Click here to load reader

S7-1500 SIMATIC S7-1500 - Siemens

  • View
    332

  • Download
    34

Embed Size (px)

Text of S7-1500 SIMATIC S7-1500 - Siemens

  • S7-1500

    ___________________

    ___________________

    ___________________

    ___________________

    ___________________

    SIMATIC

    S7-1500

    Getting Started

    05/2014 A5E03981761-AC

    Welcome

    Automation task 1

    Hardware section 2

    Software section 3

    Security 4

  • Siemens AG Industry Sector Postfach 48 48 90026 NRNBERG GERMANY

    A5E03981761-AC 05/2014 Subject to change

    Copyright Siemens AG 2013 - 2014. All rights reserved

    Legal information Warning notice system

    This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

    DANGER indicates that death or severe personal injury will result if proper precautions are not taken.

    WARNING indicates that death or severe personal injury may result if proper precautions are not taken.

    CAUTION indicates that minor personal injury can result if proper precautions are not taken.

    NOTICE indicates that property damage can result if proper precautions are not taken.

    If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

    Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

    Proper use of Siemens products Note the following:

    WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

    Trademarks All names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

    Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

  • S7-1500 Getting Started, 05/2014, A5E03981761-AC 3

    Welcome

    Welcome Welcome to the Getting Started "TIA Portal V13".

    In this Getting Started, we show you an example of how to use the CPU SIMATIC S7-1500 with the TIA Portal to create an automation solution for a "color mixing plant". Video clips will illustrate the approach for creating a solution for the automation task.

    In the first part, you assemble the hardware and prepare your configuration PC.

    In the second part, you configure the CPU and HMI visualization using the example of a color mixing plant.

    In addition, you can find options and extensions for your automation solutions.

    Security information Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

    For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. You can find more information about industrial security on the Internet (http://www.siemens.com/industrialsecurity).

    To stay informed about product updates as they occur, sign up for a product-specific newsletter. You can find more information on the Internet (http://support.automation.siemens.com).

    http://www.siemens.com/industrialsecurityhttp://support.automation.siemens.com/

  • S7-1500 4 Getting Started, 05/2014, A5E03981761-AC

    Table of contents

    Welcome ................................................................................................................................................ 3

    1 Automation task ...................................................................................................................................... 7

    1.1 Introduction.................................................................................................................................... 7

    1.2 Sample project .............................................................................................................................. 8

    2 Hardware section .................................................................................................................................. 15

    2.1 Introduction.................................................................................................................................. 15 2.1.1 Requirements .............................................................................................................................. 15 2.1.2 Additional information .................................................................................................................. 16

    2.2 Installing the assembly ................................................................................................................ 17 2.2.1 Overview ..................................................................................................................................... 17 2.2.2 Installing the assembly ................................................................................................................ 17

    2.3 Wiring .......................................................................................................................................... 20 2.3.1 Overview ..................................................................................................................................... 20 2.3.2 Wiring rules ................................................................................................................................. 21 2.3.3 Wiring the mains connection plug ............................................................................................... 22 2.3.4 Wiring the load current supply (PM) to the CPU ......................................................................... 24 2.3.5 Potential bridge circuits ............................................................................................................... 25 2.3.6 Wiring the digital input module .................................................................................................... 25 2.3.7 Wiring the digital output module .................................................................................................. 27 2.3.8 Wiring front connectors ............................................................................................................... 29

    2.4 Power on ..................................................................................................................................... 31 2.4.1 Overview ..................................................................................................................................... 31 2.4.2 Power on ..................................................................................................................................... 31 2.4.3 Assign IP address via the display ............................................................................................... 33

    3 Software section ................................................................................................................................... 34

    3.1 Creating the project and hardware .............................................................................................. 34 3.1.1 Introduction to the TIA Portal ...................................................................................................... 34 3.1.2 Creating a project ........................................................................................................................ 36 3.1.3 Creating an S7-1500 CPU .......................................................................................................... 38 3.1.4 Running the hardware detection ................................................................................................. 40 3.1.5 Creating ET 200 interface modules ............................................................................................ 41 3.1.6 Networking ET 200 interface modules ........................................................................................ 42 3.1.7 Creating input and output modules

Search related