S E N S O R S & W I R E L E S S

i n f o @ d p s t a r . c o m.my w w w. d p s t a r . c o m . m y

ecoSTAR BasicIndustrial wireless radio sensors

ecoSTAR Basic is the new ecoSTAR’s industrial radio wireless system using state-of-the-artwireless technology (Frequency Hopping Spread Spectrum) to provide industrialmonitoring and control solutions with the highest reliability and efficiency. The system operates inStar Topology providing full monitoring and solution from Wireless Sensor Transceivers, through thewireless network coordinator (Control Panel) to the data acquisition software in Control Room.

• Real Plug-n-Play installation

• Easy installation

• Reliable secured and robust

radio link

• Frequency Band: 433 MHz,

868MHz, 915 MHz

• High performance, energy

efficient system

ecoSTAR Basic system includes Control

Panel (with Modbus RS-485 / TCP-IP,

Repeater, Wireless Transducers with

Enroll / Test button for quality of link).

Each transducer has a LED with few

colors that shows the quality of the

link.

Configuration is done via the keyboard

on the Control Panel (no need for

special software to configure the sys-

tem). The Control Panel has lighted

screen. The wireless transducers

configuration is realized 4 basic steps.

The structure of the Wireless

Transducers allows to integrate most

sensors in the market.

Temperature & HumidityMeasurementsin Warehouses

Millivolts Measurementfor Cathodic Protection

Low PressureMeasurement inClean Rooms

TemperatureMeasurements inPharma Process

Control Panel

Wireless Sensor

Repeater

Wireless SensorWireless Sensor

Enroll / TestButton

LED

Modbus RTU orModbus TCP/IP

Temperature & HumidityMeasurements inAgriculture

Measuring Pressure &Temperaturein Process

TemperatureMeasurement inLaboratories

Pressure Measurementin ChemicalProcess

ecoSTAR SCADA software

ecoSTAR offers a complete SCADA based solution for process engineers, system integrators,

or operators. ecoSTAR SCADA software features unparalleled ease of use, advanced graphics

capabilities and zero maintenance data logging, together with a proven high-performance

communication engine to deliver an affordable, superior SCADA experience.

• Simple to Setup• Ease of Use• Integrated Development and

Operation• Available from two points to

large projects (no limit of endpoints)

• Zero Maintenance DatabaseTables

The set-up and use of the ecoSTAR SCADA software are very easy and User Friendly. All

definitions are entered in simple to use tables,

allowing to export & import data, search and

replace values, sort through the definitions or

make global changes using the Express Edit fea-

ture.

ecoSTAR SCADA software always stays

responsive, even while performing lengthy tasks

such as records or searching for data, and the

streamlined -allowing you being updated. In fact,

ecoSTAR SCADA software is so easy to use that

most of our users have never bothered looking at

the documentation.

The ecoSTAR SCADA software Basic supports

one Control Panel – up to 30 end devices /

sensors. The NextView Project, is a SCADA

based software for projects with unlimited

tags / end devices.

Temperature & Humidity

in Different EnvironmentsMeasurements

Level inSewage Ponds

Measurement Level inChemical Process

Measurement Temperature Sensors

for Food Industries

ecoSTAR-Family AnalogThe ecoSTAR-Family Analog includes various sensors with analogue (4~20mA) output like

Pressure, Level, Humidity, Temperature etc. Temperature sensors (RTD, Thermocouple and

termistors), as well as accessories, like diaphragm seals for pressure instruments, thermowells

for temperature sensors, etc.

We manufacture and offer a

wide range of sensors, fit to

all type of industry and

applications: Steel-works,

Refineries, Chemicals,

Power Plants, Food

industries, Agriculture,

Pharmaceuticals and other

industries.

Our sensors work in

extreme working conditions

and are supplied with a

large range of process,

materials and electrical

connections.

ecoSTAR-Family

Analog is suit-

able for:

•

•

•

•

•

•

•

•

Temperature

Humidity

Pressure

Flow

Vibration

Level

Millivolt

Others

ecoSTAR-Family can be

made from the following

materials:

•

•

•

•

•

•

•

•

Stainless Steel

Hastelloy

Tantalum

PVC

PVDF

PP

Teflon

and others

Float Level Switch inTextile process

RF Level Switch forPowder in Tanks

RF Level switch forFoam Detection

Magnetic Flow Switchin Main Pipes

ecoSTAR-Family SwitchThe ecoSTAR-Family Switch includes various On/Off sensors

like level Floats, Level RF Switches and Flow Switches.

We manufacture standard switches and tailor made switches.

Our switches are capable of working with most of the media

and process procedures.

• Custom Made

• Suitable for all kinds of process procedures

Main Application Advantages:

� Foam Detection

� Water in Oil identification

� Working in powders (cement, lime, gypsum, etc.)

� Light /Very Light media (styrofoam, plastic raw

materials, wooden flakes, etc.)

Suitable for sticky and aggressive materials

�

S E N S O R S & W I R E L E S S

We are committed to our customer needs and offer tailor made sensors with highestquality to meet our customer requirements.

Our systems are already installed in the following applications: Cathodic Protection,Vibration Measurement, Low Pressure measurement in Clean Rooms, Temperature &Humidity measurement in Warehouses, Pressure monitoring of pump in field, LeakingDetection in Fuel tanks, etc.

Our products meet and service requirements in wide range of industries like:Agriculture, Power Plants, Chemicals, Food, Seawater desalination, Water treatment,water & sewage systems, etc. Our Products suitable for all types of media – liquids(clean and dirty), bulk solids, foams etc.

Tel:+604-397 0686 Fax:+604-398 4681

CLOUDOR

Wireless SensorWireless SensorWireless SensorWireless SensorWireless Sensor

ControlPanel

Repeater

Modbus RTU orModbus TCP/IP GPRS

CellPhone

SmartPhone

PC

No. G-03-A, 3000 Jalan Baru, Perai Plaza, 13600 Prai, P.W., Malaysia.

ecoSTAR SMC-485/xxx

Smart Control Panel Radio & Modbus RTU

Description:

The ecoSTAR SMC-485 Series is a complete wireless monitoring system. The Control Panel, SMC-485/XXX acts as a gateway between the wireless network and SCADA software in control room. Fea-tures:

• User friendly •Device registration & monitoring •Network Configuration •Up to 30 remote devices •Statisticas of link monitoring quality •Modulating Frequency GFSK •Frequency: 433MHz, 868MHz,

915MHz• MODBUS RTU

Features:

The ecoSTAR SMC-485 Series is a wireless network system consisting of different wireless modules transmitting in the unlicensed frequency (433MHz, 868 MHz, etc) to the Control Panel. The modules for measuring RTD, 4-20mA and digital signals transmit the readings to the Control Panel SMC-485/XXXacting as a gateway and providing tools for: - Device registration, removal or replacement - Devices' configuration (reporting period, stabilization time, thresholds, etc.) - Devices' monitoring (battery status, sensor signal quality, keep-alive signal, etc.) - On-going (24 hours) statistical quality of link monitoring - On-demand quality of link testing - Periodic device testing.

Specifications:

Wireless Network Topology Star Network with Multiple Hops Number of Endpoints 30 per Control Panel Modulation Frequency Hopping Spread Spectrum, GFSK Frequency Bands Versions for unlicensed Bands: 433 MHz, 868MHz, 915 MHzOutput Power Automatically Adjusted, up to 20dBm (100mW) Receiver Sensitivity 105dBm Range Line of Sight 1,500m' Indoor Typical 50m' to 100m' Current Consumption 40mA Power Source External 220VAC or 110VAC Internal backup battery Backup Power Source 4.8V NiMH rechargeable battery pack Backup Battery Operation 24 hours without recharge Enclosure Rating IP40 Operating Temperature -30°C to +70°C, up to 90% relative humidity Application Protocol MODBUS RTU

ecoSTAR SMR-500/xxx

Smart Repeater

Description:

The two way Repeater is needed whenever the transmission signal is too low. The Repeater version is available for range extension.

Features:

- The Repeater transceiver acts as a range extender for sensor transceivers to reach the Control Panel from a longer distance.

- It has the same form factor as the Control Panel.

- Repeaters are configured wirelessly from the coordinator.

Specifications:

Wireless Network Topology Star Network with Multiple Hops Number of Endpoints 30 per Control Panel Modulation Frequency Hopping Spread Spectrum, GFSK Frequency Bands 433 MHz, 868MHz, 915 MHzOutput Power Automatically Adjusted, up to 20dBm (100mW) Receiver Sensitivity -105dBm Range Line of Sight 1,500m' Indoor Typical 50m' to 100m' Current Consumption 40mA Power Source External 220VAC or 110VAC Internal backup battery Backup Power Source 4.8V NiMH rechargeable battery pack Backup Battery Operation 24 hours without recharge Enclosure Rating IP40 Operating Temperature -30°C to +70°C, up to 90% relative humidity

ecoSTAR SMD-010/xxx Smart Digital / On-Off Sensor

Description:

This ecoSTAR smart sensor transceiver is part of the Smart Sensor Transceivers fami-ly that connects to a variety of industrial sensors, for the purpose of remote wireless monitoring and control. A robust and efficient wireless link is the basis to migrating from cabling to wireless data collection, or in some cases for starting to monitor data at points where it was not previously feasible.

The SMD-010 transceiver connects to digital output (dry contact).

Features:

The SMD-010/XXX integrated sensor, connected to a superior performance two-way radio with an internal antenna, housed in an industrial ruggedized enclosure. Designed for ultra-low power consumption, the transceiver combines long range and reliable communication with long battery life. Device registration, configuration, control and time synchronization, are done remotely by the system so that field programming is not required. Upon activation, the transceiver begins to sample and transmit data, with the following options:

- Readings transmitted at specified time intervals

- Readings transmitted at scheduled times

- Remote interrogation for on-demand reading of the sensor

Specifications:

Wireless Network Topology Star Network with Multiple Hops Number of Endpoints 30 per Control Panel Modulation Frequency Hopping Spread Spectrum, GFSK Frequency Bands 433 MHz, 868MHz, 915 MHzOutput Power Automatically Adjusted, up to 20dBm (100mW) Receiver Sensitivity -105dBm Range Line of Sight 1,500m' Indoor Typical 50m' to 100m' Standby Current 5µA Transmit Current 150mA Receive Current 27mA Power Source 2x CR123A Lithium battery Reporting Period 1 sec to 12 h, remotely programmable over-the-air Battery Life 5 years for Reporting Period of 1 minute Operating Temperature -30°C ~ +70°C, up to 90% relative humidity Input Type Digital: Dry Contact (Form- A)

ecoSTAR SMP-100/xxx

Smart Sensor PT100

Description:

This ecoSTAR smart sensor transceiver is part of the Smart Sensor Transceivers family – that connects to a variety of industrial sensors, for the purpose of remote wireless monitoring and control. A robust and efficient wireless link is the basis to migrating from cabling to wireless data collection, or in some cases for starting to monitor data at points where it was not previously feasible. The SMP-100 transceiver connects to an RTD (Pt100) sensor.

Features:

The SMP-100/XXX integrated sensor, connected to a superior performance two-way radio with an internal antenna, housed in an industrial ruggedized enclosure. Designed for ultra-low power consumption, the transceiver combines long range and reliable communication with long battery life. Device registration, configuration, control and time synchronization, are done remotely by the system so that field programming is not required. Upon activation, the transceiver begins to sample and transmit data, with the following options:

- Readings transmitted at specified time intervals

- Readings transmitted at scheduled times

- Remote interrogation for on-demand reading of the sensor

Specifications:

Wireless Network Topology Star Network with Multiple Hops Number of Endpoints 30 per Control Panel Modulation Frequency Hopping Spread Spectrum, GFSK Frequency Bands 433 MHz, 868MHz, 915 MHz Output Power Automatically Adjusted, up to 20dBm (100mW) Receiver Sensitivity -105dBm Range Line of Sight 1,500m' Indoor Typical 50m' to 100m' Standby Current 5µA Transmit Current 150mA Receive Current 27mA Power Source 2x CR123A Lithium battery Reporting Period 1 sec to 12 h, remotely programmable over-the-air Battery Life 5 years for Reporting Period of 1 min Operating Temperature -30°C ~ +70°C, up to 90% relative humidity Input Type RTD: PT100 2-wire or 3-wire Measured Value Resolution 0.01% of full range (0.1°C) – at 25°C ambient temp.

ecoSTAR SMT-420/xxx

Smart Sensor Analog Transceiver

Description:

This smart sensor transceiver is part of the Smart Sensor Transceivers family – that connects to a variety of industrial sensors, for the purpose of remote wireless monitoring and control. A robust and efficient wireless link is the basis to migrating from cabling to wireless data collection, or in some cases for starting to monitor data at points where it was not previously feasible. The SMT-420 transceiver connects to a 4-20mA current loop.

Features:

The SMT-420/XXX integrated sensor, connected to a superior performance two-way radio with an internal antenna, housed in an industrial ruggedized enclosure. Designed for ultra-low power consumption, the transceiver combines long range and reliable communication with long battery life. It accurate wireless monitoring of 4-20 mA sensor data. Device registration, configuration, control and time synchronization, are done remotely by the system so that field programming is not required. Upon activation, the transceiver begins to sample and transmit data, with the following options:

- Readings transmitted at specified time intervals

- Readings transmitted at scheduled times

- Remote interrogation for on-demand reading of the sensor

Specifications:

Wireless Network Topology Star Network with Multiple Hops Number of Endpoints 30 per Control Panel Modulation Frequency Hopping Spread Spectrum, GFSK Frequency Bands 433 MHz, 868MHz, 915 MHzOutput Power Automatically Adjusted, up to 20dBm (100mW) Receiver Sensitivity -105dBm Range Line of Sight 1,500m' Indoor Typical 50m' to 100m' Standby Current 5µA Transmit Current 150mA Receive Current 27mA Power Source 2x CR123A Lithium battery Reporting Period 1 sec to 12 h, remotely programmable over-the-air Battery Life 5 years for Reporting Period of 1 minute Operating Temperature -30°C ~ +70°C, up to 90% relative humidity Input Type Analog 4-20mA current loop Measured Value Resolution Current Loop Input: 0.1% of Full Scale Input Voltage 16VDC Awakening Time 0.1sec.

005MS ISO/TEC 17021:2006

QS 18112006 CS 04

Certificate No: SG06/0893 MY06/0194

NEW Technology in Market Compact Recorder Controller

PRODUCTS OVERVIEW

Head Office :

No. 35-G, Jalan OP 1/2, Pusat Perdagangan One Puchong, Off Jalan Puchong, 471650 Puchong, Selangor Darul Ehsan, Malaysia.Tel : +603-8071 6322 (Hunting Line) Fax : +603-8071 6822 Email : info@dpstar.com.my

Holdings Sdn. Bhd. (678101-A)

Puchong Office :

No. 35-G, Jalan OP 1/2, Pusat Perdagangan One Puchong, Off Jalan Puchong, 471650 Puchong, Selangor Darul Ehsan, Malaysia.Tel : +603-8071 6722 (Hunting Line) Fax : +603-8071 5633 Email : info@dpstar.com.my

Thermo Control Electric Sdn. Bhd. (387517-A)

Penang Office :

No. G-03-A, 3000 Jalan Baru, Perai Plaza, 13600 Prai, P.W., Malaysia.Tel : +604-397 0686 (Hunting Line) Fax : +604-398 4681 Fax : +605-549 9318 (Ipoh) Email : info@dpstar.com.my

Thermo Control Electric (Penang)Sdn. Bhd. (387520-A)

Johor Bahru Office :

No. 46, Jalan Ros Merah 2/17, Taman Johor Jaya, 81100 Johor Bahru, Johor, Malaysia.Tel : +607-353 8218 (Hunting Line) Fax : +607-353 8120 Email : info@dpstar.com.my

Thermo Control Electric (JB) Sdn. Bhd. (408556-V)

Puchong Office :

No. 35-G, Jalan OP 1/2, Pusat Perdagangan One Puchong, Off Jalan Puchong, 471650 Puchong, Selangor Darul Ehsan, Malaysia.Tel : +603-8071 6122 (Hunting Line) Fax : +603-8071 6922 Email : info@dpstar.com.my

Electroheat Sdn. Bhd. (558023-D)

Puchong Office :

No. 37-G, Jalan OP 1/2, Pusat Perdagangan One Puchang, Off Jalan Puchong, Selangor Darul Ehsan, Malaysia.Tel : +603-8070 8788 (Hunting Line) Fax : +603-8070 8766 Email : dpstarte@dpstar.com.my

Thermo Electric Sdn. Bhd. (618662-M)

Manufacturing Centre :

No. 3, Jalan 6/118C, Desa Tun Razak, Cheras, 56000 Kuala Lumpur, Malaysia.Tel : +603-9173 7500 (Hunting Line) Fax : +603-9173 8500 Email : info@dpstar.com.my

Manufacturing Sdn. Bhd. (382800-K)

Puchong Centre :

No. 37-3, Jalan OP 1/2, Pusat Perdagangan One Puchang, Off Jalan Puchong, Selangor Darul Ehsan, Malaysia.Tel : +603-8076 9793 Fax : +603-8076 9739 Email : info@dpstar.com.my

Drive Solution Sdn. Bhd. (804358-A)

Visit us at http://www.dpstar.com.my

Call Us for Better Service Now!!!Call Us for Better Service Now!!!Call Us for Better Service Now!!!