199
Last Modified Allgon Repeaters Repeater products Product list Standard Compact Combi Band Selective Band Selective Dual Band 800 MHz 800MHz Standard 900 MHz 900 MHz Compact 1800 MHz 1800 MHz 1900 MHz 1900 MHz EGSM Channel Selective (GSM) WCDMA 900 MHz Standard 1800 MHz 1900 MHz EGSM/RGSM CDMA LinDAS 1900 MHz Unit specification 800 MHz System specification Mechanical Drawings Options and features Standard Low Repeater Options & Features Standard High OMS Compact Low Fibre Optic Transceiver Compact High Fibre Optic Node Conformity Allgon Repeater Conformity Repeater Certificates

Repeater Specs

Embed Size (px)

DESCRIPTION

Repeaters

Citation preview

Page 1: Repeater Specs

Last Modified

Allgon Repeaters

Repeater productsProduct list

Standard Compact CombiBand Selective Band Selective Dual Band800 MHz 800MHz Standard900 MHz 900 MHz Compact1800 MHz 1800 MHz1900 MHz 1900 MHzEGSM

Channel Selective (GSM) WCDMA900 MHz Standard1800 MHz1900 MHzEGSM/RGSM

CDMA LinDAS1900 MHz Unit specification800 MHz System specification

Mechanical Drawings Options and featuresStandard Low Repeater Options & FeaturesStandard High OMSCompact Low Fibre Optic TransceiverCompact High Fibre Optic NodeConformityAllgon Repeater ConformityRepeater Certificates

Page 2: Repeater Specs

Standard 800 MHz Band Selective

Product Description

AR4200_052AR4200_053 25 MHz BWAR4600_052 IDEN

Page 3: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR4200/052-201

Rev

E

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR4200_052_E

Specification of a Band selective Repeater800 MHz

Product Number: AR4200/052

1. Electrical specification (typical value)The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs

Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 4 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 4: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR4200/053-201

Rev

B

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR4200_053_B

Specification of a Band selective Repeater800 MHz, 25 MHz BW versionProduct Number: AR4200/053

1. Electrical specification (typical values)The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25.0 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25.0 MHz Selectivity BW 20dB BW 3dB + 1.2 MHz Selectivity BW 30dB BW 3dB + 2.0 MHz Pass band ripple 6 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, max 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 5: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR4600/052-201

Rev

C

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR4600_052_C

Specification of a Band selective RepeaterIDEN, 800 MHz

Product number: AR4600/052

1. Electrical specification (typical values)The repeater complies with the requirements of FCC

Frequency band Up link 806 – 825 MHz Frequency band Down link 851 - 870 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 ºC 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 4 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, typ. (max) 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to + 131 F Casing class NEMA4/IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 174 x 209 x 69 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 6: Repeater Specs

Standard 900 MHz Band Selective

Product Description

AR1200_052 16,5 MHz BWAR1200_053 25 MHz BW

Page 7: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR1200/052-201

Rev

D

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR1200_052_D

Specification of a Band selective Repeater900 MHz

Product Number: AR1200/052

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 4 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 8: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-01-26

Godkänd/Approved Dok nr/Doc no

AR1200/053-201

Rev

A

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR1200_053_A

Specification of a Band selective Repeater900 MHz, 25 MHz Band WidthProduct Number: AR1200/053

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 6 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 9: Repeater Specs

Standard 1800 MHz Band Selective

Product Description

AR2200_001 Low BandAR2200_901 High Band

Page 10: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR2200/001-201

Rev

D

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR2200_001_D

Specification of a Band selective Repeater1800 MHz, Lower band

Product Number: AR2200/001

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1710 – 1765 MHz Frequency band Down link 1805 - 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously

Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 11: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR2200/901-201

Rev

D

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR2200_901_D

Specification of a Band selective Repeater1800 MHz, Upper band

Product Number: AR2200/901

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 - 1880 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW3 dB, 16.5 MHz 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 12: Repeater Specs

Standard 1900 MHz Band Selective

Product Description

AR3400_001 Low BandAR3400_901 High Band

Page 13: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR3400/001-201

Rev

CSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3400_001_C

Specification of a band selective repeater1900 MHz version, Lower bandProduct number: AR3400/001

1. Electrical specification (typical value)

The repeater complies with the FCC requirements

Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Passband ripple 5 dB Max output power + 36 dBm Output power 2 carrier + 30 dBm Automat gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, nom. (max) 130 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 14: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-20

Godkänd/Approved Dok nr/Doc no

AR3400/901-201

Rev

CSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3400_901_C

Specification of a band selective repeater1900 MHz version, Upper bandProduct number: AR3400/901

1. Electrical specification (typical values)

The repeater complies with FCC requirements

Frequency band Up link 1870 – 1910 MHz Frequency band Down link 1950 - 1990 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Max output power + 36 dBm Output power 2 carrier + 30 dBm Automat gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 VAC Power consumption, nom. (max) 130 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 15: Repeater Specs

Standard 800 MHz CDMA

Product Description AR4500_0014 2 Channel AR4500_0514 2 Channel, MRX AR4540_0514 2 Channel, High Power, MRX AR4200_012 Band selective, 25 MHz

Page 16: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-10-08

Godkänd/Approved Dok nr/Doc no

AR4500/0014-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4500_0014_A

Specification of a CDMA 800 channel selective repeater2-channel version, standard

Product Number: AR4500/0014

1. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation No Antenna VSWR supervision No Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 17: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-10-08

Godkänd/Approved Dok nr/Doc no

AR4500/0514-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4500_0514_A

Specification of a CDMA 800 channel selective repeater2-channel version, standard with MRX

Product Number: AR4500/0514

1. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation Yes (MRX) Antenna VSWR supervision Yes (MRX) Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 18: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-09-13

Godkänd/Approved Dok nr/Doc no

AR4540/0514-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4540_0514_A

Specification of a CDMA 800 channel selective repeater2-channel version, High Power with MRX

Product Number: AR4540/05141. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps), DL 65-95 dB Gain adjustment range (1 dB steps), UL 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation Yes (MRX) Antenna VSWR supervision Yes (MRX) Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 19: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-01-16 Godkänd/Approved

Dok nr/Doc no

AR4200/012-201 Rev

A Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4200_012_A.doc

Specification of a Band selective Repeater CDMA 800 MHz, 25 MHz BW version

Product Number: AR4200/012 1. Electrical specification (typical values) The repeater complies with the requirements of FCC Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25.0 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25.0 MHz Selectivity BW 20dB BW 3dB + 1.2 MHz Selectivity BW 30dB BW 3dB + 2.0 MHz Pass band ripple 6 dB Output power RMS, one carrier +33 dBm Output power RMS, two carrier +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 4 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 20: Repeater Specs

Standard 900 MHz GSM Channel Selective

Product Description

AR1100_002 2 ChannelAR1100_004 4 ChannelAR1111_006 6 ChannelAR1111_008 8 Channel

Page 21: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR1100/002-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1100_002_D

Specification of a GSM 900 channel selective repeater2-channel version

Product Number: AR1100/002

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 2 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 22: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR1100/004-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1100_004_D

Specification of a GSM 900 channel selective repeater4-channel version

Product Number: AR1100/004

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 4 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 23: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR1111/006-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1111_006_D

Specification of a GSM 900 channel selective repeater6-channel version

Product Number: AR1111/006

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 6 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 24: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR1111/008-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1111_008_D

Specification of a GSM 900 channel selective repeater8-channel version

Product Number: AR1111/008

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 8 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 174 x 209 x 94 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 25: Repeater Specs

Standard 1800 MHz GSM Channel Selective

Product Description

AR2100_002 2 Channel, Low BandAR2100_004 4 Channel, Low BandAR2100_902 2 Channel, High BandAR2100_904 4 Channel, High BandAR2121_006 6 Channel, Low BandAR2121_008 8 Channel, Low BandAR2121_906 6 Channel, High BandAR2121_908 8 Channel, High Band

Page 26: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2100/002-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2100_002_D

Specification of a GSM 1800 channel selective repeater2-channel version, Lower bandProduct Number: AR2100/002

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Page 27: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2100/004-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2100_004_D

Specification of a GSM 1800 channel selective repeater4-channel version, Lower bandProduct Number: AR2100/004

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 4 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55°C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 28: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2100/902-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2100_902_D

Specification of a GSM 1800 channel selective repeater2-channel version, Upper bandProduct Number: AR2100/902

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 – 1880 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 29: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2000-12-27 Godkänd/Approved

Dok nr/Doc no

AR2100/904-201 Rev

D Sida/Page

1 Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

AR2100_904_D.doc

Specification of a GSM 1800 channel selective repeater

4-channel version, Upper band Product Number:AR2100/904

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 – 1880 MHz Number of channels 4 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Page 30: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/006-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_006_D

Specification of a GSM 1800 channel selective repeater6-channel version, Lower bandProduct Number: AR2121/006

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 6 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 31: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/008-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_008_D

Specification of a GSM 1800 channel selective repeater8-channel version, Lower bandProduct Number: AR2121/008

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 8 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 32: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/006-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_006_D

Specification of a GSM 1800 channel selective repeater6-channel version, Lower bandProduct Number: AR2121/006

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 6 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 33: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/008-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_008_D

Specification of a GSM 1800 channel selective repeater8-channel version, Lower bandProduct Number: AR2121/008

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 8 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 34: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/906-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_906_D

Specification of a GSM 1800 channel selective repeater6-channel version, Upper bandProduct Number: AR2121/906

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 – 1880 MHz Number of channels 6 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 35: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-27Godkänd/Approved Dok nr/Doc no

AR2121/908-201Rev

DSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR2121_908_D

Specification of a GSM 1800 channel selective repeater8 channel version, Upper bandProduct Number: AR2121/908

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300609-4 Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 – 1880 MHz Number of channels 8 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 36: Repeater Specs

Standard 1900 MHz GSM Channel Selective

Product Description

AR3100_002 2 Channel, Low BandAR3100_004 4 Channel, Low BandAR3100_902 2 Channel, High BandAR3100_904 4 Channel, High BandAR3131_006 6 Channel, Low BandAR3131_008 8 Channel, Low BandAR3131_906 6 Channel, High BandAR3131_908 8 Channel, High Band

Page 37: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3100/002-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3100_002_D

Specification of a GSM 1900 channel selective repeater2-channel version, Lower bandProduct Number: AR3100/002

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 38: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3100/004-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3100_004_D

Specification of a GSM 1900 channel selective repeater4-channel version, Lower bandProduct Number: AR3100/004

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 155 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 39: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3100/902-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3100_902_D

Specification of a GSM 1900 channel selective repeater2-channel version, Higher bandProduct Number: AR3100/902

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 40: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-28

Godkänd/Approved Dok nr/Doc no

AR3100/904-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3100_904_D

Specification of a GSM 1900 channel selective repeater4-channel version, High bandProduct Number: AR3100/904

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 155 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 41: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3131/006-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3131_006_D

Specification of a GSM 1900 channel selective repeater6-channel version, Lower bandProduct Number: AR3131/006

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 6 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard High Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 42: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3131/008-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3131_008_D

Specification of a GSM 1900 channel selective repeater8-channel version, Lower bandProduct Number: AR3131/008

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 8 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female

Page 43: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3131/906-201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3131_906_D

Specification of a GSM 1900 channel selective repeater6-channel version, Higher bandProduct Number: AR3131/906

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 6 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 230 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 44: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3131/908201

Rev

DSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3131_908_D

Specification of a GSM 1900 channel selective repeater8-channel version, Higher bandProduct Number: AR3131/908

1. Electrical specification (typical values)

The repeater complies with the FCC requirements

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 6 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 305 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard High Weight 75 lbs 37 Kg RF connectors N-type female Lock type ABLOY

Page 45: Repeater Specs

Standard 1900 MHz CDMA

Product Description AR3500_001 2 Channel, Low Band AR3500_901 2 Channel, High Band AR3530_001 2 Channel, Low Band, High Power AR3530_051 2 Channel, Low Band, High Power, MRX AR3530_901 2 Channel, High Band, High Power AR3530_951 2 Channel, High Band, High Power, MRX AR3535_022 4 Channel, Low Band, 2+2 AR3535_922 4 Channel, High Band, 2+2 AR3400_011 Band selective, Low band AR3400_911 Band selective, High band

Page 46: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-22Godkänd/Approved Dok nr/Doc no

AR3500/001-201Rev

GSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR3500_001_G

Specification of a CDMA 1900 channel selective repeater2-channel version, Lower band

Product number: AR3500/001

1. Electrical specification (typical values)The repeater complies with FCC requirements Frequency band Reverse link 1850 -1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +27 dBm/carrier Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

2. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 47: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-22Godkänd/Approved Dok nr/Doc no

AR3500/901-201Rev

GSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR3500_901_G

Specification of a CDMA 1900 channel selective repeater2-channel version, Upper band

Product number: AR3500/901

1. Electrical specification (typical value)The repeater complies with FCC requirements Frequency band Reverse link 1870 –1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +27 dBm/carrier Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 48: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3530/001-201

Rev

DSida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3530_001_D

Specification of a CDMA 1900 channel selective repeater2-channel version, Lower band

High PowerProduct Number: AR3530/001

1. Electrical specification (typical value)

The repeater complies with FCC requirements

Frequency band Reverse link 1850 –1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 49: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3530/051-201

Rev

BSida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3530_051_B

Specification of a CDMA 1900 channel selective repeater2-channel version, Lower band

High Power, MRXProduct Number: AR3530/051

1. Electrical specification (typical values)

The repeater complies with the requirements to FCC

Frequency band Reverse link 1850 –1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Band pass ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female

Page 50: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3530/901-201

Rev

DSida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3530_901_D

Specification of a CDMA 1900 channel selective repeater2-channel version, Upper band

High PowerProduct Number: AR3530/901

1. Electrical specification (typical values)

The repeater complies with the requirements to FCC

Frequency band Reverse link 1870 –1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female

Page 51: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2000-12-27

Godkänd/Approved Dok nr/Doc no

AR3530/951-201

Rev

BSida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3530_951_B

Specification of a CDMA 1900 channel selective repeater2-channel version, Upper band

High Power, MRXProduct Number: AR3530/951

1. Electrical specification (typical values)

The repeater complies with the requirements to FCC

Frequency band Reverse link 1870 –1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 52: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-04-17

Godkänd/Approved Dok nr/Doc no

AR3535/022-201

Rev

CSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3535_022_C

Specification of a CDMA 1900 channel selective repeater4-channel version, Lower bandProduct Number: AR3535/022

� True 2+2 CDMA channels in one package� The antenna connections 2+2 channels can either be combined (3dB loss) or separated

1. Electrical specification (typical values)

The repeater complies with the requirements to FCC

Frequency band Reverse link 1850 -1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, two carrier (no combiner) +33 dBm Output power RMS, four carrier (no combiner) +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 53: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-04-17

Godkänd/Approved Dok nr/Doc no

AR3535/922-201

Rev

CSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR3535_922_C

Specification of a CDMA 1900 channel selective repeater4-channel version, Upper bandProduct Number: AR3535/922

� True 2+2 CDMA channels in one package� The antenna connections 2+2 channels can either be combined (3dB loss) or separated

1. Electrical specification (typical values)

The repeater complies with the requirements to FCC

Frequency band Reverse link 1870 -1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, two carrier (no combiner) +33 dBm Output power RMS, four carrier (no combiner) +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB

Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 54: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-02-16 Godkänd/Approved

Dok nr/Doc no

AR3400/011-201 Rev

A Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3400_011_A.doc

Specification of a band selective repeater CDMA 1900 MHz version, Lower band

Product number: AR3400/011 1. Electrical specification (typical value) The repeater complies with the FCC requirements

Frequency band Reverse link 1850 – 1890 MHz Frequency band Forward link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Passband ripple 5 dB Output power RMS, one carrier + 33 dBm Output power RMS, two carrier + 28 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 4 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 55: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-02-16 Godkänd/Approved

Dok nr/Doc no

AR3400/901-201 Rev

A Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3400_911_A.doc

Specification of a band selective repeater

CDMA 1900 MHz version, Upper band Product number: AR3400/911

1. Electrical specification (typical values) The repeater complies with FCC requirements

Frequency band Reverse link 1870 – 1910 MHz Frequency band Forward link 1950 - 1990 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Output power RMS, one carrier + 33 dBm Output power RMS, two carrier + 28 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 4 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 VAC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 56: Repeater Specs

Compact 800 MHz Band Selective

Product Description

ALR4200_001 Adjustable 15 MHz BWALR4200_002 Adjustable 25 MHz BWALR4600_001 iDEN

Page 57: Repeater Specs

Compact 900 MHz Band Selective

Product Description

ALR1200_001 Adjustable 15 MHz BWALR1200_002 Adjustable 25 MHz BWALR1200_901 EGSM, Adj. 15 MHz BW

Page 58: Repeater Specs

Compact 1800 MHz Band Selective

Product Description

ALR2200_001 Adjustable BW, Low BandALR2200_901 Adjustable BW, High Band

Page 59: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2200/001-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2200-001_E

COMPACT repeater with adjustable bandwidth1800 MHz version, Low band

Product Number: ALR2200/001

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300 609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55°C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF connectors N-type female Lock type Allgon Safety bolts

Page 60: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2200/901-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2200-901_E

COMPACT repeater with adjustable bandwidth1800 MHz version, High bandProduct Number ALR2200/901

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 61: Repeater Specs

Compact 1900 MHz Band Selective

Product Description

ALR3200_001 Low BandALR3200_901 High Band

Page 62: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3200/001-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3200-001_E

COMPACT repeater with adjustable bandwidth1900 MHz version, Low band

Product Number: ALR3200/0011. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 63: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3200/901-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3200-901_E

COMPACT repeater with adjustable bandwidth1900 MHz version, High band

Product Number: ALR3200/901

1. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 64: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR4200/001-201

Rev

F

Sida/Page

Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

ALR4200-001_F

COMPACT repeater with adjustable bandwidth800 MHz version, 15 MHz BW

Product Number: ALR4200/0011. Electrical specification (typical value)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 29 dBm Output power, 2 carrier + 23 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 65: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR4200/002-201

Rev

D

Sida/Page

Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

ALR4200-002_D

COMPACT repeater with adjustable bandwidth800 MHz version, 25 MHz BW

Product Number: ALR4200/0021. Electrical specification (typical value)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 29 dBm Output power, 2 carrier + 23 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 66: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR4600/001-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR4600-001_E

COMPACT repeater with adjustable bandwidth800 MHz version, iDEN/SMR, 15 MHz BW

Product Number: ALR4600/0011. Electrical specification (typical value)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 806 – 825 MHz Frequency tuning band Down link 851 – 870 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 30 dBm Output power, 2 carrier + 24 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 67: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1200/001-201

Rev

F

Sida/Page

Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

ALR1200-001_F

COMPACT repeater with adjustable bandwidth900 MHz version, 15 MHz BW

Product Number: ALR1200/0011. Electrical specification (typical values)

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 68: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1200/002-201

Rev

C

Sida/Page

Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

ALR1200-002_C

COMPACT repeater with adjustable bandwidth900 MHz version, 25 MHz BW

Product Number: ALR1200/002

1. Electrical specification (typical values)

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 69: Repeater Specs
Page 70: Repeater Specs
Page 71: Repeater Specs
Page 72: Repeater Specs
Page 73: Repeater Specs

Page: 1 (2)

File: Options & FeaturesDate: 2000-12-19

Repeater Options and Features

1. OperationSet-up and commissioning of the repeater via an OMT (Operation & MaintenanceTerminal) software- Standard computer locally connected via RS232 or RCC- Standard computer remotely connected via modem (optional RCU-kit in the

repeater is then required)

2. Hardware & Software requirementsThe enclosed OMT software package requires at least:- 8 MB of RAM (16 is recommended)- 4 MB free hard disk space- Windows 95, 98, NT version 4.0 or higher

3. AlarmsInternal and external alarms locally or remotely monitored- LED sum alarm presentation on repeater front- Large number of internal alarms test points, each having a fixed alarm level- Four alarm ports for external alarm connections (e.g. intruder, fire, temperature

etc), each having flexible alarm level settingsSettable alarm levels:� None and ceasing� Warning� Error� Critical

Page 74: Repeater Specs

Page: 2 (2)

File: Options & FeaturesDate: 2000-12-19

4. Options and facilities� Dual band. Most repeaters can be dual band configured.� R2R (Repeater to Repeater) multidrop link is an advanced feature enabling data

communication between repeaters over one single remote interface (RCU)� Fiber optic kit. The repeater can easily be upgraded to a Fiber Optic Repeater by

adding a Fiber Optic Unit (FOU) or a Fiber Optic Node (FON).� Remote Control. All repeaters can be remote controlled either over a fixed wire-

line modem or a radio modem� Battery Back-Up (BBU) for either 25 or 50 Ah battery capacity� Door-switch to be connected to external alarm input� Operation and Maintenance System (OMS).� Power Supply. Most repeaters can be equipped with following power suppliers:

� 230 VAC� 115 VAC� +24 VDC� +48 VDC

A Windows NT based system for managing multiple repeaters in a network- Single or Multiuser as options- Polling of repeater- Status interrogation- Remote configuration- Supervision of ongoing configurations of multiple repeaters- Automatic downloading of new software- Scheduling activities- Report generating- External connections over the most common IP protocols (TCP/IP, UDP,

Streamsocket)- High level of inbuilt security classes

Page 75: Repeater Specs

Page: 1 (3) File: BUC2002005_RevB.doc Date: 2002-01-23

Allgon Repeater Conformity

1. General The repeater program covers all major cellular standards (GSM, AMPS/TDMA, CDMA and WCDMA). The products are formed from generic design platforms with a high grade of modularity. Mechanical housing and all essential RF electronics for the function of a repeater are standardised. Components like duplex filters and RF SAW filters are frequency specific and adopted to the different cellular standards. These few components are classified as strategic ones and are carefully selected. 2.Declaration of conformity Environmental Allgon repeater products are designed in accordance with ETS300 019: Stationary use at non-weather protected locations, extended climatic tests. Repeater Institute Concerns ETS

Reference Institute reference

AR types SEMKO • Encapsulation test acc. to IP65 requirements

EN 60 529 9749086-03

AR types Packforsk • Humidity • Chock • Vibration

ETS 300 019-2-4, class T4.1E

7861

ALR types SEMKO • Encapsulation test acc. to IP65 requirements

EN 60 529 0012029-04

ALR types SEMKO • Encapsulation UL50/CAN/CSA/CSA-C22.2 No 94 NEMA Type 4

0012029-05

ALR types Packforsk • Humidity • Chock • Vibration

ETS 300 019-2-5, class T4.1E

C01686 (prel.)

Page 76: Repeater Specs

Page: 2 (3) File: BUC2002005_RevB.doc Date: 2002-01-23

Radio Transmission and reception Allgon repeaters are designed in accordance with ETS300 577, GSM05.05: Radio transmission and reception (GSM05.05) and ETS300 609-4, part 4. Europe - Radio Transmission and Reception ETS 300 609-4 (harmonized standard ETS301 502) - EMC emission and immunity ETS 300 342-3 (Harmonized standard ETS 301 489-7) Allgon Products Accredited Laboratory reference AR1100/004 CS, 230 V, GSM AR1100/004 CS, 230 V, GSM AR1100/002 CS 24/48 VDC, GSM AR1112/104 COMB, 230 V, GSM AR1100/004 CS, 230 V, Opto, GSM AR2100/004 CS, 230 V, DCS, PCN AR1100/002 CS, 230 V, GSM AR1100/904 CS, 230 V, EGSM AR2200/901 CS, 230 V, DCS,PCN AR1100/804, CS,230 V, RGSM ALR2200/001, BS, 230 V, DCS, PCN ALR2200/901, BS, 230 V, DCS, PCN

1381/008/95 1381/002/96 1381/004/96 1381/009/96 1381/014/97 1381/015/97 1381/016/97 1381/047/97 D000063K, 983911D G127872H 0014109R 0014109R

US and Canada Relevant products fulfils the US emission requirements according to the Federal Communications Commission rule part 15, 22 and 90 and Industry of Canada specification RSS133 issue 1. Allgon Products FCC ref IC ref AR3100, CS, GSM 1900 AR3400, BS, DAMPS 1900 AR3500, SS, CDMA 1900 AR4200, BS, 800 MHz AR4200, BS, 800 MHz, New PA AR4500, SS, CDMA 800 MHz AR4540, SS, CDMA800 HP AR4600, BS, 800 MHz ALR4200, BS, 800 MHz, Compact ALR4600, BS, 800 MHz, iDEN, Compact

L6GAR3100 L6GAR3400 L6GAR3500 L6GAR4200 L6GAR4200A L6GAR4500 L6GAR4540 L6GAR4600 L6GALR4200 L6GALR4600

2869331142A 2869331138A 2869331135A 2869311169A 2869311209A 2869311191A 2869311237A 2869311189A 2869311227A 2869311226A

CS= Channel selective, BS= Band selective, SS= Segment selective, COMBI= Combinations of CS, BS and CS

Page 77: Repeater Specs

Page: 3 (3) File: BUC2002005_RevB.doc Date: 2002-01-23

Fibre Optic Transceiver The Fibre Optic Transceiver (FOT/FON) is to be regarded as a sub-assembly and is solely designed to fit Allgon repeater related products and consequently not allowed to be use in other kind of stand-alone applications. The FOT/FON is working with light in 1,3µm and 1,5µm wavelengths and can be integrated in any kind of Allgon repeater related products without effecting the radio performances. Safety The Allgon Fibre Optic Transceivers (FOT/FON) are classified as “CLASS 1 LASER PRODUCT” under the condition that they are integrated in any type of enclosure. Verification notice: - IEC/EN 60 825-1 Radiation safety of laser products for Europe and Canada - IEC/EN 60950 2:nd edition Safety of Information Technology Equipment, including Electrical Business Equipment. - US Food and Drug Administration requirements, part 1040.10, 1998 EMC The Allgon Fibre Optic Transceiver complies with EMC Directive 89/336/EEC and been tested in accordance with ETS300 342-3. Repeater safety - IEC Publication 65 - ETL recognition according to UL 1950 3:rd Edition and CAN/CSA C22.2 950-95: Repeater type Listing Mark

ETL AR31xx 2002761 AR34xx 2002761 AR35xx 2002761 AR42xx 2002761 AR45xx 2002761 AR46xx 2002761 ALR32xx 2002761 ALR42xx 2002761

Page 78: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2001-01-02Godkänd/Approved Dok nr/Doc no

SA102 54/1-201Rev

R1BSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

SA102 54-1-201_R1B

Operation and Maintenance SystemOMS version R1

Hardware and software requirements

The hardware requirements vary depending on if the computer will be used as a server machine or as a client.

Server:- Intel Pentium II based computer, running at a minimum of 450 MHz

- 256 MB RAM

- 2000 MB available disk space

- Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)

- Network card and TCP/IP protocol installed

- Windows NT4 with service pack 5 or higher

Client:- Intel Pentium based computer, running at a minimum of 266 MHz

- 64 MB RAM

- 600 MB available disk space

- Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)

- Network card and TCP/IP protocol installed

- Windows NT4 with service pack 6 or higher

- At least one serial communication port. (Multiport serial port board (DigiPortsâ or compatible) is stronglyrecommended.)

- Hayes compatible modems (minimum 9600 bps) for serial ports. See the Modem Init Strings section for furtherinformation about compatible modems.

- One telephone line or mobile phone for each modem. If callback will be used, then each telephone line musthave its own designated telephone number.

Page 79: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2001-01-02Godkänd/Approved Dok nr/Doc no

SA102 54/1-201Rev

R1BSida/Page

2Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

SA102 54-1-201_R1B

Function and Features

Multi-user System- Several users with separate security and configuration profiles can share the same database- Databases from Oracle Corporation with high level of security, performance and reliability

Multi-modem- Up to 128 modems can be used simultaneous

Alarm handling- Alarms are graphically displayed- Logged alarms can be sorted in any order

Multimedia Concept- User defined colour setting of alarm and activity levels- Alarm sound can be played

External Alarm transfer- SNMP- Nokia RPC- TCP/IP- ASCII

Traffic statistics- Querying traffic statistics for the last week- Report for 7 days displayed per hour or per 15 minutes periods- Graph presenting RSSI percentage value over a peak and mean average time scale- Export all information to a Microsoft Excel file- Storage time settable from 1 to 1000 days

Repeater activities- Directly executed- Scheduled executed any time or recurrent- Status shows all activities in progress and COM ports used

User and Client Management- Repeater Manager shows a map over a number of regions, cells and repeaters- User Manager contains all the user privileges- Workstation manager for OMS client organisation

Page 80: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2001-01-02Godkänd/Approved Dok nr/Doc no

SA102 54/1-201Rev

R1BSida/Page

3Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

SA102 54-1-201_R1B

Internal Mail System- Users in the OMS can communicate with each other- Individual or groups- Anyone to everyone event update

Channel plan import- MSI Planet version V2.7/2.8

Data Export- Enabling export of database to a number of databases

Templates- Efficient configurations- Template profile includes all repeater parameter settings

Reports- OMS database incl. repeater configuration, user preferences and logs- Printed out, displayed or saved

Help- On-line assistance- User’s Manual

Page 81: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2001-01-05Godkänd/Approved Dok nr/Doc no

K118-201Rev

R1BSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

K118-201_R1B

Specification of Allgon Fibre Optic TransceiverPart of FOU001

The specification is valid for:K118/1 Fibre Optic Transceiver, 1310 nm optical wavelengthK118/2 Fibre Optic Transceiver, 1550 nm optical wavelength

1. Electrical specification

Common Bandwidth @ 3 dB 1 800 - 2200 MHz Flatness 800 - 1000 MHz ± 2 dB Flatness 1700 - 2000 MHz ± 2 dB Input third order interception point > 50 dBm Input impedance 50 Ohm VSWR < 2 - Supply voltage + 7 V Power consumption, total < 3,5 W Transmitter RIN -155 dB/Hz Laser optic wavelength DFB 1310 or 1550 nm Max continuos RF input + 36 dBm Optical output power + 3 dBm Optic return loss > 55 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Receiver Optic wavelength 1250 – 1600 nm Max optic power input + 5 dBm RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Alarm threshold level, warning < - 12 dBm Alarm threshold level, error < - 15 dBm Optic return loss > 55 dB Noise power output at max gain, no fibre connected < -135 dBm/Hz

5. Mechanical specification Dimensions. (W x H x D) 230 x 25 x 115 mm Weight 0,66 Lbs 0,3 kg Optical fibre 9/125 Single mode RF connectors SMA Optical connectors FC-APC, DIN-APC Others available Software interface RS232 9 pin D-sub

1 The Fibre Optic Transceiver is connected to a duplexfilter thus limiting useful bandwidth to cellular standard in use.2 RF to RF system link gain is settable from –55 to –15 dB with 1 meter fibre jumper

Page 82: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell KnuutinenDattum/Date

2001-01-05Godkänd/Approved Dok nr/Doc no

K118-201Rev

R1BSida/Page

2Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

K118-201_R1B

4. Environmental specification Temperature range -4 to + 167 °F -20 to + 75 °C

5. OperationThe Fibre Optic Transceiver (FOT) is to be regarded as a modular component and is solely designed tofit Allgon repeaters and Base Station master Units and consequently not possible to use in other stand-alone applications. The FOT is a generic product for all types of Allgon repeaters.

6. Hardware & Software requirementsThe FOT is controlled by specific Fibre Optic Operation Terminal (FOOT) software requiring at least:- 486 desktop or notebook- Windows 95, 98 or NT version 4.0 or higher

7. AlarmsA summery alarm is generated by the FOT. The alarm connection is of an open collector type, open innormal mode and closed upon a failure.The summery alarm includes following individual alarms (accessible from FOOT software)- Laser failure (Tx)- No optic power received (Rx)- Temperature- Internal voltage

8. Declaration of conformity- Environmental specification ETS300 019-2-4- EMC emission and immunity ETS300 342-3- Electrical safety IEC/EN 60825-1

IEC/EN 60950

Page 83: Repeater Specs
Page 84: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-06-11 Godkänd/Approved

Dok nr/Doc no

K129/1_201 Rev

R1B Sida/Page

1 Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

K129-201_R1B.doc

Specification of Allgon Fibre Optic Node

Part of FOU Product Number: K129/1

The specification is valid for: K129/1 Fibre Optic Node, 1310 nm optical wavelength K129/2 Fibre Optic Node, 1550 nm optical wavelength 1. Electrical specification

Common Bandwidth @ 3 dB 1 800 - 2200 MHz Flatness 800 - 1000 MHz ± 2 dB Flatness 1700 - 2200 MHz ± 2 dB Input third order interception point > 50 dBm Input impedance 50 Ohm VSWR < 2 - Supply voltage + 7 V Power consumption, total < 5 W Transmitter RIN -155 dBc/Hz Laser optic wavelength DFB 1310 or 1550 nm Max continuos RF input + 36 dBm Min. optical output power, two levels + 3/0 dBm Optic return loss > 55 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Receiver Optic wavelength 1250 – 1600 nm Max optic power input + 5 dBm Low power output -15 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Alarm threshold level, settable warning 0 to - 40 dBm Alarm threshold level, settable error 0 to - 40 dBm Optic return loss > 55 dB Noise power output at max gain, no fibre connected < -135 dBm/Hz 5. Mechanical specification Dimensions. (W x H x D) 310x85x40 mm Weight 0,88 Lbs 0,4 kg

1 The Fibre Optic Node is connected to a duplexfilter thus limiting useful bandwidth to cellular standard in use. 2 RF to RF system link gain is settable from –60 to –20 dB with 1 meter fibre jumper

Page 85: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-06-11 Godkänd/Approved

Dok nr/Doc no

K129/1_201 Rev

R1B Sida/Page

2 Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

K129-201_R1B.doc

Optical fibre 9/125 Single mode RF connectors SMA Optical connectors FC-APC, DIN-APC Others available Software interface RS232 9 pin D-sub 4. Environmental specification Temperature range -4 to + 167 °F -20 to + 75 °C 5. Operation The Fibre Optic Node (FON) is to be regarded as a modular component and is solely designed to fit Allgon repeaters and Base Station master Units and consequently not possible to use in other stand-alone applications. The FON is a generic product for all types of Allgon repeaters. 5,5. New Features • Built-in input power meter (optic meter) • Optical output power, software controlled, two levels • IP addressing • Settable alarm thresholds (two levels) • Sub carrier for data communication • Battery Back-up with charger • External alarm inputs with settable levels and polarity • R2R interface • RCC support • Remote software download 6. Hardware & Software The FON is locally/remotely controlled by standard Allgon Operation & Maintenance Terminal Software (OMT) and Operation & Management System (OMS). 7. Alarms The FON supervision and alarm handling is built identical to our repeater products, e.g. fully compatible with OMT and OMS. Following alarms are given from FON: - Laser failure (Tx) - No optic power received (Rx) - Temperature - Internal voltage - Sub carrier link supervision - External alarm 8. Declaration of conformity - Environmental specification ETS300 019-2-4 - EMC emission and immunity ETS300 342-3 - Electrical safety IEC/EN 60825-1 IEC/EN 60950

Page 86: Repeater Specs

Standard 900 MHz EGSM Channel Selective

Product Description AR1100_902 2 Channel AR1100_904 4 Channel AR1111_908 8 Channel

Standard 900 MHz RGSM Channel Selective

Product Description AR1100_802 2 Channel AR1100_804 4 Channel

Page 87: Repeater Specs

Standard 900 MHz EGSM Band Selective

Product Description

AR1200_952 16,5 MHz BW

Page 88: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-03

Godkänd/Approved Dok nr/Doc no

AR1200/952-201

Rev

A

Sida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR1200_952_A

Specification of a EGSM Band selective Repeater900 MHz

Product Number: AR1200/952

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 880 - 915 MHz Frequency band Down link 925 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 89: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-03

Godkänd/Approved Dok nr/Doc no

AR1100/902-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR1100_902_A

Specification of a EGSM 900 channel selective repeater2-channel version

Product Number: AR1100/902

1. Electrical specification (typical values)

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 880 - 915 MHz Frequency band Down link 925 - 960 MHz Number of channels 2 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Page 90: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-08-23

Godkänd/Approved Dok nr/Doc no

AR1100/904-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR1100_904_A

Specification of a EGSM 900 channel selective repeater4-channel version

Product Number: AR1100/904

1. Electrical specification (typical values)

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 880 - 915 MHz Frequency band Down link 925 - 960 MHz Number of channels 4 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Page 91: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-02-06 Godkänd/Approved

Dok nr/Doc no

AR1100/908-201 Rev

A Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR1100_908_A.doc

Specification of a EGSM 900 channel selective repeater 8-channel version

Product Number: AR1100/908 1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 880 - 915 MHz Frequency band Down link 925 - 960 MHz Number of channels 8 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours 3.Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female

Page 92: Repeater Specs

Compact Dual Band

Product Description ALR1212_001 BS900/BS900 15 MHz BW ALR1212_002 BS900/BS900 25 MHz BW ALR1212_901 BS900/E-GSM 15 MHz BW ALR2212_001 BS1800/BS900 LB 15 MHz BW ALR2212_901 BS1800/BS900 UB 15 MHz BW ALR2222_001 BS1800/BS1800 LB 15 MHz BW ALR2222_095 BS1800/BS1800 LB/UB 15 MHz BW ALR2222_501 BS1800/BS1800 LB 25/15 MHz BW ALR2222_901 BS1800/BS1800 UB 15 MHz BW ALR3232_001 BS1900/BS1900 LB 15 MHz BW ALR3232_901 BS1900/BS1900 UB 15 MHz BW ALR3242_001 BS1900/BS800 LB 15 MHz BW ALR4242_002 BS800/BS800 15 MHz BW

Page 93: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-001_B

COMPACT repeater with adjustable bandwidth900/900 MHz version

Product Number: ALR1212/001

1. Electrical specification (typical values) GSM900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W

Page 94: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-001_B

2. Electrical specification (typical values) GSM900 Door

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

.

Page 95: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/002-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-002_B

COMPACT repeater with adjustable bandwidthBS900/BS900 25 MHz BW

Product Number: ALR1212/002

1. Electrical specification (typical values) GSM900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 890 – 915 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W

Page 96: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/002-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-002_B

2. Electrical specification (typical values) GSM900 Door

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 890 – 915 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 97: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/901-201

Rev

D

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-901_D

COMPACT repeater with adjustable bandwidth900 GSM/E-GSM

Product Number: ALR1212/901

1. Electrical specification (typical values) 900 GSM

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP > + 22 dBm Output power, 2 carrier + 16 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W

Page 98: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1212/901-201

Rev

D

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1212-901_D

2. Electrical specification (typical values) 900 E-GSM

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 880 – 905 MHz Frequency tuning band Down link 925 – 950 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 22 dBm Output power, 2 carrier + 16 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -13 to + 131 °F Temperature range -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159.5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 99: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2212/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2212-001_B

COMPACT repeater with adjustable bandwidth1800/900 MHz version, Low bandProduct Number: ALR2212/001

1. Electrical specification (typical values) 1800 MHz Low Band

The repeater complies with the requirement of ETS 300 609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55°C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

Page 100: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2212/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2212-001_B

2. Electrical specification (typical values) 900 MHz

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP > + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption 55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 101: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2212/901-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2212-901_B

COMPACT repeater with adjustable bandwidth1800/900 MHz version, High band

Product Number: ALR2212/901

1. Electrical specification (typical values) 1800 MHz High Band

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

Page 102: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2212/901-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2212-901_B

2. Electrical specification (typical values) 900 MHz

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP > + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption <55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 103: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-001_B

COMPACT repeater with adjustable bandwidth1800/1800 MHz version, Low band, Dual band

Product Number ALR2222/001

1. Electrical specification (typical values) GSM1800 Bottom

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC

Page 104: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-001_B

2. Electrical specification (typical values) GSM1800 Door

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact Low Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 105: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-08-19

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201

Rev

B

Sida/Page

Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

ALR2222-095_B.doc

COMPACT repeater with adjustable bandwidth

1800 MHz version, Low band/High band, Dual cell Product Number ALR2222/095

Band 1 (Low Band) 1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 20 dBm Output power, 2 carrier + 14 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC

Page 106: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-08-19

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201

Rev

B

Sida/Page

Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

ALR2222-095_B.doc

Band 2 (High Band) 2. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 20 dBm Output power, 2 carrier + 14 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts Note! -3 dB less output power according to combined antennas, 1 service and 1 donor antenna

Page 107: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/501-201

Rev

C

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-501_C

COMPACT repeater with adjustable bandwidth1800 MHz version, Low band/High band, Dual band

Product Number ALR2222/501

Band 1 (Low Band)

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC

Page 108: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/501-201

Rev

C

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-501_C

Band 2 (High Band)

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 109: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/901-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-901_B

COMPACT repeater with adjustable bandwidth1800 MHz version, High band, Dual band

Product Number ALR2222/901Band 1

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 - 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC

Page 110: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR2222/901-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR2222-901_B

Band 2

1. Electrical specification (typical values)

The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact Low Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 111: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3232/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3232-001_B

COMPACT repeater Dual band with adjustable bandwidth1900/1900 MHz version, Low band

Product Number: ALR3232/0011. Electrical specification (typical values) 1900 Bottom

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

Page 112: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3232/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3232-001_B

2. Electrical specification (typical values) 1900 Door

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 113: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3232/901-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3232-901_B

COMPACT repeater with adjustable bandwidth1900/1900 MHz version, High band

Product Number: ALR3232/901

1. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

Page 114: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3232/901-201

Rev

E

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3232-901_B

2. Electrical specification (typical values)

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 115: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3242/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3242-001_B

COMPACT repeater Dual band with adjustable bandwidth1900/800 MHz version, Low bandProduct Number: ALR3242/001

1. Electrical specification (typical values) 1900 Bottom

The repeater complies with the requirements of FCC

Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

Page 116: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR3242/001-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR3242-001_B

2. Electrical specification (typical values) 800 Door

The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 19 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 30 dBm Output power, 2 carrier + 24 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 117: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR4242/002-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR4242-002_B

COMPACT repeater with adjustable bandwidthDual 800 MHz version, 15 MHz BW

Product Number: ALR4242/002

1. Electrical specification (typical value) 800 Bottom

The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Band pass ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 – 265 VAC Power consumption <55 W

Page 118: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR4242/002-201

Rev

B

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR4242-002_B

2. Electrical specification (typical value) 800 Door

The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Band pass ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 – 265 VAC Power consumption <55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, -3 dB less output power

Page 119: Repeater Specs

Standard Dual Band

Product Description AR1212_052 GSM900 BS/BS 16,5 MHz BW AR2111_024 GSM1800 2 CH/900 4 CH LB AR2111_042 GSM1800 4 CH/900 2 CH LB AR2111_924 GSM1800 2 CH/900 4 CH UB AR2111_942 GSM1800 4 CH/900 2 CH UB AR2122_021 GSM1800 2 CH/BS1800 16,5 MHz BW AR2212_052 GSM1800 BS/900 BS LB AR2212_952 GSM1800 BS/900 BS UB AR3131_022 GSM1900 2+2 CH LB AR3131_044 GSM1900 4+4 CH LB AR3131_922 GSM1900 2+2 CH UB AR3442_052 TDMA1900 BS/BS 800 16,5 MHz BW AR3442_053 TDMA1900 BS/BS 800 25 MHz BW AR3542_052 CDMA1900/BS800 AR4242_052 BS800/BS800 16,5 MHz BW

Page 120: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR1212/052-201

Rev

A

Sida/Page

1Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR1212_052_A

Specification of a Dual Band selective Repeater900/900 MHz

Product Number: AR1212/052

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link Bottom 890 - 915 MHz Frequency band Up link Door 890 - 915 MHz Frequency band Down link Bottom 935 - 960 MHz Frequency band Down link Door 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power.

Page 121: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/024-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_024_A

Specification of a GSM 1800/900 channel selective repeater2+4 -channel version, Lower band

Product Number: AR2111/024

• The antenna connections 2+4 channels can either be combined diplexer or separated1. Electrical specification (typical values) GSM 1800 2 channels

The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

Page 122: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/024-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_024_A

2. Electrical specification (typical values) GSM 900 4 channels

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 4 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 123: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/042-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_042_A

Specification of a GSM 1800/900 channel selective repeater4+2 -channel version, Lower band

Product Number: AR2111/042

• The antenna connections 4+2 channels can either be combined with diplexer or separated

1. Electrical specification (typical values) GSM 1800 4 channels

The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 4 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55°C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

Page 124: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/042-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_042_A

2. Electrical specification (typical values) GSM 900 2 channels

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 2 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 125: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/924-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_924_A

Specification of a GSM 1800/900 channel selective repeater2+4 -channel version, High band

Product Number: AR2111/924

• The antenna connections 2+4 channels can either be combined diplexer or separated

1. Electrical specification (typical values) GSM 1800 2 channels

The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1730 - 1785 MHz Frequency band Down link 1825 - 1880 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

Page 126: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/924-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_924_A

2. Electrical specification (typical values) GSM 900 4 channels

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 4 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 127: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/942-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_942_A

Specification of a GSM 1800/900 channel selective repeater4+2 -channel version, High band

Product Number: AR2111/942

• The antenna connections 4+2 channels can either be combined with diplexer or separated

1. Electrical specification (typical values) GSM 1800 4 channels

The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1730 - 1785 MHz Frequency band Down link 1825 - 1880 MHz Number of channels 4 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55°C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W

Page 128: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2111/942-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2111_942_A

2. Electrical specification (typical values) GSM 900 2 channels

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 2 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 129: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR2122/021-201

Rev

A

Sida/Page

1Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2122_021_A

Specification of a Channel/Band selective RepeaterGSM1800 2 CH/BS1800 MHz, Lower band

Product Number: AR2122/021

1. Electrical specification (typical values) GSM 1800 2 CH

The repeater complies with the requirements of ETS 300609-4

Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W

Page 130: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR2122/021-201

Rev

A

Sida/Page

2Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2122_021_A

2. Electrical specification (typical values) GSM 1800 BSThe repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1710 – 1765 MHz Frequency band Down link 1805 - 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously

Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP + 29 dBm Output power 2 carrier + 23 dBm/carrier Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power

Page 131: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR2212/952/01_201

Rev

A

Sida/Page

1Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2212_952

Specification of a Band Selective Repeater Dual band1800 MHz/900 MHz High BandProduct Number: AR2212/952

1. Electrical specification (typical values) 1800 MHz High Band BottomThe repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1730 - 1785 MHz Frequency band Down link 1825 – 1880 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW3 dB, 16.5 MHz 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W

Page 132: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR2212/952/01_201

Rev

A

Sida/Page

2Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2212_952

2. Electrical specification (typical values) 900 MHz DoorThe repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W

3. Environmental specification

Temperature range -13 to +131 °F -25 to + 55 °C Casing class IP65 MTBF 50000 Hours

4. Mechanical specification

Dimensions. (W x H x D) 174 x 209 x 94 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 133: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/022-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_022_A

Specification of a Dual GSM 1900 channel selective repeater2+2 -channel version, Lower band

Product Number: AR3131/022

1. Electrical specification (typical values) GSM1900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

Page 134: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/022-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_022_A

2. Electrical specification (typical values) GSM1900 Door

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4.Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power

Page 135: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/044-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_044_A

Specification of a Dual GSM 1900 channel selective repeater4+4-channel version, Lower band

Product Number: AR3131/044

1. Electrical specification (typical values) GSM1900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 155 W

Page 136: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/044-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_044_A

2. Electrical specification (typical values) GSM1900 Door

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 155 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4.Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power

Page 137: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/922-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_922_A

Specification of a Dual GSM 1900 channel selective repeater2+2-channel version, High bandProduct Number: AR3131/922

1. Electrical specification (typical values) GSM1900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

Page 138: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3131/922-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3131_922_A

2. Electrical specification (typical values) GSM1900 Door

The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in thepass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously

Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB

Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power

Page 139: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR3442/052-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3442_052_A

Specification of a band selective repeater1900/800 MHz version, Lower band

Product number: AR3442/052

1. Electrical specification (typical value) BS1900

The repeater complies with the FCC requirements

Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Passband ripple 5 dB Max output power PEP ① + 36 dBm Output power 2 carrier ① + 30 dBm Automat gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

Page 140: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-16

Godkänd/Approved Dok nr/Doc no

AR3442/052-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3442_052_A

2. Electrical specification (typical value) BS800The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP ① +36 dBm Output power 2 carrier ① +30 dBm/carrier Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors 7/16-type Lock type ABLOY

Remark ①: If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 141: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-04-30

Godkänd/Approved Dok nr/Doc no

AR3442/053-201

Rev

ASida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3442_053_A

Specification of a band selective repeater1900/800 MHz version, Lower band

Product number: AR3442/053

1. Electrical specification (typical value) BS1900

The repeater complies with the FCC requirements

Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Passband ripple 5 dB Max output power PEP ① + 36 dBm Output power 2 carrier ① + 30 dBm Automat gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

Page 142: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-04-30

Godkänd/Approved Dok nr/Doc no

AR3442/053-201

Rev

ASida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3442_053_A

2. Electrical specification (typical value) BS800The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP ① +36 dBm Output power 2 carrier ① +30 dBm/carrier Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 MTBF 50000 Hours

4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors 7/16-type Lock type ABLOY

Remark ①: If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 143: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3542/052-201

Rev

A

Sida/Page

1

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3542_052_A

Specification of a Dual CDMA 1900/8002 CH/BS800, Lower band

Product number: AR3542/0521. Electrical specification (typical values) CDMA1900 Bottom

The repeater complies with FCC requirements

Frequency band Reverse link 1850 -1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +27 dBm/carrier Automatic gain control Implemented

Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB

Pass band ripple 3 dB

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

Page 144: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR3542/052-201

Rev

A

Sida/Page

2

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR3542_052_A

2. Electrical specification (typical value) BS800 DoorThe repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

3. Environmental specification

Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

4.Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 145: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR4242/052-201

Rev

A

Sida/Page

1Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4242_052_A

Specification of a Dual Band selective Repeater800/800 MHz

Product Number: AR4242/0521. Electrical specification (typical value) BS800 BottomThe repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

Page 146: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-18

Godkänd/Approved Dok nr/Doc no

AR4242/052-201

Rev

A

Sida/Page

2Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4242_052_A

2. Electrical specification (typical value) BS800 DoorThe repeater complies with the requirements of FCC

Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W

3. Environmental specification

Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 MTBF 50000 Hours

4. Mechanical specification

Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, -3 dB less output power.

Page 147: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2212/052/01_201

Rev

A

Sida/Page

1Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2212_052

Specification of a Band Selective Repeater Dual band1800 MHz/900 MHz Low BandProduct Number: AR2212/052

1. Electrical specification (typical values) 1800 MHz Low Band BottomThe repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 – 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW3 dB, 16.5 MHz 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W

Page 148: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-05-21

Godkänd/Approved Dok nr/Doc no

AR2212/052/01_201

Rev

A

Sida/Page

2Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR2212_052.doc

2. Electrical specification (typical values) 900 MHz DoorThe repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.5 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.5 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented

Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm

Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W

3. Environmental specification

Temperature range -13 to +131 °F -25 to + 55 °C Casing class IP65 MTBF 50000 Hours

4. Mechanical specification

Dimensions. (W x H x D) 174 x 209 x 94 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY If common donor and service antennas are used, diplexers are installed in the repeater. Approx. 1dB loss should be considered.

Page 149: Repeater Specs

Standard WCDMA

Product Description

AR6500_001 1-2 ChannelAR6560_001 1-2 Channel, High PowerAR6565_022 3-4 Channel

Page 150: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-08-20 Godkänd/Approved

Dok nr/Doc no

AR6500/001-201 Rev

H Sida/Page

1 Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

AR6500_001_H.doc

Specification of a WCDMA channel selective repeater 1-2 channel version

Product Number: AR6500/001 1. Electrical specification (typical values) The repeater complies with the requirements of 3G TS 25.106 V4.1.0

Frequency band Up link 1920 -1980 MHz Frequency band Down link 2110 - 2170 MHz Duplex spacing 190 MHz Number of channels 1-2 Nominal channel spacing 5 MHz Channel frequency steps 200 KHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 60-90 dB Absolute group delay <6 µs Output power (DL) RMS, one WCDMA carrier 1 +30 dBm Output power (DL) RMS, two WCDMA carrier 1 +25 dBm/carrier Output power (UL) RMS, one WCDMA carrier 1 +20 dBm Output power (UL) RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 2 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage 230 V AC Power consumption, max 140 W 1 Measured with test model 1/64 DPCH active channels 2 According to 3G TS 25.106 V4.1.0 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 151: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2002-08-20 Godkänd/Approved

Dok nr/Doc no

AR6560-201 Rev

H Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR6560_001_H.doc

Specification of a WCDMA channel selective repeater 1-2 channel version, high power

Product number: AR6560/001 1. Electrical specification (typical values) The repeater complies with the requirements of 3G TS 25.106 V4.1.0

Frequency band Up link 1920 –1980 MHz Frequency band Down link 2110 – 2170 MHz Duplex spacing 190 MHz Number of channels 1-2 Nominal channel spacing 5 MHz Channel frequency steps 200 KHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 65-95 dB Absolute group delay <6 µs Output power (DL) RMS, one WCDMA carrier 1 +38 dBm Output power (DL), RMS, two WCDMA carrier 1 +33 dBm/carrier Output power (UL), RMS, one WCDMA carrier 1 +20 dBm Output power (UL), RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 2 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss (typical) 14 dB RF-connectors N-type female Power supply voltage 230 V AC Power consumption, max 280 W 1 Measured with test model 1/64 DPCH active channels at 61% clipping ratio fulfilling spectrum emission mask 2 According to 3G TS 25.106 V4.1.0 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 152: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-10-29

Godkänd/Approved Dok nr/Doc no

AR6565/022-201

Rev

GSida/Page

1

Dok namn/Doc name

PRODUCT SPECIFICATION

Fil/file

AR6565_022_G

Specification of a WCDMA channel selective repeater2+2 channel version

Product Number: AR6565/022� True 2+2 CDMA channels in one package� The antenna connections 2+2 channels can either be combined (3dB loss) or separated1. Electrical specification (typical values)

The repeater complies with the requirements of 3G TS 25.106 V4.0.0

Frequency band Up link 1920 -1980 MHz Frequency band Down link 2110 - 2170 MHz Duplex spacing 190 MHz Number of channels 3-4 Nominal channel spacing 5 MHz Channel frequency steps 200 kHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 55-90 dB Absolute group delay <6 µs Output power ( DL) RMS, one WCDMA carrier 1 +30 dBm Output power ( DL) RMS, two WCDMA carrier 1 +25 dBm/carrier Output power ( UL) RMS, one WCDMA carrier 1 +20 dBm Output power ( UL) RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 4 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 4 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage (default) 230 V AC Power consumption, max 320 W1 Measured with test model 1/64 DPCH active channels2According to 3G TS 25.106 V4.0.0

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 MTBF 50000 Hours3. Mechanical specification Dimensions. (W x H x D) 17,4 x 20,9 x 9,4 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY

Page 153: Repeater Specs

ALLGON SYSTEMS ABUtfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-28Godkänd/Approved Dok nr/Doc no

AR1100/802-201Rev

BSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1100_802_B

Specification of a RGSM 900 channel selective repeater2-channel version

Product Number: AR1100/802

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 876 - 880 MHz Frequency band Down link 921 - 925 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Max output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ±100KHz > -3 dB Selectivity ±400KHz < -35 dB Selectivity ±600KHz < -45 dB Selectivity ±1 MHz < -50 dB Selectivity ±5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, typ. (max) 80 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 154: Repeater Specs

ALLGON SYSTEMS ABUtfärdare/Issued by

Kjell KnuutinenDattum/Date

2000-12-28Godkänd/Approved Dok nr/Doc no

AR1100/804-201Rev

BSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

AR1100_804_B

Specification of a RGSM 900 channel selective repeater4-channel version

Product Number: AR1100/804

1. Electrical specification (typical values)The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 876 - 880 MHz Frequency band Down link 921 - 925 MHz Number of channels 4 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segmentin the pass band

<± 200 ns

Max output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ±100KHz > -3 dB Selectivity ±400KHz < -35 dB Selectivity ±600KHz < -45 dB Selectivity ±1 MHz < -50 dB Selectivity ±5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, typ. (max) 120 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 MTBF 50000 Hours

2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Lock type ABLOY

Page 155: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-12-11

Godkänd/Approved Dok nr/Doc no

ALR1200/901-201

Rev

C

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ALR1200-901_C

COMPACT repeater with adjustable bandwidth900 MHz version, EGSM, 15 MHz BW

Product Number: ALR1200/901

1. Electrical specification (typical values)

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 880 – 900 MHz Frequency tuning band Down link 925 – 945 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F Temperature range -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

Page 156: Repeater Specs

LinDAS unit specification

Product Description

UA117 01/1 OCM, Opto Coverter ModuleUA119 01/1 RCM, RF Combining Module

Page 157: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-01

Godkänd/Approved Dok nr/Doc no

UA117 01/1-201

Rev

A

Sida/Page

1 (2)

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

OCM_UA117 01-1_A

Optical Converter Module OCMBase specification for UA117 01/1

The Opto Converter Module OCM is an active module used in Allgon standardized LinDAS (LightIndoor Distributed Antenna System to convert/reconvert RF/opto signals to/from the Central Huband the Remote Hub.

Typical valuesBand width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmMax RF input power +36 dBmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order IPin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 CºWeather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

FeaturesOperation capability

- Inbuilt input power meter (optic meter)- Optical output power, software controlled, two levels- IP addressing for supporting large system build out- Settable alarm thresholds (two levels)- Sub carrier for data communication over fiber, only one remote access point- Battery Back-up with charger- External alarm inputs with settable levels and polarity- R2R interface for communication between Allgon HW products via RS485- RCC support- Remote software download- Compatible with OMT and OMS software

Page 158: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-01

Godkänd/Approved Dok nr/Doc no

UA117 01/1-201

Rev

A

Sida/Page

2 (2)

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

OCM_UA117 01-1_A

Alarm capability- No optic power received (Rx)- Laser failure (Tx)- Temperature- Internal voltage- Sub carrier link supervision- External alarm

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Radiation Safety of laser products IEC/EN 60 825-1- Safety of IT technology IEC/EN 609 50- US Food and Drug Administration req. Part 1040.10, 1998- Electrical safety IEC publication 65- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95

Page 159: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-01

Godkänd/Approved Dok nr/Doc no

UA116 01/1-201

Rev

A

Sida/Page

1 (2)

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RCM_UA116 01-1_A

RF Combining Module RCMBase specification for UA116 01/1

The RF Combiner Module is to be used in the Allgon standardised indoor system LinDAS (LightIndoor Distributed Antenna System).

Typical valuesRF in/out from BTS Max +40 dBm RMS/port Note 1

RF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 CºWeather protection IP42RF connectors BTSIN/OUT

N-type female (Max 24)

RF connectors IN/OUT(to OCM)

SMA-type female (Max 6)

FeaturesThe RCM has a modular design allowing:- single and multiband configurations- single and multi operator capability- Easy up gradable

The RCM is designed in such way that electrical and mechanical data are fullycompatible to Allgon approved sub components like:- Hybrid couplers in frequency range 800-2300 MHz- Duplex filters 800, 900, 1800, 1900 and 2100 MHz frequency bands- Diplex filters for combining 800/1900, 900/1800, 900/2100, 1800/2100 MHz

Diplex/Duplex filters are supposed to work in the frequency bands with respect tostandard duplex spacing like GSM (900/1800/1900), PCS, AMPS/TDMA/iDEN andUMTS

Note 1 Max power handling capability of hybrid input connector. The input power and number of installedhybrid couplers must be in such way that the temperature of the RCM never will exceed 100 C°. Forced aircooling is always to recommend.

Page 160: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-01

Godkänd/Approved Dok nr/Doc no

UA116 01/1-201

Rev

A

Sida/Page

2 (2)

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RCM_UA116 01-1_A

Page 161: Repeater Specs

LinDAS system specification

System

Single band 900 MHzSingle band 1800 MHzDual band 800/1900 MHzDual band 900/1800 MHz

Page 162: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

LiNDAS System SpecificationSingle band 900 MHz

Electrical specification (typical values)

System Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 25 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB

Spur free dynamic range @ 200kHz >70 dB

Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + OCM <70 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier 9002 +194 +14

RF Combining Module (RCM)

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.

Page 163: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 CºWeather protection IP42RF connectors BTSIN/OUT

N-type female (Max 24)

RF connectors IN/OUT(to OCM)

SMA-type female (Max 6)

Page 164: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF / Opto Converter Module (OCM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order Ipin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 CºWeather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Page 165: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 + 25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)

System Features• Inbuilt input power meter (optic meter)• Optical output power, software controlled, two levels• IP addressing over Fiber To Fiber link (F2F)• Settable alarm thresholds (two levels)• Sub carrier for data communication over fiber• Battery Back-up with charger• External alarm inputs with settable levels and polarity• R2R interface• RCC support• Remote software download• Compatible with OMT and OMS software

5. Alarms• Laser failure (Tx)• No optic power received (Rx)• Temperature• Internal voltage• Sub carrier link supervision• External alarm

Note 1 In dual band applications calculate approx. 1 dB loss caused by the inbuilt diplex filters.

Page 166: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ManagementOMT (Operation & Maintenance Terminal) software for local and remote access mainly for installationand commissioning;• PC connected via RS232• PC connected via modem in CM

OMS (Operation & Maintenance System) software for fleet management• T1 connected via modem in CM

Software requirements OMTThe OMT software package requires at least:� Windows 95, 98 or NT version 4.0 or higher� 8 MB of RAM (16 is recommended)� 4 MB free hard disk space

Software requirements OMS� Intel Pentium II based computer, running at a minimum of 450 MHz� 256 MB RAM� 2000 MB available disk space� Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)� Network card and TCP/IP protocol installed� Windows NT4 with service pack 5 or higher

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Electrical safety IEC publication 65- Laser safety US Food and Drug Administration req.

Part 1040.10, 1998- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95- FCC 24E

Page 167: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

LiNDAS System SpecificationSingle band 1800 MHz

Electrical specification (typical values)

System Frequency tuning band Up link 2 1710 – 1785 MHz Frequency tuning band Down link 2 1805 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 26 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB

Spur free dynamic range @ 200kHz >70 dB

Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + OCM <70 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier 18002 +204 +15

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.2 Upper and lower band is available

Page 168: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF Combining Module (RCM)

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 CºWeather protection IP42RF connectors BTSIN/OUT

N-type female (Max 24)

RF connectors IN/OUT(to OCM)

SMA-type female (Max 6)

Page 169: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF / Opto Converter Module (OCM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order Ipin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 CºWeather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Page 170: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 + 25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)

System Features• Inbuilt input power meter (optic meter)• Optical output power, software controlled, two levels• IP addressing over Fiber To Fiber link (F2F)• Settable alarm thresholds (two levels)• Sub carrier for data communication over fiber• Battery Back-up with charger• External alarm inputs with settable levels and polarity• R2R interface• RCC support• Remote software download• Compatible with OMT and OMS software

5. Alarms• Laser failure (Tx)• No optic power received (Rx)• Temperature• Internal voltage• Sub carrier link supervision• External alarm

Note 1 In dual band applications calculate approx. 1 dB loss caused by the inbuilt diplex filters.

Page 171: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ManagementOMT (Operation & Maintenance Terminal) software for local and remote access mainly for installationand commissioning;• PC connected via RS232• PC connected via modem in CM

OMS (Operation & Maintenance System) software for fleet management• T1 connected via modem in CM

Software requirements OMTThe OMT software package requires at least:� Windows 95, 98 or NT version 4.0 or higher� 8 MB of RAM (16 is recommended)� 4 MB free hard disk space

Software requirements OMS� Intel Pentium II based computer, running at a minimum of 450 MHz� 256 MB RAM� 2000 MB available disk space� Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)� Network card and TCP/IP protocol installed� Windows NT4 with service pack 5 or higher

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Electrical safety IEC publication 65- Laser safety US Food and Drug Administration req.

Part 1040.10, 1998- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95- FCC 24E

Page 172: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

LiNDAS System SpecificationDual band 900/1800MHz

Electrical specification (typical values)

System Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Frequency tuning band Up link 2 1710 – 1785 MHz Frequency tuning band Down link 2 1805 - 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 25 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB

Spur free dynamic range @ 200kHz >70 dB

Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + OCM <150 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier 900 18002 +19 +204 +14 +15

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.2 Upper and lower band is available

Page 173: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF Combining Module (RCM)

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 CºWeather protection IP42RF connectors BTSIN/OUT

N-type female (Max 24)

RF connectors IN/OUT(to OCM)

SMA-type female (Max 6)

Page 174: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF / Opto Converter Module (OCM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order IPin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 CºWeather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Page 175: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 +25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)

System Features• Inbuilt input power meter (optic meter)• Optical output power, software controlled, two levels• IP addressing over Fiber To Fiber link (F2F)• Settable alarm thresholds (two levels)• Sub carrier for data communication over fiber• Battery Back-up with charger• External alarm inputs with settable levels and polarity• R2R interface• RCC support• Remote software download• Compatible with OMT and OMS software

5. Alarms• Laser failure (Tx)• No optic power received (Rx)• Temperature• Internal voltage• Sub carrier link supervision• External alarm

Note 1 In dual band applications calculate approx. 1 dB loss caused by the inbuilt diplex filters.

Page 176: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2001-11-27

Godkänd/Approved Dok nr/Doc no

RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

ManagementOMT (Operation & Maintenance Terminal) software for local and remote access mainly for installationand commissioning;• PC connected via RS232• PC connected via modem in CM

OMS (Operation & Maintenance System) software for fleet management• T1 connected via modem in CM

Software requirements OMTThe OMT software package requires at least:� Windows 95, 98 or NT version 4.0 or higher� 8 MB of RAM (16 is recommended)� 4 MB free hard disk space

Software requirements OMS� Intel Pentium II based computer, running at a minimum of 450 MHz� 256 MB RAM� 2000 MB available disk space� Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)� Network card and TCP/IP protocol installed� Windows NT4 with service pack 5 or higher

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Electrical safety IEC publication 65- Laser safety US Food and Drug Administration req.

Part 1040.10, 1998- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95- FCC 24E

Page 177: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-01-26

Godkänd/Approved Dok nr/Doc no

RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

LiNDAS System SpecificationDual band 800/1900MHz

Electrical specification

System Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) Min + 28 dBm 3rd order intercept point + 49 dBm Group delay exclusive fibre 6 µs Typical Noise figure at max gain, 25° C (no inbuildpower split)

8 dB

Spur free dynamic range @ 200kHz >70 dB

Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + CM <70 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier CDMA TDMA GSM1 +22 +25 +252 +17 +22 +224 +12 +17 +17

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.

Page 178: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-01-26

Godkänd/Approved Dok nr/Doc no

RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF Combining Module (RCM)

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on

configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 C�Weather protection IP42RF connectors BTS IN/OUT N-type female (Max 6)RF connectors IN/OUT (to CM) SMA-type female (Max 24)

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on

configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 C�Weather protection IP42RF connectors BTS IN/OUT N-type female (Max 6)RF connectors IN/OUT (to CM) SMA-type female (Max 24)

Page 179: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-01-26

Godkänd/Approved Dok nr/Doc no

RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

RF / Opto Converter Module (CM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmRF transmitter/receiver attenuation settableby SW in 1 dB steps

0 – 20 dB

Receiver settable alarm level WARNING 0 to -40 dBReceiver settable alarm level ERROR 0 to -40 dBmSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 C�Weather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmRF transmitter/receiver attenuation settableby SW in 1 dB steps

0 – 20 dB

Receiver settable alarm level WARNING 0 to -40 dBReceiver settable alarm level ERROR 0 to -40 dBmSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 C�Weather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Page 180: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-01-26

Godkänd/Approved Dok nr/Doc no

RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

Remote Hub (RH)

System Features� Inbuilt input power meter (optic meter)� Optical output power, software controlled, two levels� IP addressing over Fiber To Fiber link (F2F)� Settable alarm thresholds (two levels)� Sub carrier for data communication� Battery Back-up with charger� External alarm inputs with settable levels and polarity� R2R interface� RCC support� Remote software download� Compatible with OMT and OMS software

5. Alarms� Laser failure (Tx)� No optic power received (Rx)� Temperature� Internal voltage� Sub carrier link supervision� External alarm

Max composit output power (IM –13 dBm) + 29 dBmMax composit output power (IM –30 dBm) + 26 dBmMax composit output power (IM –36 dBm) + 25 dBmMax composit output power @ 4 antenna ports Above – 6 dB/portMax absolute group delay 6 µsNoise figure @ 25 C� 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption 55 WDimension (WxHxD) in mm 385x385x100Weight 8 kgTemp range 0 to +50 C�Weather protection IP42RF connectors N-type female (max 4)

Max composit output power (IM –13 dBm) + 29 dBmMax composit output power (IM –30 dBm) + 26 dBmMax composit output power (IM –36 dBm) + 25 dBmMax composit output power @ 4 antenna ports Above – 6 dB/portMax absolute group delay 6 µsNoise figure @ 25 C� 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption 55 WDimension (WxHxD) in mm 385x385x100Weight 8 kgTemp range 0 to +50 C�Weather protection IP42RF connectors N-type female (max 4)

Page 181: Repeater Specs

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen

Dattum/Date

2002-01-26

Godkänd/Approved Dok nr/Doc no

RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

OperationSet-up and control of the system via OMT (Operation & Maintenance Terminal) software� PC connected via RS232� PC connected via modem in CM� Set-up, monitoring and control of the system via OMS (Operation & Maintenance System) software� PC connected via modem in CM

Software requirements OMTThe OMT software package requires at least:� Windows 95, 98 or NT version 4.0 or higher� 8 MB of RAM (16 is recommended)� 4 MB free hard disk space

Software requirements OMS� Intel Pentium II based computer, running at a minimum of 450 MHz� 256 MB RAM� 2000 MB available disk space� Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)� Network card and TCP/IP protocol installed� Windows NT4 with service pack 5 or higher

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Electrical safety IEC publication 65- Laser safety US Food and Drug Administration req.

Part 1040.10, 1998- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95- FCC 24E

Page 182: Repeater Specs

Confidential InformationReleaste Repeater Products Volume Delivery time

A by forecast 5 daysFC = Forecast Class B by forecast 20 daysAll products has R-state C by forecast on request

Revision Date2002-04-16

Product nr. Information FC Prod. Grp.ABR5500/00101 Repeater DMB-1500 Mhz C 4735AR1100/00201 Repeater GSM900 2 ch 230VAC A 4705AR1100/00202 Repeater GSM900 2 ch 230VAC, RCU A 4705AR1100/00203 Repeater GSM900 2 ch 24VDC B 4705AR1100/00204 Repeater GSM900 2 ch 24VDC, RCU B 4705AR1100/00205 Repeater GSM900 2 ch 48 VDC B 4705AR1100/00206 Repeater GSM900 2 ch 48, RCU B 4705AR1100/00207 Repeater GSM900 2 ch 115VDC B 4705AR1100/00208 Repeater GSM900 2 ch 115VDC, RCU B 4705AR1100/00401 Repeater GSM900 4 ch 230VAC A 4705AR1100/00402 Repeater GSM900 4 ch 230VAC, RCU A 4705AR1100/00403 Repeater GSM900 4 ch 24VDC B 4705AR1100/00404 Repeater GSM900 4 ch 24VDC, RCU B 4705AR1100/00405 Repeater GSM900 4 ch 48 VDC B 4705AR1100/00406 Repeater GSM900 4 ch 48 VDC, RCU B 4705AR1100/00407 Repeater GSM900 4 ch 115VAC B 4705AR1100/00408 Repeater GSM900 4 ch 115VAC, RCU B 4705AR1100/80203 Repeater RGSM900 2 ch 24VDC C 4705AR1100/80204 Repeater RGSM900 2 ch 24VDC+RCU C 4705AR1100/80205 Repeater RGSM900 2 ch 48VDC C 4705AR1100/90202 Repeater EGSM 2 ch 230VAC, RCU B 4705AR1100/90204 Repeater EGSM 2 ch 24VDC, RCU. B 4705AR1100/90206 Repeater EGSM 2 ch 48VDC, RCU. B 4705AR1100/90401 Repeater EGSM 4 ch 230VAC. B 4705AR1100/90402 Repeater EGSM 4 ch 230VAC, RCU. B 4705AR1100/90404 Repeater EGSM 4 ch 24VDC, RCU B 4705AR1100/90406 Repeater EGSM 4 ch 48VDC, RCU B 4705AR1111/00601 Repeater GSM900 6 ch 230VAC A 4705AR1111/00602 Repeater GSM900 6 ch 230VAC, RCU A 4705AR1111/00603 Repeater GSM900 6 ch 24VDC B 4705AR1111/00604 Repeater GSM900 6 ch 24VDC, RCU B 4705AR1111/00605 Repeater GSM900 6 ch 48VDC B 4705AR1111/00606 Repeater GSM900 6 ch 48VDC, RCU B 4705AR1111/00801 Repeater GSM900 8 ch 230VAC B 4705AR1111/00802 Repeater GSM900 8 ch 230VAC, RCU B 4705AR1111/00803 Repeater GSM900 8 ch 24VDC C 4705AR1111/90601 Repeater EGSM 6 ch 230VAC B 4705

Page 183: Repeater Specs

AR1200/05201 Repeater, BS 16,5 MHz 230VAC B 4745AR1200/05202 Repeater, BS 16,5MHz 230VAC, RCU B 4745AR2100/00201 Repeater DCS-1800 2 ch.LB 230VAC B 4710AR2100/00202 Repeater DCS-1800 2 ch.LB 230VAC, RCU B 4710AR2100/00203 Repeater DCS-1800 2 ch.LB 24VDC B 4710AR2100/00204 Repeater DCS-1800 2 ch.LB 24VDC RCU B 4710AR2100/00207 Repeater DCS-1800 2 ch LB 115VAC B 4710AR2100/00208 Repeater DCS-1800 2 ch.LB 115VAC, RCU B 4710AR2100/00401 Repeater DCS-1800 4 ch.LB 230VAC B 4710AR2100/00402 Repeater DCS-1800 4 ch.LB 230VAC,RCU B 4710AR2100/00407 Repeater DCS-1800 4 ch.LB 115VAC B 4710AR2100/00408 Repeater DCS-1800 4 ch.LB 115VAC, RCU B 4710AR2100/90201 Repeater DCS-1800 2 ch.UB 230VAC B 4710AR2100/90202 Repeater DCS-1800 2 ch.UB 230VAC, RCU B 4710AR2100/90207 Repeater DCS-1800 2 ch UB 115VAC B 4710AR2100/90208 Repeater DCS-1800 2 ch UB 115VAC, RCU B 4710AR2100/90401 Repeater DCS-1800 4 ch.UB 230VAC B 4710AR2100/90402 Repeater DCS-1800 4 ch.UB 230VAC, RCU B 4710AR2200/00101 Repeater BS1800 LB adj 16,9 MHZ 230VAC B 4750AR2200/00102 Repeater BS1800 LB adj 16,9 MHz 230VAC, RCU B 4750AR2200/00107 Repeater BS1800 LB adj 16,9 MHz 115VAC B 4750AR2200/00108 Repeater BS1800 LB adj 16,9 MHz 115VAC, RCU B 4750AR2200/90101 Repeater BS1800 UB adj 16,9 MHz 230VAC B 4750AR2200/90102 Repeater BS1800 UB adj 16,9 MHz 230VAC, RCU B 4750AR3100/00201 Repeater GSM1900 2 ch.LB 115 VAC B 4715AR3100/00207 Repeater GSM1900 2 ch.LB 230VAC B 4715AR3100/00401 Repeater GSM1900 4 ch.LB 115VAC B 4715AR3100/90201 Repeater GSM1900 2 ch.UB 115VAC B 4715AR3100/90207 Repeater GSM1900 2 ch UB 230VAC B 4715AR3400/00101 Repeater BS 1900 LB, 115 V C 4755AR3500/00101 Repeater CDMA-1900 2 CH 115VAC LB C 4735AR3500/00103 Repeater CDMA-1900 2 CH 21-60VDC LB C 4735AR3500/00104 Repeater CDMA-1900 2 CH 21-60VDC, RCU LB C 4735AR3500/00107 Repeater CDMA-1900 2 CH 230VAC LB C 4735AR3500/90101 Repeater CDMA-1900 UB 2 CH 115VAC C 4735AR4200/05201 Repeater BS 800 16,9 230VAC B 4740AR4200/05207 Repeater BS-800 16,9 115VAC B 4740AR6500/00101 Repeater W-CDMA 1-2 Ch 230VAC B 4790AR6565/02201 Repeater W-CDMA 3-4 Ch 230VAC C 4790

Page 184: Repeater Specs

Confidential InformationNot Released Repeater Products, possible to order Volume Delivery time

A by forecast 5 daysFC = Forecast Class B by forecast 20 daysThese products are available and possible to order, but are in P-state C by forecast on requestdue to one or several subsystems or components not are in R-state.Revision Date2002-04-16

Product nr. Information FC Prod. Grp.ALR1200/00101 Compact 900 MHz, ABW 15 MHz B 4775ALR1200/00102 Compact 900 MHz, ABW 15 MHz, RCC B 4775ALR1200/00201 Compact 900 MHz, ABW 25 MHz B 4775ALR1200/00202 Compact 900 MHz, ABW 25 MHz, RCC B 4775ALR1200/00401 Compact 900 MHz, ABW 25 MHz, DC C 4775ALR1200/00402 Compact 900 MHz, ABW 25 MHz, DC, RCC C 4775ALR1212/00101 Compact Dual 900 15 MHz C 4760ALR1212/00102 Compact Dual 900 15 MHz, RCC C 4760ALR2200/00101 Compact BS-1800 LB 15 B 4780ALR2200/00102 Compact BS-1800 LB 15 RCC B 4780ALR2200/00201 Compact BS-1800 LB 25 MHz C 4780ALR2200/00202 Compact BS-1800 LB 25 MHz RCC C 4780ALR2200/90101 Compact BS-1800 UB 15 B 4780ALR2200/90102 Compact BS-1800 UB 15 RCC B 4780ALR2200/90201 Compact BS-1800 UB 25 MHz C 4780ALR2200/90202 Compact BS-1800 UB 25 MHz RCC C 4780ALR2212/00101 Compact BS Dual1800/900 LB C 4760ALR2212/00102 Compact Dual 1800/ 900 15 MHz, RCC C 4760ALR2212/90101 Compact.BS Dual 1800/900 UB C 4760ALR2212/90102 Compact.BS Dual 1800/900 UB, RCC C 4760ALR2222/00101 Compact BS Dual 1800 15 C 4760ALR2222/00102 Compact BS Dual 1800 15 RCC C 4760ALR2222/09501 Compact BS Dual 1800 15 LB, UB 1 service 1 donor C 4760ALR2222/09502 Compact BS Dual 1800 15 LB, UB 1 service 1 donor RCC C 4760ALR3200/00101 Compact BS1900 LB B 4785ALR3200/00102 Compact BS1900 LB, RCC B 4785ALR3200/90101 Compact BS1900 UB B 4785ALR3200/90102 Compact BS1900 UB, RCC B 4785ALR3232/00101 Compact Dual 1900 LB C 4760ALR3232/00102 Compact Dual 1900 LB, RCC C 4760ALR3232/09501 Compact Dual 1900 LB, UB 1 service 1 donor C 4760ALR3232/09502 Compact Dual 1900 LB, UB 1 service 1 donor RCC C 4760ALR3232/90101 Compact Dual 1900 UB C 4760ALR3232/90102 Compact Dual 1900 UB, RCC C 4760ALR3242/00101 Compact Dual 1900/800 LB C 4760ALR3242/00102 Compact Dual 1900/800 LB, RCC C 4760ALR3242/00301 Compact Dual 1900/800 LB, 1 service 2 donor C 4760

Page 185: Repeater Specs

ALR3242/00302 Compact Dual 1900/800 LB, 1 service 2 donor, RCC C 4760ALR3242/90202 Compact Dual 1900/800 UB, 25 MHz, RCC C 4760ALR3242/90301 Compact Dual 1900/800 UB, 1 service 2 donor C 4760ALR3242/90302 Compact Dual 1900/800 UB, 1 service 2 donor, RCC C 4760ALR3242/00501 Compact Dual 1900/800 LB, 1 service 1 donor C 4760ALR3242/00502 Compact Dual 1900/800 LB, 1 service 1 donor. RCC C 4760ALR3242/90501 Compact Dual 1900/800 UB, 1 service 1 donor C 4760ALR3242/90502 Compact Dual 1900/800 UB, 1 service 1 donor, RCC C 4760ALR4200/00101 Compact BS 800 15 MHz B 4770ALR4200/00201 Compact BS 800 25MHz B 4770ALR4242/00101 Compact Dual 800 15 C 4760ALR4242/00102 Compact Dual 800 15 RCC C 4760ALR4600/00101 Compact 800 SMR-IDEN B 4770AR1111/00804 Repeater GSM900 8 ch 24VDC, RCU B 4705AR1111/90602 Repeater EGSM 6 ch 230VAC, RCU B 4705AR1111/90606 Repeater EGSM 6 ch 48VDC, RCU B 4705AR1111/90801 Repeater EGSM 8 ch 230VAC B 4705AR1111/90802 Repeater EGSM 8 ch 230VAC, RCU B 4705AR1111/90806 Repeater EGSM 8 ch 48VDC, RCU B 4705AR1200/05203 Repeater, BS 16,5MHz 21-60VDC B 4745AR1200/05204 Repeater, BS 16,5MHz 21-60VDC, RCU B 4745AR1200/05301 Repeater, BS 25 MHz 230VAC B 4745AR1200/05302 Repeater, BS 25 MHz 230VAC, RCU B 4745AR1200/95201 Repeater, EGSM, BS 16,9 MHz 230VAC C 4745AR1200/95202 Repeater, EGSM, BS 16,9 MHz 230VAC, RCU C 4745AR1200/95203 Repeater, EGSM, BS 16,9 MHz 21-60VDC C 4745AR1200/95204 Repeater, EGSM, BS 16,9 MHz 21-60VDC, RCU C 4745AR1212/05201 Repeater, Dual BS 900. 16,9 MHz 230VAC C 4760AR1212/05202 Repeater, Dual BS 900. 16,9 MHz 230VAC, RCU C 4760AR1212/05203 Repeater, Dual BS 900. 16,9 MHz 21-60VDC C 4760AR1212/05204 Repeater, Dual BS 900. 16,9 MHz 21-60VDC, RCU C 4760AR2111/02201 Repeater Dual 1800/900 2+2 ch LB 230VAC C 4760AR2111/02401 Repeater Dual 1800/900 2+4 ch LB 230VAC C 4760AR2111/04401 Repeater Dual 1800/900 4+4 ch LB 230VAC B 4760AR2111/04402 Repeater Dual 1800/900 4+4 ch LB 230VAC RCU B 4760AR2121/00601 Repeater DCS-1800 6 ch LB 230VAC B 4710AR2121/00602 Repeater DCS-1800 6 ch LB 230VAC RCU B 4710AR2121/00606 Repeater DCS-1800 6 ch LB 48VDC RCU B 4710AR2121/00801 Repeater DCS-1800 8 ch LB 230VAC C 4710AR2121/90601 Repeater DCS-1800 6 ch UB 230VAC B 4710AR2121/90602 Repeater DCS-1800 6 ch UB 230VAC RCU C 4710AR2121/90801 Repeater DCS-1800 8 ch UB 230VAC B 4710AR2142/04201 Repeater Dual 1800 4 CH/800 BS 230VAC C 4710AR2142/04202 Repeater Dual 1800 4 CH/800 BS 230VAC RCU C 4710AR2142/04207 Repeater Dual 1800 4 CH/800 BS 115VAC C 4710AR2200/00103 Repeater BS1800 LB adj 16,9 MHz 21-60VDC B 4750AR2200/00104 Repeater BS1800 LB adj 16,9 MHz 21-60VDC, RCU B 4750AR2200/90103 Repeater BS1800 UB adj 16,9 MHz 21-60VDC B 4750

Page 186: Repeater Specs

AR2200/90104 Repeater BS1800 UB adj 16,9 MHz 21-60VDC, RCU B 4750AR2212/95201 Repeater Dual BS1800/BS900 UB 230VAC C 4760AR2212/95202 Rep. Dual BS1800/BS900 UB 230VAC, RCU C 4760AR2212/95203 Rep. Dual BS1800/BS900 UB 21-60VDC C 4760AR2212/95204 Rep. Dual BS1800/BS900 UB 21-60VDC, RCU C 4760AR2222/00207 Rep. Dual BS1800 LB 115VAC C 4760AR3100/00404 Repeater GSM1900 4 ch.LB 24VDC, RCU B 4715AR3100/00407 Repeater GSM1900 4 ch.LB 230VAC B 4715AR3100/00408 Repeater GSM1900 4 ch.LB 230VAC RCU C 4715AR3100/50201 Repeater GSM1900 2 ch FB, 115 V C 4715AR3100/50207 Repeater GSM1900 2 ch FB, 230 V C 4715AR3100/50401 Repeater GSM1900 4 ch FB 115VAC C 4715AR3100/50404 Repeater GSM1900 4 ch FB 24VDC RCU C 4715AR3100/50407 Repeater GSM1900 4 ch FB 230VAC C 4715AR3131/02201 Repeater Dual GSM1900 2+2 CH LB 115VAC C 4715AR3131/04401 Repeater Dual GSM1900 4+4 CH LB 115VAC C 4715AR3131/92201 Repeater Dual GSM1900 2+2 CH UB 115VAC C 4715AR3400/00103 Repeater BS 1900 LB, 21-60VDC C 4755AR3400/00104 Repeater BS 1900 LB, 21-60VDC, RCU C 4755AR3400/00107 Repeater BS 1900 LB, 230 V C 4755AR3400/01101 Repeater BS CDMA 1900 LB, 115 V B 4755AR3400/01102 Repeater BS CDMA 1900 LB, 115 V RCU B 4755AR3400/90101 Repeater BS 1900 UB 115VAC C 4755AR3400/90103 Repeater BS 1900 UB 21-60VDC C 4755AR3400/90104 Repeater BS 1900 UB 21-60VDC, RCU C 4755AR3400/90107 Repeater BS 1900 UB 230VAC C 4755AR3400/91101 Repeater BS CDMA 1900 UB, 115 V B 4755AR3400/91102 Repeater BS CDMA 1900 UB, 115 V RCU B 4755AR3434/00101 Repeater Dual BS 1900 TDMA LB 115VAC C 4715AR3434/51101 Repeater Dual CDMA 1900 BS, 16,5 MHz, LB, UB C 4735AR3434/51102 Repeater Dual CDMA 1900 BS, 16,5 MHz, LB, UB RCU C 4735AR3434/51103 Repeater Dual CDMA 1900 BS, 16,5 MHz, 21-60VDC LB, UB C 4735AR3434/51104 Repeater Dual CDMA 1900 BS, 16,5 MHz, 21-60 VDC LB, UB RCUC 4735AR3442/05201 Repeater Dual BS1900/800 LB 115VAC C 4715AR3442/05301 Repeater Dual BS1900/800 LB, 25 MHz 115VAC C 4715AR3442/05303 Repeater Dual BS1900/800 LB, 25 MHz 24VDC C 4715AR3500/05101 Repeater CDMA-1900 2 CH MRX 115VAC LB B 4735AR3500/05103 Repeater CDMA-1900 2 CH MRX 21-60VDC LB B 4735AR3500/05104 Repeater CDMA-1900 2 CH MRX 21-60VDC, RCU LB B 4735AR3500/05107 Repeater CDMA-1900 2 CH MRX 230VAC LB B 4735AR3500/90103 Repeater CDMA-1900 UB 2 CH 21-60VDC C 4735AR3500/90104 Repeater CDMA-1900 UB 2 CH 21-60VDC, RCU C 4735AR3500/90107 Repeater CDMA-1900 UB 2 CH 230VAC C 4735AR3500/95107 Repeater CDMA-1900 UB 2 CH MRX 230VAC C 4735AR3530/05101 Repeater CDMA-1900 MRX HP 2 CH 115VAC LB B 4735AR3530/05103 Repeater CDMA-1900 MRX HP 2 CH 21-60VDC LB B 4735AR3530/05104 Repeater CDMA-1900 MRX HP 2 CH 21-60VDC, RCU LB B 4735AR3530/05107 Repeater CDMA-1900 MRX HP 2 CH 230VAC LB C 4735

Page 187: Repeater Specs

AR3530/95101 Repeater CDMA-1900 MRX HP 2 CH 115VAC UB C 4735AR3530/95102 Repeater CDMA-1900 MRX HP 2 CH 115VAC UB RCU C 4735AR3530/95103 Repeater CDMA-1900 MRX HP 2 CH 24VDC UB C 4735AR3530/95104 Repeater CDMA-1900 MRX HP 2 CH 24VDC UB RCU C 4735AR3530/95107 Repeater CDMA-1900 MRX HP 2 CH 230VAC UB C 4735AR3535/95107 Repeater CDMA-1900 MRX 4 CH 230VAC UB C 4735AR3535/02201 Repeater CDMA-1900 2+2 CH 115VAC LB C 4735AR3535/02202 Repeater CDMA-1900 2+2 CH 115VAC, RCU LB C 4735AR3535/02203 Repeater CDMA-1900 2+2 CH 21-60VDC LB C 4735AR3535/02204 Repeater CDMA-1900 2+2 CH 21-60VDC, RCU LB C 4735AR3535/02207 Repeater CDMA-1900 2+2 CH 230VAC LB C 4735AR3535/92201 Repeater CDMA-1900 2+2 CH UB 115VAC C 4735AR3535/92202 Repeater CDMA-1900 2+2 CH UB 115VAC, RCU C 4735AR3535/92203 Repeater CDMA-1900 2+2 CH UB 21-60VDC C 4735AR3535/92204 Repeater CDMA-1900 2+2 CH UB 21-60VDC, RCU C 4735AR3535/92207 Repeater CDMA-1900 2+2 CH UB 230VAC C 4735AR3542/05201 Repeater Dual CDMA1900/BS800 115VAC LB C 4760AR3542/05203 Repeater Dual CDMA1900/BS800 21-60VDC LB C 4760AR3542/05204 Repeater Dual CDMA1900/BS800 21-60VDC, RCU LB C 4760AR4200/01201 Repeater BS CDMA 800, 25 MHz 230 V C 4740AR4200/01202 Repeater BS CDMA 800, 25 MHz 230 V RCU C 4740AR4200/01203 Repeater BS CDMA 800, 25 MHz 21-60VDC C 4740AR4200/01204 Repeater BS CDMA 800, 25 MHz 21-60VDC RCU C 4740AR4200/01207 Repeater BS CDMA 800, 25 MHz 115VAC C 4740AR4200/01208 Repeater BS CDMA 800, 25 MHz 115 VAC RCU C 4740AR4200/05203 Repeater BS 800 16,9 21-60VDC B 4740AR4200/05204 Repeater BS 800 16,9 21-60VDC, RCU B 4740AR4200/05301 Repeater BS 800 25 230VAC C 4740AR4200/05303 Repeater BS 800 25 21-60VDC C 4740AR4200/05304 Repeater BS 800 25 21-60VDC, RCU C 4740AR4200/05307 Repeater BS 800 25 115VAC C 4740AR4242/05201 Repeater Dual BS 800 16,9 230VAC C 4740AR4242/05203 Repeater Dual BS 800 16,9 21-60VDC C 4740AR4242/05204 Repeater Dual BS 800 16,9 21-60VDC, RCU C 4740AR4242/05207 Repeater Dual BS 800 16,9 115VAC C 4740AR4500/00141 Repeater CDMA-800 2 CH 230VAC C 4720AR4500/00142 Repeater CDMA-800 2 CH 230VAC, RCU C 4720AR4500/00147 Repeater CDMA-800 2 CH 115VAC C 4720AR4500/05141 Repeater CDMA-800 2 CH 230VAC, MRX A 4720AR4500/05142 Repeater CDMA-800 2 CH 230VAC, RCU, MRX A 4720AR4500/05147 Repeater CDMA-800 2 CH 115VAC, MRX B 4720AR4540/05141 Repeater CDMA-800 2 CH 230VAC, MRX HP A 4720AR4540/05142 Repeater CDMA-800 2 CH 230VAC, MRX, HP, RCU A 4720AR4540/05147 Repeater CDMA-800 2 CH 115VAC, MRX, HP B 4720AR4545/02241 Repeater CDMA-800 2+2 CH 230VAC C 4720AR4545/02243 Repeater CDMA-800 2+2 CH 21-60VDC C 4720AR4545/02247 Repeater CDMA-800 2+2 CH 115VAC C 4720AR4600/05201 Repeater BS 800 SMR IDEN 230VAC C 4740

Page 188: Repeater Specs

AR4600/05203 Repeater BS 800 SMR IDEN 21-60VDC C 4740AR4600/05207 Repeater BS 800 SMR IDEN 115VAC C 4740AR6500/00103 Repeater W-CDMA 1-2 Ch 21-60VDC B 4790AR6560/00101 Repeater W-CDMA 1-2 Ch, HP 230VAC C 4790AR6560/00103 Repeater W-CDMA 1-2 Ch, HP 21-60VDC C 4790

Page 189: Repeater Specs

Confidential InformationNot Released Repeater Products and not possible to order

Price is estimated.These products are not possible to order.Upon substantial market need the release process can take place. Delivery and lead-time must be confirmed by PM.Revision Date2002-04-16

Product nr. Information Prod. Grp.AR2111/54401 Repeater Dual 1800/900 4+4 ch FB 230VAC 4760AR2111/54402 Repeater Dual 1800/900 4+4 ch FB 230VAC RCU 4760AR4600/05204 Repeater BS 800 SMR IDEN 21-60VDC, RCU 4740AR6500/00102 Repeater W-CDMA 1-2 Ch 230VAC, RCU 4790AR6500/00104 Repeater W-CDMA 1-2 Ch 21-60VDC, RCU 4790AR6560/00102 Repeater W-CDMA 1-2 Ch, HP 230VAC, RCU 4790AR6560/00104 Repeater W-CDMA 1-2 Ch, HP 21-60VDC, RCU 4790AR6565/02202 Repeater W-CDMA 3-4 Ch 230VAC, RCU 4790AR6565/02203 Repeater W-CDMA 3-4 Ch 21-60VDC 4790AR6565/02204 Repeater W-CDMA 3-4 Ch 21-60VDC, RCU 4790EA101 25/1 Expansion Kit AMPS 4900

Page 190: Repeater Specs

Confidential InformationRCU, Fiber, Expansions kit and other Volume Delivery time

A by forecast 5 daysFC = Forecast Class B by forecast 20 daysThese products are available, possible to order C by forecast on request

Revision Date2002-04-16

X= Configurable product, Order Entry Form is requiredNote Product nr. Information FC Prod. Grp.

EA101 02/1 Software kit English B 4820EA101 09/1 Weather Shield kit C 4900EA101 10/5 RCU Kit GSM-1900, Wavecom B 4800EA101 10/6 RCU Kit GSM 900/1800, Wavecom B 4800EA101 12/1 Door switch kit B 4900EA101 14/1 Expansion Kit 2->4 ch. 1900 MHz B 4715EA101 16/1 Expansion Kit 4->6 ch. 900 MHz B 4705EA101 19/1 Expansion Kit 2->4 ch. 1800 MHz B 4710EA101 20/1 Expansion Kit EGSM 2-4 ch B 4705EA101 21/1 Expansion Kit EGSM 4-6 ch B 4705EA101 22/1 Expansion Kit 900MHz 2-4ch A 4705EA101 31/1 Expansion Kit 4-8 ch. 900MHz B 4705EA101 32/1 Dual band Kit 900, adj 16.5 MHz C 4705EA101 33/1 Dual band Kit 1800, 2 ch. LB C 4710EA101 35/1 POI 900/1800 Kit, 1-port, N-type B 4900EA101 35/2 POI 900/1800 Kit, 1-port, 7/16-type C 4900EA101 36/1 POI 900/1800 Kit, 2-port, N-type B 4900EA101 36/2 POI 900/1800 Kit, 2-port, 7/16-type C 4900EA101 37/1 POI 800/1900 Kit, 1-port, N-type C 4900EA101 37/2 POI 800/1900 Kit, 1-port, 7/16-type C 4900EA101 38/1 POI 800/1900 Kit, 2-port, N-type C 4900EA101 38/2 POI 800/1900 Kit, 2-port, 7/16-type C 4900EA101 39/1 Fiber Optic Installation Kit B 4805EA101 43/1 Expansion Kit 4-8 ch. 1800MHz B 4710EA101 47/1 R2R-Kit Internal B 4900EA101 47/2 R2R-Kit External B 4900EA101 48/1 Expansion Kit 4-6 ch. 1800MHz B 4710EA101 49/1 RCC KIT 900, Wavecom B 4800EA101 50/1 RCC KIT 1800, Wavecom B 4800EA101 52/1 RCC KIT 1900, Wavecom B 4800EA101 54/1 Expansion Kit CDMA1900 Mhz C 4735EA101 56/1 Dual band Kit BS 1800 Mhz C 4750EA101 57/1 Pole mounting bracket for Compact B 4770-4785EA101 58/1 Expansion Kit 4->6 ch 1900 Mhz C 4715EA101 59/1 Repeater Tool Kit C 4900EA101 60/1 Key Kit Compact B 4900

Page 191: Repeater Specs

EA101 61/1 Fiber Optic Maintenance Kit B 4805EA101 63/1 RCU Kit CDMA 800, Sierra B 4800EA101 64/1 RCU Kit CDMA 1900, Sierra C 4800EA101 65/1 RCU Kit AMPS 800/New C 4800EA101 66/1 RCC Kit Wireline modem B 4800EA101 70/1 Expansion Kit WCDMA 1-2 CH C 4800EA101 73/1 Hinge kit B 4900EA101 74/1 RCC Kit AMPS 800 C 4800EA101 75/1 RCC Kit CDMA 800 C 4800EA101 75/3 RCC Kit CDMA 1900 C 4800RL102 00/01 OMS Nokia Alarm Interface Demo B 4820RL102 01/01 OMS Nokia Alarm Interface Lic. B 4820RL104 00/01 OMS Single User, Demo Version B 4820RL104 01/01 OMS Single User License B 4820RL104 01/02 OMS Single User License Add. B 4820RL105 00/01 OMS Multi User, Demo Version B 4820RL105 01/01 OMS Multi User License 5 users B 4820RL105 01/02 OMS Multi User License Add. B 4820RS108/1 OMS Single User Ann. Sup. & UG B 4820RS108/2 OMS Single User Add. Sup. & UG B 4820RS108/3 OMS Multi User Ann. Sup. & UG B 4820RS108/4 OMS Multi User Add An Sup.& UG B 4820RS108/7 OMS Nokia Alarm In An Sup.& UG B 4820UA102 04/1 BBU 25Ah with 24VDC output C 4835UA102 04/2 BBU 50Ah with 24VDC output C 4835

X UA104 04/1 Solar Panel 1 C 0X UA104 04/1 Solar Panel 2 C 0X UA104 04/1 Solar Panel 3 C 0X UA104 04/1 Solar Panel 4 C 0X UA104 04/1 Solar Panel 5 C 0X UA104 04/1 Solar Panel 6 C 0X UA104 04/1 Solar Panel 7 C 0X UA104 04/1 Solar Panel 8 C 0X UA104 04/1 Solar Panel 9 C 0X UA104 04/1 Solar Panel 10 C 0X UA109 00/1 ACE FOUX UA109 01/1-A FOU Type A, excl. repeater B 4810X UA109 01/1-B FOU Type B, excl. repeater B 4810X UA109 01/1-C FOU Type C, excl. repeater B 4810X UA109 01/1-D FOU Type D, excl. repeater B 4810X UA109 01/1-WA FOU Type A, WDM, excl. repeater B 4810X UA109 01/1-WB FOU Type B, WDM, excl. repeater B 4810X UA109 01/1-WC FOU Type C, WDM, excl. repeater B 4810X UA109 01/1-WD FOU Type D, WDM, excl. repeater B 4810X UA111 00/1 ACE BMU B 4805X UA111 01/1-SS11L BMU. 1 LINE Star/Serial 1 FOT/FON B 4805X UA111 01/1-SS22L BMU. 2 LINE Star/Serial 2 FOT/FON B 4805X UA111 01/1-St12L BMU. 2 LINE Star 1 FOT/FON B 4805

Page 192: Repeater Specs

X UA111 01/1-St13L BMU. 3 LINE Star 1 FOT/FON B 4805X UA111 01/1-St14L BMU. 4 LINE Star 1 FOT/FON B 4805X UA111 01/1-St23L BMU. 3 LINE Star 2 FOT/FON B 4805X UA111 01/1-St24L BMU. 4 LINE Star 2 FOT/FON B 4805X UA111 01/1-St25L BMU. 5 LINE Star 2 FOT/FON B 4805X UA111 01/1-St26L BMU. 6 LINE Star 2 FOT/FON B 4805X UA111 01/1-St27L BMU. 7 LINE Star 2 FOT/FON B 4805X UA111 01/1-St28L BMU. 8 LINE Star 2 FOT/FON B 4805X UA111 01/1-WSS11L BMU. 1 LINE ,WDM Star/Serial 1 FOT/FON B 4805X UA111 01/1-WSS22L BMU. 2 LINE, WDM Star/Serial 2 FOT/FON B 4805X UA111 01/1-WSt12L BMU. 2 LINE, WDM Star 1 FOT/FON B 4805X UA111 01/1-WSt13L BMU. 3 LINE, WDM Star 1 FOT/FON B 4805X UA111 01/1-WSt14L BMU. 4 LINE, WDM Star 1 FOT/FON B 4805X UA111 01/1-WSt23L BMU. 3 LINE, WDM Star 2 FOT/FON B 4805X UA111 01/1-WSt24L BMU. 4 LINE, WDM Star 2 FOT/FON B 4805X UA111 01/1-WSt25L BMU. 5 LINE, WDM Star 2 FOT/FON B 4805X UA111 01/1-WSt26L BMU. 6 LINE, WDM Star 2 FOT/FON B 4805X UA111 01/1-WSt27L BMU. 7 LINE, WDM Star 2 FOT/FON B 4805X UA111 01/1-WSt28L BMU. 8 LINE, WDM Star 2 FOT/FON B 4805

UA111 02/1 ACE BMU Rack B 4805X UA113 00/1 ACE RMU B 4805X UA113 01/1-SS1L RMU. 1 LINE Star/Serial B 4805X UA113 01/1-St2L RMU. 2 LINE Star B 4805X UA113 01/1-St3L RMU. 3 LINE Star B 4810X UA113 01/1-St4L RMU. 4 LINE Star B 4810X UA113 01/1-WSS1L RMU. 1 LINE Star/Serial, WDM B 4810X UA113 01/1-WSt2L RMU. 2 LINE Star, WDM B 4810X UA113 01/1-WSt3L RMU. 3 LINE Star, WDM B 4810X UA113 01/1-WSt4L RMU. 4 LINE Star, WDM B 4810

UA115 00/1 Site Distribution Unit B 4810UA115 02/1 ACE SDU Rack B 4810VE007 96/1 External R2R Cable for Compact B 4770-4785VE008 17/1 BBU Compact Alarm Cable C 4770-4785

Page 193: Repeater Specs

Confidential InformationNew products

Prices are estimated.These products are not possible to order.When possible to order, they will be moved to "Released" or "Not released" section.Revision Date2002-04-16

PlannedProduct nr. Information Prod. Grp. order date CommentsUA101 13/1 PSU 115-230VAC/10-13VDC 1005 2002-05-31 New power supplyK310/1 PSM Compact 16-60VDC 1005 2002-05-31 DC for CompactAR4240/01201 Repeater BS CDMA 800 HP, 25 MHz 230 VAC 4740 2002-05-31AR4240/01202 Repeater BS CDMA 800 HP, 25 MHz 230 VAC RCU 4740 2002-05-31AR4240/01203 Repeater BS CDMA 800 HP, 25 MHz 21-60 VDC 4740 2002-05-31AR4240/01204 Repeater BS CDMA 800 HP, 25 MHz 21-60 VDC RCU 4740 2002-05-31AR4240/01207 Repeater BS CDMA 800 HP, 25 MHz 115 VAC 4740 2002-05-31AR4240/01208 Repeater BS CDMA 800 HP, 25 MHz 115 VAC RCU 4740 2002-05-31AR3430/01101 Repeater BS CDMA 1900 LB HP, 115 V 4755 2002-05-31AR3430/01102 Repeater BS CDMA 1900 LB HP, 115 V RCU 4755 2002-05-31AR3430/91101 Repeater BS CDMA 1900 UB HP, 115 V 4715 2002-05-31AR3430/91102 Repeater BS CDMA 1900 UB HP, 115 V RCU 4715 2002-05-31ALT1200/00201 In-train compact 900 MHz, ABW 25 MHz, 85-260 V AC/DC 4775 2002-06-15ALT1200/00202 In-train compact 900 MHz, ABW 25 MHz, 85-260 V AC/DC, RCC 4775 2002-06-15ALT1200/00203 In-train compact 900 MHz, ABW 25 MHz, 16-60 V DC 4775 2002-06-15ALT1200/00204 In-train compact 900 MHz, ABW 25 MHz, 16-60 V DC, RCC 4775 2002-06-15ALT2200/00201 In-train compact 1800 MHz, LB, ABW 25 MHz, 85-260 V AC/DC 4780 2002-06-15ALT2200/00202 In-train compact 1800 MHz, LB, ABW 25 MHz, 85-260 V AC/DC, RCC 4780 2002-06-15ALT2200/00203 In-train compact 1800 MHz, LB, ABW 25 MHz, 16-60 V DC 4780 2002-06-15ALT2200/00204 In-train compact 1800 MHz, LB, ABW 25 MHz, 16-60 V DC, RCC 4780 2002-06-15ALT2200/90201 In-train compact 1800 MHz, UB, ABW 25 MHz, 85-260 V AC/DC 4780 2002-06-15ALT2200/90202 In-train compact 1800 MHz, UB, ABW 25 MHz, 85-260 V AC/DC, RCC 4780 2002-06-15ALT2200/90203 In-train compact 1800 MHz, UB, ABW 25 MHz, 16-60 V DC 4780 2002-06-15ALT2200/90204 In-train compact 1800 MHz, UB, ABW 25 MHz, 16-60 V DC, RCC 4780 2002-06-15

Page 194: Repeater Specs

Confidential InformationLinDAS Revision Date 2002-04-16

Additional price for remote control of OCM = 5000 Skr, $476, €540

Product nr. Information Prod. Grp.UA117 01/1 OCM Star 1 FON, one RH per FON 4812UA117 01/1 OCM Star 1 FON, two RH per FON 4812UA117 01/1 OCM Star 1 FON, three RH per FON 4812UA117 01/1 OCM Star 1 FON, four RH per FON 4812UA117 01/1 OCM Star 2 FON, one RH per FON 4812UA117 01/1 OCM Star 2 FON, two RH per FON 4812UA117 01/1 OCM Star 2 FON, three RH per FON 4812UA117 01/1 OCM Star 2 FON, four RH per FON 4812UA117 01/1 OCM Star 3 FON, one RH per FON 4812UA117 01/1 OCM Star 3 FON, two RH per FON 4812UA117 01/1 OCM Star 3 FON, three RH per FON 4812UA117 01/1 OCM Star 3 FON, four RH per FON 4812UA117 01/1 OCM Star 1 FON WDM, one RH per FON 4812UA117 01/1 OCM Star 1 FON WDM, two RH per FON 4812UA117 01/1 OCM Star 1 FON WDM, three RH per FON 4812UA117 01/1 OCM Star 1 FON WDM, four RH per FON 4812UA117 01/1 OCM Star 2 FON WDM, one RH per FON 4812UA117 01/1 OCM Star 2 FON WDM, two RH per FON 4812UA117 01/1 OCM Star 2 FON WDM, three RH per FON 4812UA117 01/1 OCM Star 2 FON WDM, four RH per FON 4812UA117 01/1 OCM Star 3 FON WDM, one RH per FON 4812UA117 01/1 OCM Star 3 FON WDM, two RH per FON 4812UA117 01/1 OCM Star 3 FON WDM, three RH per FON 4812UA117 01/1 OCM Star 3 FON WDM, four RH per FON 4812UA119 01/1 RCM Single band 1-sector, fiber version 4812UA119 01/1 RCM Single band 2-sector, fiber version 4812

Page 195: Repeater Specs

UA119 01/1 RCM Single band 3-sector, fiber version 4812UA119 01/1 RCM Dual band 1-sector, fiber version 4812UA119 01/1 RCM Dual band 2-sector, fiber version 4812UA119 01/1 RCM Dual band 3 -sector, fiber version 4812UA119 01/1 RCM Tri band 1 sector, fiber version 4812UA119 01/1 RCM Single band 1-sector, coaxial version 4812UA119 01/1 RCM Single band 2-sector, coaxial version 4812UA119 01/1 RCM Single band 3-sector, coaxial version 4812UA119 01/1 RCM Dual band 1-sector, coaxial version 4812UA119 01/1 RCM Dual band 2-sector, coaxial version 4812UA119 01/1 RCM Dual band 3-sector, coaxial version 4812UA119 01/1 RCM Tri band 1-sector, coaxial version 4812ALR4600/001 Remote Hub Base unit 800 iDEN incl. FON 4770ALR4200/001 Remote Hub Base unit 800 AMPS/TDMA incl. FON 4770ALR1200/001 Remote Hub Base unit 900 incl. FON 4775ALR2200/001 Remote Hub Base unit 1800 incl. FON 4780ALR3200/001 Remote Hub Base unit 1900 incl. FON 4785ALR4600/001 Remote Hub Base unit 800 iDEN 4770ALR4200/001 Remote Hub Base unit 800 AMPS/TDMA 4770ALR1200/001 Remote Hub Base unit 900 4775ALR2200/001 Remote Hub Base unit 1800 4780ALR3200/001 Remote Hub Base unit 1900 4785ALR3242/001 Remote Hub base unit 1900/800 incl. FON 4760ALR2212/001 Remote Hub base unit 1800/900 incl. FON 4760ALR3242/001 Remote Hub base unit 1900/800 4760ALR2212/001 Remote Hub base unit 1800/900 4760Option Remote Hub 2 antenna connector splittOption Remote Hub 3 antenna connector splittOption Remote Hub 4 antenna connector splittConfig A One Remote Hub 4810Config B Two Remote Hub, fiber cabeling cascade 4810Config C Three Remote Hub, fiber cabeling cascade 4810Config D Four Remote Hub, fiber cabeling cascade 4810Config A One Remote Hub, WDM 4810Config B Two Remote Hub, fiber cabeling cascade, WDM 4810Config C Three Remote Hub, fiber cabeling cascade, WDM 4810

Page 196: Repeater Specs

Config D Four Remote Hub, fiber cabeling cascade, WDM 4810

Page 197: Repeater Specs

Confidential InformationSpare parts

"-S" = Defined sparepart incl. Package.Other spare parts processed when ordering

Revision Date2002-04-16

Product nr. InformationX K102/3-S CHA board UL, 2W X K102/4-S CHA board DL, 2W Recommended spare part dimensioning per 100 unitX K102/5-S CHA board EGSM UL X K102/6-S CHA board EGSM DL Unit No. of No. of

K103/2-S Cu Board failure rate units spare partsX K104/1-S MRX 8 Board LED board (Light Emitting Diod) 0,005 1 1

K105/1-S DIA BOARD DIA board (Distribution Board) 0,005 1 1K111/1-S LED BOARD LNA (Low Noise Amplifier) 0,015 2 3K112/1-S ALI BOARD CU (Control Unit) 0,008 1 1K118/1-S FOT Board 1310 nm ALI (Alarm Interface) 0,005 1 1K118/2-S FOT Board 1550 nm BSA board (Band Selective) 0,01 2 2K119/1-S RIA-Board BSC board (Compact) 0,015 2 3

X K122/1-S CHA 18 Board UL PA board (Power Amplifier) 0,01 2 2X K122/2-S CHA 18 Board DL PSU (Power Supply Unit), standard 0,03 1 3X K122/3-S CHA 19 Board UL PSU (Power Supply Unit), BA 0,03 1 3X K122/4-S CHA 19 Board DL PSM 0,03 1 3X K123/1-S CSA 19 Board UL DPX 0,001 2 1X K123/2-S CSA 19 Board DL DCM 0,001 2 1

K129/1-S FON Board 1310 DCB 0,001 2 1K129/2-S FON Board 1550 MRX 0,01 1 1

X K134/2-S CSA Board 15 DAB BA 0,01 1 1X K143/1 CSA Board 21 UL CSA board 0,01 2 2X K143/2 CSA Board 21 DL CHA board 0,01 2 2X K202/1-S PA 9 Board UL FOU (incl. FOT/FON) 0,01 1 1X K202/2-S PA 9 Board DL X K202/5 PA 8 Board UL AMPSX K202/6 PA 8 Board DL AMPSX K203/11 BSA 9 EGSM UL BW 16,9 MHzX K203/12 BSA 9 EGSM DL BW 16,9 MHzX K204/1 CSA 8 Board UL

Spare parts recommendations

• Only power supplies, passive components and digital subunits are subject for field replacements.

• RF-units, marked with “X” requires re-calibration on repeaterlevel and thus not possible to order. A swap repair on mainunit level is recommended.

Page 198: Repeater Specs

X K204/2 CSA 8 Board DLX K204/3 CSA 8/9 Board CDMA UL, ChinaX K204/4 CSA 8/9 Board CDMA DL, ChinaX K205/2 PA 8 Board CDMA UL/DLX K205/4 PA 8/9 Board CDMA, ChinaX K221/31 BSA board 1800 UL, 16,9 MHz LBX K221/32 BSA board 1800 UL, 16,9 MHz UBX K221/41 BSA board 1800 DL, 16,9 MHz LBX K221/42 BSA board 1800 DL, 16,9 MHz UBX K223/11 PA 19 Board TDMA ULX K223/12 PA 19 Board TDMA DLX K223/21-S PA 19 Board (CDMA) UplinkX K223/22-S PA 19 Board (CDMA) DownlinkX K223/31-S PA 18 Board UL X K223/32-S PA 18 Board DL X K224/1-S MRX 19 BoardX K225/1 BA 19 BoardX K225/2 BA 21 Board X K227/1 BA 8 BoardX K228/1 PA 20 Board ULX K229/1 PA 21 Board DL

K305/1-S PSM BoardPM291 09/1 Battery for RCUPM300 11/1 Modem 900/1800 Dual band UnicomPM300 06/2 Modem 1900 UnicomUA101 11/1-S PSU AC 230V UA101 11/2-S PSU 115VAC UA101 12/4-S PSU 230VAC/13V UA101 12/5-S PSU 115VAC 13VDC UA101 12/7-S PSU 115VAC/13 VDC BAUA101 12/8-S PSU 230V/13V BAUA101 51/1-S PSU 48VDC UA101 51/2-S PSU 24VDC UA101 52/1-S PSU DC 21-60VDCUA106 01/3 Duplexfilter GSM900UA106 02/1-S Duplex filter DCS1800 LB UA106 03/1-S Duplex filter DCS1800 UB UA106 04/1-S Duplex filter PCS1900 LB UA106 05/1-S Duplex filter PCS1900 UB UA106 07/1 Duplex filter EGSMUA106 08/1 Duplex filter AMPS

Page 199: Repeater Specs

UA106 08/3 Duplexfilter AMPSUA106 10/2 Duplex filter RGSMUA106 11/1-S Combiner 8/9UA106 12/1-S Combiner 18/19 UA106 15/1 Duplexfilter WCDMAUA106 25/1 DCC 800/900 MHz, CompactUA106 26/1 DCC 1800/1900 MHz, Compact

X UA107 14/1-S LNA GSM900 ULX UA107 14/2-S LNA GSM900 DLX UA107 14/5-S LNA AMPS ULX UA107 14/6-S LNA AMPS DLX UA107 14/7-S LNA EGSM ULX UA107 14/8-S LNA EGSM DLX UA107 15/1-S LNA 18 ULX UA107 15/2-S LNA 18 DLX UA107 15/3-S LNA 19 ULX UA107 15/4-S LNA 19 DL

UA107 16/1-S DC 800/900UA107 17/1-S DC 1800/1900UA107 21/1 DCM 8/9 Unit, MRXUA107 22/1 DCB 8/9 Unit, Booster

X UA107 23/1 LNA 21 ULX UA107 23/2 LNA 21 DLX UA107 24/1 LNA CDMA UL, ChinaX UA107 24/2 LNA CDMA DL, China

VE007 27/1 Cable (PSU 48/24VDC)