Powder Coating Resins and Additives - Home- SYNTHOMER · 3 Powder Coatings Easy to use, minimal VOC and cost effective, powder coating has emerged in recent decades as a most desirable

www.synthomer.com

Powder Coating Resins and Additives

3

Powder Coatings Easy to use, minimal VOC and cost effective, powder coating has emerged in recent decades as a most desirable method for protecting various substrates. Its high transfer efficiency and largely recoverable overspray make powder coating especially suitable for three-dimensional shapes, such as aluminum window frames, household appliances and transportation components. By producing our powder resins in Europe, Synthomer satisfies the needs of its global and regional customer base. Our broad range of powder resin options can be tailor-formulated to meet manufacturers’ performance and regulatory criteria. Our products are available either for tribo/gas oven and organo tin free upon specific request.

Synthomer line of Albester™ resins features both carboxyl and hydroxyl-terminated polyester resins. Carboxyl-terminated polyester resins offer polymers for Indoor (hybrid systems) and Outdoor applications (standard and superdurable). Hydroxyl-terminated polyester resins are designed for use in non-emitting polyester- urethane systems for special-effect architectural, anti-graffiti and transportation applications.

Albecor™ resins are our newest polyester powder-coating products, specifically designed for low thermal curing.

The lower temperature cure facilitated by Albecor powder coating resins increases energy efficiency and allow the application on heat sensitive subtrates.

Synthomer produces Albester SilkyMatt™ resins, a full range spec i-fically designed for low gloss applications. The fruit of over 25 years of experience in low gloss research and development, Albester SilkyMatt resins are the ultimate for quality and consistency in low gloss powder coatings.

The Products You Need

The products listed in this guide are just a representative selection from Synthomer’s broad portfolio. Building on this portfolio, our highly experienced R&D and technical service specialists will help address your toughest coating challenges.

We are committed to meeting your requirements as quickly and completely as possible. For more information, contact your Sales or Business Development Representative.

Innovation You Can Trust

Albester™ Resins 2 – – – Hybrid – Polyesters

Albester™ / Albester SilkyMatt™ Resins 3 – – – Hydroxyl Polyesters

Albester™ / Albester SilkyMatt™ Resins 5 – – – Outdoor durable Polyesters

Albester™ / Albester SilkyMatt™ Resins 6 – – – Superdurable Polyesters

Albemast™ Resins 9 – – – Masterbatches

Albecor™ Resins 1 – – – Low Thermally cured resins – Outdoor durable

Albecor™ Resins 4 – – – Low Thermally cured resins – Indoor applications

0 Standard Resin

1 Tribo Resin

Coding System

Organo tin free version is available upon request.

4

Standard durability – High gloss

Product Acid Value (mg KOH/g)

Viscosity (mPa·s) Cone & Plate at 200 °C

approx. Tg (°C )

Baking Schedule

Performance Characteristics

Albecor 1590 46 – 52 3000 – 5000 57 25 – 30 min at 140 °C

Specifically designed for low temperature cure applications starting from 140 °C, in 93:7 ß-HAA ratio. It combines very good reactivity along with excellent weathering and blooming resistance. Possible uses are on Architectural, parts of heavy mass, ACE, earth moving equipment.

Albecor 1595 46 – 52 3500 – 4500 56 25 – 30 min at 140 °C

Specifically designed for low temperature cure applications starting from 140 °C, in 93:7 ß-HAA ratio. It combines excellent reactivity along with good weathering and blooming resistance. Possible uses can be on heavy mass, ACE, earth moving equipment.

Superdurable – High gloss

Albecor 6190 47 – 54 1800 – 3000 57 10 – 15 min at 160 °C

Designed to give a superior exterior durability and considerably improved mechanical properties along with excellent flow compared to standard superdurable systems in 93:7 ratio. Good storage stability. Suitable for GSB Master and Qualicoat Class 2 approvals.

Albecor 6171 48 – 54 1800 – 3000 54 10 – 15 min at 160°C

Designed to give a superior exterior durability and considerably improved mechanical properties along with excellent flow compared to standard su-perdurable systems in 93:7 ratio. Improved flexibility compared to Albecor 6190. Suitable for GSB Master and Qualicoat Class 2 approvals.

Standard durability – Low gloss

Albecor 1420 16 – 20 6800 – 8200 58 15 min at 160°C

Designed for applications starting from 160 °C, in 97:3 ß-HAA ratio, to achieve mat finishing by dry blending with coatings based on Albecor 1450. Improved blooming and storage stability.

Albecor 1550 18 – 22 6000 – 7000 52 15 min at 160 °C

Designed for applications starting from 160 °C, in 97:3 ß-HAA ratio, to achieve mat finishing by dry blending with coatings based on Albecor 1560.

Albecor 1450 47 – 53 3500 – 4500 57 10 min at 160 °C

Designed for applications at 93:7 ratio with ß-HAA. It could be used in dry-blend with Albecor 1420 to produce low gloss finishing. Improved blooming and storage stability.

Albecor 1560 48 – 54 3500 – 4500 52 10 min at 160 °C

Designed for applications at 93:7 ratio with ß-HAA. It could be used in dry-blend with Albecor 1550 to produce low gloss finishing.

Albecor 1580 68 – 78 1800 – 3000 56 10 min at 160 °C

Designed for very low gloss in dry-blend with Albecor 1550 and Albecor 1560.

Polyester Resins for Low Temperature Cure for Exterior UseTypically cured with ß-hydroxy alkyl amide

Typically cured with polyglycidyl esters


Albecor 2531 27 – 31 6000 – 8000 65 10 min at 160°C

For applications in combination with Araldite PT 910 (*) or PT 912 (*) in 92:8 ratio. Resulting coatings show full mechanical properties, good flow, no blooming and good outdoor resistance.

* Huntsman

5

60/40 Hybrids



approx. Tg (°C )

Baking Schedule


Albecor 4631 46 – 52 1800 – 2800 53 10 min at 160 °C

High reactivity resin for hybrid coatings. In combination with suitable epoxy resin in 60/40 ratio, it offers good mechanical properties, corrosion resistance and overall chemical resistance. Also with curing cycles from 140° C. Suitable for thin film applications and primers.

Albecor 4611 47 – 54 1600 – 2600 53 10 min at 160 °C

High reactivity resin for hybrid coatings.In combination with suitable epoxy resins in 60/40 ratio, it offers the best balance between reactivity and flow. It is TMA free. Excellent overall performances also with curing cycles from 140° C.

70/30 Hybrids

Albecor 4701 32 – 38 4200 – 5200 57 10 min at 160 °C

High reactivity polyester resin for hybrid coatings.In combination with suit-able epoxy resins in 70/30 ratio, Albecor 4701 offers very good mechanical properties, corrosion resistance and overall chemical resistance also with curing cycles from 140° C.

Polyester Resins for Low Temperature Cure for Interior UseTypically cured with epoxy resins




approx. Tg (°C )

Baking Schedule


Albester 5760 21 – 25 7000 – 8500 64 10 min at 180 °C

15 min at 160°C

Designed for combination with ß-HAA in 96,5:3,5 ratio. The resulting coatings exhibit good flow, exterior durability and mechanical properties along with increased reactivity.

Albester 5501 23 – 27 4500 – 5700 60 15 min at 180 °C

Cures at 96.5/3.5. The final coating shows very good balance between flow and flexibility, good exterior durability and excellent yellowing resistance.

Albester 5671 24 – 29 7000 – 9500 68 10 min at 180 °C

Cures at 96.5/3,5 ratio. Specifically designed for Dye-sublimation technology on textured powder coatings. Excellent sag resistance when high film thickness is requested.

Albester 5651 30 – 35 1800 – 2800 56 10 min at 180 °C

Cures at 95/5. The resulting coatings exhibit an excellent flow and appearance. Suitable for curing with proper Acrylic curative to achieve full matt. Suitable for GSB and Qualicoat approvals.

Albester 5751 32 – 36 2500 – 3500 59 10 minat 180 °C

15 min at 170 °C

Designed for combination with ß-HAA in 95:5 ratio.The resulting coatings exhibit good flow, compatibility and yellowing resistance along with excellent flexibility and improved outdoor resistance. Suitable for GSB and Qualicoat approvals.

Albester 5563 32 – 37 2800 – 3600 61 10 min at 180 °C

Cures at 95/5. Good yellowing resistance, excellent flexibility and ageing. Suitable for GSB and Qualicoat approvals.

Albester 5741 32 – 37 2800 – 3600 61 10 min at 170 °C

Designed for combination with ß-HAA in 95:5 ratio. It has specifically developed to provide good yellowing resistance, excellent flexibility and ageing in applications like PCM and coil coatings. Suitable for GSB and Qualicoat approvals.

Carboxyl-Terminated Polyester Resins for Exterior UseTypically cured with ß-hydroxy alkyl amide

6




approx. Tg (°C )

Baking Schedule


Albester 6150 30 – 35 4500 – 6500 66 10 min at 180 °C

Cures at 95/5. Designed to give a superior exterior durability and consider-ably improved mechanical properties compared to standard superdurable systems. Suitable for GSB Master and Qualicoat Class 2 approvals.

Albester 6181 31 – 37 2700 – 3700 54 10 min at 180 °C

Cures at 95/5. Designed to give a superior exterior durability and improved mechanical properties compared to standard superdurable systems. Suit-able for GSB Master and Qualicoat Class 2 approvals


Albester SilkyMatt 5600

14 – 18 5800 – 6800 51 15 min at 180 °C

Cures at 97.5/2.5. Designed for achieving very low gloss finishing by dry blending with coatings based on Albester SilkyMatt 5680.


18 – 22 5500 – 6300 62 15 min at 180 °C

Cures at 97/3. Designed for low gloss by dry blending with coatings based on Albester SilkyMatt 5590. Excellent quality performances and consistency. Suitable for GSB and Qualicoat approvals.


18 – 22 6000 – 7000 52 15 min at 180 °C

Cures at 97/3. Designed for low gloss by dry blending with coatings based on Albester SilkyMatt 5520. Excellent flexibility.


18 – 22 6700 – 8700 59 15 min at 180 °C

Cures at 97/3. Designed for low gloss by dry blending with coatings based on Albester SilkyMatt 5520. Suitable for GSB and Qualicoat approvals.


18 – 22 6000 – 8000 54 15 min at 180 °C

Cures at 97/3. Specially designed for low gloss in dry blend with Albester SilkyMatt 5770. It gives excellent balance of flexibility and durability. Suitable for GSB and Qualicoat approvals.


32 – 37 3000 – 3800 60 10 min at 180 °C

Cures at 95/5. The resulting coatings, in dry-blend with Albester SilkyMatt 5691 allow very low gloss finishing and are optimized for the Dye-subli-mation. Suitable for GSB and Qualicoat approvals.


46 – 52 3300 – 4300 68 10 min at 180 °C

Cures at 93/7. Designed for low gloss by dry blending with coatings based on Albester SilkyMatt 5540. Excellent quality performances and consistency. Suitable for GSB and Qualicoat approvals.


46 – 52 3500 – 4500 56 10 min at 180 °C

Cures at 93/7. Designed for low gloss by dry blending with coatings based on Albester SilkyMatt 5510. Excellent flexibility.


46 – 52 3000 – 5000 57 10 min at 180 °C

Cures at 93/7. Specially designed for low gloss in dry blend with Albester SilkyMatt 5730. It gives excellent balance of flexibility and durability. Suitable for GSB and Qualicoat approvals.


68 – 78 1800 – 3000 56 10 min at 180 °C

Cures at 90/10, designed for very low gloss in dry-blend with low reactivity resins, especially Albester SilkyMatt 5600.


95 – 105 3500 – 5000 69 10 min at 180 °C

Cures at 87/13. The resulting coatings, in dry-blend with Albester SilkyMatt 5631 allow very low gloss finishing and are optimized for the Dye- subli mation.

Carboxyl-Terminated Polyester Resins for Exterior UseTypically cured with ß-hydroxy alkyl amide

Inside

7

Superdurable – Low gloss



approx. Tg (°C )

Baking Schedule



14 – 18 1800 – 2600 56 15 min at 180 °C

Cures at 97.5/2.5. Provides very low gloss when dry-blended with Albester SilkyMatt 6580. GSB Master and Qualicoat Class 2 approvals.


18 – 22 2000 – 2600 57 15 min at 180 °C

Cures at 97/3. Good flow, high exterior durability. Provides low gloss when dry-blended with Albester SilkyMatt 6580. GSB Master and Qualicoat Class 2 approvals.

AlbesterSilkyMatt 6540

22 – 26 1500 – 2500 56 15 min at 180 °C

Cures at 96.5/3.5. Provides low gloss when dry-blended with Albester Silky-Matt 6580, improved water resistance in comparison with Albester SilkyMatt 6530. Superdurable, suitable for GSB Master and Qualicoat Class 2 approvals.


24 – 28 2400 – 3400 66 15 min at 180 °C

Cures at 96/4. Specifically designed for low gloss in dry blend with Albester SilkyMatt 6590. The system provides improved humidity resistances versus standard versions. Superdurable, suitable for GSB Master and Qualicoat Class 2 approvals.


47 – 55 4000 – 6000 66 10 min at 180°C

Cures at 93/7. Provides low gloss when dry blended with Albester SilkyMatt 6520 or 6530. Superdurable, suitable for GSB Master and Qualicoat Class 2 approvals.


56 – 64 4400 – 5400 69 10 min at 180 °C

Cures at 92/8. Provides low gloss when dry blended with Albester SilkyMatt 6520 or 6530. Superdurable, suitable for GSB Master and Qualicoat Class 2 approvals.


70 – 80 1700 – 3000 69 10 min at 180 °C

Cures at 90/10. Specifically designed for low gloss in dry blend with Albester SilkyMatt 6550. The system provides improved humidity resistances versus standard versions. Superdurable, suitable for GSB Master and Qualicoat Class 2 approvals.

Typically cured with polyglycidyl esters




approx. Tg (°C )

Baking Schedule


Albester 5831 23 – 29 7300 – 8800 63 15 minat 180 °C

Designed for combination with Araldite PT 910 (*) in 93:7 ratio. The result-ing coatings are designed for industrial exterior coatings exhibiting good weathering durability and flow along with excellent flexibility.

Albester 5841 24 – 29 7000 – 9500 68 – Low reactivity carboxyl polyester resin used in 93:7 ratio with Araldite PT910 or Araldite PT912 (*). It is used in combination with other similar resins to adjust reactivity. The resulting coatings exhibit excellent flow and storage stability.

Albester 5851 24 – 29 7000 – 9500 68 10 min at 200 °C

Designed for combination with Araldite PT910 or Araldite PT912 (*) in 93:7 ratio. The resulting coatings exhibit very good mechanical properties, stor-age stability and flow along with good color retention in direct gas-ovens. Suitable for GSB and Qualicoat approvals.

Albester 5871 27 – 31 6000 - 8000 65 10 min at 180°C

Designed for combination with Araldite PT910 or Araldite PT912 (*) in 92:8 ratio. The resulting coatings exhibit very good mechanical properties, storage stability and reactivity along with good colour retention in direct gas-ovens. Suitable for GSB and Qualicoat approvals.


Albester 6800 18 – 24 6500 – 8500 61 15 min at 180 °C

Superior exterior durability in 95:5 ratio with Araldite PT 912 (*). Coatings based on Albester 6800 are suitable for GSB Master and Qualicoat Class 2 approvals.

Inside

8

Carboxyl-Terminated Polyester Resins for Exterior UseTypically cured with TGIC (Triglycidyl Isocyanurates)




approx. Tg (°C )

Baking Schedule


Albester 5250 25 – 30 5000 – 6300 62 10 min at 200 °C

Designed for combination with TGIC in 95:5 ratio. The resulting coatings are designed for industrial exterior finishing.

Albester 5140 30 – 36 3500 – 4500 68 10 min at 200 °C

Low reactivity resin showing excellent storage stability together with an excellent flow. Exterior durable for architectural applications, Qualicoat and GSB approvable, suitable for TGIC at 93/7 ratio.

Albester 5342 30 – 36 3800 – 5400 68 10 min at 200°C

Low reactivity resin designed for combination with TGIC in 93:7 ratio. The resulting coatings exhibit excellent flexibility, storage stability and outstanding flow. It is suitable for GSB, Qualicoat and AAMA approvals.

Albester 5070 32 – 37 2800 – 3800 61 15 min at 150 °C

Designed for curing with TGIC in 93:7 ratio for high speed lines. The resulting coatings exhibit, excellent flexibility and exterior durability. Designed to be used with texturing agent for wrinkle effect. It starts curing from 130 °C

Albester 5160 32 – 37 2800 – 3800 61 10 min at 180°C

Designed for combination with TGIC in 93:7 ratio. The resulting coatings exhibit excellent flow, good flexibility and exterior durability.

Albester 5050 32 – 38 3000 – 3800 61 10 min at 180°C

Designed for combination with TGIC in 93:7 ratio or with ß-HAA in 95:5 ratio. The resulting coatings exhibit excellent reactivity. Suitable for curing with proper Acrylic curative to achieve full matt.

Albester 5198 32 – 38 3500 – 5000 64 10 min at 200°C

Medium-high reactivity resin, designed for combination with TGIC in 93:7 ratio. The resulting coatings exhibit excellent flexibility, storage stability and outstanding flow along with excellent boiling water resistance. Suitable for GSB and Qualicoat approvals.


Albester 6140 30 – 35 4000 – 6000 65 10 min at 200 °C

Designed to give a superior exterior durability in 93:7 ratio with TGIC.Suitable for GSB and Qualicoat Class 2 approvals.



18 – 22 5000 – 6200 60 10 min at 200 °C

Cures at 96/4 with TGIC, excellent for matt coatings when dry-blended with Albester SilkyMatt 5901. Suitable for GSB and Qualicoat approvals

Albester 5220 27 – 32 5500 – 7500 62 15 min at 180°C

Suitable for combination with TGIC in 94:6 or 95:5 ratios for industrial coa-tings. Specifically designed for one shot matt finishing with proper matting agent and curing cycle at 200°C for 10 min. Excellent storage stability.


46 – 52 3000 – 4000 67 10 min at 200 °C

Cures at 90:10 ratio with TGIC. Designed for low gloss dry-blend in com-bination with Albester SilkyMatt 5401. Suitable for GSB and Qualicoat approvals. Suitable for dye-sublimation with excellent film and paper detachment.

9

Hydroxyl-Terminated Polyester Resins for Exterior UseTypically cured with isocyanates


Product OH Value (mg KOH/g)

Acid Value (mg KOH/g)


approx. Tg (°C )

Baking Schedule*


Albester 3840 20 – 30 5 – 10 7500 – 9000 56 10 min at 200 °C

Resin designed to be cured with low ratios of Uretdione curing agents. Formulation cost reduction still keeping excellent flexibility along with good gloss and weathering resistance.

Albester 3270 33 – 43 6 – 12 8000 -11000 67 15 min at 200 °C

Designed to be cured with low ratios of uretdione curing agents. It is characterized by high Tg and superior viscosity during the extrusion process. It allows to formulate powder coatings with special surface effects.

Albester 3120 45 – 55 8 max 4800 – 6000 56 10 min at 200 °C

Designed primarily to be cured with aliphatic isocyanates but also with Uretdione technology. Superior flow, excellent exterior durability, flexibility, gloss and pigment wetting. Also suitable for clear coating.


Cured in combination with non-emitting isocyanates, offers excellent solvent, detergent and stain resistance with good mechanical properties.


It has been specifically developed for Antigraffiti coatings cured with non-emitting Isocyanates.The resin, having a high cross-link density, gives a very hard film with superior solvent and stain resistance.


Specifically developed for antigraffiti coatings cured with non-emitting isocyanate. With high cross-linking density, it gives very hard film with superior solvent and stain resistance. Enhanced outdoor durability in comparison with Albester 3401.


It has been specifically developed for antigraffiti paint cured with non-emitting isocyanate. Having a high cross-link density, gives a very hard film with superior solvent and stain resistance.



Used in combination with non-emitting isocyanate curatives, offers excellent stain, detergent/chemical resistance. The res-in has been specifically designed to give a superior exterior durability in the range of “superdurable” resins. Suitable for GSB Master and Qualicoat Class 2 approvals.



43 – 53 4 max 4300 – 5300 57 10 min at 200 °C

Low gloss in one shot with Albester SilkyMatt 3115 and non-emitting isocyanate curative. The resulting coating system offers good flexibility, impact resistance and exterior durability. Specifically designed for Dye Sublimation effect.

AlbesterSilkyMatt 3600

43 – 53 4 max 6500 – 8000 63 10 min at 200 °C

Low gloss in one shot with Albester SilkyMatt 3115 and non-emitting isocyanate curative. The resulting coating system offers good flexibility, impact resistance and exterior durability. Specifically designed for Dye Sublimation effect with high storage stability.


280 – 310 7 – 11 2100 – 3000 50 10 min at 200 °C

Hydroxyl functional, highly branched resin. Combines in one shot with Albester SilkyMatt 3225 or Albester SilkyMatt 3600 for low gloss finishes. These systems are recommended in dye-sublimation and automotive applications. When used by itself, the resin provides an excellent antigrafitti and solvent resistance.

* Baking schedule of hydroxyl-terminated polyesters is related to Uretdione technology.

10

Hydroxyl-Terminated Polyester Resins for Exterior UseTypically cured with isocyanates

Superdurable – Low gloss

Product app. OH Value (mg KOH/g)



approx. Tg (°C )

Baking Schedule*



38 – 48 4 max 6500 – 8000 56 10 min at 200 °C

Superdurable resin to be blended in one shot with Albester SilkyMatt 6615 to produce low gloss finishing suitable for dye-sublimation, outstanding weathering and Florida resis-tance compared to Albester SilkyMatt 6320. Suitable for GSB Master and Qualicoat Class 2 approvals.


39 – 49 4 max 3600 – 4800 55 10 min at 200 °C

Low gloss in one shot with Albester SilkyMatt 3115 and non-emitting isocyanate curative. The resulting coating system offers good flexibility, impact resistance and exterior durability. Specifically designed for Dye Sublimation effect with improved outdoor performances. GSB and Qualicoat approvable.


270 – 300 6 max 2400 – 3400 53 10 min at 200 °C

Superdurable resin to be blended in one shot with Albester SilkyMatt 6620 to produce low gloss finishing suitable for dye-sublimation, outstanding weathering and Florida resistance. Suitable for GSB Master and Qualicoat Class 2 approvals.

* Baking schedule of hydroxyl-terminated polyesters is related to Uretdione technology.

Carboxyl-Terminated Polyester Resins for Interior UseTypically cured with epoxy resins

50/50 Hybrids



approx. Tg (°C )

Baking Schedule


Albester 2871 65 – 75 1000 – 2500 50 15 min at 160°C

High reactivity polyester resin for hybrid coatings. It offers an improved flow, good mechanical properties, corrosion and overall chemical resis-tance.

Albester 2381 68 – 78 1800 – 3000 56 15 min at 160 °C

High reactivity resin for hybrid coatings. In combination with suitable epoxy resin in 50/50 ratio, it is the typical resin for Domestic Appliance when excellent chemical properties are required.

Albester 2385 68 – 78 1600 – 3200 57 15 min at 160°C

High reactivity polyester resin for 50/50 hybrids. It offers good flow, good chemical and mechanical properties.

60/40 Hybrids

Albester 2101 47 – 53 2000 – 2800 53 15 min at 200 °C

Low reactivity resin for 60/40 hybrid coatings. In combination with suitable epoxy resins, it offers outstanding flow and is suitable as Primer on metal substrates. It can be applied in the transportation field.

Albester 2230 47 – 53 1800 – 2600 53 10 min at 180 °C

High reactivity resin for hybrid coatings in combination with suitable epoxy resins in 60/40 ratio. It is the perfect resin for thin film applications and high quality for Domestic Appliance coatings.

Albester 2235 47 – 53 1500 – 3000 53 10 minutes at 180°C

High reactivity polyester resin for hybrid coatings in combination with suitable epoxy resins in 60/40 ratios.

Albester 2466 48 – 54 3500 – 4500 52 10 min at 180 °C

High reactivity resin for hybrid coatings. In combination with suitable epoxy resins in 60/40 ratio, it offers good flow along with excellent flexibility, corrosion resistance and overall chemical resistance. TMA free resin.

Albester 2850 48 – 55 2000 – 4000 62 10 minutes at 180°C

High reactivity polyester resin for hybrid coatings in 60/40 ratio. It combines all the advantages given by a high Tg along with an excellent flow.

11

Carboxyl-Terminated Polyester Resins for Interior UseTypically cured with epoxy resins

70/30 Hybrids



approx. Tg (°C )

Baking Schedule


Albester 2640 32 – 38 4500 – 6500 60 10 min at 180 °C

High reactivity resin. In combination with suitable epoxy resins in 70/30 ratio, it provides hybrid decorative coatings with good mechanical and flow properties, along with improved storage stability.

Albester 2660 32 – 38 3800 – 5200 54 10 min at 180 °C

High reactivity resin. In combination with suitable epoxy resins in 70/30 ratio, it provides hybrid decorative coatings with good mechanical and flow properties.

Albester 2670 32 – 38 3800 – 5200 54 15 min at 180 °C

Medium reactivity resin. In combination with suitable epoxy resins in 70/30 ratio, it provides hybrid decorative coatings with good mechanical and enhanced flow properties.

Albester 2681 32 – 38 3600 – 5000 54 10 min at 180 °C

High reactivity resin. In combination with suitable epoxy resins in 70/30 ratio, Albester 2681 provides hybrid decorative coatings with good mechanical and flow properties along with good color retention in gas oven.

Albester 2600 33 – 38 4100 – 5100 54 10 min at 200 °C

Low reactivity resin. In combination with suitable epoxy resins in 70/30 ratio, Albester 2600 provides hybrid decorative coatings with good mechanical properties along with excellent flow.

AdditivesAdditives

Additives

Product app. OH Value (mg KOH/g)



approx. Tg (°C )


Albemast 9100 45 – 55 8 max 2500 – 4000 51 Tribo additive masterbatch suitable to adjust the tribo chargeability of all standard polyester resins. Albemast 9100 is a hydroxyl terminated polyester containing 5% of active matter.

Albemast 9200 – 30 – 38 1700 – 2700 62 Tribo additive masterbatch 5% content based on carboxyl terminated resins, suitable to adjust the tribo chargeability of any type of carboxyl powder coating.

Albemast 9420 50 8 2000 – 4500 54 Flow promoter 15% additive masterbatch on Hydroxyl terminated resins, suitable to adjust the flow of any powder coating formulation.

Albemast 9600 – 14 – 18 1800 – 2600 56 Designed for gloss control in low gloss poly-urethane one shot powder coatings formulations based on Albester SilkyMatt resins. Small additions on binder raise the gloss of coated film to the desired level. Dye sublima-tion proved.

www.synthomer.com

Leading in emulsions and speciality polymers

Synthomer is one of the world’s leading suppliers of emulsion and speciality polymers supporting leadership positions in many market segments including coatings, construction, technical textiles,adhesives, paper and synthetic latex gloves. The company has its Head Office in London (UK) and provides customer focused services from operational centres in Harlow (UK), Marl (Germany),Kuala Lumpur (Malaysia), Shanghai (China) and Dubai (UAE). In June 2016 we have acquired the Monomers, Dispersions and

Powders business (MDP) from Hexion with dedicated production,sales and customer service facilities in North America, Europe and South East Asia. The newly acquired business significantly improves our footprint to a number of speciality markets which we will continue to serve through a strong network of local technical service and sales branches, supported by regional application development and production in our key markets. We deliver the right formula, globally, individually.

Disclaimer: This information and any other advice or recommendations given or made by us (collectively “Information”), are provided in good faith and are not intended to, nor do they, constitute professional

advice or services. Information is provided “AS IS” and on an “AS AVAILABLE” basis and without warranty. We do not warrant or accept responsibility for the accuracy, timeliness or completeness of

the Information, or for the suitability of the Information for a particular purpose. We do not accept responsibility, and exclude all liability (including under any implied warranties), for any matters arising

out of or in connection with your reliance on the Information (including as to infringement of third party intellectual property rights) to the fullest extent permitted by law. Any Information concerning any

possible use or application of Synthomer products is given by us in good faith; we do not warrant the fitness of any Synthomer products for any particular purpose and it is entirely for you to satisfy your-

self fully as to the suitability of Synthomer products for any particular purpose. Synthomer products are sold in accordance with Synthomer’s standard terms and conditions of sale which are available from

www.synthomer.com/tc.

Synthomer plc45 Pall MallLondon SW1Y 5JGUnited Kingdom

[email protected]

Group Head Office

Synthomer Specialty Resins S.r.l.Via Morozzo 2712040 Sant’Albano Stura Italy

Phone +39 0172 [email protected]

Business Unit Powder Coatings

Documents

Powder Coating Resins and Additives - Home- SYNTHOMER · 3 Powder Coatings Easy to use, minimal VOC and cost effective, powder coating has emerged in recent decades as a most desirable