3
Sikafloor ® -Pronto Systems Fast Curing Flooring Solutions Selection Guide

Sikafloor -Pronto Systems Fast Curing Flooring …®-Pronto®– Colour Range Sikafloor®-Pronto Pigments are available in standard colour range: ~ RAL 7032, ~ RAL 7035, ~ RAL 7038,

Embed Size (px)

Citation preview

Page 1: Sikafloor -Pronto Systems Fast Curing Flooring …®-Pronto®– Colour Range Sikafloor®-Pronto Pigments are available in standard colour range: ~ RAL 7032, ~ RAL 7035, ~ RAL 7038,

Sikafloor®-Pronto SystemsFast Curing Flooring SolutionsSelection Guide

Page 2: Sikafloor -Pronto Systems Fast Curing Flooring …®-Pronto®– Colour Range Sikafloor®-Pronto Pigments are available in standard colour range: ~ RAL 7032, ~ RAL 7035, ~ RAL 7038,

Project Related Performance Requirements of Flooring SystemsDetailing SolutionsRepair and Coving Mortar:n Sikadur®-12 Pronto repair mortar

and Sika®-Pronto Coving Mortar.Rapid curing properties are necessary to ensure minimum disruption to production.

Mechanical resistance – which must be defined by type (load, tyres, contact area etc.), and frequency of traffic and exposure.

Chemical resistance (please refer to the Sikafloor® Chemical Resistance Chart).

Floor areas may require different degrees of slip resistance, dependent on their environment, i.e. ‘wet’ or ‘dry’ processing areas. (see Sikafloor test certificates).

Impact resistance is as variable as each operation. Allowance should be made for the highest possible point loads.

To provide an impermeable seal to protect both the base concrete from attack by aggressive liquids and the underlying ground water from the leakage of pollutants.

Increasingly specific requirements for the prevention and easy removal of contamination, particularly in the nuclear, pharmaceutical, cosmetic, food, beverage, chemical and electronics industries.

Colour stability can be an important requirement, particularly where high UV Light exposure is anticipated. Use the UV resistant and light fast Sikafloor® Systems.

To stay in shape, look good and give years of service, it is necessary to provide fully detailed cleaning guidelines and maintenance advice. This is all available in the Sikafloor® Cleaning Regime, which is available to download from: www.sika.com.

For durable flooring static and/or dynamic crack-bridging abilities are often required, to protect the substrate in the event of movement or vibration from traffic etc.. i.e. on mezzanines or in car parks. Alternatively sufficient movement joints must be incorporated at the design stage.

Broadcast Fast Curing Crack-Bridging ScreedSikafloor®-15 /-18 Pronto

Total system thickness: approx. 2 – 4 mm

Primer: Sikafloor®-10 /-13 ProntoBase coat: Sikafloor®-15 Pronto Broadcast: Coloured or natural quartz sandSeal coat: Sikafloor®-18 Pronto (optional: Sikafloor®-Pronto Pigments)

A three part, fast curing system based on reactive acrylic resins.

Broadcast Fast Curing Screed

Sikafloor®-14 /-16 or -18 Pronto

Total system thickness: approx. 2 – 4 mm

Primer: Sikafloor®-10 /-13 ProntoBase coat: Sikafloor®-14 Pronto Broadcast: Coloured or natural quartz sandSeal coat: Sikafloor®-16 /-18 Pronto (optional: Sikafloor®-Pronto Pigments)

A three part, fast curing system based on reactive acrylic resins.

Broadcast Fast Curing Elstomeric ScreedSikafloor®-15 /-17 Pronto

Total system thickness: approx. 2 – 4 mm

Primer: Sikafloor®-10 /-13 ProntoBase coat: Sikafloor®-15 Pronto Broadcast: Coloured or natural quartz sandSeal coat: Sikafloor®-17 Pronto (optional: Sikafloor®-Pronto Pigments)

A three part, fast curing system based on reactive acrylic resins.

Smooth Fast Curing Decorative ScreedSikafloor®-14 /-16 Pronto

Total system thickness: approx. 2 – 4 mm

Primer: Sikafloor®-10/-13 ProntoBase coat: Sikafloor®-14 Pronto Broadcast: Coloured flakesSeal coat: Sikafloor®-16

A three part, fast curing system based on reactive acrylic resin.

Fast Curing SolutionsSikafloor®-Pronto systems are suitable for:n All manufacturing facilities, where

minimum downtime of the production process is required, regardless of a dry or wet production process.

n All facilities in the food or beverage industry with a demand for fast curing and temperature resistant floors, from a steam cleanable surface to a cold storage room.

n For crack-bridging, trafficable, slip resistant wearing surfaces for multi-storey and underground car-parks.

n Decorative waterproofing surfaces for balconies or walkways.

Performance Related Advantagesn Sikafloor®-Pronto system can

be applied in a wide range of climatic conditions, especially suitable for lower temperatures.

n Variety of different surface finishes possible ranging from broadcast to self-smoothing in order to offer easy to clean systems or surfaces with a high degree of slip resistance.

n Systems can be individually designed in order to fulfil many different requirements, such as crack-bridging properties, impact or temperature resistance.

Application Related Advantagesn Installation of complete systems during

one day in order to reduce application costs.

n Flexibility in system build-up to adapt to the needs during installation.

n Special products for detailing and connections, such as drainage, gullies etc.

Detailing and Connections to Drainage:n Example: Connection to drainage channels

using Sikafloor®-10 Pronto as a primer for the concrete and steel surfaces, followed by elastomeric Sikafloor®-15 Pronto to fill, level and seal the adjacent areas.

Primer for Difficult Substrates:n Sikafloor®-10 Pronto is a special

adhesion promoting primer to be used on difficult substrates, such as dense concrete, tiles, asphalt or metal.

Reinforced Layer for Daywork Joints or Details:n Reinforced layer using Sikafloor®-15

Pronto as the base coat and encapsu-lation layer for Sikalastic®-120 Fleece.

Solutions for Special Substrates

Page 3: Sikafloor -Pronto Systems Fast Curing Flooring …®-Pronto®– Colour Range Sikafloor®-Pronto Pigments are available in standard colour range: ~ RAL 7032, ~ RAL 7035, ~ RAL 7038,

Sikafloor®-Pronto®– Colour RangeSikafloor®-Pronto Pigments are available in standard colour range: ~ RAL 7032, ~ RAL 7035, ~ RAL 7038, ~ RAL 7040, ~ RAL 7042

Colour variations may occur due to backfilling with quartz sand. Under direct sun light there may be some discolouration and colour variations; this has no influence on the function and performance of the coating.

Also Available from Sika

Sika® Technology and Concepts for Flooring and Coating

Our most current General Sales Conditions shall apply. Please consult the Product Data Sheet prior to any use and processing.

Sika Services AGBusiness Unit ContractorsSpeckstrasse 22CH-8330 PfäffikonSwitzerlandPhone +41 58 436 23 64Fax +41 58 436 23 77www.sika.com

Sikafloor® and Sikagard®

Cleanroom suitable Solutions

Flooring and Wall Coating Solutions for Cleanroom Environments

Selection Guide

Sika®-ComfortFloor®

Sikafloor Solutions for Commercial and Public Building Areas

Selection Guide

Sikafloor®-Economy LineModular Epoxy Flooring Solutions for all Industries and RequirementsSelection Guide

Our most current General Sales Conditions shall apply. Please consult the Product Data Sheet prior to any use and processing.

BU C

ontra

ctor

s / 1

1.07

/ ar

Also available from Sika

Sikafloor®-Economy Line

Sikafloor® Modular Epoxy Flooring Line – Colour RangeSikafloor®-263 SL and -264 are available in an extended colour range, such as RAL 1001, RAL 6021, RAL 7030, RAL 7032, RAL 7035, RAL 7037, RAL 7038, RAL 7040, RAL 7042, RAL 9002

Colour variations may occour due to backfilling with quartz sand. Under direct sun light there may be some discolouration and colour variations; this has no influence on the function and performance of the coating.

Product PackagingSikafloor®-1612-part, solvent-free, epoxy primer and binder.

30 kg units / 200 kg drums

Sikafloor®-263 SL2-part, solvent-free, self-smoothing epoxy screed.

20 kg units / 200 kg drums

Sikafloor®-2642-part, solvent-free, epoxy roller and seal coat.

30 kg units / 200 kg drums

Sika Services AGBusiness Unit ContractorsSpeckstrasse 22 CH-8330 PfäffikonSwitzerlandPhone +41 44 403 13 64 Fax +41 44 403 13 77www.sika.com

Sikafloor®-Pronto SystemsFast Curing Flooring SolutionsProduct PackagingSikafloor®-10 Pronto4-part, fast curing primer for critical substratesPart A: Sikafloor®-10 Pronto 21.2 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Part C: Sikafloor®-Pronto AP 1: 8.0 kgPart D: Sikafloor®-Pronto AP 2: 0.1 kgSikafloor®-13 Pronto2-part, fast curing primerPart A: Sikafloor®-13 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Sikafloor®-14 Pronto3-part, fast curing self-smoothing screed and levelling mortarPart A: Sikafloor®-14 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Part C: Sikafloor®-Pronto Filler: 25 kgSikafloor®-15 Pronto3-part, flexible fast curing self-smoothing screed and levelling mortarPart A: Sikafloor®-15 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Part C: Sikafloor®-Pronto Filler: 25 kgSikafloor®-16 Pronto2-part, fast curing seal coatPart A: Sikafloor®-16 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)

Product PackagingSikafloor®-17 Pronto2-part, flexible fast curing seal coat for wet areas or cold storage roomsPart A: Sikafloor®-17 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Sikafloor®-18 Pronto2-part, flexible fast curing seal coat for internal and external areasPart A: Sikafloor®-18 Pronto: 25 kg, 200 kgPart B: Sika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Sikafloor®-Pronto FillerSikafloor®-Pronto Filler: 25 kgSikafloor®-Pronto HardenerSika®-Pronto Hardener: 1.0 kg (in 0.1 kg bags)Sikafloor®-Pronto PigmentSika®-Pronto Pigment: 5 kg (10 x 0.5 kg bags)Sikadur®-12 Pronto2-part, fast curing repair mortar Part A: 2.75 kg containersPart B: 22.25 kg bagsPart A+B: 25.00 kg ready to mix units

© S

ika

Serv

ices

AG

/ BU

Cont

ract

ors

/ Sik

afloo

r Pro

nto

Syst

ems

/ 02.

2009

/ HB

Sika®-Pronto Coving Mortar3-part, fast curing coving mortar Part A: Sika®-Pronto Coving Paste 25 kgPart B: Sika®-Pronto Hardener Part C: Quartz or coloured quartz

sand 0.7 – 1.2 mm

22.25 kg bags 25 kg