5
Guida Rapida V1.0 PHANTOM 3 PROFESSIONAL

PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

  • Upload
    others

  • View
    31

  • Download
    0

Embed Size (px)

Citation preview

Page 1: PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

11. Gimbal Dial

12. Camera Settings Dial

13. Video Recording Button

14. Flight Mode Switch

15. Shutter Button

16. Playback Button

17. C1/C2 Buttons (Customizable)

18. USB Port

19. Micro-USB Port

1. Power Button

2. Return to Home (RTH) Button

3. Control Sticks

4. Status LED

5. Battery Level LEDs

6. Power Port

7. Mobile Device Holder

8. Small Device Positioning Tabs

(such as mobile phone)

9. Antennas

10. Handle Bar

Phantom 3 Professional Remote Controller

● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.

2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.

3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.

4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,

radio transmission towers, or Wi-Fi hotspots.

5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when

flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.

6. The Phantom 3 Professional cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning

system will be operational.

● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which

can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal

performance.

1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and

steel reinforcements underground.

2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.

3. DO NOT calibrate beside massive metal objects.

4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after

placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.

Fly Safe Appendix

● P Mode:In this mode, the Phantom 3 Professional can use GPS and the Vision

Positioning system, allowing it to hover accurately in position indoors

and out. When GPS is available, a Home Point will be locked so that the

Phantom 3 Professional can Return to Home if the Remote Controller

signal is lost.

※ This Quick Start Guide is subject to change without prior notice.

Folded

There are three states in P mode:

P-GPS: GPS works best when outdoors and in a wide open area. Your

Phantom 3 Professional uses GPS to hover in place when there is a

strong GPS signal.

P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning

system to hover accurately.

P-ATTI: Neither GPS nor the Vision Positioning system are available.

The aircraft will only use its barometer for altitude and other on-board

sensors for attitude stabilization.

Note that the Vision Positioning system may not work properly when

the Phantom 3 Professional is flying over water, over surfaces without

a clear pattern, or in a low-light environment.

● Return to Home:When there is a strong GPS signal, the aircraft will be able to

record a Home Point and return to that Home Point when

required. The Home Point location is recorded when the GPS

signal icon in the DJI Pilot app is either yellow or green.

The aircraft will return to the Home Point automatically in the

following scenarios (all require a strong GPS signal):

Smart RTH: When the RTH button on the Remote Controller

or in the DJI Pilot app is pressed.

Low-Battery RTH: A notification will appear in the DJI Pilot

app requesting the pilot to take action when the battery level

falls under a certain level.

Failsafe RTH: When the Remote Controller’s signal is lost.

GPS Positioning

Remote Controller

Operating Frequency 2.400 GHz-2.483 GHz

Max. Transmission Distance 2 km (outdoors and unobstructed)

Video Output Port USB

Operating Temperature Range 0°C to 40°C

Battery 6000 mAh LiPo 2S

Mobile Device Holder Tablets and smartphones

Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm

Working Voltage 1.2 A @7.4 V

Charger

Voltage 17.4 V

Rated Power 100 W

Intelligent Flight Battery(PH3-4480 mAh-15.2 V )

Capacity 4480 mAh

Voltage 15.2 V

Battery Type LiPo 4S

Energy 68 Wh

Net Weight 365 g

Operating Temperature -10℃ to 40℃

Max. Charging Power 100 W

FCC ID:SS3-WM3231503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including

interference that may cause undesired operation.

● Aircraft

Weight (Including Battery) 1280 g

Max. Ascent Speed 5 m/s

Max. Descent Speed 3 m/s

Max. Speed 16 m/s (ATTI mode, no wind)

Max. Flight Altitude 6000 m

Max. Flight Time Approximately 23 minutes

Operating Temperature Range 0°C to 40°C

GPS GPS/GLONASS

Gimbal

Angular Vibration Range Pitch: − 90° to +30°

● Vision Positioning

Velocity Range <8 m/s (Altitude 2 m)

Altitude Range 30 cm-300 cm

Operating Range 30 cm-300 cm

Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)

Camera

Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)

Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8

ISO Range 100-3200 (video) 100-1600 (photo)

Electronic Shutter Speed 8 s - 1/8000 s

Image Max. Size 4000 x 3000

Still Photography Modes Single shot

Burst shooting: 3/5/7 frames

Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias

Time-lapse

Video Recording Modes UHD : 4096x2160p 24/25, 3840x2160p 24/25/30

FHD: 1920x1080p 24/25/30/48/50/60

HD: 1280x720p 24/25/30/48/50/60

Max. Bitrate of Video Storage 60 Mbps

Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)

Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required

Operating Temperature Range 0°C to 40°C

It’s time to meet your Phantom 3 Professional.

The Phantom 3 Professional’s camera records video at up to 4K and captures 12 megapixel photos.

Review the diagram below for a full list of your Phantom 3 Professional’s parts:

This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Professional at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.

Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.

* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending

on conditions in your immediate surroundings.

Mobile device connection

DJI encourages you to enjoy flying your Phantom 3 Professional in a safe, responsible, and smart way. To do this, it is important to

understand some basic flight guidelines, both for your protection and for the safety of those around you.

1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above

or near people or animals.

2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to

Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.

3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.

4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)

above ground level, or in line with your local laws and regulations.

Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as

No-Fly Zones.

To enable P Mode, toggle the Flight Mode Switch

to the P position.

10

9

87

3

4

5

1

2

6

14

12

1615

11

17

19 18

13

17

2

7

4

5

9

8

6

3

1

Guida RapidaV1.0

1. Gimbal and Camera

2. Vision Positioning System

3. Camera Micro-SD Card Slot

4. Aircraft Micro-USB Port

5. Front LEDs

6. Motors

7. Propellers

8. Aircraft Status Indicators

9. Antennas

10. Intelligent Flight Battery

11. Power Button

12. Battery Level Indicators

13. Link Button

14. Camera Micro-USB Port

PHANTOM 3PROFESSIONAL

1211

14

10

13

1

8

2

m

m

1

7

2

m

m

105 mm

71 mm

● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote

Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby

buildings to avoid crashing.

Return to home

28

9.5

m

m

28

9 m

m

18

5 m

m

9 feet 10 inches

1 foot

Vision Positioning

Altitude

Page 2: PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

11. Gimbal Dial

12. Camera Settings Dial

13. Video Recording Button

14. Flight Mode Switch

15. Shutter Button

16. Playback Button

17. C1/C2 Buttons (Customizable)

18. USB Port

19. Micro-USB Port

1. Power Button

2. Return to Home (RTH) Button

3. Control Sticks

4. Status LED

5. Battery Level LEDs

6. Power Port

7. Mobile Device Holder

8. Small Device Positioning Tabs

(such as mobile phone)

9. Antennas

10. Handle Bar

Remote Controller

● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.

2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.

3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.

4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,

radio transmission towers, or Wi-Fi hotspots.

5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when

flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.

6. The Phantom 3 Professional cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning

system will be operational.

● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which

can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal

performance.

1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and

steel reinforcements underground.

2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.

3. DO NOT calibrate beside massive metal objects.

4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after

placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.

Fly Safe Appendix

● P Mode:In this mode, the Phantom 3 Professional can use GPS and the Vision

Positioning system, allowing it to hover accurately in position indoors

and out. When GPS is available, a Home Point will be locked so that the

Phantom 3 Professional can Return to Home if the Remote Controller

signal is lost.

※ This Quick Start Guide is subject to change without prior notice.

Folded

There are three states in P mode:

P-GPS: GPS works best when outdoors and in a wide open area. Your

Phantom 3 Professional uses GPS to hover in place when there is a

strong GPS signal.

P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning

system to hover accurately.

P-ATTI: Neither GPS nor the Vision Positioning system are available.

The aircraft will only use its barometer for altitude and other on-board

sensors for attitude stabilization.

Note that the Vision Positioning system may not work properly when

the Phantom 3 Professional is flying over water, over surfaces without

a clear pattern, or in a low-light environment.

● Return to Home:When there is a strong GPS signal, the aircraft will be able to

record a Home Point and return to that Home Point when

required. The Home Point location is recorded when the GPS

signal icon in the DJI Pilot app is either yellow or green.

The aircraft will return to the Home Point automatically in the

following scenarios (all require a strong GPS signal):

Smart RTH: When the RTH button on the Remote Controller

or in the DJI Pilot app is pressed.

Low-Battery RTH: A notification will appear in the DJI Pilot

app requesting the pilot to take action when the battery level

falls under a certain level.

Failsafe RTH: When the Remote Controller’s signal is lost.

GPS Positioning

Remote Controller

Operating Frequency 2.400 GHz-2.483 GHz

Max. Transmission Distance 2 km (outdoors and unobstructed)

Video Output Port USB

Operating Temperature Range 0°C to 40°C

Battery 6000 mAh LiPo 2S

Mobile Device Holder Tablets and smartphones

Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm

Working Voltage 1.2 A @7.4 V

Charger

Voltage 17.4 V

Rated Power 100 W

Intelligent Flight Battery(PH3-4480 mAh-15.2 V )

Capacity 4480 mAh

Voltage 15.2 V

Battery Type LiPo 4S

Energy 68 Wh

Net Weight 365 g

Operating Temperature -10℃ to 40℃

Max. Charging Power 100 W

FCC ID:SS3-WM3231503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including

interference that may cause undesired operation.

● Aircraft

Weight (Including Battery) 1280 g

Max. Ascent Speed 5 m/s

Max. Descent Speed 3 m/s

Max. Speed 16 m/s (ATTI mode, no wind)

Max. Flight Altitude 6000 m

Max. Flight Time Approximately 23 minutes

Operating Temperature Range 0°C to 40°C

GPS GPS/GLONASS

Gimbal

Angular Vibration Range Pitch: − 90° to +30°

● Vision Positioning

Velocity Range <8 m/s (Altitude 2 m)

Altitude Range 30 cm-300 cm

Operating Range 30 cm-300 cm

Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)

Camera

Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)

Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8

ISO Range 100-3200 (video) 100-1600 (photo)

Electronic Shutter Speed 8 s - 1/8000 s

Image Max. Size 4000 x 3000

Still Photography Modes Single shot

Burst shooting: 3/5/7 frames

Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias

Time-lapse

Video Recording Modes UHD : 4096x2160p 24/25, 3840x2160p 24/25/30

FHD: 1920x1080p 24/25/30/48/50/60

HD: 1280x720p 24/25/30/48/50/60

Max. Bitrate of Video Storage 60 Mbps

Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)

Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required

Operating Temperature Range 0°C to 40°C

This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Professional at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.

Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.

* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending

on conditions in your immediate surroundings.

Mobile device connection

DJI encourages you to enjoy flying your Phantom 3 Professional in a safe, responsible, and smart way. To do this, it is important to

understand some basic flight guidelines, both for your protection and for the safety of those around you.

1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above

or near people or animals.

2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to

Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.

3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.

4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)

above ground level, or in line with your local laws and regulations.

Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as

No-Fly Zones.

To enable P Mode, toggle the Flight Mode Switch

to the P position.

10

9

87

3

4

5

1

2

6

14

12

1615

11

17

19 18

13

17

2

7

4

5

9

8

6

3

1

Quick Start GuideV1.0

3PROFESSIONAL

1211

14

10

13

1

8

2

m

m

1

7

2

m

m

105 mm

71 mm

● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote

Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby

buildings to avoid crashing.

Return to home

28

9.5

m

m

28

9 m

m

18

5 m

m

9 feet 10 inches

1 foot

Vision Positioning

Altitude

Phantom 3 Professional

E' il momento di incontrare e conoscere il vostro Phantom 3 Advanced.

La videocamera del Phantom 3 Advanced può restrira video a 1080p/60fps e catturare foto fino a 12 mp.

Vedere lo schema seguente per una lista completa delle parti del vostro Phantom 3 Advanced.

1. Gimbal e videocamera 2. Sistema di posizionamento Vision 3. Scomparto per scheda micro-SD della fotocamera 4. Porta micro-USB velivolo 5. LEDs anteriori 6. Motori 7. Eliche 8. Indicatori di stato del velivolo 9. Antenna10. Batteria intelligente di volo11. Pulsante Power (Accensione/Spegnimento)12. Indicatori livello batteria13. Pulsante collegamento14. Porta micro-USB videocamera

Page 3: PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

Phantom 3 Advanced Telecomando

● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.

2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.

3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.

4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,

radio transmission towers, or Wi-Fi hotspots.

5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when

flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.

6. The Phantom 3 Advanced cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning

system will be operational.

● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which

can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal

performance.

1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and

steel reinforcements underground.

2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.

3. DO NOT calibrate beside massive metal objects.

4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after

placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.

Fly Safe Appendix

● P Mode:In this mode, the Phantom 3 Advanced can use GPS and the Vision

Positioning system, allowing it to hover accurately in position indoors

and out. When GPS is available, a Home Point will be locked so that the

Phantom 3 Advanced can Return to Home if the Remote Controller signal

is lost.

※ This Quick Start Guide is subject to change without prior notice.

There are three states in P mode:

P-GPS: GPS works best when outdoors and in a wide open area.

Your Phantom 3 Advanced uses GPS to hover in place when there is

a strong GPS signal.

P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning

system to hover accurately.

P-ATTI: Neither GPS nor the Vision Positioning system are available.

The aircraft will only use its barometer for altitude and other on-board

sensors for attitude stabilization.

Note that the Vision Positioning system may not work properly when

the Phantom 3 Advanced is flying over water, over surfaces without a

clear pattern, or in a low-light environment.

● Return to Home:

When there is a strong GPS signal, the aircraft will be able to

record a Home Point and return to that Home Point when

required. The Home Point location is recorded when the GPS

signal icon in the DJI Pilot app is either yellow or green.

The aircraft will return to the Home Point automatically in the

following scenarios (all require a strong GPS signal):

Smart RTH: When the RTH button on the Remote Controller

or in the DJI Pilot app is pressed.

Low-Battery RTH: A notification will appear in the DJI Pilot

app requesting the pilot to take action when the battery level

falls under a certain level.

Failsafe RTH: When the Remote Controller’s signal is lost.

● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote

Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby

buildings to avoid crashing.

Remote Controller

Operating Frequency 2.400 GHz-2.483 GHz

Max. Transmission Distance 2 km (outdoors and unobstructed)

Video Output Port USB

Operating Temperature Range 0°C to 40°C

Battery 6000 mAh LiPo 2S

Mobile Device Holder Tablets and smartphones

Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm

Working Voltage 1.2 A @7.4 V

Charger

Voltage 17.4 V

Rated Power 57 W

Intelligent Flight Battery(PH3-4480 mAh-15.2 V )

Capacity 4480 mAh

Voltage 15.2 V

Battery Type LiPo 4S

Energy 68 Wh

Net Weight 365 g

Operating Temperature -10℃ to 40℃

Max. Charging Power 100 W

● Aircraft

Weight (Including Battery) 1280 g

Max. Ascent Speed 5 m/s

Max. Descent Speed 3 m/s

Max. Speed 16 m/s (ATTI mode, no wind)

Max. Flight Altitude 6000 m

Max. Flight Time Approximately 23 minutes

Operating Temperature Range 0°C to 40°C

GPS GPS/GLONASS

Gimbal

Angular Vibration Range Pitch: − 90° to +30°

● Vision Positioning

Velocity Range <8 m/s (Altitude 2 m)

Altitude Range 30 cm-300 cm

Operating Range 30 cm-300 cm

Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)

Camera

Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)

Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8

ISO Range 100-3200 (video) 100-1600 (photo)

Electronic Shutter Speed 8 s - 1/8000 s

Image Max. Size 4000 x 3000

Still Photography Modes Single shot

Burst shooting: 3/5/7 frames

Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias

Time-lapse

Video Recording Modes FHD: 1920x1080p 24/25/30/48/50/60

HD: 1280x720p 24/25/30/48/50/60

Max. Bitrate of Video Storage 60 Mbps

Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)

Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required

Operating Temperature Range 0°C to 40°C

*

DJI encourages you to enjoy flying your Phantom 3 Advanced in a safe, responsible, and smart way. To do this, it is important to

understand some basic flight guidelines, both for your protection and for the safety of those around you.

1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above

or near people or animals.

2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to

Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.

3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.

4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)

above ground level, or in line with your local laws and regulations.

Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as

No-Fly Zones.

To enable P Mode, toggle the Flight Mode Switch

to the P position.

It’s time to meet your Phantom.

The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.

Review the diagram below for a full list of your Phantom 3 Advanced’s parts:

FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including

interference that may cause undesired operation.

PHANTOM 3

Quick Start GuideV1.0

ADVANCED

Return to home

1. Gimbal and Camera

2. Vision Positioning System

3. Camera Micro-SD Card Slot

4. Aircraft Micro-USB Port

5. Front LEDs

6. Motors

7. Propellers

8. Aircraft Status Indicators

9. Antennas

10. Intelligent Flight Battery

11. Power Button

12. Battery Level Indicators

13. Link Button

14. Camera Micro-USB Port

1211

14

10

13

1

8

2

m

m

1

7

2

m

m

105 mm

71 mm

2

7

4

5

9

8

6

3

1

GPS Positioning

28

9.5

m

m

28

9 m

m

18

5 m

m

9 feet 10 inches

1 foot

Vision Positioning

Altitude

11. Regolatore Gimbal

12. Regolatore settaggi videocamera

13. Pulsante registrazione video

14. Selettore modalità di volo

15. Pulsante di scatto

16. Pulsante riproduzione

17. Pulsanti C1/C2 (personalizzabili)

18. Porta USB

19. Porta Micro-USB

1. Pulsante accensione

2. Pulsante di ritorno alla base (RTH)

3. Leve di controllo

4. LED di stato

5. LED indicatore livello batteria

6. Porta alimentazione

7. Supporto dispositivio mobile

8. Linguetta posizionamento dispositivo

9. Antenne

10. Barra di tenuta

Piegato

Connessione dispositivo mobile

10

9

87

3

4

5

1

2

6

14

12

1615

11

17

19 18

13

17

Questo potente telecomando permette di pilotare e manovrare il tuo Phantom 3 Professional a distanze di

oltre 6.000 piedi (2 km) *, tenendo contemporaneamente i controlli della vostra fotocamera a portata di

mano.

Al suo interno vi è una batteria ricaricabile LiPo (polimeri di litio) e il DJI Lightbridge, che se abbinato con un

dispositivo mobile (telefono cellulare o tablet) compatibile vi dà una visione HD in diretta dalla fotocamera del

Phantom.

Questa distanza massima di trasmissione è stata testata in ambiente di laboratorio, ed è solo un riferimento. La distanza operativa massima può variare a seconda delle condizioni nelle vostre immediate vicinanze.

Page 4: PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

Phantom 3 Advanced Remote Controller

● Considerazioni ambientali:

● Calibrazione bussola:

Sicurezza voloAppendix

● P Mode:

※ This Quick Start Guide is subject to change without prior notice.

● Ritorno a casa (RTH):

Remote Controller

Operating Frequency 2.400 GHz-2.483 GHz

Max. Transmission Distance 2 km (outdoors and unobstructed)

Video Output Port USB

Operating Temperature Range 0°C to 40°C

Battery 6000 mAh LiPo 2S

Mobile Device Holder Tablets and smartphones

Transmitter Power (EIRP) FCC: 20 dbm; CE:16 dbm

Working Voltage 1.2 A @7.4 V

Charger

Voltage 17.4 V

Rated Power 57 W

Intelligent Flight Battery(PH3-4480 mAh-15.2 V )

Capacity 4480 mAh

Voltage 15.2 V

Battery Type LiPo 4S

Energy 68 Wh

Net Weight 365 g

Operating Temperature -10℃ to 40℃

Max. Charging Power 100 W

● Aircraft

Weight (Including Battery) 1280 g

Max. Ascent Speed 5 m/s

Max. Descent Speed 3 m/s

Max. Speed 16 m/s (ATTI mode, no wind)

Max. Flight Altitude 6000 m

Max. Flight Time Approximately 23 minutes

Operating Temperature Range 0°C to 40°C

GPS GPS/GLONASS

Gimbal

Angular Vibration Range Pitch: − 90° to +30°

● Vision Positioning

Velocity Range <8 m/s (Altitude 2 m)

Altitude Range 30 cm-300 cm

Operating Range 30 cm-300 cm

Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)

Camera

Sensor Sony EXMOR 1/2.3” Effective pixels:12.4 M (total pixels: 12.76 M)

Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8

ISO Range 100-3200 (video) 100-1600 (photo)

Electronic Shutter Speed 8 s - 1/8000 s

Image Max. Size 4000 x 3000

Still Photography Modes Single shot

Burst shooting: 3/5/7 frames

Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias

Time-lapse

Video Recording Modes FHD: 1920x1080p 24/25/30/48/50/60

HD: 1280x720p 24/25/30/48/50/60

Max. Bitrate of Video Storage 60 Mbps

Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)

Supported SD Card Types Micro-SD, Max. capacity: 64GB. Class 10 or UHS-1 rating required

Operating Temperature Range 0°C to 40°C

This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Advanced at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.

Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.

* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending

on conditions in your immediate surroundings.

It’s time to meet your Phantom.

The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.

Review the diagram below for a full list of your Phantom 3 Advanced’s parts:

FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including

interference that may cause undesired operation.

PHANTOM 3

Quick Start GuideV1.0

ADVANCED

Return to home

1. Gimbal and Camera

2. Vision Positioning System

3. Camera Micro-SD Card Slot

4. Aircraft Micro-USB Port

5. Front LEDs

6. Motors

7. Propellers

8. Aircraft Status Indicators

9. Antennas

10. Intelligent Flight Battery

11. Power Button

12. Battery Level Indicators

13. Link Button

14. Camera Micro-USB Port

1211

14

10

13

1

8

2

m

m

1

7

2

m

m

105 mm

71 mm

2

7

4

5

9

8

6

3

1

GPS Positioning

28

9.5

m

m

28

9 m

m

18

5 m

m

9 feet 10 inches

1 foot

Vision Positioning

Altitude

11. Gimbal Dial

12. Camera Settings Dial

13. Video Recording Button

14. Flight Mode Switch

15. Shutter Button

16. Playback Button

17. C1/C2 Buttons (Customizable)

18. USB Port

19. Micro-USB Port

1. Power Button

2. Return to Home (RTH) Button

3. Control Sticks

4. Status LED

5. Battery Level LEDs

6. Power Port

7. Mobile Device Holder

8. Small Device Positioning Tabs

(such as mobile phone)

9. Antennas

10. Handle Bar

Folded

Mobile device connection

10

9

87

3

4

5

1

2

6

14

12

1615

11

17

19 18

13

17

DJI incoraggia a divertirsi col p roprio Phantom 3 advanced in modo sicuro, responsabile e intelligente. A tal fine è importante capire alcune linee gu ida del volo di base, sia per la vostra protezione che per la sicurezza di chi vi circonda.1. Vola in spazi aperti: Volare sempre in luoghi che sono liberi da edifici, alberi, linee elettriche, e altri ostacoli. Non volare sopra o vicino a persone o animali.

2. Mantenere sempre il controllo: anche quando si uti lizzano le funzioni di autopilota come Auto-Decollo, Auto-atterraggio, e

Auto - Ritorno a casa, tenere sempre le mani sul telecomando e mantenere il controllo del vostro aereo quando è in volo .

3. Mantenere il controllo a vista: mantenete il contatto visivo del vostro velivolo in ogni momento ed evit are di volare dietro gli

edifici o altr i ostacoli che potrebbero ostacolare la vostra visuale.

4. Monitorare la quota: per la sicurezza degli aeromobili di dimensioni standard e del traffico aereo, volare sempre ad altitudini

inferiori a 400 piedi (120 metri sopra il live llo del suolo, o in linea con leggi e normative locali.

Assicurarsi di calibrare la bussola in ogni nuovo luogo in cui si vola. La bussola è molto sensibile

alle interfer fenze elettromagne tiche che potrebbero causare anomalie e scarse prestazioni di

volo o addir ittura il fallimento della missione.

Per ottenere risultati ottimali è necessar ia la calibrazione. Calibrare la bussola quando:

a) L'indicatore di stato del velivolo lampeggia in rosso/g iallo.

b) Quando si vola in una nuova località.

● Non calibrare la bussola, dove c'è possibilità di for ti interferenze magnetiche (magnetite o parcheggi con strutture e rinforzi in

acciaio interrati).

● Non trasportare materiali ferromagnetici con voi durante la calibrazione, come chiavi o telefoni cellulari.

● Non calibrare accanto oggetti metallici voluminosi.

● Se il LED di stato del volo è rosso, prova re a calibrare di nuovo. Se lampeggia rosso/giallo alternativamente dopo

aver piazzato il velivolo a terra, la bussola ha rilevato inter ferenze magnetiche. Cambiare posizione.

1. Non volare in condizioni meteorologiche avverse. Questo include vento forte, neve, pioggia e smog.

2. Volare solo in aree aperte. Edifici alti e strutture in acciaio possono influenzare il segnale della bussola e del GPS.

3. Evitare ostacoli, folle di persone, linee elettriche ad alta tensione, alberi o corpi idrici.

4. Ridurre al minimo interferenze elettromagnetiche e non volare in zone con alti livelli di elettromagnetismo, comprese stazioni

mobili di telefonia o torri di trasmissione radio.

5. Le prestazioni della batteria sono soggette a fattori ambientali (densità e temperatura dell'aria). Fare molta attenzione quando

si vola oltre i 4500 mt slm, in quanto batteria e prestazioni del velivolo putrebbero essere ridotte.

6. A latitudini polari il Phantom 3 advanced non può operare in modalità P e non può utilizzare il GPS. Si può solo volare in moda-

lità ATTI e utilizzare il sistema di posizionamento Vision.

In questa modalità il Phnatom 3 ha un segnale GPS forte e si puòutilizzare il sistema di posizionamento Vision che gli permette di librarsi con precisione sia all'interno che all'esterno.In questa modalità, all'esterno, tramite un Punto Base salvato, il velivolo può tornare indietro in caso di perdita del segnale di controllo.

Per abilitare P Mode, spostare il selettore sulla posizione P.

Ci sono tre stati in modalità P .

P-GPS: il GPS funziona meglio quando si è all'aperto, e il Phantom

lo utilizza per librarsi quando il segnale è forte.

P-OPTI: Se il GPS non è disponibile, il velivolo può utilizzare il

sistema di posizionamento Vision per librarsi in modo accurato.

P-A TTI: Nessun segnale GPS e Vision non disponibile. Il velivolo

utilizza allora solo il suo barometro , controllando solo l'altitudine.

N.B. il sistema di posizionamento Vision potrebbe non funzionare

correttamente quando il Phantom sta volando sull'acqua, su super-

fici senza un motivo chiaro, o in ambienti con scarsa illuminazione.

Se il segnale GPS è forte, il velivolo sarà in grado di registrare

un Punto Base e tornarci in caso di necessità. La posizione

GPS viene registrata quando l'icona del segnale GPS in DJI

App Pilot è gialla o verde. Il Phantom 3 tornerà automatica-

mente alla base nei seguenti casi (è necessario un forte se-

gnale GPS):

RTH intelligente: quando si preme il pulsante RTH sul teleco-

mando.

Batteria scarica RTH: l'applicazione DJI Pilot notifica agli utenti

di agire sull' RTH quando il livello della b atteria scen de ad

una determinata soglia.

Failsafe RTH: Quan do il segnale del telec omando viene perso.

● Durante il ritorno, la quota può essere regolata dall'utente per evitare ostacoli. Edifici alti possono influenzare il segnale deltelecomando. La procedura di ritorno Failsafe si attiva se il segnale si perde. Assicurati volare più in alto rispetto a qualsiasiedificio vicino per evitare collisioni.

Page 5: PHANTOM 3 Phantom 3 Professional Remote Controller Fly ... · Phantom 3 Professionalcan Return to Home if the Remote Controler signalis lost. ※ This Quick Start Guide is subject

Phantom 3 Advanced Remote Controller

● Environmental Considerations:1. Do not fly in severe weather conditions. This includes high winds (speeds of 22 mph or 10 m/s or more), snow, rain, and fog.

2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the on-board compass and GPS signal.

3. Avoid obstacles, crowds, high-voltage power lines, trees, and bodies of water.

4. Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism, including mobile phone base stations,

radio transmission towers, or Wi-Fi hotspots.

5. Aircraft and battery performance are subject to environmental factors such as air density and temperature. Be very careful when

flying 19,600 feet (6 km) or more above sea level, as battery and aircraft performance may not be at peak efficiency.

6. The Phantom 3 Advanced cannot operate in P Mode or use GPS at polar latitudes. Only ATTI Mode and the Vision Positioning

system will be operational.

● Calibrating the Compass:Make sure to calibrate the compass at every new flight location. The compass is very sensitive to electromagnetic interference, which

can cause abnormal compass data, leading to poor flight performance or even failure. Regular calibration is required for optimal

performance.

1. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and

steel reinforcements underground.

2. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.

3. DO NOT calibrate beside massive metal objects.

4. If the Aircraft Status Indicators are showing solid red, then try to calibrate again. If they are blinking red and yellow alternately after

placing the aircraft on the ground, the compass has detected magnetic interference. Change your location.

Fly Safe Appendice

● P Mode:In this mode, the Phantom 3 Advanced can use GPS and the Vision

Positioning system, allowing it to hover accurately in position indoors

and out. When GPS is available, a Home Point will be locked so that the

Phantom 3 Advanced can Return to Home if the Remote Controller signal

is lost.

※ This Quick Start Guide is subject to change without prior notice.

There are three states in P mode:

P-GPS: GPS works best when outdoors and in a wide open area.

Your Phantom 3 Advanced uses GPS to hover in place when there is

a strong GPS signal.

P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning

system to hover accurately.

P-ATTI: Neither GPS nor the Vision Positioning system are available.

The aircraft will only use its barometer for altitude and other on-board

sensors for attitude stabilization.

Note that the Vision Positioning system may not work properly when

the Phantom 3 Advanced is flying over water, over surfaces without a

clear pattern, or in a low-light environment.

● Return to Home:

When there is a strong GPS signal, the aircraft will be able to

record a Home Point and return to that Home Point when

required. The Home Point location is recorded when the GPS

signal icon in the DJI Pilot app is either yellow or green.

The aircraft will return to the Home Point automatically in the

following scenarios (all require a strong GPS signal):

Smart RTH: When the RTH button on the Remote Controller

or in the DJI Pilot app is pressed.

Low-Battery RTH: A notification will appear in the DJI Pilot

app requesting the pilot to take action when the battery level

falls under a certain level.

Failsafe RTH: When the Remote Controller’s signal is lost.

● While returning to the Home Point, the aircraft’s altitude can be adjusted to avoid obstacles. Tall buildings may affect the Remote

Controller’s signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure to fly higher than any nearby

buildings to avoid crashing.

● Velivolo

Peso (incluso batteria) 1280 g

Max. velocità in ascesa 5 m/s

Max. velocità in discesa 3 m/s

● Gimbal

Angular Vibration Range Pitch: − 90° to +30°

● Vision Positioning

Velocity Range <8 m/s (Altitude 2 m)

Altitude Range 30 cm-300 cm

Operating Range 30 cm-300 cm

Operating Environment

This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Advanced at distances over 6,000 feet (2 km)* away, while putting selected camera controls at your fingertips.

Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera.

* This maximum transmission distance was tested in a lab environment and is for reference only. The maximum operating distance may vary depending

on conditions in your immediate surroundings.

DJI encourages you to enjoy flying your Phantom 3 Advanced in a safe, responsible, and smart way. To do this, it is important to

understand some basic flight guidelines, both for your protection and for the safety of those around you.

1. Fly in Open Areas: Always fly in locations that are free and clear of buildings, trees, power lines, and other obstacles. Do not fly above

or near people or animals.

2. Maintain Control at All Times: Even when using DJI autopilot functions such as Auto-Takeoff, Auto-Landing, and Auto-Return to

Home, always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight.

3. Maintain Line of Sight: Keep your aircraft in sight at all times, and avoid flying behind buildings or other obstacles that may block your view.

4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always fly at altitudes less than 400 feet (120 meters)

above ground level, or in line with your local laws and regulations.

Visit http://flysafe.dji.com/no-fly for more information on critical safety features such as

No-Fly Zones.

To enable P Mode, toggle the Flight Mode Switch

to the P position.

It’s time to meet your Phantom.

The Phantom 3 Advanced’s camera records video at up to 1080p/60fps and captures 12 megapixel photos.

Review the diagram below for a full list of your Phantom 3 Advanced’s parts:

FCC ID:SS3-WM3221503 FCC ID: SS3-GL3001501This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including

interference that may cause undesired operation.

PHANTOM 3

Quick Start GuideV1.0

ADVANCED

Return to home

1. Gimbal and Camera

2. Vision Positioning System

3. Camera Micro-SD Card Slot

4. Aircraft Micro-USB Port

5. Front LEDs

6. Motors

7. Propellers

8. Aircraft Status Indicators

9. Antennas

10. Intelligent Flight Battery

11. Power Button

12. Battery Level Indicators

13. Link Button

14. Camera Micro-USB Port

1211

14

10

13

182 mm

172 mm

105 mm

71 mm

2

7

4

5

9

8

6

3

1

GPS Positioning

28

9.5 mm

289 mm

18

5 m

m

9 feet 10 inches

1 foot

Vision Positioning

Altitude

11. Gimbal Dial

12. Camera Settings Dial

13. Video Recording Button

14. Flight Mode Switch

15. Shutter Button

16. Playback Button

17. C1/C2 Buttons (Customizable)

18. USB Port

19. Micro-USB Port

1. Power Button

2. Return to Home (RTH) Button

3. Control Sticks

4. Status LED

5. Battery Level LEDs

6. Power Port

7. Mobile Device Holder

8. Small Device Positioning Tabs

(such as mobile phone)

9. Antennas

10. Handle Bar

Folded

Mobile device connection

10

9

87

3

4

5

1

2

6

14

12

1615

11

17

19 18

13

17

Gamma angolo d'inclinazione: -90° a +30°

Posizionamento VisionGamma velocità: <8m/s (altitudine 2 m)Gamma altitudine: 30 cm - 300cmGamma operativa: 30 cm - 300 cmSuperfice operativa: superficie con motivo pulito e adeguata illuminazione

Gimbal

Camera

Velivolo

Peso (incluso batteria) 1280gVelocità max in ascesa 5 m/sVelocità max in discesa 3 m/s

Velocità max assoluta 16 m/s (mode ATTI, senza vento)Max altezza di volo 6000 m.Tempo max di volo approssimativo 23 minutiGamma temperatura operativa da 0° a 40° C

Sensore Sony EXMOR 1/2.3" Pixel effettivi 12.4 M (Totali 12,76 m)

Lenti FOV (campo visivo) 94° 20mm (equivalente a formato 35mm) f2/8Gamma ISO 100-3200 (video) 100-1600 (foto)

Velocità scatto elettronico 8s - 1/8000sMisura max immagine 4000 x 3000

Modalità di scatto: Scatto singo loScatto a raffica: 3/5/7 fotogrammiAuto-Esposizione (Bracketing AEB): 3/5 fotogrammi a 0.7EV BiasTime-lapse

Modalità registrazione video UHD 4096x2160p 24/25, 3840x2160p, 24/25/30 FHD : 1920x1080p 24/25/30/48/50/60

HD : 1280x720p 24/25/30/48/50/60

Max bitrate memorizzazione video : 60 MbpsFile supportati: file FAT32/exTAF - foto JPEG, DNG - video MP4/MOV (MPEG-4 AVC/H.264)SD CARD supportate: Micro-SD, capacità max 64GB - richiesta classe 10 o UHS-1Temperatura operativa da 0° a 40° C

(Lux> 15)

Telecomando

Frequenza operativa 2.400 GHz-2.483GHzDistanza massima di trasmissione 2 km (all'esterno senza ostacoli)Uscita video: porta USBTemperatura operativa da 0° a 40° CBatteria 6000 mAh LiPo 2SSupporto per dispositivi mobili (tablets e smartphones)Potenza trasmissione (EIRP) FCC: 20dbm CE: 16dbmTensione di funzionamento: 1.2 A @ 7.4V

Caricatore

Tensione 17.4VPotenza nominale 100W

Batteria intelligente di volo (PH3-4480 mAh-15.2V)

Capacità 4480 mAhTensione 15.2VTipo batteria LiPo 4SEnergia 68WhPeso netto 365gTemperatura operativa da -10° a 40° CPotenza massima di carica 100W

GPS GPS/GLOMASS