Soak Cordura Brochure

Soak Cordura

Soak Cordura BrochureRelease 1.2December 2009

PREMIUM CORDED FABRIC WALLSwww.anutone.com/fabrics.htm

New fo

r 201

0

Size Zer

o!

Accessories NRC for 20mm

Mounting System accessories CorduraStandardA H-Spline 0.50C25 A + Strut™ CC25 + Synth™ AW 10x25 0.78OthersD25 A + Strut™ CC25 0.63D50 A + Strut™ CC50 0.72C50 A + Strut™ CC50 + Synth™ AW 10x50 0.90

Visual VariantsThe visual variants of Soak Cordura are realised fromorientation of the fabric colours. The fabric colours can beinstalled in singles or double combos - pastels, darks orcontrasts.Current standard fabric colours include: (See page 4)• Calypso • Skye • Porcelain• Simba • Spearmint • Sanz• Blaze • Lime • Wasabi• Avocado • Jade • Myst

Design Considerations• The longer edges of the panels can be oriented

horizontally or vertically to make a space look visuallylonger or taller.

• Indicated panel thickness is for base panel only. 3 mm offabric thickness and 5 mm of Z-Clip or H-Spline systemshould be added to overall Soak thickness. Hence, 10mm panel means 18 mm system thickness post-install.For true 10mm only go for Slim PNS or Slim Compo!

• Panels should not touch the floor but rest on Sonatorwooden skirting which may be repeated at the wall-ceilingjunction.

• Panels must be fitted in modules that are dimensionedin multiples of 600mm to avoid field cutting.

Product considerationsFabric shade may vary from batch to batch due tolimitations in dye technology. Butt jointing of differentbatch numbers is not recommended.

Key AttributesAnutone premieres the all-new Soak Cordura for 2010 andbeyond ... bringing Size Zero in fabric-wrapped panels tointerior spaces!Panels can be as slim as 10mm and hung on walls to beaccessed at any point. No longer do Soak panels need tobe bulky and be accessed from one corner onwards.Soak Cordura features corded non-wovens that offercontemporary colours for classy interiors and brings• productivity and privacy of modern workplaces• demanding performance of special venues like auditoria

Added feature is high impact resistance, making SoakCordura rugged and durable for any interior use.

Typical ApplicationsSoak Cordura is used for wall panellings and combo partitionsin architectural spaces listed below. See page 7 for details.

- office conference rooms, meeting rooms- auditoria- cinema multiplexes- classrooms & libraries- hotel banquet halls & corridors- studios- home theatres

AestheticsFabric walls with neat panel joint lines, vertically andhorizontally, for a true panel effect. The edge profile is pencilradius due to the fabric lamination. Soak Cordura featuresthe ‘ribbed’ look.

Additional FeaturesSoak Cordura offers and additional and useful feature oftackable surface for pin-ups.

AccessibilitySoak Cordura 10 & 15mm thick with Z-Clip for any pointaccessibility. 20mm & above with H-Spline for corner pointaccessibility ensure easy dismantling and reinstallation.

Environmental ImpactSoak Cordura is an eco-friendly product and wins GBC’s15 LEED points for green buildings, a ‘Sustain’ effort fromAnutone®.

Features

• Volume density (base panel) - 400 kgs/m3

• Sizes - Width 600mm; Lengths 1200 for 10mm & above,2400mm for 20mm & above

• Thickness (base panel, add 8mm for system thickness)- 10 / 15 / 20 / 25 / 30 / 40 / 50mm

• Edge profiles - Square for 10 & 15mm thickness; Squarewith long edges kerfed for H-spline for 20mm & above

• Fabric returns - Fabric is returned and bonded alongall edges for 10 & 15mm. Fabric is returned andbonded along the short edges and returned andbonded upto the H-spline groove for the long edgesfor 20mm & above.

Soak Cordura

2

NEW

NEW

EconomicsSoak Strand Cordura 10mm thick with Z-Clips or 20mmthick on H-Spline is techno-commercially economical forthe lifecycle cost of the system.

Warranty10 years limited warranty - on the assembled system wheninstalled to Anutone’s specifications and maintained asper instructions.

Logistics - Panel

Thk (mm) Nos./carton Carton wt (kgs) Carton ht (mm)10 10 40 16520 06 44 16525 06 54 17540 04 60 17550 03 51 165

Note - Carton size 1216 x 616 mm. Carton weight is for SoakStrand Cordura only. Soak VDH Cordura will be lighter. SoakBurl Cordura will be heavier. Minimum order quantity - 1 carton.

Variants by SubstratesAnutone's unique AcoustCombi™ technology, variablesound absorption, is realised from substrate variants• Soak Strand Cordura – base panel natural surface for

mid and high frequency sound absorption for allapplications

• Soak Burl Cordura – blinded surface suitable for low-frequency sound absorption and high-frequency soundreflection for for variable acoustics and extended bassresponse in banquet halls, auditoria, cinema, studios,home theatres etc

The AcoustCombi technology works very well with Size Zeropanels of Soak Cordura.

Variants by Core (does not apply to Size Zero)For Noise Isolation, technical variants are realised fromthe core material - the Soak Septum Series –

• Soak Septum Cordura

• Soak Septum T1/T2/T3 Cordura

in all applications where sound absorption and noise isolationis required, especially offices, studios, home theatres etc

Tech Performance - Base Panel• Non-combustibility - Mass loss 53% @ 750oC - ISO 1182

• Ignitibility – ‘P’ - BS 476 Part 5

• Fire Propagation Index – 5.17 - BS 476 Part 6

• Surface Spread – Class I - BS 476 Part 7

• Specific Optical Density of Smoke

- Flaming Exposure 26.28 Dm (Corr) - ASTM E662

• Thermal Conductivity – 0.08 Wm/k - IS 3346

• Base panel conforms to EN 13168 2001.

Variants by Density (does not apply to Size Zero)Anutone's unique VDH technology - Variable Density Hybrid- is available in Soak Cordura. This allows for space-savingA-mounting of panels but with AutoAir - an automaticairgap for an acoustic infill of Synth for additional soundabsorption. Panel size is restricted to 600x1200x25mmon H-Spline only. Applications include offices, hometheatres where more sound absorption than that providedby regular A-mounted Soak Strand Cordura is needed.

Now Size Zero makes VDH and AutoAir redundant incertain application. Strut CC10 with Synth 10x10 providesa slim backer to Soak Cordura 10 & 15mm thick panels.

Tech Performance - FabricFlammability Test Results as per AS1530 Part 3• Spread of Flame (Index 0-10) 0• Smoke Developed (Index 0-10)3As per AS/NZS 3837• Group Number 1 - Avg Specific Extinction Area 49.7m2/kgFlammability Test Results as per BS476• Part 5 - Ignitibility – ‘P’• Part 6 - Fire Propagation Index – 3.1• Part 7 - Class 1Y

3

Technical Variants

Fabric is a non-woven, needle-punched, chemically-free, thermally-bonded, multi-purpose acoustical fabric that is highlydurable with exceptional performance. It has been specially developed for the Soak series by Anutone in association withAutex of New Zealand. All fabric information in this brochure is based on data by Autex.

• 100% polyester

• Safe, non-toxic

• Recyclable, environmentally-friendly

• UV stable - resistant to fading

• Moisture-resistant - rot-resistant, stain resistant

• Durable - infinite product life

• Does not fray or zipper when cut

• 12 stock and 14 custom colours

• NRC 0.20 when directly adhered to hard walls

• Density 400 gsm

• Thickness 3mm

• Manufactured to ISO 9001 protocols

Visual Variants

Fabric Features

Calypso Simba Blaze

Avocado Skye Spearmint

Lime Jade Porcelain

Sanz Wasabi Myst

4

STOCKStandard fabric shades with short lead times.

CUSTOMCustom fabric shades with longer lead times.

Stately Silhouette Nautilus

Aubergine Blush Clay

Chilli Red Theatre

Silver

Koala

Lightsout Octane

Cinder Bark

Installation Drawings

5

Soak Cordura 10mm thick in dual tone - ‘C10’ mounting installed on StrutCC10 - Z-clip on panel and double clip on wall - with Synth 10x10 backing

Soak Cordura 10mm thick in dual tone - ‘A’ mounting installed directlyon wall (no airgap) - Z-clip on panel and double clip on wall

Soak Cordura 20mm thick - ‘C22’ mounting installed on Strut CC22 -H-Spline fitted in long kerfed edges - with Synth 10x25 backing

NOTE - Anutone has the capability, expertise and owninfrastructure to perform custom acoustics tests forgiven design as per ISO 354 at its Scans lab andprovide acoustic values of Soak Cordura specific toinstallations, a private sector first in South Asia.

Sound Absorption Coefficient as per ISO 354

Soak Cordura - 20mm thick kerfed edges joined with JEH Spline,mounted on Strut CC25

Site Considerations• Cartons of Soak Cordura must be stored on a flat, dry surface.

• They must not come in contact with water.

• Wall surfaces must be devoid of moisture prior to installation.

• The final act of panel installation must be performed only when all other works are completed and site has attainedoccupancy conditions in terms of room temperature and humidity.

• Trained and skilled technicians must install Soak Cordura. ‘Soft’ and ‘clean’ handling is a must. 10 & 15mm thickpanels are fragile and require very careful handling.

• For wall edges and corners where cut panels are required, the fabric can be peeled back and cut to size, the basepanel cut to size and fabric bonded again with rubber-based adhesives.

• Panels can be nylon brushed and/or vacuumed post-installation.

Anutone’s Selec programme makes it easy for architects, consultants, contractors and clients to apply Soak Cordurato architectural spaces. System selection of Soak Cordura is suitable for but not limited to the following spaces.

Acoustical Parameters

Applied Acoustics

Notes: Where sound absorption and noise isolation is required between rooms, then system selection must be madefrom the Soak Septum Cordura series with assistance from Anutone or better still, independent acoustical consultants.

Pax1 Acoustics2 NRC/STC3 Mtg4 Ods5 Panel Framework Infill

<25 Absorption Fair A 18 Soak Strand 10mm Z-Clip/Bar Nil

25-50 Absorption Medium A 30 Soak VDH 25mm H-Spline Synth 10x10

>50 Absorption Good C10 23 Soak Strand 15mm Strut CC10 SynthZ-Clip/Bar 10x10

<50 Absorption & Fair A 25 Soak Septum 20mm H-Spline NilIsolation Good

Conference Rooms / Training Rooms / Meeting Rooms

Spec Ambient Vibration Reverb Time Sound Level Freq Resp SpeechRC (N) Curve seconds dBA Hz RASTI

40 I 1.0 60 White >0.4

6

OFFICES

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

125 250 500 1000 2000 4000

10x10

10x25

Frequency (Hz)

Infill-Synth 125 250 500 1000 2000 4000 NRC

10x10 0.25 0.50 0.69 0.87 0.68 0.60 0.70

10x25 0.26 0.53 0.71 0.93 0.76 0.59 0.75

Notes: For variable sound absorption thatincludes LF-absorption and HF-reflection thesystem selection must include Soak StrandCordura and Soak Burl Cordura. Wheresound absorption and noise isolation isrequired between rooms, then systemselection must be made from the SoakSeptum Cordura series. This may requireassistance from Anutone or better still, theexpertise and experience of independentacoustical consultants.

1 Pax - Occupancy - number of persons andcorresponding volume of the space

2 Acoustics - Acoustical performancerequired - Sound Absorption or NoiseIsolation or both

3 NRC/STC - NRC is Noise ReductionCoefficient and related to SoundAbsorption; STC is Sound TransmissionClass and related to Noise Isolation

4 Mtg - Mounting - Panel mounting on basesurface as per ISO 354 and/or ASTM E795

5 Ods - Overall depth of system - from basesurface to panel surface, installed andfinished


<5 Absorption Fair A 25 Soak Strand 20mm H-Spline Nil

<5 Absorption Medium A 30 Soak VDH 25mm H-Spline Synth10x10

5-10 Absorption Good C25 47 Soak Strand 20mm Strut CC22 SynthH-Spline 10x25

NA Absorption LF Good C25 47 Soak Burl 20mm Strut CC22 SynthH-Spline 10x25

<50 Absorption & Fair A 25 Soak Septum 20mm H-Spline NilNA Isolation Good

STUDIO AND HOME THEATRE


<150 Absorption Fair A 23 Soak Strand 15mm Z-Clip/Bar Nil

150-500 Absorption Medium C25 47 Soak Strand 20mm Strut CC22 SynthH-Spline 10x25

NA Absorption LF Good C25 47 Soak Burl 20mm Strut CC22 SynthH-Spline 10x25

>500 Absorption Good C50 75 Soak Strand 20mm Strut CC50 SynthH-Spline 10x50

AUDITORIA AND CINEMA

Notes: For variable sound absorption that includes LF-absorption and HF-reflection the system selection must includeSoak Strand Cordura and Soak Burl Cordura with assistance from Anutone or better still, independent acoustical consultants.

7


Auditoria 30 H 1.2-1.5 95 50-20k >0.6

Cinema 30 H 0.7 105 40-20k >0.6


Studio 20 F 0.4 95 40-20k >0.6

Home Theatre 25 G 0.7 90 50-20k >0.6

STEP 1 & STEP 2Mark location of each panel on wall for A-mounting (or on Strut CC10/22/50 for C or D-type mounting), to determine panel usage,position and inside/outside corner details.Install Sonator wooden skirting at base ofwall for panel support. Make sure it is level.Height of skirting depends on architecturalrequirements, usually 150 mm.

STEP 3 & STEP 4Position first panel, using level to assureplumb. Insert first H-spline section intogroove on panel long edge and against wall.Start at top of panel. Spline should be suitablyattached to the wall so that it is firmly inplace. Add splines down to rest of thepanel till the Sonator wooden skirting, makingsure plumb is maintained.

STEP 5Position next panel onwall and slide itagainst first H-splineuntil they fully engagein the groove. Fix H-spline to oppositeedge groove and to

wall as done with first panel. Continueprocedure along wall length, checking plumbof each panel.NOTE : If a cut Soak Cordura panel is neededto fill inside corner, do not fasten the last rowof H-splines to wall.

STEP 6Measure spacefrom last panel tocorner at top,middle andbottom of area.

Transfer these measurements to the faceof the panel. Place panel, fabric side up, onsmooth and clean surface and using handor power saw, cut through fabric and panelso that cut edge is the edge that will fit in thecorner.

STEP 7Apply adhesive to back of last full panel alongopen H-spline that will be used in that edge,(See B), and to back of cut panel, (See C).Insert the last attached H-spline. Insert H-spline with adhesive into other groove oflast full panel. Insert groove of cut panel intothe H-spline and insert cut edge into corner.Then apply pressure at joint between panel(See D), until contact is made with the wall.Hold until adhesive sets. Secure cut cornerpanel to wall with four finishing nails alongoutside edge of panel at corner. Space themevenly and drive at 450 angle. A new, fullpanel should be used as the first panel afterthe corner (See E). Butt it against front ofcut corner panel after putting adhesive alongthe length of the panel’s thickedge. Continue down this wall (Steps #1through #5).

STEP 8Measure spacefrom last full panelto corner at top,middle and bottom.

Add 50mm, to these measurements.Transcribe these measurements to face ofpanel to be cut. Place panel, fabric side up,on smooth and clean surface, using hand orpower saw, cut through the fabric and panelalong the marked line.

STEP 9Gently peel fabricback 75mm from cutedges of both panelpieces. Draw a line

on the Soak Cordura panels of both pieces50mm back from the cut edge, and parallel tothe cut edge along the length of the panel.

STEP 10Making sure thefabric is foldedback out of the way,cut off this 50mmwide strip of the

base panel on both pieces. Remove any loosefibres that may remain.

STEP 11On one piece, apply hot melt glue to the panelalong the 25mm wide exposed top where

the material waspeeled back, alongthe cut edge, andalong a 25mm widestrip on the back

next to the cut edge. Wrap fabric back overface, around edge, and over back so itadheres, stretch tight, eliminating any foldsor creases. Repeat procedure with otherpanel piece.

STEP 12On panel cut to fitcorner width,apply adhesive toSoak Cordura

panel along the length of the panel, just beyondfabric along the cut edge. Place panel on walland slip it into the last installed H-spline. Hold untiladhesive sets.

STEP 13Apply adhesive insame manner toother panel piece.Position it on wall

around corner so it completely overlaps endof other corner panel. Slip H-spline into thegroove in the opposite edge and continuedownward in the same manner as previously.

H-Spline System

Installation Guidelines - 20mm on H-Spline

8

Soak Cordura range of products are extremely durable and require little attention to maintain their good looks. Lightvacuuming on a regular basis will prevent dust build up and most marks can be cleaned with a mild detergent solutionfollowed by rinsing and blotting. Stains should be dealt with according to the chart below.

• Before carrying out a proposed cleaning method, apply to a concealed section to ensure it will not affect the adhesiveor wall covering

• Avoid severe abrasion• Vacuum to restore pile, but do not use a stiff brush.

Note: Anutone does not recommend solvent based cleaners on Soak Cordura

Anutone offers the above recommendations in good faith. However, Anutone cannot be responsible for unsatisfactoryresults arising from the proposed treatments.

Anutone recommends that you contact professional cleaning experts should you require further assistance with thecleaning and maintenance of Soak Cordura.

Maintenance

A Mop up excess as soon as possible with a sponge or cloth.

B Remove surplus with a knife edge or appropriate instrument.

C Sponge with a solutions of carpet shampoo working from well outside the stain in a circular motion towards thecentre (this avoids spreading the stain). Sponge afterwards with clean warm water and mop up excess moisturewith a clean dry cloth or sponge. Allow to dry then brush gently with a soft brush. If any stain remains, sponge witha solution of one part household bleach to six parts clear water. Thoroughly rinse after treatment.

D Lightly sponge with household dry cleaning fluid and blot. Apply sparingly, as the substance may have an adverseeffect on the adhesive.

E Sponge with methylated spirits and blot dry.

G Apply nail polish remover. The nail polish remover should not include lanolin or be of a greasy nature.

H Sponge with turpentine (or substitute).

I Freeze with ice cubes and scrape away while cold.

J Clean with regular extractive carpet cleaner (if possible).

K Use circular cutter and remove damaged portion. Re-glue new piece into place.

Stain Treatment Guide Stain Treatment Guide

Blood A C Lipstick B E C D

Burn/Scorch Mark K Mildew C

Chewing Gum I B D C Milk A E

Chocolate B D C Mud B C

Cooking Oils B D C Nail Polish A G

Crayon/Colour Markers B D C Oil B D C

Drinks (cola, tea, juices, beer etc) A C Paint (water based) A C

Dust/Dirt Vacuum, then J or C Paint (oil based) A H D C

Excrement B C Sauces B C D

Grass C Shoe Polish B C D

Grease B D C Urine A C

Ink (ballpoint) D E Vomit A C D

Ink (fountain) A C Wine A Add Salt C

9

Soak Cordura 10mm on wall - A mounting

Scope – Design, Supply, Build of Soak Cordura as designed,manufactured and installed, per approved drawings andspecifications, by Anutone Acoustics Limited, an ISO 9001 2008and 14001 2004 company.

Support – Supplied Z-Clips are installed on the panel reverse oncement spots provided. Supplied Double Wall Clips are installed onthe wall as marked. For ends the double wall clips are easily cut atsite to make them single.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______m2; Colour ______ & _______ ; Size 600x1200mm; Thickness 10 mm.Joints and finish – Pencil radius edges, butt-joined.

Soak Cordura VDH 25mm on wall - A mounting

Scope – Design, Supply, Build of Soak Cordura VDH as designed,manufactured and installed, per approved drawings andspecifications, by Anutone Acoustics Limited, an ISO 9001 2008and 14001 2004 company.

Framework – H-Spline is installed parallel to the long edges of theSoak Cordura VDH with suitable mechanical fasteners that areanchored firmly to the base surface.

Infill - Synth AW 10x10 is friction-fitted inside the Soak Cordura VDH.

Panels – Soak Strand Cordura VDH _______ m2 & Soak StrandBurl VDH _______ m2; Colour ______ & _______ ; Size600x1200mm; Thickness 25 mm. Joints and finish – Pencil radiusedges, butt-joined.

Soak Cordura 10mm on CC10 - D10 mounting


Framework – Strut CC10 fixed at 600mm centres. CC10 must beinstalled perpendicular in relation to the long edges of the panels.Z-Clips are installed on the panel rear and Double Wall Clips areinstalled on the Strut CC10.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______m2; Colour ______ & _______; Size 600x1200mm; Thickness 10 mmJoints and finish – Pencil radius edges, butt-joined.

Soak Cordura 10mm on CC10 with Synth - C10 mounting


Framework – Strut CC10 fixed at 600mm centres. CC10 must beinstalled perpendicular in relation to the long edges of the panels.Z-Clips are installed on the panel rear and Double Wall Clips areinstalled on the Strut CC10.

Infill - Synth AW 10x10 is friction-fitted between the Strut CC10 andlightly adhered with Stick S7.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______m2; Colour ______ & _______; Size 600x1200mm; Thickness 10 mm.Joints and finish – Pencil radius edges, butt-joined.

Custom MethodologyThe installation of Soak Cordura can be custom-designed to specific needs by Anutone to suit specific or specialproject requirements. The methodology includes the entire value-chain - site evaluation, criteria definition, noisespectra capture, design optimisation, system specs, systems engineering & integration, project management,acoustic testing & site validation.

System Specifications



Framework – Strut CC22 fixed at 600mm centres. CC22 must beinstalled perpendicular in relation to the long edges of the panels.The H-Spline is installed perpendicular to the Strut CC22 and parallelto the long edges of the panel.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______m2; Colour ______ & _______; Size 600x2400mm; Thickness 20 mmJoints and finish – Pencil radius edges, butt-joined.

Soak Cordura 20mm on CC22 with Synth - C22 mounting


Framework – Strut CC22 fixed at 600mm centres. CC22 must beinstalled perpendicular in relation to the long edges of the panels.The H-Spline is installed perpendicular to the Strut CC22 and parallelto the long edges.


Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______m2; Colour ______ & _______; Size 600x2400mm; Thickness 20 mm.Joints and finish – Pencil radius edges, butt-joined.


Scope – Design, Supply, Build of Soak NSS as designed,manufactured and installed, per approved drawings andspecifications, by Anutone Acoustics Limited, an ISO 9001 2008and 14001 2004 company.



Soak Cordura on CC50 with Synth - C50 mounting

Scope – Design, Supply, Build of Soak as designed, manufacturedand installed, per approved drawings and specifications, by AnutoneAcoustics Limited, an ISO 9001 2008 and 14001 2004 company.




10

NEW

NEW

NEW

Sl # Description Units Soak Cordura

Walls - H-Spline Walls - Z-Clip

Size / Edge mm 600x2400 / C25 Mounting 600x1200

25 mm 10 mm 15mm

1 Z - clips on walls nos. 834 834

2 Z - clips on Panel nos. 834 834

3 Strut CC22 lm 198

4 Spline lm 288

5 Stick S7 Ltr 35

6 Synth AW 10x25mm thick m2 100

7 Panels m2 100 100 100

8 Labour hrs 3 2 2

Estimated Installed Cost / m2 Rs 4,450.00 3,160.00 3,470.00

lm - Linear meter, m2 - Square meter, Ltr - Litre, LS - LumpSum, hrs - Hours

Sl# Description Soak Cordura

1 Thickness (mm) 10 / 15 / 20 / 25 / 30 / 40 / 50

2 Size (mm) Width 600 / Length 1200 for 10, 15mm and 1200/2400 for >20mm

3 Core Strand / Synth

4 Nominal Density (Kg/m3) 400 to 500

5 Weight (Kg/m2) upto 25

6 Edge Square for 10, 15mm; Square with long edges kerfed for >20mm

7 NRC / STC Upto 0.9

8 Fire Class I

9 Moisture Resistance (%) RH 90

10 Light Reflectance (%) Colour Dependant

11 Warranty 10 years

12 Installation 10, 15mm on Z-Clip/Bar; >20mm on H-Spline; Strut CC10, CC22, CC 50

13 Colour 12 stock; 14 custom

14 Maintenance Nylon-bristles brush; Vacuum

Technical Specifications

Bill of Quantities (BoQ) - 100m2

11

* The above indicated values are very approximate and dependent on several variables. They are for guidance only, and subject to change without prior notice.

References

Office

Intel BengaluruGolden Wood Packer BhubaneshwarAEPC HaryanaGodrej & Boyce MumbaiNHPC New DelhiTirupur Chamber of Commerce Tirupur

Auditorium

Gaiety Theatre Simla

Cinema

Shree Radha Movie Park Chennai

Places of Worship

Swami Shri Prempuri Ashram Mumbai

Studio

INX Studio NoidaNine X Studio Mumbai

Home Theatre

Mr. K.J. Venkatesh BengaluruMr. S.P. Kumar BengaluruMr. R.R. Ranganathan Coimbatore

For the latest update on our projects list please visit www.anutone.com/projects or contact Anutone.

Do

cum

en

t #

90

90

10

-50

0

231, 7th Cross, Indiranagar 1st Stage,Bengaluru 560 038, IndiaPhone +9180 2520 3114Fax +9180 2520 [email protected]

ANUTONE INTERIORS(a division of Anutone Acoustics Limited)

Anutone® is a registered trademark of Anutone Acoustics Limited. Specs are subject to change due to continuous improvement programmes at Anutone®. Contents under copyright registration. No part of thisbrochure may be reproduced, stored in a retrieval system, scanned or transmitted in any form or by any means electronic, photocopying, recording or otherwise, without the prior written permission of Anutone®.

www.anutone.com

• Bahrain • Budapest • Chennai • Dammam • Doha• Dubai • Jeddah • Kolkata • Kuwait • Manila• Mumbai • Muscat • Nairobi • New Delhi • Riyadh

Anutone is member of

ISO 9001:2008 CERTIFIED ISO 14001:2004 CERTIFIED

Size Zero is the current fad. Everybody wants it slim,

superslim! After Size Zero laptops, smartphones,

televisions and ramp models, comes the ultra-slim, ultra-chic Soak series of fabric-wrapped wall panels.

Soak Cordura earlier had a limitation of minimum thickness,20mm. This was due to kerfed long edges to receive H-

Spline. This also resulted in a site problem of panels being

able to be dismantled from one corner only.

Now to meet the demand from designers for space-saving

slimmer panels, Anutone has innovated to result in 10mmthick panels that can be hung on walls and more importantly

dismantled from any point. Also all edges are fully finished

so panels can be installed discretely as floating islands!

More on Size Zero in Soak Cordura

Feature Benefits

Ultra-slim, ultra-chic – all edges finished Architect

Discrete install - wall island floats Architect

Space saving – 10mm thickness only Builder

Economical – slim means less costs Customer

Frequency response – additional bass Acoustician

Matching accessories – slim channel & infill Contractor

Snag-free - single source compatibility Project Manager

Accessibility – any point dismountable Facility Manager

Highlights

NEW

Documents

Soak Cordura Brochure