Shure PGXD Wireless User Guide - All Pro Sound

Shure PGXD Wireless

PGXD Wireless System

PGXD sans fil de Shure

Shure PGXD Sem Fio

©2010 Shure Incorporated 27B14513 (Rev. 2) Printed in U.S.A.

D

D

D

D

D

D

D

D

1

PGX Digital Wireless Systems

Offering uniquely tailored wireless solutions for vocalists, guitarists, and presenters, PGX-Digital combines the trusted legacy of Shure wired microphones with state-of-the-art, 24-bit digital wireless technology to deliver strong, clean RF performance. The result is wireless audio that sounds like wired, rock-steady RF signal even at extended distances, and plug-and-play setup and operation.

• Professional quality 24-bit digital audio• Digital RF technology for rock-solid

performance• Wide variety of rugged and dependable Shure

microphones• One-touch setup and operation• Up to 10 hours of battery life (9 hours,

PGXD2) • Up to 200 foot range (line-of-sight)• 900 MHz operation—free from white spaces or

DTV interference

System Components

All systems include • PGXD4 receiver• 2 AA alkaline batteries• Power supply• User guide

Vocalist systems include • PGXD2 handheld transmitter• Microphone head (choice of PG58, SM58®,

SM86, Beta 58A® or Beta 87A*)• Microphone clip* Available only in select markets

Lavalier, Headworn, and Instrument systems include • PGXD1 bodypack transmitter• Microphone (choice of WL93, WL185, PG30 or

Beta 98H/C)

Receiver Controls and Connectors

① audio LEDIndicates strength of incoming audio signal: green for normal, amber for strong and red for clipping.

② LED ScreenDisplays group and channel setting. See “Single System Setup” for details.

③ channel buttonChanges group and channel setting. See “Single System Setup” for details.

④ ready LEDIndicates system ready and receiving an RF signal from the transmitter.

Also indicates battery level of the transmitter:

• Green = transmitter battery level normal

• Red = low battery (typically less than 60 minutes with alkaline batteries)

Note: with NiMH rechargeable batter-ies, when the indicator turns red there will be little to no remaining life.

⑤ Infrared (IR) portSends IR signal to transmitter for sync.

⑥ sync buttonPress to synchronize transmitter with receiver group and channel settings.

PGXD

PGXD4

Guitar systems include• PGXD1 bodypack transmitter• 1/4” to mini 4-pin guitar cable

(WA302)

2

⑦ AC adapter jack

⑧ Adapter cord tie-off

⑨ XLR microphone output jack

⑩ 6.35 mm (1/4”) instrument level output jack

Transmitter Controls and Connectors

① Indicator LEDDisplays battery level, mute, and IR transmission status (see table).

② Power / Mute SwitchPress to mute or unmute. Press and hold to power on or off.

③ Infrared (IR) portReceives infrared beam to synchronize frequencies. When using multiple systems, only one transmitter IR port should be exposed at a time.

④ 4-Pin Microphone Input Jack

⑤ Audio Gain Adjustment

PGXD2

PGXD1

PGXD

BIAS

AUDIO

0dB -10dB

PGXD

LED Indicator StatusGreen Ready

Flashing green Controls locked

Amber Mute on

Solid red Battery power low

Flashing red Batteries dead (change batteries to power on transmitter)

Rapidly flashing red IR transmission in process

Flashing amber and red

Battery power low and mute on

Transmitter Indicator LED

INSTRUMENTMIC

3

BIAS

AUDIO

0dB -10dB

AUDIO

0dB -10dB

Wearing the Bodypack Transmitter

Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.

For best results, slide the transmitter until the belt is pressed against the base of the clip.

Adjusting Gain

Handheld TransmitterAccess the gain switch by unscrewing the head of the microphone.

Use the tip of a pen or a small screwdriver to move the switch.

• 0dB: For quiet to normal vocal performance.• –10dB: Use only if audio is distorted due to high

vocal levels.

PGXD

Batteries

• A fresh set of alkaline batteries lasts up to 10 hours (9 hours, PGXD2).

• The transmitter LED and the receiver ready LED glow red to indicate low battery (typically less than 60 minutes remaining).

• NiMH rechargeable batteries may be used. However, the low battery indicator functions differently. When it turns red, there may be little to no remaining life.

• When the LED flashes red, the batteries must be replaced to power on the transmitter.

PGXD

Bodypack TransmitterThe bodypack has 26 dB of audio gain adjustment.

• Increase gain (clockwise +) for microphones• Decrease gain (counterclockwise –) for guitars

or high-output instruments

For best audio quality, set transmitter gain so the audio LED on the receiver flickers green and amber during the performance. Decrease gain if the signal clips (LED turns red).

Note: The amber LED may appear to be red when viewed at an angle. For best results, monitor the LED from directly in front.

4

channel

Single System Setup

ScanUse the scan feature on the receiver to find a clear channel.

LED screen displays current channel

press channel button to scan for a

clear channel

system scans for the channel with the least interference

SynchronizeSynchronize the transmitter to the receiver by aligning the infrared (IR) ports and pressing the sync button. Make sure the IR ports are closely aligned.

After a successful sync, the transmitter LED momentarily flashes red and the receiver ready light illuminates.

Multiple System Setup

NOTE: This wireless system may be affected by RF inter-ference when used in proximity to other wireless devices such as cordless phones, baby monitors, and two-way ra-dios. For best results, use the scan and sync feature before each use or if you experience problems.

Use the following steps to ensure the best performance when installing multiple wire-less systems at the same location.

1. Turn all receivers on and all transmitters off.

Note: Turn on any other digital equipment that could cause interference during the performance so it will be detected during the frequency scans in the following steps.

2. Make sure the group number is the same for all receivers (see Manual Group Selection).

3. Perform a scan using the first receiver.

4. Turn on the first transmitter and sync it to the receiver.

5. Repeat for each system.

• Important: After syncing each transmitter, leave it on so that scans from the other receivers will not select that channel.

• Be sure only one transmitter IR port is exposed when synchronizing each system. Compatible FrequenciesWhen operating multiple systems simultaneously, choose one group from the following table and set all systems to different channels within that group.

Number of Systems

Group (by band)X8 X8A

(Austrailia)X8B (Brazil)

2 3 to 9 3 to 9 3 to 9

3 3 to 9 3 to 9 3 to 9

4 3 to 9 -- 3 to 9

5 7 to 9 -- --

5

ReceiverTo lock the channel: Hold the channel button until the numbers flash (~10 seconds)

To unlock the channel: Hold the channel button until the numbers flash (~5 seconds)

Manual Channel and Group Selection (receiver only)

Using the receiver to scan for a channel is the best way to find the best frequency for your system. However, for multiple system setup, you may need to manually set the group number.

1. Press and hold the channel button.

2. Hold the button until the channel or group display begins flashing.

3. Release and press the button again to advance the setting.

At the desired channel or group number, wait for the flashing to stop. This activates the new setting.

4. Transfer the new frequency setting to the transmitter using the automatic sync function.

select 6 sselect 3 s

channelchannel

channelchannel

channel

channelchannel

channel

channel

Locking and Unlocking Controls

Locking the system controls prevents accidental muting or channel adjustment during performances.

TransmitterTo lock the controls: With the transmitter off, hold the power button down until the green LED flashes (~5 seconds)

To unlock the controls: With the transmitter on, hold the power button down until the green LED flashes (~5 seconds)

channel

group display channel display

6

Troubleshooting

Issue Indicator Status SolutionNo sound or faint sound

Receiver ready LED on Verify all sound system connections

Receiver ready LED off • Turn on transmitter• Make sure the batteries are installed correctly• Perform automatic transmitter setup• Insert fresh batteries

Receiver LED screen off Make sure AC adapter is securely plugged into electrical outlet

Transmitter indicator LED flashing red

Replace transmitter batteries.

LED screen shows dash and value

Error code displayed. Contact your Shure reseller for assistance.

Transmitter LED flashes red for 7 seconds after attempting to sync

Transmitter and receiver incompatible. Contact your Shure reseller for assistance.

Noise bursts or audio dropouts

N/A • Change receiver and transmitter to a different channel

• Remove nearby sources of RF interference such as cordless or cell phones, computers, wireless routers, media players, digital signal processors, and security systems.

• Replace transmitter batteries• If using multiple systems, change the frequency of

one of the active systems

Distortion Audio LED on receiver indicates clipping (red)

Reduce transmitter gain

Distortion increases gradually over time

Transmitter power light glowing or flashing red

Replace transmitter batteries

Sound level different from cabled guitar or microphone or when using different guitars

N/A Adjust transmitter gain as necessary

Cannot turn transmitter on

Transmitter LED slowly flashing red

Replace transmitter batteries

Transmitter LED rapidly flashing red

Contact your Shure reseller for assistance.

50 ohms

1/4” Output

50 ohms

XLR Output

50 ohms

50 ohms

7

Working Range (Line of Sight)60 m (200 ft) Note: Actual range depends on RF signal absorption, reflection and interference.

RF Carrier RangeX8: 902–928 MHzX8A: 915–928 MHzX8B: 902–907.5 MHz, 915–928 MHzNote: varies by region

Audio Frequency Response20–20000 HzNote: Dependent on microphone type

Total Harmonic Distortion (Ref. 1 kHz, 6 dB below input clip)<0.02%, A-weighted, typical

Dynamic Range>108 dB, A-weighted

Operating Temperature Range-18°C (0°F)– +50°C (122°F)Note: Battery characteristics may limit this range.

Transmitter Audio PolarityPositive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low-impedance output) and the tip of the high impedance 1/4-inch output.

PGXD1 Bodypack TransmitterAudio Input Level+10 dBV maximum, at minimum gain setting-16 dBV maximum, at maximum gain setting

Gain Adjustment Range26 dB

Input Impedance1 MΩ

RF Output Power10 mWvaries by region

Pin AssignmentsTA4M: 1: ground (cable shield)2: + 5 V Bias3: audio4: Tied through active load to ground (On instrument adapter cable, pin 4 floats)

Dimensions108 mm x 64 mm x 19 mm (H x W x D)

Weight128 g (4.5 oz.)(without batteries)

HousingMolded polycarbonate case

Power Requirements2 “AA” size alkaline or rechargeable batteries

Battery Lifeup to 10 hours

PGXD2 Handheld TransmitterAudio Input Level+5 dBV maximum at -10 dB gain position–5 dBV maximum at 0 dB gain position

Gain Adjustment Range10 dB

RF Output Power10 mWvaries by region

Dimensions254 mm X 51 mm dia. (10 X 2 in.)

Weight349 g (12.3 oz.) (without batteries)

HousingMolded PC/ABS handle and battery cup

Power Requirements2 “AA” size alkaline or rechargeable batteries

Battery Lifeup to 9 hours

PGXD4 Wireless ReceiverDimensions40 mm X 181 mm X 104 mm (H x W x D)

Weight289 g (10.2 oz.)

HousingABS

Sensitivity-102 dBm @ 10-5 BER

Power Requirements12–18 V DC @ 150 mA, supplied by external power supply (tip positive)

Audio LEDRed: 2 dB below clipAmber: 12 dB below clipGreen: 50 dB below clip

Audio OutputConfigurationImpedance balanced

Audio Output Level (1 kHz tone)XLR connector: –2.5 dBV (into 3 kΩ load)6.35 mm (1/4”) connector: +10 dBV (into 10 kΩ load)

ImpedanceXLR: 50 Ω6.35 mm (1/4”): 50 Ω

Pin AssignmentsXLR: 1=ground, 2=hot, 3=cold6.35 mm (1/4”) TRS: Tip=audio, Ring=no au-dio, Sleeve=ground

SPECIFICATIONS

8

CERTIFICATION

PGXD1, PGXD2, PGXD4This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Certified by IC in Canada under RSS-210 and RSS-102. (IC: 616A-PGXD1, 616A-PGXD2, 616A-PGXD4).

PGXD1, PGXD2Certified under FCC Part 15. (FCC ID: DD4PGXD1, DD4PGXD2).

LICENSING INFORMATIONLicensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

INFORMATION TO USERThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer. Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

PGXD4Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.

Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

50 ohms

1/4” Output

50 ohms

XLR Output

50 ohms

50 ohms

www.shure.com ©2010 Shure Incorporated

Europe, Middle East, Africa:Shure Europe GmbHWannenäckestr. 28,74078 Heilbronn, Germany

Phone: 49-7131-72140Fax: 49-7131-721414Email: [email protected]

Asia, Pacific:Shure Asia Limited22/F, 625 King’s RoadNorth Point, Island EastHong Kong


United States, Canada, Latin America, Caribbean:Shure Incorporated5800 West Touhy AvenueNiles, IL 60714-4608 USA

Phone: 847-600-2000Fax: 847-600-1212 (USA)Fax: 847-600-6446Email: [email protected]















Documents

Shure PGXD Wireless User Guide - All Pro Sound