Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
SAM 010-130 DIN is a series of light weight casing axial piston motors, particularly suitable for mobile hydraulics. SAM 010-130 DIN is of the bent-axis type with spherical pistons.
The design gives a compact motor with few moving parts, high starting torque and high operational reliability. It covers the entire displacement range 10-130 cmᶟ/rev. with max. pressure 400 bar.
It´s high level of reliability is due to the choice of materials, hardening methods, surface structures and the quality assured manufacturing process.
Other advantages:
• Light weight metal casing design
• Smooth operation over the entire speed range
• High efficiency
• Suitable for applications with high angular accelerations due to its high rotary stiffness
• Corrosion free light metal-housing
• Less heat generation due to better ability to dissipate heat through housing
SAM 010-130 DIN
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 1/7
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
Line
SA Sunfab Aluminium
1. Type
M Motor
2. Displacement
010 012 017 025 034 040 047 056 064 084 090 108 130
3. Direction of rotation
W Independent
4. Sealing
N Nitrile
5. Mounting flange
ISO 7653-D
DL4 ø 80
6. Shaft
DIN 5462 / ISO 14
L35 8x32x34.9
X = Standard, preferred O = Contact Sunfab
7. Connection cover
010 012 017 025 034 040 047 056 064 084 090 108 130
S3 40° threaded connection
X X X X X X X X X X X X X
8. Connections
010 012 017 025 034 040 047 056 064 084 090 108 130
G ISO G X X X X X X X X X X X X X
9. Additional
1 External drainage
10. Speed sensor
010 012 017 025 034 040 047 056 064 084 090 108 130
00 No speed sensor
X X X X X X X X X X X X X
Versions, main data Example
SA M - 012 W - N - DL4 - L35 - S3 G - 1 00
Line 1 2 3 4 5 6 7 8 9 10
Motor SAM 010-130 DIN 010 012 017 025 034 040 047 056 064 084 090 108 130
Displacement cm3/rev 9.6 12.6 17.0 25.4 34.2 41.2 47.1 56.7 63.5 83.6 90.7 108.0 130.0
Working pressuremax intermittentmax continuous
bar 400350
400350
400350
400350
400350
400350
400350
400350
400350
400350
400350
400350
330280
Revolutionsmax intermittentmax continuousmin continuous
rpm 30002400
300
30002400
300
30002400
300
30002400
300
30002400
300
25002000
300
25002000
300
25002000
300
25002000
300
20001600
300
20001600
300
20001600
300
20001600
300
Powermax intermittentmax continuous
kW 1411
1814
2419
3629
4939
5746
6552
7862
8870
9374
10081
12096
12499
Starting torque theoretical value Nm/bar 0.15 0.20 0.27 0.40 0.54 0.66 0.75 0.89 1.0 1.33 1.44 1.71 2.06
Moment of inertia (x 10-3) kg m2 0.9 0.9 0.9 1.1 1.1 2.6 2.6 2.6 2.6 7.4 7.4 7.4 7.4
Max intermittent housing pressure bar 5 5 5 5 5 5 5 5 5 5 5 5 5
Weight kg 6.9 6.9 6.9 7.1 7.1 9.9 9.9 9.9 9.9 13.8 13.8 13.8 13.8
Intermittent operation refers to a max of 6 seconds per minute, representing e.g. peaks in rotational speed during unloading and acceleration.
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 2/7
SAM 010-130 DIN
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
AF F20° 20°
B
D x n1000 x ηv
Q x 1000 x ηv
D
D x ∆p x ηhm
6.3
Q x ∆p x ηt
60
General instructions
Shaft loadsThe service life of the motor largely depends on the service life of the bearings. These are affected by the operating conditions such as speed, pressure, oil viscosity and degree of purification.
InstallationThe motor housing is filled with oil to at least 50% of the volume before start up. The drainage hose is connected to the drainage outlet positioned highest on the motor. The other end is connected below the oil level in the oil tank.
Radial load (N)
Bear
ing
serv
ice
life
(h)
Pressureclockwise
rotation
Pressureanti-clockwiserotation
Optimal angle of attackfor radial loads
External loading of the shaft, its size, direction and location also affect the service life of the bearings.
If a calculation of bearing service life is required for special applications, contact Sunfab Hydraulics.
D = displacement, cm3⁄rev
n = revolutions, rev ⁄min
P = power, kW
Q = flow, litre ⁄min
ηv = volumetric efficiency
ηhm = hydromechanical efficiency
ηt = total efficiency = ηv x ηhm
M = torque, Nm
∆p = pressure difference between inlet and outlet on the hydraulic motor, MPa
Hydraulic fluidsHigh performance oil meeting the specifications of ISO type HM, DIN 51524-2HLP or better must be used.Min. viscosity 10 cSt is required to guarantee lubrication. Ideal viscosity is 20 - 40 cSt.
Pipe dimensionsThe recommended flow velocity in the pressure line is max 7 m/sec.
FilteringCleanliness ISO norm 4406, code 16/13 is recommended.
Useful formulaes
Required flow rate Q = litres⁄min.
Speed n = RPM
Torque M = Nm
Power P = kW
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 3/7
SAM 010-130 DIN
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
DL4 ISO 7653-D
L35 DIN 5462 / ISO 14
Millimeter (inch)
Dimensions SAM 010-034
Flange, shaft & connection cover
S3G
ISO G3/4 (2x)113
4.45
186 7.31
206 8.1
742.93
102
4.03
97 3.82
M12
SPLINE 8x32x34,9
28 1.1
50 1.97
7,5 0.3
71 2.79
O80
-0,030
-0,060
3.15-0.001
-0.002
ISO G1/2
742.93
40°
98 3.86
106 4.17
13,5 0.53
803.15
q
115
4.52
55 2.16
12 0.46
O13
0.51
(4x)
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 4/7
SAM 010-130 DIN
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
DL4 ISO 7653-D
Millimeter (inch)
Dimensions SAM 040-064
Flange, shaft & connection cover
L35 DIN 5462 / ISO 14 S3G
40°69,9
2.75
13,1 0.51
7,5 0.3
85 3.35
O80
-0,030
-0,060
3.15-0.001
-0.002
98 3.86
106 4.17
O13
0.51
(4x)
SPLINE 8x32x34,9
M12
28 1.1
50 1.97
110 4.33
ISO G3/4 (2x)
843.32
114
4.47
214 8.41
234 9.22
122,8
4.84
803.15
q 114,5
4.51
55 2.15
12 0.46
ISO G1/2
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 5/7
SAM 010-130 DIN
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
DL4 ISO 7653-D
Millimeter (inch)
Dimensions SAM 084-130
Flange, shaft & connection cover
L35 DIN 5462 / ISO 14 S3G
M12SPLINE 8x32,34,9
28 1.1
55 2.15
ISO G1 (2x)139
5.47
58 2.28
118 4.65
236 9.28
264 10.41
953.74
133
5.23
793.1
40°
7,5 0.3
15 0.59
91 3.6
803.15
q
115
4.52
98 3.86
106 4.17
O13
0.51
(4x)
O80
-0,030
-0,060
3.15-0.001
-0.002
12 0.46
ISO G1/2
3205GB1706 1.0 - Printed: 05/06/2020 10:24:37 - Page 6/7
SAM 010-130 DIN
Sunfab Hydraulics AB, Box 1094, SE-824 12 Hudiksvall, Sweden. Tel: +46 650-367 00, Fax: +46 650-367 27, E-mail: [email protected] Web: www.sunfab.com
WARNINGWARNINGWARNINGWARNING
When the motor is in use:
1. Do not touch the pressure pipe
2. Beware of rotating parts
3. The motor and pipes can reach high temperatures
Sunfab reserves the right to make changes in design and dimensions without notice. Printing and typesetting errors reserved.© Copyright 2015 Sunfab Hydraulics AB. All Rights Reserved.
SAM 010-130 DIN
GB - Printed: 05/06/2020 10:24:37 - Page 7/7