSK - Spiral Pipe Stanchion KitCorresponding Stack Pipe DiameterXX - 08, 10, 12, 14, 16, 18, 20 or 24 InchStanchion Brace Fixed or Telescopic Length 120F - In inches, with “F” for Fixed or “T” for Telescopic
IMPORTANT NOTES: Model SP Spiral Pipe available in custom diameters, lengths and gauges.Model EAGK & CAGK Cables and SPAK Stanchion Braces available in custom lengths.Please specify urethane finish color at time of order.Marine Grade Calking applied to all tack-welded flanges unless a Hot-Dip Galvanized Finish is selected.Hot-Dip Galvanized Finish or Stainless materials and seal welded flange construction recommended for highly corrosive or off-shore environments.* Use a leading “0” if needed to indicate stack pipe length in whole inches, such as “020” to indicate 20 inches.** Hot-Dip Galvanized Finish not available for 20 gauge or
stainless steel materials.
Typical Stack Installation for BebcoWall Mount Pressurization Unit
Typical Stack Installation for BebcoWall Mount Air Conditioner
NFPA Code 496 mandates a stack height as required to attain a source of fresh air,
containing no more than trace amount of ignitable gases or
vapors.
Bebco recommends an offset of the stack assembly using a Model FDC Flexible Duct
Connector, to permit proper air flow and access of condenser
compartment components located within wall mount air
conditioners.
Offsets may also be required to clear building eves or other items overhanging a building!
Top View
Side View
Top View
Side View
Custom Stack Configurations
Spiral stacks can be easily configured to provide a source of fresh air to multiple Pressurization or Air Conditioner Units, or attain fresh air from the underside of
offshore platforms or adjacent safe areas.
Ask a Bebco Sales Associate for more information about these options!
Multiple Units
Offshore Platforms
Adjacent Areas (with field supported
or free-standing ends)