Pioneer Deh 3100r Deh 3130r

PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 1999 K-ZZD. OCT. 1999 Printed in Japan

ORDER NO.

CRT2418

HIGH POWER CD PLAYER WITH RDS TUNER

DEH-3130R X1N/EW

ServiceManual

CONTENTS1. SAFETY INFORMATION ............................................2

2. EXPLODED VIEWS AND PARTS LIST .......................3

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...10

4. PCB CONNECTION DIAGRAM ................................28

5. ELECTRICAL PARTS LIST ........................................38

6. ADJUSTMENT..........................................................44

7. GENERAL INFORMATION .......................................48

7.1 DIAGNOSIS ........................................................48

7.1.1 TEST MODE..............................................48

7.1.2 DISASSEMBLY .........................................52

7.2 PARTS .................................................................56

7.2.1 IC................................................................56

7.2.2 DISPLAY....................................................63

8. OPERATIONS AND SPECIFICATIONS.....................64

DEH-3100R-B X1N/EW

DEH-3130R/X1N/EW

- This service manual should be used together with the following manual(s):Model No. Order No. Mech. Module Remarks

CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly

DEH-3100R X1N/EW

2DEH-3130R,3100R-B,3100R

- CD Player Service Precautions1. For pickup unit(CXX1285) handling, please refer

to"Disassembly"(see page 52).

During replacement, handling precautions shall be

taken to prevent an electrostatic discharge(protection

by a short pin).

2. During disassembly, be sure to turn the power off

since an internal IC might be destroyed when a con-

nector is plugged or unplugged.

3. Please checking the grating after changing the ser-

vice pickup unit(see page 44).

1. SAFETY INFORMATIONThis service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do soand refer the repair to a qualified service technician.

1. Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable

results.

Caution: 1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.2. During repair or tests, do not view laser beam for 10 seconds or longer.

2. A CLASS 1 LASER PRODUCT label is affixed to thebottom of the player.

3. The triangular label is attached to the mechanismunit frame.

4. Specifications of Laser Diode

Specifications of laser radiation fields to which human access is possible during service.Wavelength = 800 nanometers

CLASS 1LASER PRODUCT

3DEH-3130R,3100R-B,3100R

2. EXPLODED VIEWS AND PARTS LIST2.1 PACKING

11

8

9

5

4

6

3

2

7

12

13

10

1

1 Cord Assy CDE6238* 2 Accessory Assy CEA2397

3 Screw CBA10024 Handle CNC53955 Bush CNV3930

* 6 Polyethylene Bag E36-6157 Polyethylene Bag CEG-162

8-1 Owners Manual CRD30738-2 Owners Manual CRD30748-3 Owners Manual CRD3075

8-4 Installation Manual CRD3076* 8-5 Passport CRY1013* 8-6 Warranty Card CRY1157

8-7 Polyethylene Bag CEG11169 Case Assy CXB3520

10 Carton See Contrast table(2)11 Contain Box See Contrast table(2)12 Protector CHP225113 Protector CHP2252

Mark No. Description Part No. Mark No. Description Part No.

(1) PACKING SECTION PARTS LIST

NOTE:

- Parts marked by * are generally unavailable because they are not in our Master Spare Parts List.

- Screws adjacent to mark on the product are used for disassembly.

4DEH-3130R,3100R-B,3100R

- Owner's Manual, Installation ManualModel Part No. LanguageDEH-3130R/X1N/EW CRD3073 English, SpanishDEH-3100R-B/X1N/EW CRD3074 German, FrenchDEH-3100R/X1N/EW CRD3075 Italian, Dutch

CRD3076 English, Spanish, German, French, Italian, Dutch

Part No.Mark No. Symbol and Description DEH-3130R/X1N/EW DEH-3100R-B/X1N/EW DEH-3100R/X1N/EW

10 Carton CHG3882 CHG3883 CHG388111 Contain Box CHL3882 CHL3883 CHL3881

(2) CONTRAST TABLE

DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except

for the following:

5DEH-3130R,3100R-B,3100R

2.2 EXTERIOR

6DEH-3130R,3100R-B,3100R

1 Screw BMZ26P120FMC2 Screw BSZ26P060FMC3 Screw BSZ30P060FMC4 Screw BSZ30P120FMC5

6 IC(IC551) PAL005A7 Cable CDE61608 Cord Assy CDE62389 Resistor RS1/2PMF102J

10 Transistor(Q981,991) 2SD2396

11 Cap CNS147212 Fuse(10A) CEK113613 Holder CNC679814 Cover CNC836715 Spacer CNM4913

16 Earth Plate CNC836817 Insulator CNM600618 Insulator CNM622419 20

21 Tuner Amp Unit CWM684122 Screw ASZ26P080FMC23 Screw BPZ26P080FMC24 Screw BSZ26P160FMC25 Connector(CN551) CDE5996

26 Antenna Cable(CN502) CDH125427 Pin Jack(CN431) CKB102828 Terminal(CN501) CKF105929 Connector(CN951) CKM1299

* 30 Connector(CN681) CKS2227

31 32 Connector(CN651) CKS358133 34 Holder CNC753335 Holder CNC8130

36 Holder CNC804137 Holder CNC804338 Insulator CNM596739 Heat Sink CNR150640 FM/AM Tuner Unit CWE1500

41 Holder CNC753242 Chassis Unit See Contrast table(2)43 44 Button CAC483645 Spring CBH1835

46 Spring CBH236747 Spring CBH220848 Bracket CNC679149 Holder CNC804250 Cover CNM6276

51 Panel See Contrast table(2)52 Arm CNV469253 Arm CNV472854 Arm CNV557655 Screw IMS20P030FZK

56 Case Unit CXB403357 58 59 60

61 Detach Grille Assy See Contrast table(2)62 Screw BPZ20P100FZK63 Button(DETACH) See Contrast table(2)64 Button(1-6) CAC623965 Button(SOURCE) CAC6241

66 Button(+) See Contrast table(2)67 Button(-) See Contrast table(2)68 Button(F) See Contrast table(2)69 Button(A) See Contrast table(2)70 Button(EQ) CAC6247

71 Button(EJECT) CAC624872 Button(BAND) See Contrast table(2)73 Spring CBH221074 Cover See Contrast table(2)75 Lighting Conductor CNV5909

76 Lighting Conductor CNV591077 Housing CNV591878 Keyboard Unit See Contrast table(2)79 LCD See Contrast table(2)80 Connector(CN1801) CKS3580

81 Holder CNC846882 Sheet CNM643583 Lighting Conductor CNV590884 Connector CNV605185 Grille Sub Assy See Contrast table(2)

86 CD Mechanism Module(S8.1) CXK520187 Screw ISS26P055FUC

(1) EXTERIOR SECTION PARTS LIST


7DEH-3130R,3100R-B,3100R

Part No.Mark No. Symbol and Description DEH-3130R/X1N/EW DEH-3100R-B/X1N/EW DEH-3100R/X1N/EW

42 Chassis Unit CXB4711 CXB4709 CXB471051 Panel CNS5340 CNS5188 CNS518861 Detach Grille Assy CXB4722 CXB4723 CXB472163 Button(DETACH) CAC5929 CAC5789 CAC578966 Button(+) CAC6559 CAC6242 CAC6242

67 Button(-) CAC6560 CAC6243 CAC624368 Button(F) CAC6561 CAC6244 CAC624469 Button(A) CAC6562 CAC6245 CAC624572 Button(BAND) CAC6578 CAC6249 CAC624974 Cover CAC5794 CNS5622 CNS5622

78 Keyboard Unit CWM6796 CWM6797 CWM679579 LCD CAW1570 CAW1572 CAW157085 Grille Sub Assy CXB5251 CXB5252 CXB5250

(2) CONTRAST TABLE

DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except

for the following:

8DEH-3130R,3100R-B,3100R

2.3 CD MECHANISM MODULE

9DEH-3130R,3100R-B,3100R


1 Control Unit CWX24112 Connector(CN802) CKS21923 Connector(CN801) CKS21934 Connector(CN701) CKS27735 Connector(CN101) CKS3486

6 Screw BMZ20P030FMC7 Screw BSZ20P040FMC8 Screw(M2x3) CBA10779 Screw(M2x5) EBA1028

10 Screw CBA1243

11 Screw(M2x4) CBA136212 Washer CBF103713 Washer CBF103814 Washer CBF106015

16 Spring CBH207917 Spring CBH211718 Spring CBH231419 Spring CBH211020 Spring CBH2282

21 Spring CBH231822 23 Spring CBH232424 Spring CBH211825 Spring CBH2161

26 Spring CBH216327 Spring CBH218928 Spring CBH224929 Spring CBH226030 Spring CBH2262

31 Bracket CNC856832 Spring CBL136933 Connector CDE553134 Connector CDE553235 Shaft CLA3304

36 Screw(M2.6x6) CBA145837 Frame CNC856538 Frame CNC874939 Lever CNC754640 Arm CNC8663

41 Bracket CNC856742 43 Spacer CNM331544 Sheet CNM665945

46 47 Ball CNR118948 Belt CNT108649 Roller CNV450950 Arm CNV6037

51 Arm CNV524752 Arm CNV524853 Arm CNV524954 Guide CNV525455 Guide CNV5255

56 Gear CNV525757 Gear CNV525658 Guide CNV617659 Damper CNV601060 Arm CNV6096

61 Arm CNV603162 Arm CNV621163 Guide CNV601264 Guide CNV551065

66 Guide CNV575167 Clamper CNV601368 Gear CNV581369 Motor Unit(M1) CXB219070 Screw Unit CXB4726

71 Chassis Unit CXB479772 Gear Unit CXB472873 Arm Unit CXB575374 Motor Unit(M2) CXB219575 Lever Unit CXB4730

76 Arm Unit CXB473177 Motor Unit(M3) CXB256278 Arm Unit CXB473279 Bracket Unit CXB479580 Screw JFZ20P025FMC

81 Screw JGZ17P025FZK82 Washer YE20FUC83 Pickup Unit(Service)(P8) CXX128584 Screw IMS26P030FMC

* 85 PCB CNX2982

86 Photo-transistor(Q1, 2) CPT230SX-TU87 Damper CNV601188 Lack CNV601489 Spring CBH2315

- CD MECHANISM MODULE SECTION PARTS LIST

10

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM3.1 BLOCK DIAGRAM

ANT1

TV

ANT2

TV

R

F TV

IC 3BR9010FVAM 2ND IF 450kHz

M

M

M

LDMD

HOLOGRAMUNIT

FOCUS ACTTRACKING ACT

LD+MD

FO+

TO+

145

4

3

PICKUP UNIT(SERVICE)(P8)

SPINDLEMOTOR

CARRIAGEMOTOR

LOADINGMOTOR

12

3

4

31

2

SELECTSENSE

DISC SENSE

E PHOTO UNIT(S8)

CN801

CN802

D803 D802 D801

VD

S802CLAMP

6

5

11

22

23

21

1

28

21

CDLOADCDEJET

CONT

EJTSNS

DSCSNS

CLAMP

CD5VON

VDCONT

VDD IC 701BA05SFP IN

+5V REGULATOR24

1

VD

Q991

Q992

B.U

ANTENNA CN5021

2

A TUNER AMP UNIT

B FM/AM TUNER UNIT

27

28

FM FRONT ENDQ3

Q201 Q204

AM RF

FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53

MIXER.IF AMP DETIC 1

PML002A

38 39 42 44 46 63

32 19

46

6

21

18LDET

COMP

34 33 41 44 11 12 1369

70

54

78

65

71

7574615755453335

22

2225 10 14 12 15 16 8 13 2 3 4

CF202

VDD

LOCL

VCC

Q401

SYS+B VDDD

I/DO

CE2

CK CE1

SDBL

SL FMSD

PCE2 CK

PCE1

SDBW S

L

SD

PDIO

NL1

NL2

EEPROM5

6

4

3

IC 2 PM4008A

FM MPX

Q524 Q542Q525 Q540

RDSDECODER

IC 701PM4009A

20

11 12

24

X501

Q701VDD

TMUTE

fm/AM

D CONTROL UNITQ101CN101

FOP

TOP

A+C/F

B+D/E

98 LD L_OUT

PD

HOME

97

24

23

39

X201

TD/FD

SD/MD

RF-AMP, DSP,SERVO, DAC

IC 201UPD63711GC

16CN701 CN681

17

1

8

24

LOUT

SP601ALARM

BUZZER

IC 301BA5985FM

S801HOME12

16

18

11

14

1310

9

SOP

TOPFOP

SOM

COPCOMLOPLOM

FWD

REV

MUTE

25 24

CD D

RIVE

R

NL1

7 18

19

20

14

3

2

4

CLAMP

DSCSNS

EJTSNS

CDLOADCDEJET

CONT

Q202

32

PDIO

11

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

SWVDD

AVCC VDD

KYDT

DPDT

KEY CONTROLLERAND

LCD DRIVER

IC 1801PD6294A

1

6

5

3

8

3

4

6

KEY MATRIX

78 23

36

88

29

76 NL1

FM/AM

ldet

tmute

SD

SL

SDBW

TUNPCE

TUNPCK

TUNPCE2

TUNPDO

LOCL

IN1_L

IN2_L

PEE

38

74

77

99

97

32

98

30

2

3

100

SYSTEMCONTROLLER

IC 601(1/2)PE5139A

VSTVCKVDT

B.UVDD

Q973B.U

BACKUP

FL

FL+

RL

RL+

B.REM

ACC

2

1

9

11

10

12

5

4

7

ELECTRONIC VOLUME/SOURCE SELECTOR

IC 451PML003AM

SYSTEMCONTROLLER

IC 601(2/2)PE5139A

ASENS92

BSENS93

DRSYS1

TELMUTE2

SYSPW3

MUTE28

DSENS52

KYDT95

DPDT96

RESET11

GRNILM20

FL10

RL11

POWER AMP

IC 551PAL005A

14

12

22 4 25

5

3

21

23

FL

MUTE STBY B.REM

RL

B.U

TELMUTE

bsens

asens

Q921

Q971Q551 MUTE

C KEYBOARD UNIT

CN1801CN651DSENS

LCD

11 13

X1901

8

9

Q982Q921B.USYS+B

SYSPW

Q652

Q653

B.U

RESETIC 631

S80735ANDZI VDD1 2

RESET

SY

SP

W

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

BACKUP

BACK UP

FL

FL+

RL

RL+

B.REM

ACC

TEL MUTE

Q431

Q434

GRN

GRN

FUSE10A

GND

CD5VON

59

58

53

78

79

64

56

54

VDCONT

CLAMP

DSCSNS

EJTSNS

CDLOAD

CDEJET

CONT

CN431

REAR L CH

TUNPDI94PDIO

B.REM

TELMUTE

12

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)Note: When ordering service parts, be sure to refer to EXPLODED VIEWS AND PARTS LIST or ELECTRICAL

PARTS LIST.

A-a A-b

A-aA-a A-b A-b

A-b A-b A-a A-a

Large sizeSCH diagram

Guide page

Detailed page

A

A-a

DS

P-2

01M

-S00

B

ANTENNACABLE

1

5

2

4

3

6

SYSTEM CONTROLLER

SOURCE SELECTOR/ELECTRONIC VOLUME

VD REGULATOR

RDS DECODER

FM : -16.5dBsAM : -27dBsS-CD : 0dBsFM(100%) : -15.5dBs

AM(30%) : -26dBs

S-CD : 4.4dBs

The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.

Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.

NOTE :

Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.

Decimal points for resistorand capacitor fixed valuesare expressed as :2.2 2R20.022 R022

A

B

ED

TUNER AMP UNIT

FM/A

M T

UN

ER

UN

IT

CD

ME

CH

AN

ISM

M

OD

ULE

13

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

AA-b

A

ER

A15

-02V

H

ERA15-02VH

ER

A15

-02V

H

ER

A15

-02V

H

ERA15-02VH

1K(1/2W)

1K(1/2W)

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

B.REM

BACKUP

POWER AMP

TELEPHONE MUTE

REARPREOUT

RESET

FM : 32dBsAM : 24dBsS-CD : 36dBs

FM : 5.84dBsAM : -2.66dBsS-CD : 9.74dBs

FM : 6.6dBsAM : -1.9dBsS-CD : 10.5dBs

ILLUMINATIONPOWER SUPPLY

6

5

1

2

34

6

5

1

2

3

4

ACC SENSE

BACK UP SENSE

8V REGULATOR

VDD REGULATOR

MUTE

>CEK1136

C KEYBOARD UNIT

14

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

1

5 2

4

36

SY

ST

EM

CO

NT

RO

LLE

R

SO

UR

CE

SE

LEC

TO

R/

ELE

CT

RO

NIC

VO

LUM

E

FM :

-16.

5dB

sA

M :

-27d

Bs

S-C

D :

0dB

sFM

(100

%)

: -15

.5d

Bs

AM

(30%

) : -

26d

Bs

A-a

A-a

A-b

AB

TU

NE

R A

MP

UN

ITFM/AM TUNER UNIT

1 2 3 4 765

15

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

DSP-201M-S00B

AN

TE

NN

AC

AB

LE

SY

ST

EM

CO

NT

RO

LLE

R

VD

RE

GU

LAT

OR

RD

S D

EC

OD

ER

S-C

D :

4.4d

Bs

Th

e >

mar

k fo

un

d o

n s

om

e co

mp

on

ent

par

ts in

dic

ates

the

imp

ort

ance

of

the

safe

ty f

acto

r o

f th

e p

art.

Th

eref

ore

, wh

en r

epla

cin

g, b

e su

re t

o u

se p

arts

of

iden

tica

l des

ign

atio

n.

Sym

bo

l in

dic

ates

a r

esis

tor.

No

dif

fere

nti

atio

n is

mad

e b

etw

een

ch

ip r

esis

tors

an

dd

iscr

ete

resi

sto

rs.

NO

TE

: Sym

bo

l in

dic

ates

a c

apac

ito

r.N

o d

iffe

ren

tiat

ion

is m

ade

bet

wee

n c

hip

cap

acit

ors

an

dd

iscr

ete

cap

acit

ors

.

Dec

imal

po

ints

fo

r re

sist

or

and

cap

acit

or

fixe

d v

alu

esar

e ex

pre

ssed

as

:2.

2

2R2

0.02

2

R02

2

A-a

A-a

A-b

E D

C KEYB

OA

RD

UN

IT

CD MECHANISM MODULE

8 9 10 11 12

16

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

PO

WE

R A

MP

RE

AR

PR

EO

UT

RE

SE

T

FM :

32d

Bs

AM

: 24

dB

sS

-CD

: 36

dB

sFM

: 5.

84d

Bs

AM

: -2

.66d

Bs

S-C

D :

9.74

dB

s

FM :

6.6d

Bs

AM

: -1

.9d

Bs

S-C

D :

10.5

dB

s

MU

TE

A-a

A-b

A-b

1 2 3

4

7

65

17

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

ERA15-02VH

ER

A15

-02V

H

ERA15-02VH

ERA15-02VH

ER

A15

-02V

H

1K(1

/2W

)

1K(1

/2W

)

RR +RR -

FR +FR -

FL +FL -

RL +RL -

ACC

GN

D

B. REM

BACK

UP

TE

LEP

HO

NE

MU

TE

ILLU

MIN

AT

ION

PO

WE

R S

UP

PLY

6

51234

65

1

2

3

4

AC

C S

EN

SE

BA

CK

UP

SE

NS

E

8V R

EG

ULA

TO

R

VD

D R

EG

ULA

TO

R

>C

EK

1136

A-b

A-a

A-b

8

9 10 11 12

18

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

B

KV

1410

(23)

KV

1410

(23)

MarkNoneF0F65F125A0A74A125

BandFMFMFMAMAMAM

Input Level0dBf65dBf125dBf0dB74dB125dB

DA

N21

7U

DA

N21

7U

3.3 FM/AM TUNER UNIT

BA

FM/AM TUNER UNIT

19

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

KV

1410

(23)

B

20

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

1 2465

3

1456 3

214

56 3

214

56 3

2

1456 3

2

1 2465

31 2

465

31 2

465

31 2

465

3

1 2465

31 2

465

31 2

465

3

1 2465

3

1 2465

31 2

465

3

1 2465

3

1 2465

3

1 2465

3

3.4 KEYBOARD UNIT

C

AC

N65

1

KEYBOARD UNIT

C

21

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

: DEH-3130R/X1N/EW, 3100R/X1N/EW: DEH-3100R-B/X1N/EW

DEH-3130R/X1N/EWCL220D CL170DCDCL170DCDCSG1114CSG1117

390

DEH-3100R-B/X1N/EWCL220SRCTSCL170SRCDCL170SRCDCSG1135CSG1133

270

DEH-3100R/X1N/EWCL220PGCCL170PGCDCL170PGCDCSG1112CSG1107

390

D1809,1810D1811D1812,1813S1801-1806,1808-1812,1816-1818S1807,1813,1814,1819

R1806,1808

C

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

BA05SFP

(SERVICE)(P8)PICKUP UNIT

PHOTO UNIT(S8)

CONTROL UNIT

SPINDLE MOTOR

Q2 CPT230SX-TUQ1 CPT230SX-TU

M3 CXB2562

CARRIAGE MOTOR

M1 CXB2190

M2 CXB2195

LOADING MOTOR

RF-AMP, SE

5V REGULATOR

CD DRIVER

CN101

CN802

CN801

3.5 CD MECHANISM MODULE

E

D

E

D22

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

MP, SERVO, DSP, DAC, LPF

SWITCHES:CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFFThe underlined indicates the switch position.

CN701

AC

N68

1

D 23

24

DEH-3130R,3100R-B,3100R

1 RFI 0.5V/div. 0.5s/div.Normal mode: play

1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Test mode: Tracking open

0.5ms/div. 1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Normal mode: The defect partpasses 800m

0.5ms/div.

3 CH1: FD 0.5V/div.4 CH2: FO+ 2V/div.

Test mode: No disc, Focus close

0.2s/div. 3 CH1: FD 0.5V/div.5 CH2: FOK 2V/div.

Normal mode: Focus close

0.2s/div. 6 CH1: FE 0.5V/div.7 CH2: XSI 2V/div.

Normal mode: Focus close

1ms/div.

REFO fi

8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 32 tracks jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: Single jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 100 tracks jump (FWD)

5ms/div.

6 CH1: FE 0.1V/div.3 CH2: FD 0.2V/div.

Normal mode: Play

20ms/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (12cm)

0.5s/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (8cm)

0.5s/div.

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

GND fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

- Waveforms

Note:1. The encircled numbers denote measuring pointes in the circuit diagram.2. Reference voltage

REFO:2.5V

REFO fi

REFO fi

REFO fi

REFO fi

25

DEH-3130R,3100R-B,3100R

8 CH1: TE 0.2V/div.9 CH2: TD 0.2V/div.

Normal mode: play

8 CH1: TE 0.5V/div.! CH2: SD 0.5V/div.TEST mode: 100 Tracks jump(FWD)

5ms/div. 0 MD 0.5V/div. 0.1s/div.

Normal mode: Play (12cm)

0 MD 1V/div. 10ms/div.Normal mode:Long Search (12cm)

@ EFM 1V/div. 5s/div.

Normal mode: play

8 CH1: TE 1V/div.# CH2: TEC 1V/div.

Test mode: Focus closeTracking open

2ms/div.

8 CH1: TE 0.5V/div.6 CH2: FE 0.5V/div.

Normal mode: AGC after focus close

0.2s/div.$ PLCK 2V/div. 0.5s/div.

Normal mode: play

20ms/div.

% SCKO 2V/div. 1s/div.

Normal mode: play

^ Dout 2V/div. 10s/div.

Normal mode: play

& LRCK 2V/div. 20s/div.

Normal mode: play

* VD 5V/div. 50ms/div.

Normal mode: No disc

GND fi

REFO fi

REFO fi

GND fi

REFO fi

REFO fi

REFO fi

REFO fiREFO fi

REFO fi

REFO fi

REFO fi

REFO fi

GND fi

REFO fi

GND fi

REFO fi

GND fi

REFO fi

GND fi

REFO fi

26

DEH-3130R,3100R-B,3100R

( CH1: R OUT 1V/div.) CH2: L OUT 1V/div.

Normal mode: Play (1kHz 0dB)

6 CH1: FE 0.2V/div.3 CH2: FD 0.5V/div.

Normal mode: During AGC

1ms/div. 8 CH1: TE 0.2V/div.9 CH2: TD 0.5V/div.

Normal mode: During AGC

1 CH1: RFI 1V/div. CH2: HOLD 5V/div.

Normal mode: The defect part passes800m(B.D)

0.2ms/div. 1ms/div.

0.5ms/div. 3 CH1: FD 0.5V/div. CH2: HOLD 5V/div.


0.5ms/div.9 CH1: TD 0.1V/div. CH2: HOLD 5V/div.


0.5ms/div.

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi

REFO fi REFO fi

REFO fi

REFO fi

REFO fi

27

DEH-3130R,3100R-B,3100R

28

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

4. PCB CONNECTION DIAGRAM4.1 TUNER AMP UNIT

NOTE FOR PCB DIAGRAMS1. The parts mounted on this PCB

include all necessary parts for

several destination.

For further information for

respective destinations, be sure

to check with the schematic dia-

gram.

2. Viewpoint of PCB diagrams

A

A

CapacitorConnector

P.C.Board Chip Part

SIDE A

SIDE B

TUNER AMP UNIT

C CN1801

CO

RD

AS

SY

CN

701

D

29

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

A

L ch R ch

SUB WOOFER/REAR PREOUT

IP BUS IN

SIDE A

BA

NT

EN

NA

CA

BLE

30

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

A

A TUNER AMP UNIT

31

DEH-3130R,3100R-B,3100R5 6 7 8

5 6 7 8

D

C

B

A

A

SIDE B

32

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

4.2 FM/AM TUNER UNIT

SIDE A

BFM

/AM

TU

NE

R U

NIT

A

33

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

SIDE B

BFM

/AM

TU

NE

R U

NIT

34

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

4.3 KEYBOARD UNIT

VO

L U

PP

.EQ

+

VO

LD

OW

N

P.E

Q

SO

UR

CE

12

34

56

TA

,TI,

PR

OG

PT

Y,

CLO

CK

DIS

P

EJE

CT F

UN

C

AU

DIO

BA

ND

C

C

SIDE A

KE

YB

OA

RD

UN

IT

35

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

C

C

SIDE B

KE

YB

OA

RD

UN

IT

AC

N65

1

36

DEH-3130R,3100R-B,3100R1 2 3 4

1 2 3 4

D

C

B

A

4.5 CD MECHANISM MODULEC

ON

TR

OL

UN

IT

HO

ME

M1

CA

RR

IAG

E M

OT

OR

M2

LOA

DIN

G M

OT

OR

M3

SP

IND

LE M

OT

OR

PIC

KU

P U

NIT

(SE

RV

ICE

)(P

8)

CN

802

CN

681

3 2 1

PH

OT

O U

NIT

(S8)

SIDE A

A D

ED

D E

E

DEH-3130R,3100R-B,3100R

D

C

B

A

37

1 2 3 4

1 2 3 4

CLA

MP

SIDE B

CO

NT

RO

L U

NIT

D

D

38

DEH-3130R,3100R-B,3100R

5. ELECTRICAL PARTS LIST

NOTES:

- Parts whose parts numbers are omitted are subject to being not supplied.

- The part numbers shown below indicate chip components.

Chip Resistor

RS1/_S___J,RS1/__S___J

Chip Capacitor (except for CQS.....)

CKS....., CCS....., CSZS.....

=====Circuit Symbol and No.===Part Name Part No.--- ------ ------------------------------------------ -------------------------

Unit Number : CWM6841Unit Name : Tuner Amp Unit

MISCELLANEOUS

IC 451 IC PML003AMIC 551 IC PAL005AIC 601 IC PE5139AIC 631 IC S-80734ANIC 701 IC PM4009A

Q 431 Transistor IMH3AQ 434 Transistor DTA124EUQ 502 Transistor 2SC4081Q 507 Transistor DTA124EUQ 524 Transistor IMH3A

Q 525 Transistor DTA114ESQ 540 Transistor 2SC1740SQ 541 Transistor 2SD1757KQ 542 Transistor 2SD1757KQ 551 Transistor DTC144ES

Q 601 Transistor DTA114ESQ 651 Transistor 2SA933SQ 652 Transistor 2SB1236Q 653 Transistor DTC124ESQ 701 Transistor DTA124ES

Q 921 Transistor 2SA1576Q 971 Transistor IMX1Q 973 Transistor 2SD1859Q 981 Transistor 2SD2396Q 982 Transistor IMD2A

Q 991 Transistor 2SD2396Q 992 Transistor IMD2AD 651 Diode MTZ5R6J(C)D 654 Diode Network DA204UD 655 Diode Network DA204U

D 656 Diode Network DA204UD 921 Diode DAN202UD 931 Diode ERA15-02VHD 932 Diode ERA15-02VHD 951 Diode ERA15-02VH

D 952 Diode ERA15-02VHD 971 Diode HZS7L(C2)D 972 Diode HZS6L(C3)D 973 Diode ERA15-02VHD 974 Diode HZS6L(B1)

D 981 Diode HZS9L(B3)D 992 Diode HZS9L(B1)L 501 Ferri-Inductor LAU4R7KL 504 Ferri-Inductor LAU2R2KL 506 Inductor LAU100K

L 601 Inductor LAU100KL 619 Ferri-Inductor LAU2R2KL 621 Ferri-Inductor LAU2R2KL 651 Ferri-Inductor LAU101KL 701 Ferri-Inductor LAU101K

L 702 Inductor LAU100KL 921 Ferri-Inductor LAU2R2KL 951 Choke Coil 600H CTH1221TH 601 Thermistor CCX1031X 601 Radiator 12.58291MHz CSS1402

X 701 Crystal Resonator 3.648MHz CSS1447FM/AM Tuner Unit CWE1500

BZ 601 Buzzer CPV1050AR 501 DSP-201M-S00B

RESISTORS

R 421 RS1/10S473JR 431 RS1/10S821JR 432 RS1/10S821JR 437 RS1/10S223JR 438 RS1/10S223J

R 443 RS1/10S0R0JR 445 RS1/8S473JR 465 RD1/4PU221JR 466 RD1/4PU221JR 502 RD1/4PU222J




R 522 RD1/4PU681JR 523 RS1/10S473JR 526 RS1/10S104JR 527 RS1/10S104JR 528 RD1/4PU102J

R 530 RS1/10S681JR 531 RS1/10S473JR 532 RD1/4PU681JR 533 RS1/10S473JR 534 RS1/10S162J



A

39

DEH-3130R,3100R-B,3100R


R 547 RS1/10S472JR 570 RD1/4PU103JR 579 RS1/10S331JR 580 RS1/10S103JR 602 RD1/4PU473J

R 603 RS1/10S102JR 606 RD1/4PU102JR 607 RD1/4PU102JR 608 RD1/4PU102JR 610 RS1/10S222J

R 611 RS1/10S473JR 613 RS1/10S0R0JR 614 RD1/4PU222JR 615 RD1/4PU473JR 616 RS1/10S222J

R 617 RS1/10S473JR 618 RN1/10SE2002DR 625 RS1/10S0R0JR 626 RD1/4PU102JR 631 RS1/10S102J

R 632 RS1/10S822JR 641 RD1/4PU102JR 651 RS1/10S222JR 652 RD1/4PU472JR 653 RS1/10S222J

R 654 RD1/4PU222JR 655 RD1/4PU222JR 656 RD1/4PU222JR 657 RS1/10S473JR 658 RD1/4PU472J

R 659 RS1/8S472JR 660 RD1/4PU302JR 662 RS2PMF200JR 681 RS1/10S681JR 682 RD1/4PU102J

R 683 RS1/10S102JR 684 RD1/4PU102JR 704 RS1/10S102JR 705 RD1/4PU102JR 706 RD1/4PU102J

R 713 RS1/10S0R0JR 714 RD1/4PU102JR 716 RS1/10S0R0JR 717 RS1/10S225JR 718 RS1/10S0R0J

R 727 RD1/4PU681JR 921 RS1/10S153JR 923 RS1/10S472JR 924 RD1/4PU102JR 925 RS1/10S473J


R 976 RS1/10S473JR 977 RD1/4PU101JR 978 RS1/10S472JR 979 RS1/10S472JR 981 RS1/10S1R0J

R 982 RD1/4PU511JR 987 RD1/4PU221JR 991 RD1/4PU221JR 992 RD1/4PU221JR 993 RS1/10S472J

R 994 RS1/10S222J

CAPACITORS

C 431 CEJA4R7M35C 432 CEAL4R7M35C 451 CKSYB224K25C 452 CKSYB224K25C 453 CKSYB474K16

C 454 CKSYB474K16C 455 CEJANP4R7M16C 456 CEJANP4R7M16C 457 CKSQYB153K50C 458 CKSQYB153K50

C 461 CEAL470M10C 462 CKSQYB104K25C 463 CEJA100M16C 465 CCSQSL182J50C 466 CCSSL182J50

C 501 CKSQYB103K50C 502 CKSQYB223K50C 503 CKSQYB223K50C 504 CEJA220M10C 505 CKSQYB102K50

C 506 CEAL101M10C 507 CKSQYB473K25C 508 CCSQCH101J50C 509 CKSQYB102K50C 519 CKSQYB472K50

C 524 CEJA1R0M50C 525 CEJA1R0M50C 531 CKSQYB182K50C 536 CKSQYB123K50C 537 CKSQYB123K50

C 540 CKSQYB223K50C 551 CKSYB224K25C 552 CKSYB224K25C 553 CKSYB224K25C 554 CKSYB224K25

C 556 4700F/16V CCH1328C 570 CEJA100M16C 571 CEJA330M10C 572 CKSYB105K16C 573 CKSYB104K50

C 601 CCSQCH200J50C 602 CCSQCH200J50C 603 CKSYB105K16C 604 CEJA4R7M35C 605 CCSQCH101J50

C 607 CCSQCH101J50C 609 CCSQCH101J50C 619 CCSQCH101J50C 621 CCSQCH101J50C 622 CCSQCH101J50

C 631 CEJA2R2M50C 652 CEJA4R7M35C 653 CKSQYB473K25C 701 CEAL220M6R3C 702 CKSQYB104K25



40

DEH-3130R,3100R-B,3100R

C 711 CCSQCH270J50C 712 CCSQCH270J50C 715 CKSQYB104K50C 717 CKSQYB471K50C 718 CKSYB471K50

C 721 CEAL220M6R3C 722 CKSQYB104K25C 971 470F/16V CCH1331C 972 CKSQYB473K25C 973 CEJA101M10

C 974 CKSQYB473K25C 981 330F/16V CCH1326C 982 CKSQYB103K50C 983 CEJA101M16C 991 CKSQYB473K25

C 992 CKSQYB102K50C 993 CEJA101M10

Unit Number : CWE1500Unit Name : FM/AM Tuner Unit

MISCELLANEOUS

IC 1 IC PML002AIC 2 IC PM4008AIC 3 IC BR9010FVQ 1 Transistor 2SC4081Q 2 Transistor DTC124EU

Q 3 FET 3SK263Q 51 Transistor 2SC4081Q 201 FET 2SK932Q 202 Transistor DTC124EUQ 204 Transistor 2SC4081

D 1 Diode KV1410(23)D 2 Diode 1SV248D 4 Diode KV1410(23)D 6 Diode KV1410(23)D 101 Diode 1SS355

D 201 Diode DAN217UD 202 Diode DAN217UD 903 Diode KV1410(23)D 904 Diode SVC253L 1 Coil CTC1155

L 2 Coil CTC1155L 3 Inductor LCTB100K2125L 4 Coil CTC1155L 201 Inductor LCTB330K1608L 202 Inductor CTF1287

L 203 Inductor LCTA121J3225L 901 Coil CTC1154L 902 Inductor LCTA3R3J3225L 904 Inductor LCTBR47K1608L 905 Inductor LCTBR47K1608

T 51 Coil CTE1132CF 51 Ceramic Filter CTF1442CF 52 Ceramic Filter CTF1442CF 53 Ceramic Filter CTF1442CF 202 Ceramic Filter CTF1348

X 901 Crystal Resonator 10.250MHz CSS1432

RESISTORS







R 104 RS1/16S562JR 106 RS1/16S0R0JR 108 RS1/16S0R0JR 110 RS1/16S154JR 111 RS1/16S273J


R 117 RS1/16S333JR 118 RS1/16S223JR 122 RS1/16S0R0JR 202 RS1/16S472JR 203 RS1/16S225J



R 907 RS1/16S103JR 908 RS1/16S681JR 909 RS1/16S473JR 914 RS1/16S562J

CAPACITORS

C 1 CCSQCH5R0C50C 2 CCSRCH5R0C50C 4 CCSRCJ3R0C50C 6 CKSQYB105K10C 8 CKSRYB222K50

C 10 CCSRCH220J50C 11 CCSRCH150J50C 12 CCSRCH8R0D50C 14 CCSRCJ3R0C50C 15 CKSRYB103K50



B

41

DEH-3130R,3100R-B,3100R

C 16 CKSRYB222K50C 17 CKSRYB222K50C 18 CCSRCJ3R0C50C 19 CKSRYB103K50C 20 CKSRYB103K50

C 21 CKSRYB103K50C 24 CKSQYB334K16C 31 CKSRYB222K50C 32 CCSRCH470J50C 35 CKSRYB103K50

C 51 CKSRYB103K50C 52 CKSRYB473K16C 53 CCSRCK2R0C50C 54 CKSRYB103K50C 55 CKSRYB104K16

C 56 CKSRYB104K16C 58 CKSQYB224K16C 59 CKSRYB223K25C 60 CKSRYB104K16C 101 CEALNP100M10

C 102 CCSRCH151J50C 103 CKSRYB473K16C 105 CKSRYB682K25C 106 CEAL2R2M50C 107 CKSRYB103K50

C 108 CKSQYB474K16C 109 CKSQYB474K16C 110 CKSRYB104K16C 111 CKSRYB104K16C 112 CKSRYB104K16

C 113 CKSRYB123K25C 114 CEAL220M6R3C 115 CKSRYB473K16C 116 CEAL2R2M50C 117 CKSRYB102K50

C 120 CKSRYB153K25C 121 CKSRYB332K50C 122 CKSRYB682K25C 123 CKSRYB681K50C 125 CKSRYB103K50

C 126 CKSRYB103K50C 127 CEAL2R2M50C 128 CKSRYB103K50C 201 CCSRCH471J50C 202 CCSRCH100D50


C 208 CCSRCH560J50C 209 CEAL470M6R3C 210 CKSRYB103K50C 211 CKSRYB103K50C 212 CCSRCH101J50

C 215 CKSRYB223K25C 216 CKSQYB334K16C 217 CKSRYB103K50C 219 CKSQYB105K10C 220 CKSRYB104K16

C 221 CKSRYB473K16C 222 CKSQYB334K16C 223 CKSQYB474K16C 224 CKSRYB104K16C 225 CKSRYB272K50

C 226 CKSRYB682K25C 902 CCSRCH270J50C 904 CKSRYB223K25C 905 CKSRYB103K50C 906 CCSRTH100D50

C 907 CCSRTH150J50C 909 CCSRTH100D50C 910 CKSRYB332K50C 912 CKSQYB474K16C 913 CKSRYB223K25

C 914 CKSRYB682K25C 915 CKSQYB223K25C 916 CKSQYB474K16C 917 CKSYB475K10C 918 CKSRYB223K25

C 919 CKSQYB225K10C 920 CCSRCH270J50C 921 CCSRCH270J50C 922 CKSYB105K16C 923 CKSRYB103K50

Unit Number : CWM6796Unit Name : Keyboard Unit

: (DEH-3130R/X1N/EW)

MISCELLANEOUS

IC 1801 IC PD6294AD 1801 Diode Network DA204UD 1802 Diode Network DA204UD 1803 LED NSSW440-9159D 1804 LED NSSW440-9159

D 1807 LED NSSW440-9159D 1808 LED NSSW440-9159D 1809 LED CL220DD 1810 LED CL220DD 1811 LED CL170DCD

D 1812 LED CL170DCDD 1813 LED CL170DCDX 1801 Radiator 5.00MHz CSS1423S 1801 CSG1114S 1802 CSG1114

S 1803 CSG1114S 1804 CSG1114S 1805 CSG1114S 1806 CSG1114S 1807 CSG1117




LCD CAW1570

RESISTORS




C

42

DEH-3130R,3100R-B,3100R



R 1819 RS1/10S0R0JR 1821 RS1/4S272J

CAPACITORS

C 1801 CKSQYB104K50C 1803 CKSQYB104K50C 1804 CKSQYB104K50C 1805 CKSQYB104K50C 1806 CKSQYB104K50

C 1807 CKSQYB104K50C 1808 CKSQYB104K50C 1811 CKSQYB104K50C 1812 CKSQYB104K50


: (DEH-3100R-B/X1N/EW)

MISCELLANEOUS


D 1807 LED NSSW440-9159D 1808 LED NSSW440-9159D 1809 LED CL220SRCTSD 1810 LED CL220SRCTSD 1811 LED CL170SRCD

D 1812 LED CL170SRCDD 1813 LED CL170SRCDX 1801 Radiator 5.00MHz CSS1423S 1801 CSG1135S 1802 CSG1135





LCD CAW1572

RESISTORS




R 1819 RS1/10S0R0JR 1821 RS1/4S272J

CAPACITORS




: (DEH-3100R/X1N/EW)

MISCELLANEOUS


D 1807 LED NSSW440-9159D 1808 LED NSSW440-9159D 1809 LED CL220PGCD 1810 LED CL220PGCD 1811 LED CL170PGCD

D 1812 LED CL170PGCDD 1813 LED CL170PGCDX 1801 Radiator 5.00MHz CSS1423S 1801 CSG1112S 1802 CSG1112

S 1803 CSG1112S 1804 CSG1112S 1805 CSG1112S 1806 CSG1112S 1807 Switch CSG1107


S 1813 Switch CSG1107S 1814 Switch CSG1107S 1815 CSG1111S 1816 CSG1112S 1817 CSG1112



C

C

43

DEH-3130R,3100R-B,3100R

S 1818 CSG1112S 1819 Switch CSG1107S 1820 CSG1111S 1821 CSG1111S 1822 CSG1111

LCD CAW1570

RESISTORS




R 1819 RS1/10S0R0JR 1821 RS1/4S272J

CAPACITORS



Unit Number : CWX2411Unit Name : Control Unit

MISCELLANEOUS

IC 201 IC UPD63711GCIC 301 IC BA5985FMIC 701 IC BA05SFPQ 101 Transistor 2SB1132D 801 LED CL200IRX

D 802 LED CL200IRXX 201 Ceramic Oscillator 16.934MHz CSS1456S 801 Spring Switch(HOME) CSN1051S 802 Spring Switch(CLAMP) CSN1052

RESISTORS



R 302 RS1/16S153JR 303 RS1/16S103JR 501 RS1/16S102JR 502 RA4C681JR 601 RS1/16S102J

R 602 RS1/16S102JR 605 RS1/16S0R0JR 606 RS1/16S0R0JR 801 RS1/8S751JR 803 RS1/8S751J

R 902 RS1/16S0R0JR 906 RS1/16S0R0J

CAPACITORS

C 101 CCSRCH102J25C 102 CKSRYB104K16C 103 CEV101M6R3C 104 CEV470M6R3C 105 CKSQYB334K16

C 106 CKSQYB334K16C 107 CKSQYB334K16C 201 CKSRYB104K16C 202 CKSRYB471K50C 203 CKSRYB104K16

C 205 CEV101M6R3C 206 CKSRYB104K16C 207 CKSRYB104K16C 208 CKSRYB104K16C 209 CKSRYB104K16


C 215 CKSRYB104K16C 216 CCSRCJ3R0C50C 217 CCSRCH270J50C 218 CKSRYB104K16C 219 CCSRCH181J50

C 220 CCSRCH510J50C 221 CKSRYB682K25C 222 CEV220M6R3C 223 CKSRYB103K25C 224 CKSRYB224K10

C 301 CEV101M10C 603 CCSQSL152J50C 604 CCSQSL152J50C 702 10F/10V CCH1349C 703 CKSQYB334K16

Unit Number :Unit Name : Photo Unit(S8)

Q 1 Photo-transistor CPT230SX-TUQ 2 Photo-transistor CPT230SX-TU

Miscellaneous Parts List

Pickup Unit(Service)(P8) CXX1285M 1 Motor Unit(CARRIAGE) CXB2190M 2 Motor Unit(LOADING) CXB2195M 3 Motor Unit(SPINDLE) CXB2562

Fuse(10A) CEK1136



D

E

44

DEH-3130R,3100R-B,3100R

1) Precautions This unit uses a single power supply (+5V) for the reg-

ulator. The signal reference potential, therefore, isconnected to REFO(approx. 2.5V) instead of GND.If REFO and GND are connected to each other by mis-take during adjustments, not only will it be impossi-ble to measure the potential correctly, but the servowill malfunction and a severe shock will be applied tothe pick-up. To avoid this, take special note of the fol-lowing.Do not connect the negative probe of the measuringequipment to REFO and GND together. It is especiallyimportant not to connect the channel 1 negativeprobe of the oscilloscope to REFO with the channel 2negative probe connected to GND.Since the frame of the measuring instrument is usual-ly at the same potential as the negative probe, changethe frame of the measuring instrument to floating sta-tus.If by accident REFO comes in contact with GND,immediately switch the regulator or power OFF.

Always make sure the regulator is OFF when connect-ing and disconnecting the various filters and wiringrequired for measurements.

Before proceeding to further adjustments and mea-surements after switching regulator ON, let the playerrun for about one minute to allow the circuits to stabi-lize.

Since the protective systems in the unit's software arerendered inoperative in test mode, be very careful toavoid mechanical and /or electrical shocks to the sys-tem when making adjustment.

Disc detection during loading and eject operations isperformed by means of a photo transistor in thisunit.Consequently, if the inside of the unit is exposedto a strong light source when the outer casing isremoved for repairs or adjustment, the following mal-functions may occur.

*During PLAY, even if the eject button ispressed,the disc will not be ejected and the unitwill remain in the PLAY mode.

*The unit will not load a disc.When the unit malfunctions this way, either re-posi-tion the light source, move the unit or cover the phototransistor.

2) Test ModeThis mode is used for adjusting the CD mechanismmodule of the device.

Test mode starting procedureReset while pressing the 4 and 6 keys together.

Test mode cancellationSwitch ACC, back-up OFF.

After pressing the EJECT key, do not press any otherkey until the disk is completely ejected.

If the ] or [ key is pressed while focus search is inprogress, immediately turn the power off (otherwisethe actuator may be damaged due to adhesion of thelenses).

Jump operation of TRs other than 100TR continuesafter releasing the key. CRG move and 100TR jumpoperations are brought into the Tracking close sta-tus when the key is released.

Powering Off/On resets the jump mode to Single TR(91), the RF AMP gain setting to 0 dB, and the auto-matic adjustment value to the initial value.

6. ADJUSTMENT6.1 CD ADJUSTMENT

DEH-3130R,3100R-B,3100R

45

- Flow Chart

Focus Close*2 S Curve Check01 01 0100 00 00

(99 99 99)Display

TYP

4

3

Reset

SOURCE

New test mode

6

[

BAND

BAND

BAND

BAND

BAND

3

*2

*1 +6dB +12dB

*4

*5

6

6

6

6

1

2

1

2]

] [

06 06 06 12 12 12

Select CD

Single TR 32TRK92(82)

CRG Move94(84)

100TRK93(83)

Focus ModeSelect

Focus Close/S Curve Check

CRG- Auto AdjustmentDisplay Select

CRG+

RF AGC Coefficient Display/Rough Servo and RF AGC

Tracking Open

Display

TrackingOpen

T. Close andFit Servo

*3 F.Offset Display RF.Offset Display F.Cansel Display

*7

Single TR/32TR/100TR

Voltage of CRG Motor = 2 [V]

(F,T.AGC Gain = (Present Value/Initial Value) 20)

*6

] [

1

3

Display

2

3

Displayor

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

CRG-CRG+ T.BalanceAdjustment

*7F, T, RF AGC/F.Bias Display Select

F, T AGC andRF AGC

CRG Move, 100TR Jump Only

TRK, MIN, SEC F.AGC Gain RF AGC GainT.AGC Gain

*8

Power ON(Adjustment for T.Offset)

*5 *4 *4

*6CRG/TR Jump NO.Select

CRG+/TR Jump+

CRG-/TR Jump-

Power OFF

Display

Display

Display

T.Close andF,T AGC andRF AGC andFit Servo

Display

Power ON(Not adjustment for T.Offset)

Display

Display

2

RF AMP Gain Select

2

Power OFF

Power OFF

Power OFF 8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

91 91 91TRK SECMIN

0x 0x 0xTRK SECMIN

00 00 00TRK SECMIN

99 99 99TRK SECMIN

GG GG GGTRK SECMIN

Test Mode In

*1

*8 *3*8

F.Cancel Value = {Top Rank 8bit of Set Value (7F [H] to 80 [H] ) + 128} / 4 = 63 [D] to (32 [D] ) to 00 [D]

9x(8x):91(81)

46

DEH-3130R,3100R-B,3100R

Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjustedPU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, ifthe PU unit must be changed, the grating should be checked using the procedure below.

Purpose :To check that the grating is within an acceptable range when the PU unit is changed.

Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to performtrack search operations, or taking a long time for track searching.

Method : Measuring Equipment Oscilloscope, Two L.P.F. Measuring Points E, F, REFOUT Disc ABEX TCD-784 Mode TEST MODE

Checking Procedure1. In test mode, load the disc and switch the 5V regulator on.2. Using the ] and [ buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-

ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on thefourth press.

4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-ence is within 75 . Refer to the photographs supplied to determine the phase angle.

5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is anyimprovement. If, after trying this a number of times, the grating angle does not become less than 75 then themechanism should be judged to be at fault.

NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may beseen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-age angle.

HintReloading the disc changes the clamp position and may decrease the "wobble".

F

REFO

E

100kW

390pF

100kW

390pF

E

REFO

F

REFO

L.P.F.

L.P.F.

CONTROL UNIT

Xch Ych

Oscilloscope

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

DEH-3130R,3100R-B,3100R

47

Grating waveform Ech fi Xch 20mV/div, ACFch fi Ych 20mV/div, AC

45

0

75

60

30

90

48

DEH-3130R,3100R-B,3100R

7. GENERAL INFORMATION7.1 DIAGNOSIS

7.1.1 TEST MODE- Error Messages

If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the

error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the

users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (min-

utes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains

in blank as before.

2) Head unit display examples

Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERRORxx ERRxx Exx

OR

Errxx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)

10 Electricity Carriage Home NG CRG can't be moved to inner diameter.

CRG can't be moved from inner diameter.

fi Failure on home switch or CRG move mechanism.

11 Electricity Focus Servo NG Focusing not available.

fi Stains on rear side of disc or excessive vibrations on REWRITABLE.

12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).

fi Failure on spindle, stains or damages on disc, or excessive vibrations.

Subcode NG A disc not containing CD-R data is found. Turned over disc are found,

though rarely.

fi Failure on home switch or CRG move mechanism.

RF AMP NG An appropriate RF AMP gain can't be determined.

fi CD signal error.

17 Electricity Setup NG APC protection doesn't work. Focus can be easily lost.

fi Damages or stains on disc, or excessive vibrations.

30 Electricity Search Time Out Failed to reach target address.

fi CRG tracking error or damages on disc.

A0 System Power Supply NG Power (VD) is ground faulted.

fi Failure on SW transistor or power supply (failure on connector).

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).

Unreadable TOC does not constitute an error. An intended operation continues in this case.

A newly designed head unit must conform to the example given above.

Upper digits of an error code are subdivided as shown below:

1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.

49

DEH-3130R,3100R-B,3100R

- New Test ModeS-CD plays the same way as before.

If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its

cause and time occurred (in absolute time) are displayed.

During setup, operational status of the control software (internal RAM: CPOINT) is displayed.

These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.

(1) Shifting to the New Test Mode

1 Turn on the current test mode by starting the reset from the key.

2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the

disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.

3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.

You can reset the new test mode by turning on the reset start.

* With some products, the new test mode can be reset through the same operations as that employed for shifting to

the STBY mode (while maintaining the Acc turned off).

(2) Key Correspondence

Key Test mode New test mode

(Example) Power Off Power On In-play Error Production

BAND To power on To power off Time/Err.No. switching

(offset adjustment performed)

] FWD-Kick FF/TR+

[ REV-Kick REV/TR-

1 T.Close (AGC performed) Scan

/parameter display switching

2 RF AMP gain switching Parameter display switching Mode

/T.BAL adjustment/T.Open

3 To power on F.Close/RF AGC/F.T.AGC

(offset adjustment not performed)

6 F.Mode switching Auto/Manu T.No./Time switching

/T.Close (no AGC)/Jump switching

Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.

(3) Cause of Error and Error Code

Code Class Contents Description and cause

40 Electricity Off focus detected. FOK goes low.

fi Damages/stains on disc, vibrations or failure on servo.

41 Electricity Spindle unlocked. FOK = Low continued for 50 msec.


42 Electricity Sub-code unreadable. Sub-code was unreadable for 50 msec.


43 Electricity Sound skipping detected. Last address memory function was activated.


Note: Mechanical errors during aging are not displayed.

The error codes should be indicated in the same way as in the normal mode.

50

DEH-3130R,3100R-B,3100R

(4) Display of Operational Status (CPOINT) during SetupStatus No. Contents Protective action00 CD+5V ON process in progress. None01 Servo LSI initialization (1/3) in progress. None02 Servo LSI CRAM initialization in progress. None03 Servo LSI initialization (2/3) in progress. None04 Offset adjustment (1/3) in progress. None05 Offset adjustment (2/3) in progress. None06 Offset adjustment (3/3) in progress. None07 FZD adjustment in progress. None08 Servo LSI initialization (3/3) in progress. None10 Carriage move to home position started. None11 Carriage move to home position started. None12 Carriage is moving toward inner diameter. Specified 10 seconds has been passed or failure

on home switch.13 Carriage is moving toward outer diameter. Specified 10 seconds has been passed or failure

on home switch.14 Carriage outer kick in progress. None15 Carriage outer diameter feed (1 second) in progress. None20 Servo close started. None21 Pre-processing for focus search started. None22 Spindle rotation and focus search started. None23 Waiting for focus close (XSI=Low). Specified focus search time has been passed.24 Standing by after focus close is over. Specified focus search time has been passed.25 Focus search preprocessing is in None

progress while setup protection is turned on.26 Focus search preprocessing is in None

progress while focus recovery is turned on.27 Wait time after focus close is set up. Off focus.28 Standing by after focus close is over. Off focus.29 Setup (1/2) before T balance adjustment is started. Off focus.30 Setup (2/2) before T balance adjustment is started. Off focus.31 T balance adjustment started. Off focus.32 T balance adjustment (1/2). Off focus.33 T balance adjustment (2/2). Off focus.34 Waiting for spindle rotation to end. Off focus.

Spindle rough servo.35 Standing by after spindle rough servo is over. Off focus.36 RF AGC started. Off focus.37 RF AGC started. Off focus.38 RF AGC ending process in progress. Off focus.39 Tracking close in progress. Off focus.40 Standing by after tracking is closed. Off focus.

Carriage closing in progress.41 Focus/tracking AGC started. Off focus.42 Focus AGC started. Off focus.43 Focus AGC in progress. Off focus.44 Tracking AGC in progress. Off focus.45 Standing by after focus/tracking AGC are over. Off focus.46 Spindle processes applicable servo. Off focus.47 Check for servo close is started. Off focus.48 Check of LOCK pin started. Off focus or spindle not locked.49 RF AGC started. Off focus.50 RF AGC in progress. Off focus.51 Standing by after RF AGC is over. Off focus.

51

DEH-3130R,3100R-B,3100R

(5) Display Examples

1) During Setup (When status no. = 11)

TRK No. MIN. SEC.

11 11' 11"

2) During Operation (TOC read, TRK search, Play, FF and REV)

The same as in the normal mode.

3) When a Protection Error Occurred

Switch to the following displays (A) and (B) using the [BAND] switch:

(A) Error occurrence timing display in absolute time.

An example: Error occurred in 12th tune at 34'56" in absolute time.

TRK No. MIN. SEC.

12 34' 56"

(B) Error No. display

An example: Error #40 (Off focus is detected)

ERROR-40

52

DEH-3130R,3100R-B,3100R

7.1.2 DISASSEMBLY

- Removing the Tuner Amp Unit(Fig.2)

Remove the two screws.

Remove the three screws.

Remove the screw.

Straighten the tabs at four locations indi-

cated.

Remove the Tuner Amp Unit.

- Removing the Case Unit(not shown)1.Remove the Case Unit.

- Removing the Panel Assy(Fig.1)

Disengage the stoppers at two locations.

Remove the Panel Assy.

- Removing the CD Mechanism Module

(not shown)1.Remove the four screws.

2.Disconnect the connector, and then remove the

CD Mechanism Module.

Fig.1

Fig.2

Panel Assy

Tuner Amp Unit

53

DEH-3130R,3100R-B,3100R

- Removing the Upper Frame1. Remove six Springs A, two Springs B and four

Screws.

2. Remove two Tabs situated on rear side of the Upper

Frame, remove two Arms on the front side, then

remove two Tabs on the front side.

- Removing the Carriage Mechanism1. Disengage the Carriage Mechanism from the two

dampers situated in the front side by driving it up,

then disengage and remove the mechanism from the

one damper by driving it up aslant into front side

direction.

Note : When assembling the Carriage Mechanism, coat

the dampers with alcohol prior to the assembly.

- Removing the Clamp Arm Assy1. Remove a Spring A, a B and a Spring C.

2. Drive the Clamp Arm Assy up into rear side direction,

then disengage the arm from its current position

Finally, drive the assembly approximately 45 degrees

upward, then slide the assembly toward right side to

remove it.

B

A

B A

A

A

Arm

Arm

A

B

C

Upper Frame

Carriage Mechanism Section

Clamp Arm Assy Section

A

A

54

DEH-3130R,3100R-B,3100R

- Removing the Guide Arm Assy1. Remove a connector, a spring A and B

2. Drive the Guide Arm Assy up aslant into rear side

direction, then remove it from a Pin. Finally, drive the

assembly approximately 45 degrees upward, then

slide the assembly toward left side to remove it.

Note : When assembling the guide arm assembly, route

the cord inside the assembly. In this operation,

care must be exercised so that cord may be

caught by the gear.

- Removing the LO Arm Assy1. Remove two Pins to dismount the LO Arm Assy.

- Removing the Control Unit and the Spindle

Motor1. Remove from the connector after mounting the short

pin on the flexible PCB of the pickup unit.

2. Remove two Soldered joints, then remove two

Screws A.

3. Remove two connectors and a Screw B.

4. Disengage the Control Unit from two Tabs, then dis-

mount the unit by sliding it toward left.

5. Dismount the Spindle Motor.

A

Guide Arm Assy Section

B

Pin

LO Arm Assy Section

Spindle Motor

A A

Control Unit

Short Pin

B

55

DEH-3130R,3100R-B,3100R

- Removing the Loading Motor and Carriage

Motor1. Remove the Spring and two Screws A.

2. Dismount the Loading Motor.

3. Remove the Belt, a Screw B, two Screws C, a Guide

and a Screw Unit.

4. Dismount the Carriage Motor.

Note : When assembling the Belt, use care so that it

may not be contaminated by grease.

- Removing the Pickup Unit1. Remove two Screws and a Shaft.

2. Dismount the Pickup Unit.

Pickup Unit

Shaft

CGuide

B

Screw Unit Carriage Motor

AA

CBelt

Loading Motor

56

DEH-3130R,3100R-B,3100R

7.1 PARTS

7.2.1 IC- Pin Functions (PE5139A)

Pin No. Pin Name I/O Function and Operation1 DRSYS O Door system select output2 TELMUTE I Telephone mute input3 SYSPW O System power supply control output4 DRELAY O External relay output5 TESTIN I Test program mode input6 drst O RDS reset output7 ERROR O RDS disapprove of error correction output8 sk I RDS SK signal input9 RECIVE O During RDS data reception output

10 TUNPW O Tuner power control output11 reset I Reset input12 XT2 Not used (open)13 XT1 Not used (GND)14 VSS GND15 X2 Crystal oscillator connection pin16 X1 Crystal oscillator connection pin17 REGOFF Connect to VSS18 REGC Capacitor for regulator connect pin19 VDD Power supply20 GRNILM O Green illumination select output21 NC Not used22 adpw O A/D converter power supply output

23,24 NC Not used25 ASENBO O Slave power supply control output26 ROMDATA O ROM correction data output27 ROMCLK O ROM correction clock output28 MUTE O System mute output29 fm/AM O RDS decoder power select output30 LOCL O LOCL output31 LOCH O LOCH output32 TUNPCE2 O PLL IC chip enable output33 VCK O Clock output for electronic volume34 VST O Strobe pulse output for electronic volume35 VDT O Data output for electronic volume36 tmute O Tuner mute output37 ROMCS O ROM correction chip select output38 SD I SD input 39 st I FM stereo input40 VSS GND41 VDD Power supply

42,43 NC Not used44 rdslk I RDS LK signal input45 currq O Tuner voltage FIX output46 RDT I RDS demodulation data input

4750 NC Not used51 swvdd O Keyboard unit power supply control output52 dsens I Grille detach sense input53 CONT O CD server driver power control output54 CD5VON O CD +5V power control output55 NC Not used56 VDCONT O CD VD power control output57 CDMUTE O CD mute control output58 CDEJET O CD eject control output59 CDLOAD O CD LOAD motor loading control output60 LOCK I CD spindle lock input

57

DEH-3130R,3100R-B,3100R

IC's marked by* are MOS type.

Be careful in handling them because they are very

liable to be damaged by electrostatic induction.

*PE5139A

30

31

50

51 80

81

100

1

Pin No. Pin Name I/O Function and Operation61 FOK I CD focus OK input62 PCL O Clock adjustment output63 MIRR I CD mirror detector input64 clamp I CD disc clamp sense input65 xsck O CD LSI clock output66 XSI I CD LSI data input67 XSO O CD LSI data output68 XA0 O CD LSI command/data control output69 xrst O CD LSI reset output70 xstb O CD LSI strobe output

71,72 NC Not used73 TEST I Test terminal74 SL I Tuner signal level input75 MODEL1 I Model select input76 NL1 I RDS noise level input77 SDBW I SD bandwidth input78 EJTSNS I CD disc EJECT position detect79 DSCSNS I CD disc detect input80 VDSENS I CD VD over voltage / short-circuit sense input81 TEMP I CD temperature sense input (CD)82 (VDD) A/D converter power supply terminal83 (VDD) A/D converter reference voltage terminal84 (GND) A/D converter GND

85,86 NC Not used87 GND GND88 ldet I RDS PLL lock sense input89 rck I RDS demodulation clock input90 RDS57K I RDS 57kHz pulse count input91 SRVCNT Not used92 asens I ACC power sense input93 bsens I Back up power sense input94 TUNPDI I PLL IC data input95 KEYDT I Key data input96 DPDT O Display data output97 TUNPCK O PLL IC clock output98 TUNPDO O PLL IC data output99 TUNPCE O PLL IC chip enable

100 PEE O Beep tone output

58

DEH-3130R,3100R-B,3100R

- Pin Functions (PD6294A)Pin No. Pin Name I/O Function and Operation

1 VSS GND2 X1 Crystal oscillator connection pin3 X0 Crystal oscillator connection pin4 NC Not used

5,6 MOD1,0 I Connect to GND7 NC Not used8 KYDT O Key data output9 DPDT I Display data input

10 REMIN I Remote control pulse input11,12 NC Not used13-16 kd$-kd! I Key data input17-22 KST6-KST1 O Key strobe output

23 VDD VDD24-73 SEG49-0 O LCD segment output74-77 COM3-0 O LCD common output

78 VLCD I LCD voltage input79,80 V2,V1 Power supply terminal

*PD6294A

20

21

40

41 60

61

80

1

PAL005A

1 2 3 4 5 6 7

Mute

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Mute Mute Mute

STBY

Protector

Amp2 Amp1 Amp3 Amp4

TAB

P-G

ND

2

OU

T2-

OU

T2+

ST

BY

VC

C

OU

T1-

OU

T1+

P-G

ND

1

P-G

ND

3

P-G

ND

4

Sw

itch

_ou

t

MU

TE

OU

T4+

OU

T4-

SV

R

IN1

IN2

IN4

S-G

ND

IN3

Ac_

gn

d

OU

T3+

OU

T3-

VC

C

BR9010FV

NC

VCC

CS

SK

WC

GND

DO

DI

1

2

3

4

8

7

6

5

CSSKDIDOWC

: Chip select input: Serial data clock input: Serial data input: Serial data output: Write control input

59

DEH-3130R,3100R-B,3100R

1 2 3 4 5 6 7 8 9 10 11 12 13 14

1516171819202122232425262728

Vref IN1_L IN2_L IN3_L IN4+_L AGND Loud- out_L

SVin_L Front- out_L

Rear- out_L

FIE_L DGNDIN4-_L CLK

VCC IN1_R IN2_R IN3_R IN4+_R AGNDLoud- out_R SVin_R

Front- out_R

Rear- out_R FIE_R STBIN4-_R DATA

Isolator circuit

Primary volume

Anti Alias filter

Treble

Anti radiation filter

Middle Bass

Loudness volume

FIE

Fadervolume

Secondary volume

Zero crossdetect circuit

Primary volume

Anti Alias filter

Middle

Treble

Bass

Isolator circuit

Anti radiation filter

Loudness volume

Zero crossdetect circuit

Fadervolume

Secondary volume

FIE

Digital block

Auto-Zero

Auto-Zero

PML003AM

PM4009A

60

DEH-3130R,3100R-B,3100R

- Pin Functions (UPD63711GC)Pin No. Pin Name I/O Function and Operation

1 D.GND Logic circuit GND2 RFOK O RFOK signal output3 rst I Reset signal input4 A0 I Command/parameter identification signal input5 stb I Data strobe signal input6 sck I Clock signal input for serial data input/output7 SO O Serial data and status signal output8 SI I Serial data input9 xtalen I Crystal oscillation control pin

10 D.VDD Positive power supply terminal to logic circuit11 DA.VDD Positive power supply terminal to D/A converter12 R_OUT O Right channel audio output signal13 DA.GND D/A converter GND14 REGC I The outside putting capacitor connection pin for SCF regulator15 DA.GND D/A converter GND16 L_OUT O Left channel audio output signal17 DA.VDD Positive power supply terminal to D/A converter18 R+ O Right channel audio data output19 R- O Right channel audio data output20 L- O Left channel audio data output21 L+ O Left channel audio data output22 X.VDD Positive power supply terminal to crystal oscillation circuit23 XTAL I Crystal oscillator connect pin24 xtal O Crystal oscillator connect pin25 X.GND Crystal oscillation circuit GND26 D.VDD Positive power supply terminal to logic circuit27 EMPH O Output pin for the pre-emphasis data in the sub-Q code28 FLAG O Flag output pin to indicate that audio data currently being output consists

of noncorrectable data29 DIN I Serial data input to internal DAC30 DOUT O Serial audio data output31 SCKIN I Serial clock input to internal DAC32 SCKO O Audio data that is output from DOUT changes at rising edge of this clock33 LRCKIN I LRCK signal input to internal DAC34 LRCK O Signals to distinguish the right and left channels of the audio data output

from DOUT35 HOLD O Defect detection output36 TX O Digital audio interface data output37 D.GND Logic circuit GND38 C16M O Oscillator clock buffering output39 LIMIT I Status of the pin is output at Bit 5 of the status output40 D.VDD Positive power supply terminal to logic circuit41 LOCK O EFM synchronous detection signal42 RFCK O Frame synchronous signal of XTAL-system43 MIRR O MIRR output44 PLCK O Monitor pin of bit clock45 D.GND Logic circuit GND46 C1D1 O Output pin for indicating the C1 error correction results47 C1D2 O Output pin for indicating the C1 error correction results48 C2D1 O Output pin for indicating the C2 error correction results49 C2D2 O Output pin for indicating the C2 error correction results50 C2D3 O Output pin for indicating the C2 error correction results51 D.VDD Positive power supply terminal to logic circuit52 PACK O CD-TEXT PACK synchronous signal53 TSO O CD-TEXT data serial output54 TSI I CD-TEXT control parameter serial input55 tsck I CD-TEXT serial clock input56 TSTB I CD-TEXT parameter strobe signal input57 D.GND Logic circuit GND

61

DEH-3130R,3100R-B,3100R

Pin No. Pin Name I/O Function and Operation58 TEST0 I Test pin59 TEST1 I Test pin60 ATEST O Test pin61 A.GND Analog circuit GND62 FD O Focus drive output63 TD O Tracking drive output64 SD O Sled drive output65 MD O Spindle drive output66 DAC0 O DAC output for adjustment67 DAC1 O DAC output for adjustment68 DAC2 O DAC output for adjustment69 DAC3 O DAC output for adjustment70 A.VDD Positive power supply terminal to analog circuit71 EFM O EFM signal output72 ASY I EFM comparator reference voltage input73 C3T 3T detection capacitor additional pin74 RFI I RF signal input for EFM data regulation75 AGCO O RF signal output of after gain adjustment 76 AGCI I RF-AGC amplifier input77 RFO O RF summing amplifier output78 EQ2 RF amplifier equalizer parts additional pin79 EQ1 RF amplifier equalizer parts additional pin80 RF- I RF summing amplifier inverted input81 A.GND Analog circuit GND82 A I Photo detector A input83 C I Photo detector C input84 B I Photo detector B input85 D I Photo detector D input86 F I Photo detector F input87 E I Photo detector E input88 A.VDD Positive power supply terminal to analog circuit89 REFOUT O Reference electric potential output90 FE- I Focus error amplifier inverted input91 FEO O Focus error amplifier output92 TE- I Tracking error amplifier inverted input93 TEO O Tracking error amplifier output94 TE2 O Tracking error output of after amplification95 TEC I Tracking comparator input96 A.GND Analog circuit GND97 PD I PD detection signal input for LD output monitor 98 LD O LD control current output99 PN I APC circuit control polarity set pin

100 A.VDD Positive power supply terminal to analog circuit

20

21

40

41 60

61

80

1

100

76

26

125

7551

50

*UPD63711GC

62

DEH-3130R,3100R-B,3100R

- Pin Functions (BA5985FM)Pin No. Pin Name I/O Function and Operation

1 FWD I Loading driver FWD input2 OPIN1(+) I CH1 pre-amplifier input3 OPIN1(- ) I CH1 pre-amplifier inverted input4 OPOUT1 O CH1 pre-amplifier output5 OPIN2(+) I CH2 pre-amplifier input6 OPIN2(- ) I CH2 pre-amplifier inverted input7 OPOUT2 O CH2 pre-amplifier output8 VCC Power supply9 VOL( - ) O Loading driver negative output

10 VOL(+) O Loading driver positive output11 VO2( - ) O Driver CH2 negative output12 VO2(+) O Driver CH2 positive output13 VO1( - ) O Driver CH1 negative output14 VO1(+) O Driver CH1 positive output15 VO4(+) O Driver CH4 positive output16 VO4( - ) O Driver CH4 negative output17 VO3(+) O Driver CH3 positive output18 VO3( - ) O Driver CH3 negative output19 GND GND20 BIAS I Bias input21 MUTE Mute control22 OPOUT3 O CH3 pre-amplifier output23 OPIN3(- ) I CH3 pre-amplifier inverted input24 OPIN3(+) I CH3 pre-amplifier input25 OPOUT4 O CH4 pre-amplifier output26 OPIN4(- ) I CH4 pre-amplifier inverted input27 OPIN4(+) I CH4 pre-amplifier input28 REV I Loading driver REV input

BA5985FM

63

DEH-3130R,3100R-B,3100R

CO

MM

ON

SE

GM

EN

T

7.2.2 DISPLAY- CAW1570(DEH-3130R/X1N/EW, DEH-3100R/X1N/EW), CAW1572(DEH-3100R-B/X1N/EW)

64

DEH-3130R,3100R-B,3100R

8. OPERATIONS AND SPECIFICATIONS8.1 OPERATIONS

PTY button

Buttons 1 6

TA/NEWS button

EJECT buttonDisc loading slot

AUDIO button

5//2/3 buttons

FUNCTION button

SOURCE button

+/ button

BAND button

DISPLAY button

DETACH buttonEQ button

65

DEH-3130R,3100R-B,3100R

Basic

Ope

ratio

n

To L

iste

n to

Mus

icTh

e fo

llow

ing

expl

ains

the

initi

al o

f ope

ratio

ns re

quire

d be

fore

you

can

liste

n to

mus

ic.

Not

e:

Load

ing

a di

sc in

this

prod

uct.

1.Se

lect

the d

esire

d so

urce

(e.g.

Tun

er).

Each

pre

ss o

f the

SO

URC

E bu

tton

sele

cts t

he d

esire

d so

urce

in th

e fo

llow

ing

orde

r:B

uilt-

in C

D p

laye

r =Tu

ner

Not

e:

The

soun

d so

urce

will

not

cha

nge

if no

disc

is se

t in

this

prod

uct.

W

hen

this

prod

ucts

blu

e/w

hite

lead

is c

onne

cted

to th

e ca

rs A

uto-

ante

nna

rela

y co

ntro

l ter

min

al,

the

cars

A

uto-

ante

nna

exte

nds w

hen

this

prod

ucts

sourc

e is

switc

hed

ON

. To re

trac

t the

ant

enna

,sw

itch

the

sour

ce O

FF.

2.R

aise

or

low

er th

e vo

lum

e.

3.Tu

rn th

e so

urce

OFF

.

Hol

d fo

r 1 se

cond

Each

pre

ss c

hang

es th

e So

urce

...

Bas

ic O

pera

tion

of T

uner

This

prod

ucts

AF

func

tion

can

be sw

itche

d O

N a

nd O

FF. A

F sh

ould

be

switc

hed

OFF

for

norm

al tu

ning

ope

ratio

ns.

Man

ual a

nd S

eek

Tuni

ng

Yo

u c

an

sel

ect t

he tu

ning

met

hod

by c

hang

ing

the

leng

th o

f tim

e yo

upr

ess

the 2

/3bu

tton.

Man

ual T

unin

g (st

ep by

step

)0.

5 se

cond

s or l

ess

Seek

Tunin

g 0.

5 se

cond

s or m

ore

Not

e:

If yo

u co

ntin

ue p

ress

ing

the

butto

n fo

r lon

ger t

han

0.5

seco

nds,

you

can

skip

bro

adca

stst

atio

ns. S

eek

Tunin

g sta

rts a

s soo

n as

you

rele

ase

the

butto

n.

Ster

eo in

dica

tor

lig

hts w

hen

a ste

reo

statio

n is

sele

cted

. Pres

et N

umbe

r Ind

icat

orB

and

Indi

cato

r

Ban

d FM 1

=FM

2 =

FM 3

=

MW

/LW

Freq

uenc

y In

dica

tor

Pres

et T

unin

g

Yo

u c

an

mem

ori

ze b

roadc

ast s

tatio

ns in

but

tons

1 th

rou

gh 6

for e

asy,

on

e-to

uch

stat

ion

reca

ll.

Pres

et st

atio

n re

call

2 se

cond

s or l

ess

Bro

adca

st sta

tion

pres

et m

emor

y2

seco

nds o

r mor

e

Not

e:

Up

to 1

8 FM

stat

ions

(6 in

FM1,

FM2 a

nd FM

3) an

d 6M

W/L

W st

atio

ns c

an b

e sto

red

in m

emor

y.

You c

an a

lso u

se th

e 5

or

butto

ns to

reca

ll br

oadc

ast

stat

ions

mem

oriz

ed in

but

tons

1 th

roug

h 6.

66

DEH-3130R,3100R-B,3100RBa

sic O

pera

tion

Bas

ic O

pera

tion

of B

uilt-

in C

D P

laye

r

Trac

k Se

arch

and

Fas

t For

war

d/Re

vers

e

Yo

u c

an

sel

ect b

etw

een

Track

Sea

rch

or F

ast F

orw

ard/

Rev

erse

by

pres

sing

the 2

/3bu

tton

for

a di

ffere

nt l

engt

h of

tim

e.

Trac

k Se

arch

0.5

seco

nds o

r les

sFa

st F

orw

ard/

Reve

rse

Cont

inue

pre

ssin

g

Not

e:

If a

disc

can

not b

e in

serte

d fu

lly o

r pla

ybac

k fa

ils, m

ake

sure

the

reco

rded

side

is d

own.

Pre

ss th

eEJ

ECT

butto

n an

d ch

eck

the

disc

for d

amag

e be

fore

rein

serti

ng it

.

If a

CD is

inse

rted

with

the

reco

rded

side

up,

it w

ill b

e eje

cted a

utoma

ticall

y afte

r a fe

w mo

ments

.

If th

e Bu

ilt-in

CD

pla

yer c

anno

t ope

rate

pro

perly

, an

err

or

mes

sage

(suc

h as

ERRO

R-14

) ap

pears

on th

e di

spla

y.

Dis

c Lo

adin

g Sl

ot

Not

e:

The

Built

-in C

D p

laye

r pla

ys o

ne st

anda

rd 1

2 cm

or 8

cm

(sing

le) C

Dat

a ti

me.

Do

not u

se a

n ad

apte

r whe

n pl

ayin

g 8

cm C

D.

Ejec

t Not

e:

The

CDfu

nctio

n ca

n be

turn

edO

N/O

FF w

ith th

e di

sc re

mai

ning

inth

is pr

oduc

t.

A di

sc le

ft pa

rtial

ly in

serte

d af

ter

ejecti

on m

ay in

cur d

amag

e or f

all ou

t.

Play

Tim

e In

dica

tor

Trac

k N

umbe

r Ind

icat

or

Audi

o Ad

justm

ent

Sele

ctin

g th

e Eq

ualiz

er C

urve

You c

an s

witc

h be

twee

n Eq

ualiz

er c

urve

s.

M

ove

the

EQ bu

tton u

p or d

own t

o sele

ct th

e desi

red

Equa

lizer

cur

ve.

POW

ERFU

L +=

NAT

URA

L +=

VO

CAL +=

CUST

OM

+=EQ

FLAT

+=SU

PER

BASS

Not

e:

You c

an c

reat

e di

ffere

nt

CUST

OM

cu

rves

for d

iffer

ent s

ourc

es.

Ente

ring

the

Aud

io M

enu

With

this

Men

u, y

ou c

an a

djust

the so

und q

uality

.

Not

e:

Afte

r ent

erin

g th

e A

udio

Men

u, if

you

do

not p

erfo

rm a

n op

erat

ion

with

in a

bout

30

seco

nds,

the

Aud

io M

enu

is au

tom

atic

ally

can

cele

d.

1.Se

lect

the d

esire

d m

ode

in th

e A

udio

Men

u.

2.O

pera

te a

mod

e.

3.C

ance

l the

Aud

io M

enu.

Each

pre

ss c

hang

es th

e M

ode

...

Equa

lizer

cur

ve

67

DEH-3130R,3100R-B,3100R

Audi

o Ad

justm

ent

Aud

io M

enu

Func

tions

The

Aud

io M

enu

feat

ures

the

follo

win

g fu

nctio

ns.

Bal

ance

Adj

ustm

ent (

FAD

ER)

This

func

tion

allo

ws y

ou to

sele

ct a

Fad

er/B

alan

ce se

tting

that

pro

vide

s ide

al li

steni

ng c

on-

ditio

ns in

all

occu

pied

seat

s.

1.Pr

ess

the

AU

DIO

but

ton

and

sele

ct F

ader

/Bal

ance

mod

e (FA

DER

) in th

eA

udio

Men

u.

Not

e:

FA

DER

: 0

is

the

prop

er se

tting

whe

n 2

spea

kers

are

Documents

Pioneer Deh 3100r Deh 3130r