2

300Mbps Ceiling Wireless Access Point

Quick Installation Guide

300Mbps Ceiling Wireless Access Point

Quick Installation Guide1

Hardware and Operation Mode

Interface

Gateway Mode

Access Point Mode

Repeater Mode

AP Mode AP Mode AP Mode

AP Mode Repeater Mode

Router/Switch

Operation Mode

Thank you for purchasing the Ceiling AP. This manual suit for quick installation of indoor 300Mbps 11N wireless AP & High Power Router. This manual will instruct you how to configureand manage indoor 300m 11N wireless AP & High Power Router in right ways.

Introduction

Power LEDWi-fi LED

Data LED

LED

RST: Reset Button,and hold the RESET button for at least 18 seconds when the wifi led is off, and then the AP reboots to its factory default settings. WAN/LAN: The Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. LED: When the Ethernet Port is connect with cable to other device, is Flashing

Gateway

Router/Switch

As belows shows.

Installation Steps

Hareware Conection

Ceiling AP

Setting the AP through Wireless

Router/Switch

PoE Power Supply

Setting the AP using WirelessConnect the Switch or Router’s Ethernet Port to PoE Power Supply’s LAN Port, and connectthe PoE Power Supply’s PoE Port to AP’s WAN port. The computer using wireless to connectthe Ceiling AP (SSID：XD9800,Key:66666666), and then log the 192.168.188.253 to setting the AP using the IE Browser.

Hardware Connection

Setting the Computer

Log in the Web Management

Setting the AP

Test the Wireless Network

Install the AP to the Ceiling

Note:1. Before Install the AP on the Ceiling, you wouldbetter complete the software setting.2. Before the setting of the AP, you would bettercomplete the design of Topology of networkand IP address the devices.

Hardware ConnectionSetting the Computer

Power for Wireless AP

1. Using IEEE 802.3af PoE Switch to supply the Power to the Wireless AP2. Using PoE Power Adapter to supply the Power to the Wireless AP3. Using DC Power Adapter 12V1A to supply the Power to the Wireless AP

Setting the AP through Wires with RJ45 Cable

Ceiling APPOE Power Supply

Setting the AP using WiresConnect the PoE Power Supply’s PoE Port to AP’s LAN port. The computer using wires to connect the PoE’s LAN Port, and then log the 192.168.188.253 to setting the AP using the IE Browser.

Setting the AP through Wireless

same network segment as AP, subnet mask 255.255.255.0192.168.188.X

188

3 (To be continued...)

，the default Passwords is"66666666"

segment as the AP subnet mask 255.255.255.0 As belows shows.

Log in the Web Management

Setting the AP

Setting the AP through Wires with RJ45 Cable

a.Open your web browser, type 192.168.188.253 in the address bar

b.enter the User name/Passwords: preset as admin/admin, then you can found on the label attached to the router, click OK

Enter into the page of WEB software management page, then set ceiling AP as requirement. The default working mode is AP.

XD9800

ZHH

188

9508S

188

Internet Setting: The AP will settingto Gateway Mode;

Wireless Repeater:The AP will settingto Repeater Mode;

Wireless Coverage:The AP will settingto APMode;

System Tools: PING Tools

Advanced Settings

6

AP Deployment

Symptoms TreatmentForget the login user name and passwords

Can’t login AP through WEB management

Forget the AP’s SSID and passwords

Can not got IP Address

No Power indicator

1. Check the AP’s DHCP and make it enable in Gateway mode and WISP mode2. Check the connection between AP and the top networking in AP and Repeater mode

1. If DC Power, check the local power supplier2. If PoE Power, check the PoE adapter and Internet cable

Restore to factory default

Restore to factory default

Trouble Shooting Appendix I Hotel Wireless Solution Appendix 2

1 Pls make sure the PC and AP’s IP Address are in same network segment, can be checked through Ping: PC start--input CMD in Run, then ping 192.168.188.253 2 Login after Restore AP to factory default3 Make sure there isn’t any equipment take IP address of 192.168.188.253 in AP networking4 Check your computer and network cable to avoid any problem, recommend to use unshielded twisted pair 10/100M Ethernet cable.

Topology

Router

AP Mode

AP Mode

Switch

7

PoE Power Supply DataPower

PoE Power Supply Appendix 3

150Mbps Outdoor High Power Wireless Bridge/CPE

WISP mode and AP function can be using at same timeWireless speed up to 150MbpsOutdoor weatherproof protection design12dBi Antenna to build long distance Wi-Fi connectionHigh Power to boost your signal coverage and link Up to 60 meters (200 feet) Power over Ethernet Injector

The PoE power supply of Access Point, line 1.2.3.6 is using transfer the data,and 4.5.7.8 is using transfer the power, 4.5 is “+”, 7.8 is “-”.

4

Setting the AP

Gateway Mode

1. Choose the “Internet Setting”, that means AP will change to Gateway Mode:

Repeater Mode

1. Choose the “Wireless Repeater”, that means AP will change to Repeater Mode:

2. In this mode, the AP’s two Ethernet Port change into WAN & LAN Port:

2. In this mode, the AP can connect to other wireless networks, click the “Scan AP”, the AP will

3. Fill the key of wireless network,and then seeting the wireless of AP

3. WAN Setting: Choose Dail Way, PPPoE/Dynamic IP Support. PPPoE need User Name and User Password

NOTE: In the mode, the DHCP Server is enable by default, the computer can get the IPaddress from AP.

5. Click the Apply the System will reboot.

5. Click the Apply the System will reboot.

4. Wireless: setting the Wireless Network, such as SSID and Key of the netowrk. - SSID : the name of wireless network

here will show details of wireless networks nearby- Authentication and Encryption: WPA2-PSK, AES is default 4. Wireless: setting the Wireless Network, such as SSID and Key of the netowrk.

- SSID : the name of wireless network

here will show details of wireless networks nearby- Authentication and Encryption: WPA2-PSK, AES is default

Test the Wireless Network

computer wireless connection as local connection settings mentioned above.

wireless network’s performance.

5

NOTE: In the mode, the DHCP Server is disable by default, the computer can get the IPaddress from core router.

3. Click the Apply the System will reboot.

2. Wireless: setting the Wireless Network, such as SSID and Key of the netowrk. - SSID : the name of wireless network

here will show details of wireless networks nearby- Authentication and Encryption: WPA2-PSK, AES is default

AP Mode

1. Choose the “Wireless Coverage”, that means AP will change to AP Mode:

Advances Setting

Choose the “Advances Setting”, you can set Firewall and Management function of AP:

IP/Port/MAC/URL Filtering: This feature is turned on, the router will be in accordance

rules for [refuse], the router will refuse to forward data in accordance with the

n accordance with the conditions Backup: Restore: Reset Default: Restore the factory default settings, please press this button Reboot: Device will restartRouter, DDNS, QoS, User Logs, Upgrade Firmaware are also supports