56
INSTALLATION & OPERATING INSTRUCTIONS Gas-Fired Pool & Spa Heater Catalog No. 6000.59S Effective: 04-01-10 Replaces: 04-03-09 P/N 241236 Rev. 20 WARNING: If these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or death. WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor's phone. Follow the gas sup- plier's instructions. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future reference. Atmospheric Models 206A, 266A, 336A & 406A Low NOx Models 207A, 267A, 337A & 407A Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Pool Heater

Embed Size (px)

Citation preview

Page 1: Pool Heater

INSTALLATION & OPERATINGINSTRUCTIONS

Gas-FiredPool & SpaHeater

Catalog No. 6000.59S Effective: 04-01-10 Replaces: 04-03-09 P/N 241236 Rev. 20

WARNING: If these instructions are not followed exactly, a fire or explosion may resultcausing property damage, personal injury or death.

WHAT TO DO IF YOU SMELL GAS:• Do not try to light any appliance.• Do not touch any electrical switch; do not use any phone in your building.• Immediately call your gas supplier from a neighbor's phone. Follow the gas sup-

plier's instructions.• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency orthe gas supplier.

This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for futurereference.

Atmospheric Models206A, 266A, 336A & 406A

Low NOx Models207A, 267A, 337A & 407A

Do not store or use gasoline or other flammable vapors and liquids in the vicinity ofthis or any other appliance.

Page 2: Pool Heater

WATER CHEMISTRY(Corrosive water voids all warranties)

For your health and the protection of your pool equipment, it is essential that yourwater be chemically balanced. The following levels must be used as a guide for bal-anced water.

Recommended Level(s) Fiberglass Pools Fiberglass Spas Other Pool & SpaTypes

Water Temp. (Deg. F) 68 to 88 89 to 104 68 to 104

pH 7.3 to 7.4 7.3 to 7.4 7.6 to 7.8

Total Alkalinity (PPM) 120 to 150 120 to 150 80 to 120

Calcium Hardness (PPM) 200 to 300 150 to 200 200 to 400

Salt (PPM) 6000 MAXIMUM 6000 MAXIMUM 6000 MAXIMUM

Free Chlorine (PPM)* 2 to 3 2 to 3 2 to 3

Total Dissolved Solids (PPM) 3000 MAXIMUM 3000 MAXIMUM 3000 MAXIMUM

* Free Chlorine MUST NOT EXCEED 5 PPM!

• Occasional chemical shock dosing of the pool or spa water should not damage theheater providing the water is balanced.

• Automatic chemical dosing devices and salt chlorinators are usually more efficientin heated water, unless controlled, they can lead to excessive chlorine level whichcan damage your heater, and which is not covered under warranty.

• Further advice should be obtained from your pool or spa builder, accredited poolshop, or chemical supplier for the correct levels for your water.

2

Rev. 20 reflects the following:Changes to: Water chemistry notes on page 2, text on pager 8, text on page 18, wiring diagrams on pages 29 and 30Additions: Note on page 26, “Time Clock/Firemanʼs Switch” section on page 38

Page 3: Pool Heater

4 PART ONEOWNER'S OPERATING INSTRUCTIONS

4 SECTION 1START-UP PROCEDURES

4 Before Start-Up5 Lighting Instructions & Shut-Off Procedures -

Manually Lighted Pilots MV6 Operating Instruction & Shut-Off Procedures -

Automatically Lighted Pilots IID7 After Start-Up7 SECTION 2

CAUTION8 SECTION 3

MAINTENANCE & CARE PROCEDURES8 Pool & Spa Water Chemistry8 Automatic Chlorinators & Chemical Feeders9 Cold Weather Operation9 Winterizing the Pool & Spa Heater10 PART TWO

INSTALLATION & SERVICE INSTRUCTIONS10 SECTION 1

RECEIVING EQUIPMENT11 SECTION 2

GENERAL SPECIFICATIONS11 SECTION 3

INSTALLATION INSTRUCTIONS11 Code Requirements12 Clearances12 Outdoor Heater Installation14 Florida Building Code 200115 Indoor Heater Installation15 Outdoor Stack/Indoor Stack16 Atmospheric Specifications and Dimensions17 Low NOx Specifications and Dimensions18 Combustion and Ventilation Air18 Vent Piping19 Gas Supply Connections20 Gas Pressure Regulator20 Gas Pressure Adjustment Locations20 Pipe Sizing For Gas Connections21 Flow Rates21 Heat Exchanger Pressure Drop Tables22 Polymer Headers22 Cast Iron Headers22 Unitherm Governor Operation23 Internal Automatic Bypass Valve23 External Auxiliary Bypass Valve23 Auxiliary Bypass Valve Adjustment23 Pressure Relief Valve Installation24 Plumbing—Water Connections25 Heat Exchanger Reversal Procedure26 Electrical Wiring26 Millivolt Models26 Digital Models27 Transformer Wiring28 Wiring Diagram - Millivolt (Mechanical Therm.)29 Wiring Diagram - Digital Models, Atmospheric

30 Wiring Diagram - Digital Models, Low NOx31 SECTION 4

SERVICING INSTRUCTIONS31 General Location of Controls32 Control Panel Removal32 Control Adjustments - Digital Models32 Control Adjustments - Millivolt Models33 Digital Thermostat Controls33 Thermostat Control Operation35 Diagnostics35 Codes35 Reading a Fault36 Remote Control Installation and Operation36 Remote Operation36 Activating the Remote37 Remote Control Wiring37 2-Wire Remote Control37 3-Wire Remote Control38 Time Clock / Firemanʼs Switch38 Water Pressure Switch38 Flame Roll-Out Safety Switch38 High Limits39 Pilot Safety39 Burner Tray Removal (ATM)39 Gas Valve Removal (ATM)39 Main Burner and Orifice Removal (ATM)39 Pilot Removal and Cleaning40 Heat Exchanger Removal40 Tube Cleaning Procedure40 Desooting Procedure40 Combustion Chamber Removal40 Immersion Well Replacement41 Unitherm Governor (U.G.) Replacement41 Low NOx Pool Heaters41 Operation41 Start-Up Procedures41 Visual Inspection41 Electrical41 Flame Roll-Out Safety Switch42 Burner Tray Removal42 Gas Valve Removal42 Main Burner and Orifice Removal42 Pilot Removal42 Combustion Blower Removal43 SECTION 5

TROUBLESHOOTING44 Electrical - Standing Pilot Millivolt45 Electrical - Electronic Ignition (IID)46 Digital Control Logic - Flow Chart47 SECTION 6

REPLACEMENT PARTS48 Illustrated Parts List51 Part Numbers

3

CONTENTS

Page 4: Pool Heater

4

PART ONEOWNER'S OPERATING INSTRUCTIONSFOR YOUR SAFETY - READ BEFORE OPERATINGWARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAYRESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

SECTION 1 - START-UP PROCEDURES

Your pool/spa heater has been designed for years of safe and reliable pool/spa water heating. It is available withmillivolt or electronic ignition. ASME-certified units, typically used in commercial applications, are also available.This manual provides installation, operation, maintenance, and service information for these heaters.

If your heater has been installed correctly, operating the heater is an easy task. The upper front panel of theheater contains the control center that allows you to turn the heater On or Off and adjust the temperature set-tings for the pool or spa. The temperature range is factory set from 65°F (18°C) to 104°F (40°C). See figureabove for location of toggle switch to turn the heater On and Off. Section 4 of this manual contains more detailsabout the use of the controls in the Control Adjustments subsection (page 31).

ON

OFF

BEFORE START-UP

BURNERSClean main burners, combustion fan (if equipped)and air louvers of dust, lint and debris. Keepheater area clear and free from combustibles, flamma-ble liquids and chemicals. Do not obstruct the flow ofcombustion and ventilation air.

WATERWater must be flowing through the heater during oper-ation. Ensure that system is filled with water and havepump operating.

Page 5: Pool Heater

5

CAUTION: Propane gas is heavier than air and will settle on the ground. Since propane can accumulate inconfined areas, extra care should be exercised when lighting propane heaters.

LIGHTING INSTRUCTIONS AND SHUT-OFF PROCEDURESMILLIVOLT SYSTEM

(MANUALLY LIGHTED PILOT)

A. This appliance has a pilot that must be lit byhand. When lighting the pilot, follow theseinstructions exactly.

B. BEFORE LIGHTING, smell all around theappliance area for gas. Be sure to smell nearthe floor because some gas is heavier than airand will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:*Do not try to light any appliance.*Do not touch any electric switch; do not useany phone in your building.

*Immediately call your gas supplier from aneighbor's phone. Follow the gas supplier'sinstructions.

*If you cannot reach your gas supplier, call thefire department.

C. Use only your hand to push in or turn the gascontrol knob. Never use tools. If the knob willnot push in or turn by hand, do not try to repairit. Call a qualified service technician. Force orattempted repair may result in a fire or explo-sion.

D. Do not use this appliance if any part has beenunder water. Immediately call a qualified serv-ice technician to inspect the appliance and toreplace any part of the control system and anygas control which has been under water.

1. STOP! Read the safety information above.2. Set the thermostat on the lowest setting.3. Turn On/Off switch to the "Off" position.4. Remove heater door panel.5. Push in gas control knob slightly and turn

clockwise to "Off".NOTE: Knob cannot be turned from "Pilot" to Off"

unless knob is pushed in slightly. Do notforce.

6. Wait 5 minutes to clear out any gas. If youthen smell gas, STOP! Follow "B" in thesafety information above. If you don't smellgas, go to the next step.

7. Locate pilot mounted on the right side panel ofthe burner tray.

LIGHTING INSTRUCTIONS

8. Turn gas control knob counter-clockwiseto "Pilot"

9. Place flame to end of pilot tube. Push incontrol knob all the way and hold to light pilot.Continue to hold control knob in for about oneminute after the pilot is lighted, release knoband it will pop back up. Pilot should remainlighted. If it goes out, repeat steps 5 through 9.If knob does not pop up when released, stopand immediately call your service technician orgas supplier.

10. Stand to the side of the heater and turn thegas control knob counter-clockwise

to "On".11. Replace heater door panel.12. Turn On/Off switch to the "On" position.13. Set thermostat to the desired setting.

1. Set the thermostat to the lowest setting.2. Turn On/Off switch to the "Off" position.3. Remove heater door panel.

4. Push the gas control knob slightly and turnclockwise to "Off". Do not force.

5. Replace heater door panel.

SHUT-OFF PROCEDURE

HONEYWELLMILLIVOLTGAS VALVE

INVENSYS/ROBERTSHAWMILLIVOLTGAS VALVE

HONEYWELL PILOT ROBERTSHAW PILOT

Page 6: Pool Heater

6

CAUTION: Propane gas is heavier than air and will settle on the ground. Since propane can accumulate inconfined areas, extra care should be exercised when lighting propane heaters.

OPERATING INSTRUCTIONS AND SHUT-OFF PROCEDURESELECTRONIC IGNITION SYSTEM

(AUTOMATICALLY LIGHTED PILOT)A. This appliance is equipped with an ignition

device which automatically lights the pilot. Donot try to light the pilot by hand.

B. BEFORE OPERATING, smell all around theappliance area for gas. Be sure to smell nearthe floor because some gas is heavier than airand will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:*Do not try to light any appliance.*Do not touch any electric switch; do not useany phone in your building.

*Immediately call your gas supplier from aneighbor's phone. Follow the gas supplier'sinstructions.

*If you cannot reach your gas supplier, call thefire department.

C. Use only your hand to push in or turn the gascontrol knob. Never use tools. If the knob willnot push in or turn by hand, do not try to repairit. Call a qualified service technician. Force orattempted repair may result in a fire orexplosion.

D. Do not use this appliance if any part has beenunder water. Immediately call a qualifiedservice technician to inspect the appliance andto replace any part of the control system andany gas control which has been under water.

1. STOP! Read the safety information above.2. Set the thermostat to the lowest setting.3. Turn off all electrical power to the appliance.4. This appliance is equipped with an ignition

device which automatically lights the pilot. Donot try to light the pilot by hand.

5. Remove heater door panel.6. For Honeywell valve: Turn gas control knob

clockwise to "Off".For Robertshaw valve: Models 266-406:Turn gas control knob clockwise to"Off". Model 206: Push in and move gas con-trol lever counter-clockwise to "Off"position.

7. Wait 5 minutes to clear out any gas. If youthen smell gas, STOP! Follow "B" in the safe-ty information above. If you don't smell gas, goto the next step.

8. Turn gas control knob counter-clockwiseto "On". (Honeywell VR 8300 and

Robertshaw 7000)9. Replace heater door panel.10. Turn on all electrical power to the appliance.11. Set thermostat to desired setting.12. If the appliance will not operate, follow the

instructions "To Turn Off Gas To Appliance"and call your service technician or gassupplier.

OPERATING INSTRUCTIONS

1. Set the thermostat at the lowest setting.2. Turn off all the electrical power to the appli-

ance if service is to be performed.3. Remove heater door panel.4. For Honeywell VR 8300 and Robertshaw

7000 gas valve.Turn gas control knob clockwise

to "Off". Make sure knob rest against stop.For Robertshaw 7200 gas valve.Push in and move gas control lever counter-clockwise to "Off" position.

5. Replace heater door panel.

SHUT-OFF PROCEDURES

OOF

ROBERTSHAW 7000GAS VALVE IID

HONEYWELLVR 8300 GASVALVE IID

GASINLET

GASINLET

ROBERTSHAW 7200GAS CONTROLLEVER SHOWNIN “OFF”POSITION

Page 7: Pool Heater

7

AFTER START-UP

Feel the inlet and outlet pipes. Outlet pipe should beonly slightly warmer than the inlet. It should not be hot.

VISUAL INSPECTION - ATMOSPHERIC HEATERSWith the heater on, remove the door and make a visu-al check of the pilot and burner. The flame should beblue with a well-defined pattern.

4" MAX

MAIN BURNER FLAME

MILLIVOLT PILOT BURNER FLAME

A yellow or "floating" flame indicates restricted airopenings or incorrect orifice size. Should this occur,shut the heater off and contact your installer or gassupplier.

WATER PRESSURE SWITCHA water pressure switch is provided in the heater toshut off the burners in the event that water supply isinterrupted. It is very important to verify that the switchelectrically opens and shuts off the gas valve whenwater flow to the heater is interrupted. Otherwise,rapid and severe damage will likely occur to theheater. (The water pressure switch should be checkedand adjusted for proper operation by a qualified serv-ice person at the time of installation and periodicallychecked thereafter. Refer to Pressure SwitchAdjustment on pg. 38 of this manual).

WARNING: Should overheating occur or the gassupply fail to shut off, turn off the manual gas controlto the appliance.

SECTION 2 - CAUTIONElevated water temperature can be hazardous. TheU.S. Consumer Product Safety Commission has theseguidelines:

1. Spa water temperatures should never exceed104°F (40°C). A temperature of 100°F (38°C) isconsidered safe for a healthy adult. Special cautionis suggested for young children.

2. Drinking of alcoholic beverages before or duringspa or hot tub use can cause drowsiness whichcould lead to unconsciousness and subsequentlyresult in drowning.

3. Pregnant Women Beware! Soaking in water over102°F (39°C) can cause fetal damage during thefirst three months of pregnancy resulting in the birthof a brain-damaged or deformed child. Pregnantwomen should stick to the 100°F (38°C) maximumrule.

4. Before entering the spa or hot tub, users shouldcheck the water temperature with an accurate ther-mometer; spa or hot tub thermostats may err in reg-ulating water temperatures by as much as 4°F(2.2°C).

5. Persons with a medical history of heart disease, cir-culatory problems, diabetes, or blood pressureproblems should obtain a physician's advice beforeusing pools or hot tubs.

6. Persons taking medications which induce drowsi-ness, such as tranquilizers, antihistamines, or anti-coagulants, should not use spas or hot tubs.

WARNING: Operation of the heater without watercirculation will cause rapid and severe damage tothe heater.

Page 8: Pool Heater

SECTION 3 - MAINTENANCE ANDCARE PROCEDURES

To be followed one month after start-up and then semi-annually.

1. Inspect top of heater and drafthood for soot, asticky black substance around finned tubes and"V" baffles, and open flue gas passageways. Anyvisible soot should be cleaned for proper opera-tion.

2. Clean main burners and pilot burner of dust andlint.

3. Inspect and operate all controls, gas valve andpressure relief valve (if equipped).

4. Make visual check of the burner and pilot flames.Flame pattern on the main burner and pilot is illus-trated on page 7. Yellow flame means restrictionof the air openings. Lifting or blowing flame indi-cates high gas pressure. Low flame means lowgas pressure. Should the latter occur, shut theheater off and contact your gas supplier or quali-fied service agency.

5. On indoor heaters, clean room intake openings toensure adequate flow of combustion and ventila-tion air.

6. Keep area around heater clear and free from com-bustible materials, gasoline and other flammableand corrosive vapors and liquids.

IF HEATER WILL NOT FIRE:

If you have no electrical power, it may be that your"circuit breaker" has tripped. Try re-setting it.

If you have electrical power but the heater will not firecheck the following or see Troubleshooting section:

1. The time clock must be in the "ON" position.

8

CAUTION: Soot may be combustible. Wet sootedsurfaces completely prior to cleaning. Do not usesteel wire brush.

3. Your filter may be dirty. If so, backwash or cleanfilter. (To tell if your filter is dirty, look to see if thefilter pressure will be higher than usual).

4. The pump may have lost its prime and be runningdry. Check the pressure on the filter. If there is nopressure; then you are not moving water (or yourgauge is broken). Try to get the pump to run at itsnormal flow rate.

CAUTION: Combustion air must not be contaminat-ed by corrosive chemical fumes which can damagethe heater and void the warranty.

WARNING: Check the heater for possible rodentnests after long periods of non-use.

2. Your pump strainer basket may be full. If soremove debris.

POOL & SPA WATER CHEMISTRY

Chemical imbalance can cause severe damage toyour heater and associated equipment. Maintainyour water chemistry according to the chart on page 2.If the mineral content and dissolved solids in the waterbecome too high, scale forms inside the heat exchang-er tubes, reducing heater efficiency and damaging theheater. If the pH drops below 7.2, this will cause cor-rosion of the heat exchanger and severely damage theheater. Heat exchanger damage resulting fromchemical imbalance is not covered by the warran-ty.

AUTOMATIC CHLORINATORS ANDCHEMICAL FEEDERS

All chemicals must be introduced and completely dilut-ed into the pool or spa water before being circulatedthrough the heater. Do not place sanitizing chemicalsin the skimmer. High chemical concentrations willresult when the pump is not running (e.g. overnight).

Chlorinators must feed downstream of the heater andhave an anti-siphoning device to prevent chemicalback-up into the heater when the pump is shut off.

See plumbing diagrams on page 24.

NOTE: High chemical concentrates from feeders andchlorinators that are out of adjustment will cause rapidcorrosion to the heat exchanger. Such damage is notcovered under the warranty.

The Low NOx burners and orifice areas should beinspected annually. Dirt and debris can affect theoperation of the heater and could damage the burnersor prevent the heater from firing. DO NOT clean theburners with a wire brush.

Page 9: Pool Heater

9

COLD WEATHER OPERATION

IMPORTANT FREEZE INFORMATIONMODERATE CLIMATE: Heater operation can contin-ue during short-term cold spells. When temperaturesare between 0° and 32°F, flow (continuous pumpoperation) must be maintained.

CAUTION: Do not use the heater to maintain watertemperatures just above freezing or for freeze protec-tion. When heater is used during freezing weather,care must be taken to avoid freeze-ups. Continuouspump operation is a must. Additional protection maybe required. The heater is not warranted againstfreeze-ups.

COLD CLIMATE: Prolonged operation with watertemperatures below 50°F is not recommended.When starting the heater with water temperaturesbelow 50°F, operate the heater continuously untilhigher temperatures are reached. Operating theheater for prolonged periods with pool water below50°F can seriously damage the heater, and is not cov-ered by the warranty.

For cold climate areas, please follow the winterizingprocedures listed.

WINTERIZING THE POOL & SPA HEATER

Heaters installed outdoors in freezing climate areasmay be shut down for the winter. Observe the follow-ing procedure for winterizing the heater:

1. Turn off gas valve, manual gas valve, and electri-cal supply to the heater.

2. Open drain plug located on the inlet/outlet header,(under water pipes). Remove the heat exchangerinspection panel on the side opposite water pipingto gain access to the drain plug on the return head-er. Open drain plug on return header.

3. For ASME Heaters only: Disconnect compressionfittings from the pressure switch and return headerthat connects to the 1/4" copper tube and allow thetube to drain.

Return Header

Drain Plug

Page 10: Pool Heater

10

PART TWOINSTALLATION AND SERVICE INSTRUCTIONSSECTION 1 - RECEIVING EQUIPMENT

The manufacturer recommends that this manual be reviewed thoroughly before installing your pool/spa heater.If there are any questions that this manual does not answer, please contact the factory or your local represen-tative.On receipt of your equipment it is suggested that you visually check for external damage to the carton. If thecarton is damaged, a note should be made on the Bill of Lading when signing for the equipment. Remove theheater from the carton. If it is damaged, report the damage to the carrier immediately. Save the carton.

These items are shipped inside a box in the carton with the heater:

STANDARD UNIT (POLYMER HEADERS) ASME UNIT (CAST IRON HEADERS)1. "Pagoda" top 1. "Pagoda" top2. 2" CPVC union with "O" rings (2) 2. In/Out flanges (2)3. Plastic pipe finish flange for gas line 3. 1-1/2" flange gaskets (2)4. Bonding lug with mounting screw 4. 2" flange gaskets (2)

(Digital models only) 5. Flange bolts (4)6. Pressure relief valve7. 2" CPVC adapters (2)8. Plastic pipe finish flange for gas line.9. Bonding lug with mounting screw.

(Digital models only)

Be sure that you receive the number of packages indicated on the Bill of Lading.

When ordering parts, you must specify the model and serial numbers of the heater. See below for location ofserial number. When ordering under warranty conditions, you must also specify date of installation.

Serial No.LABEL ON CARTON

Model & Serial No.Located on RatingPlate

(Alternate Location)

The Model & Serial No.can also be found insidethe bezel above the display

Page 11: Pool Heater

11

SECTION 3 - INSTALLATION INSTRUCTIONSCALIFORNIA PROPOSITION 65 WARNING: This product contains chemicals known to the State of Californiato cause cancer, birth defects or other reproductive harm.

IMPORTANT NOTICEThese instructions are intended only for the use of qualified personnel, specifically trained and experienced inthe installation of this type of heating equipment and related system components. Installation and service per-sonnel may be required by some states to be licensed. If your state is such, be sure your contractor bears theappropriate license. Persons not qualified shall not attempt to fix this equipment nor attempt repairs accordingto these instructions.

WARNING: Improper installation, adjustment, alteration, service or maintenance may damage the equip-ment, create a hazard resulting in asphyxiation, explosion or fire, and will void the warranty.

CODE REQUIREMENTSNOTE: The heater should not be located in an area where possible water leakage will result in damage to thearea adjacent to the heater or to the structure. When such locations cannot be avoided, it is recommended thata suitable drain pan, with adequate drainage, be installed under the heater. The pan must not restrict combus-tion air flow.

Installation must be in accordance with local codes, or, in the absence of local codes, with the latest edition ofthe National Fuel Gas Code, ANSI Z223.1/NFPA54 and National Electrical Code, ANSI/NFPA 70, and forCanada, the latest edition of CAN/CGA-B149 Installation Codes, and Canadian Electrical Code, CSA C22.1 Part1 and Part 2.

SECTION 2 - GENERAL SPECIFICATIONSThese heaters are design-certified and tested under the latest requirements of the ANSI Z21.56 / CSA 4.7Standard for Gas-Fired Pool Heaters. All heaters can be used either indoor or outdoors. The appropriate topdesignated for each type of use is required. If necessary, the top can be changed at a later date to change fromoutdoor to indoor or vice versa. Millivolt heaters contain a self-generating electrical system operating between.25 and .75 VAC.

Ambient Temperature Rating of Heater ComponentsMillivolt Heater with Honeywell Gas Valve +32°F to +175°FMillivolt Heater with Robertshaw Gas Valve 0°F to +175°FDigital Heater* -32°F to + 175°F*Requires 120 or 240VAC Power Supply

Atmospheric heaters:Rated inputs are suitable for up to 2,000 feet elevation. For elevations above 2000 feet, reduce input 4% foreach 1,000 feet above sea level, as high elevation reduces combustion performance.Low NOx heaters:Rated inputs are suitable for up to 5,000 feet elevation. For elevations above 5000 feet, consult the factory.

WARNING: This unit contains refractory ceramic fiber (RCF) insulation in the combustion chamber. RCF, asmanufactured, does not contain respirable crystalline silica. However, following sustained exposure to veryhigh temperatures (>2192F), the RCF can transform into crystalline silica (cristabolite). The InternationalAgency for Research on Cancer (IARC) has classified the inhalation of crystalline silica (cristabolite) as car-cinogenic to humans.

When removing the burners or heat exchangers, take precautions to avoid creating airborne dust and avoidinhaling airborne fibers. When cleaning spills, use wet sweeping or High Efficiency Particulate Air (HEPA)filtered vacuum to minimize airborne dust. Use feasible engineering controls such as local exhaust ventilationor dust collecting systems to minimize airborne dust. Wear appropriate personal protective equipmentincluding gloves, safety glasses with side shields, and appropriate NIOSH certified respiratory protection, toavoid inhalation of airborne dust and airborne fiber particles.

Page 12: Pool Heater

12

OUTDOOR HEATER INSTALLATIONThese heaters are design-certified for outdoor installation, when equipped with the approved tops designated foroutdoor use.WARNING: The heater shall not be located in an area where water sprinklers, or other devices, may causewater to spray through the cabinet louvers and into the heater. This could cause internal rusting or damageelectrical components, and void the warranty.

WARNING: Do not install within 3 feet of a heat pump or an outdoor condensing unit. Strong air intake fromthis type of equipment can disturb the combustion process and cause damage or personal injury.

HEATER WITH OUTDOOR STACKLESS TOP Pagoda Top Installation

1. Insert tabs into keyhole (4 places).

Pagoda Top(Shipped insidebox in heatercarton)

2. Snap tabs into keyholes so as not to pull out.

CLEARANCES

ALL HEATERSFor clearances from combustible surfaces, see thechart below.CLEARANCE FROMCOMBUSTIBLE CONSTRUCTION

INDOOR INSTALLATIONS:Top* - 30” (Drafthood) Back - 6”Front - Alcove (Open) Right Side - 12” (Water Side)Vent - 6” Left Side - 6”Floor** - 0” (Opposite Water Side)

OUTDOOR INSTALLATION:Top* - Unobstructed (Outdoor Stack)Top*** - 36” (Stackless Top)Floor - 0” Right Side - 12” (Water Side)Back - 6” Left Side - 6”

(Opposite Water Side)*Clearance from top of vent terminal.**Do not install on carpeting.***Clearance from top of heater.

When installed according to the listed minimum clear-ances from combustible construction, the pool heatercan still be serviced without removing permanentconstruction around the heater.

However for ease of servicing, we recommend a clear-ance of at least 24” in the front, and at least 18" on thewater connection side. This will enable the heater tobe serviced in its installed location, that is, withoutmovement or removal of the heater.

Clearances less than these (6” minimum), may requireremoval of the heater to service either the heatexchanger or the burner tray. In either case, theheater must be installed in a manner that will enablethe heater to be serviced without removing any struc-ture around the heater.

FLOORING: This heater can be installed on com-bustible flooring.

Pagoda Top

Page 13: Pool Heater

13

Heaters must not be installed under an overhang of less than three 3 ft from the top of the heater. Three sidesmust be open in the area under the overhang. Roof water drainage must be diverted away from the heatersinstalled under overhangs with the use of gutters.

For U.S. installations, the point from where the flue products exit the heater must be a minimum of 4 ft below,4 ft horizontally from, or 1 ft above any door, window or gravity inlet into any building. The top surface of theheater shall be at least 3 ft above any forced air inlet, or intake ducts located within 10 ft horizontally.

For installations in Canada, pool heaters shall not be installed with the top of the vent assembly within 10 ftbelow, or to either side, of any opening into the building. Refer to the latest revisions of CAN/CGA-B149.

4 ftMinimum

4 ftMinimum

1 ftMinimum

4 ftMinimum

3 ftMinimum

10 ftMinimum

Forced Air Inlet

For installations in Florida, that must comply with the Florida Building Code 2001, follow the directions on p14for the installation of hurricane tie-down brackets for all models.

Page 14: Pool Heater

14

FLORIDA BUILDING CODE 2001WIND SPEED = 150 MPH, 3 SECOND GUST

EXPOSURE = C

TOH

B

28”

40”

3” Min. Conc. Pad by others

3” Min. Conc.Pad by others

Min. EdgeDistance

Min. Edge Distance

(1)–1/4” x 1-3/4” S.S. Tapcon Bolt & Washer (Field Supplied)Ea. Pallet Anchor BracketUse hole closest to unit (4 total)

(1)–1/4” x 1-3/4” S.S. Tapcon Bolt & Washer (Field Supplied)Ea. Pallet Anchor BracketUse hole closest to unit (4 total)

2” x 6” x 1/8” PalletAnchor Bracket (4 Total) (Kit# 011636)

1/4” x 1-3/4” S.S. Tapcon Bolt & Washer (Field Supplied)NOTE: Use hole closest to unit withwasher overlapping edge of unit.

6”

6”

206/266/336/406 AtmosphericMODEL # B

206 20”266 23”336 26”406 29”

Page 15: Pool Heater

15

WARNING: Indoor heaters require a drafthood that must be connected to a vent pipe and properly vented tothe outside. Failure to follow this procedure can cause fire or fatal carbon monoxide poisoning.

INDOOR HEATER INSTALLATION

The heater is also design-certified for indoor installation when equipped with the approved drafthood.

For Canada, indoor installation is restricted to an enclosure that is not occupied and does not directly commu-nicate with an occupied area. Refer to the latest edition of CAN/CGA-B149 for specific requirements. Locateheater as close as is practical to a chimney or gas vent. Heater must always be vented to the outside. See VentPiping section (pg. 17-18) for details. Minimum allowable space is shown on the nameplate.

OUTDOOR STACK / INDOOR STACK

NOTE: The outdoor and indoor stacks are optional equipment and do not come standard with the heater.

OUTDOOR STACK KIT INCLUDES:(1) Drafthood, painted(1) Adapter plate(3) Mounting brackets (clips)(1) Top panel cover(2) 1-foot sections of metal tape(3) Screws(1) Instructions Clips

INDOOR STACK KIT INCLUDES:(1) Drafthood, unpainted(1) Adapter plate(3) Mounting brackets (clips)(3) Screws(1) Instructions

Clips

**REFER TO INSTALLATION INSTRUCTIONSINSIDE BOX FOR INSTRUCTIONS ON HOW TOINSTALL OUTDOOR/INDOOR STACK.

OUTDOORSTACK INDOOR STACK

Model Part No. Part No.206A/207A266A/267A336A/337A406A/407A

009834009835009836009837

009838009839009840009841

Page 16: Pool Heater

16

SPECIFICATIONS AND DIMENSIONS

HeaterModel

BTUHInput(000)

(A)CabinetWidth

(B)FlueDia.

(C)Indoor

Drafthood

(D) (J)Min. Gas

Conn.WaterConn.

Shipping Weights (lbs)

StandardHeater

w/StacklessTop

ASMEHeater

w/StacklessTop

IndoorDraft-hood

R206A 199.5 20” 6” 61-5/8” 10.0” 11-3/4” 3/4” 2” 187 206 12R266A 266.0 23” 7” 62” 11.5” 11” 3/4” 2” 210 229 15R336A 332.5 26” 8” 63” 13.0” 10-5/8” 3/4” 2” 230 249 17R406A 399.0 29” 9” 64-9/16” 14.5” 12-1/8” 3/4” 2” 249 268 20

ATMOSPHERIC UNITS

Designation for a Digital heater using propane gas is “EP”; a Digital heater using natural gas is “EN”.Designation for a Millivolt heater using propane gas is “MP”; a Millivolt heater using natural gas is “MN”.Prefix “C” is for cast iron (ASME) headers; “P” is for plastic (polymer) headers.Suffix “X” is for cupro-nickel tubing; “C” is for copper tubing.EXAMPLE: P-R406A-EN-X = Plastic headers, 406 model size, digital, natural gas, cupro-nickel.Reduce input 4% for each 1000 ft above sea level when installed above 2000 ft elevation.For Canada, no de-rating is required for elevations up to 4500 ftPlastic (polymer) headers cannot be used for ASME installations.*Note: For outdoor stack, use J dimension in the table above for appropriate size PLUS six (6) inches.

B

CINDOOR

DRAFTHOOD

38"

13-1/4"GAS

CONNECTION

J

A

26-5/8"(28-5/8" ASME)

32-11/16"ELECTRICAL

CONNECTION

40"STACKLESS

OUTDOOR TOP

28"

4-3/8"(3-3/8" ASME)

8-7/8"(6-5/8" ASME)

D

10"FLUE

LC

Amp Draw120 Volt 240 Volt

Digital 4 2

*

Page 17: Pool Heater

17

Low NOx UNITS

HeaterModel

BTUHInput(000)

(A)CabinetWidth

(B)FlueDia.

(C)Indoor

Drafthood

(D) (J)Min. Gas

Conn.WaterConn.

Shipping Weights (lbs)

StandardHeater

w/StacklessTop

ASMEHeater

w/StacklessTop

IndoorDraft-hood

R207A 199.5 20” 6” 55-5/8” 10.0” 11-3/4” 3/4” 2” 174 193 12R267A 266.0 23” 7” 56” 11.5” 11” 3/4” 2” 197 216 15R337A 332.5 26” 8” 57” 13.0” 10-5/8” 3/4” 2” 219 238 17R407A 399.0 29” 9” 58-1/2” 14.5” 12-1/8” 3/4” 2” 237 256 20

Designation for a Digital heater using natural gas is “EN”.Prefix “C” is for cast iron (ASME) headers; “P” is for plastic (polymer) headers.Suffix “X” is for cupro-nickel tubing; “C” is for copper tubing.EXAMPLE: P-R407A-EN-X = Plastic headers, 407 model size, digital, natural gas, cupro-nickel.For altitudes above 5,000 ft., consult the factory.For Canada, no de-rating is required for elevations up to 4500 ft.Plastic (polymer) headers cannot be used for ASME installations.*Note: For outdoor stack, use J dimension in the table above for appropriate size PLUS six (6) inches.

B

CINDOOR

DRAFTHOOD

31-13/16"

7-3/4"GAS

CONNECTION

J

A

20-1/2"(22-1/2" ASME)

34”STACKLESS OUTDOOR

TOP

28”

26-1/2”ELECTRICAL CONNECTION

4-3/8” (3-3/8” ASME)

8-7/8” (6-5/8” ASME) D

10"FLUE

LC

SPECIFICATIONS AND DIMENSIONS

Amp Draw120 Volt 240 Volt

6 3

*

Page 18: Pool Heater

18

B. All Air From Outdoors:When air is supplied directly from outside of build-ing, each opening shall have a minimum net freearea as noted:

COMBUSTION AND VENTILATION AIR(Indoor Units Only)

The heater must have both combustion and ventilation air. Minimum requirements for net free air supply open-ings are one opening that is 12 inches from the ceiling for ventilation, and one opening that is 12 inches from thefloor for combustion air as outlined in the latest edition of the National Fuel Gas Code, ANSI Z223.1(Canada-CAN/CGA-B149) and any local codes that may have jurisdiction.

CAUTION: Combustion air must not be contaminated by corrosive chemical fumes which can damage theheater and void the warranty.

A. All Air From Inside The Building:Each opening shall have a minimum net free areaas noted:

Model Square Inches Model Square Inches206/207 200 336/337 333266/267 266 406/407 399

Model Square Inches206/207 50266/267 67336/337 84406/407 100

VENT PIPING

Vent piping the same size as the drafthood outlet is recommended, however, when the total vent height is atleast 10 ft (drafthood relief opening to vent terminal), the vent pipe size may be reduced as specified in Chapter10 of the National Fuel Gas Code, ANSI Z223.1 (Canada - CAN/CGA-B149). As much as possible, avoid longhorizontal runs of vent pipe and too many elbows. If installation requires horizontal runs, the vent pipe must havea minimum of 1/4 in. per ft rise and should be supported at not more than five foot intervals. Plumbers tape,criss-crossed, will serve to space both horizontal and vertical piping. Gas vents supported only by the flashingand extending above the roof more than five feet should be securely guyed or braced to withstand snow andwind loads. We recommend use of insulated vent pipe spacers through the roofs and walls. Another option forinstallation that requires horizontal runs is using the D-2 power vent kit option.

The power vent assembly is a fan-assisted combustion system designed for application to models 206-407. Theunit, when installed as directed, is capable of operating in applications such as through-the-wall venting andreduced horizontal and vertical vent pipe sizes in new and current installations. The unit is factory-wired for 240VAC, with capability of rewiring for 120 VAC.

For protection against rain or blockage by snow, the vent pipe must terminate with a vent cap which complieswith the local codes or, in the absence of such codes, to the latest edition of the National Fuel Gas Code, ANSIZ223.1 (Canada - CAN/CGA-B149).

WARNING: Indoor heaters require a drafthood that must be connected to a vent pipe and properly vented tothe outside. Failure to follow this procedure can cause fire or fatal carbon monoxide poisoning.

Power Vent Kit

Model 120 VACPart No.

240 VACPart No.

206/207 010744 009832266/267 010744 009832336/337 010745 009833406/407 010745 009833 Optional Raypak D-2

Power Vent

For more information consult the D-2 Power Vent manual, (Catalog No. 6000.57.1).

The D-2 Power Vent oper-ates with a positve vent stat-ic pressure and with a ventgas temperature that pre-vents excessive condensateproduction in the vent, andas such, is a CATEGORY IIIappliance.

Page 19: Pool Heater

19

The discharge opening must be a minimum of 2 ft ver-tically from the roof surface and at least 2 ft higher thanany part of the building within 10 ft. Vent stack shall beat least 5 ft in vertical height above the drafthood out-let. The vent cap location shall have a minimum clear-ance of 4 ft horizontally from, and in no case below,unless a 4 ft horizontal distance is maintained, fromelectric meters, gas meters, regulators and reliefequipment.

The weight of the vent stack or chimney must not reston heater drafthood. Support must be provided incompliance with applicable codes. The heater top anddrafthood must be readily removable for maintenanceand inspection. Vent pipe should be adequately sup-ported to maintain proper clearances from combustibleconstruction.

Type "B" double-wall or equivalent vent pipe is recom-mended. However single-wall metal vent pipe may beused as specified in the latest edition of the NationalFlue Gas Code ANSI Z223.1 (Canada - CAN/CGA-B149).

GAS SUPPLY CONNECTIONS

Gas piping must have a sediment trap ahead of theheater gas controls, and a manual shut-off valve locat-ed outside the heater jacket. All gas piping should betested after installation in accordance with local codes.

CAUTION: The heater and its manual shut-off valvemust be disconnected from the gas supply during anypressure testing of that system at test pressures inexcess of 1/2 psi (3.45 kPa). Dissipate test pressurein the gas supply line before reconnecting the heaterand its manual shut off valve to gas supply line. FAIL-URE TO FOLLOW THIS PROCEDURE MAY DAM-AGE THE GAS VALVE. OVER PRESSURIZED GASVALVES ARE NOT COVERED BY WARRANTY. Theheater and its gas connections shall be leak testedbefore placing the appliance in operation. Use soapywater for leak test. DO NOT use open flame.

5' MIN

2' MIN

10' OR LESS

2' MIN

VENT CAP

VENT PIPE

DRAFT HOOD

HEATER

NOTE: Do not use Teflon tape on gas line pipe thread.A flexible sealant suitable for LP gases isrecommended.

A minimum of 7 in. WC and a maximum of 14 in. WCupstream pressure under load, and no-load conditionsmust be provided for natural gas or a minimum of12 in. WC and a maximum of 14 in. WC for propanegas.

SUPPLY PRESSURES

NOTE: With venting application of two or moreheaters, contact the factory.

Page 20: Pool Heater

20

GAS PRESSURE REGULATORThe gas pressure regulator is preset at 4.0 in. WCthroughout for natural gas, and 10.5 in. WC. forpropane gas. The pressure at the gas valve, takenwith a manometer, should be about 4.0 in. WC naturalgas (3.1 in. WC for Low NOx) and 10.5 in. WCpropane gas. If an adjustment is needed, remove sealand turn adjustment screw clockwise to increasepressure or counter-clockwise to decrease pres-sure.

NOTE: Low NOx gas valves are non-adjustable; set-ting was made at the manufacturer(Invensys/Robertshaw).

GAS PRESSURE ADJUSTMENT LOCATIONS

MILLIVOLT GAS VALVES

ELECTRONIC IGNITION GAS VALVES

Gas PressureAdjustment

Gas PressureAdjustment

Robertshaw 7000(Heater Models 206-406)

Honeywell VR8304(Heater Models 206-406 and 207-407)

ELECTRONIC IGNITION GAS VALVES-CONTINUED

Gas PressureAdjustment

Robertshaw 7200(Heater Model 206)

Robertshaw 7000 BDER(Heater Models 266-336)

Gas PressureAdjustment

Robertshaw 7000 DERHC(Heater Model 406)

PIPE SIZING FOR GAS CONNECTIONS

Robertshaw 7000 BDERF(Heater Models 207-407)

Non-AdjustableGas Valve

Maximum Equivalent Pipe Length (ft)Natural Gas 1000 BTU/FT3 0.60

Specific Gravity @ 0.5 in. WC Pressure DropPropane Gas 2500 BTU/FT3 1.53

Specific Gravity @ 0.5 in. WC Pressure DropInput 3/4” 1” 1-1/4” 1-1/2”

Model (KBTU) N P N P N P N P

206/207 199.5 25 60 90 215 360

266/267 266.0 15 35 50 125 210 480 445

336/337 332.5 10 20 30 80 140 320 290

406/407 399.0 * 15 20 55 95 225 215 480

*A 3/4” gas line can be used for up to 5 ft maximum length from thegas valve in addition to the sediment trap.

Page 21: Pool Heater

21

MODEL PIPE SIZE MIN. GPM MAX. GPM*206/207 1-1/4”–1-1/2” - 2” 20 125266/267 1-1/4”–1-1/2” - 2” 25 125336/337 1-1/4”–1-1/2” - 2” 35 125406/407 1-1/4”–1-1/2” - 2” 40 125

*When flow rates exceed maximum GPM an external auxil-iary bypass valve is required. See external bypass valvesection for details.

POLYMER HEADERS CAST IRON HEADERS (ASME)

FLOW RATES

HEAT EXCHANGER PRESSURE DROP TABLES

POLYMER HEADER (STANDARD MODELS)PLASTIC INTERNAL BAFFLE

(Manufactured after 11/08)FLOWGPM

PRESSURE DROP (FT OF HEAD)206/207 266/267 336/337 406/407

20 4.025 4.0 4.630 4.0 5.235 4.0 5.8 5.240 4.6 5.8 5.2 5.250 4.6 6.3 6.9 6.960 4.6 6.9 6.9 6.970 4.6 8.1 9.2 9.280 4.6 9.2 9.8 9.890 6.9 10.4 10.4 10.4100 8.1 11.0 12.1 12.1110 10.4 11.5 13.3 13.3120 11.0 12.7 17.9 17.9125 11.5 13.8 20.2 20.2

CAST IRON HEADER (ASME MODELS)FLOWGPM

PRESSURE DROP (FT OF HEAD)206/207 266/267 336/337 406/407

20 1.830 2.2 8.040 2.5 9.0 9.0 9.050 2.7 9.8 9.8 9.860 3.3 10.5 10.5 10.570 4.3 11.0 11.0 11.080 5.5 11.5 11.5 11.590 6.8 14.0 14.0 14.0100 8.2 17.0 17.0 17.0

Page 22: Pool Heater

22

CAST IRON HEADERS (ASME MODELS)

Heater must be located so that any water leaks will notdamage the structure of adjacent area. High tempera-ture 2" plastic pipe (CPVC) may be threaded directlyinto the header flanges. This is not the same as theSchedule 80 PVC pipe which is also gray. PVC may beused immediately after the supplied CPVC adapters.

DO NOT use petroleum-based assembly fluids (suchas petroleum jelly or lubricating oil). If assembly lube is

WARNING: NEVER install PVC directly into headerflanges. Use the 2" CPVC adapter supplied loosewith the heater.

INLET/OUTLET HEADER - ASME

Flange Gasket

Header FlangeUNITHERM GOVERNOR OPERATIONCAUTION:The patented Unitherm Governor is a thermostaticmixing valve specifically designed to maintain con-stant heater internal temperature between 105° and115°F despite continually changing flow rates fromthe filter and changing pool temperatures. This nar-row range is needed to prevent damaging condensa-tion on the burners which will occur if the heater runsfor any length of time below 100°F. It is also neededto inhibit scale formation in the tubes by maintainingtemperatures well below accelerated scaling temper-atures.

U.G. Plug(Polymer)

UnithermGovernor

Gasket

POLYMER HEADERS (STANDARD MODELS)Before attaching the 2-inch unions to the inlet/outletheader, make sure the O-rings are properly seated inthe grooves. Use AquaLube or equivalent non-petro-leum-based lubricant on the O-ring. Hand tighten theunions. Glue PVC piping directly to the unions.

INLET/OUTLET HEADER - POLYMER

High-temperature CPVC header flanges and headerflange nuts are provided. If there is any possibility ofback-siphoning when the pump stops, it is suggestedthat a check valve (or valves) also be installed in thesystem.

O-Ring

Header Flange(CPVC)

Header Flange Nut(CPVC)

GASKET DESIGN #1: Accepts 1-1/2" copper tube or1-1/4" galvanized pipe as a slip connection.GASKET DESIGN #2: Accepts 2" copper tube as aslip connection. The flange is threaded for 2" screw inpipe connections. Also used with the 2" CPVCadapters.

#1 #2

Header

Header Flange(Supplied)

CPVC Connector(Supplied)

Plumbing

required, use a silicon base such as AquaLube etc.

There are two sets of flange gaskets supplied withyour heater. Use the appropriate gaskets for all yourheater connections. Discard unused set.

NOTE: The State of Texas requires the addition of aflow switch and T&P gauge on ASME installations.Kit # 012011 can be ordered that will allow a standardASME unit to comply with the Texas code require-ments.

Page 23: Pool Heater

23

INTERNAL AUTOMATIC BYPASS VALVE

In addition to the Unitherm Governor, a built-in auto-matic bypass valve is provided in the in/out header.While the Unitherm Governor responds to the changesin water temperature in the heater, the internal bypassvalve automatically responds to changes in water pres-sure in the piping system. Proper amount of water flowis maintained through the heater under varying pres-sures dictated by the conditions of the pump and filter.

EXTERNAL AUXILIARY BYPASS VALVE(Where Required)An auxiliary bypass valve should be used when flowrates exceed 125 GPM. Usually a high-performancepump size larger than two horsepower will exceed thisflow rate. This valve is required to complement thefunction of the automatic bypass valve, particularlywhen starting the heater in winter or early spring whenthe spa or pool temperature is below 50°F. It alsoserves to eliminate needless pressure drop throughthe heater and accompanying reduction in the flow rateto the spa jets, etc.

From Heater To Heater

To Pool/ From Pool/Spa Spa

AUXILIARY BYPASS VALVE(DO NOT USE GATE VALVE)

Bypass Disc

SpringBypass Body

AUXILIARY BYPASS VALVE ADJUSTMENT

To set bypass: With clean filter, adjustment is made byfeeling the inlet and outlet pipes at the heater. Outletpipes should be slightly warmer than inlet and comfort-able to the touch. If pipe is hot, close bypass; if cold,open bypass.

PRESSURE RELIEF VALVE INSTALLATION

To conform to local building codes, it may be neces-sary to install a pressure relief valve. A 3/4" pressurerelief valve, having a capacity equal to the BTUH out-put of the model to be installed, is recommended forthis heater. The maximum acceptable pressure reliefvalve setting is 125 psi.

A 3/4" NPT connection is provided in the Polymerheader for installation of a pressure relief valve. Thevalve shall be installed in a vertical position. Do notovertighten. Install pressure relief valve hand tightplus 1/2 turn.

POLYMER HEADER(STANDARD MODELS)

Pressure Relief ValvePRV Discharge

Connection

In/Out HeaderFig. #2004

A 3/4" NPT connection is provided in the header forinstallation of a pressure relief valve. The valve shallbe installed in a vertical position.

CAST IRON HEADER(ASME MODELS)

NOTE: To avoid water damage or scalding due tovalve operation, drain pipe must be connected to valveoutlet and run to a safe place of discharge. Drain pipemust be the same size as the valve discharge connec-tion throughout its entire length and must pitch down-ward from the valve. No shut-off valve shall beinstalled between the relief valve and the drain line.Valve lever should be tripped at least once a year toensure that waterways are clear.

PRV

Page 24: Pool Heater

24

The heater requires water flow and positive pressure to fire and operate properly. It must therefore be installeddownstream of the discharge side of the filter pump. A typical installation is plumbed as follows:1. The inlet side of the filter is plumbed directly to the discharge side of the filter pump;2. The outlet side of the filter is then plumbed to the inlet of the heater; and3. The outlet of the heater is plumbed to the return line to the pool or spa. The pump, filter and heater are thus

plumbed in series (Salt generators and chemical feeders must be down stream of the pool heater).

Heater must be located so that any water leaks will not damage the structure of adjacent area. PVC pipe maybe glued directly into header unions (Standard models only).

CAUTION: An additional source of heated water, e.g. a solar system, must be connected to the main lineahead of the heater inlet pipe in order for it to act as the primary heat source. If the primary system providesadequate heat to maintain set-point, the heater will not fire. Be advised that the control panel will then displaysensed water temperatures downstream of the primary heating system, rather than the temperature of thewater exiting the pool.

Plumbing from the heater back to the pool or spa must not have any valves or restriction that could prevent flowwhen the pump is operating.

PLUMBING—WATER CONNECTIONS

Single Pool HeaterInstallation

Multiple Pool HeaterInstallation

Page 25: Pool Heater

25

HEAT EXCHANGER REVERSAL PROCEDURE - STANDARD MODELS

1. Remove right and left side access panels(Figure 1).

2. Disconnect wires at high limit, AGS (automatic gasshut-off), and pressure switch on the in/outheader (Figure 2).

3. Digital Models: Remove the thermostat tempera-ture sensor by loosening the compression fittingnut (Figure 3). Re-route the sensor to the left sideof the heater.

4. Millivolt Models: Remove the temperature sen-sor bulb and retainer clip from the sensor well(Figure 4). Re-route the sensor bulb to the left sideof the heater.

5. Remove (12) bolts holding the inlet/outlet andreturn headers to the tube sheets. Clean off tubesheet area where the gasket seats. Also clean offthe header and the gasket. Apply a non-petrole-um-based lubricant to the gasket such asAquaLube. Re-attach the headers to the oppositesides, making sure they are installed in an uprightposition (Figure 5). Do not over tighten. Torqueshould not exceed 7 ft/lb.

6. Reconnect high limit, AGS, and pressure switchwires.

7. Digital Models: Insert the temperature sensor inthe compression fitting and tighten 1/2 turn pasthand-tight.

8. Millivolt Models: Insert sensor bulb and retainerclip into sensor well.

9. Allow for water flow through the heater and checkfor leaks.

10. Re-attach access panels to the opposite sides.

For ASME Models call your factory representative.

Fig. #1

Fig. #2

Fig. #3

Fig. #5Fig. #4

Page 26: Pool Heater

OPTION LOCATIONLEFT SIDE FIELD WIRING

26

ATMOSPHERICWiring locations

LOW NOxWiring locations

ELECTRICAL WIRING

NOTE: If it is necessary to replace any of the originalwiring, use 105°C wire or its equivalent, and/or 150°Cwire or its equivalent, like the original wiring.

MILLIVOLT MODELSThe Millivolt models are equipped with a self-generat-ing electrical system in which the electrical current isprovided by a pilot generator. No external electricalconnections are required.

When installing a remote switch, do not exceed 10 ft ofwiring from the heater. Use 18-gauge stranded wire.

DIGITAL MODELS

The standard field-wiring connection is on the rightside of the heater.

To wire the heater from the left side, follow thesesteps :1. Remove the two (2) screws that hold the front door

to the heater. Remove and set aside door for bet-ter access to wiring.

2. Remove the four (4) screws that hold down thejunction box to the sway brace.

3. Remove the transformer cover located on the farright by removing one (1) screw.

4. Remove the two (2) screws that hold down thetransformer.

5. Remove the one (1) screw that holds down theground wires.

6. Disconnect P6 connector from PC board.7. Remove transformer from its current location and

relocate it on the far left side of the heater.8. Re-route all high-voltage wires and ground wires

through the left jacket side of heater.9. Re-install P6 connector, ground wires (SPG),

transformer, junction box, front door, and plug rightside with the left sideʼs grommet plug.

NOTE: 7/8" dia. holes not utilized on jacket and controlbox can be used for fireman switch, auxiliary controlinterface or power vent (D-2) wiring.

NOTE:Heaters are factory-wired for 240 VAC power supply.

The Electronic Intermittent Ignition Device automati-cally lights the pilot and main burners upon a call forheat. The heater is supplied with a dual-voltage trans-former for 120 VAC or 240 VAC input power hookup.

OPTION LOCATIONLEFT SIDE FIELD WIRING

CONTROL BOX(FACTORY MOUNTEDLOCATION)

SWAY BRACE

BONDING LUG (STANDARD LOCATION)

BONDING LUG (OPTIONALLOCATION)

CONTROL BOX (FACTORYMOUNTED LOCATION)

SWAYBRACE

BONDINGLUG(OPTIONALLOCATION)

BONDINGLUG(STANDARDLOCATION)

CAUTION: Heater must be electrically grounded andbonded. Bonding lug is provided loose with theheater. Install bonding lug on lower right or left sideof jacket as necessary for bonding the heater.Mounting hole is provided on the jacket.

NOTE: Failure to ground the heater electricallycould affect the heaterʼs electronics.

Page 27: Pool Heater

27

TRANSFORMER WIRING120 VAC WIRINGFor 120 VAC input power to the unit, connect the black wire to the “L1” or hot leg of the power supply. Connectthe white wire to the “Ret” or neutral leg of the power supply. Attach the wire nut to the red wire. There shouldbe no connection to the red wire for 120 VAC operation. For Low NOx pool heaters attach a wire nut to eachred wire independently.

240 VAC WIRINGFor 240 VAC input power to the unit, connect the black wire to the “L1” or hot leg of the power supply. Connectthe red wire to the “L2” or second hot leg of the power supply. Attach the wire nut to the white wire. There shouldbe no connection to the white wire for 240 VAC operation. For Low NOx pool heaters attach a wire nut toeach white wire independently.

Heater must be electrically grounded and bonded in accordance with local codes, or, in the absence of localcodes, with the latest edition of the National Electrical Code, ANSI/NFPA 70. (Canada - Canadian ElectricalCode, CSA C22.1, Part 1 and Part 2.)

120V ATMOSPHERIC HEATER 120V LOW NOx HEATER

SUPPLYSIDE

SUPPLYSIDE

RETURNor

NEUTRALRETURN

orNEUTRALHEATER

4 WIRESHEATER7 WIRES

GROUND

L1L1HOT

RED

RED

RED

BLACK BLACK BLACK

BLACKHOT

BLACK

GREENGREEN GREEN

GREEN

WHITE WHITE WHITE

WHITE

WHITE

240V ATMOSPHERIC HEATER 240V LOW NOx HEATER

HEATER4 WIRES HEATER

7 WIRES

GROUND

L1

L2

L1

L2RED RED

BLACK

BLACK

BLACK

HOT

RED RED

REDHOT

HOTBLACK

HOTBLACK

GREENGREEN GREEN GREEN

WHITE

WHITE

WHITE

SUPPLYSIDE

SUPPLYSIDE

NOTE: Input power to the heater (120 or 240 VAC) can be supplied from the load (pump) side of time clock ordirectly from the GFCI power source. It is preferred to make connection to the load/pump side of the timeclock. If using the switched GFCI power source, the heater could display false service indicators on the displaypanel if the pump is turned off.

NOTE: If the transformerʼs primary side is wired for 120 VAC and 240 VAC is applied, damage to the trans-former and PC board may result. Such damages are not covered under manufacturerʼs limited warranty.

Page 28: Pool Heater

28

WIRING DIAGRAM - MILLIVOLT (MECHANICAL THERMOSTAT)

Page 29: Pool Heater

29

WIRING DIAGRAM - DIGITAL MODELS - ATMOSPHERIC

Page 30: Pool Heater

30

WIRING DIAGRAM - DIGITAL MODELS - LOW NOx

Page 31: Pool Heater

31

SECTION 4 - SERVICING INSTRUCTIONSGENERAL LOCATION OF CONTROLS

ATMOSPHERIC

LOW NOx

Digital ThermostatCircuit Board

Drain Plug(Located in rear header)

Unitherm Governor

Mounted On TopOf Header

HL1 - High LimitHL2 - High LimitPressure SwitchTemp Sensor/Well

Pilot

Roll-OutSwitch

Gas Valve

Transformer

Draw Plug

Drain Plug(Located in rear header)

UnithermGovernor

Mounted On TopOf Header

HL1 - High LimitHL2 - High LimitPressure SwitchTemp Sensor/Well

Pilot

Roll-OutSwitch

(Manual)

Gas Valve

Transformer

Draw Plug

AirSwitch

BlowerHose

Blower

Digital ThermostatCircuit Board

Page 32: Pool Heater

32

CONTROL PANEL REMOVAL

1. Remove screw from front door. Set aside door forserviceability.

CONTROL ADJUSTMENTS - MILLIVOLT MODELSThe water temperature is controlled by the heater ther-mostat on the upper front panel of the heater. Thecontrol center contains an On/Off switch and one ther-mostat.

The thermostat is fitted with a means of limiting theupper temperature limit below the maximum level.The knob stop adjustment ring illustrated below isadjustable by loosening the set screw, rotating theknob stop ring to the desired location and re-tighteningthe set screw.

SPA TEMPERATURERANGE

POOL TEMPERATURERANGE

KNOB STOP RING SET SCREWSTAND-BY

TEMPERATURE

KNOB STOP SHOWN ABOVE ISIN THE SPA TEMPERATURE RANGE

KNURLEDSCREW

Temp Adjust Buttons

Mode Button

LCD Display

ONOFF

2. Remove (4) screws from sides of control panel.3. Rotate control panel down until panel stops. Do

not force.NOTE: Caution must be used to not damage controls

or wiring.

CONTROL ADJUSTMENTS - DIGITAL MODELS

Page 33: Pool Heater

33

THERMOSTAT CONTROL OPERATIONThe pool heater thermostat, located on the upper frontpanel of the heater, controls the pool/spa water tem-perature. This control center contains a mode button,up and down temperature adjustment buttons, and anLCD display.

Mode ButtonThe MODE button functions as a means to turn theheater off or on in either the POOL or SPA setting. TheLCD display indicates the mode the heater is in andthe actual water temperature.

Temp ButtonsIf the heater is in POOL or SPA mode, the desiredwater temperature (SETPOINT) will also be displayedand may be changed using the UP or DOWN buttons.A manual toggle switch is also provided right below theMODE button to allow the heater to be turned off.

OperationIn the POOL or SPA modes, the actual water temper-ature is displayed along with the desired water temper-ature (SETPOINT). If the heater is firing, a flame iconwill be visible.

To adjust the setpoint temperature, make sure the con-trol is in the appropriate mode (POOL or SPA) andpush the UP or DOWN buttons.

Fault History FileTo access the Fault History File, press the Mode but-ton until the display reads OFF. Press both the “UP”and “DOWN” buttons at the same time (5-7 seconds)until the display changes and shows a fault code. Thelatest fault code will be displayed first. By pressing the“UP” or “DOWN” buttons, a series of faults will be dis-played from the last (highest number) to the first (low-est number). If the buttons are not touched after 5-7seconds, the display will return to its normal operation.

Actual WaterTemperature

Setpoint Temperature

Flame Icon

ModePool or Spa

DIGITAL THERMOSTAT CONTROLS

Thermostat operationYour heater is equipped with a microprocessor-controlled thermostat that controls the pool or spa temperatureby measuring the temperature of the water coming back through the heater. It will then monitor the water tem-perature and turn the heater back on when it senses that the water temperature is falling below the set point. Itis normal to experience small fluctuations in the return water temperature during the operation of the heater.The thermostat is calibrated with a very narrow tolerance to ensure accuracy of the set temperature. Thus,slight fluctuations in water temperature may cause your heater to cycle on and off frequently. This isnot a problem. It will not harm the heater nor interfere with the thermostatʼs ability to precisely control the tem-perature of the pool or spa.

WATERTEMP

SETPOINT

MODE

TEMP

LCD Display Temp Buttons Mode Button Program button

DISPLAY CALL FOR HEAT

Page 34: Pool Heater

34

Resets board to factory default settings.

Resets faults in the History File.

Change from Fahrenheit to Celsius.

SPA setpoint maximum adjustment.

POOL setpoint maximum adjustment.

SETdef – Default SettingsRefer to step one above to access the programscreen. SETdef should appear on the screen. If not,press the Mode button until SETdef appears on thedigital display. Press and hold both “UP” and “DOWN”buttons for 5-7 seconds until 3 dashes (---) appear.This operation resets the operating program to its fac-tory default values. Both the POOL and SPA setpointswill revert to 65°F (18.5°C) and both POOL and SPAmaximum temperature settings will be 104°F (40.0°C).Once this is done, reassemble the control panel.

RESfl – Reset Fault HistoryRefer to step one above to access the programscreen. Press the Mode button until RESfl appearson the digital display. Press and hold both “UP” and“DOWN” buttons for 5-7 seconds until 2 dashes (--)appear. This operation resets the Fault History file to“0” and clears all the stored faults. Once this is done,reassemble the control panel.

Program Button1) To access the program screen, press the Mode

button until the display reads OFF. Remove thefour screws holding the control cover on. Swingcontrol panel down so the back side of the boardis visible (see page 30). Locate the Program Modebutton as shown in the figure on pg. 32. Press theprogram button (5-7 seconds) until SETdefappears on the digital display. Release the pro-gram button.

2) Press the Mode button sequentially until thedesired program event is reached. There are 5 dif-ferent events that can be programmed. Theyappear in the sequence listed below:

F/Cfff – Fahrenheit to CelsiusRefer to step one above to access the programscreen. Press the Mode button until F/Cfff appears onthe digital display. The digital display is capable of dis-playing Celsius as well as Fahrenheit temperatures.The “UP” or “DOWN” buttons will select “F” or “C” onthe temperature display. Choose the desired tempera-ture scale. Once this is done, reassemble the controlpanel.

SETspa 104 – SPA Set Point Maximum AdjustmentRefer to step one above to access the programscreen. Press the Mode button until SETspa 104appears on the digital display. Using the “UP” and“DOWN” buttons will change the MaximumTemperature Setting to your desired value. The con-trol can be set for a maximum of 107°F. Once this isdone, reassemble the control panel.

SETpool 104 – POOL Set Point Maximum AdjustmentRefer to step one above access into the programscreen. Press the Mode button until SETpool 104appears on the digital display. Using the “UP” and“DOWN” buttons will change the MaximumTemperature Setting to your desired value. The con-trol can be set for a maximum of 107°F. Once this isdone, reassemble the control panel.

Page 35: Pool Heater

35

If the PRS fault code is displayed, it indicates thatthere is insufficient water flow through the heater.Make sure the pool filter and pump strainer are cleanbefore calling a service representative.

DIAGNOSTICSThe digital thermostat models are equipped with on-board diagnostic controls. If there is a safety fault, afault code will be displayed along with a serviceindication.

READING A FAULT

The word “SERVICE” will flash on and off if the PCboard detects a known fault. The fault will be dis-played in three big letters on the lower left of the dis-play.

Service WillFlash3 Letter

Fault CodeSee tablefor faultdefinition

STATUS CODESDisplay DefinitionCFH Call for heatCLK Time clockEOL End of line test (Factory Use Only)LON Low NOx UnitOFF Off modePRO Propane gas configuredREM Remote control activatedSPK SparkSPR Spare fault code indicator

FAULT CODESDisplay DefinitionBD1 Board failureEEP Microprocessor errorFAN Blower pressure failureFFL Flame sensing when pilot and gas

valves are closedGVC Gas valve closedGVO Gas valve openHL1 High limit switch #1 openHL2 High limit switch #2 openIGN Ignition failureILO Ignition lockout - Propane units onlyPRS Water pressure switch openROL Heat roll-out safety switch openSNS Sensor failure, Water temp. below 36°F

or above 110°FVNT Vent switch open - This is jumped from

the factory.

PROGRAM MODESDisplay DefinitionCCC Celsius settingF/C Change from Fahrenheit to CelsiusFFF Fahrenheit settingRES Reset defaultsSET Set point max adjustment

NOTE: The LCD temperature display may not agree with the temperature reading of your pool or spa ther-mometer. The heater reads the water temperature at the inlet. Due to the circulation characteristics of any poolor spa, the water temperature at the inlet to the heater may differ from that observed at a given location in thepool or spa.

Page 36: Pool Heater

36

REMOTE CONTROL INSTALLATION AND OPERATIONCAUTION: Before installing remote controls to the digital thermostat model heaters read the following:The digital thermostat model is remote-ready in most cases. The digital liquid crystal display (LCD) shows theactual pool temperature, operating status, and service codes (See examples below). The touch pad on the con-trol panel allows you to select the desired pool or spa temperature. It also indicates when a remote system iscontrolling the heater by displaying REM in the display. When connecting the heater to a remote system, iden-tify whether it is a two- or three-wire remote system. Select the appropriate instruction listed below to properlyinstall the remote to the heater.

REMOFF Mode Heating in the POOL Mode Heating in the SPA Mode Remote Mode

REMOTE OPERATIONThe digital model heaters are equipped with the abili-ty to work with external remote controls. The supplied7-pin remote wiring connector supplies power out toeither a toggle switch or the switch contacts of a thirdparty remote. The remote works by either making orbreaking the circuit created by the remote wiring.Typically, a remote does not supply power to theheater, it only provides a switching function to turn theheater On or Off. If your remote is suppling its ownvoltage to the heater, it will not work with thisheater and may damage the digital circuit board.

For operation of the heater using the onboard thermo-static controls with a time clock, see the “Time Clock /Firemanʼs Switch” section.

ACTIVATING THE REMOTEThe digital thermostat heaters have the ability to dis-connect from the remote it is wired to. To activate ordeactivate the remote follow these steps:

Note: Electrostatic Discharge (ESD) damage can be caused bydirect or indirect contact with the wiring or circuit board. Whenone walks to the heater area, an electrostatic charge accumu-lates on the body. Contact of a finger allows the body to dis-charge, possibly causing device damage. This damage can belimited if the service person discharges himself, following ESDpreventive/removal practices, and holds on to the heater enclo-sure for 5 seconds before proceeding.

WATERTEMP

SETPOINT

MODE

TEMP

Press and hold all three buttons for 5 to 7 seconds.

The digital display format will change and indicateREMoFF or REMOn.

Pool Common(BLK/ORN)

Spa Common(ORN/BLK)

24VAC HOT(BLU)

7-PIN RemoteInterface Harness

NOTE: When in remote operation, the keypadmode and temp buttons are disabled. Remote willflash even when the unit is off.

REMOn = External remotecontrol active (display will flashREM)

REMoFF = Remote disabled(heater thermostat will controlheater - use this mode to testheater operation)

Page 37: Pool Heater

37

REMOTE CONTROL WIRINGImportant Installation Notes for Remote or External Wiring Configuration• Remote wiring must be run in a separate conduit.• Remote wiring must not be run parallel to high voltage lines.• For runs of under 30 feet, remote wiring should have stranded conductors with a minimum of 22 AWG, 600V,

cable twisting 1.5 to 2.5 in. lay and jacketed.• For runs over 30 feet, the conductors should be a minimum of 20 AWG, 600V, cable twisting 1.5 to 2.5 inch

lay that is shielded and jacketed.• Maximum cable length is 200 feet.• For both two- and three-wire remote systems, the provided 7-pin wiring connector must be utilized. Please

refer to the wiring instructions.

Note: The remote wires must be connected to the 7-pin connector beforethe connector is plugged into the board.

2-Wire Remote Control (On-Off)This application assumes that only one heating function (pool or spa) is required.

1. Turn on power to the heater.2. For a 2-Wire Remote Control from a remote without

its own sensor, push the mode button to the “POOL”or “SPA” mode and set the desired setpoint (eg. 102°F for spa).

3. For a 2-Wire Remote Control from a remote with itsown sensor, push the mode button “POOL” or “SPA”mode and set the temperature to the highest settingavailable on the control. The actual setpoint will becontrolled by the remote control.

4. Turn the mode button to "OFF" and remove powerfrom the heater.

5. On the "Remote Interface Harness", connect theBLUE wire to one side of the "REMOTE" switch andconnect the other side to either the ORANGE/BLACKwire for "SPA" operation or the BLACK/ORANGEwire for "POOL" operation.

6. Attach wire nut on unused wire to the "RemoteInterface Harness."

7. Install the "7-Pin Remote Interface Harness" to theP8 connector and turn power “On” to the heater.

See instructions on previous page to activate theremote control.

3-Wire Remote Control Using Three-Position Switch (Pool-Off-Spa, or Low-Off-High)This application assumes that both heating functions (pool and spa) are required.

1. Turn on power to the heater.2. Push the mode button to the "POOL" or "SPA"

mode and set the desired temperature for each(eg. 80°F for Pool and 102°F for Spa).

3. Turn the mode button to "OFF" and remove powerfrom the heater.

4. On the "Remote Interface Harness" connect theBLUE wire to one side of the "REMOTE" switchand connect the ORANGE/BLACK wire for "SPA"operation and the BLACK/ORANGE wire for the"POOL" operation.

5. Install the "Remote Interface Harness" to the P8connector and turn power "ON" to the heater.

See instructions on previous page to activate theremote control.

Wire Nut - BLK/ORNTo Pool (COMM)

ORN/BLK - To Spa (COMM)

BLU - 24VAC

BLK/ORN - To Pool (COMM)

ORN/BLK - To Spa (COMM)

BLU - 24VAC

P8 Connector

P8 Connector

Page 38: Pool Heater

FLAME ROLL-OUT SAFETY SWITCHAtmospheric heaters areequipped with a thermal cutoffdevice to prevent flame roll-outin the event the heat exchang-er becomes blocked. This is a"single-use" type fusible link orthermal fuse, that must bereplaced when disabled by an

over-temperature condition, caused by excessiverestriction in the heat exchanger flue passage.

HIGH LIMITSThe heater is equipped with two automatic high limits.Both are located in the inlet/outlet header. Both are setto open at 135°F.

38

1. Make sure the pool filter isclean before adjusting theswitch.

2. Set the heater control to theOFF mode.

3. Turn the filter pump on andconfirm that the pressure

TWO-SPEED PUMPSIn some cases, the flow on the low-speed is insufficientto operate the heater. This is apparent when the waterpressure switch cannot be further adjusted or if theheater makes banging noises or shuts off on high limit.In these cases, the pump must be run at high speedwhen heating the water.

PRESSURE SWITCHADJUSTMENT RANGE

CAUTION: Do not operate the heater without thefunction of a properly adjusted water pressure switchor flow switch.

5 FT.MAX POOL OR SPA

MAY REQUIRE ADJUSTMENTFOR LOWER PRESSURE

MAY REQUIRE ADJUSTMENTFOR HIGHER PRESSURE

5 FT.MAX

switch is closed (use a multimeter to check). If thepressure switch fails to close, either the switch set-ting is too high or not enough pressure is beingsupplied by the filter pump.

NOTE: If heater is installed outside of the limitsshown, a higher pressure rated (11 psi) switch may beused. A flow switch, mounted and wired adjacent to theheater, may be used in place of the factory-mountedpressure switch. See Parts List (pg. 51) for 11 psiwater pressure switch.

WATER PRESSURE SWITCHThe water pressure switch, or heater actuator, ensuresthat the heater operates only when the filter pump is inoperation. It is located on the inlet/outlet header. It isfactory set at 1.75 PSI for deck-level installations.When the heater is located below the level of the spaor pool, it may be necessary to adjust the pressureswitch to compensate for the no-flow static head. If itis necessary to adjust the water pressure switch, uti-lize the following procedure:

WATER PRESSURE SWITCH ADJUSTMENT

AdjustmentKnob

TIME CLOCK/FIREMANʼS SWITCH 4. Turn the heater ON.5. Manually turn the pressure adjustment knob clock-

wise until the heater shuts off. (A flat screwdrivermay be necessary if knob is too tight.)

6. Slowly turn the adjustment knob counter-clockwiseuntil the heater calls for heat again.

7. Turn an additional 1/2 turn counter-clockwise.8. While the heater is running, check the adjustment

by turning the pump off and on several times. Theburners should shut off immediately when thepump is turned off. If it does not, repeat the abovesteps until proper operation is observed.

To operate the heater with a time clock, connect thetimer to the firemanʼs switch connection in the heaterʼswiring. The time clock should be of the dual switchtype and set to shut off the call for heat to the poolheater 15 to 20 minutes prior to shutting down the poolpump. On millivolt heaters the firemanʼs switch con-nection is a wire nut located in the Violet/Black wiringbetween the manual toggle switch and the gas valve.For digital heaters the firemanʼs switch connection islocated on the 14 pin header connected to the digitalcontrol board. Splice into the red wire jumper tagged“Where necessary add “Firemanʼs” switch circuit here”to connect the time clock. The firemanʼs switch con-nection on both millivolt and digital heaters mustbe a dry contact and must not supply power to theheater. Powering the firemanʼs switch connectionexternally may damage the heater, and is not cov-ered by warranty.

Millivolt heaters: Do not exceed 15ft of total wiringusing 14 AWG stranded copper wire rated for 105ºC(221ºF) minimum.

Digital heaters: Do not exceed 50ft of total wiringusing 18 AWG stranded copper wire rated for 105ºC(221ºF) minimum.

NOTE: When using a time clock, the heater will dis-play “CLK” when the firemanʼs switch is open, indicat-ing that the time clock has shut off the call for heat.

Page 39: Pool Heater

MAIN BURNER AND ORIFICE REMOVAL -ATMOSPHERIC MODELS

1. Remove burner tray.2. Remove screws and burner hold-down bracket.

NOTE: If the heat exchanger is sooted badly, theburner hold-down bracket and spacer can become dis-torted from direct-flame impingement and this usuallynecessitates replacement of these parts.

3. Lift burners from slotted spacers and slide from ori-fices. Clean with a wire brush.

4. Orifices usually do not need to be replaced. Toclean, run either copper wire or wood toothpickthrough orifice. Do not enlarge hole. To removeorifice, use a socket wrench and remove frommanifold. DO NOT overtighten when reinstalling.

39

PILOT

BURNER

BURNERHOLD-DOWN

BRACKET

GASORIFICE

GAS VALVE

BURNER TRAY REMOVAL -ATMOSPHERIC MODELS1. Shut off main electrical power switch to heater.2. Shut off gas upstream of heater.3. Remove front door.4. Disconnect gas line from gas valve.5. Remove (2) screws that mount burner tray to unit,

and (2) screws that secure gas valve to jacket.6. Disconnect wires that terminate at gas valve.7. Disconnect hi-tension wire from PC board.8. Slide out burner tray.9. Reverse above procedure to reinstall.

GAS VALVE REMOVAL -ATMOSPHERIC MODELS1. Shut off gas supply to the heater. Remove gas

piping to gas valve inlet.2. Disconnect wires, pilot tubing and bleed line, if

required.3. Remove burner tray from heater.4. Turn vertical gas pipe from manifold slightly and

unscrew gas valve.5. Reverse above procedure to reinstall.

HIGH LIMIT REMOVAL

1. Shut off main electricalpower switch to heater.

2. Remove inlet/outletinspection panel.

3. Remove defective highlimit and replace with anew high limit.

4. Replace inspection panel.

PILOT SAFETY - Millivolt ModelsHeaters equipped with the standing pilot (millivolt sys-tem) have pilot generators which act as a safetydevice to shut off the flow of gas to the main burnersand the pilot burner in case the pilot flame is extin-guished. The pilot burner must be manually re-lightedto place the heater in operation again. Refer to thelighting instructions provided on the heater label.

PILOT SAFETY - Digital ModelsThe heater employs a pilot safety which closes themain gas valve within 8/10ths of a second wheneverthe pilot flame is interrupted. The pilot flame is auto-matically lit when the device is powered. The heaterperforms its own safety check and opens the mainvalve only after the pilot is proven to be lit.

206-406Atmospheric

NOTE: An erratic high limit is often characteristic of aninternal heat exchanger problem, e.g. scale build-up,defective bypass. Refer to Troubleshooting section (onpg. 42).

PILOT REMOVAL AND CLEANING1. Disconnect pilot tubing and wires from gas valve.2. Remove pilot assembly from burner tray.3. Remove pilot from bracket.4. Remove pilot orifice and air opening (Honeywell

MV unit only), and clean with wire or small brush.

CAUTION! Do not enlarge hole in pilot orifice.

5. Reverse above procedure to reinstall.

Pilot Pilot

AirOpening

Orifice

Orifice

HONEYWELL MILLIVOLTPILOT

ROBERTSHAW MILLIVOLTPILOT

Page 40: Pool Heater

(Millivolt and ASME)1. Shut off water to heater and drain heat exchanger.2. Remove access panel on water connection side.3. Remove old immersion well with bushing and

sleeve.4. Install replacement well in header.

NOTE: Installation in polymer header should be handtight plus 1/2 turn.

Well Assembly

40

Soot will clog areas between fins and cause eventualtube failure. Any sign of soot at the base of the burn-ers or around the outer jacket indicates a need forcleaning.1. Remove top and flue collector from cabinet.2. Remove "V" baffles from heat exchanger.3. Remove burner tray. (See pg. 38).

Extension Pieces (2) Auger with Carbide Tip Wire Brush

WARNING: SOOT IS COMBUSTIBLE. EXERCISEEXTREME CARE.

HEAT EXCHANGER REMOVAL1. Shut water, gas and electricity off, close valves

and relieve pressure, then remove relief valve.Remove side inspection panels.

2. Remove top jacket holding screws.3. Remove rear top panel.4. Remove screws mounting the rain shield to the

rear panel. Also remove the screws that mount therain shield to the sway brace. Remove rain shield.

5. Remove the four (4) screws holding down the fluecollector. Remove the flue collector.

6. Disconnect flange nuts on Inlet/Outlet header,loosen union(s) at gas pipe and slide heater awayfrom piping.

7. Lift heat exchanger straight up using caution not todamage refractory.

8. Reverse above procedure to reinstall. Make surethe insulation strips are properly replaced on top ofthe refractory retainer.

TUBE CLEANING PROCEDUREEstablish a regular inspection schedule, the frequencydepending on the local water conditions and the sever-ity of service. Do not let the tubes clog up solidly.Clean out deposits over 1/16" in thickness.

The heater may be cleaned from the return headerside, without breaking pipe connections. It is prefer-able, however, to remove both headers for better visi-bility through the tubes and to be sure the ground-uplime dust does not get into the system.

Note that you do not remove the top panel or theheater exchanger, generally.

After reaming, mount the wire brush in place of theauger and clean out debris remaining in the tubes.

Another method is to remove the heat exchanger,ream tubes and immerse heat exchanger in non-inhib-ited de-scale solvent for severe scale build-up.

DESOOTING PROCEDURE

4. Remove heat exchanger from the heater and washwith a garden hose, making sure soot is removedfrom spaces between fins.

5. Reverse above procedure to reinstall.

NOTE: In extreme cases it may be necessary to dosteam cleaning at the local car wash. DO NOT WIREBRUSH.

COMBUSTION CHAMBER REMOVALTo remove combustion chamber, you must first haveremoved the heat exchanger.

REFRACTORY PANELS - TOP VIEWAtmospheric Heaters Low NOx Heaters

IMMERSION WELL REPLACEMENT

Page 41: Pool Heater

41

The Low NOx pool heaters are certified and testedunder the ANSI Z21.56/CSA 4.7 Standard for Gas-Fired Pool Heaters.

The heater should be installed to meet all local codes,and the latest editions of the National Fuel Gas CodeZ223.1 and the National Electrical Code, ANSI/NFPA70.OPERATION

On call for heat, the ignition system, consisting of anelectronic spark module, gas valve and pilot system, isenergized. Providing the pilot is proven, the blowerwill start running, the main gas valve will open and theheater will operate. When the operating control is sat-isfied the heater will shut down.

START-UP PROCEDURES1. Turn on power to the heater with gas supply off.2. Turn on gas supply.3. Set controller to call for heat.4. System should start as follows:

a. Spark will turn on, pilot gas valve will open, andthe blower will begin running.b. Once the blower provides pressure, the maingas valve will open.c. Heater will operate until call for heat is satisfied.

deck under cold-start conditions. After about five min-utes of operation, the flames should settle down andblue tips should become visible. Lifting of flamesbeyond five minutes would indicate too much combus-tion air.

VISUAL INSPECTIONFlames can be observed through the slot openingabove the plenum. Flame color is blue and evenlyspread on the top surface of the burner. At least everythree months a visual inspection should be made ofthe burners.

ELECTRICALBe sure that electrical service to the heater has prop-er overload fuse or circuit breaker protection, wire sizeand connections which comply with all applicablecodes.

FLAME ROLL-OUT SAFETY SWITCHLow NOx heaters are equipped with a thermal cut-offdevice to prevent flame roll-out in the event the heatexchanger becomes blocked. It is a "manual reset"type roll-out switch that must be reset by a servicetechnician after any over-temperature conditions havebeen fixed. Excessive restriction in the heat exchang-er flue passage may cause the switch to disable theheater.

LOW NOx POOL HEATERS

NOTE: Door must be in place for proper operation.

Retainer Plug

U.G.Spring

Gasket

To test the operation of the Unitherm Governor, placein hot water (over 110°F) and watch for movementagainst spring. If there is no movement, replace unit.

Manual Reset Switch

BLOWER ADJUSTMENTThis Low NOx pool heater is equipped with a combus-tion air plate (baffle) mounted on the air intake to thecombustion air blower. The baffle has a hole that is uti-lized to control the air inlet to the blower.

When the combustion air setting is proper, there will besome lifting of the flames on some areas of the burner

UNITHERM GOVERNOR (U.G.) REPLACEMENT1. Shut water, gas and electricity off, close valves

and relieve pressure.2. Drain heat exchanger.3. Remove retainer plug located next to the outlet

pipe connection.4. Unsnap old U.G. to remove from retainer plug.

Snap in new U.G.5. Reinstall retainer plug, taking care to lubricate

gasket with a non-petroleum based grease suchas AquaLube.

Page 42: Pool Heater

42

LOW NOx HEATERS (CONTINUED)

BURNER TRAY REMOVAL

1. Shut off main electrical power switch to heater.2. Shut off gas upstream of heater.3. Remove front door.4. Disconnect gas line from gas valve.5. Remove (2) screws that mount burner tray to the

base of the unit, and (2) screws that mount theblower box to the burner tray, and (1) screw thatsecures the anti-rotation bracket to the heater.

6. Disconnect wires that terminate at gas valve.7. Unscrew (4) screws that secure the control box.8. Disconnect pilot wire from the pilot assembly.9. Disconnect wire connector from the combustion

blower.10. Carefully slide out the burner tray assembly.11. Reverse above procedure to reinstall.

GAS VALVE REMOVAL

1. Remove burner tray, following above procedure.2. Disconnect, pilot tubing from gas valve.3. Remove (2) screws that mount anti-rotation

bracket to the burner tray.4. Turn vertical gas pipe from manifold slightly and

unscrew gas valve.5. Reverse above procedure to reinstall.

PILOT REMOVAL

1. Disconnect pilot tubing from gas valve.2. Remove the pilot wire from the pilot assembly.3. Remove (2) screws that mount the pilot assembly

to the burner tray.4. Pull the pilot assembly downwards and outwards.5. Reverse above procedure to reinstall.

COMBUSTION BLOWER REMOVAL

1. Remove the (2) screws that secure the blower boxto the burner tray.

2. Remove (2) screws that mount the blower box tothe base of the heater.

3. Disconnect wire connector from the combustionblower.

4. Carefully remove blower box with combustionblower.

5. Remove (2) screws that secure combustion blow-er to blower box.

6. Reverse above procedure to reinstall.

Low NOx Horizontal Pilot

BURNERHOLD-DOWNBRACKET

LOW NOxBURNER

PILOT

BAFFLE MOUNTEDINLET SIDE

COMBUSTIONAIR BLOWER

GAS ORIFICE

GAS VALVE

207-407Low NOx Burner Tray

MAIN BURNER AND ORIFICE REMOVAL

1. Remove burner tray, following above procedure.2. Remove pilot. See pilot removal procedure.3. Remove (8) total screws from the burner hold-

down brackets, front and rear of tray.4. Remove (8) total screws from the left and right

sides of the manifold assembly. Detach the air/gasmanifold assembly from the burner tray assembly.

5. Remove burners by raising them straight up off therear end slots.

6. Use a long 9/16” socket wrench to remove orificefrom the gas manifold.

7. Reverse above procedure to reinstall.Electrode AlignmentDetail

Page 43: Pool Heater

43

MECHANICALIMPORTANT NOTICE These instructions are intended for the use of qualified personnel who are specifically trained and experienced in theinstallation of this type of heating equipment and related system components. Installation and service personnel may be required by somestates to be licensed. Persons not qualified shall not attempt to install this equipment nor attempt repairs according to these instructions.

PROBLEM CAUSE SOLUTION

Harmonics, or whining noise U.G. inoperative................................... Check movement by putting in hot water (110°F or higher).If no movement, replace.

*Debris or restriction in system............ Locate the restriction and remove. Flush system and clean.*Debris in gas line................................ Remove debris or blow out gas line.Low flow............................................... Scale forming in heat exchanger - clean heat exchanger and

check pool pH and total alkalinity.

Heater going on and off Dirty filter.............................................. Clean or replace filter.continuously Low water level in pool........................ Raise water level.

External bypass setting out ofadjustment............................................ Adjust bypass.*Pressure switch out of adjustment..... Adjust pressure switch.

Liming or scale forming in Pool water............................................ See Water Chemistry on page 2.exchanger Bypassing too much water................... Inspect bypass for movement, if no movement, replace.

U.G. not functioning............................. Replace if no movement when heated.

Sooting High flow rates..................................... Reduce by adding manual bypass valve.Adjust manual bypass valve until heater outlet watertemperature is between 105°F and 110°F.

U.G. Inoperative................................... Check movement by putting in hot water (110°F or higher).If no movement, replace.

*Air starvation....................................... Refer to installation instructions.*Improper venting................................ Follow recommended installation instructions.*Insects or debris clogging

burner intake ports............................. Clean burners.

Pilot outage Low gas pressure................................ Adjust gas pressure.Restricted pilot..................................... Clean pilot.Weak pilot generator............................ Replace pilot.

Yellow lazy flame Low gas pressure................................ Adjust gas pressure.*Insects or debris cloggingburner intake ports............................... Clean burners.

Outer jacket very hot *Broken refractory caused by(paint blistered) shipping damage or improper

combustion......................................... Replace refractory panels.Excessive sooting of heat exchanger.. Determine cause of sooting & correct.

Takes too long to heat Under-sized heater............................... Calculate heating capacity of heater:pool or spa Htr. output(BTUH)

Pool gallonage x 8.33 or refer to heater sizing chart.This does not take into account heat loss due to weather.

Filter not running long enough............. Reset time clock.Dirty filter.............................................. Clean filter.Gas line or meter undersized............... Refer to installation instructions.

Leaking at well Overacid............................................... Replace well and maintain proper water chemistry.

Leaking at heat exchanger Overacid............................................... Replace heat exchanger and maintain proper water chemistry.

Gasket brittle and leaking - Heater running after pump shuts off.... See Pressure Switch Adjustment.(overheated) Refractory damage.............................. Replace refractory.

Sooted heater....................................... Determine cause of sooting and correct.

Combustion fan not running Fan relay.............................................. Replace fan relay.Fan........................................................ Loose connection or failed motor.Burned motor ...................................... Incorrect wiring, replace blower.Air pressure switch............................... Replace air switch.

SECTION 5 - TROUBLESHOOTING

* Indicates symptom which usually occurs on initial start-up.

Page 44: Pool Heater

44

ELECTRICAL - STANDING PILOT MILLIVOLTPOOL OR SPA HEATER

ELECTRICAL CHECK WITH MILLIVOLT GAS VALVECAUTION: For qualified service personnel only.1. Filter must be on with adequate water flow through heater.2. Gas valve must be in "ON" position. Thermostat set higher than pool water temperature.3. Jumpers are for temporary check only. If left in place, they could cause the heater to burn up.

If pilot burner remains lit

Jump across pressureswitch terminals

If main burner does notfire, remove jumper

Check for adequate waterflow from filter

Replace pressure switch

Jump across thermostat

If main burner fires,remove jumper

If main burner doesNOT fire...

Jump across eachhigh limit and remove

jumperReplace thermostat

Replace high limit thatcaused heater to fire

Jump across both "TH"wires on gas valves

Check gas supply, gasline size, gas pressure.Also check for insects

or debris in pilot output

If pilot burnerdoes not light

Light pilot

If pilot burner goes outwhen main burner lightsor when gas valve knob

is released

If burner does not remainlit, attach millivolt meterand read pilot output

If below 500mV, check gas pressure. Also check

for insects or debris in the pilot burner

If main burner fires,remove jumper

Replacegasvalve

If main burner does notfire, remove jumper

Remove both "TH"wires from gas valve.

Relight pilot

If pilot burner stays on

Problem is a wire orcomponent short tocabinet or low gas

pressure

If above 500mV,replace gas valveClean filter

If main burner fires,remove jumper

If output is still low,replace pilot generator

Raw Output (700mV± 100)Pilot generator disconnected from valve (knobmust be held down to keep pilot on).White – NegativeRed + PositivePilot Load (500mV± 100)Pilot generator connected to valve-Powerapplied to pilot solenoid.TP(Thermopile-Robertshaw)PP(Power Pile-Honeywell)TH TP – CommonTH PP – Common

Main Valve Load (200mV± 100)Control/Limit circuit closed (All switches "ON")TP(Thermopile-Robertshaw)PP(Power Pile-Honeywell)TH TP – CommonTH PP – Common

1

2

3

Page 45: Pool Heater

45

STARTTURN GAS SUPPLY OFF.

TURN THERMOSTAT(CONTROLLER) TO CALL

FOR HEATPOWER TO PC BOARD?

(24 V NOMINAL)YES

SPARK ACROSSIGNITER/SENSOR GAP?

YES

TURN GAS SUPPLY ONPILOT BURNER LIGHTS?

YES

MAIN BURNER LIGHTS?YES

SYSTEM RUNS UNTILCALL FOR HEAT ENDS?

YES

CALL FOR HEAT ENDSSYSTEM SHUTS OFF?

YES

TROUBLESHOOTINGENDS

NOTE: Before troubleshooting, familiarize yourself with the start-up and check-outprocedure.

Check line voltage power, low voltage transformer, limit controller, thermostat(controller) and wiring.

Pull ignition lead and check spark at PC board.Spark Okay?YES NO

• Check ignition cable, ground wiring, ceramic insulator and gap, and correct.• Check boot of the ignition cable for signs of melting or buckling. Take protective

action to shield cable and boot from excessive temperatures.

• Check that all manual gas valves are open, supply tubing and pressures aregood, and pilot burner orifice is not blocked.

• Check electrical connections between PC board and pilot operator on gas control.• Check for 24 VAC across PV-MV/PV terminals on PC board. If voltage is okay,

replace gas control; if not, replace PC board.NOTE: If PC board goes into lockout, reset system. Lockout is used on L.P.G.models.

• Check for 24 VAC across MV-MV/PV terminals. If no voltage, replace module.• Check electrical connections between PC board and gas control. If okay, replace

gas valve or gas control operator, i.e. pilot gas valve, flow switch etc.

NOTE: IF PC board goes into lockout, reset system.

• Check continuity of ignition cable and ground wire.

NOTE: If ground is poor or erratic, shutdowns may occur occasionally even thoughoperation is normal at the time of checkout.

• Check that pilot flame covers flame rod and is steady and blue.• If checks are okay, replace PC board.

• Check for proper thermostat (controller) operation.• Remove MV lead at module; if valve closes, recheck temperature controller and

wiring; if not, replace gas valve.

ELECTRICAL - ELECTRONIC IGNITION IID

WARNING HIGH VOLTAGEFor qualified technicians ONLY

NOTE: Some heaters may be equipped with an ignition module that shuts off pilotgas if pilot fails to light. To reset, interrupt power to heater.

NO

NO

NO

NO

NO

NO

Replace the PC board.

Page 46: Pool Heater

46

Power On

Is the watertemperature displayed? NO

YES

Push MODEswitch to select"Pool" or "SPA"

Push Temparrow to scroll to

desired temperature

NOWater temperatureand set

temperaturedisplayed?

YES

CFH(call for heat) will

display briefly

NO

NO

YES

YES

Flame icon displayedand flashing?

(pilot lit and rectified)

Heater Fired?

END

• Check On/Off switch (under lid on control panel)• Check for 120/240 volts to the transformer (time clock, circuit breaker, wire connections)• Check for 24 volts to Circuit Board (P6 connector)

REM and Water Temperaturedisplayed and flashing

(a remote control is controlling the heater)Note: Disconnect the remote by turning the

remote function off. See page 35 for instructions.

NO

YES

Is SERVICE displayed and flashing?

Diagnostic Readouts"SNS" - Temperature sensor out of range (replace sensor)

Verify power at MV on P-4 Terminal on digital circuit board.Verify power to valve MV voltage. (Replace valve.)

SPK

Sensor FailureInspect thermister, wires, and connector at Terminal P1Check resistance value of the thermister. Reference to chart below.Replace thermister if not within 10% of values shown below.If okay, replace Circuit Board.

Temp Degrees F 40 50 60 70 80 90 100 106Resistance (k) 261.1 199.0 153.1 118.8 93.0 73.3 58.3 51.0

If okay, replace Circuit Board

Sensor resistance at various temperatures

PRS Pressure switch. Verify water flow and pressureCLEAN FILTER / STRAINER - backwash if neccessary.

HL1 High limit switch. Verify water flow. Inspect internal HL2 Thermostat (Unitherm Governor) and bypass valve.ROL Rollout Sensor - Check for blocked heat exchanger and soot.

Atmospheric Units - Replace fusible link.Low NOx Units - Press manual reset button.

CLK Fireman or Remote switch connected to safety loop is in theOFF mode.

VNT Vent switch open. Check connections to the board.If extractor installed, troubleshoot extractor.

IGN Ignition control failure. Check power at PV.PLT Pilot failure. Check spark (bad ignition circuit or hi-tension wire).

Verify gas to the heater. Verify valve operation (gas present attube fitting). Verify clean pilot orifice and clearance from igniter to ground hood. If pilot is lit, verify that the flame isrectified (the spark will be off)

DIGITAL CONTROL LOGIC - FLOW CHART

Page 47: Pool Heater

47

SECTION 6 - REPLACEMENT PARTSNOTE: To supply you with the correct part, it is impor-tant that you supply the heater model number, serialnumber and type of gas when applicable.

Any part returned for replacement under standardcompany warranties must be properly tagged with areturn parts tag, completely filled in with the heaterserial number, model number, etc., and shipped to theCompany freight prepaid.

If determined defective by the Company and withinwarranty, a like part or equal substitution will bereturned, freight collect. Credit will not be issued.

MANUFACTURER:

2151 EASTMAN AVENUEOXNARD, CA 93030

Page 48: Pool Heater

48

10-M

14-M

9-M 9-M5-C

4-C

11-S

4-S

5-S

3-B4-B5-B

1-B

6-S

7-S

4-S2-R

1-R

1-J

16-M

3-R

2-V

4-V1-V

3-V

1-S

13-S

2-S

12-S4-HP

5-HP

7-HP

6-HP

6-HP

3-HP

12-HM

17-HM

14-M

8-S

2-J 2-B

1-G

4-M2-M

5-M

12-M

11-M

13-M

3-S

10-S

16-M

7-HP

ATMOSPHERIC HEATERS

Page 49: Pool Heater

49

LOW NOx HEATERS

Page 50: Pool Heater

50

16-HM

15-HM

12-HM

9-HM

10-HM

2-C

3-M

11-HM8-HM

(OPTIONAL)

POLYMER IN/OUT HEADER AND ACCESSORIES

1-M

3-C

6-C

5-HM

17-HM

14-HM

13-HM

2-HM

4-HM7-HM

3-HM

6-HM

2-S

9-S

4-S

HONEYWELL IID ATMOSPHERIC PILOT

2-P

7-P9-P

8-P

1-P

5-P

6-P

3-P

9-P

HONEYWELL MILLIVOLT PILOT

1-P

2-P

4-P

IID LOW NOx PILOT

6-P

Page 51: Pool Heater

51

CALLA604A633A662A602NOITPIRCSEDTUO

B BURNER TRAY F493010F393010F293010F193010*)levelaes(srenruB/wyarTrenruBB-1F893010F793010F693010F593010*)levelaes(srenruBo/wyarTrenruBF204010F104010F004010F993010tlovilliMtaNevlaVsaG/wyarTrenruBF604010F504010F404010F304010tlovilliMorPevlaVsaG/wyarTrenruBF014010F904010F804010F704010DIItaNevlaVsaG/wyarTrenruBF414010F314010F214010F114010DIIorPevlaVsaG/wyarTrenruBF814010F714010F614010F514010tiKnwoDdloH/recapSrenruBB-272/01210322/01210381/01210331/012103renruBB-372/F97005322/F97005381/F97005331/F970053*)leveLaeS(05#.taNecifirOrenruBB-472/F38005322/F38005381/F38005331/F380053*)leveLaeS(75#.orPecifirOrenruB

F424010F324010F224010F124010srenrubo/wdlofinaMo/wyarTrenruBB-5C CONTROLS

1-C Thermostat Auto Reset 135 Deg Surface Mount 006725F 006725F 006725F 006725F2-C AGS 135° (Auto Gas Shut-Off) - Red Epoxy 600892B 600892B 600892B 600892B

B398006B398006B398006B398006yxopEkcalB-°041timiLhgiHC-3F352010F352010F352010F352010stinUDIIlortnoC/draoB.C.PC-4

5-C Thermostat Control MV Units Mechanical 003346F 003346F 003346F 003346FF775900F775900F775900F775900stinUDIIrosneSerutarepmeTC-6

G GAS VALVEF898300F898300F898300F898300VM.taN-evlaVnoitanibmoCG-1F998300F998300F998300F998300VM.orP-evlaVnoitanibmoCF009300F009300F009300F009300DII.taN-evlaVnoitanibmoCF603400F603400F603400F603400DII.orP-evlaVnoitanibmoC

HP HEAT EXCHANGER - POLYMERF640010F540010F440010F340010reppoCyssAegnahcxEtaeHPH-1F953010F853010F753010F653010lekciNorpuCyssAegnahcxEtaeHF728600F728600F728600F728600etelpmoCredaeHteltuO/telnIPH-2F607600F607600F607600F607600)PH-6sedulcnI(redaeHteltuO/telnIF707600F707600F707600F707600)PH-6sedulcnI(redaeHnruteRPH-3F260010F160010F060010F950010**reppoCeldnuBebuTPH-4F763010F663010F563010F463010**lekciNorpuCeldnuBebuTF140010F040010F162500F830010elffaBPH-5F952800F952800F952800F952800tiKtuNegnalFPH-6F317600F317600F317600F317600)2(teksaGgniROPH-7F417600F417600F417600F417600cinortcelElatigiDretpadArosneSPH-8F508600F508600F508600F508600tlovilliMlleWrosneSF517600F517600F517600F517600tiKssapyBPH-9F617600F617600F617600F617600evlaVssapyBPH-01F717600F717600F717600F717600tfahS/maDssapyBPH-11F817600F817600F817600F817600)dedulcnIseziSllA(gnirpSssapyBPH-21F917600F917600F917600F917600ronrevoGmrehtinUPH-31F027600F027600F027600F027600gulPronrevoGmrehtinUPH-41F127600F127600F127600F127600gulPniarDPH-51

16-HP Inlet/Outlet Header Dam N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP

F327600F327600F327600F327600)2(tuN&rotcennoCCVP"2PH-71F427600F427600F427600F427600)2(gniROPH-81

19-HP Inlet/Outlet Header Baffle w/Header Dam 006826F 006826F 006826F 006826F

*FOR INSTALLATION AT OVER 2,000 FEET ABOVE SEA LEVEL, DERATE 4% PER I,000 FEET ABOVE SEA LEVEL.**WARNING: The Hydraulic conditions or water chemistry that caused the tube bundle to fail have very likely alsodamaged the bypass valve and Unitherm Governor. We recommend you replace the Unitherm Governor andinspect the bypass assembly. Failure to do so could cause premature failure of this replacement part.

ATMOSPHERIC HEATERS

Page 52: Pool Heater

52

CALLA604A633A662A602NOITPIRCSEDTUO

HM HEAT EXCHANGER - METALF450010F350010F727600F150010ICEMSAreppoC.yssAegnahcxEtaeHMH-1

Heat Exchange Assy.Cupro Nickel ASME CI 010360F 010361F 010362F 010363FF037600F037600F037600F037600etelpmoCICEMSAredaeHteltuO/telnIMH-2F913210F913210F913210F913210ICEMSAredaeHteltuO/telnIF667300F667300F667300F667300egnalFteltuO&telnIMH-51B632260B632260B632260B632260snoitcennoC"2/11teksaGegnalFMH-61B080008B080008B080008B080008snoitcennoC"2teksaGegnalFF137600F137600F137600F137600ICEMSAredaeHnruteRMH-3F850010F750010F337600F550010*EMSAreppoCeldnuBebuTMH-4F173010F073010F963010F863010*EMSAlekciNorpuCeldnuBebuTF140010F040010F162500F830010elffaBMH-5F078700F078700F078700F078700tiKtloBdutSMH-6B410008B410008B410008B410008)9(teksaGredaeHMH-7B432260B432260B432260B432260ronrevoGmrehtinUMH-8452058452058452058452058gnirpSreniateR.G.UMH-9B532260B532260B532260B532260evlaVssapyBMH-01352058352058352058252058gnirpSssapyBMH-11917005917005917005917005evlaVniarDMH-21F567300F567300F567300F567300lleWrosneSMH-31302003302003302003302003pilCgniniateRlleWMH-41F462500F462500F462500F462500revoC&gulPniarDraeRMH-71

J CONTROL BOXF637600F637600F637600F637600V42/042/021remrofsnarTJ-1F394900F394900F394900F394900hctiwSrekcoRJ-2

M MISCELLANEOUS COMPONENTSF737600F737600F737600F737600ISP57.1hctiwSerusserPM-1

Pressure Switch 11 PSI Special-See Water Pressure Switch Adj. 009133F 009133F 009133F 009133FF994900F994900F994900F994900bonKtatsomrehTM-2703008703008703008703008VMtfahStatsomrehTM-3F688600F688600F688600F688600potsbonKM-4F998500F998500F998500F998500esuFlamrehTM-5F422700F422700F422700F190800)lanoitpO(ISP521VRPM-6F178250F178250F178250F178250tiKgnimileDM-7F683010F683010F683010F683010tlovilliMssenraH/eriWM-8F094900F094900F094900F094900DIIssenraH/eriWF984900F984900F984900F984900)laceDlaiDsedulcnI(VMlezeBlortnoCM-9F858900F858900F858900F858900VMlaceDlaiDM-01F194900F194900F194900F194900)laceDhctiwSsedulcnI(DIIlezeBlortnoCM-11F294900F294900F294900F294900enarbmeM-laceD/hctiwSM-21F784900F784900F784900F784900revoClezeBlortnoCM-31

14-M Gasket Insulation (Swaybrace & Jacket Top) 010350F 010350F 010350F 010350F521057521057521057521057)neerG(tniaPpu-hcuoTM-51621057621057621057621057)yarGkraD(tniaPpu-hcuoT636110636110636110636110)lanoitpO(tekcarBnwoDeiTM-61110210110210110210110210)ylnOEMSA(nO/ddAedoCsaxeTM-71

P PILOTB525006B525006B525006B525006VM.taNtoliPP-1B575006B575006B575006B575006VM.orPtoliP

2-P Pilot Nat & Pro IID 002003F 002003F 002003F 002003FF109300F109300F109300F109300VM.taNecifirOtoliPP-3F209300F209300F209300F209300VM.orPecifirOtoliPF309300F309300F309300F309300020.DII.taNecifirOtoliPP-4F803400F803400F803400F803400210.DII.orPecifirOtoliPB910006B910006B910006B910006VMrotareneGtoliPP-5F253010F253010F253010F253010VMtekcarBGTMtoliPP-6296603296603296603296603DIItekcarBgnitnuoMtoliPP-7699260699260699260699260)ylnOstinUVM(ebuTrethgiLP-8F870400F870400F870400F870400ebuTtoliPP-9F468700F468700F468700F468700edortcelEtoliPhtiwDIIeriWnoisneTiHP-01F153010F153010F153010F153010dleihStoliPP-11

R REFRACTORYF880010F880010F880010F880010tR&tLnommoCyrotcarfeRR-1F290010F190010F090010F980010)raeR&tnorF(nommocnUyrotcarfeRR-2F093010F983010F883010F783010tiKreniateRyrotcarfeRR-3

*WARNING: The Hydraulic conditions or water chemistry that caused the tube bundle to fail have very likely alsodamaged the bypass valve and Unitherm Governor. We recommend you replace the Unitherm Governor andinspect the bypass assembly. Failure to do so could cause premature failure of this replacement part.

ATMOSPHERIC HEATERS

Page 53: Pool Heater

53

CALLA604A633A662A602NOITPIRCSEDTUO

S SHEETMETALF050010F940010F840010F740010)derevuoL(poTtekcaJS-1

2-S Flue Collector (Units with Polymer Header) 010071F 010072F 010073F 010074FF870010F770010F670010F570010)redaeHlateMhtiwstinU(rotcelloCeulF

3-S Door Assy.F183010F083010F973010F873010kapyaRF583010F483010F383010F283010meehR

4-S Access Panel Set (3 Pcs Units with Polymer Header) 010311F 010311F 010311F 010311FAccess Panel Set (3 Pcs. Units with Metal Header) 010312F 010312F 010312F 010312F

F673010F673010F673010F673010thgiRlenaPediStekcaJS-5F773010F773010F773010F773010tfeLlenaPediStekcaJS-6F573010F473010F373010F273010).scP2(lenaPraeRtekcaJS-7505900505900505900505900kcoL/revoCtatslooPS-8F913010F913010F913010F913010revoCtimiLhgiHS-9F023010F023010F023010F023010dleihStaeHesaBS-01F423010F323010F223010F123010lenaPlortnoCtnorFpUS-11F243010F243010F243010F243010dleihStimiLhgiHS-21F823010F723010F623010F523010dleihSrehtaeWS-31

V VENTING1-V Indoor Stack Kit (Includes inner adapter panel) 009838 009839 009840 009841

Outdoor Stack Kit (Includes inner adapter panel) 009834 009835 009836 009837F333010F233010F133010F033010retpadAkcatSV-2F464110F364110F264110F164110retpadAkcatSretuOV-4733010633010533010433010poT"adogaP"V-3

A604A633A662A602*STIKNOISREVNOCcirehpsomtAGas Conversions

B296400B296400B096400B096400toliPVM.orPot.taNF024010F024010F914010F914010toliPVM.taNot.orP

********toliPDII.orPot.taN********toliPDII.taNot.orP

** Conversion must be made with complete burner tray and gas valve (see item 1-B).* Gas conversions are to be done only by a qualified agency.

ATMOSPHERIC HEATERS

Page 54: Pool Heater

54

CALLA704A733A762A702NOITPIRCSEDTUO

BB BURNER TRAY***F643010F543010F443010F343010)0005-0(srenruB/wyarTrenruBB-1F780010F680010F580010F480010)0005-0(renruBo/wyarTrenruBF752010F652010F552010F452010tiKnwoDdloHrenruBB-26/2370135/2370134/2370133/237013renruBB-36/2361535/2361534/2361533/236153*)0005-0(62#.taNecifirOrenruBB-46/3251535/3251534/3251533/325153*).tf0005evoba(13#.taNecifirOrenruBF240010F240010F240010F240010rewolBB-5F178010F178010F178010F178010naFgnilooCB-7F143010F043010F933010F833010etalPecifirOriAnoitsubmoCB-6

C CONTROLS1-C Thermostat Auto Reset 135 Deg Surface Mount 006725F 006725F 006725F 006725F2-C AGS 135° (Auto Gas Shut-Off) - Red Epoxy 600892B 600892B 600892B 600892B

B398006B398006B398006B398006yxopEkcalB-°041timiLhgiHC-3F352010F352010F352010F352010lortnoC/draoB.C.PC-4F775900F775900F775900F775900rosneSerutarepmeTC-6F553010F453010F531800F260800hctiwSerusserPrewolBC-7

G GAS VALVEF923010F923010F923010F923010taN-ffO/nOsaG-evlaVnoitanibmoCG-1

HP HEAT EXCHANGER - POLYMERF640010F540010F440010F340010reppoCyssAegnahcxEtaeHPH-1F953010F853010F753010F653010lekciNorpuCyssAegnahcxEtaeHF728600F728600F728600F728600etelpmoCredaeHteltuO/telnIPH-2F607600F607600F607600F607600)PH-6sedulcnI(redaeHteltuO/telnIF707600F707600F707600F707600)PH-6sedulcnI(redaeHnruteRPH-3F260010F160010F060010F950010**reppoCeldnuBebuTPH-4F763010F663010F563010F463010**lekciNorpuCeldnuBebuTF140010F040010F162500F830010elffaBPH-5F952800F952800F952800F952800tiKtuNegnalFPH-6F317600F317600F317600F317600)2(teksaGgniROPH-7F417600F417600F417600F417600cinortcelElatigiDretpadArosneSPH-8F508600F508600F508600F508600tlovilliMlleWrosneSF517600F517600F517600F517600tiKssapyBPH-9F617600F617600F617600F617600evlaVssapyBPH-01F717600F717600F717600F717600tfahS/maDssapyBPH-11F817600F817600F817600F817600)dedulcnIseziSllA(gnirpSssapyBPH-21F917600F917600F917600F917600ronrevoGmrehtinUPH-31F027600F027600F027600F027600gulPronrevoGmrehtinUPH-41F127600F127600F127600F127600gulPniarDPH-51

16-HP Inlet/Outlet Header Dam N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP

F327600F327600F327600F327600)2(tuN&rotcennoCCVP"2PH-71F427600F427600F427600F427600)2(gniROPH-81F628600F628600F628600F628600maDredaeH/welffaBredaeHteltuO/telnIPH-91

HM HEAT EXCHANGER - METALF450010F350010F727600F150010ICEMSAreppoC.yssAegnahcxEtaeHMH-1

Heat Exchange Assy.Cupro Nickel ASME CI 010360F 010361F 010362F 010363FF037600F037600F037600F037600)etelpmoC(ICEMSAredaeHteltuO/telnIMH-2F913210F913210F913210F913210ICEMSAredaeHteltuO/telnIF667300F667300F667300F667300egnalFteltuO&telnIMH-51B632260B632260B632260B632260snoitcennoC"2/11teksaGegnalFMH-61B080008B080008B080008B080008snoitcennoC"2teksaGegnalFF137600F137600F137600F137600ICEMSAredaeHnruteRMH-3F850010F750010F337600F550010**EMSAreppoCeldnuBebuTMH-4F173010F073010F963010F863010**EMSAlekciNorpuCeldnuBebuTF140010F040010F162500F830010elffaBMH-5F078700F078700F078700F078700tiKtloBdutSMH-6B410008B410008B410008B410008)9(teksaGredaeHMH-7B432260B432260B432260B432260ronrevoGmrehtinUMH-8452058452058452058452058gnirpSreniateR.G.UMH-9B532260B532260B532260B532260evlaVssapyBMH-01352058352058352058252058gnirpSssapyBMH-11917005917005917005917005evlaVniarDMH-21F567300F567300F567300F567300lleWrosneSMH-31302003302003302003302003pilCgniniateRlleWMH-41F462500F462500F462500F462500revoC&gulPniarDraeRMH-71

*FOR INSTALLATIONS AT OVER 5,000 FEET ABOVE SEA LEVEL, CONSULT THE FACTORY**WARNING: The Hydraulic conditions or water chemistry that caused the tube bundle to fail have very likely alsodamaged the bypass valve and Unitherm Governor. We recommend you replace the Unitherm Governor andinspect the bypass assembly. Failure to do so could cause premature failure of this replacement part.***Replacement burner trays are built for sea level, natural gas applications unless otherwise specified at the time the orderis placed.

LOW NOx HEATERS

Page 55: Pool Heater

55

CALLA704A733A762A702NOITPIRCSEDTUO

J CONTROL BOXF637600F637600F637600F637600V42/042/021remrofsnarTJ-1F394900F394900F394900F394900hctiwSrekcoRJ-2F487800F487800F487800F487800xoNwoLyaleRJ-3

M MISCELLANEOUS COMPONENTSF737600F737600F737600F737600ISP57.1hctiwSerusserPM-1

Pressure Switch 11 PSI Special-See Water Pressure Switch Adj. 009133F 009133F 009133F 009133FF530600F530600F530600F530600Fº003hctiwStuO-lloRM-2F422700F422700F422700F190800)lanoitpO(ISP521VRPM-3F178250F178250F178250F178250tiKgnimileDM-4F743010F743010F743010F743010ssenraH/eriWM-5F194900F194900F194900F194900)laceDhctiwSsedulcnI(lezeBlortnoCM-6F294900F294900F294900F294900enarbmeM-laceD/hctiwSM-7F784900F784900F784900F784900revoClezeBlortnoCM-8

9-M Gasket Insulation (Swaybrace & Jacket Top) 010350F 010350F 010350F 010350FF843010F843010F843010F843010ebuTelpmaShctiwSerusserPriA/rewolBM-01521057521057521057521057)neerG(tniaPpu-hcuoTM-11621057621057621057621057)yarGkraD(tniaPpu-hcuoT636110636110636110636110)lanoitpO(tekcarBnwoDeiTM-21F547110F547110F547110F547110)lanoitpO(Fº052hctiwStuO-lloRM-31F337110F337110F337110F337110)edargpU(Fº052hctiwStuO-lloR110210110210110210110210)ylnOEMSA(nO/ddAedoCsaxeTM-41

P PILOTF232010F232010F232010F232010xoNwoLDII.taNtoliPP-1

A/NA/NA/NA/NedortcelEtoliPP-2F632010F532010F432010F332010tekcarBgnitnuoMtoliPP-3F629110F629110F629110F629110ebuTtoliPP-4F943010F943010F943010F943010DIIeriWnoisneTiHP-5F729110F729110F729110F729110)cirteM(tuNretpadAP-6

R REFRACTORYF970010F970010F970010F970010)thgiR&tfeL(nommoCyrotcarfeRR-1F380010F280010F180010F080010)raeRdnatnorF(nommocnUyrotcarfeRR-2F562010F462010F362010F262010tiKreniateRyrotcarfeRR-3

S SHEETMETALF050010F940010F840010F740010)derevuoL(poTtekcaJS-1F660010F560010F460010F360010)redaeHremyloPhtiwstinU(rotcelloCeulFS-2F070010F960010F860010F760010)redaeHlateMhtiwstinU(rotcelloCeulF

3-S Door Assy.F072010F962010F862010F762010kapyaRF472010F372010F272010F172010meehR

4-S Access Panel Set (3 Pcs. Units with Polymer Header) 010311F 010311F 010311F 010311FAccess Panel Set (3 Pcs. Units with Metal Header) 010312F 010312F 010312F 010312F

F313010F313010F313010F313010thgiRlenaPediStekcaJS-5F413010F413010F413010F413010tfeLlenaPediStekcaJS-6F813010F713010F613010F513010).scP2(lenaPraeRtekcaJS-7505900505900505900505900kcoL/revoCtatslooPS-8F913010F913010F913010F913010revoCtimiLhgiHS-9F023010F023010F023010F023010dleihStaeHesaBS-01F423010F323010F223010F123010lenaPlortnoCtnorFpUS-11F243010F243010F243010F243010dleihStimiLhgiHS-21F823010F723010F623010F523010dleihSrehtaeWS-31

V VENTING1-V Indoor Stack Kit (Includes inner adapter panel) 009838 009839 009840 009841

Outdoor Stack Kit (Includes inner adapter panel) 009834 009835 009836 009837F333010F233010F133010F033010retpadAkcatSV-2F464110F364110F264110F164110retpadAkcatSretuOV-4733010633010533010433010poT"adogaP"V-3

LOW NOx HEATERS

Page 56: Pool Heater