Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
AR54.15-P-1100EW Remove/install pyrofuse electrical connector 11.6.12
MODEL 207, 212, 218
P54.15-3319-07
Vehicle without CODE B03(ECO start/stop function)
1 Cover 3 Electrical connector
2 Locking pin F32 Front electrical prefuse box
Vehicle with CODE B03 (ECO start/stop function)
2 Locking pin
3 Electrical connector
G1 On-board electrical system battery
P54.15-3328-11
3 Electrical connector
4 Insulation
5 Repair wiring harness
6 Solder connector
7 Fabric tape
Page 1 of 2© Daimler AG, 2/14/17, B/02/17, ar54.15-p-1100ew, Remove/install pyrofuse electrical connectorMODEL 207, 212, 218
P54.15-3171-06
Remove
1 Disconnect battery ground line AR54.10-P-0003EW
2 Open cover (1) on front electrical prefuse box MODEL 207, 212, 218(F32) without CODE B03(ECO start/stop function)
3.1 Release locking pin (2) and disconnect MODEL 207, 212, 218electrical connection (3) from front prefuse box without CODE B03(ECO start/stop function)
(F32)
3.2 Unlock locking pin (2) and detach electrical MODEL 207, 212, 218connector (3) from positive terminal of on- with CODE B03(ECO start/stop function)board electrical system battery (G1)
4 Release locking pin and detach electrical MODEL 212.095/098/195/298connection (3) from pyrotechnical separator in interior
AR54.10-P-1180EH
5 Expose wiring harness of electrical connector (3)
6 Remove insulation (4) from wiring harness of electrical connector (3) to behind damaged
area and cut off wiring harness
7 Connect repair wiring harness (5) to wiring General repair methods for wiring harness AR00.19-P-0100Aharness of electrical connection (3)
Cut repair wiring harness (5) to same size as removed part and connect to wiring
harness of electrical connector (3) using solder connector (6). Then insulate the repaired area with fabric tape (7).
Observe the color coding of the cables of the repair wiring harness (5) and of the wiring harness of the electrical connection (3).
Install
8 Route wiring harness of electrical connector (3) to front prefuse box (F32) or to on-board Check for correct routing of wiring harness for electrical system battery (G1) or to the connector (3).pyrotechnical separator in the interior and fix in Otherwise it may be damaged by chafing or place crushing.
9.1 Connect electrical connector (3) to front MODEL 207, 212, 218prefuse box (F32) and fasten locking pin (2) in without CODE B03(ECO start/stop function)
place
9.2 Connect electrical connector (3) on positive MODEL 207, 212, 218terminal of on-board electrical system battery with CODE B03(ECO start/stop function)(G1) and fasten locking pin (2) in place
10 Connect electrical connection (3) to MODEL 212.095/098/195/298pyrotechnical separator in interior and lock locking pin (2)
AR54.10-P-1180EH
11 Close cover (1) on front prefuse box (F32) MODEL 207, 212, 218
without CODE B03(ECO start/stop function)
12 Connect ground cable to battery AR54.10-P-0003EW
Page 2 of 2© Daimler AG, 2/14/17, B/02/17, ar54.15-p-1100ew, Remove/install pyrofuse electrical connectorMODEL 207, 212, 218