1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E F F G G H H FINISH OF CHAMFERS AND FILLETS TO CONFORM TO ROUGHEST ADJACENT AREA. SURFACE ROUGHNESS MAXIMUM PER ASME B46.1. FULL THREAD DEPTHS ARE MINIMUM. DIMENSIONING AND TOLERANCING PER ASME Y14.5-2009 THREADS PER ASME B1.1 GAGING SYSTEM 21 U.O.S., ANSI B1.20.1 & B1.20.3 HEAT TREATMENT ENG. REF: TITLE DWN BY CK'D BY SIZE SHEET DWG.NO. ENGR. APPROVAL REV SCALE OF THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOL. ON DECIMALS: .X = .05 TOL. ON DECIMALS: .XX = .02 TOL. ON DECIMALS: .XXX = AS SPECIFIED TOL. ON ANGLES: ± 0 -30' CONFIDENTIAL - THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF GARDNER DENVER, INC. IT IS NOT FOR PUBLIC DISCLOSURE. POSSESSION OF THE INFORMATION DOES NOT CONVEY ANY RIGHT TO LOAN, SELL OR DISCLOSE THE INFORMATION. UNAUTHORIZED REPRODUCTION OR USE OF THE INFORMATION IS PROHIBITED. THIS DOCUMENT IS TO BE RETURNED TO GARDNER DENVER, INC. UPON THE COMPLETION OF THE PURPOSE FOR WHICH IT IS LOANED OR UPON REQUEST. Gardner Denver Inc. Quincy, IL. 1 1 E B KWT DA 7/2/2010 7/2/2010 313CAS800 DA OUTLINE-BARE UNIT VR3-8, VR5-8, VR7F-8 1/5 REVISION HISTORY ZONE REV DESCRIPTION DATE DWN CHK A RELEASED PER ECN 1052821 B INDICATED OPTIONAL EQUIPMENT: ECN 1065607 1-30-12 KWT DA 4X .69 X 1.06 SLOT MANUAL TANK DRAIN 1/4" NPT 75.00 34.87 26.71 34.25 STARTER (OPTIONAL) PRESSURE SWITCH PRESSURE GUAGE ASME PRESSURE RELIEF VALVE COMPRESSOR: R15 MOTOR: 3HP (VR3-8) 5HP (VR5-8) 7.5HP (VR7F-8) AIR COOLED AFTERCOOLER (OPTIONAL) 45° 90° 1/2" NPT VALVE 80 GALLON ASME RECEIVER 22.26 B.C. 25.14 13.13 AUTOMATIC TANK DRAIN (OPTIONAL) NOTES: 1. DO NOT SCALE DRAWING. 2. SPECIFICATIONS AND DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION. 3. ALL DIMENSIONS IN INCHES. 4. ADD 1.00" TO HIEGHT FOR VIBRATION OPTION.

SCALE OF - Compressor Services · 2017-04-22 · surface roughness maximum per asme b46.1. full thread depths are minimum. dimensioning and tolerancing per asme y14.5-2009 threads

Download PDF Report

Upload
others
View
23
Download
0

Embed Size (px)

Citation preview

Page 1: SCALE OF - Compressor Services · 2017-04-22 · surface roughness maximum per asme b46.1. full thread depths are minimum. dimensioning and tolerancing per asme y14.5-2009 threads

A A

B B

C C

D D

E E

F F

G G

H H

FINISH OF CHAMFERS AND FILLETS TO CONFORM TO ROUGHEST ADJACENT AREA.SURFACE ROUGHNESS MAXIMUM PER ASME B46.1.FULL THREAD DEPTHS ARE MINIMUM.

DIMENSIONING AND TOLERANCING PER ASME Y14.5-2009THREADS PER ASME B1.1 GAGING SYSTEM 21 U.O.S., ANSI B1.20.1 & B1.20.3

HEAT TREATMENT ENG. REF:

TITLE

DWN BY

CK'D BY

SIZE

SHEET

DWG.NO.ENGR. APPROVAL REV

SCALE OF

THIRD ANGLEPROJECTION

UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN INCHES

TOL. ON DECIMALS: .X = .05TOL. ON DECIMALS: .XX = .02TOL. ON DECIMALS: .XXX = AS SPECIFIEDTOL. ON ANGLES: ± 0 -30'

CONFIDENTIAL - THE INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF GARDNER DENVER, INC. IT IS NOT FOR PUBLIC DISCLOSURE. POSSESSION OF THE INFORMATION DOES NOT CONVEY ANY RIGHT TO LOAN, SELL OR DISCLOSE THE INFORMATION. UNAUTHORIZED REPRODUCTION OR USE OF THE INFORMATION IS PROHIBITED. THIS DOCUMENT IS TO BE RETURNED TO GARDNER DENVER, INC. UPON THE COMPLETION OF THE PURPOSE FOR WHICH IT IS LOANED OR UPON REQUEST.

Gardner Denver Inc.Quincy, IL.

1 1

E BKWT

DA 7/2/2010

7/2/2010 313CAS800DA

OUTLINE-BARE UNITVR3-8, VR5-8, VR7F-8

1/5

REVISION HISTORY

ZONE REV DESCRIPTION DATE DWN CHK

A RELEASED PER ECN 1052821

B INDICATED OPTIONAL EQUIPMENT: ECN 1065607 1-30-12 KWT DA

4X .69 X 1.06 SLOT