Quick Start Guide - WordPress.comYour movies saved in your Collection will have a movie reel in the upper left-hand corner. Click on the movie you want to export. It will highlight

Quick Start Guide

D M C 3 _ 1 0 0 6 0 6 R S 0 4 . i n d d , S p r e a d 1 o f 1 8 - P a g e s ( 3 6 , 1 ) 1 0 / 1 4 / 0 6 4 : 3 6

Digital Blue Movie Creator 3.0Quick Start Guide

TM and © 2007 Digital Blue, Inc. All rights reserved.

Innovation starts here.www.PlayDigitalBlue.com

D M C 3 _ 1 0 0 6 0 6 R S 0 4 . i n d d , S p r e a d 2 o f 1 8 - P a g e s ( 2 , 3 5 ) 1 0 / 1 4 / 0 6 4 : 3 6

Table of Contents

i

Table of Contents

Getting Started

Using the Camera

Using the Software

Additional Help

3

4

23

29


Important: Install the software before connecting the camera to your computer.

Installing the software

1. Insert the Digital Movie Creator software CD-ROM into your CD-ROM drive.

2. If the program doesn’t automatically begin, go to the desktop and double-click My Computer. Double-click the CD-ROM drive that contains the Digital Movie Creator software. If this doesn’t start the installation program, double click setup.exe.

3. Follow the instructions on the screen.

Note: To install on several computers over a network, see instructions in NetworkInstall.txt on the installation CD.

Connecting the camera to the computer

To connect the camera to the computer:

1. Connect the USB cable on the camera’s base to the USB port on your computer.

2. Press the camera firmly into the camera base. The camera will beep and the USB icon is shown on the Display Screen when it connects to the computer.

3. Launch the Digital Movie Creator software application using the shortcut on the desktop. On the first launch, the audio setup wizard will open before the application opens.

4. When the audio setup wizard opens, select your PC sound card (usually the first item on the list) as the preferred device in order to use your microphone when recording.

2


Installing the batteries

The camera is powered by four AAA batteries. To install the camera batteries:

1. Carefully remove the small screw at the bottom of the camera using a small Phillips head screwdriver.

2. Slide the battery compartment back and lift the cover to the open position.

3. Insert the batteries using the battery polarity symbols (+ and -) as a guide.

4. Turn the camera on by pressing the Snapshot or Record button.

3

Getting Started


Camera Controls

4

Built-in Microphone

Record Button

USB Cable

Camera Base

Camera Lens

SD Memory Card Slot

TV Out

Battery Compartment

Display Screen

Snapshot Button

Eyepiece

Navigation Buttons

TV Out Cable

To launch the Help file: Click Start > Programs > Digital Blue Digital Movie Creator 3.0 > Digital Movie Creator 3.0 Help

For additional product support visit our website at:www.digitalbluecorp.com and select Customer Service.

If you are still having problems with this product, contact Customer Support at 888-800-0502.

29

Additional Help


Share your movie with friends and family

Now that you’ve created your first movie, you can share it with your friends and family.

To show friends and family on your computer:

1. Click the Share button to open the Share screen.

2. Press the Play button to start your movie.

To export your movie:

1. Save your movie by clicking the Save button.

2. Open the collection screen by clicking the Collection screen button.

3. Your movies saved in your Collection will have a movie reel in the upper left-hand corner. Click on the movie you want to export. It will highlight in green.

4. Click the Export button.

5. Choose where you want to save the exported file. The file will save in the My Documents folder unless you change the location.

Now you can e-mail the file (for smaller movies) or burn it to a CD (for larger movies) and share with friends and family.

28

Snapshot Button– Use the Snapshot button to capture still images with your camera.

Built-in Microphone– The microphone automatically records sounds as you capture video clips.

Camera Lens– Make sure to keep the camera lens clean and clear when trying to cap-ture images/video.

Camera Base– The USB cable on the camera’s base connects to your computer. When the camera is in the base and the software is running, you can download pictures, and capture images and video clips in the software.

USB Cable– Connects your camera to your computer, so you can download images to your computer when the camera is in the base.

Eyepiece– Look through the eyepiece to center your subject in the viewfinder.

Display Screen– Use the Display Screen to preview your shots and to view the menu.

Record Button– Use the Record Button to record video with your camera.

Navigation Buttons– Use the Navigation buttons for making selections from the menu or to control zooming while capturing a video. These buttons don’t work when your camera is attached to your computer.

SD Memory Card Slot– The SD Memory Card slot allows you to use your own memory card to store more images and videos on your camera. (SD card not included.)

TV Out– View your videos on the TV screen by using the TV Out cable.

Battery Compartment– Change the batteries by opening the Battery Compartment.

TV Out Cable– Connects your camera to your TV allowing you to view your movies on the screen.

5

Using the Camera


Camera Display Screen

The Camera Display screen provides information about your camera settings.

Battery Status Icon– Shows how much battery life the camera has left. When the criti-cally low image appears make sure to change your batteries immediately.

Full = Medium = Low = Critically Low =

Zoom Level– Indicates how much digital magnification you are using to shoot your subject. You can zoom in on your subject with up to four times digital magnification.

Image Quality– Shows whether the camera is filming in Normal or High Quality.

Normal = High =

6

Zoom levelBattery status

Active storage mediumMemory usage

Image qualitySnapshot typeCapture typeN umber of additional images that

can be stored Number of stored images

Preview your movie

While you’re making your movie, you might want to see how it looks before releasing the final cut.

To preview your movie, click the Play button.

27

Using the Software


Have fun with your movie

The Create screen has lots of cool ways to make your movie even better!

The Tools menu lets you add scrolling credits, titles, paint, and special movie filters to scenes.

The Special Effects menu has fun animated effects-- like aliens, explosions, and an erupting volcano-- that you can add to your movies.

The Sound Effects menu has fun sounds and music. You can also record your own music or singing as a background music track to play throughout your movie.

Tools menu

Sound Effects menu

Special Effects menu

26

Snapshot Type– Displays the type of capture when the Snapshot button is pressed.

Single = Timer on = Burst =

Capture Type– Indicates whether you are taking a snapshot or a video clip.

Snapshot = Video =

When you are playing back your movies you will see these symbols indicating you are viewing a snapshot or playing a video clip.

Snapshot = Video =

Memory Type– Shows which type of memory you currently are using.

Internal = No icon SD Memory Card =

Memory Level– Represents the amount of memory that has been used. There are several stages of memory usage.

Zero Memory Used = Memory Almost Full = Memory Full =

Delete– Flashes as you delete images from the camera.

Counter– Shows the number of images you have captured and how many you can still capture.

7

Using the Camera


Capturing video with the camera

When you turn on the camera, you’re in Live Preview Mode.

To record video:

1. Open the Display Screen and press the Snapshot or Record button to turn on the camera.

2. Locate the subject of your video using the Eyepiece or Display Screen.

3. Press the Record button to start recording.

4. When you have captured all the video you want, press the Record button again to stop recording.

5. You can play your video on the camera’s Display Screen (see Viewing images and movies on the Display Screen) or on your computer (by connecting the camera to your com-puter using the camera base and USB cable) with the Digital Movie Creator software.

Note: To zoom in on your subject, press the Up Arrow button. To zoom out, press the Down Arrow button.

8

Organize your scenes into a movie

Once you have recorded your scenes, you can use the Storyboard to make your scenes into a movie.

1. Click the Create screen button to open the Create screen.

When the scene opens, it shows the Collections screen and the Storyboard.

2. Click on one of the scenes you created. If you don’t see it, click on the green arrows to see more scenes.

3. Click and drag your scene to the Storyboard.

Repeat this step to add other scenes and images to your video.

4. Once you have added all the scenes you want to your movie, click the Collection screen button to close the Collection screen.

Note: If you decide you want to add more scenes later, you can open the collection screen again at any time.

25

Using the Software

D M C 3 _ 1 0 0 6 0 6 R S 0 4 . i n d d , S p r e a d 1 0 o f 1 8 - P a g e s ( 1 0 , 2 7 ) 1 0 / 1 4 / 0 6 4 : 3 6

Rename the scene so you can find it easily

The scene you just recorded is now in the Temporary collection.

1. Open the Collections screen by clicking the Collection button at the top of the screen.

2. Click the title under the scene you just recorded and type in a new name.

3. Press the Enter key on your keyboard to finish renaming your scene.

Save your scene in the Permanent collection

To save the scene, you have to move it from the Temporary collection to the Permanent collection.

1. In the Temporary collection, click on the scene you just created and renamed.

2. In the lower left-area of the of the Collection window, you’ll see your transfer options:

3. Press the One button to move the scene from the Temporary collection to the Permanent collection.

4. Click the Collection screen button to close it.

24 9

Using the Camera

Taking pictures with the camera

To take pictures with your camera, press the Snapshot button (on the top of the camera) to enter Snapshot mode. The first time you press the Snapshot button it will capture one picture immediately. Hold the camera still until the picture has been captured.

Once you’re in Snapshot mode, you can choose to make the Snapshot button take one picture at a time (single), 3 pictures in a row (burst), or wait 10 seconds before taking the pictures (timer).

To change this setting:


2. Use the Left Arrow button to change the icon on the Display Screen.


3. Once you see the icon you want, press the Snapshot button.



Viewing images and movies on the display screen

You can view all the images and videos in your camera’s menu by switching to Playback Mode.


2. Use the OK button on the Navigation Pad to go to the Main Menu.

3. Press the Down Arrow button until Playback is highlighted.

4. Use the OK button to select Playback.

5. Your first image or a still image of the first frame of your first video will be shown on the Display Screen.

In Playback Mode, you can do the following:

• Press the Right Arrow button to see the next image or video.

• Press the Left Arrow button to see the previous image or video.

• Press the Down Arrow button to see thumbnails of all your images/videos.

• Press the Up Arrow to enter the Image File Menu where you can Delete images/videos or Protect images/videos from ever being deleted.

• Press the OK button to play videos.

Note: To go back to capturing images/video, press the Snapshot or Record button.

10

Making your first movie

It’s fun to make movies using the software that came with your camera!

Shooting a scene with the camera

With your camera connected to your computer you can record movies using the software.To shoot a scene using the software:

1. Place your camera in its base and attach it to your computer (remember that the software MUST be installed FIRST).

2. Double-click on the Digital Blue Digital Movie Creator 3.0 icon on your desktop to start the software. If you don’t have an icon on your desktop, you can click Start>Programs (or All Programs)>Digital Blue Digital Movie Creator 3.0> Digital Movie Creator 3.0 to start the software.

3. When the software starts, you’ll be on the Live Screen where you’ll see what the camera sees on your screen. Make sure the subject you want is in front of the camera.

4. To start recording, press the Record button:

5. When you have captured all the video you want in the scene, press the same button (which is now red.)

Notice that the scene you just created appears in the small window on the screen. Click the Play button to preview it.

23

Using the Software


Anti-flicker settings

Indoor lighting flickers at different rates around the world. The camera is set to adjust for light that flickers at 60 hertz when you buy it. This prevents you from seeing flickers when you play the video back on a TV or computer.

In the US and North America, light flickers at 60 hertz. In the UK, Europe, and other locations, you may want to change to 50 hertz.

To change the anti-flicker settings:



3. Press the Down Arrow button until Setup is highlighted and press the OK button to select.

4. From the Setup Menu, use the Up and Down Arrow buttons to highlight TV Out and Lighting and press the OK button to select.

5. Use the Up and Down Arrow buttons to highlight either 60HZ or 50HZ.

6. Press the OK button to set the anti-flicker.

22 11

Using the Camera

Deleting images and video from the camera

You can delete images and video from the camera in 3 ways: delete one item at a time; delete the last item; or delete all items on the camera at once.

To delete one item at a time





5. Your first image or a still image of the first frame of your first video will be shown on the Display Screen. Use the Right of Left Arrow button to scroll through images and videos until you see the item you want to delete.

6. When the item you want to delete is on the Display Screen, press the Up Arrow button to enter the Image File Menu.

7. Highlight Delete using the Down Arrow Button and press the OK button to select.

8. When asked to confirm that you want to delete the item, press the OK button to select “Yes”.

9. When your image is deleted, you’ll return to scrolling through images/videos.


To delete the last picture/video you took with the camera:



3. Press the Down Arrow button until Delete is highlighted and press the OK button to select.

4. From the Delete Menu, highlight Delete Last using the Down Arrow button and press the OK button to select.


6. The last item you recorded is now deleted.

12

3. If the inputs are marked using red, yellow, and white, match the corresponding end of the cable to the input (i.e., plug the red end of the cable into the red input). If the inputs are not marked with color: plug the yellow end of the cable into the Video input; the white end of the cable into Audio- Left (or “L”) input; and the red end of the cable into the Audio-Right (or “R”) input. If you leave any of these cable ends unconnected, make sure that the metal part does not touch any other metal objects.

4. Connect the black end of the TV out cable to thecamera’s TV out connection.

5. Press the Snapshot or Record button to turn on your camera. You’ll be able to see the Live Preview on your TV screen. You can also access the menus to view the images and videos you have captured. Note: If you’ve plugged your camera into your TV’s secondary or auxiliary input, you may need to change the channel or select the appropriate input from your TV’s menu in order to see the camera’s images. TVs vary, so consult the manual that came with your TV for more details.

21

Using the Camera


To change the TV out format:





5. Use the Up and Down Arrow buttons to highlight either NTSC or PAL.

6. Press the OK button to set the TV out format.

Using the camera’s TV out feature

With the TV-out feature, you can use a regular TV to share your videos/pictures with friends & family. You will need the TV-out cable included with your Digital Movie Creator to use this feature. To connect your camera to a TV: 1. Carefully pull back on the top end of the cover and swivel it out of the way.

2. Locate the Audio/Video inputs on your TV.

20

To delete all items on the camera at once:




4. From the Delete Menu, highlight Delete All using the Down Arrow button and press the OK button to select.

5. When asked to confirm that you want to delete all, use the Down Arrow to highlight “Yes.” Press the OK button to select.

6. All items are now deleted.

To protect items from being deleted:



3. Press the Down Arrow button until Playback is highlighted. Press the OK button to select.


5. Use the Right Arrow button to scroll through images and videos until you see the item you want to protect.

Using the Camera

13


6. When the item you want to protect is on the Display Screen, press the Up Arrow button to enter the Image File Menu.

7. Highlight Protect using the Down Arrow Button and press the OK button to select.

8. From the protect menu, use the Up and Down Arrow buttons to select Lock and press OK to select.

9. Your video or image is now protected and won’t be deleted if you accidentally select Delete or Delete All.

Note: You’ll need to unprotect videos and images if you want to delete them later.

Choosing the image or video quality

There are two quality settings:

High- Images will look clear, but will take more space than Normal quality images.

Normal - Images take up less space, but aren’t as clear as high quality images.

To change to image quality:


2. Press the Right Arrow button to change the image quality.

3. The icon on the Display Screen will change to indicate your choice.

14

Note: Be sure to ask your parent or another adult before formatting an SD card that be-longs to someone else. They may want to remove files from the card before you format it.

Using the camera in mass storage mode

If you want to view images and videos you’ve recorded without using the Digital Movie Creator 3.0 software, you can use the camera in mass storage mode. Mass storage means that computers recognize the camera as if it were an external hard drive.

To use the camera in mass storage mode:

1. Attach the camera to the computer using the base and USB cable while pressing and holding the OK button.

2. Go to the Desktop of the computer and double-click on the My Computer icon.

3. You’ll see a list of the computer’s hard drive (usually C:\) and any other mass storage devices currently attached to the computer.

4. Double-click on the “Digital Blue DMC3 Video Device.”

5. The image and video files stored on the camera will be shown.

TV out format

The camera will be in NTSC format when you buy it. NTSC format is frequently used in the US and North America. In the UK, Europe, and other locations, you may want to change the format to PAL. Ask a parent or another adult to help you if you aren’t sure which format to use.

19

Using the Software


Formatting the memory media

The first time you use a new SD card, you need to format it to work with your camera. When you format the SD card, any images, video or other data stored on the card will be erased.

To format an SD card:

1. With the camera turned off, insert the SD card into the camera. (See Inserting the SD card).




5. From the Setup Menu, highlight Format Media using the Down Arrow button and press the OK button to select.

6. A message will display to remind you that all data on the SD card will be lost if you choose to format. Use the Up and Down Arrow buttons to highlight Yes and press the OK button to select.

7. Formatting may take a few moments depending on the size of the card and the data on it. A message telling you that formatting is in progress will display during this time.

8. When the formatting is complete, a message will display. Press the OK button to continue.

18

Note: To change the quality of still images, you’ll need to switch to Snapshot mode by press-

ing the Snapshot button once.

Setting the sleep timer

Your camera will go to sleep if it is not used for 3 minutes.

To change the amount of time before the camera goes to sleep:




4. From the Setup Menu, use the Up and Down Arrow buttons to highlight Sleep Timer and press the OK button to select.

5. Use the Up and Down Arrow buttons to highlight 3 minutes, 10 minutes, or Now and press the OK button to select.

6. If you selected Now, the camera will turn off right away. If you selected 3 or 10 minutes, the camera will wait that long before turning off.

15

Using the Camera


Changing the time and date

To change the time and date:




4. From the Setup Menu, use the Up and Down Arrow buttons to highlight Time/Date and press the OK button to select.

5. The current time and date is displayed. If you want to change the time or date, press the OK button.

6. Use the Right and Left Arrow buttons to highlight the value to change.

7. Use the Up and Down Arrow buttons to change the highlighted value.

8. Press the OK button to set the time and date.

16

Understanding the camera memory

The camera will store images and video to the camera or to an SD card. Your camera has 32MB of on-board memory. If you add an SD card, you’ll be able to store even more!

Inserting the SD card

When you insert an SD card, the camera will store images and video on it until it is full.

To insert an SD card:

1. From the top, carefully pull back cover that protects the SD card slot and TV out connection.

2. Swivel the cover to the right or left to get it out of your way.

3. Insert SD card into the SD card slot as shown below:

4. Swivel the cover back and gently press it into place to secure it.

Note: Your camera can use SD cards 1GB or smaller.

17

Using the Camera


Changing the time and date

To change the time and date:




4. From the Setup Menu, use the Up and Down Arrow buttons to highlight Time/Date and press the OK button to select.

5. The current time and date is displayed. If you want to change the time or date, press the OK button.

6. Use the Right and Left Arrow buttons to highlight the value to change.

7. Use the Up and Down Arrow buttons to change the highlighted value.

8. Press the OK button to set the time and date.

16

Understanding the camera memory

The camera will store images and video to the camera or to an SD card. Your camera has 32MB of on-board memory. If you add an SD card, you’ll be able to store even more!

Inserting the SD card

When you insert an SD card, the camera will store images and video on it until it is full.

To insert an SD card:

1. From the top, carefully pull back cover that protects the SD card slot and TV out connection.

2. Swivel the cover to the right or left to get it out of your way.

3. Insert SD card into the SD card slot as shown below:

4. Swivel the cover back and gently press it into place to secure it.

Note: Your camera can use SD cards 1GB or smaller.

17

Using the Camera


Formatting the memory media

The first time you use a new SD card, you need to format it to work with your camera. When you format the SD card, any images, video or other data stored on the card will be erased.

To format an SD card:

1. With the camera turned off, insert the SD card into the camera. (See Inserting the SD card).




5. From the Setup Menu, highlight Format Media using the Down Arrow button and press the OK button to select.

6. A message will display to remind you that all data on the SD card will be lost if you choose to format. Use the Up and Down Arrow buttons to highlight Yes and press the OK button to select.

7. Formatting may take a few moments depending on the size of the card and the data on it. A message telling you that formatting is in progress will display during this time.

8. When the formatting is complete, a message will display. Press the OK button to continue.

18

Note: To change the quality of still images, you’ll need to switch to Snapshot mode by press-

ing the Snapshot button once.

Setting the sleep timer

Your camera will go to sleep if it is not used for 3 minutes.

To change the amount of time before the camera goes to sleep:




4. From the Setup Menu, use the Up and Down Arrow buttons to highlight Sleep Timer and press the OK button to select.

5. Use the Up and Down Arrow buttons to highlight 3 minutes, 10 minutes, or Now and press the OK button to select.

6. If you selected Now, the camera will turn off right away. If you selected 3 or 10 minutes, the camera will wait that long before turning off.

15

Using the Camera


6. When the item you want to protect is on the Display Screen, press the Up Arrow button to enter the Image File Menu.

7. Highlight Protect using the Down Arrow Button and press the OK button to select.

8. From the protect menu, use the Up and Down Arrow buttons to select Lock and press OK to select.

9. Your video or image is now protected and won’t be deleted if you accidentally select Delete or Delete All.

Note: You’ll need to unprotect videos and images if you want to delete them later.

Choosing the image or video quality

There are two quality settings:

High- Images will look clear, but will take more space than Normal quality images.

Normal - Images take up less space, but aren’t as clear as high quality images.

To change to image quality:


2. Press the Right Arrow button to change the image quality.

3. The icon on the Display Screen will change to indicate your choice.

14

Note: Be sure to ask your parent or another adult before formatting an SD card that be-longs to someone else. They may want to remove files from the card before you format it.

Using the camera in mass storage mode

If you want to view images and videos you’ve recorded without using the Digital Movie Creator 3.0 software, you can use the camera in mass storage mode. Mass storage means that computers recognize the camera as if it were an external hard drive.

To use the camera in mass storage mode:

1. Attach the camera to the computer using the base and USB cable while pressing and holding the OK button.

2. Go to the Desktop of the computer and double-click on the My Computer icon.

3. You’ll see a list of the computer’s hard drive (usually C:\) and any other mass storage devices currently attached to the computer.

4. Double-click on the “Digital Blue DMC3 Video Device.”

5. The image and video files stored on the camera will be shown.

TV out format

The camera will be in NTSC format when you buy it. NTSC format is frequently used in the US and North America. In the UK, Europe, and other locations, you may want to change the format to PAL. Ask a parent or another adult to help you if you aren’t sure which format to use.

19

Using the Software


To change the TV out format:





5. Use the Up and Down Arrow buttons to highlight either NTSC or PAL.

6. Press the OK button to set the TV out format.

Using the camera’s TV out feature

With the TV-out feature, you can use a regular TV to share your videos/pictures with friends & family. You will need the TV-out cable included with your Digital Movie Creator to use this feature. To connect your camera to a TV: 1. Carefully pull back on the top end of the cover and swivel it out of the way.

2. Locate the Audio/Video inputs on your TV.

20

To delete all items on the camera at once:




4. From the Delete Menu, highlight Delete All using the Down Arrow button and press the OK button to select.

5. When asked to confirm that you want to delete all, use the Down Arrow to highlight “Yes.” Press the OK button to select.

6. All items are now deleted.

To protect items from being deleted:



3. Press the Down Arrow button until Playback is highlighted. Press the OK button to select.


5. Use the Right Arrow button to scroll through images and videos until you see the item you want to protect.

Using the Camera

13


To delete the last picture/video you took with the camera:




4. From the Delete Menu, highlight Delete Last using the Down Arrow button and press the OK button to select.


6. The last item you recorded is now deleted.

12

3. If the inputs are marked using red, yellow, and white, match the corresponding end of the cable to the input (i.e., plug the red end of the cable into the red input). If the inputs are not marked with color: plug the yellow end of the cable into the Video input; the white end of the cable into Audio- Left (or “L”) input; and the red end of the cable into the Audio-Right (or “R”) input. If you leave any of these cable ends unconnected, make sure that the metal part does not touch any other metal objects.

4. Connect the black end of the TV out cable to thecamera’s TV out connection.

5. Press the Snapshot or Record button to turn on your camera. You’ll be able to see the Live Preview on your TV screen. You can also access the menus to view the images and videos you have captured. Note: If you’ve plugged your camera into your TV’s secondary or auxiliary input, you may need to change the channel or select the appropriate input from your TV’s menu in order to see the camera’s images. TVs vary, so consult the manual that came with your TV for more details.

21

Using the Camera


Anti-flicker settings

Indoor lighting flickers at different rates around the world. The camera is set to adjust for light that flickers at 60 hertz when you buy it. This prevents you from seeing flickers when you play the video back on a TV or computer.

In the US and North America, light flickers at 60 hertz. In the UK, Europe, and other locations, you may want to change to 50 hertz.

To change the anti-flicker settings:





5. Use the Up and Down Arrow buttons to highlight either 60HZ or 50HZ.

6. Press the OK button to set the anti-flicker.

22 11

Using the Camera

Deleting images and video from the camera

You can delete images and video from the camera in 3 ways: delete one item at a time; delete the last item; or delete all items on the camera at once.

To delete one item at a time





5. Your first image or a still image of the first frame of your first video will be shown on the Display Screen. Use the Right of Left Arrow button to scroll through images and videos until you see the item you want to delete.

6. When the item you want to delete is on the Display Screen, press the Up Arrow button to enter the Image File Menu.

7. Highlight Delete using the Down Arrow Button and press the OK button to select.


9. When your image is deleted, you’ll return to scrolling through images/videos.


Viewing images and movies on the display screen

You can view all the images and videos in your camera’s menu by switching to Playback Mode.






In Playback Mode, you can do the following:

• Press the Right Arrow button to see the next image or video.

• Press the Left Arrow button to see the previous image or video.

• Press the Down Arrow button to see thumbnails of all your images/videos.

• Press the Up Arrow to enter the Image File Menu where you can Delete images/videos or Protect images/videos from ever being deleted.

• Press the OK button to play videos.

Note: To go back to capturing images/video, press the Snapshot or Record button.

10

Making your first movie

It’s fun to make movies using the software that came with your camera!

Shooting a scene with the camera

With your camera connected to your computer you can record movies using the software.To shoot a scene using the software:

1. Place your camera in its base and attach it to your computer (remember that the software MUST be installed FIRST).

2. Double-click on the Digital Blue Digital Movie Creator 3.0 icon on your desktop to start the software. If you don’t have an icon on your desktop, you can click Start>Programs (or All Programs)>Digital Blue Digital Movie Creator 3.0> Digital Movie Creator 3.0 to start the software.

3. When the software starts, you’ll be on the Live Screen where you’ll see what the camera sees on your screen. Make sure the subject you want is in front of the camera.

4. To start recording, press the Record button:

5. When you have captured all the video you want in the scene, press the same button (which is now red.)

Notice that the scene you just created appears in the small window on the screen. Click the Play button to preview it.

23

Using the Software


Rename the scene so you can find it easily

The scene you just recorded is now in the Temporary collection.

1. Open the Collections screen by clicking the Collection button at the top of the screen.

2. Click the title under the scene you just recorded and type in a new name.

3. Press the Enter key on your keyboard to finish renaming your scene.

Save your scene in the Permanent collection

To save the scene, you have to move it from the Temporary collection to the Permanent collection.

1. In the Temporary collection, click on the scene you just created and renamed.

2. In the lower left-area of the of the Collection window, you’ll see your transfer options:

3. Press the One button to move the scene from the Temporary collection to the Permanent collection.

4. Click the Collection screen button to close it.

24 9

Using the Camera

Taking pictures with the camera

To take pictures with your camera, press the Snapshot button (on the top of the camera) to enter Snapshot mode. The first time you press the Snapshot button it will capture one picture immediately. Hold the camera still until the picture has been captured.

Once you’re in Snapshot mode, you can choose to make the Snapshot button take one picture at a time (single), 3 pictures in a row (burst), or wait 10 seconds before taking the pictures (timer).

To change this setting:


2. Use the Left Arrow button to change the icon on the Display Screen.


3. Once you see the icon you want, press the Snapshot button.



Capturing video with the camera

When you turn on the camera, you’re in Live Preview Mode.

To record video:


2. Locate the subject of your video using the Eyepiece or Display Screen.

3. Press the Record button to start recording.

4. When you have captured all the video you want, press the Record button again to stop recording.

5. You can play your video on the camera’s Display Screen (see Viewing images and movies on the Display Screen) or on your computer (by connecting the camera to your com-puter using the camera base and USB cable) with the Digital Movie Creator software.


8

Organize your scenes into a movie

Once you have recorded your scenes, you can use the Storyboard to make your scenes into a movie.

1. Click the Create screen button to open the Create screen.

When the scene opens, it shows the Collections screen and the Storyboard.

2. Click on one of the scenes you created. If you don’t see it, click on the green arrows to see more scenes.

3. Click and drag your scene to the Storyboard.

Repeat this step to add other scenes and images to your video.

4. Once you have added all the scenes you want to your movie, click the Collection screen button to close the Collection screen.

Note: If you decide you want to add more scenes later, you can open the collection screen again at any time.

25

Using the Software


Have fun with your movie

The Create screen has lots of cool ways to make your movie even better!

The Tools menu lets you add scrolling credits, titles, paint, and special movie filters to scenes.

The Special Effects menu has fun animated effects-- like aliens, explosions, and an erupting volcano-- that you can add to your movies.

The Sound Effects menu has fun sounds and music. You can also record your own music or singing as a background music track to play throughout your movie.

Tools menu

Sound Effects menu

Special Effects menu

26

Snapshot Type– Displays the type of capture when the Snapshot button is pressed.


Capture Type– Indicates whether you are taking a snapshot or a video clip.

Snapshot = Video =

When you are playing back your movies you will see these symbols indicating you are viewing a snapshot or playing a video clip.

Snapshot = Video =

Memory Type– Shows which type of memory you currently are using.

Internal = No icon SD Memory Card =

Memory Level– Represents the amount of memory that has been used. There are several stages of memory usage.

Zero Memory Used = Memory Almost Full = Memory Full =

Delete– Flashes as you delete images from the camera.

Counter– Shows the number of images you have captured and how many you can still capture.

7

Using the Camera


Camera Display Screen

The Camera Display screen provides information about your camera settings.

Battery Status Icon– Shows how much battery life the camera has left. When the criti-cally low image appears make sure to change your batteries immediately.

Full = Medium = Low = Critically Low =

Zoom Level– Indicates how much digital magnification you are using to shoot your subject. You can zoom in on your subject with up to four times digital magnification.

Image Quality– Shows whether the camera is filming in Normal or High Quality.

Normal = High =

6

Zoom levelBattery status

Active storage mediumMemory usage

Image qualitySnapshot typeCapture typeN umber of additional images that

can be stored Number of stored images

Preview your movie

While you’re making your movie, you might want to see how it looks before releasing the final cut.

To preview your movie, click the Play button.

27

Using the Software


Share your movie with friends and family

Now that you’ve created your first movie, you can share it with your friends and family.

To show friends and family on your computer:

1. Click the Share button to open the Share screen.

2. Press the Play button to start your movie.

To export your movie:

1. Save your movie by clicking the Save button.

2. Open the collection screen by clicking the Collection screen button.

3. Your movies saved in your Collection will have a movie reel in the upper left-hand corner. Click on the movie you want to export. It will highlight in green.

4. Click the Export button.

5. Choose where you want to save the exported file. The file will save in the My Documents folder unless you change the location.

Now you can e-mail the file (for smaller movies) or burn it to a CD (for larger movies) and share with friends and family.

28

Snapshot Button– Use the Snapshot button to capture still images with your camera.

Built-in Microphone– The microphone automatically records sounds as you capture video clips.

Camera Lens– Make sure to keep the camera lens clean and clear when trying to cap-ture images/video.

Camera Base– The USB cable on the camera’s base connects to your computer. When the camera is in the base and the software is running, you can download pictures, and capture images and video clips in the software.

USB Cable– Connects your camera to your computer, so you can download images to your computer when the camera is in the base.

Eyepiece– Look through the eyepiece to center your subject in the viewfinder.

Display Screen– Use the Display Screen to preview your shots and to view the menu.

Record Button– Use the Record Button to record video with your camera.

Navigation Buttons– Use the Navigation buttons for making selections from the menu or to control zooming while capturing a video. These buttons don’t work when your camera is attached to your computer.

SD Memory Card Slot– The SD Memory Card slot allows you to use your own memory card to store more images and videos on your camera. (SD card not included.)

TV Out– View your videos on the TV screen by using the TV Out cable.

Battery Compartment– Change the batteries by opening the Battery Compartment.

TV Out Cable– Connects your camera to your TV allowing you to view your movies on the screen.

5

Using the Camera


Camera Controls

4

Built-in Microphone

Record Button

USB Cable

Camera Base

Camera Lens

SD Memory Card Slot

TV Out

Battery Compartment

Display Screen

Snapshot Button

Eyepiece

Navigation Buttons

TV Out Cable

To launch the Help file: Click Start > Programs > Digital Blue Digital Movie Creator 3.0 > Digital Movie Creator 3.0 Help

For additional product support visit our website at:www.digitalbluecorp.com and select Customer Service.

If you are still having problems with this product, contact Customer Support at 888-800-0502.

29

Additional Help
