RC952-FEE1 (a) Commands Notebook 200810

www.raisecom.com

RC952-FEE1 (A) Commands Notebook

Legal Notices

Raisecom Technology Co., Ltd makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Raisecom Technology Co., Ltd shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Warranty.

A copy of the specific warranty terms applicable to your Raisecom product and replacement parts can be obtained from Service Office.

Restricted Rights Legend.

All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Raisecom Technology Co., Ltd. The information contained in this document is subject to change without notice.

Copyright Notices.

Copyright ©2008 Raisecom. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in Writing from Raisecom Technology Co., Ltd.

Trademark Notices

is the trademark of Raisecom Technology Co., Ltd.

Java™ is a U.S. trademark of Sun Microsystems, Inc.

Microsoft® is a U.S. registered trademark of Microsoft Corporation.

Windows NT® is a U.S. registered trademark of Microsoft Corporation.

Windows® 2000 is a U.S. registered trademark of Microsoft Corporation.

Windows® XP is a U.S. registered trademark of Microsoft Corporation.

Windows® and MS Windows® are U.S. registered trademarks of

Microsoft Corporation.

Contact Information

Technical Assistance Center

The Raisecom TAC is available to all customers who need technical assistance with a Raisecom product, technology, or, solution. You can communicate with us through the following methods:

Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road,

Haidian District, Beijing 100085

Tel: +86-10-82883305

Fax: +86-10-82883056

World Wide Web

You can access the most current Raisecom product information on the World Wide Web at the following URL:

http://www.raisecom.com

Feedback

Comments and questions about how the RC952-FEE1 system software works are welcomed. Please review the FAQ in the related manual, and if your question is not covered, send email by using the following web page:

http://www.raisecom.com/en/xcontactus/contactus.htm.

If you have comments on the RC952-FEE1 specification, instead of the web page above, please send comments to:

[email protected]

We hope to hear from you!

CONTENTS Release Notes------------------------------------------------------------------------------------------------- 5 Chapter 1 How to Use the Commands Line ----------------------------------------------------- 1

1.1 Software and hardware environment -----------------------------------------------------------------------------1 1.2 Explanation of symbols in the command lines----------------------------------------------------------------1 1.3 Command line modes --------------------------------------------------------------------------------------------------2

Chapter 2 Management Commands of RC952-FEE1---------------------------------------- 3 2.1 chassis command -------------------------------------------------------------------------------------------------------3 2.2 slot mode -------------------------------------------------------------------------------------------------------------------4 2.3 show slot -------------------------------------------------------------------------------------------------------------------4 2.4 remote mode --------------------------------------------------------------------------------------------------------------5 2.5 show device ---------------------------------------------------------------------------------------------------------------5 2.6 show info -------------------------------------------------------------------------------------------------------------------5 2.7 reset --------------------------------------------------------------------------------------------------------------------------6 2.8 show interface ------------------------------------------------------------------------------------------------------------7 2.9 interface e1 ----------------------------------------------------------------------------------------------------------------7 2.10 local_loopback -----------------------------------------------------------------------------------------------------------8 2.11 remote_loopback --------------------------------------------------------------------------------------------------------9 2.12 noloopback ----------------------------------------------------------------------------------------------------------------9 2.13 bert -------------------------------------------------------------------------------------------------------------------------10 2.14 fault-pass ----------------------------------------------------------------------------------------------------------------- 11 2.15 crc-auto -------------------------------------------------------------------------------------------------------------------12 2.16 clock-mode --------------------------------------------------------------------------------------------------------------12 2.17 frame-mode --------------------------------------------------------------------------------------------------------------13 2.18 timeslot--------------------------------------------------------------------------------------------------------------------14 2.19 interface eth -------------------------------------------------------------------------------------------------------------15 2.20 autonegotiate -----------------------------------------------------------------------------------------------------------16 2.21 speed duplex ------------------------------------------------------------------------------------------------------------17 2.22 flowcontrol ---------------------------------------------------------------------------------------------------------------18 2.23 shutdown -----------------------------------------------------------------------------------------------------------------18

Release Notes

Date of Release Manual Version Software Version Revisions

20090304 200810 First release

Preface

About This Manual

This manual introduces command lines and relevant interfaces of the RC952-FEE1 (A) software.

Who Should Read This Manual

This manual is a valuable reference for sales and marketing staff, after service staff and telecommunication network designers. For those who want to have an overview of the features, applications, structure and specifications of RC952-FEE1 (A) device, this is also a recommended document.

Organization

This manual is about the management configuration commands of RC952-FE78E1 (A) local interface converter.

Compliance

The RC series products developed by Raisecom are strictly complied with the following standards as well as ITU-T, IEEE, IETF and related standards from other international telecommunication standard organizations:

YD/T900-1997 SDH Equipment Technical Requirements - Clock

YD/T973-1998 SDH 155Mb/s and 622Mb/s Technical conditions of optical transmitter module and receiver module

YD/T1017-1999 Network node interface for the Synchronous Digital Hierarchy (SDH)

YD/T1022-1999 Requirement of synchronous digital hierarchy (SDH) equipment function

YD/T1078-2000 SDH Transmission Network Technique Requirements-Interworking of Network Protection Architectures

YD/T1111.1-2001 Technical Requirements of SDH Optical Transmitter/Optical Receiver Modules——2.488320 Gb/s Optical Receiver Modules

YD/T1111.2- 2001 Technical Requirements of SHD Optical Transmitter/Optical Receiver Modules——2.488320 Gb/s Optical Transmitter Modules

YD/T1179- 2002 Technical Specification of Ethernet over SDH

G.703 Physical/electrical characteristics of hierarchical digital interfaces

G.704 Synchronous frame structures used at 1544, 6312, 2048, 8448 and 44 736 kbit/s hierarchical levels

G.707 Network node interface for the synchronous digital hierarchy (SDH)

G.774 Synchronous digital hierarchy (SDH) - Management information model for the network element view

G.781 Synchronization layer functions

G.783 Characteristics of synchronous digital hierarchy (SDH) equipment functional blocks

G.784 Synchronous digital hierarchy (SDH) management

G.803 Architecture of transport networks based on the synchronous digital hierarchy (SDH)

G.813 Timing characteristics of SDH equipment slave clocks (SEC)

G.823 The control of jitter and wander within digital networks which are based on the 2048 kbit/s hierarchy

G.825 The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy (SDH)

G.826 End-to-end error performance parameters and objectives for international, constant bit-rate digital paths and connections

G.828 Error performance parameters and objectives for international, constant bit-rate synchronous digital paths

G.829 Error performance events for SDH multiplex and regenerator sections

G.831 Management capabilities of transport networks based on the synchronous digital hierarchy (SDH)

G.841 Types and characteristics of SDH network protection architectures

G.842 Interworking of SDH network protection architectures

G.957 Optical interfaces for equipments and systems relating to the synchronous digital hierarchy

G.691 Optical interfaces for single channel STM-64 and other SDH systems with optical amplifiers

G.664 Optical safety procedures and requirements for optical transport systems

I.731 ATM Types and general characteristics of ATM equipment

I.732 ATM Functional characteristics of ATM equipment

IEEE 802.1Q Virtual Local Area Networks (LANs)

IEEE 802.1p Traffic Class Expediting and Dynamic Multicast Filtering

IEEE 802.3 CSMA/CD Access Method and Physical Layer Instruction

www.raisecom.com User Manual

1

Chapter 1 How to Use the Commands Line

1.1 Software and hardware environment

Hardware environment: RC002 device platform

PC serial interface

Software environment: WIN98/WIN2000/WINDOWS XP

1.2 Explanation of symbols in the command lines

Mode Mode Description Access Identifier

User EXEC Users are authorized to

configure basic information and display parameters, etc.

Log onto the device and input user name and

password RAISECOM>

Privileged EXEC

Users are authorized to configure basic information of RC002, such as system time,

and display parameters. Configuring running

information is not authorized.

Use the command enable under user EXEC mode.

RAISECOM#

Global configuration

Users are authorized to configure all running

parameters of RC002 device

Use the command config under privileged EXEC

mode. RAISECOM(config)#

Slot configuration

Users are authorized to configure running parameters

of local device in slot.

Use the command slot under global configuration mode.

RAISECOM (config-slot/PATH)# PATH: path of slot

Remote configuration

Users are authorized to configure all running

parameters of remote devices

Use the command remote under global configuration

mode.

RAISECOM (config-remote/PATH)# PATH: path of remote device

Interface configuration

Users are authorized to configure parameters of remote

Ethernet electrical interface, Ethernet optical interface.

Use the command interfaceunder slot configuration

mode or remote configuration mode.

RAISECOM (config-TYPE/PATH)# TYPE: interface type like eth, fx-eth, etc; PATH: path of interface

Note: Device Path Definition:

Slot path: “/n”, where n indicates slot number; Local device path: “/n/a”, where n indicates chassis number, a indicates slot number; Remote device path: “/n/a/b/c…”, where n indicates chassis number, a indicates slot number,

b indicates first layer remote device number; c indicates second layer remote device number. RC002 is able to bear two layers of remote devices at most.

Interface path: local interface path is denoted as “local device path/port number”; remote interface path is denoted as “remote device path/port number”.


2

1.3 Command line modes

1. The commands are all stop at command keyword before the first parameter.

2. All optional parameters should be bracketed into a “[ ]”, regardless of how many parameters there are. Parameters should be separated by “|”.

3. In the case of any choices of required parameters or command keywords, all parameters and command keywords should be bracketed into a “()”. Parameters and command keywords should be separated by “|”.


3

Chapter 2 Management Commands of RC952-FEE1

This chapter including the commands of:

chassis show slot remote mode show device show info reset show interface interface e1 local_loopback remote_loopback noloopback bert fault-pass crc-auto clock-mode frame-mode timeslot interface eth autonegotiate speed duplex flowcontrol shutdown

2.1 chassis command

[Function]

Choose chassis management command

[Default]

Chassis 1

[Command Mode]

Global configuration mode

[Instructions]

Default to choose chassis 1 in config mode

[Example]

Choose chassis 1 management mode:

RAISECOM (config)#chassis 1


4

[Supporting card type]

All

2.2 slot mode

[Function]

Enter local card management mode

[Command Mode]

Slot configuration mode

[Instructions]

In config mode

[Example]

Enter local card management mode:

RAISECOM (config)

RAISECOM (config)#slot 12

Note: the local card is plugged at slot 12 of RC002 chassis 1.


RC952-FEE1

2.3 show slot

[Function]

Show cards in slot at local side

[Command Mode]


[Instructions]

In config mode

[Command Execution Echo]

Current chassis id is X

Slot Y: RC952-FEE1-A-master

[Example]

Show cards in slot at local side:

RAISECOM (config)# show slot


Supporting RC002 network manageable cards


5

2.4 remote mode

[Function]

Enter remote card management mode

[Command Mode]

Remote configuration mode

[Instructions]

In config mode

[Example]

Enter remote card management mode:

RAISECOM (config)# remote 12 1

Note: The device is plugged at slot 12 of RC002 chassis 1.


Supporting RC952-FEE1-A-master

2.5 show device

[Function]

Show cards in slot at remote side

[Command Mode]


[Instructions]

In config mode


Current chassis id is X

remoteI Y: RC952-FEE1-A-slave

[Example]

Show cards in slot at remote side:

RAISECOM (config)# show device


Supporting RC002 network manageable cards

2.6 show info

[Function]

Show detailed information of device


6

[Command Mode]

Slot configuration mode, Remote configuration mode

[Instructions]

Use this command in slot configuration mode and remote configuration mode

[Example]

Show local device configuration information at slot 12 chassis 1:

RAISECOM (config-slot/1/12)# show info

Show remote layer-1 number 1 device configuration information at slot 12 chassis 1:

RAISECOM (config-remote/1/12/1)# show info



Supporting RC952-FEE1-A-master and RC952-FEE1-A-slave

2.7 reset

[Function]

reset

reset

[Command Mode]


[Instructions]

Use this command in slot configuration mode and remote configuration mode


Set successfully

Succeed in executing the command.

Set unsuccessfully

Fail to execute the command.

[Example]

Reset:

RAISECOM (config-slot/1/12)# reset

RAISECOM (config-remote/1/12/1)# reset




7

2.8 show interface

[Function]

Show configuration information of interface

[Command Mode]

Eth interface configuration mode, fx-eth interface configuration mode

[Instructions]

Use this command in eth interface configuration mode and fx-eth interface configuration mode

[Example]

Show configuration information of local eth interface:

RAISECOM (config-eth/1/12/1)# show interface

Show configuration information of local e1 interface:

RAISECOM (config-e1/1/12/1)# show interface

Show configuration information of remote eth interface:

RAISECOM (config-eth/1/12/1/1)# show interface

Show configuration information of remote e1 interface:

RAISECOM (config-e1/1/12/1/1)# show interface




2.9 interface e1

[Function]

Enter e1 interface mode

interface e1 1

[Parameter]

1: e1 port number

[Command Mode]


[Example]

Enter interface e1 1:

RAISECOM(config-slot/1/12)# interface e1 1


8

RAISECOM(config-remote/1/12/1)# interface e1 1



[Relevant Commands]

Commands Description

show interface Show interface configuration information.

2.10 local_loopback

[Function]

Configure e1 interface loopback

local_loopback (internal | external | double)

Only local device supports this command.

[Parameter]

internal: local device internal loop enable, this device is not in support of this command

external: local device external loop enable

double: local device bi-directional loop disable, this device is not in support of this command

[Default]

No loop

[Command Mode]

Interface e1 configuration mode


Set successfully


Set unsuccessfully


[Example]

Configure local interface e1 external loop:

RAISECOM (config-slot/1/10)# interface e1 1

RAISECOM (config-e1/1/10/1)# local_loopback external



[Relevant Commands]




9

2.11 remote_loopback

[Function]

Configure e1 interface loopback

remote_loopback (internal | external | double)


[Parameter]

internal: remote device internal loop enable, this device is not in support of this command

external: remote device external loop enable

double: remote device bi-directional loop disable, this device is not in support of this command

[Default]

No loop

[Command Mode]



Set successfully


Set unsuccessfully


[Example]

Configure remote interface e1 external loop:


RAISECOM (config-e1/1/10/1)# remote_loopback external



[Relevant Commands]



2.12 noloopback

[Function]

Cancel e1 interface loopback

no loopback (internal | external | double)


[Default]


10

No loop

[Command Mode]



Set successfully


Set unsuccessfully


[Example]

Cancel local interface e1 external loop:


RAISECOM (config-e1/1/10/1)# noloopback



[Relevant Commands]



2.13 bert

[Function]

Configure BERT function

bert(enable | disable)


[Parameter]

enable: enable bert function

disable: disable bert function

[Default]

disable

[Command Mode]



Set successfully


Set unsuccessfully


11


[Example]

Configure local e1 bert function enable:


RAISECOM (config-e1/1/10/1)# bert enable



[Relevant Commands]



2.14 fault-pass

[Function]

Configure fault pass-through function of interface e1 and interface eth

fault-pass (enable | disable)


[Parameter]

enable: enable

disable: disable

[Command Mode]



Set successfully


Set unsuccessfully


[Example]


RAISECOM (config-e1/1/10/1)# fault-pass enable



[Relevant Commands]




12

2.15 crc-auto

[Function]

E1 CRC function

crc-auto (enable | disable)


[Parameter]

enable: enable CRC function of e1

disable: disable CRC function of e1

[Default]

disable

[Command Mode]



Set successfully


Set unsuccessfully


[Example]

Enable local e1 CRC function:


RAISECOM (config-e1/1/10/1)# crc-auto enable



[Relevant Commands]



2.16 clock-mode

[Function]

Clock mode of e1

clock-mode(master | secondary)


[Parameter]

master: E1 clock is in master clock mode


13

secondary: E1 clock is in slave clock mode

[Default]

master

[Command Mode]



Set successfully


Set unsuccessfully


[Example]

Configure local e1 in master clock mode:


RAISECOM (config-e1/1/10/1)# clock master



[Relevant Commands]



2.17 frame-mode

[Function]

Transmission mode of E1 frame

frame-mode(framed | unframed)


[Parameter]

framed: framed transmission mode

unframed: unframed transmission mode

[Default]

unframed

[Command Mode]



Set successfully


14


Set unsuccessfully


[Example]

Configure local e1 in framed transmission mode:


RAISECOM (config-e1/1/10/1)# frame-mode frame



[Relevant Commands]



2.18 timeslot

[Function]

Setting of the 31 E1 timeslots

timeslot <1|31>


[Parameter]

<1|31>: use integer to denote if the timeslot bit among the 31 timeslots is occupied, hereinto, “,” and “-” can also be used to indicate timeslot occupation condition.

[Default]

Keep consistent with factual status

[Command Mode]



Set successfully


Set unsuccessfully


[Example]

Configure timeslot of local e1, the former 4 timeslots of e1 to be occupied: (method 1)


RAISECOM (config-e1/1/10/1)# timeslot 1-4


15

Configure timeslot of local e1, the former 4 timeslots of e1 to be occupied: (method 2)


RAISECOM (config-e1/1/10/1)# timeslot 1, 2, 3, 4

Configure timeslot of local e1, the former 10 timeslots of e1 to be occupied:


RAISECOM (config-e1/1/10/1)# timeslot 1-10

Configure timeslot of local e1, e1 timeslot 1 and e1 timeslots 5-20 to be occupied:


RAISECOM (config-e1/1/10/1)# timeslot 1, 5-20

Configure timeslot of local e1, e1 timeslot 1-10 and e1 timeslots 5-20 to be occupied:


RAISECOM (config-e1/1/10/1)# timeslot 1-10, 15-20



[Relevant Commands]



2.19 interface eth

[Function]

Enter Ethernet electrical interface mode

interface eth 1

[Parameter]

1: electrical interface number

[Command Mode]


[Example]

Enter electrical interface 1:

RAISECOM(config-slot/1/12)# interface eth 1

RAISECOM(config-remote/1/12/1)# interface eth 1

Note: RC952-FEE1-A is plugged at slot 12 of chassis 1.


16



[Relevant Commands]



2.20 autonegotiate

[Function]

Configure auto-negotiation for Ethernet electrical interface and Ethernet optical interface

autonegotiate (enable | disable)


[Parameter]

enable: enable

disable: disable

[Default]

enable

[Command Mode]

Interface eth configuration mode


Set successfully


Set unsuccessfully


[Example]

Enable local RC952-FEE1-A-master Ethernet interface auto-negotiation function:

RAISECOM (config-slot/1/10)# interface eth 1

RAISECOM (config-eth/1/10/1)# autonegotiate enable

Enable remote RC952-FEE1-A-slave Ethernet interface auto-negotiation function:

RAISECOM (config-remote/1/10)# interface eth 1

RAISECOM (config-eth/1/10/1)# autonegotiate enable

Note: the device is plugged at slot 10 of chassis 1.




17

[Relevant Commands]



2.21 speed duplex

[Function]

Configure speed and duplex mode for Ethernet interface

speed (10|100) duplex (full-duplex|half-duplex)

[Parameter]

(10|100): set port speed at 10M or 100M

(full-duplex|half-duplex): interface working mode to be full-duplex or half-duplex

[Command Mode]


[Instruction]

Port speed and duplex mode can only be set when auto-negotiation function disable.


Set successfully


Set unsuccessfully


[Example]

Set local eth interface speed at 100M, working in full-duplex mode:


RAISECOM (config-eth/1/12/1)# speed 100 duplex full-duplex

Set remote eth interface speed at 100M, working in full-duplex mode:

RAISECOM (config-remote/1/12)# interface eth 1

RAISECOM (config-eth/1/12/1/1)# speed 100 duplex full-duplex

Note: the device is plugged at slot 12 of RC002 chassis 1.



[Relevant Commands]




18

2.22 flowcontrol

[Function]

Flow control of Ethernet interface

flowcontrol (enable | disable)

[Parameter]

enable: enable flow control of Ethernet interface

disable: disable flow control of Ethernet interface

[Command Mode]


[Instructions]

Use this command in interface eth configuration mode


Set successfully


Set unsuccessfully


[Example]


RAISECOM (config-eth/1/12/1)# flowcontrol enable

RAISECOM (config-remote/1/12/1)# interface eth 1

RAISECOM (config-eth/1/12/1/1)# flowcontrol enable



2.23 shutdown

[Function]

Shutdown Ethernet electrical interface, no shutdown command can used to open the interface

shutdown

no shutdown

[Default]

Interface open

[Command Mode]



19

[Example]

Shutdown local Ethernet electrical interface:


RAISECOM (config-eth/1/12/1)# shutdown

Shutdown remote Ethernet electrical interface:

RAISECOM (config-remote/1/12/1)# interface eth 1

RAISECOM (config-eth/1/12/1/1)# shutdown

Note: the device is plugged at slot 12 of RC002 chassis 1.



[Relevant Commands]



Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road, Haidian District, Beijing Postcode: 100085 Tel: +86-10-82883305 Fax: +86-10-82883056 Email: [email protected] http://www.raisecom.com

Documents

RC952-FEE1 (a) Commands Notebook 200810