40
APARATURA PENTRU TESTARE MATERIALE DE CONSTRUCTII

PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII 2009

  • Upload
    costty

  • View
    1.618

  • Download
    0

Embed Size (px)

DESCRIPTION

Catalog de testare materiale de constructii

Citation preview

Page 1: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

APARATURA PENTRU TESTARE

MATERIALE DE CONSTRUCTII

Page 2: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009
Page 3: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

PREZENTARE GENERALA

Page 4: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

I. ConcreteFull Automatic Concrete Compression Test MachineFlexural Test on Concrete BeamsFlexural Test on Concrete BlocksFlexural Test on KerbsBlocks Test Platens with sliding rail assemblyBlocks Test Platens Fitted to Compression MachineSplitting Tensile Test Device for Cylindrical SpecimensSplitting Tensile Test Device for Concrete Block PaversSplitting Tensile Test Device for Concrete CubesSpecific Gravity FrameConcrete Beam MouldsConcrete Cube MouldsVibrating TableConcrete Impermeability ApparatusBulk Density MeasuresWaltz ContainerSlump Test SetFlow Table (Laboratory Method)Air Entrainment MeterCuring TankVebe ConsistometerSpecific Gravity FrameV FunnelL Shape BoxHydraulic Universal Testing Machine

Cement Flow Table EN ModelAutomatic Programmable and Manual Mortar MixerJolting TableCuring CabinetLe Chatelier Water BathBlaine Fineness ApparatusLe Chatelier Test SetVicat Test SetCement Compression and Flexure MachineCement MouldsLe Chatelier FlaskCement Flow Table ASTM Model

II. Cement

pg. 2pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3pg. 3 pg. 4pg. 4pg. 4pg. 5pg. 5pg. 5pg. 6pg. 6pg. 6pg. 7pg. 7pg. 7pg. 8

pg. 10pg. 10pg. 11pg. 11pg. 11pg. 12pg. 12pg. 13pg. 13pg. 15pg. 15pg. 15

Cuprins

Page 5: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Cuprins

III. AgregateAbrasion Testing MachineShape Index GaugeDetermination of Resistance to Freezing and Thawing Climatic ChamberMethylene Blue Test SetMicro-Deval Testing MachineSkid Resistance and Friction Tester (Skid Tester)AAV Abrasion MachineAccelerated Polishing MachineSand Equivalent Test SetLos Angeles (Determination of Resistance to Fragmentation)Testing SievesThermometersWater BathMuffle FurnaceU Shape BoxDigital BalancesLaboratory HardwareLaboratory GlasswarePorcelain / Mortar and PestlesSieve ShakerDrying OvenVacuum PumpCasagrandeSand Cone Density SetSand Equivalent ShakerFlakiness SievesGrid SievesAutomatic Soil CompactorSand Replacement Test SetStandard / Modified Proctor Mould and Rammer

Marshall Stability MachineAsphalt Mixer (5lt)Asphalt Mixer (10lt)Bitumen PenetrometerDuctility Testing MachineSoftening Point (Ring and Ball) ApparatusLoss on Heating Oven (TFOT)"Vialit Plate" Adhesion Test ApparatusCore Drilling MachineCentrifuge ExtractorManual Marshall Hammer Assembly Automatic Marshall Compactor Saybolt ViscometerMarshall MouldUniversal Extruder

IV. Asphalt

pg. 16pg. 16pg. 16pg. 17pg. 17pg. 18pg. 18pg. 18pg. 19pg. 19pg. 20pg. 20pg. 21pg. 21pg. 22pg. 22pg. 22pg. 23pg. 23pg. 24pg. 24pg. 25pg. 25pg. 25pg. 26pg. 26pg. 27pg. 27pg. 28pg. 28

pg. 29pg. 30pg. 30pg. 30pg. 31pg. 31pg. 32pg. 32pg. 32pg. 33pg. 33pg. 34pg. 34pg. 34

Page 6: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

2

Full Automatic Concrete Compression Test Machine

Product Code: UTC - 4320 & UTC - 4420Standards: EN-12390-4, BS 1881, ASTM C-39

• Automatic test cycle with standard Rapid Approach• Graphical - LCD Data Acquisition and Control System• Menu Driven Software for easy operation• Load vs time plot and instantaneous load rate displayed• Accurate load rate control within ±5 from 1 kN/sec to 20 kN /sec• Class 1 starting from % 10 of the full range• Ready Stress Calculation for the standards of EN 12390-3, EN 12390-5, EN 12390-6, EN 1338,EN 1340, EN 196• SI, Metric, Imperial Units• Data storage up to 256 tests• RS 232 output for printer or PC• Free of charge PC software for test control and advanced report printout

The UTEST automatic range of 2000 kN and 3000 kN capacity compression testing machines has been designed to meet the need for reliable and consistent testing of concrete samples. All UTEST machines feature the complete automatic test cycle with a closed loop digital readout.Once the specimen parameters have been introduced, it is sufficient to press the START button to complete the test.

The main characteristics are• High resolution 65.000 points• 240*120 pixel blue-white graphic LCD display• Standalone full automatic testing capacity• CPU card by microprocessor 32 bit ARM risk architecture• Can make manual tests if required•Large permanent memory up to 256 test results• RS232C (optional Ethernet) connection at 57600 band• One RS232 serial port for connecting either PC or printer for data transmission• Two analogical channels, use for Load Cell or pressure transducer• A sample type and dimensions can be entered respect to the standards• 18 key touch membrane keyboard• Easy to operate with 6 main function keys• Language select; English, Turkish, Russian• Can control two frames• Dual stage pump• 750 W power• 25 liter oil capacity• 60-100 mm/min fast approach speed

ModelCapacity

kN

Class 1 range

kNResolution

Overall Dimensions

mm L x W x H

Power

W

UTC – 4320 2000 200 - 2000 1/ 64.000 800×425×964 750

UTC – 4420 3000 300 - 3000 1/ 64.000 845×465×1048 750

www.precisa.ro

Concrete

Page 7: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

3

ModelRam

Travel mm

Max. Distance

Between Platens mm

Weight

Kg

Platen Diameter

mm

UTC – 4320 50 340 300 800

UTC – 4420 50 340 300 1100

Flexural Test on Concrete BeamsFlexural Test on Concrete BlocksFlexural Test on KerbsBlocks Test Platens with sliding rail assemblyBlocks Test Platens Fitted to Compression MachineSplitting Tensile Test Device for Cylindrical SpecimensSplitting Tensile Test Device for Concrete Block PaversSplitting Tensile Test Device for Concrete CubesSpecific Gravity Frame

Concrete Beam Moulds

Concrete Cube Moulds

Product Code: UTC- 0115 100x100x400 mm Steel beam mouldUTC- 0115/1 100x100x500 mm Steel beam mould

UTC- 0116 150x150x600 mm Steel beam mouldUTC- 0116/1 150x150x750 mm Steel beam mould

Standards: EN 12390/1, ASTM C39, C192, AASHTO T23, T126

Product Code: UTC- 0101 150x150x150 mm Steel UTC- 0102 150x150x150 mm Plastic

UTC- 0103 200x200x200 mm SteelUTC- 0104 100x100x100 mm Steel

Standards: EN 12390/1, ASTM C39, C192-AASHTO T23, T126

Steel beam moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Two part and clamp attached base plate steel moulds are designed to be durable, resistant and easy to clean.

Cast iron, hard plastic or steel cube moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Four part and clamp attached base plate cast iron and steel moulds are designed to be durable, resistant and easy to clean.

Weight (approx.) : UTC- 0115 20,3 kgUTC-0115/1 18,5 kg

UTC- 0116 38,4 kgUTC- 0116/1 40 kg

Weight (approx) : UTC- 0101 16,2 kgUTC- 0102 2,2 kg

UTC- 0103 20,2 kgUTC- 0104 7,0 kg

Concrete

[email protected]

Page 8: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Vibrating Table

Concrete Impermeability Apparatus

General PropertiesThe UTEST fixed amplitude vibrating table is a compact unit providing controlled vibrocompaction in the laboratory using cube or cylinder moulding equipment. Vibrating tables consists of vibrating motor, control unit and clamping assembly. The table is available in two alternative sizes, 610 x 380 mm and 1260 x 620 mm. Small table accepts 2, large table accepts 4 cube, cylinder moulds or beam moulds by using clamping assembly.

Operates with 220 Volt, 50 Hz supply

Dimensions : UTC–0159 610x380x780 mm (wxlxh) 60 kg UTC–0161 1055×620×1055 mm (wxlxh) 154 kg

Used for the determination of the depth of penetration of water to hardened concrete specimens under pressure. 3 and 6 specimen capacity models are available. The system can test 150x150x150 mm, 200x200x200 mm cube or 150x300mm cylinder specimens. Pressure to the sample, up to 10 bar with 0,2 bar precision is generated by way of compressed air applied to the integral water tank and controlled by a pressure regulator; with a pressure gauge. The penetration of water is measured through the burettes supplied complete with the system. Thesystem comprises impermeability gaskets for every cell. The apparatus has to be fitted with the suitable air compressor with maximum working pressure of 10 bar.

Dimensions : UTC- 0244/A 500x500x1800 mm (lxwxh) 95 kg UTC- 0244/B 500x500x1800 mm (lxwxh) 106 kg

Product Code: UTC–0159 Vibrating Table (Small)UTC–0161 Vibrating Table (Large)

Standards: EN 12390–2

Product Code: UTC- 0244/A Three place ModelUTC- 0244/B Six place Model

Standards: EN 12390-8, ISO 7031

www.precisa.ro

Concrete

4

Bulk Density Measures Product Code: UTA–0445/1 1 dm³UTA–0445/2 5 dm³

UTA–0445/3 10 dm³UTA–0445/4 20 dm³

Standards: EN 1097–3

Bulk Density Measures are manufactured from heavy gauge steel complying with the related standard. Available in 1, 5, 10 and 20 liter capacity models according to the requirements of different standards. Coated against corrosion.

Weight (approx.) : UTA-0445/1 1 dm³ 1,2 kgUTA-0445/2 5 dm³ 6,1 kgUTA-0445/3 10 dm³ 8.8 kgUTA-0445/4 20 dm³ 12,5 kg

Page 9: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Waltz Container

General PropertiesWaltz Container consists of a 200x200x400 mm (width x depth x height) metal container with two carrying handles.Coated against corrosion.

Slump Test Set

Flow Table (Laboratory Method)

Product Code:UTC–0149 Slump Test SetUTC–0140 Tamping rod 16x600 mm

UTG–0149/5 Steel rulerUTG–0145 Rubber mallet

UTG–1611 Laboratory shovelStandards: EN 12350–2, BS 1881: 102, ASTM C143, AASTHO T119

Product Code: UTC- 0164 (Manual)UTC- 0165 (Motorized)

UTC- 0164/1 Flow MouldUTC–0140 Tamping Rod 16x600 mm

Standards: UNI 8020-A

The Slump test method is used for the determination of the consistency, the medium and high workability of fresh concrete.The set consists of slump cone, slump cone funnel, 600 mm long x 16 mm diameter tamping rod which is hemispherical at both ends, base plate, rubber mallet and steel rule. Supplied either galvanized or paint coated to prevent corrosion.

Weight (approx) : 5 kg

The apparatus consists of 762 mm dia. stainless steel circular table and stainless steel flow mould. A sample of concrete is tamped into the flow mould and then the mould is removed.The test is based on measuring a percentage increase in diameter of spread concrete against the moulded concrete by lifting and dropping the table 15 times in about 15 seconds.Manual or motorized models are available.

UTC-0169 18.9 kg

Product Code: UTC-0146Standards: EN 12350-4

Concrete

[email protected] 5

Page 10: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Air Entrainment Meter

Curing Tank

Vebe Consistometer

The apparatus is used to determine air content of fresh concrete. It consists of a flanged 7 liter capacity cylindrical vessel and cover assembly incorporating a pressure gauge air pump and valves.The meter measures up to 22% entrained air with an accuracy of ±0.25% at full scale. It is appropriate for aggregates size of maximum 50 mm. The instrument can be calibrated and it is supplied complete with straight edge and tamping rod.

Weight (approx.) : 3,5 kg

Used for the determination of the depth of penetration of water to hardened concrete specimens under pressure. 3 and 6 specimen capacity models are available. The system can test 150x150x150 mm, 200x200x200 mm cube or 150x300mm cylinder specimens. Pressure to the sample, up to 10 bar with 0,2 bar precision is generated by way of compressed air applied to the integral water tank and controlled by a pressure regulator; with a pressure gauge. The penetration of water is measured through the burettes supplied complete with the system. Thesystem comprises impermeability gaskets for every cell. The apparatus has to be fitted with the suitable air compressor with maximum working pressure of 10 bar.

Dimensions : UTC- 0244/A 500x500x1800 mm (lxwxh) 95 kg UTC- 0244/B 500x500x1800 mm (lxwxh) 106 kg

The method is a mechanised variation of the slump test and includes determination of workabilityof fresh concrete by performing vibration to concrete after removal of the slump cone. The assembly is mounted upon a small vibrating table operating at a fixed amplitude and frequency.The time to complete the required vibration gives an indication of the concrete workability. The set consists of vibrating table, slump cone, graduated rod with transparent plate, filling cone and tamping rod.

Dimensions : 220x280x710 mm (lxwxh)Weight (approx) : 87 kg

Product Code: UTC- 0170 Air Entrainment MeterUTC- 0170/1 Tamping Rod (106X300 mm)

UTC- 0170/2 Straight EdgeUTC- 0170/M Manometer

Standards: EN 12350–7, ASTM C231, AASHTO T152

Product Code: UTC- 0191 Curing TankUTC-0191/3 Set of 8 Upper Racks

Standards: EN 12390–2, ASTM C31, C192, C511

Product Code: UTC-0195Standards: EN 12350-3

www.precisa.ro

Concrete

6

Page 11: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Specific Gravity Frame

V Funnel

L Shape Box

Product Code:UTC-0612 Specific Gravity FrameUTC-0612/1 Cradle

UTC-0612/3 Water TankStandards: EN 12390-7, BS 1881:114

Product Code: UTC- 0147Standards: UNI 11042, Rilem report No. 23

Product Code: UTC- 0147/BStandards: UNI 11043, Rilem report No. 23

Used in conjunction with a suitable electronic balance for specific gravity determination of fresh and hardened concrete and aggregates. A purpose built robust frame designed to support the electronic balance. The lower part of the frame incorporates a moving platform, which carries the water tank allowing the test specimens to be weighed in both air and water. The balance is not included in the test set and must be ordered separately. Any type of electronic balance fitted with under-bench weighing facility can be used.Lifting device, cradle and plastic water tank are supplied complete with frame.

Dimensions : 400x500x970 mm (wxlxh)

The apparatus is used to evaluate the segregation resistance of freshly mixed self compacting concrete by the observation the flowing speed due to the difference of samples remaining period in the funnel.The test set consists of a stainless steel funnel placed vertically on a supporting stand.The discharge orifice is equipped with a lid, which can be momentarily opened.Dimensions : 570x920x300 mm (lxwxh)Weight (approx.) : 6 kg

The L Shape Box is used for evaluation of self compactability (confined flowability) of freshly mixed self compacting concrete. The box gives the opportunity to evaluate different properties, such as filling ability, passing ability and resistance to segregation.

Dimensions : 700x200x600 mm (lxwxh)Weight (approx.) : 18 kg

Concrete

[email protected] 7

Page 12: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Data Acquisition and Control System BC100

LCD graphics data acquisition and controls system BC100 is designed to control the machine and processing of data from load cells or pressure transducers and displacement transducers or extensometers installed on the universal testing machine frame. The easy to read LCD graphic display and touch-button data pad keys make the unit quick and straight forward to operate. All interactions with the measuring system are via the front control panel by using simple menu-driven procedures. The BC100 is contained in light alloy housing and its design satisfies the ergonomic requirements for various uses. The BC100 digital graphic display allows real time load vs. time graph. At the end of the test cycle, the results can be stored in the large memory or downloaded to a PC in UTEST software format. Dedicated software package is available for further online data processing, database management and certificate printing.

Hydraulic Grips Hydraulic powered jaws completely stop the possibility of sample skidding from the jaw enabling for correct and definite strain measurements. Hydraulic jaws are very safe and user friendly. Hydraulic jaws come with jaw sets for pulling 0 – 40 mm flat and 6 – 50 mm diameter cylinder samples. The hydraulic jaw set has an independent hydraulic power unit with a working pressure of 300 bars.

Material Test Software (MTP)Material testing software supplied standard with the machine is used to control and data processing. By using MTP Test control data input (test speed, maximum load and maximum elongation limits, etc.), sample data and user data can be entered. Test results can be displayed in metric, SI and US customary unit systems. Load- strain, stress- % strain can be displayed graphically. Can calculate max. load, max. starin , break load, break strain, young modulus, yield, etc. Can give an experiment report that consists of input data, graphics and test results.

www.precisa.ro

Concrete

Hydraulic Universal Testing Machine

Product Code: UTM-3000 Hydraulic Universal Testing Machine 400 kN CapacityUTM-4000 Hydraulic Universal Testing Machine 600 kN Capacity

Standards: EN 10002-1, ASTM 370

Universal hydraulic tensile test machine is designed to test the ferrous materials for structural values such as breaking point, breaking tensile, maximum load and maximum tensile. Apart from tensile tests, Universal test machines can also be used for standard test such as flexure and compression tests up to the capacity of the machine.Universal test machines are produced in two different models having 40 and 60 ton capacities.Maximum security is maintained by movement limiters on the lower jaw and piston as well as the safety check valves on the hydraulic system. Hydraulic power unit works silently.0 – 40 mm round and flat samples can be tested with a user friendly hydraulic jaws that comply with all standards Strain measurement can be done by the electronic displacement transducer built in the machineor external extensometer fitted to the specimen. Load cell is used for load measurements.Strain measurements can be done directly from the extensometer fitted to the specimen. Tests can be done fully automatic by digital control unit or

computer. Machine makes the test with the set pace rate and turns to start position automatically. The distance between the grips can be set by motor driven hand set system.

8

Page 13: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Capacity

Load Measurement Accuracy

Displacement Measurement Accuracy

Columns Diameter

Vertical Test Distance

Distance Between Columns

Piston Stroke

Max Pressure

Test Space

Height

400 kN 600 kN

± %1 ± %1

0,01 mm 0,01 mm

420 mm 600 mm

200 mm 200 mm

680 x 540 780 x 600

2500 mm 2800 mm

Lower 80 mm 80 mm

Upper 70 mm 80 mm

Min 80 mm 80 mm

Max 400 mm 400 mm

Grisp

Load

Specifications UTM 3000 UTM 4000

80 mm

80 mm70 mm

60 mm

Concrete

[email protected] 9

Page 14: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Cement Flow Table EN Model

Automatic Programmable and Manual Mortar Mixer

General PropertiesUsed for determining consistency of mortar, lime and cement specimens. Manual and motorized two models are available.

The table is 300mm dia., 10mm drop height. The cone made of brass has dimensions of 100mm base dia. x 70mm top dia. x 60mm high.

Dimensions : UTCM-0038 Manual ø255x290 mmUTCM-0038/E Motorized 450x1030x330mmPower : 180 WWeight (approx.) : UTCM-0038 Manual 12.7 kgUTCM-0038/E Motorized 50 kg

General PropertiesThe mixer has been designed to mix mortars and cement pastes primarily to the requirements of standards. The mixing paddle has a planetary motion and is driven by a motor with a microprocessor based speed and program controller. The mixer can be operated either in anautomatic or manual mode. When the mixer is used in the manual mode, the two mixing speeds can be changed by mean of the rocker switch, without switching off the motor. In the automatic mode any of the preset mixing programs may be selected.

The mixing head rotates with speed of 62 and 125 r.p.m. and the beater 140 and 285 r.p.m. Automatic Sand dispenser is supplied with machine and thirty seconds after start of mixing sequence sand is automatically discharged in to the mixing bowl.

The mixer is supplied complete with 5lt capacity bowl and the beater.220 V, 50-60 Hz, 1 ph

Dimensions : 300×555×610 mm (lxwxh)Power : 250 WWeight (approx.) : 56 kg

Product Code: UTCM-0038 Cement Flow TableUTCM-0038/E Motorized Cement Flow Table

UTCM-0037/10 Flow MouldUTCM-0037/11 Tamping Rod

Standards: EN 459-2, 1015-3

Product Code: UTCM-0006 Automatic Programmable Mortar Mixer

UTCM-0005/1 Mixing Bowl 5 litersUTCM-0005/2 Beater

www.precisa.ro

Cement

10

Page 15: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Jolting Table

Curing Cabinet

Le Chatelier Water Bath

Product Code:UTCM-0012 Jolting TableUTCM-0011 40x40x160 mm Feed Hopper

Standards: EN 196-1, ISO 679

Product Code: UTCM-0013Standards: EN 196-1

Product Code: UTCM-0025/FStandards: EN 196-3, pr EN ISO 9597

Jolting table is used for mould compacting of 40x40x160 mm cement specimens and consists of mould table seated on a rotating cam driven at 60 revolutions per minute. The table drop is 15.0 mm. The machine is equipped with counter which provides automatic shut off at end of preset drop numbers.

Weight and dimensions of the jolting table fully comply with the requirements of EN 196-1 standard. Rapid mould lock and release system allows easy and quick operation.220 V, 50-60 Hz, 1 ph

Dimensions : 300x450x1030 mm (lxwxh)Power : 250 Wr.p.m. : 60Drop Height : 15 mmWeight (approx.) : 55 kg

Used for curing tests of cement specimens. The curing cabinet provides 20 ± 1°C temperature and 95% humidity for cement specimens. Internal chamber and racks are made of stainless steel. The temperature is maintained at 20±1°C by a immersion heater and refrigerator unit which are supplied complete with cabinet. The cabinet is equipped with digital unit which controlsand monitors the temperature. The humidity is maintained from 95% to saturation by water nebulisers and also monitored on digital unit.

220 V, 50-60 Hz, 1 phInternal Dimensions : 700x900x1300 mm (lxwxh)External Dimensions : 850x1200x1900 mm (lxwxh)Weight (approx.) : 250 kg

For use with Le Chatelier moulds for the determination of the soundness of cement paste. The bath is manufactured from corrosion resistant material, complete with a removable rack to hold up to twelve moulds. An adjustable controller for the immersion heater regulates the water temperature from ambient to boiling point.

220 V, 50-60 Hz, 1 ph

Weight (approx.) : 20 kg

Cement

[email protected] 11

Page 16: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Blaine Fineness Apparatus

Le Chatelier Test Set

General PropertiesUsed to determine the particle size of Portland cement, limes and similar powders expressed in terms of their specific surface. It consists of a stainless steel cell, perforated disc and plunger. A U-tube glass manometer is fitted to the steel stand. The set is complete with rubber aspirator and filter paper.

Dimensions : 170x220x470 mm (wxdxh)Weight (approx.) : 8 kg

General PropertiesThe soundness of cements and limes is determined using the expansion test with Le Chatelier moulds according to the relevant standard. The mould consists of a spring tensioned split cylinder 30 mm internal diameter x 30 mm high with two indicator stems which measure 150 mm from the points to the centre line of the cylinder and O ring.

Standard weight and glass plate are supplied complete with the mould.

Weight (approx.) : 30 gr

Product Code: UTCM-0041 Blaine Fineness ApparatusUTCM-0041/1 U Manometer Tube

UTCM-0041/2 Cell with perforated discUTCM-0041/3 Filter Paper (pack of 100)

UTCM-0041/4 Manometer Liquid Bottle 250 mmStandards: EN 196-6

Product Code: UTCM- 0025 /S Le Chatelier Test SetUTCM- 0025 Le Chatelier Mould

Standards: EN 196-3, EN ISO 9597

www.precisa.ro

Cement

12

Page 17: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Vicat Test Set

Cement Compression and Flexure Machine

Product Code:UTCM- 0028 Vicat Test Set EN ModelUTCM- 0028/A Vicat Test Set ASTM Model

UTCM- 0028/1 Vicat ApparatusUTCM- 0027/22 Vicat Mould EN Model

UTCM- 0027/23 Vicat Mould ASTM ModelUTCM- 0028/31 Initial Needle EN Model

UTCM- 0028/21 Initial Needle ASTM ModelUTCM- 0028/41 Final Needle EN Model

UTCM- 0028/5 Consistency PlungerUTCM- 0028/6 Glass Plate

Standards: EN 196-3, ASTM C187, AASHTO T129, T131

Product Code: UTCM- 6420 Cement Compression and Flexure MachineUTCM- 9030 Compression Jig Assembly for EN 196-1

UTCM- 9032 Compression Jig Assembly for ASTM C109UTCM- 0019 Flexure Jig Assembly for EN 196-1

UTCM- 0021 Flexure Jig Assembly for ASTM C109Standards: EN 196-1, ASTM C109

Used for determination of setting time and consistency of cement by Vicat Method. The test set comprises Vicat Frame, Vicat Mould, Initial and Final needles, glass plate and consistency plunger.

Dimensions : 150×190×318 mmWeight (approx.) : 3 kg

Fully Automatic cement compression machine has been designed according to the EN 196-1 and ASTM C109 standards for testing the flexure of the mortar prisms 40x40x160 mm and the compression on the 40x40mm pieces of prisms after the flexure test or 50 x50 mm mortar cubes.

The BC100 is contained in light alloy housing and its design satisfies the ergonomic requirements for various use. The BC100 digital graphic display allows real time load vs time graph. At the end of the test cycle, the results can be stored in the large memory or downloaded to a PC in UTEST software format. Dedicated software package is available for further online data processing, database management and certificate printing.

Cement

[email protected] 13

Page 18: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

The main characteristics are:

• High resolution 65.000 points• 240*120 pixel blue-white graphic LCD display• Standalone full automatic testing capacity• CPU card by microprocessor 32 bit ARM risk architecture• Can make manual tests if required• Large permanent memory up to 256 test results• RS232C (optional Ethernet) connection at 57600 band• One RS232 serial port for connecting either PC or printer for data transmission• Two analogical channels, use for Load Cell or pressure transducer• A sample type and dimensions can be entered respect to the standards• 18 key touch membrane keyboard• Easy to operate with 6 main function keys• Language select; English, Turkish, Russian• Can control two frames

The main characteristics are:

• Dual stage pump• 750 W power• 25 liter oil capacity• 60-100 mm/min fast approach speed

On both frame the load is measured by load cell to get accurate test results. Both test chambersis supplied complete with round compression platens of 165 mm diameter with 245 mm verticaldaylight.

Compression Load Speed : 2400 N/sFlexure Load Speed : 50 N/s

Model Capacity

kN ±1% from kN kN dimensions mm

Accuracy Resolution Platen

6420 15 kN / 250 kN 0,01kN / 0,01kN

Flexure/Compression 25 kN to 250 kN

2 kN to 15 kN / 165mm/165mm

Max. vertical

approx. kg

(wxdxh) mm

50 mm/50 mm 245mm/245 mm 500x1030x1600mm 250 kg0,75 W/0,75 W

daylight mmdimensions

Ram travel mm WeightOverallPower W

www.precisa.ro

Cement

14

Page 19: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

Cement

[email protected] 15

Cement Moulds

Le Chatelier Flask

Cement Flow Table ASTM Model

Product Code:UTCM-0010 40x40x160 mm Three Gang Mould 11,6 kgUTCM-0080 50x50x50 mm Three Gang Cube Mould 3,6 kg

UTCM-0051 70.7x70.7x70.7 mm Cube Mould 3,4 kgStandards: EN 196-1, ASTM C109, BS 4550

Product Code: UTCM-0003Standards: EN 196-6, ASTM C188, AASHTO T133

Product Code: UTCM-0040 Cement Flow TableUTCM-0040/E Motorized Cement Flow Table

UTCM-0040/10 Flow MouldStandards: ASTM C230

All the moulds have been manufactured from steel and all internal surfaces are machined. All dimensions and specifications comply with the related standards.The 40x40x160 mm mould has the surface hardness of minimum HV400.

Used to determine the specific gravity of hydraulic cement and lime. Glass flask 250ml capacity, with graduated neck from 0 to 1 ml and from 18 to 24 ml in 0.1 ml graduation with accuracy of 0.05 ml.

Used for determining consistency of mortar, lime and cement specimens. Manual and motorized two models are available.

Dimensions : UTCM-0040/A Manual ø255x290 mmUTCM-0040/E Motorized 450x1030x330mmPower : 180 WWeight (approx.) : UTCM-0040/A Manual 12.7 kgUTCM-0040/E Motorized 50 kg

Page 20: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

16

Abrasion Testing Machine

Shape Index Gauge

Determination of Resistance to Freezingand Thawing Climatic Chamber

220 V, 50-60 Hz, 1 ph

Weight (approx.) : 85 kg

Weight (approx.) : UTA-0542 Shape Index Gauge 0,4 kg

General PropertiesAbrasion Testing Machine is designed for determining the resistance to abrasion / wear of natural stones and concrete products. The abrasion wheel is 70 mm thick and rotates with speed of between 75 r.p.m. the machine is equipped with digital counter which stops machine at the preset number of revolutions. Supplied complete with abrasion sand.

General PropertiesUsed to determine the shape factor of aggregates.

General PropertiesUsed in determining resistance to freezing and thawing. Provides freezing / thawing in air and also freezing in air / thawing in water. The chamber equipped with programmer for 9 programs in 9 steps for each program. Time can be arranged to 999 minutes for each step of program. Temperature range for cabinet is -25°C to +60°C. The control unit is electronic and equipped with digital display with 0,1°C temperature accuracy.The temperature distribution accuracy in the cabinet is not higher than 2°C. Cabinet provides heating from -25°C to +25°C in 60 minutes.

Product Code: UTA- 0471 Abrasion Testing MachineUTA- 0472 Abrasive Sand

Standards: EN 1341, 1342, 1343

Product Code: UTA-0542 Shape Index GaugeStandards: EN 933-4, DIN 4226 CNR No.95, NLT 354

Product Code: UTA-1428Standards: EN 3449

www.precisa.ro

Agregate

Page 21: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

17

Methylene Blue Test Set

Micro-Deval Testing Machine

Product Code: UTA–0439 Methylene Blue Test SetUTA–0439/1 High Speed StirrerUTA–0439/2 Kaolinite (500 gr)

UTA–0439/3 Methylene blue (100 gr)UTA–0439/4 Filter Paper (pack of 100)

UTA–0439/5 Burette 50 mlUTA–0439/6 Plastic Beaker 3000 ml

UTA–0439/7 Glass RodStandarts: EN 933-9, NF P 94-068, UNE 83 180, UNI 8520-15

Product Code: UTA–0524Standarts: EN 1097-1, NF P18-572, P18-576, CNR No.109, UNE 83115

Software for data transfer to computer is supplied complete with the cabinet. The cabinet automatically arranges water level in reservoir. It is equipped with water pump which is used for water filling and discharging for soaking.The condenser of the cabinet is fitted with air cooled hermetic cooler. The gas used for cooler does not include CFC.

230 V, 50 Hz, 1 ph

Internal Dimensions : 500x700x550mm (lxwxh)External Dimensions : 1750x850x1100 mm (lxwxh)

Methylene Blue Test Set is used for determining clay content in the fines fraction of the aggregates. Set consists of 400/600 r.p.m. High Speed Motor and stirring propeller, 3000ml capacity plastic beaker, 100gr methylene blue, 500gr kaolinite, Filter Papers (pack of 100), glass rod, 50ml glass burette, burette holder and burette stand.

220 V, 50-60 Hz, 1 ph

Micro Deval Testing Machine used to determine the resistance to wear of 25-50mm size aggregates. The machine consists of a steel frame, four stainless steel cylinders, and 25kg of 10 mm diameter stainless steel spheres and automatic digital counter which allows machine to stop automatically at the preset number of revolutions.

Stainless steel Ø200*154 drums are rotating at speed of 100 (±5) r.p.m.

220 V, 50-60 Hz, 1 ph

Dimensions : 640x1200x350 mm (lxwxh) Power : 750W Weight (approx.) : 150 kg

Agregate

[email protected]

Page 22: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

18

Agregate

www.precisa.ro

Skid Resistance and Friction Tester (Skid Tester)

AAV Abrasion Machine

Accelerated Polishing Machine

Used for the measurement of surface friction properties, the apparatus is suitable for both site and laboratory applications and for Polished Stone Value tests using curved specimens from accelerated polishing tests. Slider lifting system integrated in the pendulum foot, which guarantees reliable adjustment operations.

Skid Tester provides following features:• Easy and reliable height adjusting system• New low friction release mechanism of the pendulum arm for better accuracy.

Dimensions : 790x760x320 mm (lxwxh)Weight : 34 kg

The test provides a measure of the resistance of aggregate to surface wear by abrasion. The abrasion machine consists of a flat circular cast iron grinding lap 600 mm dia. which rotates in a horizontal plane at a speed of 28/30 r.p.m. The abrasive sand is fed across the surface of thespecimen samples through a special funnel.

The machine is supplied complete with two specimen moulds, two trays, two flat plates, weights and clamps.

Weight : 200 kg

Used to measure the resistance of road stone to the polishing action of vehicle tires on a road surface. The machine consists of road wheel rotating in the speed of between 315 and 325 r.p.m. The electric motor of the machine is 370W and fan-cooled.

Machine supplied complete with road wheel, side plate, rubber rings, abrasive feed mechanism, corn emery, flour emery, set of 4 specimen mould and 2 mould plates.

230 V, 50 Hz, 1 phDimensions : 740x720x1520 mm (lxwxh)Weight : 175 kg

Product Code: UTA-0190Standards: EN 1097-8, ASTM E103, BS 812:144, NLT 174,

CNR No. 105, 140, NF P18-578, NF P18-575

Product Code: UTA-0522Standards: EN 1097-8, BS 812

Product Code: UTA- 0525Standards: EN 1097-8, EN 1341, 1342, 1343

Page 23: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

19

Sand Equivalent Test Set

Los Angeles(Determination of Resistance to Fragmentation)

Product Code : UTA-0050 Sand Equivalent Test Set EN ModelUTA-0050/A Sand Equivalent Test Set ASTM Model

Standards: EN 933–8, ASTM D2419, AASHTO T176, UNI 8520–15,UNE 83131, CNR No. 27

Product Code: UTA–0500 Los Angeles Abrasion MachineUTA–0500/A Los Angeles Abrasion Machine with safety cabinet

UTA–0505 Set of 12 abrasive charges conforming to ASTM UNI CNRUTA–0505/A Set of 11 abrasive charges conforming to EN

Standards: EN 1097-2, ASTM C131, C535, NF P18-573,UNE 83114, UNI 8520-19, CNR No.34

Sand Equivalent Test Set is used to determine the fines of aggregates.The Sand Equivalent Test Set comprises 4 measuring cylinders, irrigator tube, weighted foot assembly, siphon assembly, rubber stopper, funnel, rubber hose, pinch clip, 1 liters glycerol, 5 lt capacity sand jar and a carrying case.Set conforming to ASTM is same as EN Set except for Measuring Cylinders which are totally graduated.

Weight: 4,6 kg

Los Angeles Abrasion Machine is used for determination of aggregates resistance to fragmentation. The machine consists of an electronic control unit and a rolled steel drum having an inside diameter of 711 mm and internal length 508 mm. The drum is rotated at a speed ofbetween 31 and 33 r.p.m. The internal shelf is provided with the machine is conforming to ASTM and EN standards. The machine is equipped with automatic counter, which allows stopping when the preset number of revolutions is completed. There is a steel tray supplied with machine for easy discharge of specimen.

Standard model can be upgraded with safety cabinet where Los Angeles Machine will be placed. In this case electronic control unit will be installed on the safety cabinet. The cabinet is equipped with electric safety device which automatically stops the rotation of the drum when the door is opened, conforming to CE directives.

220 V, 50–60 Hz, 1 phDimensions : 1000x900x1000 mm (wxlxh)Power : 750 W

Agregate

[email protected]

Page 24: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

20

Testing Sieves

Thermometers

Utest Material Testing Equipment proposes a complete range of testing sieves. In this field we cooperate with Endecotts who is the worlds leading manufacturer of quality laboratory test sieves. The only test sieve manufacturer to meet the exacting standards of BS 410 ISO 3310/1 & 2, ASTM E.11 and accredited with the British Standard Kitemark.All test sieves are manufactured to National and International Specifications and are supplied with a “Certificate of Compliance”. Each sieve is individually serial numbered, ensuring full traceability. Endecotts sieves are made with only the highest quality materials and are availablein diameter sizes of 38, 100, 150, 200, 250, 300, 315, 350, 400 and 450mm, as well as 3,8,12 or 18 inches.Woven wire mesh sieves are available in frame materials of either brass or stainless steel with larger diameter sieves also available in plated steel.

ISO 3310-2, ISO 565, ASTM E11Standards: EN 933-2, ISO 3310-1,

Product Code:

Digital ThermometersUTG- 1226/A -50 - +150°CUTG- 1226/B -50 - +260°CUTG- 1226/C -50 - +300°C

Glass ThermometersUTG- 1199 -10 - +60°CUTG- 1199 -10 - +110°CUTG- 1199 -10 - +160°CUTG- 1199 -10 - +310°C

Dial ThermometersUTG- 1207 -30 - +60°CUTG- 1212 0 - +200°CUTG- 1213 0 - +260°CMin-Max ThermometerUTG- 1215/1 -20 - +50°CMin-Max Hygrometer, Thermometer (Digital)UTG- 2220

We propose different model digital, dial, glass and Min-Max thermometers, which cover practically all applications in the construction industry.

Agregate

www.precisa.ro

Page 25: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

21

Water Bath

Product Code:UTA- D1411/1 14 litersUTA- D1411/2 30 litersUTA- D1411/3 48 liters

Ideal for general laboratory use including Marshall tests. Internal surfaces of polished stainless steel and housed in a sheet steel insulated outer case. They are offered in different sizes. Thermostatic heat controlled baths are supplied complete with cover.

220 V, 50–60 Hz, 1ph

Muffle Furnaces are widely used for determining various properties of construction materials. Vertical lift door directs heat away from user and saves counter space. A safety interlock switch disconnects power when the door is open. Vertical lift door has maximum access with minimum head room for easy loading and unloading. Programmable models are optional.

230 V, 50-60 Hz, 1 ph

Muffle Furnace Product Code: UTA- 1207

Capacity : 7.3 litersMaximum operating temperature : 1200 CTemperature Range : 1150 CRise Time : 35 minutesInternal Dimensions : 250x200x140 mm (wxlxh)External Dimensions: 580x550x650 mm (wxlxh)Power : 220 VAC / 2 kW

Agregate

[email protected]

Page 26: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

22

U Shape Box

Digital Balances

Laboratory Hardware

General PropertiesThe U Shape Box is used to determine the confined flowability and the capacity of SCC concrete to flow within confined spaces. The box is made of galvanized steel frame consisting of four 10 mm diameter and three 13 mm diameter bars.

Dimensions : 200x280x680 mm (lxwxh)Weight (approx.) : 25 kg

General PropertiesThese precise, economical and very easy to use balances are ideal for both central and site laboratories. Available in various model, capacity and precision.

Product Code: UTC- 0147/DStandards: UNI 11044, Rilem report No. 23

Product Code: UTG- 0613/A Moisture Analyzers 0,0001 gr x 50 grUTG- 0613/B Analytical Balance 0,1 mg x 220 gr

UTG- 0630 Precision Balance 0,1 gr x 6 kgUTG- 0631/C Precision Balance 0,5 gr x 30 kg

UTG- 0648 Platform Balance 5 gr x 150kg

Product Code: Specimen TraysUTG- 1305 27x46x4 cmUTG- 1305/1 26x41x4 cmUTG- 1305/2 25x36x4 cmUTG- 1305/3 23x33x4 cmUTG- 1305/4 17x27x4 cmSpatulasUTG- 1630 SmallUTG- 1632 MediumUTG- 1633 Large

BrushesUTG- 1680 Hair BrushUTG- 1685 Wire Brush

UTG- 1673/G Double ended 3hair/ wire brush

ScoopsUTG- 1601 Small

UTG- 1602 MediumUTG- 1603 Large

Agregate

www.precisa.ro

Page 27: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

23

Laboratory Glassware

Porcelain / Mortar and Pestles

Product Code:Beaker

UTG-1071 Beaker 50 mlUTG-1072 Beaker 100 mlUTG-1073 Beaker 250 mlUTG-1074 Beaker 500 ml

UTG-1075 Beaker 1000 mlUTG-1075/1 Beaker 2000 ml

Measuring CylinderUTG–1002 Measuring Cylinder 50 ml

UTG–1003 Measuring Cylinder 100 mlUTG–1004 Measuring Cylinder 250 mlUTG–1005 Measuring Cylinder 500 ml

UTG–1006 Measuring Cylinder 1000 mlUTG–1007 Measuring Cylinder 2000 m

PycnometerUTG-1126 Pycnometer 50 ml

UTG-1126 Pycnometer 100 mlUTG-1126 Pycnometer 250 mlUTG-1126 Pycnometer 500 ml

UTG-1126 Pycnometer 1000 mlUTG-1126 Pycnometer 2000 ml

Conical Flask - ErlenmayerUTG-1030 Conical Flask - Erlenmayer 100 mlUTG-1031 Conical Flask - Erlenmeyer 300 mlUTG-1032 Conical Flask - Erlenmayer 500 ml

UTG-1033 Conical Flask - Erlenmayer 1000 mlUTG-1034 Conical Flask - Erlenmayer 2000 ml

DessicatorUTG-1110 Dessicator Ø210 mm

UTG-1110/A Dessicator Ø240 mmUTG-1111 Dessicator Ø300 mm

Product Code: UTG- 1170 Evaporating Dish Ø10 cmUTG- 1171 Evaporating Dish Ø12 cm

UTG-1180/A Porcelain Mortar and Pestle Ø12 cmUTG-1180/B Porcelain Mortar and Pestle Ø16 cm

UTG-1187 Porcelain Crucible 25 ml

Vacuum DessicatorUTG-1112 Vacuum Dessicator Ø210 mmUTG-1112/A Vacuum Dessicator Ø240 mmUTG-1113 Vacuum Dessicator Ø300 mm

Volumetric FlaskUTG-1058 Volumetric Flask 50 mlUTG-1059 Volumetric Flask 100 mlUTG-1060 Volumetric Flask 250 mlUTG-1061 Volumetric Flask 500 mlUTG-1062 Volumetric Flask 1000 mlUTG-1063 Volumetric Flask 2000 ml

A comprehensive range of laboratory glassware is available.

Agregate

[email protected]

Page 28: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

24

Sieve Shaker

Drying Oven

The sieve shaker imparts a circular motion to the material being sieved so that it makes a slow progression over the surface of the sieve. At the same time a feature of the rapid vertical movement agitates the sample which helps to clear the sieve apertures and avoid them blinding.The shaker is fitted with timer which can be pre-set for any duration up to 60 minutes.

This unit will accept 200mm and 300mm diameter sieves. Wet sieving kits in the appropriate sizes may be used with this shaker.

220 V, 50-60 Hz, 1 ph

Dimensions : UTG-0411 510×510×370 mm (wxlxh)UTG-0411/Z 510×510×370 mm (wxlxh)Weight (approx.) : UTG-0411 86 kgUTG-0411/Z 86 kg

UTG-0411/Z Frequency controlledStandards: EN 932-5, ISO 3310-1

Product Code: UTG-0411

Product Code: UTG-1390 50 liters UTG-1391 120 liters UTG-1396250 liters

UTG-1397 500 liters UTG-1398 750 litersStandards: EN 932-5, EN 1097-5,

ASTM C 127- C136-D558, D559, D560,D698, D1557, D1559, BS 1377:1-1924:11 UNE 103300

These ovens have been designed for drying asphalt, soil, rock, concrete and aggregate specimens. The models we propose are available in 50,120,250,500,750 liter capacities.Temperature range is from ambient to 250°C with precision of 1 ºC. The interior is made from stainless steel and the exterior is robustly constructed from sheet steel finished in powder coated paint. The insulated chambers are made from clad mild steel.

All units are fan circulated and fitted with direct reading digital control unit. 2,3 or 4 shelves supplied according to oven capacity.

220V / 50Hz or 380V / 50HzWeight (approx.) : UTG-1390 35 kgUTG-1391 50 kgUTG-1396 70 kgUTG-1397 100 kgUTG-1398 140 kg

Agregate

www.precisa.ro

Page 29: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

25

Vacuum Pump

Ideal for field and laboratory use to produce vacuum.

220 V, 50-60 Hz, 1 ph

Used to determine the moisture content at which clay soils pass from a plastic to a liquid state.Comprises removable brass cup, adjustable crank and cam mechanism, blow counter, and base. Two versions available: hand operated and motor operated. Supplied complete with grooving tool according to the reference standard. The grooving tool has to be ordered separately.

Casagrande Product Code: UTS- 0030/E Hand Operated Liquid Limit Device BS1377:2UTS- 0030/F Hand Operated Liquid Limit Device ASTM D4318

UTS- 0031/E Motorized Liquid Limit Device BS1377:2UTS- 0031/F Motorized Liquid Limit Device ASTM D4318

UTS- 0032/P Plastic Grooving Tool BS1377:2UTS- 0032/AP Plastic Grooving Tool ASTM D4318

UTS- 0032/A Metal Grooving Tool ASTM D4318UTS- 0033 Brass Grooving Tool UNI 10014

Standards: ASTM D4318, BS 1377:2, UNE 7377, 7002, UNI 10014

For the on site determination of the degree of compaction. Complete set includes double cone, plastic sand jar 5lt capacity and metal tray.

Sand Cone Density Set Product Code: UTS -0129 Sand Cone Set 6.5”UTS-0133 Sand Cone Set 12”

UTS-0130/2 Plastic Sand Jar 5 ltStandards: ASTM D1556, AASHTO T191

Agregate

[email protected]

Page 30: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

26

Sand Equivalent Shaker

Flakiness Sieves

Stroke Travel : 200mm ± 1mm (EN)203.2mm ± 1.02mm (ASTM)Rate : 180mm ± 2/min (EN)175mm ± 2/min (ASTM)Dimensions : UTA–0056 220x600x320 mm (wxlxh) Weight: 24,7 kgUTA–0056/A 240x800x340 mm (wxlxh) Weight: 27,5 kg

Stroke Travel : 200mm ± 1mm (EN)203.2mm ± 1.02mm (ASTM)Rate : 180mm ± 2/min (EN)175mm ± 2/min (ASTM)Dimensions : UTA–0056 220x600x320 mm (wxlxh) Weight: 24,7 kgUTA–0056/A 240x800x340 mm (wxlxh) Weight: 27,5 kg

General PropertiesThe shaker is used for uniform shaking of Sand Equivalent Measuring Cylinders. Provides shaking action at the specified rate and stroke. Supplied complete with built in timer.

220V, 50–60 Hz, 1 ph

General PropertiesUsed to determine particle size shape or geometrical characteristics of the aggregates. Each sieve made from heavy gauge steel sheets in dimensions specified in the standards and coated with electrostatic paint.

Product Code: UTA-0056 Sand Equivalent ShakerUTA-0056/A Sand Equivalent Shaker with safety cover

Standards: EN 933–8, ASTM D2419, AASHTO T176, UNI 8520–15,UNE 83131, CNR No. 27

Product Code: UTA-0415/1, UTA-0415/2, UTA-0415/3, UTA-0415/4, UTA-0415/5, UTA-0415/6, UTA-0415/7

Standards: BS 812

UTA-0415/1 4.9 mm slot size 1.6 kg 320x195x30mm

UTA-0415/2 7.2 mm slot size 1.7 kg 340x215x40mm

UTA-0415/3 10.2 mm slot size 1.8 kg 360x235x50mm

UTA-0415/4 14.4 mm slot size 2.0 kg 380x255x60mm

UTA-0415/5 19.7 mm slot size 2.1 kg 400x275x70mm

UTA-0415/6 26.3 mm slot size 2.6 kg 420x295x80mm

UTA-0415/7 33.9 mm slot size 3.1 kg 470x330x100mm

Product Code Slot Size Weight Dimensions

www.precisa.ro

Agregate

Page 31: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

27

Grid Sieves Product Code : UTA-0418/1 UTA-0418/2 UTA-0418/3 UTA-0418/4

UTA-0418/5 UTA-0418/6 UTA-0418/7 UTA-0418/8UTA-0418/9 UTA-0418/10 UTA-0418/11 UTA-0418/12 UTA-0418/13

Standards: EN 933-1, NF P18-561, UNI 8520, NLT 354

Used to determine the flakiness index of the aggregates. Consists of electrostatic painted frame and 5 mm diameter stainless steel bars.

Dimensions : 380x320x80 mm

Product Code Aperture (mm) Weight (kg)

UTA-0418/1 2,5 3,3 kg

UTA-0418/2 3.15 3.3 kg

UTA-0418/3 4 3.8 kg

UTA-0418/4 5 3.8 kg

UTA-0418/5 6.30 3.7 kg

UTA-0418/6 8 3.6 kg

UTA-0418/7 10 3.4 kg

Product Code Aperture (mm) Weight (kg)

UTA-0418/8 12.5 3.2 kg

UTA-0418/9 16 4 kg

UTA-0418/10 20 3.2 kg

UTA-0418/11 25 3.2 kg

UTA-0418/12 31.5 2.9 kg

UTA-0418/13 40 2.7 kg

Agregate

[email protected]

Automatic Soil Compactor Product Code: UTS -8502 Automatic Soil CompactorUTS -8502/1 ASTM Rammer

UTS -8502/2 EN RammerStandards: EN 13286-2, EN 13286-47, ASTM D698, D1557,

AASHTO T99, T180, T193, BS 1377–4, 1990

The Automatic Soil Compactors is designed to provide a fully automatic uniform compaction of Standard / Modified and CBR specimens assuring conformity with the reference standard.Compactor is equipped with programmable digital counter which allows machine to stop at the preset numbers

of blows. The height and weight of the rammer is adjustable to suit test requirements. The drop weight is adjustable to 300 mm drop height and is also adjustable to 450 mm drop height. The rammer is circular faced with a 50 mm diameter and is adjustable to 2.5 kg. or 4.5 kg.An automatic blow pattern ensures effective compaction for each layer of soil and the rammer travels across the mould. The table rotates the mould in equal steps and the number of blows per layer can be set at the beginning of the test by the digital counter. User defined blow number and in-out distribution is also available.A standard proctor / CBR switch, emergency stop and start push buttons are located beside the blow counter. 220 V, 50-60 Hz, 1 ph

Drop Height : 300 mm, 305 mm, 450 mm, 457 mm (adjustable)Rammer Weight : 2.5 kg , 4.5 kgDimensions : 640x340x1506 mm (wxlxh)Power : 370 WWeight (approx.) : 135 kg

Page 32: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

28

Sand Replacement Test Set

Standard / Modified ProctorMould and Rammer

For the on site determination of the degree of compaction. Complete set consists of pouring cylinder, calibration container and tray. The sand pouring cylinder is made of cast aluminium and precisely machined; the calibration container and tray are made of plated sheet steel. The testset is available in three different sizes.

UTS -0125 Sand Replacement Test Set 100 mmUTS -0126 Sand Replacement Test Set 150 mmUTS -0127 Sand Replacement Test Set 200 mm

Standards: BS 1377:9, 1924:2

Product Code:

Product Code: UTS -0070 Standard Proctor MouldUTS -0071 Modified Proctor Mould

UTS -0076 Standard Proctor RammerUTS -0077 Modified Proctor Rammer

Standards:ASTM D558, D698, D1557, AASHTO T99, T134, T180

Moulds are used for determining the relationship between the moisture content and density of compacted soil. Made of plated steel, includes collar, mould body and base plate.

Rammers are used to compact the soil sample in the Proctor Moulds. Made of plated steel. Guide sleeve with vent holes.

Different models are available conforming to the relevant standards.

Product

Code

UTS -0070 Standard Proctor Mould 101.6 ------------- 175 4,3

UTS -0071 Modified Proctor Mould 152.4 ------------- 175 7

UTS -0076 Standard Proctor Rammer ----------- 50,8 538 4,36

UTS -0077 Modified Proctor Rammer ----------- 50,8 805 7,55

DescriptionInt. dia.

mm

Rammer dia.

mm

Height

mm

Weight

kg

Agregate

www.precisa.ro

Page 33: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

29

Asphalt

[email protected]

Marshall Stability Machine

Data Acquisition And Control System

Product Code: UTAS-0038 Marshall Stability MachineUTAS-0033 Breaking Head 100 mm

UTAS-0033/C Breaking Head 150 mmUTAS-0078 Indirect tensile assembly 100 mm

Standards: EN 12697-12, EN 12697-23, EN 12697-34

The Marshall Stability Test Machine is used to determine the load and flow values of bituminous mixtures. The UTAS-0038 is composed by a robust and compact two column frame with adjustable upper cross beam driven by an electromechanical ram with a maximum capacity of 50 kN and a data acquisition and processing system.The machine can be hand operated by a lateral hand wheel for calibration purposes. The mechanical jack raises the lower cross beam at a constant speed of 50,8 mm/min. The limit switches are provided for the both, bottom and top limit of travel. The measuring system consists of a 50 kN capacity strain gauge load cell is fitted to the upper cross beam to read stability values and 25 mm x 0.001 mm displacement transducer fitted to the Breaking Head.

LCD graphics data acquisition and controls system BC100 is designed to control the machine and to process the data from linear potentiometric transducers, Load Cells, installed on the CBR machine frame. The BC100 is contained in a light alloy housing and its design satisfies the ergonomicrequirements for various use. The BC100 digital graphic display allows real time flow / stability graph and value readout. At the end of the test cycle the results can be stored in the large memory or to a PC by using UTEST Marshall software. Dedicated real time Marshall software package is available for testing and further data processing, database management and certificate printing.

The main characteristics are:• High resolution: 65.000 points• Large permanent memory up to 100 test results• RS232C (optional Ethernet) connection at 57600 band• Language select; English, Turkish, Russian• CPU card by microprocessor 32 bit ARM risk architecture• One RS232 serial port for connecting either PC or printer for data transmission• Two analogical channels, one for Load Cell and one for Linear potentiometric transducer• Blue-white graphical display• 18 key touch membrane keyboard• 6 main function keys

50 kN Load Cell, flow transducer, breaking head, calibration handle, RS232 cable and PC software are supplied complete with the machine. 220 V, 50–60 Hz, 1 phDimensions : 470x610x950 mm (wxlxh)Power : 1100 WWeight (approx.) : 88.5 kg

Page 34: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

30

Asphalt Mixer (10lt)

Bitumen Penetrometer

The 10 liter capacity mixer is designed for mixing of samples to be used for mechanical tests as for example compaction, indirect tensile, Marshall etc. The bituminous mix must be prepared at prescribed temperature for this reason the mixer can equipped with thermostatically controlled heater. The mixing head rotates in the 11 different speed positions from 10 to 240 r.p.m. and the beater from 20 to 480 r.p.m. The user can choose speeds easily by using switch fitted to the machine. The mixer is made of stainless steel and supplied complete with 10lt capacity bowl and the beater.

Isomantle heater should be ordered separately. 220 V, 50-60 Hz, 1 phDimensions : UTAS-0072 650×600×380 mm (w×l×h)Weight : 100 kg

Used for determination of penetration of bituminous samples under constant load, time and heat.The penetrometer consists of cast iron base with levelling screws, digital penetration measurement gauge 0.01 mm precision - Release button - Automatic zeroing. Needle, transfer dish and penetration moulds are supplied complete with the apparatus. The number of penetration tins can be increased upon to request.

220 V, 50-60 Hz, 1 phWeight (approx.) : UTAS-0101 9,7 kg

Product Code: UTAS-0072 Asphalt Mixer 10 liter capacityUTAS-0072/H Isomantle Heater for 10 liter capacity mixer

UTAS-0072/1 Mixing Bowl 10 lt.UTAS-0072/2 Mixing Whisk

Standards: EN 12697-35

Product Code: UTAS-0101 Semi Automatic Penetrometer UTAS-0113 Penetration Needle; UTAS-0109 Transfer Dish; UTAS-0110 Penetration Tin

Standards: EN 1426, ASTM D5, AASHTO T 49

Asphalt

www.precisa.ro

Asphalt Mixer (5lt)

Product Code: UTAS-0005 Asphalt Mixer 5 liter capacityUTAS-0005/H Isomantle Heater for 5 liter capacity mixer

UTAS-0005/1 Mixing Bowl 5 lt.UTAS-0005/2 Mixing Whisk

Standards: EN 12697-35

The 5 liter capacity mixer is designed for mixing of samples to be used for mechanical tests as for example compaction, indirect tensile, Marshall etc. The bituminous mix must be prepared at prescribed temperature for this reason the mixer can equipped with thermostatically controlled heater. The mixing head rotates in the speed of 62 and 125 r.p.m. and the beater 140 and 285 r.p.m. The user can choose speeds easily by using switch fitted to the machine. The mixer is supplied complete with 5lt capacity bowl and the beater. Isomantle heater should be ordered separately.

220 V, 50-60 Hz, 1 ph

Dimensions : UTAS-0005 300×555×610 mm (w×l×h)Weight : 54 kg

Page 35: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

31

Ductility Testing Machine

Softening Point (Ring and Ball) Apparatus

Product Code:UTAS -0140 Ductility Testing MachineUTAS-2030 Ductility Testing Machine with Cooling Machine

UTAS-0141 Ductility MouldUTAS-0142 Ductility Mould Plate

Standards: EN 13398, ASTM D113, AASHTO T51, NF T66-006, NLT 126

Product Code: UTAS-0145 Ring and Ball ApparatusUTAS-0145/C Hot Plate with Magnetic Stirrer

UTAS-0145/1 RingUTAS-0145/2 Steel Ball

UTAS-0145/3 Ball centering guideUTAS-0145/4 Glass BeakerUTAS-1200/1 Thermometer

Standards: EN 1427, ASTM D36, AASHTO T 53

The device is used for determining the ductility of bituminous materials by measuring the elongation of briquette mould with molten bitumen in it. It is designed for testing 3 specimens simultaneously. Internal tank is made of stainless steel. The bath is fitted with an immersion heater in order to obtain, in normal conditions, the 25°C test temperature using, as stabilizing element, the cold water circulation in the stainless steel interspace.Comprises digital control unit and circulator to maintain the homogenous water temperature. The device is supplied complete with 3 sample preparation plates and 3 briquette moulds. The cooling unit can be ordered separately.220 V, 50-60 Hz, 1 ph

Dimensions : 360x2150x340 mm (wxlxh)Power : 350WWeight (approx.) : 150kg

Used for determining softening point of bituminous materials by ring and ball method. Softening Point (Ring and Ball) Apparatus comprises hotplate with magnetic stirrer, 2 steel balls, ball centering guide, 2 rings, glass vessel and thermometer.220 V, 50–60 Hz, 1 ph

220 V, 50-60 Hz, 1 phWeight (approx.) : 4,5 kg

Asphalt

[email protected]

Page 36: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

32

Loss on Heating Oven (TFOT)

"Vialit Plate" Adhesion Test Apparatus

Core Drilling Machine

Test method is used for determining the loss in mass, the effect of heat and air on a film of semisolid bituminous materials. Loss on Heating / Thin Film Oven is supplied complete with rotating shelf and 9 sample containers.

220 V, 50–60 Hz, 1 ph

Internal Dimensions : 350x350x500 mm (wxlxh)External Dimensions : 690x410x660 mm (wxlxh)Power : 40 WWeight (approx.) : 38 kg

General Properties“Vialit plate” adhesion test apparatus is used to assess the adhesion property of aggregates tobitumen. The apparatus consists of a metal basement with three vertical pointed rods to hold thetest plate; vertical rod 50 cm high with a shot at the upper end for the steel ball to drop; a 512 gsteel ball; 6 metal test plates, hand operated rubber lined roller with lead shots ballast.

Weight : 40 kg

General PropertiesThe compact and portable core drilling machine is designed to cut cores up to 150 mm diameter from concrete, asphalt and similar hard construction material. The machine comprises a vertical support column which carries the drill head/motor assembly. The motor assembly comprises 3 Hp petrol engine. A ball screw mechanism enables close control over drilling pressure and rapid return when drilling is completed. Water spraying assembly is mounted on the machine.The complete assembly supplied on a rigid wheel mounted metal base frame with leveling and fixing facility during the operation.

Core Bits should be ordered separately.

Weight (approx.) : 80 kg

Product Code: UTAS -0160 Loss on Heating OvenUTAS–0160/1 Sample container

Standards: EN 12607-2, EN 13303, ASTM D6, D1754, AASHTO T47,T179, BS 2000, CNR No.50, UNE 7110, NF T66-011

Product Code: UTAS- B0178/AStandards: EN 12272-3, NF P98-274-1

Product Code: UTAS -0202 Core Drill with petrol engineUTAS–0202/1 Coring Bit 50mm dia;

UTAS–0202/2 Coring Bit 100mm dia.UTAS–0202/3 Coring Bit 150mm dia.

Standards: EN 12697-27

Asphalt

www.precisa.ro

Page 37: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

33

Centrifuge Extractor

Manual Marshall Hammer Assembly Automatic Marshall Compactor

Product Code:UTAS-2212 Centrifuge Extractor 1500 gr. capacityUTAS-0022/1 Filter Paper for 1500 gr.

UTAS-2312 Centrifuge Extractor 3000 gr. capacityUTAS-0023/1 Filter Paper for 3000 gr.

Standards: EN 12697-1, ASTM D2172, AASHTO T164A

Product Code:UTAS-4012 Automatic Marshall CompactorStandards: EN 12697-10, 12697-30

The centrifuges are used for the determination of bitumen percentage in bituminous mixtures. All models comprise a removable precision-machined rotor bowl housed in a cylindrical aluminium box. They are driven by an electric motor fitted with AC drive (inverter) with the double function of speed control up to 3600 r.p.m. regardless of the frequency (50 or 60 Hz) and electrical braking.The rotating unit is suspended on the base by four calibrated springs, which assure a perfect stability all over the test. The cover is precisely machined and fitted with solvent resistant gasket to avoid leakages.The control panel includes: Start/Stop button, speed control knob.The Centrifuge Extractor is available in two, 1500 g and 3000 g capacity models. The apparatus is supplied complete with 100 filter papers.

220 V, 50–60 Hz, 1 ph

This automatic compactor provides a consistent and even degree of compaction.The unit incorporates a compaction pedestal, comprising a laminated hardwood block secured to a concrete base by a 300 mm square x 25 mm thick steel plate. The mechanism lifts the 4550 g ±20 g hammer and automatically releases it at the specified height of 460mm ±3mm.The conveniently positioned control fascia panel comprises of a mains light, start and stop buttons and a direct reading counter used to set the required number of blows. Dual rammer pick-ups have been incorporated reducing stress on the machine's internal mechanism.

Particular attention has been paid to operator safety by the inclusion of various in-built safety features.

Dimensions : 550x550x1950 mm (wxlxh)Power : 370 WWeight (approx.) : 224 kg

Asphalt

[email protected]

Page 38: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

34

Saybolt Viscometer

General PropertiesViscometer is 2 sample testing capacity with digital display. The apparatus is supplied complete with viscosity tube, thermometer set and 2 saybolt viscosity flasks.220 V, 50–60 Hz, 1 ph

Dimensions : 260x420x500 mm (wxlxh)Power : 500 WWeight (approx.) : 10 kg

Product Code: UTAS-0121 Saybolt ViscometerUTAS-0125/T Set of Glass Thermometers, 6 pcs.(19-27C, 34-42C, 49-57C, 57-65C, 79-87C, 95-103C)UTAS-0125/1 Saybolt Viskosity Flask 60 mlStandarts: ASTM D88, AASHTO T72

Marshall Mould

Universal Extruder

Product Code:UTAS-0057 Marshall Mould (Base plate, mould body, filling collar)

To produce the Marshall specimens with automatic or hand compactors. Comprising base plate, mould body and collar.

Weight (approx.) : 4kg

Page 39: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009

IASI

Contact

Page 40: PRECISA CATALOG ECHIPAMENTE TESTARE MATERIALE DE CONSTRUCTII  2009