PRODUCTNEWS - az · 2011-10-17 · 423 Hardness Tester Rockwell Type Durotwin DT10-IS-D Rockwell/Super Rockwell Type Durotwin DFlat table Ø 63 mm, V-anvil Ø 41 mm, Rockwell/Super

Hardness Tester Rockwell / Super Rockwell / Brinell Type Durotwin PlusDetailed information on page 421.

PRODUCTNEWS

Härteprüfgeräte

Pages 428–430

Hardness Tester Micro-Vickers

Hardness Tester Vickers

Page 431

Hardness Tester Vickers + Brinell

Pages 432–433

Portable Hardness Tester Shore

Pages 434–435

Hardness Tester Rockwell / Super Rockwell /

Brinell Pages 422–427

Portable Hardness Testing Devices

Pages 436–437

421

Testing Equipements and Seismometer

422

Hardness Tester Rockwell/Super Rockwell Type Durotwin Rockwell/Super Rockwell/Brinell Type Durotwin Plus

Robust and user-friendly manual Rockwell, Super Rockwell and Brinell hardness testers.•

Series 963

963-102 R 963-103

Standard accessories

No. Designation19BAA072 Diamond indenter56AAJ087 Carbide indenter 1/16” – Flat table Ø 63 mm – V-anvil Ø 41 mm,

groove width 25 mm – Dust protection cover – Hardness testing block

60-65 HRC – Hardness testing block

60-64 HR30N – Level

Aditional standard accessories Durotwin Plus

No. Designation19BAA279 Carbide indenter Ø 2,5 mm – Hardness testing block

350 HBW 2,5/187,5

Optional accessories

No. Designation19BAA072MPA Diamond indenter

(incl. MPA certificate)56AAJ082 Carbide indenter 1/8”56AAF540MPA Carbide ball 1/16”56AAG233MPA Carbide ball 1/8”075202 Round table Ø 200 mm810-040 V-anvil Ø 40 mm,

groove width 30 mm, 120°810-041 V-anvil Ø 40 mm,


groove width 8 mm, 120°810-030 Point anvil (diamond tipped

for Super-Rockwell)810-043 Point anvil (Ø 12 mm)810-044 Point anvil (Ø 5,5 mm)

Additional optional accessories Durotwin Plus

No. Designation19BAA280 Carbide indenter Ø 5 mm19BAA162 Replacement carbide ball

indenter Ø 5 mm (1 pce.)19BAA318D Stand microscope 40 x19BAA319D Stand microscope 100 x56AAE497 Replacement carbide ball

indenter Ø 2,5 mm (5 pcs.)56AAE498D Hardness testing block

350 HBW 2,5/187,5 (incl. MPA certificate)

Request our detailed brochure!

Model Durotwin Durotwin PlusNo. 963-102 R 963-103Rockwell Scales A – D – C

(Diamond indenter)Scales A – D – C

(Diamond indenter)Scales F – B – G

(1/16” Carbide ball indenter)Scales F – B – G

(1/16” Carbide ball indenter)Scales H – E – K*


(1/8” Carbide ball indenter)Super Rockwell (Scales N, T)

Scales 15N – 30N – 45N (Diamond indenter)


Scales 15T – 30T – 45T (1/16” Carbide ball indenter)


Brinell** – Scale HBW5/125* (5 mm Carbide ball)

– Scale HBW2,5/187,5 (2,5 mm Carbide ball)



* Accessories (optional)

No. 963-103No. 963-102 R

Rockwell Super Rockwell (Scales N, T) Brinell**Preliminary test force (N) 98,07 29,42 98,07Test force (N) 588,4; 980,7; 1471 147,1; 294,2; 441,3 306,5; 612,9; 1226; 1839Graduation 0,5 HR 1 HR –Display Analogue Stand microscope*Mass 44 kg 48 kg * Accessories (optional) ** Indentations must be measured using a measuring microscope (not supplied with the instrument).

423

Hardness Tester Rockwell Type Durotwin DT10-IS-D Rockwell/Super Rockwell Type Durotwin D Rockwell/Super Rockwell/Brinell Type Durotwin Plus D

Sturdy and simple to operate Rockwell, Super Rockwell and Brinell hardness testers.•Hardness Tester according to DIN EN ISO 6508-2 and DIN EN ISO 6506-2.•

963-104-50D

Standard accessories Durotwin DT10-IS-D

No. Designation19BAA072 Diamond indenter

Flat table Ø 63 mm, V-anvil Ø 41 mm, groove width 25 mm, dust protection cover, hardness testing block 60-65 HRC, level

Optional accessories Durotwin DT10-IS-D

No. Designation56AAJ087 Carbide indenter 1/16”56AAF540MPA Replacement carbide ball

indenter 1/16” (1 pce.)56AAJ082 Carbide indenter 1/8” 56AAF540MPA Replacement carbide ball

indenter 1/8” (1 pce.)075202 Round table Ø 200 mm

Standard accessories Durotwin D

No. Designation19BAA072 Diamond indenter56AAJ087 Carbide indenter 1/16”

Flat table Ø 63 mm, V-anvil Ø 41 mm, groove width 25 mm, dust protection cover, hardness testing block 60-65 HRC, hardness testing block 60-64 HR30N, level

Optional accessories Durotwin D

No. Designation56AAF540MPA Replacement carbide ball

indenter 1/16” (1 pce.)56AAJ082 Carbide indenter 1/8” 56AAG233MPA Replacement carbide ball

indenter 1/8” (1 pce.)075202 Round table Ø 200 mm

Standard accessories Durotwin Plus D

No. Designation19BAA072 Diamond indenter56AAJ087 Carbide indenter 1/16”19BAA279 Carbide indenter Ø 2,5 mm

Flat table Ø 63 mm, V-anvil Ø 41 mm, groove width 25 mm, dust protection cover, hardness testing block 60-65 HRC, hardness testing block 60-64 HR30N, hardness testing block 350 HBW 2,5/187,5, levelOptional accessories Durot win Plus D

No. Designation56AAF540MPA Replacement carbide ball

indenter 1/16” (1 pce.)56AAJ082 Carbide indenter 1/8” 56AAG233MPA Replacement carbide ball

indenter 1/8” (1 pce.)19BAA280 Carbide indenter

Ø 5 mm (1 pce.)19BAA162 Replacement carbide ball

indenter Ø 5 mm (1 pce.)19BAA318D Stand microscope 40 x19BAA319D Stand microscope 100 x075202 Round table Ø 200 mm

Optional accessories for all Durotwin devices

No. Designation810-040 V-anvil Ø 40 mm,





Series 963

Model Durotwin DT10-IS-D Durotwin D Durotwin Plus DNo. 963-104-50D 963-102-50D 963-103-50DRockwell Scales A – D – C



(Diamond indenter)Scales F – B – G*






(1/8” Carbide ball indenter)Super Rockwell(Scales N, T)





Brinell** Scale HBW5/125* (5 mm Carbide ball)

Scale HBW2,5/187,5 (2,5 mm Carbide ball)Scale HBW2,5/62,5

(2,5 mm Carbide ball)Scale HBW2,5/31,25 (2,5 mm Carbide ball)

* Accessories (optional)

No. 963-103-50DNo. 963-102-50DNo. 963-104-50D

Rockwell Super Rockwell (Scales N, T) Brinell**Preliminary test force (N) 98,07 29,42 98,07Test force (N) 588,4; 980,7; 1471 147,1; 294,2; 441,3 306,5; 612,9; 1226; 1839Graduation 0,1 HR 0,1 HR –Display Digital Stand microscope*Mass 44 kg 48 kg * Accessories (optional) ** Indentations must be measured using a measuring microscope (not supplied with the instrument).

424

Series 810

Hardness testing systems Rockwell / Super Rockwell / Brinell type Wizhard

Hardness testing systems according to DIN EN ISO 6508-2 and DIN EN ISO 6506-2. •Varying Rockwell, Rockwell Superficial (Scales N, T) and Brinell test forces.•Electronic real-time load control for precise adjustment. This avoids the possibility of applying •excessive test forces.Auto-stop elevating table with automatic application of preliminary test force.•Beak-shaped extension arm for improved access to internal and external surfaces.•Graphic illustration of statistical results and the widest range of key statistical values.•Evaluation function OK/Not OK.•Automatic selection of test force: •The required hardness test is defined in advance and the test force automatically selected.

Operation via touch screen (HR–521 / HR–522 / HR–523)

Operation via control unit (HR–511)


810-208D 810-202D

810-204D

425

Hardness testing systems Rockwell / Super Rockwell / Brinell type Wizhard

Intender


No. Designation19BAA073 Diamond indenter,

min. hole-Ø 40 mm19BAA074 Steel ball indenter 1/16”19BAA082 Replacement steel ball 1/16”

(10 balls)810-039 Flat table Ø 64 mm810-040 V-anvil Ø 40 mm,

groove width 30 mm, 120°19BAA123 Hardness testing block

30-35 HRC19BAA125 Hardness testing block


90-95 HRB19BAA128 Hardness testing block

64-69 HR30N19BAA129 Hardness testing block

70-79 HR30T19BAA517 Dust protection cover19BAA098 Level



(incl. MPA certificate)19BAA292MPA Diamond indenter,

min. hole-Ø 22 mm19BAA075 Steel ball indenter 1/8”810-037 Round table Ø 180 mm810-038 Round table Ø 250 mm810-040 V-anvil Ø 40 mm,



groove width 8 mm, 120°810-029 V-anvil length 400 mm,



Optional accessory for Brinell hardness testing

No. Designation19BAA277 Carbide ball indenter

Ø 1 mm19BAA279 Carbide ball indenter

Ø 2,5 mm19BAA280 Carbide ball indenter

Ø 5 mm19BAA284 Carbide ball indenter

Ø 10 mm19BAA281 Replacement carbide ball

indenter Ø 1 mm (1 pce.)19BAA283 Replacement carbide ball

indenter Ø 2,5 mm (1 pce.)19BAA162 Replacement carbide ball


indenter Ø 10 mm (1 pce.)19BAA318 D Stand microscope 40 x19BAA319 D Stand microscope 100 x

Further certified hardness comparison plates on request.

Model HR–511 HR–521 / HR–522 / HR–523Control unit operation –Via touch screen –Test force controlData offsetMeasured value compensation for cylindrical and spherical surfaces

–

Conversion to other hardness scales – HV, HK, HBS, tensile strength, HRA, HRB, HRC, HRD, HRF, HRG, HR15T, HR30T, HR45T,

HR15N, HR30N, HR45N, HS, HB (HBS)Statistical functions Number of values, max., min., average value,

range, upper limit, lower limit, standard deviation, number of OK/Not OK evaluations

(via data output only) storage of 1024 values

Number of values, max., min., average value, range, upper limit, lower limit, standard

deviation,number of OK/Not OK evaluations histogram,

_X-R control card

storage and editing of 1024 valuesTolerance evaluation

Model HR–511 HR–521 HR–522 HR–523No. 810-208D 810-202D 810-203D 810-204DPreliminary test force (N) 29,42; 98,07Test force

Rockwell (N) 588,4; 980,7; 1471Super Rockwell (N)(Scales N, T)

147,1; 294,2; 441,3

Brinell* (ball-Ø/kg)

HBW 2,5/187,5 HBW 1/10; HBW 1/30; HBW 2,5/6,25; HBW 2,5/15,625; HBW 2,5/31,25;

HBW 2,5/62,5; HBW 2,5/187,5; HBW 5/25; HBW 5/62,5; HBW 5/125;

HBW 10/100Load process Automatic (load, dwell, unload)Display unit Control unit LCD Touch-ScreenTest load selection via keyboard via Touch-ScreenEffective period 0 to 120 sec (in 1 second increments)Max. workpiece size Height: 250 mm, Depth: 150 mm from center of indenterTable movement manual fully automaticData output RS-232 C / DIGIMATIC / CentronicsPower supply 230 V, 50/60 HzDimensions (W x D x H) Main unit 250 x 670 x 605 mmMass Main unit approx. 60 kg* Indentations must be measured using a measuring microscope (not supplied with the instrument).

426

Series 810Analogue and digital types.


No. Designation19BAA072 Diamond indenter19BAA074 Steel ball indenter 1/16”810-039 Flat table Ø 64 mm19BAA123 Hardness testing block



90-95 HRB19BAA111 Dust protection cover



(incl. MPA certificate)264-504-5 D Printer DP-1 VR810-037 Round table Ø 180 mm810-038 Round table Ø 250 mm810-040 V-anvil Ø 40 mm,




groove width 50 mm, 120°810-043 Point anvil (Ø 12 mm)810-044 Point anvil (Ø 5,5 mm)810-026 Special table for Jominy-Test810-027 Variable support arm

(length 250 mm)


Consumables

No. Designation19BAA097 Lamp (10 pcs.)

810-218D810-200D 810-201D

Hardness Tester RockwellAnalog:

Analog standard models with automatic loading, duration and disengagement of additional •test force.Test methods HRA, HRC, HRD (diamond cone) HRF, HRB, HRG (steel ball • 1/16”).Automatic zero positioning of the analog dial indicator when applying test forces with the •spindle wheel.

Digital:Hardness Tester according to DIN EN ISO 6508-2. •Digital standard model with automatic loading, duration and disengagement of additional test •force.Large LED display with tolerance evaluation function.•


Model AR–10 AR–20 ARK–600No. 810-200D 810-201D 810-218DVersion RockwellPreliminary test force (N) 98,07Test force (N) 588,4; 980,7; 1471Table movement manualPreliminary test force Manual adjustmentLoad process Additional test force: automatic (loading, duration, unloading)Effective period adjustableDisplay Analog dial LED (4 digit)Resolution/ Graduation 0,5 0,1Max. workpiece height 165 mm 140 mmMax. workpiece depth 115 mm

(from the center of the indenter shaft)

122 mm (from the center of the

indenter shaft)

122 mm (from the center of the

indenter shaft)Data output – RS-232 C / DIGIMATICDimensions (W x D x H) 215 x 445 x 682 mm 210 x 486 x 680 mm 210 x 486 x 680 mmMass 38 kg 40 kg 40 kg

427

Series 810Digital type.

810-257D


No. Designation19BAA073 Diamond indenter19BAA074 Steel ball indenter 1/16”810-039 Flat table Ø 64 mm19BAA123 Hardness testing block



90-95 HRB19BAA128 Hardness testing block

64-69 HR30N19BAA129 Hardness testing block

74-79 HR30T19BAA112 Dust protection cover



(incl. MPA certificate)264-504-5 D Printer DP-1 VR810-037 Round table Ø 180 mm810-038 Round table Ø 250 mm810-040 V-anvil Ø 40 mm,




groove width 50 mm, 120°810-030 Point anvil

(diamond tipped for Super-Rockwell)

810-043 Point anvil (Ø 12 mm)810-044 Point anvil (Ø 5,5 mm)810–026 Special table for Jominy-Test810–027 Variable support arm

(length 250 mm)


Consumables

No. Designation19BAA097 Lamp (10 pcs.)

Hardness Tester Rockwell/Super RockwellHardness Tester according to DIN EN ISO 6508-2.•Digital standard models with automatic loading, duration and disengagement of additional •test force.Tests according to Rockwell and Super Rockwell (Scale N, T).•Large LED display with tolerance evaluation function.•

Model ATK–600No. 810-257DVersion Rockwell / Super RockwellPreliminary test force (N) 98,07 / 29,42Test force (N) 588,4; 980,7; 1471; 147,1; 294,2; 441,3Table movement manualLoad process automatic (loading, duration, unloading)Effective period adjustableDisplay LED (4 digit)Resolution Rockwell / Super Rockwell

0,1 / 0,2

Max. workpiece height 140 mmMax. workpiece depth 122 mm

(from center of the indenter ball)Data output RS-232 C / DIGIMATIC / CentronicsDimensions (W x D x H) 210 x 486 x 720 mmMass 42 kg

428

Hardness Tester Micro-Vickers Type HM-100Hardness tester according to DIN EN ISO 6507 and JIS B7725.•Micro-Vickers hardness tester with Vickers tests from HV 0.01 – HV 1.•Up to 3 objectives can be connected that can all be used for indent measurement (except •HM-101).A Knoop indenter can also be connected.•Manual lens system switch.•


No. Designation810-617 10 x Objective810-619 50 x Objective19BAA058 Diamond indenter810-011 XY table (HM-101)810-074 XY table (HM-112)810-016 Vice,

max. 45 mm groove width10BAA445 Camera-Adapter for

CCD-camera19BAA109 Dust protection cover19BAA007 Hardness testing block

(700 HV0.3) – Vickers hardness testing table

(HM-101) – Halogen lamp (6 V/20 W)

built-in (all models) – Level



(incl. MPA certificate)810-616 5 x Objective*810-617 10 x Objective*810-618 20 x Objective*810-619 50 x Objective*810-620 100 x Objective** Installation by Mitutoyo

810-012 XY table 50 x 50 mm, Table dimensions 125 x 125 mm

810-017 Vice, max. 100 mm groove width

810-013 Thin plate holder, (max. specimen thickness 5 mm)

810-014 Wire holder horizontal, (max. Ø 3,2 mm)

810-015 Wire holder vertical, (max. Ø 3,2 mm)

810-018 Rotary table810-019 Special vice, swiveling

(horizontal / vertical)810-020 Universal specimen holder810-085 Specimen holder, adjustable,

for thin plates

Further certified hardness comparison plates on request.Software with camera for measuring and evaluation on request.

810-126D810-124D

Series 810

Test force HM-101 HM-112HV HV0.01 HV0.025 HV0.05 HV0.1gf 10 25 50 100

mN 98,07 245,2 490,3 980,7HV HV0.2 HV0.3 HV0.5 HV1gf 200 300 500 1000

mN 1961 2942 4903 9807

Model HM-112“Touch screen” operationReading of diagonals D1 and D2Reading of hardness valuesReading of XY stage positionTest conditions such as test force or effective periodTolerance evaluationMeasured value compensation when testing cylindrical or spherical surfacesControl of automatic lens system switch –Conversion into other hardness scales Soft: HV, HK, HBS, tensile strength, HRA, HRB, HRF, HRG, HR15T, HR30T, HR45T

Hard: HV, HK, HS, HBS, tensile strength, HRA, HRC, HRD, HR15N, HR30N, HR45NStatistical functions Number of values, max., min., average value, range, upper limit, lower limit,

standard deviation, number of OK/Not OK evaluations, storage and editing of 256 values

Model HM-101 HM-112No. 810-124D 810-126DLoading process automatic (loading, duration, unloading)Effective period 5–30 s (in 5 sec increments) 5–90 s (in 1 sec increments)Lens system 10 x; 50 x 10 x; 50 xLens system switch manualMagnification 100 x; 500 x 100 x; 500 xMin. resolution 0,2 µm (50 x Objective) 0,01 µmReading of hardness values at Vickers table via “Touch Screen”XY-stage dimensions 100 x 100 mmTraveling range 25 x 25 mmGraduation 0,01 mm 0,001 mm (Digital)Max. workpiece size height 95 mm; depth 150 mm (from center of the indenter shaft)Observation by micrometer eyepieceData output – RS-232 C / DIGIMATIC / CentronicsDimensions (W x H x D) Main unit 410 x 600 x 590 mmMass Main unit 42 kg

429

Series 810

Hardness Testers Micro-Vickers Type HM-200Hardness testers according to DIN EN ISO 6507 and JIS B 7725.•Multifunctional.•Built-in LCD color monitor with touch screen operation.•Standard equipped with motorized and manual lens changer.•These devices operate without “deadweight” by simple electromagnetic test force application.•Lens changer may be equipped with up to 4 lenses and up to 2 indenters (Knoop/Vickers).•Lenses with extremely large working distance.•Camera port as standard.•Test forces from HV 0,00005 to HV 2 (depending on the type of device).•Standard accessories

No. Designation19BAA407 10 x Eyepiece19BAA440 100 x Objective (HM-221 only)19BAA439 50 x Objective810-617 10 x Objective19BAA058 Diamond indenter Vickers

(HM-211)19BAA059 Diamond indenter Vickers

(HM-221)810-074 XY table digital810-016 Vice, max. 51 mm groove width938905 Optical green filter11BAA961 Eye cup for eyepiece19BAA522 Camera-Adapter02DEA471 Dust protection cover19BAA007 Hardness testing block

(700 HV0,3)938882 2 Batteries (SR-44)19BAA207 Halogen lamp (12 V/50 W)

810-352D

810-353D with camera and monitor (optional accessories)

Lenses and indenters •Max. 4 lenses and max. 2 indenters (Knoop and Vickers)

Servo powered and manual lens system •switch as standard


Test force HM-211 HM-221HV HV0.00005 HV0.0001 HV0.0002 HV0.0003 HV0.0005

–

gf 0.05 0.1 0.2 0.3 0.5mN 0,4903 0,9807 1,961 2,942 4,903HV HV0.001 HV0.002 HV0.003 HV0.005gf 1 2 3 5

mN 9,807 19,61 29,42 49,03HV HV0.01 HV0.02 HV0.03 HV0.05 HV0.1gf 10 20 30 50 100

mN 98,07 196,1 294,2 490,3 980,7HV HV0.2 HV0.3 HV0.5 HV1gf 200 300 500 1000

mN 1961 2942 4903 9807HV HV2

–gf 2000mN 19610

A freely definable test force may be set.

430

Hardness Testers Micro-Vickers HM-200

Touch panel functions and display


No. Designation810-616* 5 x Objective W.D. 13,5 mm810-618* 20 x Objective W.D. 1,8 mm19BAA440* 100 x Objective W.D. 2,5 mm19BAA061** Knoop-indenter for HM-21119BAA062** Knoop-indenter for HM-221810-017 Vice,

max. 100 mm groove width810-013 Thin plate holder,

max. specimen thickness 5 mm810-014 Wire holder horizontal

Ø 0,4–3 mm810-015 Wire/ball holder vertical

Ø 0,4–3 mm810-019 Special vice, swiveling

groove width 37 mm, Horizontal: ± 25°, Vertical: ± 15°

810-020 Universal specimen holder up to 30 mm

810-018 Rotary table 1° scale graduation

810-084 Rotary universal specimen holder max. workpiece height 30 mm max. workpiece Ø 38 mm

810-085 Adjustable thin plate holder, max. sheet metal thickness 3 mm max. sheet metal thickness 56 mm

264-504-5 D Statistical printer DP-1 VR936937 Signal line for DP-1 VR

* Installation through Mitutoyo engineer necessary.

** Device with test certificate for Knoop only available as option.

Further certified hardness comparison plates on request!

Optional accessories for expansion and optimization


No. Designation810-354 D CCD video camera

with external screen810-355-1 CCD video camera for

connection to a computer and VL-Pak evaluation software

810-356 D* Automatic XY table810-357* Auto-focus unit to enhance

the XY table

* based on 810-355-1

Model HM-211 HM-221No. 810-352 D 810-353 DLoading process automatic (loading, duration, unloading)Selection of test force via touch screenTest force mechanism Electromagnetic force applicationEffective period 1-999 s in 1-second incrementsTurret head mechanism automatic or manualMax number of lenses 4Max. number of indenters 2 (1 pce. standard / 1 pce. option)Lens system (standard) 10 x; 50 x 10 x; 50 x; 100 xEyepiece (standard) 10 xWorking distance, lens 10 x = 5,6 mm / 50 x = 1,1 mm / 100 x = 2,5 mmXY-stage dimensions 100 x 100 mm Traveling range 25 x 25 mmMin. resolution, table 1 µm (built-in micrometer)Max. workpiece size height 133 mm; depth 160 mm (from center of indenter)Max. workpiece weight 20 kg incl. table and viceDisplay LCD Touch PanelData output RS-232 C, Parallel (Centronics), DIGIMATICDimensions (W x H x D) Main unit 400 x 600 x 640 mmMass Main unit 43 kg

Hardness value conversion: SAE-table, ASTM table, DIN 50 150, BS i860, MitutoyoDiagonals D1 / D2: max. 5 digitsA Resolution: for lens $ 50 x 0,01 µm / for lens , 50 x 0,1 µmFurther displayed data / values

Hardness value max. 4 digits, min. 0,1 HV/HK•Test force •Indenter (HV/HK) •Duration of load / effective period / unload•Tolerance evaluation –NG / GO / +NG •X/Y stage position •Measured value compensation for cylindrical and spherical surface measurements •Measured value compensation general (offset) •Turret head position•Conversion to other hardness scales•Statistical functions•

Display languages: German, Japanese, English, French, Italian, Spanish

431

Series 810


No. Designation810-064 10 x Objective19BAA060 Diamond indenter810-039 Flat table Ø 64 mm810-040 V-anvil Ø 40 mm,


groove width 6 mm, 90°19BAA219 D Lamp built-in19BAA110 Dust protection cover19BAA016 Hardness testing block

(720 HV 10) – Vickers table – Level



(incl. MPA certificate)810-037 Round table Ø 180 mm810-038 Round table Ø 250 mm810-017 Vice

(max. groove width 100 mm)

Further hardness testing blocks and upgrade kits for Brinell testing on request.

810-160 D

Hardness Tester VICKERS Type AVKThe basic Vickers hardness testing machine – cost-efficient and simple!•Measurement of diagonals using an analog measuring microscope and reading of hardness •values from the external Vickers chart.


Model AVK–C0No. 810-160 DTest force (N) 9,807; 49,03; 98,07; 196,1; 294,2; 490,3Loading process automatic (loading, duration, unloading)Effective period 5 to 30 sec (in 5 sec increments)Objective 10 xMagnification 100 xMin. resolution 1 µmMax. workpiece size height 205 mm / depth 165 mm (from center of the indenter shaft)Observation by micrometer eyepiecePower supply 230 V, 50 HzDimensions (W x H x D) 200 x 705 x 600 mmMass 50 kg

432

Hardness Tester VICKERS + Brinell Type HVHardness Tester according to DIN EN ISO 6507. •The motive revolver enables switchovers between penetrator and objectives via the display •unit.The display unit is separate from the test machine itself to allow ergonomic and user-friendly •operation.All major functions can be performed using the simple, intuitive touch screen.•Use of 2 objectives for measurement.•Simple and rapid statistical analysis of measuring results.•

810-163 D HV–112 / HV–114


No. Designation810-617 10 x Objective810-618 20 x Objective19BAA060 Diamond indenter810-039 Flat table Ø 64 mm810-040 V-anvil Ø 40 mm,


groove width 6 mm, 90°19BAA219 Halogen lamp

(6 V/20 W), built-in19BAA016 Hardness testing block

(720 HV 10)19BAA110 Dust protection cover



(incl. MPA certificate)810-616 5 x Objective*810-619 50 x Objective** Installation by Mitutoyo

19BAA063 Knoop diamond indenter810-012 XY table 50 x 50 mm,

Table dimensions 125 x 125 mm



810-037 Round table Ø 180 mm810-038 Round table Ø 250 mm19BAA445 Camera-Adapter for

CCD-camera

Brinell hardness testing: Special inquiry

Further certified hardness comparison plates on request.Devices with external monitor for measuring diagonals: HV-113 and HV-115 on request.Software with camera for measuring and evaluation on request.

Series 810

Model HV–112 / HV–114“Touch screen” operationReading of diagonals D1 and D2Reading of hardness valuesTest conditions such as test force or effective periodTolerance evaluationMeasurement value compensation when measuring cylindrical or spherical surfacesAutomatic lens changer controlConversion into other hardness scales Soft: HV, HK, tensile strength, HRA, HRB, HRF, HRG, HR15T, HR30T, HR45T

Hard: HV, HK, HS, HBS, tensile strength, HRA, HRC, HRD, HR15N, HR30N, HR45NStatistical functions Number of values, max., min., average value, range, upper limit, lower limit,

standard deviation, number of OK/Not OK evaluations, storage and editing of 256 values

Model HV–112 HV–114No. 810-163 D 810-165 DTest force (N) 1,961; 2,942; 4,903; 9,807; 24,51; 49,03;

98,07; 196,19,807; 19,61; 29,42; 49,03; 98,07;

196,1; 294,2; 490,3Loading process automatic (loading, duration, unloading)Effective period 5 – 99 sec (in 1 sec increments)Lens system 20 x, 10 xLens system switch motor drivenMagnification 200 x, 100 xMin. resolution 0,1 µmMax. workpiece size height 210 mm / depth 170 mm (from center of the indenter shaft)Observation by Micrometer eyepiecerDisplay LCD Touch screenData output RS-232 C / Centronics / DIGIMATICDimensions (W x D x H) Main unit: 245 x 515 x 840 mmMass Main unit: 57 kg

433

Hardness Tester Brinell ABK–1ABK-1 is a hardness testing machine that is easy to operate and extremely accurate. •It is used for testing raw materials, cast/forged parts and special steel.A large indentation can create a smooth surface even when measuring rough surfaces.•The handle for vertical table movement uses an axial thrust bearing to ensure smooth and •even upward and downward movements.The distribution of the weight ensures that test forces of between 4903 N (500 kgf) and •29420 N (3000 kgf) can be applied. Two different sized carbide penetrators (10 mm and 5 mm) can be used, depending on the sample.

Series 810

810-265-1


No. Designation– Weight for 4903 N (500 Kgf)

(1 pce.)– Weight for 2452 N (250 Kgf)

(2 pairs)– Weight for 9807 N (1000 Kgf)

(2 pairs)– Carbide ball Ø 5 mm (1 pce.)– Carbide ball Ø 10 mm (1 pce.)– Flat table Ø 68 mm (1 pce.)– V-anvil (1 pce.)– Microscope 20 x (1 pce.)– Dust protection cover– Brinell hardness table


No. Designation19BAA162 Replacement carbide ball


indenter Ø 10 mm (1 pce.)19BAA166 D Hardness testing block

200 HB


Model ABK–1No. 810-265-1Test force N 4903, 7355, 9807, 14710, 19614, 24517, 29420

Kgf 500, 750, 1000, 1500, 2000, 2500, 3000Change of test force manual (weight exchange)Load process manual (load, dwell, unload)Max. workpiece height 200 mmMax. workpiece depth 155 mmDimensions (W x D x H) 430 x 510 x 1100 mmMass approx. 180 kg

434

Portable Hardness Tester ShoreTesting of rubber, elastomers and plastics.•

Series 811Analog type

Long leg and compact design •Shore hardness “A” and “D”•

811-331 811-335-01

Shore A

Hardness scale range: 0–100 Shore AMeasuring range: 10– 90 Shore A

Shore DHardness scale range: 0–100 Shore DMeasuring range: 20– 90 Shore D


No. Designation811-019 Measuring stand for 811-331811-012 Measuring stand for 811-333811-013 Measuring stand for 811-335-01811-014 Measuring stand for 811-337-0164AAA964 Test probe set (rubber)

Hardness 30, 60, 90 Shore “A”64AAA590 Test probe set (rubber)

Hardness 20, 40, 80 Shore “D”

Additional optional accessory on request.

64AAA964

Measuring stand for different applications

For the hardness measurement.•To the examination of the spring action of •the master unit.

One Unit – 3 applications

1) Hardness testing

2) Testing the spring action

3) Manual measurement

Long leg design Compact designNo. 811-331 811-333 811-335-01 811-337-01Materials to be tested regular rubber

soft plastichard rubber hard plastic

regular rubber soft plastic

hard rubber hard plastic

Shore hardness A D A DStandard JIS K 7215, JIS K 6253, ISO 868, ISO 7619, ASTM D 2240Tip form Cut cone Cone Cut cone ConeTip radius – 0,1 ± 0,012 mm – 0,1 ± 0,012 mmTip diameter Ø 0,79 mm – Ø 0,79 mm –Graduation 1 degree / dial with maximum pointerPressure plan form Ø 18 mm Ø 18 mmMass 320 g 300 g

435

Portable Hardness Tester ShoreTesting of rubber, elastomers and plastics.•

Series 811Digital type

Long leg and compact design •Shore hardness “A” and “D” •

811-332 811-338-01

Shore A

Hardness scale range: 0–100 Shore AMeasuring range: 10– 90 Shore A

Shore DHardness scale range: 0–100 Shore DMeasuring range: 20– 90 Shore D


No. Designation905693 Signal cable (1 m)905694 Signal cable (2 m)19BAA406 Data processor (printer)811-019 Measuring stand for 811-332811-012 Measuring stand for 811-334811-013 Measuring stand for 811-336-01811-014 Measuring stand for 811-338-0164AAA964 Test probe set (rubber)

Hardness 30, 60, 90 Shore “A”64AAA590 Test probe set (rubber)

Hardness 20, 40, 80 Shore “D”

Additional optional accessory on request.

64AAA964Request our detailed brochure!

Long leg design Compact designNo. 811-332 811-334 811-336-01 811-338-01Materials to be tested regular rubber

soft plastichard rubber hard plastic

regular rubber soft plastic

hard rubber hard plastic

Shore hardness A D A DStandard JIS K 7215, JIS K 6253, ISO 868, ISO 7619, ASTM D 2240Tip form Cut cone Cone Cut cone ConeResolution 0,5 degree / Digital display with HOLD function and “DIGIMATIC” outputPressure plan form Ø 18 mm Ø 18 mmMass 310 g approx. 290 g

Functions Series 811Data outputON / OFFDATA / HOLDZERO setting

436

“HARDMATIC” HH–411 Portable Hardness Testing DevicesThe “HARDMATIC” HH–411 is a light-weight portable hardness testing instrument for metal •workpieces.It works on the rebound hardness principle (standardised according to ASTM A 956). •Measurement is conducted with hardness value L (Leeb-value), however, conversion to any •desired hardness scale can be performed.In addition the display automatically shows OK/NG with the tolerance function set and selected.•Memory function for 1800 measured values.•Automatic measuring direction angle-compensation of the given angle.•

Series 810Digital type

810-298

Sample application

Surface roughness and minimum depth/mass of workpiece

1) Surface The workpiece surface should be Ra 2 µm or less.

2) Minimum depth/mass Minimum depth has to be at least 5 mm, minimum mass at least 5 kg; workpieces with other characteristic may be measured after certain preparation (i.e. mounting on granite plate).


No. Designation810-287 Main unit (impact device)19BAA450-01 Valuation unit19BAA457 Carbide ball indenter19BAA451 Support ring Ø 22 mm – Battery (2 pcs.)19BAA258 Cleaning brush19BAA452 Support ring Ø 14 mm19BAA265 Hardness testing block

HLD 800 – Plastic case19BAA460 Detector cable


Model HH–411No. 810-298Hardness value Hardness L (Leeb)Impacter Carbide ball type DFunctions Conversion range

Rockwell C 19.3 HRC – 68.2 HRCRockwell B 13.5 HRB – 101.7 HRBVickers 43 HV – 950 HVShore 13.2 HS – 99.3 HS Tensile strength 499 – 1996 MPa Brinell 20 – 894 HB

Automatic compensation for impact or test direction, tolerance evaluation, Offset values, data storage 1800 measured values,

Statistical analysis (average value, max. value, min. value, standard deviation), Internal counter for measurements carried out

Data output RS-232 C / DIGIMATICPower supply AC-Adapter or battery LR6 (2 pcs.)Dimensions Ø 28 x 175 mm (Measuring unit) / 70 x 110 x 35 mm (Display unit)Mass 120 g (Measuring unit) / 200 g (Display unit)

437

810-290: UD-414Application: Suitable for measuring grooves and gaps as found on gear wheels and welded corners.

810-289: UD-413Application: Suitable for measuring in narrow grooves.

810-288: UD-412Application: Suitable for measuring the inside walls of cylinders. The impact device is short and therefore guarantees the requisite stability at the measuring position.

Sample applications

810-289 810-290 810-288

“HARDMATIC” HH–411 Portable Hardness Testing DevicesWide range of detectors.•In addition to the standard universal hydraulic impactor (type D), users can choose from a wide •range of special hydraulic impactors for special measuring tasks.Type DC: for confined spaces, e.g. measuring in pipes.•Type D+15: narrow design for measuring in grooves.•Type DL: for measurements in the tightest ranges, such as welded seams or gear wheels.•


No. Designation264-504-5D “DIGIMATIC” miniprocessor

DP-1 VR937387 DIGIMATC Signal cable (1 m)09EAA069D Printing roll for DP-1 VR19BAA238 RS-232 C Signal cable526688D AC-Adapter19BAA243 Hardness testing block 880HLD

(Ø 115 mm, t 33 mm, 3,7 kg)19BAA244 Hardness testing block 830HLD




(Ø 115 mm, t 33 mm, 3,7 kg)19BAA248 Cylinder support ring

For measuring convex cylindrical surfaces (R10 to 20 mm): for types D and DC

19BAA249 Hollow cylinder support ring For measuring convex cylindrical surfaces (R14 to 20 mm): for types D and DC

19BAA250 Spherical support ring For measuring convex spherical surfaces (R10 to 27.5 mm): for types D and DC

19BAA251 Support ring for hollow sphere For measuring convex spherical surfaces (R13.5 to 20 mm): for types D and DC

19BAA457 Carbide ball For types D, DC and D+15

19BAA458 Impact device for type DL810-287 UD-411 detector

Type D approx. Ø 28 x 175 mm, approx. 120 g (Support ring Ø 22 mm)

810-288 UD-412 detectorType DC approx. Ø 22 x 85 mm, approx. 50 g (Support ring Ø 22 mm)

810-289 UD-413 detectorType D+15 approx. Ø 28 x 190 mm, approx. 130 g (Support ring Ø 11 mm)

810-290 UD-414 detectorType DL approx. Ø 28 x 230 mm, approx. 140 g (Support ring Ø 4 mm)

Documents

PRODUCTNEWS - az · 2011-10-17 · 423 Hardness Tester Rockwell Type Durotwin DT10-IS-D Rockwell/Super Rockwell Type Durotwin DFlat table Ø 63 mm, V-anvil Ø 41 mm, Rockwell/Super