PEUGEOT EXPERT TEPEE (2007 - 2011) MKi + CK (EN_US).pdf

207 EXPERT TEPEE

This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.

EXPERT TEPEE

Installation manual: Parrot MKi + Parrot CK3100 range

The brand name PEUGEOT EXPERT TEPEE and the PEUGEOT logo are the property of AUTOMOBILES PEUGEOT. This document is only valid for the vehicle model EXPERT TEPEE® year 2007 to 2011, excluding all other models in the same range and excluding later modifications made to the vehicle by the manufacturer. The Parrot brand name and logos are the exclusive property of Parrot SA.

207 EXPERT TEPEE


Accessories required

Disassembly 15min

Kit installation 15min

Refitting 15min

Testing 15min

Total 1 hour

NO ACC wire

YES ISO

N/A UNIKA

FRONT SPEAKER TEL mode

ALL MUSIC mode

Fitting time (estimated) / Main features

Tools

- Multimeter or Test lamp

- Hose clamp

- Electrical tape

"Please contact your Wholesaler to purchase accessories."

Updating

Plastic trim removal tools FACOM / BERNER

FACOM Sleeve DX-25 (n°4 spanners)

Kram ref. Dealer ref.

CK range N/A 9706 AR

MKi range N/A 9706 AR

To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at

www.parrot.com/usa/support/downloads

http://www.parrot.com/uk/support/downloads

207 EXPERT TEPEE


Disassembly

207 EXPERT TEPEE


Disassembly 1 / 2

Insert the removal tools into the slots on each side of the radio.

Unclip, pull and remove the radio taking care to unplug

the connector and the antenna.

1 2

Using a plastic trim tool, unclip the screen surround on the top of the

dashboard starting from the bottom.

Using a plastic trim tool, unclip and half open the air vent

surround from the top.

3 4

5 6

Using a plastic trim tool, unclip the panel under the steering wheel

starting from the bottom.

Remove screws 1 and 2, then unclip and half open the panel under the

steering wheel.

1

2

207 EXPERT TEPEE


Disassembly 2 / 2

Remove the door seal on the driver’s side.

7

207 EXPERT TEPEE


Microphone passage

Stick the microphone bracket (supplied) to the windscreen after thoroughly cleaning the surface. Then run the cable

under the headliner towards the driver's side door.

Run the cable replacing the seal on the driver's side door.

1 2

Then run it under the dashboard towards the radio, attaching it with

wire ties.

3

207 EXPERT TEPEE


Finding an ACC wire

Unclip the DIAG socket and pull it out from behind, towards the

top of the panel under the steering wheel.

Find position 1 using a multimeter, check the presence

of +12V after ignition.

1 2

10

3

On the corresponding white wire, make a pigtail connection. Or use a jumper to connect a

wire.

3 4

3

Pass it towards the radio housing.

Swap the RED and ORANGE fuses. Cut the red wire between the fuse and the ISO connector.

Connect the ACC wire.

5 6

207 EXPERT TEPEE


Feeding the accessory cable

Using a guide, feed the cable into the hole towards the car stereo

housing.

Then place the cable being careful to leave enough length.

1 2

207 EXPERT TEPEE


Fitting the hands-free system 1 / 2

Connect all the factory cables (supplied) or with the 9706AR CK/Mki manufacturer to the blue box as shown in the diagram below. Test the assembly before reassembly, then slide the

assembly down to the back of the radio housing.

1

ISO adapter

207 EXPERT TEPEE


Fitting the hands-free system 2 / 2

Feed the cable through the left side of the centre console

surround. (To do this lift it up using a plastic trim tool towards

the radio.)

Clip the centre console and the display surround back on. (Make

sure that you DO NOT cut the cable.) Then stick the bracket to

the screen (supplied) after having cleaned the surface.

2 3

!

207 EXPERT TEPEE


Testing

Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob

of the remote control, check:

1 - That the menu is displayed on the screen. (Language or iPod.) 2 - That the system can be muted. (Click in the blue box) 3 - That there is no sound coming from the speakers. 4 - That the sound from the voice menu is coming out of the front speakers. 5 - Then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen. (If this fails, reverse the fuses on the kit's wiring harness.) 6 - Pair a telephone with the kit to make a call. (Check that both the microphone and the kit are working.)

207 EXPERT TEPEE


Reassembly

Refit the system using the following procedure: 1 - Slide the radio back in, then reconnect the ISO and the antenna. (Be careful with the screen cable.) 2 - Clip the DIAG socket back on. 3 - Clip the panel under the steering wheel back on and replace screws 1 and 2. 4 - Clip the fuse box cover back on under the steering wheel.

Documents

PEUGEOT EXPERT TEPEE (2007 - 2011) MKi + CK (EN_US).pdf