53
PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering • Wall Paneling • Plastic Laminate Wall Covering • Ceiling

PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Embed Size (px)

Citation preview

Page 1: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

PowerPoint® PresentationPowerPoint® Presentation

Unit 58Unit 58Interior Wall and Ceiling FinishInterior Wall and Ceiling Finish

Gypsum Board Wallcovering • Wall Paneling • Plastic Laminate Wall

Covering • Ceiling

Gypsum Board Wallcovering • Wall Paneling • Plastic Laminate Wall

Covering • Ceiling

Page 2: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Gypsum board is fastened directly to wood or metal framing members and provides a smooth surface for paint or wallcoverings.

Gypsum board is fastened directly to wood or metal framing members and provides a smooth surface for paint or wallcoverings.

Page 3: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Gypsum boards have different edge shapes depending on their purpose.

Gypsum boards have different edge shapes depending on their purpose.

Page 4: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Gypsum board is cut by scoring it on the face side and then snapping off the waste piece.

Gypsum board is cut by scoring it on the face side and then snapping off the waste piece.

Page 5: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Jagged gypsum board edges can be smoothed with a serrated-blade forming tool.

Jagged gypsum board edges can be smoothed with a serrated-blade forming tool.

Page 6: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

In single-ply application, only one layer of gypsum board is used.

In single-ply application, only one layer of gypsum board is used.

Page 7: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

In double-ply application, an adhesive is used to bond the second layer of gypsum board to the base layer. The second layer runs at a right angle to the base layer.

In double-ply application, an adhesive is used to bond the second layer of gypsum board to the base layer. The second layer runs at a right angle to the base layer.

Page 8: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

A metal foot lift is used to raise a gypsum board wall panel up tightly against the ceiling. The space below the panel is covered by base molding.

A metal foot lift is used to raise a gypsum board wall panel up tightly against the ceiling. The space below the panel is covered by base molding.

Page 9: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Nails may be used to fasten gypsum board to wood framing members. Small-headed nails are used with predecorated panels.

Nails may be used to fasten gypsum board to wood framing members. Small-headed nails are used with predecorated panels.

Page 10: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Nails must be driven properly to ensure a solid connection between the gypsum board and wood framing member. Nails driven too deeply, or at an angle, will cut through the face covering.

Nails must be driven properly to ensure a solid connection between the gypsum board and wood framing member. Nails driven too deeply, or at an angle, will cut through the face covering.

Page 11: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Loose nails are caused by a poor fit of the gypsum board to the framing surface or by nails missing the framing members.

Loose nails are caused by a poor fit of the gypsum board to the framing surface or by nails missing the framing members.

Page 12: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

The proper single-nailing pattern ensures a sound connection between the gypsum board and wood framing member. Nailing should begin at the center of the panel and move outward.

The proper single-nailing pattern ensures a sound connection between the gypsum board and wood framing member. Nailing should begin at the center of the panel and move outward.

Page 13: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When double-nailing gypsum board, the second set of nails may be driven after the first set is driven across the entire panel, or the second set of nails in each row may be driven after the first set in each row is driven. Nailing should begin at the center of the panel and move outward.

When double-nailing gypsum board, the second set of nails may be driven after the first set is driven across the entire panel, or the second set of nails in each row may be driven after the first set in each row is driven. Nailing should begin at the center of the panel and move outward.

Page 14: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Screws may be used to fasten gypsum board to metal or wood framing members. A drywall screwdriver is used to drive the screws.

Screws may be used to fasten gypsum board to metal or wood framing members. A drywall screwdriver is used to drive the screws.

Page 15: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Stud adhesive is used with screws or nails to fasten single-ply gypsum board to wood or metal framing members.

Stud adhesive is used with screws or nails to fasten single-ply gypsum board to wood or metal framing members.

Page 16: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Gypsum board must be properly finished to ensure a smooth and even surface.

Gypsum board must be properly finished to ensure a smooth and even surface.

Page 17: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Metal corner beads reinforce outside corners of gypsum board.

Metal corner beads reinforce outside corners of gypsum board.

Page 18: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Molding is used to cover joints and corners of predecorated gypsum board.

Molding is used to cover joints and corners of predecorated gypsum board.

Page 19: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Grooved softwood-veneer plywood wall panels create pleasant shadow lines.

Grooved softwood-veneer plywood wall panels create pleasant shadow lines.

Page 20: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Wall paneling may have rabbeted or beveled edges, forming channel or V-joints respectively.

Wall paneling may have rabbeted or beveled edges, forming channel or V-joints respectively.

Page 21: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Plywood panels are stacked with wood strips between them for preconditioning to room temperature.

Plywood panels are stacked with wood strips between them for preconditioning to room temperature.

Page 22: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Furring strips are installed over existing uneven walls to provide a smooth and even wall surface for plywood or hardboard panels.

Furring strips are installed over existing uneven walls to provide a smooth and even wall surface for plywood or hardboard panels.

Page 23: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Panels can be positioned so that a continuous joint occurs on each side of the door or so joints break over the openings.

Panels can be positioned so that a continuous joint occurs on each side of the door or so joints break over the openings.

Page 24: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Holes for electrical outlets and other openings must be laid out before the panel is set in place. The openings may be cut before or after the panel is positioned using a cutout saw.

Holes for electrical outlets and other openings must be laid out before the panel is set in place. The openings may be cut before or after the panel is positioned using a cutout saw.

Page 25: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

The item requiring an opening—in this case an electrical box—is used as a pattern for marking a panel opening.

The item requiring an opening—in this case an electrical box—is used as a pattern for marking a panel opening.

Page 26: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When installing wall panels over stud walls, the edges of the panels must fall over the centers of the studs.

When installing wall panels over stud walls, the edges of the panels must fall over the centers of the studs.

Page 27: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Base and ceiling moldings eliminate the need to scribe the top and bottom panel.

Base and ceiling moldings eliminate the need to scribe the top and bottom panel.

Page 28: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Molding is often used to cover the inside and outside corners of interior paneling.Molding is often used to cover the inside and outside corners of interior paneling.

Page 29: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

A panel must be carefully scribed to the other wall when no molding covers the inside corner.

A panel must be carefully scribed to the other wall when no molding covers the inside corner.

Page 30: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Wall panels may be mitered if molding is not used on an outside corner.

Wall panels may be mitered if molding is not used on an outside corner.

Page 31: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Flush application of panels on outside corners is easier than mitering and panel edges are less susceptible to damage.

Flush application of panels on outside corners is easier than mitering and panel edges are less susceptible to damage.

Page 32: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Nails are less noticeable when driven along the bevel or into the grooves of a panel.

Nails are less noticeable when driven along the bevel or into the grooves of a panel.

Page 33: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Adhesive is applied in 3″ long beads, 6″ apart, at intermediate studs or at furring strips behind the panel.

Adhesive is applied in 3″ long beads, 6″ apart, at intermediate studs or at furring strips behind the panel.

Page 34: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

A wall panel is pressed into place after the adhesive has been applied.

A wall panel is pressed into place after the adhesive has been applied.

Page 35: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

After the panel has been pressed against the adhesive, it is grasped at the bottom along both edges and slowly pulled away from the stud. The panel is then pressed back into position after 2 min.

After the panel has been pressed against the adhesive, it is grasped at the bottom along both edges and slowly pulled away from the stud. The panel is then pressed back into position after 2 min.

Page 36: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Solid board paneling may be applied horizontally.Solid board paneling may be applied horizontally.

Page 37: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When installing board-on-board wall paneling, drive an 8d nail at the center of the underboard. The top boards should overlap the underboard a minimum of 1″. Fasten the top board with two 10d nails. Make sure the nails clear the underboard to allow for expansion and contraction.

When installing board-on-board wall paneling, drive an 8d nail at the center of the underboard. The top boards should overlap the underboard a minimum of 1″. Fasten the top board with two 10d nails. Make sure the nails clear the underboard to allow for expansion and contraction.

Page 38: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When installing board-and-batten wall paneling, drive an 8d nail at the center of the underboard. The underboards are spaced approximately 1/2″ apart. Drive a 10d nail through the center of the batten.

When installing board-and-batten wall paneling, drive an 8d nail at the center of the underboard. The underboards are spaced approximately 1/2″ apart. Drive a 10d nail through the center of the batten.

Page 39: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When installing tongue-and-groove wall paneling, 4″ and 6″ widths can be blind-nailed with 6d finish nails driven at a 45° angle. This method eliminates the need to countersink and putty face nails.

When installing tongue-and-groove wall paneling, 4″ and 6″ widths can be blind-nailed with 6d finish nails driven at a 45° angle. This method eliminates the need to countersink and putty face nails.

Page 40: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When installing channel-rustic solid board paneling up to 6″ wide, one face nail is adequate to secure the board. Widths over 8″ require a face nail at the center of each board.

When installing channel-rustic solid board paneling up to 6″ wide, one face nail is adequate to secure the board. Widths over 8″ require a face nail at the center of each board.

Page 41: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Blocking must be placed in a stud wall to provide a nailing base for vertical board paneling.

Blocking must be placed in a stud wall to provide a nailing base for vertical board paneling.

Page 42: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Prior to installation, solid board paneling is arranged along the wall so wood grain and other features can be matched to each other.

Prior to installation, solid board paneling is arranged along the wall so wood grain and other features can be matched to each other.

Page 43: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

When tapping a board panel into place, use a piece of material with a grooved edge against the board to avoid damaging the edge.

When tapping a board panel into place, use a piece of material with a grooved edge against the board to avoid damaging the edge.

Page 44: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Plastic laminate wall panels are available with an imitation wood grain finish.

Plastic laminate wall panels are available with an imitation wood grain finish.

Page 45: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Suspended tile ceiling systems are frequently used in commercial construction.

Suspended tile ceiling systems are frequently used in commercial construction.

Page 46: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Ceiling tile with tongue-and-groove edges are stapled through the wide flanges into the furring strips.

Ceiling tile with tongue-and-groove edges are stapled through the wide flanges into the furring strips.

Page 47: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

For a ceiling with even-foot dimensions, the center tiles are positioned at each side of the centerlines.

For a ceiling with even-foot dimensions, the center tiles are positioned at each side of the centerlines.

Page 48: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

For a ceiling with odd-foot dimensions, the center tiles are positioned so the centerlines align with the middle of the tiles.

For a ceiling with odd-foot dimensions, the center tiles are positioned so the centerlines align with the middle of the tiles.

Page 49: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Border tiles on opposite sides of the ceiling should be the same width, and should be at least 6″ wide.

Border tiles on opposite sides of the ceiling should be the same width, and should be at least 6″ wide.

Page 50: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Suspended ceilings are often installed in commercial buildings.Suspended ceilings are often installed in commercial buildings.

Page 51: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

Recessed lighting can be used with suspended ceilings. Plumbing, lighting, and ventilation fixtures must be properly secured to structural members above a suspended ceiling.

Recessed lighting can be used with suspended ceilings. Plumbing, lighting, and ventilation fixtures must be properly secured to structural members above a suspended ceiling.

Page 52: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

A laser level is commonly used to establish the suspended ceiling height at several locations along the wall.

A laser level is commonly used to establish the suspended ceiling height at several locations along the wall.

Page 53: PowerPoint ® Presentation Unit 58 Interior Wall and Ceiling Finish Gypsum Board Wallcovering Wall Paneling Plastic Laminate Wall Covering Ceiling

Unit 58 — Interior Wall and Ceiling FinishUnit 58 — Interior Wall and Ceiling Finish

A suspended ceiling framework consists of main runners and cross tees, which are supported by hanger wires. Ceiling tile panels are supported by the runners and cross tees.

A suspended ceiling framework consists of main runners and cross tees, which are supported by hanger wires. Ceiling tile panels are supported by the runners and cross tees.