Product Brochures

7/23/2019 Product Brochures

1/16


2/16


3/16

Underground Pipeline

Tank Bottoms

LPG Mounded bullet

Lida Piggy Back Wire Anode

CATHODIC PROTECTIONOxygen & Specialties

LIDA

Piggy Back wire Anode

LIDA (MMO) WIRE ANODE ( 3 mm )For Cathodic protection of Mounded of LPG Storage Bullets and Tank Bottoms

Description: LIDA MMO Wire anode (3 mm dia) assembled Piggy-back onXLPE/PVC 10 mm2 cable, complete with cable to anode joint usingsplice encapsulation kit.

Application: LIDA MMO Wire anode (3 mm dia) is used for Cathodic Protection of

mounded LPG storage bullets and tank bottoms.

LIDA (MMO) WIRE ANODE ( 1,5 mm )For Cathodic protection of Pipelines

Description: LIDA MMO Wire anode (1.5 mm dia) assembled Piggy-back onXLPE/PVC 10 mm2 cable, complete with cable to anode joint usingsplice encapsulation kit.

Application: LIDA MMO Wire anode (1.5 mm dia) is used for CathodicProtection of poorly coated pipelines as well as for hot spot protection

ADVANTAGES: Low linear resistivity. Easy to handle and install. No need to spot welding on site. Assembled in the factory. High quality and QC on connections

(Helium leak test at 2 atm and Conductivity check performed on each joint).

SPECIFICATIONS:

Durantes Vincun

WIRE SPECIFICATION UNIT UNIT

Current Rating in sand mA/mtr.75 mA/mtr. 37.5

Current Density in sand A/m2 8 A/m2 8

Dimensions (dia) mm 3 mm 1.5

Design Life (years) 30 30

Base Metal Titanium Titanium

Catalyst composition Precious mixed metal Precious mixed metal

oxide (MMO) Coating oxide (MMO) CoatingCABLE

Cable type 10mm2, XLPE/PVC 10mm2, XLPE/PVC

JOINT

Crimping and sealing with mastic and Heat Shrink Sleeve

All information, recommendations and suggestions appearing herein concerning the use of our products are based upon tests and data believed to be reliable. However, it is the usersresponsibility to determine the suitability for his own use of the products described herein. Since the actual use by others is beyond our control, no guarantee, expressed or implied, is madeby De Nora as to the effects of such use or the results to be obtained, nor does De Nora assume any liability arising out of the use by others of the products referred to herein. In addition,the information herein is not to be construed as absolutely complete since additional information may be necessary or desirable when particular circumstances exist or because of applicablelaws or government regulations. Nothing herein contained is to be construed as a recommendation to infringe any patent.

De Nora India Limited- Plot No. 184,185 & 189, Kundaim Industrial Estate - Kundaim - 403 115, Goa, India - ph +91 (0832) 3981100fax +91 (0832) 3981101 - mail [email protected] - www.denoraindia.com

www.denora.com

DE NORA


4/16

Via dei Canzi, 1

20134 Milano, Italyph: +39 02 2129 2722fax: +39 02 2129 2801

www.lidaproducts.com

Protech Business Unit

CATHODIC Protection

LIDA

Tubular Anodes

LIDA Tubular Anode

LIDA tubular anodes are

titanium tubes with a mixed metal

oxide coating. The mixed metal

oxide is a crystalline, electrically-

conductive coating that activates

the titanium and enables it tofunction as an anode.

The mixed metal oxide anode has an

extremely low consumption rate,

measured in terms of milligrams

per ampere-year. As a result of this

low consumption rate, the tubular

dimensions remain nearly constant

during the life of the anode

providing a consistently low

resistance anode.

Whether operating in soil,

freshwater, mud, or seawater,LIDA mixed metal oxide

coatings demonstrate very high

chemical stability even in

environments with very low pH

values. Unlike other impressed

current anodes, the LIDA

coatings are not affected by

the generation of chlorine.

APPLICATIONS

GroundbedsDeepShallow VerticalHorizontalOpen Hole

MarineSea WaterBrackish WaterMud

Fresh Water

FEATURES

Multi-anode conductor Lightweight / durable

High current output

Patented crimp connections

Dimensionally stable

BENEFITS

Dramatically reduces cable costs

Reduces handling andinstallation costs

Lower cost per amp-hr

Guaranteed electrical contact

and moisture seal integrity Consistently low resistance anode

Dimensions:

Anode Diameter Length Weight Surface Area

cm inches cm inches kg lbs m2 ft2

2.5 x 50 2.5 1.00 50 19.7 0.18 0.40 0.039 0.42

2.5 x 100 2.5 1.00 100 39.4 0.35 0.77 0.079 0.84

LIDA tubular 2.5 x 100 XXL are designed for extended life operation.

Please contact us when operation is expected in waters below 5 C.

Anode

Current,amps

Life, years

LIDATubular Anode Life in Sea Water

AnodeCurrent,amps

Life, years

LIDATubular Anode Life in Fresh Water

0

10

20

30

40

50

60

70

80

90

0 5 10 15 20 25 30 35 40 45 50

0

5

10

15

20

25

30

35

40

45

50

0 5 10 15 20 25 30 35 40 45 50

2.5 x 50 XL2.5 x 100 XL2.5 x 100 XXL

Maximum Current for LIDA

Tubular Anodes (life in years)


5/16

A LIDA anode string is comprised

of electrical cable threaded

through one or more tubular

anodes. Electrical connection

between the anode and cable

is via a patented, mechanical

crimping process. The crimp

connection is likewise utilized

to seal the anode around the

cable at both ends.

Since only a single cable lead

protrudes from the hole, the

junction box is eliminated when

using a LIDA string reducing

the cost of materials and labor.

String assemblies are also available

in a looped configuration with two

tails, or as multiple, staggered

strings for system redundancy and

maximum current distribution

throughout the groundbed.

De Nora Elettrodi Network

recommends the use of quality,

conductive, carbonaceous backfill,

a vent pipe and Ventralizers,

suitable cable, good design

practices, and understanding.

Please contact us or our approved

distributors for advice.

ADVANTAGES

LIDA Crimp Many impressed

current anodes are connected to

the cable with resin-based seals,

which may develop cracks or

lose adhesion to the cable or the

anode. Moisture penetration also

may occur, resulting in loss of

electrical contact.

LIDA anodes are connected with

a special crimping process which

improves the life of the tubular

anode system.

On the surface, the crimp on theends and in the middle appears

the same. Yet they serve different

purposes and are made differently.

The center crimp makes electrical

contact with the cable while the

end crimps form a moisture-

resistant seal.

Electrical connection between the

tubular anode and the power cable

wire is achieved by sliding the tube

onto the cable and crimping a

section of the tube at mid-lengtharound a stripped portion of

the cable.

Both ends of the tubular anode

are sealed over the insulated cable

by applying 50 tons of hydraulic

pressure. This crimping process

eliminates the need for mastic

or resin sealants.

Reliability In choosing the LIDA

tubular anode, you have selected

the most durable and reliableproduct in the industry for yourcathodic protection needs. LIDA

tubular anode strings are backedby a five-year, no hassle warranty.

Design, assembly and installation

factors have been carefully

considered so that your time

and costs are minimized as

much as possible.

Ease Of Installation The LIDA

anode-cable assemblies are easy to

handle, transport and install becauseof their unique flexibility. It makesyour on-site job easier as well.

LIDA Tubular Anodes

CATHODIC Protection

An

odeCurrent,amps

Life, years

LIDATubular Anode Life in Sand

AnodeCurre

nt,amps

Life, years

LIDATubular Anode Life in Coke

AnodeCurrent,amps

Life, years

LIDATubular Anode Life in Mud

0

5

10

15

20

25

30

35

40

0 5 10 15 20 25 30 35 40 45 50

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0 5 10 15 20 25 30 35 40 45 50

0

5

10

15

20

25

30

35

0 5 10 15 20 25 30 35 40 45 50

Maximum Current for LIDA

Tubular Anodes (life in years)

AnodeCurrent,amps

Life, years

LIDATubular Anode Life in Brackish Water

0

10

20

30

40

50

60

0 5 10 15 20 25 30 35 40 45 50

LIDA is a U.S. registered trademark of ELTECH Systems Corporation. LIDA is a registered trademark worldwide of Oronzio de Nora SA licensed exclusively to the De Nora Elettrodi Network.Ventralizer is a trademark of ELTECH Systems Corporation.

All information, recommendations and suggestions appearing herein concerning the use of our products are based upon tests and data believed to be reliable. However, it is the usersresponsibility to determine the suitability for his own use of the products described herein. Since the actual use by others is beyond our control, no guarantee, expressed or implied, is made byDe Nora Elettrodi Network Companies as to the effects of such use or the results to be obtained, nor does De Nora Elettrodi Network Companies assume any liability arising out of the useby others of the products referred to herein. In addition, the information herein is not to be construed as absolutely complete since additional information may be necessary or desirable whenparticular circumstances exist or because of applicable laws or government regulations. Nothing herein contained is to be construed as a recommendation to infringe any patent.

In chloride rich soils or muds, a suitable chlorine resistant cable must be used with the anodes.

Please contact us when operation is expected in waters below 5 C.

Via dei Canzi, 1, 20134 Milano, Italy ph: +39 02 2129 2722 fax: +39 02 2129 2801 www.lidaproducts.com

2.5 x 50 XL2.5 x 100 XL2.5 x 100 XXL


6/16

Aug 11, 2004 Page 1 of 2ISO 9001:2000 REGISTERED

ANOTEC Industries Ltd. Distributed by:5701 Production Way, Langley, BC Canada V3A 4N5Telephone 604 / 514-1544 - Fax 604 / 514-1546web site: www.anotec.com - e-mall: [email protected]

Produxt

Bulletin

90-9

04-07-31

ANOTEC Stick AnodesSolid Chill Cast High Silicon IronFor Impressed Current Cathodic Protection

Composition(weight %)

Grade 3ASTM A518

Silicon 14.20 14.75%Chromium 3.25 5.00%Carbon 0.70 1.10%Manganese 1.50% maxCopper 0.50% maxMolybdenum 0.20% max

"Chill Cast" inMetal Molds

Assures consistent weight, greater density, less flake graphite grain boundary,

and lower chemical segregation than Sand Cast Anodes.

ANOTEC Chill Cast structure is similar to "Spin Cast" Tubular Anodes.

More than Twiceas Strong

Independent laboratory tests confirm that Anotec Anodes withstand drop

impact tests to more than twice the height of Sand Cast Anodes.

Quality Control

ISO 9001:2000 Quality Control assures: chemistry (by spectrometer),

Impact strength and production lot traceablility.

Performance

Accelerated Corrosion Tests confirm that Anotec Chill Cast anodes

perform significantly better (up to19%) than Sand Cast anodes inchloride and sulphate environments. Test reports available on request.

Spherical Tip

Prevents hang-up when lowering into deep wells.

Product Description

Special Features

CableConnection

Options

CaulkedLead

PinType


7/16

Aug 11, 2004 Page 2 of 2ISO 9001:2000 REGISTERED

A typicalANOTECAnode

CrossSection

A dense skin of

minute columnar

grains and a dense

core of equiaxial

grains.

Occasionally, veryfine interdendritic porosity at center. Predominantlyspheroidal shaped graphite. Similar to the structure ofvacuum refined High Silicon Iron.

Grain Structure Makes a Difference

Anotec Solid Chill Cast Anodes

Skin of non-porous

equiaxial grains. Remainingsection relatively porous from interdendritic shrinkage and

porosity. Predominantly flake graphite with larger boundaryareas than equivalent spheroidal graphite.

AnotecType

SHA

EHA

EHKEHR

EHMEMK

A A

A D

LA

A typicalCross

SectionOf aSand Cast

Anode

Shipping InformationNominal DimensionsInches(mm)

NominalGross Weight

AnotecType

D L A

Nominal WeightLb.(Kg)

Nominal AreaSq. Ft.

(Sq. M.)Anodesper crate

Lbs. Kgs

SHA2

(51)60

(1520)2.2(56)

43(20Kg)

2.6(.24)

50 2300 1044

EHA

2

(51)

60

(1520)

3

(76)

44

(20Kg)

2.6

(.24) 50 2375 1078

EHM2

(51)60

(1520)3

(76)60

(27Kg)2.7

(.25)45 2850 1293

EHK1.5(38)

60(1520)

2.2(56)

26(12Kg)

2.0(.19)

70 1970 894

EMK1.5(38)

60(1520)

2.2(56)

27(12.7)

2.0(.19)

60 1770 803

EHR3

(76)60

(1520)4

(102)110

(50Kg)3.9

(.36)24 2790 1266

Crate dimensions nominal 32W x 22H x 62L inches = 25.2Ft3 81W x 56H x 158L cm = .71 M3

D

D


8/16

Earth Contact BackfLORESCO

Loresco RS3 is the newest and most

innovative super conducting earth contact

backfill in the Loresco product line. RS3

combines the characteristics of superior low

resistivity and high bulk density with a

remarkably rapid sinking ability to provide

the latest in conductive carbon backfill

technology. Because of the new rapid sinking

ability RS3 is able to achieve maximum

compaction quickly. Rapid sinking allows for

a faster construction completion time and

faster energizing of the anode system. Rapid

sinking allows for pouring when pumping isnot an option. RS3 is able to handle the

demands of stringent field requirements. This

is the first time a conductive carbon backfill

combining pumping ability and pouring

ability has been available in one bag. RS3 is

manufactured under a new process which

creates a new surface with superior

conductive properties. This manufacturing

process is exclusive to conductive carbon

formulations designed for cathodic

protection. The new manufacturing process

ensures the impressed current anode and

RS3 system have increased electronic flow

performance to further increase the life of the

anode system. Loresco RS3 is produced

specifically for cathodic protection

applications using an exclusive multi-

step process.

First, a very high quality base carbon with

desired characteristics is selected. Next, this

carbon is calcined to a minimum temperature

of 1250 C under very exacting and

controlled standards. This step results in

semi-graphitized carbon particles with

excellent conductivity. All particles shaped

and surface modified for maximum electrical

conductivity and high-current applications.

Then, to further improve the bulk

conductivity, the surfaces of the individual

particles are modifiedto enhance the contact

conductance in a process exclusive only to

the corrosion industry. This breakthrough in

surface alteration ensures maximum

electronic current transfer with positive

anode contact. Finally, a specially

formulated surfactant is added to reduceparticle surface tension for compact settling

under water.

Loresco RS3 has a bulk density of 68 lbs

per cubic foot. The fixed carbon content is

greater than 99% by weight. The bulk density

and high fixed carbon content coupled with

the assured low resistivity medium allows

for longer groundbed life at a loweroperating cost.

INSTALLATION

Loresco RS3, due to its maufacturing

process, is simple to install by either mixing

and pumping or by pouring dry. With deep

anode systems, pumping from the bottom up

is recommended. Loresco RS3 has superbpumping qualities due to the addition of

surfactants and when agitated in water, takes

on the characteristics of super heavy mud.

Time before energizing is greatly reduced

after installing RS3. The modified surface of

the carbon particles coupled with the action

RS3


9/16


10/16

The Ultimate Connection For Quality Products and Service

+1-918-627-5210 SALES SERVICE TECHNICAL SUPPORT VISIT www.thermOweld.com10

thermOweldthermOweld

WELD

METAL

thermOweld Weld Metal is packaged in moisture-resistant plastic

cartridgesthat have tight fitting caps. These cartridges and the necessarysteel discs are then packaged in boxes that are shrink-wrapped. Thisinsures the weld metal arriving in good condition, always dry, and ready for apositive ignition every time.thermOweld Weld Metal comes in four types; one for welding copperto copper or copper to steel, copper to rail, copper to cast iron and onefor welding copper to steel for cathodic protection. The size and weight(in grams) of the cartridge are marked on each individual cartridge.thermOweld Weld Metal is available to be shipped via ground, air orocean freight.All sizes of weld metal are eligible for thermOwelds SDS (Same DayService) shipment.

STANDARDCARTRIDGE

SIZE

CAST IRONCARTRIDGE

SIZE

CATHODICPROTECTIONCARTRIDGE

SIZE

RAILCARTRIDGE

SIZE

PACKED PERBOX

#15 #15CI #15CP #15R 20#25 #25CI #25CP #25R 20#32 #32CI #32CP #32R 10#45 #45CI #45CP #45R 20#65 #65CI #65CP #65R 20#90 #90CI ~ #90R 10

#115 #115CI ~ #115R 10#150 ~ ~ #150R 10#200 ~ ~ #200R 10#250 ~ ~ #250R 10#500 ~ ~ #500R 10

thermOweld Weld Metal is sold in box quantities only


11/16


+1-918-627-5210 SALES SERVICE TECHNICAL SUPPORT VISIT www.thermOweld.com 23


CS-32CS-32 TYPE MOLDSHorizontal Cable to Horizontal Steel Pipefor Cathodic Protecion

CS-32 Type Molds are used to terminate a horizontal coppercable to horizontal steel pipe. Note that the cable is OFF

the surface.Size range is 2.5 mm through 70 mm solid or concentricstranded copper conductors.

CABLE SIZE(mm)

Pipe Dia.in mm

MOLD #PRICE

KEY

WELD

METAL

HANDLECLAMPS

2.5, 4 & 6 up to 125 M-4146 3 15 Not Reqd2.5, 4 & 6 over 125 M-4147 3 15 Not Reqd

10up to 125 M-4150 3 25 Not Reqdover 125 M-4151 3 25 Not Reqd


25up to 70 M-4152 3 25 Not Reqd70 to 165 M-4153 3 25 Not Reqdover 165 M-4154 3 25 Not Reqd

30

up to 70 M-2833 3 32 Not Reqd70 to 165 M-2834 3 32 Not Reqd

165 to 250 M-2835 3 32 Not Reqdover 250 M-2836 3 32 Not Reqd

35



50



70



38-4590 Sleeve/Weld Req'd 38-4588 Sleeve/Weld Req'd For sizes not listed, contact thermOweld. For heavy duty molds or molds with wear plates, contact thermOweld. For expedited service, contact thermOweld. Required Tools; Handle Clamps w/ Flint Ignitor (see chart above for correct handles) ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor Other recommended accessories; 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41)

CABLE SIZE(mm)

Pipe Dia.in mm

MOLD #PRICE

KEY

WELD

METAL

HANDLECLAMPS

2.5, 4 & 6 Flat M-4188 3 45CI Not Reqd10 Surface M-4189 3 45CI Not Reqd16 or M-4188 3 45CI Not Reqd25 750 Dia M-4191 3 45CI Not Reqd35 and M-4192 3 45CI Not Reqd50 above M-4193 3 45CI Not Reqd70 pipe M-2868 3 65CI Not Reqd

38-4590 Sleeve/Weld Req'd 38-4588 Sleeve/Weld Req'd 38-4589 Sleeve/Weld Req'd For sizes not listed, contact thermOweld. For heavy duty molds or molds with wear plates, contact thermOweld. For expedited service, contact thermOweld. Required Tools; Handle Clamps w/ Flint Ignitor (see chart above for correct handles) ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor Other recommended accessories; 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41)

CS-33CS-33 TYPE MOLDSHorizontal Cable to Horizontal Cast Iron Pipefor Cathodic Protecion

CS-33 Type Molds are used to terminate ahorizontal copper cable to horizontal cast ironpipe. Note that the cable is OFFthe surface.Size range is 2.5 mm through 70 mm solid orconcentric stranded copper conductors.


12/16


+1-918-627-5210 SALES SERVICE TECHNICAL SUPPORT VISIT www.thermOweld.com24


CS-34CS-34 TYPE MOLDSHorizontal Thru Cable to Horizontal Steel Pipefor Cathodic Protection

CS-34 Type Molds are used to join horizontal throughcopper cable to horizontal steel pipe. Note the cable is OFF

the surface.Size range is 2.5 mm through 50 mm solid or concentricstranded copper conductors.

CABLE SIZE(mm)

Pipe Dia.in mm

MOLD #PRICE

KEY

WELD

METAL

HANDLECLAMPS

2.5, 4 & 6 up to 105 M-4167 3 25 Not Reqd2.5, 4 & 6 over 105 M-4168 3 25 Not Reqd



25up to 70 M-4173 3 32 Not Reqd70 to 165 M-4174 3 32 Not Reqdover 165 M-4175 3 32 Not Reqd

35



50



(2) 38-4590 Sleeves/Weld Req'd (2) 38-4588 Sleeves/Weld Req'd (2) 38-4589 Sleeves/Weld Req'd For sizes not listed, contact thermOweld. For heavy duty molds or molds with wear plates, contact thermOweld. For expedited service, contact thermOweld. Required Tools; Handle Clamps w/ Flint Ignitor (see chart above for correct handles) ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor

Other recommended accessories; 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41)

CS-35CS-35 TYPE MOLDSHorizontal Thru Cable to Horizontal Cast Iron Pipefor Cathodic Protection

CS-35 Type Molds are used to join horizontal throughcopper cable to horizontal cast iron pipe. Note the cable isONthe surface.Size range is 2.5 mm through 70 mm solid or concentricstranded copper conductors.

(2) 38-4590 Sleeves/Weld Req'd (2) 38-4588 Sleeves/Weld Req'd (2) 38-4589 Sleeves/Weld Req'd

For sizes not listed, contact thermOweld. For heavy duty molds or molds with wear plates, contact thermOweld. For expedited service, contact thermOweld. Required Tools; Handle Clamps w/ Flint Ignitor (see chart above for correct handles) ~ Sold complete with frame 38-0309-00 ~ Flint Ignitor Other recommended accessories; 38-3922-00 ~ Mold Cleaning Brush (pg 40) 38-0135-00 ~ Cable Cleaning Brush (pg 40) 38-0101-00 ~ Rasp (pg 41)

CABLE SIZE(mm)

Pipe Dia.in mm

MOLD #PRICE

KEY

WELD

METAL

HANDLECLAMPS

2.5, 4 & 6 Flat M-2876 3 32CI Not Reqd10 Surface M-2882 3 45CI Not Reqd16 or M-2883 3 45CI Not Reqd25 750 Dia M-2884 3 45CI Not Reqd35 and M-2887 3 45CI Not Reqd50 above M-2889 3 65CI Not Reqd70 pipe M-2890 3 65CI Not Reqd


13/16

Klippon POK

The POK series is based on a high-quality glass fibre-reinforced

polyester enclosure which represents an economical solution for

electrical connections.

The enclosures are ideal wherever corrosion resistance, impact

resistance and a high IP protection class are required.

Features:

17 sizes

Cover with stainless steel screws

Mounting holes located outside of the sealed area

Threaded holes for mounting rails and mounting plates

Approved to the latest international standards

Our assembly service can supply these enclosures preassembled

with terminals and cable glands according to customer

requirements.

Technical data Standard ATEX

Material Glass fibre-reinforced polyester Glass fibre-reinforced polyester

to DIN 16913 to DIN 16913 with added graphite

Surface Grey, similar to RAL 7001 Black, similar to RAL 9011

Gasket Chloroprene + polyurethane Silicone (VMQ)

Cover screws Stainless steel Stainless steel

Protection class IP 66 IP 66

Impact resistance 7 J 7 JTemperature range 40 C to +90 C T silicone 55 C to +100 C

Flammability UL94 V0 UL94 V0

Toxicity Halogen- and cadmium-free Halogen- and cadmium-free

Polyester enclosures

Approvals

KEMA 03ATEX2078 U

T II 2 G EEx e II

KEMA 03ATEX2077

II 2 G EEx e II T6

T I I 2 (1 ) G EEx e [ia] IIC T6

II 1 G EEx ia IIC T6

Overview of enclosures

Type H x W x D 75 x 80 x 55 75 x 110 x 55 75 x 160 x 55 75 x 190 x 55 75 x 230 x 55 120 x 122 x 90

Standard, RAL 7001 1277200000 1277300000 1277400000 1565400000 9510510000 1277500000

For hazardous areas (Ex), RAL 9011 9510210000 9510220000 9510320000 9510330000 9510340000 9510230000

Type H x W x D 120 x 220 x 90 160 x 160 x 90 160 x 260 x 90 160 x 360 x 90 160 x 560 x 90 250 x 255 x 120

Standard, RAL 7001 1277600000 1565410000 1277700000 1277800000 9510520000 1565420000

For hazardous areas (Ex), RAL 9011 9510240000 9510250000 9510260000 9510270000 9510350000 9510280000

Type H x W x D 250 x 400 x 120 250 x 600 x 120 405 x 400 x 120 250 x 255 x 160 250 x 400 x 160

Standard, RAL 7001 1565430000 9510470000 1565440000 9510530000 9510540000

For hazardous areas (Ex), RAL 9011 9510290000 9510300000 9510310000 9510360000 9510370000

Note: Please specify ambient temperature of application when ordering and also note gasket material (e.g. 55 C / silicone gasket)

A.58

A

Enclosures


14/16

EEEEnnnnggggiiiinnnneeeeeeeerrrriiiinnnngggg SSSSoooolllluuuuttttiiiioooonnnn BBBBaaaasssseeeedddd oooonnnn SSSSoooouuuunnnndddd FFFFoooouuuunnnnddddaaaattttiiiioooonnnn

STELTH 2

Direct burial in chloride free conditions

Size: 1.5 (4 cm) Diameter x 7 (18 cm) long.

Lead Wire: 50 (15m) of # 14 (2.5mm2) RHH-RHW wire

Material: Ceramic with Moisture Retention Membrane

Stability: 5 millivolts with 3.0 microamps load

Temperature Range: -10 to 176F (-23 to 80 C)

Stelth Model SRE-007-CUYCopper-Copper Sulfate (Cu-CuSO4)for buried or concrete service in chloride free environments

Stelth Model SRE-008-SUBSilver-Silver Chloride (Ag-AgCI)for buried or concrete service in chloride environments

Stelth Model SRE-009-ZUR

Zinc-Zinc Chloride (Zn-ZnSO4)for buried or concrete service in chloride free environments


15/16Tinker & Rasor quality is found in our products, our people and our customer service.

An ISO 9001 Registered Company

www.tinker-rasor.com [email protected]

AVAILABLE FROM STOCK!

Distributed by

Shunts and otheraccessories available

The Model T-3 is the most versatile CathodicProtection Test Station available.UV stabilized, Fire resistant and Impactresistant poly carbonate material for long outdoorlife.Fits 3.5 OD riser pipe, also available from stock inthree colors. Reducing adapters available for smallerO.D.s, and a flange adapter, as well.Large, clear terminal board can handle a variety of

custom configurations, including voltmeters, shunts,resistors, potentiometers and more.See our website for more information

Features:8 Colors11 terminal positions5 Rapid Connect binding posts

Clear terminal boardUV Stabilized colorFire resistant, impact resistantFits 3.5 OD Risers (also available)

teststations.

www.

.com

CP TEST STATION

MODEL T-3

T

MODE

R

O

www.detectron.comwww.teststations.com


16/16

CORROSION MITIGATION INSTRUMENTATION

PRODUCTDATASHEET

MODEL T-3 CP TEST STATIONS

www.teststations.com

Features:

Construction:

Applications:

Recommendations:

Environment:

Dimensions:

11 hole terminal board 5 Rapid connection binding posts Clear terminal board 8 colors from stock Fits 3.5 OD riser pipe UV Stabilized color protection High impact resistance Fire resistant Easy Grip top for easy opening with gloves Anti-Spin gasket prevents twisting

Polycarbonate material (Lexan)gives great UV stabilization, fire protection andimpact resistance.Rapid connection binding posts are zinc platedbrass for excellent corrosion resistance.

Cathodic Protection connection point

Use with optional items such as the T&R

Shock Guard which can be combined withbanana jacks for personnel safety.

Also can be custom printing which may meetDOT ID requirements for urban environments.

-76C to 122C (-105F to 252F)

Complete Test Station:Terminal Board:5.3 x 3.52 (134.6mm x 89.4mm)Cover: 5.1 x 4.4 (129.5mm x 111.75mm)Shipping -

Weight: 1 lbs (0.45 kg)Dimensions: 6 x 6 x 4(152mm x 152mm x 101.6mm)

DELIVERY: Immediately from STOCK F.O.B. San Gabriel, CA USASERVICE: 24-hour Turn-AroundTERMS: Net30 Days, on approval of creditWARRANTY: 90 Days, parts and labor

AVAILABLE FROM STOCK

Custom configurationsand printing available onModel T-3 test stations

Model T-3 CP Test Stations come standard withthe unique Tinker & Rasor binding post with setscrew. This binding post allows for rapid wireconnections on wires as big as 6 AWG.Each T-3 comes with five (5) zinc plated bindingposts, and up to eleven (11) binding posts oncustom orders.

The T-3 also features a clear terminal boardmake of a tough, fire resistance polycarbonateresin. The clear terminal allows you to view bothsides of the terminal board without obstruction.

The terminal board has eleven (11) terminalpositions, most on 1 centers from another, andcan be filled with our binding posts, stainlessscrews or banana jacks, on custom orders.

Documents

Product Brochures