Daniamant design and manufacture all of our products in line with the

relevant worldwide approvals, technical specifications, current legislation and

International directives.

Our mission is to achieve World class performance through partnerships with

our suppliers, customers and employees, providing products and services that

enhance the safety and security of our customers.

Daniamant products cover 12 key areas:• Lifejacket Lights

• Liferaft Lights• Lifebuoy Lights

• Intrinsically Safe Lights• Special Lights

• LED Flares• Forward Looking Sonars (FLS)

• Bridge Navigational Watch Alarm System (BNWAS)

• Salinometers• Oil Level Alarm

• Electronic Inclinometer• Agency for a range of world-renowned

safety product brands (supplied to the Danish market)

Further InformationFor further information on our

products, please see our website: www.daniamant.com

Salinometer for FreshwaterGenerators and BoilersSL8005

BROCHURE

www.daniamant.com

Be safe at sea

Function The salinometer measures and supervises the salinity (salt content) by conductivity measurement in fresh water. The measured value is displayed as ppm and by comparing the measured value to a user defined alarm setpoint value, relay outputs are available to indicate if salinity is above or below the alarm setpoint value.

Typical UseIn areas where fresh water generation or purification is taking place and level of salinity in the fresh water must be monitored as well as in areas where a set level of salinity is requested in a process. Salinometers are used in: Freshwater Generators, Boilers, Reversed Osmosis Fresh Water Systems (RO) and other systems where salinity has to be supervised.

Mains Supply85 - 265 V AC, 50/60 Hz, 10 VA typ. - 15 VA max.

Mains supply must be protected against overcurrent by an external 250 mA slow-blow fuse.

Measuring Salinity RangeMeasuring salinity range: 0 - 200 ppm, displayed as “000” to “199” and “HI” if value exceeds 200 ppm.

Alarm FunctionUser defined alarm setpoint value (0 - 199 ppm) is set using “+” and “-“ buttons. When measured value exceeds alarm setpoint, change-over relay contacts A and B are activated. Alarm relay B may be enabled/disabled from the front by pressing a button.

SL8005 in wallbox

Electrode unit

SL8005 for panel mounting

Daniamant Electronics A/SIndustrivej 24C3550 Slangerup

Denmark

Tel +45 47 37 38 00Fax +45 47 37 38 09

info@daniamant.com

Daniamant LtdUnit 3, The Admiral Park

Airport Service RoadPortsmouth, PO3 5RQ

United Kingdom

Tel +44 23 92 67 51 00Fax +44 23 92 67 51 01

sales@daniamant.com

www.daniamant.com

Relay Contacts2 x Change-over relay contacts – capable of handling 4A (85 - 265 V AC or 24 V DC) load. Relays must be protected against overcurrent by an external 4 A slow-blow fuse.

TestFull electronics test when power is switched on and during run-time a test-button is available for testing the salinometers. The test-button will disable the electrode and feed an internal 10 ppm signal to the salinometer (note that this will be seen as an actual measurement, and alarms will respond to this). Connection to electrode is monitored and error in this reported on the front (malfunction + LED + display = “- - -“).

ProtectionSalinometer for panel mounting is IP65 from the front. Salinometer in wall mounting box is IP65.

Cable Connections1-2: Mains power input.3-5: Alarm relay A (change over function NO-C-NC)6-8: Alarm relay B (change over function NO-C-NC)11-15: Electrode.16-17: 4-20 mA output.

BROCHURE

Be safe at sea

Specifications SL8005

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

Panel mounting model

Wall mounting model 206

110 116

4519

5178,5

106133,5 161

212

Visit us at www.unielec.dk

As our products are subject to current improvements, the equipment may vary in details from specifications and descriptions given herein. This publication gives only a general description of the product(s) and shall not form part of any contract.

Amager S trandvej 124 · DK-2300 Copenhagen STel: +45 3286 0525 · Fax: +45 3258 1330mail: info@unielec.dk · www.unielec.dk

Electrode unit

Function:The salinometer measures and supervises thesalinity (salt content) by conductivity measurementin fresh water. The measured value is displayed asppm, and, by comparing the measured value to auser defined alarm setpoint value, relay outputs areavailable to indicate if salinity is above or below thealarm setpoint value.

Typical use:In areas where fresh water generation or purificationis taking place and level of salinity in the fresh watermust be monitored as well as in areas where a setlevel of salinity is requested in a process.Salinometers are used in: Freshwater Generators,Boilers, Reversed Osmosis Fresh Water Systems(RO) and other systems where salinity has to besupervised.

Mains supply:85 – 265 V AC, 50/60 Hz, 10 VA typ. - 15 VA max.

Mains supply must be protected against overcurrentby an external 250 mA slow-blow fuse.

Measuring range:0 – 200 ppm, displayed as “000” to “199” and “HI”if value exceeds 200 ppm.

Electrode-compatibility:5-wire auto-referenced Uni-Safe Electronicselectrode with built in temperature-compensation.

Alarm function:User defined alarm setpoint value (0 – 199 ppm) isset using stepped “+” and “-“ buttons.When measured value exceeds alarm setpoint,change-over relay contacts 1 and 2 are activated.Alarm relay 2 may be enabled/disabled from thefront by pressing a button.

Relay contacts:2x Change-over relay contacts – capable ofhandling 4A (85 – 265 V AC or 24 V DC) load.Relays must be protected against overcurrent by anexternal 4 A slow-blow fuse.

Test:Full electronics test on power on; and during run-time a test-button is available for testing theelectronics. The test-button will disable theelectrode and feed an internal 10 ppm signal to thesalinometer (note that this will be seen as an actualmeasurement, and alarms will respond to this).Connection to electrode is monitored, and error inthis reported on the front (LED + display = “- - -“).

Protection:Panel mounting units are IP65 from the front.Wall mounting is placed in an IP65 box.

Cable connections:1-2: Mains power input.3-5: Alarm relay 1 (change over function NO-C-NC)6-8: Alarm relay 2 (change over function NO-C-NC)11-15: Electrode.16-17: 4-20 mA output.

130 mm

18 mm

9996091 Løsblad 8005:1 27-08-2012 09:30 Side 2

Specifications SL8005

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

Panel mounting model

Wall mounting model 206

110 116

4519

5178,5

106133,5 161

212

Visit us at www.unielec.dk

As our products are subject to current improvements, the equipment may vary in details from specifications and descriptions given herein. This publication gives only a general description of the product(s) and shall not form part of any contract.

Amager S trandvej 124 · DK-2300 Copenhagen STel: +45 3286 0525 · Fax: +45 3258 1330mail: info@unielec.dk · www.unielec.dk

Electrode unit

Function:The salinometer measures and supervises thesalinity (salt content) by conductivity measurementin fresh water. The measured value is displayed asppm, and, by comparing the measured value to auser defined alarm setpoint value, relay outputs areavailable to indicate if salinity is above or below thealarm setpoint value.

Typical use:In areas where fresh water generation or purificationis taking place and level of salinity in the fresh watermust be monitored as well as in areas where a setlevel of salinity is requested in a process.Salinometers are used in: Freshwater Generators,Boilers, Reversed Osmosis Fresh Water Systems(RO) and other systems where salinity has to besupervised.

Mains supply:85 – 265 V AC, 50/60 Hz, 10 VA typ. - 15 VA max.

Mains supply must be protected against overcurrentby an external 250 mA slow-blow fuse.

Measuring range:0 – 200 ppm, displayed as “000” to “199” and “HI”if value exceeds 200 ppm.

Electrode-compatibility:5-wire auto-referenced Uni-Safe Electronicselectrode with built in temperature-compensation.

Alarm function:User defined alarm setpoint value (0 – 199 ppm) isset using stepped “+” and “-“ buttons.When measured value exceeds alarm setpoint,change-over relay contacts 1 and 2 are activated.Alarm relay 2 may be enabled/disabled from thefront by pressing a button.

Relay contacts:2x Change-over relay contacts – capable ofhandling 4A (85 – 265 V AC or 24 V DC) load.Relays must be protected against overcurrent by anexternal 4 A slow-blow fuse.

Test:Full electronics test on power on; and during run-time a test-button is available for testing theelectronics. The test-button will disable theelectrode and feed an internal 10 ppm signal to thesalinometer (note that this will be seen as an actualmeasurement, and alarms will respond to this).Connection to electrode is monitored, and error inthis reported on the front (LED + display = “- - -“).

Protection:Panel mounting units are IP65 from the front.Wall mounting is placed in an IP65 box.

Cable connections:1-2: Mains power input.3-5: Alarm relay 1 (change over function NO-C-NC)6-8: Alarm relay 2 (change over function NO-C-NC)11-15: Electrode.16-17: 4-20 mA output.

130 mm

18 mm

9996091 Løsblad 8005:1 27-08-2012 09:30 Side 2

Specifications SL8005

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

206 mm

168 mm

96 mm118 mm

4 mm

54 mm

9 mm

Panel mounting model

Wall mounting model 206

110 116

4519

5178,5

106133,5 161

212

Visit us at www.unielec.dk

As our products are subject to current improvements, the equipment may vary in details from specifications and descriptions given herein. This publication gives only a general description of the product(s) and shall not form part of any contract.

Amager S trandvej 124 · DK-2300 Copenhagen STel: +45 3286 0525 · Fax: +45 3258 1330mail: info@unielec.dk · www.unielec.dk

Electrode unit

Function:The salinometer measures and supervises thesalinity (salt content) by conductivity measurementin fresh water. The measured value is displayed asppm, and, by comparing the measured value to auser defined alarm setpoint value, relay outputs areavailable to indicate if salinity is above or below thealarm setpoint value.

Typical use:In areas where fresh water generation or purificationis taking place and level of salinity in the fresh watermust be monitored as well as in areas where a setlevel of salinity is requested in a process.Salinometers are used in: Freshwater Generators,Boilers, Reversed Osmosis Fresh Water Systems(RO) and other systems where salinity has to besupervised.

Mains supply:85 – 265 V AC, 50/60 Hz, 10 VA typ. - 15 VA max.

Mains supply must be protected against overcurrentby an external 250 mA slow-blow fuse.

Measuring range:0 – 200 ppm, displayed as “000” to “199” and “HI”if value exceeds 200 ppm.

Electrode-compatibility:5-wire auto-referenced Uni-Safe Electronicselectrode with built in temperature-compensation.

Alarm function:User defined alarm setpoint value (0 – 199 ppm) isset using stepped “+” and “-“ buttons.When measured value exceeds alarm setpoint,change-over relay contacts 1 and 2 are activated.Alarm relay 2 may be enabled/disabled from thefront by pressing a button.

Relay contacts:2x Change-over relay contacts – capable ofhandling 4A (85 – 265 V AC or 24 V DC) load.Relays must be protected against overcurrent by anexternal 4 A slow-blow fuse.

Test:Full electronics test on power on; and during run-time a test-button is available for testing theelectronics. The test-button will disable theelectrode and feed an internal 10 ppm signal to thesalinometer (note that this will be seen as an actualmeasurement, and alarms will respond to this).Connection to electrode is monitored, and error inthis reported on the front (LED + display = “- - -“).

Protection:Panel mounting units are IP65 from the front.Wall mounting is placed in an IP65 box.

Cable connections:1-2: Mains power input.3-5: Alarm relay 1 (change over function NO-C-NC)6-8: Alarm relay 2 (change over function NO-C-NC)11-15: Electrode.16-17: 4-20 mA output.

130 mm

18 mm

9996091 Løsblad 8005:1 27-08-2012 09:30 Side 2

Electrode-compatibility: auto-referenced electrode with built-in temperature-compensation and 2.5 m 5-wire marine approved cable.

SL8005 for panel mounting

Fittings and adapters

SL8005 in wallbox

Electrode unit