Performance Additives and Resins for Solvent-based …elementis-specialties-asia.com/esweb_new/webprodliterature.nsf... · Performance Additives and Resins ... automotive coatings

Performance Additives and Resins for Solvent-based Systems

2

Organoclays 10

Organic Rheological Additives 12

Chemical Activators 14

Defoamers 16

Wetting and Dispersing Agents 16

Leveling Agents 20

Interfacial Tension Modifiers 22

Adhesion Promoters 22

Speciality Additives 22

Surface Modifiers 24

Resins 24

3

BENTONE®, BENGEL® and BENTONE

SD® organoclay rheological additives are

reaction products of highly purified smectite

clay (bentonite or hectorite) and a quaternary

ammonium salt. When properly selected and

activated, they will increase low shear viscosity,

reduce sagging and help reduce settling in

solvent-based formulations. These 100% active

rheological additives are not temperature

sensitive and can be activated using polar

compounds such as methanol, ethanol or

propylene carbonate or chemical activators

such as DAPRO® FX 2060 or DAPRO® BEZ 75.

THIXATROL® and THIXCIN® rheological

additives are based on castor oil derivatives,

polyamide or polyester amide chemistry. They

typically must be subjected to appropriate

wetting, dispersion forces and minimum

temperature requirements to reach an activated

structure.

THIXATROL® MAX and THIXATROL® P200X

are effective in all solvents, provide excellent

sag control, are seed resistant and have a

broad activation temperature window.

In MS-Polymer sealants THIXATROL® MAX

also provides excellent rheology at low

activation temperatures.

M-P-A® anti-settling agents inhibit pigments

and extenders movement in the paint. In most

formulations, settling problem will largely be

eliminated. These products function by chain

entanglement and can be used alone or in

combination with a thixotropic additive for

enhanced performance.

Product selection is typically dependent on

the solvent and reactivity of the system to be

modified.

Rheological Additives

Fig.1 Enlargement of activated organoclay

4

Dispersion of pigments can be generally

divided into three stages.

1. Wetting

Wetting is a process in which air and moisture

on the pigment surface are replaced by wetting

dispersants (as shown in fig 2).

Wetting dispersants can significantly reduce

pigment surface tension, speed up pigment

wetting, and lower the viscosity of pigment

pastes.

Fig. 2 Wetting on pigment surface

2. Dispersion

High-speed or high shear dispersing equipment

is used to disperse pigment aggregates thereby

producing discrete primary particles which

enable optimum flow, color, opacity and optical

properties (as shown in Fig. 3).

Fig. 3 Pigment dispersion

3. Stabilization

A wetting dispersant, through its steric effect

or electrostatic repulsion, keeps the dispersed

and disaggregated pigment particles apart and

effectively prevents their re-flocculation (as

shown in Fig.4).

Fig. 4 Pigment stabilization

Wetting and dispersing properties of pigments

are usually associated with their shape,

size, surface area, oil absorption capacity,

surface treatment, acidity and alkalinity, and

is also closely related to the polarity, surface

tension and viscosity of the paint system. The

advantages of NUOSPERSE® and Disponer

wetting dispersants are:

Add Wetting Agent

Mill

Flocculation

Add Dispersing Agent

Wetting and Dispersing Agents

5

Rapid wetting of the pigment surface to

improve grinding efficiency

Excellent viscosity reduction and

dispersion performance

Good flow of mill base at high pigment

loading

Excellent tinting strength and color

development

Improved flooding, floating and color

rub up issues

Long-term viscosity stability

Excellent initial gloss and gloss

retention

Elimination of hard settling

NUOSPERSE® AP 657 is a versatile wetting,

dispersing and stabilizing aid for non-aqueous

systems. It is compatible with a broad range of

air drying resin systems as well as plasticizers.

It has a very low aromatic content.

NUOSPERSE® FA 196 is a 100 % active

dispersing agent for a wide range of pigments

and is especially recommended for carbon

black. It is effective in reducing rub-up and

preventing pigment flooding and floating. This

solvent free dispersant is excellent for high

performance, low VOC and VOC-free coating

formulations.

NUOSPERSE® FA 601 improves opacity,

gloss, colour strength, brightness and is very

cost efficient.

NUOSPERSE® 2008 is a solvent-free, low

odour, wetting and dispersing agent. The

product is typically used in high solids, alkyd

coatings to improve opacity, gloss and colour

strength.

NUOSPERSE® FX 9086 is a 50 % active

polymeric dispersing agent for a wide range

of pigments. It is universal in application and

can be used in formulating high performance

coatings and colorants.

NUOSPERSE® 9100 is a 100 % active,

solvent-free acrylic based pigment dispersing

polymer in powder form. It can be used as the

sole dispersing agent for solvent free, radiation

cured and high solids coatings systems.

NUOSPERSE® 15 is a liquid version of

NUOSPERSE® 9100 with 65% active content.

NUOSPERSE® FX 9200 and NUOSPERSE®

FX 9360 are newly developed hyperdispersants

for use in industrial, automotive coatings and

inks (including UV) applications. Based on

high molecular weight polymers with multiple

pigment affinic groups, they provide exceptional

pigment wetting and dispersing efficiency

thereby allowing high pigment loading with full

color strength development in short dispersion

times.

Disponer 9250 is a highly versatile dispersant

for all types of TiO2 resulting in coatings with

enhanced storage stability and good color

acceptance and compatibility when tinted with

colorants.

Disponer 983 and Disponer 9850 are polymeric

dispersing agents that are highly effective

for dispersing carbon black and organic

pigments. They are used in a wide range of high

performance solvent-based industrial coatings.

6

DAPRO® and Defom defoamers are grouped

into silicone and silicone-free categories.

The broad product line offers a multitude of

solutions in combating foam generated during

the manufacturing and application processes of

solvent-based coatings.

DAPRO® AP 1622 is a highly effective silicone

defoamer used in oil and alkyd modified

urethanes, nitrocellulose lacquers, chlorinated

rubber and epoxies.

DAPRO® DF MOM and Defom 3500 are

recommended for air-drying alkyd systems,

alkyd-melamine baking enamels, acrylic

isocyanate lacquers, nitrocellulose lacquers,

acid-curing lacquers and epoxy primers.

Defom 5300 is a general purpose silicone

defoamer that provides excellent defoaming

and compatibility in industrial solvent-based

coatings.

Defom 5800F is an aromatic-free, general

purpose defoamer for industrial solvent-based

coatings. It shows good system compatibility in

various coating systems.

Defom 6800 is a 100% active, aggressive foam-

release and anti-foaming agent particularly

suited for epoxy floor coatings, epoxy floorings

and other high-build systems.

DefoamersLevaslip and Levelol leveling agents and

DAPRO® interfacial tension modifiers improve

surface slip, leveling and reduce film defects

such as crawling, fisheyes, cratering, orange

peel and Benard cells. They also promote

spreading and uniform film formation on hard to

wet or contaminated surfaces. These additives

are also effective in overcoming color floating

and flooding issues commonly found in solvent-

based coatings.

Leveling agents and slip additives quickly

migrate to the coating surface to reduce the

surface tension of the drying film. They help to

level and eliminate the development of Benard

cells by providing a uniform surface. In addition,

the structure of the modified polysiloxane

provides a low coefficient of friction on the

coating surface after drying and enhances

the surface smoothness, slip and anti-scratch

properties.

Levaslip Polysiloxane leveling agents

are derived from a polydimethylsiloxane

(Fig. 5). Modification of polydimethylsiloxane

with polyether is done on pendant methyl

groups to improve its compatibility and vary

its surface tension. The polyether typically

contains ethylene oxide (EO) and/or propylene

oxide (PO) chains (Fig. 6).

Leveling Agents

7

By adjusting the ratio of hydrophilic (EO) and

lipophilic (PO) groups, polarity of the additives

can be controlled to provide good compatibility

in high/low polarity coating systems. This in turn

influences the leveling and foaming behaviors

of the additives. Modified polysiloxanes are

particularly effective in minimizing orange peel

caused by short wave.

Fig. 5 Polydimethylsiloxane

Fig. 6 Polyether modified polydimethylsiloxane

Silicone-based leveling agents can migrate to the

coating surface and negatively affect recoatability

of dried film. Where the use of polysiloxane leveling

agents is not recommended, Levelol polyacrylate

leveling agents are the best alternative for

systems requiring recoatability such as primers.

They not only enhance film smoothness, but also

promote leveling speed and substrate wetting. For

enhanced performance, fluorocarbon-modified

products such as Levelol 837 and Levelol 839 are

recommended.

(C H ) S i O S i O S i(C H )3 3 3 3

C H 3

C H 3 M

?Ï€@»E€G¥Ò°òÖº®ñÖJ

( C H ) S i O S i O S i O S i( C H )3 3 3 3

C H 3

C H 3 M

C H 3

( C H ) m2

O C H C H O R22

R 1

nN

?Ï€G»EîÅ§ï©Ê»E€G¥Ò°òÖº®ñÖJ

E O R = H§ï©Ê¡G 1 P O R = C H§ï©Ê¡G 13

EO Modification：R1 =H PO Modification：R1 = CH3

DAPRO® Interfacial Tension Modifiers

These products are designed to eliminate or

reduce coating defects, such as orange peel,

fish eyes and cratering. They also improve

leveling of paint films. DAPRO® interfacial

tension modifiers have excellent recoatability.

DAPRO® S-65 is generally effective in high

solids and conventional polyesters and acrylics.

whereas DAPRO® U-99 is generally more

effective in two-component epoxies and alkyds.

The latter can also be used in water based

systems.

8

Surface ModifiersSLIP-AYD® additives are based on low

molecular weight polyethylene and other

synthetic and natural waxes. They reduce the

coefficient of friction and increase apparent film

hardness of coatings.

SLIP-AYD® waxes can protect a coating from:

Marring, scuffing

Blocking扰

Staining

Rubbing

Metal Marking

Water Penetration

Abrasion

Scratching

Forming Damage

Transit Damage

SLIP-AYD® dispersions include polyethylenes,

hard polymeric and carnauba waxes dispersed

in a variety of solvents or solvent blends. These

dispersions are stable and will not recrystallize,

gel, or settle on storage. The solvents and

vehicles have been selected for optimum

performance in the widest range of coating

systems. The degree of dispersion has been

carefully controlled for reproducible results.

Many waxes can be effective in improving

the surface characteristics of the coatings or

eliminating performance problems associated

with coefficient of friction. Effectiveness is

dependent on several factors including, but

not limited to, wax chemistry, hardness, and

softening range. Experience has shown that

certain wax types provide consistent results in

a wide range of applications.

Polyethylene

Low molecular weight polyethylenes offer good

resistance to abrasion, blocking, marring and

scuffing. They are very versatile with good

overall results and benefits.

High melt polyethylene

Extremely hard, low molecular weight

polyethylenes offer exceptional resistance to

blocking and abrasion. May reduce gloss.

Hard polymeric wax (Fischer-Tropsch)

Hard, brittle, synthetic aliphatic wax that provides

excellent slip and good block resistance.

9

Carnauba wax

A hard, brittle, lustrous natural wax which

provides very low coefficient of friction, excellent

product release and improved resistance to

marring, scuffing and metal marking.

Soft polymeric wax

A tough plastic synthetic wax which provides

exceptional slip and excellent mar resistance.

Wax blends

Blends of synthetic waxes and wax-like materials

that synergistically enhance the benefits of the

individual waxes. They are highly effective in

reducing coefficient of friction and increasing

the resistance to marring, scuffing, and rubbing.

PTFE

Ultra low coefficient of friction and exceptional

resistance to high temperature. Easy to blend

withother waxes for best value and property

balance.

Polysiloxane

Provides increased slip and mar resistance.

10

Product Composition Form Active % Chemical Activator Shear Energy Principal Use Use Level % Product

BENATHIX® Organically modified smectite clay Powder 100 Not required Medium Suitable for medium-to-high polarity solvent-based coatings, inks and unsaturated polyester gel coats

0.5 - 1.0 BENATHIX®

BENGEL® 434 Organic derivative of a bentonite clay Powder 100 Recommended High Low polarity aliphatic and aromatic systems 0.3 - 1.2 BENGEL® 434

BENGEL® 658 Organic derivative of a bentonite clay Powder 100 Not required High Low polarity aliphatic and aromatic systems 0.2 - 1.5 BENGEL® 658

BENGEL® 938 organic derivative of a bentonite clay Powder 100 Recommended High medium polarity aliphatic and aromatic systems 0.2 - 2.0 BENGEL® 938


BENGEL® 828 Organic derivative of a bentonite clay Powder 100 Not required High High polarity aromatic and oxygenated systems 0.2 - 2.0 BENGEL® 828

BENGEL® 858 Organic derivative of a bentonite clay Powder 100 Recommended High Medium polarity aliphatic and aromatic systems 0.2 - 2.0 BENGEL® 858



BENGEL® 988 Organic derivative of a bentonite clay Powder 100 Not required Medium Suitable for medium-to-high polarity solvent-based coatings & inks 0.2 - 2.0 BENGEL® 988

BENTONE® 27 Organic derivative of a hectorite clay Powder 100 Recommended High High polarity aromatic and oxygenated systems 0.2 - 1.0 BENTONE® 27

BENTONE® 38 Organic derivative of a hectorite clay Powder 100 Recommended High Medium polarity aliphatic and aromatic systems 0.2 - 1.0 BENTONE® 38

BENTONE® 34 Organic derivative of a bentonite clay Powder 100 Recommended High Low polarity aliphatic and aromatic systems 0.2 - 3.0 BENTONE® 34

BENTONE® 52 Organic derivative of a bentonite clay Powder 100 Recommended High Low-medium polarity aliphatic and aromatic systems 0.5 - 1.0 BENTONE® 52

BENTONE® 54 Organic derivative of a bentonite clay Powder 100 Recommended High Low-medium polarity aliphatic and aromatic system 0.2 - 1.0 BENTONE® 54

BENTONE® 57 Organic derivative of a bentonite clay Powder 100 Recommended High Medium-high polarity aromatic and oxygenated systems 0.4 - 2.0 BENTONE® 57

BENTONE® 1000 Organic derivative of a bentonite clay Powder 100 Beneficial High Low polarity aliphatic and aromatic systems 0.2 - 2.0 BENTONE® 1000

BENTONE SD® -1 Organic derivative of a bentonite clay Powder 100 Not required Medium Low polarity aliphatic and aromatic systems 0.2 - 2.0 BENTONE SD® -1

BENTONE SD® -2 Organic derivative of a bentonite clay Powder 100 Not required Medium High polarity aromatic and oxygenated systems 0.2 - 2.0 BENTONE SD® -2

BENTONE SD® -3 Organic derivative of a smectite clay Powder 100 Not required Medium Medium polarity aliphatic and aromatic systems 0.2 - 1.0 BENTONE SD® -3

Organoclays

11

Product Composition Form Active % Chemical Activator Shear Energy Principal Use Use Level % Product

BENATHIX® Organically modified smectite clay Powder 100 Not required Medium Suitable for medium-to-high polarity solvent-based coatings, inks and unsaturated polyester gel coats

0.5 - 1.0 BENATHIX®



BENGEL® 938 organic derivative of a bentonite clay Powder 100 Recommended High medium polarity aliphatic and aromatic systems 0.2 - 2.0 BENGEL® 938


BENGEL® 828 Organic derivative of a bentonite clay Powder 100 Not required High High polarity aromatic and oxygenated systems 0.2 - 2.0 BENGEL® 828

BENGEL® 858 Organic derivative of a bentonite clay Powder 100 Recommended High Medium polarity aliphatic and aromatic systems 0.2 - 2.0 BENGEL® 858



BENGEL® 988 Organic derivative of a bentonite clay Powder 100 Not required Medium Suitable for medium-to-high polarity solvent-based coatings & inks 0.2 - 2.0 BENGEL® 988

BENTONE® 27 Organic derivative of a hectorite clay Powder 100 Recommended High High polarity aromatic and oxygenated systems 0.2 - 1.0 BENTONE® 27

BENTONE® 38 Organic derivative of a hectorite clay Powder 100 Recommended High Medium polarity aliphatic and aromatic systems 0.2 - 1.0 BENTONE® 38

BENTONE® 34 Organic derivative of a bentonite clay Powder 100 Recommended High Low polarity aliphatic and aromatic systems 0.2 - 3.0 BENTONE® 34

BENTONE® 52 Organic derivative of a bentonite clay Powder 100 Recommended High Low-medium polarity aliphatic and aromatic systems 0.5 - 1.0 BENTONE® 52

BENTONE® 54 Organic derivative of a bentonite clay Powder 100 Recommended High Low-medium polarity aliphatic and aromatic system 0.2 - 1.0 BENTONE® 54

BENTONE® 57 Organic derivative of a bentonite clay Powder 100 Recommended High Medium-high polarity aromatic and oxygenated systems 0.4 - 2.0 BENTONE® 57

BENTONE® 1000 Organic derivative of a bentonite clay Powder 100 Beneficial High Low polarity aliphatic and aromatic systems 0.2 - 2.0 BENTONE® 1000

BENTONE SD® -1 Organic derivative of a bentonite clay Powder 100 Not required Medium Low polarity aliphatic and aromatic systems 0.2 - 2.0 BENTONE SD® -1

BENTONE SD® -2 Organic derivative of a bentonite clay Powder 100 Not required Medium High polarity aromatic and oxygenated systems 0.2 - 2.0 BENTONE SD® -2

BENTONE SD® -3 Organic derivative of a smectite clay Powder 100 Not required Medium Medium polarity aliphatic and aromatic systems 0.2 - 1.0 BENTONE SD® -3

12

Product Composition Solvent Form Active % Activator Principal Use Use Level % Product

THIXATROL® MAX Proprietary organic None Powder 100 Temperature control and high shear forces

Low-high polarity systems 0.2 - 2.0 THIXATROL® MAX

THIXATROL® PLUS Proprietary organic None Powder 100 Temperature control and high shear forces

Conventional and High build industrial coatings 0.2 - 0.5 THIXATROL® PLUS

THIXATROL® AS 8053 Proprietary organic None Powder 100 Temperature control and dwell time requirements

Hybrid sealants, industrial coatings, epoxy primers and polyurethane top coat systems

0.5 - 3.5 THIXATROL® AS 8053

THIXATROL® P600 Polyamide wax None Powder 100 Temperature control and high shear forces

Heavy duty coatings, epoxy paint, chlorinated rubber, alkyd paint

1.0 - 3.0 THIXATROL® P600

THIXATROL® P200N Special polyamide wax Aliphatic solvent Paste 19 - 21 Suitable for post-add Solvent-based coatings, ink systems, sealants 1.0 - 5.0 THIXATROL® P200N

THIXATROL® P220X Special polyamide wax Xylene/alcohols Paste 19 - 21 Suitable for post-add Solvent-based coatings, ink systems, sealants 1.0 - 5.0 THIXATROL® P220X

THIXATROL® P220XF Special polyamide wax BTX-free solvent Paste 19 - 21 Suitable for post-add Solvent-based coatings, ink systems, sealants 1.0 - 5.0 THIXATROL® P220XF



THIXATROL® ST Modified castor oil derivative None Powder 100 Temperature control and high shear forces

Low polarity aliphatic and aromatic systems 0.2 - 1.0 THIXATROL® ST

THIXATROL® UV1104 Polyester None Liquid 100 Temperature and shear forces High solids or 100 % NV pigmented UV systems 0.2 - 1.0 THIXATROL® UV1104

THIXCIN® R Organic derivative of castor oil None Powder 100 Temperature control and high shear forces

Low polarity aliphatic systems 0.2 - 0.8 THIXCIN® R

M-P-A® 10X Complex polyolefin compound Xylene Liquid 9 - 11 Temperature control and high shear forces

Prevent pigment settling, especially for metallic paint

2.0 - 5.0 M-P-A® 10X

M-P-A® 20X Complex polyolefin compound Xylene Paste 19 - 21 Temperature control and high shear forces

Anti-settling for pigment, metallic and pearlescent paint in solvent-based coatings

0.5 - 2.0 M-P-A® 20X

M-P-A® 60X Organic compound Xylene Paste 22 - 26 Temperature and high shear forces Medium-high polarity aromatic and oxygenated systems

1.0 - 3.0 M-P-A® 60X

M-P-A® 1078 X Organic compound Xylene Paste 39 - 41 Temperature and high shear forces Industrial coatings, traffic paint, marine coatings 0.2 - 1.0 M-P-A® 1078 X

M-P-A® 2000 X Proprietary organic compound Xylene Pourable liquid

20 Temperature and high shear forces Medium-high polarity aromatic and oxygenated systems

0.5 - 1.5 M-P-A® 2000 X



0.5 - 1.5 M-P-A® 4020 X

M-P-A® 4020BA Proprietary organic compound Butyl acetate Pourable liquid

20 Temperature and high hear forces Medium-high polarity aromatic and oxygenated HAPS free systems

0.5 - 1.5 M-P-A® 4020BA

DeuRheo 209 Polyamide wax Xylene/alcohols Paste 19 - 21 Temperature and shear forces Solvent-based coatings, ink, anti-corrosion primer, sealant

0.1 - 5.0 DeuRheo 209

DeuRheo 219 Polyamide wax Xylene/alcohols Paste 19 - 21 Temperature and shear forces Metallic, pearlescent, matte coatings 1.0 - 5.0 DeuRheo 219

DeuRheo 2810 Modified polyurea N-methyl pyrrolidone Liquid 50 - 54 Temperature and shear forces Medium polarity systems like epoxy coatings, polyurethane coatings

0.5 - 3.0 DeuRheo 2810

Organic Rheological Additives

13


THIXATROL® MAX Proprietary organic None Powder 100 Temperature control and high shear forces

Low-high polarity systems 0.2 - 2.0 THIXATROL® MAX

THIXATROL® PLUS Proprietary organic None Powder 100 Temperature control and high shear forces

Conventional and High build industrial coatings 0.2 - 0.5 THIXATROL® PLUS

THIXATROL® AS 8053 Proprietary organic None Powder 100 Temperature control and dwell time requirements

Hybrid sealants, industrial coatings, epoxy primers and polyurethane top coat systems

0.5 - 3.5 THIXATROL® AS 8053

THIXATROL® P600 Polyamide wax None Powder 100 Temperature control and high shear forces

Heavy duty coatings, epoxy paint, chlorinated rubber, alkyd paint

1.0 - 3.0 THIXATROL® P600

THIXATROL® P200N Special polyamide wax Aliphatic solvent Paste 19 - 21 Suitable for post-add Solvent-based coatings, ink systems, sealants 1.0 - 5.0 THIXATROL® P200N


THIXATROL® P220XF Special polyamide wax BTX-free solvent Paste 19 - 21 Suitable for post-add Solvent-based coatings, ink systems, sealants 1.0 - 5.0 THIXATROL® P220XF



THIXATROL® ST Modified castor oil derivative None Powder 100 Temperature control and high shear forces

Low polarity aliphatic and aromatic systems 0.2 - 1.0 THIXATROL® ST

THIXATROL® UV1104 Polyester None Liquid 100 Temperature and shear forces High solids or 100 % NV pigmented UV systems 0.2 - 1.0 THIXATROL® UV1104

THIXCIN® R Organic derivative of castor oil None Powder 100 Temperature control and high shear forces

Low polarity aliphatic systems 0.2 - 0.8 THIXCIN® R

M-P-A® 10X Complex polyolefin compound Xylene Liquid 9 - 11 Temperature control and high shear forces

Prevent pigment settling, especially for metallic paint

2.0 - 5.0 M-P-A® 10X

M-P-A® 20X Complex polyolefin compound Xylene Paste 19 - 21 Temperature control and high shear forces

Anti-settling for pigment, metallic and pearlescent paint in solvent-based coatings

0.5 - 2.0 M-P-A® 20X

M-P-A® 60X Organic compound Xylene Paste 22 - 26 Temperature and high shear forces Medium-high polarity aromatic and oxygenated systems

1.0 - 3.0 M-P-A® 60X

M-P-A® 1078 X Organic compound Xylene Paste 39 - 41 Temperature and high shear forces Industrial coatings, traffic paint, marine coatings 0.2 - 1.0 M-P-A® 1078 X



0.5 - 1.5 M-P-A® 2000 X



0.5 - 1.5 M-P-A® 4020 X

M-P-A® 4020BA Proprietary organic compound Butyl acetate Pourable liquid

20 Temperature and high hear forces Medium-high polarity aromatic and oxygenated HAPS free systems

0.5 - 1.5 M-P-A® 4020BA

DeuRheo 209 Polyamide wax Xylene/alcohols Paste 19 - 21 Temperature and shear forces Solvent-based coatings, ink, anti-corrosion primer, sealant

0.1 - 5.0 DeuRheo 209

DeuRheo 219 Polyamide wax Xylene/alcohols Paste 19 - 21 Temperature and shear forces Metallic, pearlescent, matte coatings 1.0 - 5.0 DeuRheo 219

DeuRheo 2810 Modified polyurea N-methyl pyrrolidone Liquid 50 - 54 Temperature and shear forces Medium polarity systems like epoxy coatings, polyurethane coatings

0.5 - 3.0 DeuRheo 2810

14


M-P-A® H105 Complex polyolefin Xylene Paste 4 - 6 High shear forces Metallic paint and pearlescent coatings 3.0 - 10.0 M-P-A® H105

M-P-A® E106A Synthetic wax Xylene, butyl acetate and

alcohol

Liquid 5 - 7 High shear forces Car refinish, slip agent for can and coil coatings, aluminium orientation

80 - 150 based on aluminium paste

M-P-A® E106A

DeuRheo 211 Polyethylene wax Xylene Paste 9.5 - 10.5 Temperature and high shear forces Metallic paint, pearlescent coatings and matte coatings

1.0 - 5.0 DeuRheo 211

DeuRheo 212 Polyethylene wax Xylene Paste 19 - 21 Co-grind Medium to low polarity systems, anti-corrosive coatings, industrial coatings

0.5 - 2.0 DeuRheo 212

DeuRheo 211F Polyethylene wax n-butyl acetate/ methyl cyclohexane

Paste 9.5 - 10.5 Temperature and high shear forces Suitable for use in virtually all solvent-based organic coatings including air drying and stoving systems

1.0 - 5.0 DeuRheo 211F

DeuRheo 202SP Polyethylene wax Xylene Paste 24 - 26 Co-grind Solvent-based systems, anti-corrosion systems 0.5 - 2.0 DeuRheo 202SP

DeuRheo 556 Ethylenevinyl acetate copolymer n-butyl acetate/xylene/

n-butyl alcohol

Paste 5.5 - 6.5 Temperature and high shear forces Recommended for use in solvent-based coatings and one coat metallic top coatings


DeuRheo 556

DeuRheo 556F Ethylene-vinyl acetate copolymer n-butyl acetate/ n-butyl alcohol

Paste 5.5 - 6.5 High speed stirring before use Recommended for solvent-based metallic coating


DeuRheo 556F

Product Composition Solvent Form Active % Principal Use Use Level % Product

DAPRO® BEZ 75 Liquid castor oil derivative Water Liquid 75 Activator to produce easy to handle BENTONE® pre-gels for aliphatic systems, improves anti-settling

25 - 50 on organoclay DAPRO® BEZ 75

DAPRO® FX 2060 Polyamide Xylene Isobutanol Liquid 50 Activator to produce easy to handle BENTONE® pre-gels 25 - 50 on organoclay DAPRO® FX 2060

Organic Rheological Additives

Chemical Activators

15


M-P-A® H105 Complex polyolefin Xylene Paste 4 - 6 High shear forces Metallic paint and pearlescent coatings 3.0 - 10.0 M-P-A® H105

M-P-A® E106A Synthetic wax Xylene, butyl acetate and

alcohol

Liquid 5 - 7 High shear forces Car refinish, slip agent for can and coil coatings, aluminium orientation


M-P-A® E106A

DeuRheo 211 Polyethylene wax Xylene Paste 9.5 - 10.5 Temperature and high shear forces Metallic paint, pearlescent coatings and matte coatings

1.0 - 5.0 DeuRheo 211

DeuRheo 212 Polyethylene wax Xylene Paste 19 - 21 Co-grind Medium to low polarity systems, anti-corrosive coatings, industrial coatings

0.5 - 2.0 DeuRheo 212

DeuRheo 211F Polyethylene wax n-butyl acetate/ methyl cyclohexane

Paste 9.5 - 10.5 Temperature and high shear forces Suitable for use in virtually all solvent-based organic coatings including air drying and stoving systems

1.0 - 5.0 DeuRheo 211F

DeuRheo 202SP Polyethylene wax Xylene Paste 24 - 26 Co-grind Solvent-based systems, anti-corrosion systems 0.5 - 2.0 DeuRheo 202SP

DeuRheo 556 Ethylenevinyl acetate copolymer n-butyl acetate/xylene/

n-butyl alcohol

Paste 5.5 - 6.5 Temperature and high shear forces Recommended for use in solvent-based coatings and one coat metallic top coatings


DeuRheo 556

DeuRheo 556F Ethylene-vinyl acetate copolymer n-butyl acetate/ n-butyl alcohol

Paste 5.5 - 6.5 High speed stirring before use Recommended for solvent-based metallic coating


DeuRheo 556F

Product Composition Solvent Form Active % Principal Use Use Level % Product

DAPRO® BEZ 75 Liquid castor oil derivative Water Liquid 75 Activator to produce easy to handle BENTONE® pre-gels for aliphatic systems, improves anti-settling

25 - 50 on organoclay DAPRO® BEZ 75

DAPRO® FX 2060 Polyamide Xylene Isobutanol Liquid 50 Activator to produce easy to handle BENTONE® pre-gels 25 - 50 on organoclay DAPRO® FX 2060

16

Product Composition Solvent FP* °C SG* Principal Use Use Level % Product

DAPRO® AP 1622 Silicone/hydrocarbon solvent Solvent blend 40 0.8 - 0.9 Solvent-based paint/coatings, clear oil and alkyd modified urethanes, OEM, equipment and machinery, metal furniture, plastic coatings, adhesives Inks

0.05 - 0.5 DAPRO® AP 1622

DAPRO® DF MOM Silicone-free hydrocarbon blend Mineral spirit/solvent naptha 26 0.83 Air-drying alkyd systems, alkyd-melamine baking enamels, acrylic isocyanate lacquers, nitrocellulose lacquers and acid-hardening lacquers

0.1 - 0.5 DAPRO® DF MOM

Defom 2700 Silicone-free polymer Aromatic hydrocarbon solvent 50 ca. 0.87 UV curing coatings, unsaturated polyester composites, epoxy coatings 0.1 - 1.0 Defom 2700

Defom 3100 Silicone-free polymer Aromatic hydrocarbon solvent 51 0.86 - 0.89 Unsaturated polyester coatings, UV-curable coatings, epoxy coatings 0.1 - 1.0 Defom 3100

Defom 3200 Silicone-free polymer Aliphatic hydrocarbon solvent 38 ca. 0.78 Sanding sealer, baking paint, nitrocellulose lacquer 0.1 - 0.5 Defom 3200

Defom 3500 Silicone-free polymer Aliphatic hydrocarbon solvent/butyl glycolate/ethylene glycol monobutyl ether

38 ca. 0.80 Wood primer coatings 0.1 - 0.5 Defom 3500

Defom 5300 Modified polysiloxane Cyclohexanone/aromatic hydrocarbon solvent 45 0.875 - 1.000 Solvent-based coatings 0.1 - 0.7 Defom 5300

Defom 5400 Modified polysiloxane Aromatic hydrocarbon solvent 42 0.850 - 0.875 Solvent-based coatings 0.1 - 0.7 Defom 5400

Defom 5800F Modified polysiloxane n-butyl acetate 27 0.86 - 0.90 Solvent-based coatings, toy coatings 0.1 - 0.7 Defom 5800F

Defom 6500 Modified polysiloxane Cyclohexanone 45 0.92 - 0.96 Solvent-based coatings, toy coatings, epoxy coatings 0.1 - 1.0 Defom 6500

Defom 6510 Modified polysiloxane n-butyl acetate 27 0.86 - 0.90 2K polyurethane coatings, solvent-based industrial coatings, epoxy coatings

0.1 - 1.7 Defom 6510

Defom 6700 Polysiloxane None 28 0.97 2K polyurethane coatings, solvent-based coatings, inks 0.1 - 0.2 Defom 6700

Defom 6800 Polysiloxane containing hydrophobic particles

None >100 0.96 - 1.00 Epoxy coatings, floor coatings 0.01 - 1.00 Defom 6800

* FP: Flash Point* SG: Specific Gravity

Defoamers


Product Composition Solvent FP* °C Form SG* Active % Principal Use Use Level % Product

NUOSPERSE® 15 Modified thermo-plastic acrylic polymer

PMA 42 Liquid 1.04 65 Colorants for industrial coatings 2 - 4 on total formulation-added in millbase 20 - 40 (sole binder for pigment pastes)

NUOSPERSE® 15


None None Powder 1.14 100 UV and high solids coatings 2 - 4 on total formulation-added in millbase 20 - 40 (sole binder for pigment pastes)

NUOSPERSE® 9100

NUOSPERSE® 2006 Multi functional anionic & non-ionic surfactant

Water >100 Liquid 1.09 62 - 65 Medium duty industrial coatings systems

0.1 - 1.0 on total formulation-added in millbase NUOSPERSE® 2006

NUOSPERSE® 2008 Multi functional surfactant None >100 Liquid 1.04 100 Solvent-free epoxy systems, solvent-free epoxy coatings


NUOSPERSE® AP 657 High molecular weight polyester Naphtha (petroleum),hydrotreated heavy

57 Liquid 0.95 72 - 76 Industrial and alkyd based systems 0.5 - 2.5 calculated on the pigment paste NUOSPERSE® AP 657

NUOSPERSE® FA 196 Surface active compound None >100 Liquid 1.04 100 High performance coatings, especially interesting for high solids and VOC free systems

0.1 - 0.5 on total formulation-added in millbase NUOSPERSE® FA 196

NUOSPERSE® FA 601 Combination of surfaceactive agents in solution

Solvent mixture 41 Liquid 1.01 50 Architectural and industrial coatings 0.1 - 1.0 on total formulation-added in millbase NUOSPERSE® FA 601

NUOSPERSE® FX 9086 Polymeric surfactant dissolved in methoxy propyl acetate

PMA 42 Liquid 1.02 50 Industrial coatings 0.5 - 1.5 on total formulation-added in millbase NUOSPERSE® FX 9086

17

Product Composition Solvent FP* °C SG* Principal Use Use Level % Product

DAPRO® AP 1622 Silicone/hydrocarbon solvent Solvent blend 40 0.8 - 0.9 Solvent-based paint/coatings, clear oil and alkyd modified urethanes, OEM, equipment and machinery, metal furniture, plastic coatings, adhesives Inks

0.05 - 0.5 DAPRO® AP 1622

DAPRO® DF MOM Silicone-free hydrocarbon blend Mineral spirit/solvent naptha 26 0.83 Air-drying alkyd systems, alkyd-melamine baking enamels, acrylic isocyanate lacquers, nitrocellulose lacquers and acid-hardening lacquers

0.1 - 0.5 DAPRO® DF MOM

Defom 2700 Silicone-free polymer Aromatic hydrocarbon solvent 50 ca. 0.87 UV curing coatings, unsaturated polyester composites, epoxy coatings 0.1 - 1.0 Defom 2700

Defom 3100 Silicone-free polymer Aromatic hydrocarbon solvent 51 0.86 - 0.89 Unsaturated polyester coatings, UV-curable coatings, epoxy coatings 0.1 - 1.0 Defom 3100

Defom 3200 Silicone-free polymer Aliphatic hydrocarbon solvent 38 ca. 0.78 Sanding sealer, baking paint, nitrocellulose lacquer 0.1 - 0.5 Defom 3200

Defom 3500 Silicone-free polymer Aliphatic hydrocarbon solvent/butyl glycolate/ethylene glycol monobutyl ether

38 ca. 0.80 Wood primer coatings 0.1 - 0.5 Defom 3500

Defom 5300 Modified polysiloxane Cyclohexanone/aromatic hydrocarbon solvent 45 0.875 - 1.000 Solvent-based coatings 0.1 - 0.7 Defom 5300

Defom 5400 Modified polysiloxane Aromatic hydrocarbon solvent 42 0.850 - 0.875 Solvent-based coatings 0.1 - 0.7 Defom 5400

Defom 5800F Modified polysiloxane n-butyl acetate 27 0.86 - 0.90 Solvent-based coatings, toy coatings 0.1 - 0.7 Defom 5800F

Defom 6500 Modified polysiloxane Cyclohexanone 45 0.92 - 0.96 Solvent-based coatings, toy coatings, epoxy coatings 0.1 - 1.0 Defom 6500

Defom 6510 Modified polysiloxane n-butyl acetate 27 0.86 - 0.90 2K polyurethane coatings, solvent-based industrial coatings, epoxy coatings

0.1 - 1.7 Defom 6510

Defom 6700 Polysiloxane None 28 0.97 2K polyurethane coatings, solvent-based coatings, inks 0.1 - 0.2 Defom 6700

Defom 6800 Polysiloxane containing hydrophobic particles

None >100 0.96 - 1.00 Epoxy coatings, floor coatings 0.01 - 1.00 Defom 6800



PMA 42 Liquid 1.04 65 Colorants for industrial coatings 2 - 4 on total formulation-added in millbase 20 - 40 (sole binder for pigment pastes)

NUOSPERSE® 15


None None Powder 1.14 100 UV and high solids coatings 2 - 4 on total formulation-added in millbase 20 - 40 (sole binder for pigment pastes)

NUOSPERSE® 9100

NUOSPERSE® 2006 Multi functional anionic & non-ionic surfactant

Water >100 Liquid 1.09 62 - 65 Medium duty industrial coatings systems


NUOSPERSE® 2008 Multi functional surfactant None >100 Liquid 1.04 100 Solvent-free epoxy systems, solvent-free epoxy coatings


NUOSPERSE® AP 657 High molecular weight polyester Naphtha (petroleum),hydrotreated heavy

57 Liquid 0.95 72 - 76 Industrial and alkyd based systems 0.5 - 2.5 calculated on the pigment paste NUOSPERSE® AP 657

NUOSPERSE® FA 196 Surface active compound None >100 Liquid 1.04 100 High performance coatings, especially interesting for high solids and VOC free systems

0.1 - 0.5 on total formulation-added in millbase NUOSPERSE® FA 196

NUOSPERSE® FA 601 Combination of surfaceactive agents in solution

Solvent mixture 41 Liquid 1.01 50 Architectural and industrial coatings 0.1 - 1.0 on total formulation-added in millbase NUOSPERSE® FA 601

NUOSPERSE® FX 9086 Polymeric surfactant dissolved in methoxy propyl acetate

PMA 42 Liquid 1.02 50 Industrial coatings 0.5 - 1.5 on total formulation-added in millbase NUOSPERSE® FX 9086

18



NUOSPERSE® FX 9200 Highly branched copolymer None >100 Powder 1.13 100 Inks 20 - 40 Organic pigments40 - 100 Carbon black

NUOSPERSE® FX 9200

NUOSPERSE® FX 9360 Highly branched copolymer n-Butyl acetate 31 Liquid 0.98 40 Colorants, automotive and plastic coatings 20 - 40 Organic pigments40 - 100 Carbon black

NUOSPERSE® FX 9360

Disponer 903 Modified polysiloxane Xylene/Isobutyl alcohol 24 Liquid ca. 0.85 8.5 - 10.5 Solvent-based colored paint 0.1 - 1.0 Disponer 903

Disponer 904 High molecular weight carboxylic acid

Xylene/diisobutyl ketone 33 Liquid ca. 0.94 49 - 51 Medium to high polarity solvent and solvent-free systems

0.5 - 3.0 Inorganic pigments 2.0 - 5.0 Organic pigments

Disponer 904

Disponer 923 Electro-neutral amine salt of polycar-boxylic acid

Aromatic hydrocarbon solvent

34 Liquid ca. 0.89 48 - 52 Medium to high polarity inorganic pigment systems

As dispersant: 0.5 - 2.0 based on total pigmentsAs organoclay activator: 30 - 50 based on BENTONE®

Disponer 923

Disponer 926 Anionic surfactant None >100 Liquid ca. 1.04 82 - 88 Medium to high polarity organic pigment systems

Organic pigment: 1.0 - 3.0 based on pigment Inorganic pigment: 0.5 - 1.5 based on pigment

Disponer 926

Disponer 929 Anionic surfactant Xylene/aromatic hydrocarbon solvent/n-

butyl acetate

26 Liquid ca. 0.97 48 - 51 Organic pigment systems As a sole grinding vehicle: 20 - 50 based on total formulationAs a wetting and dispersing agent: incorporate before grinding, dispersing with pigment

Disponer 929

Disponer 983 High molecular weight polymer Xylene/butyl acetate 34 Liquid 0.95 - 0.99 52.5 - 54.5 Solvent-based coatings Carbon black: 20 - 80 based on pigment

Disponer 983

Disponer 904S Solution of polycarboxylic acid polymer with a polysiloxane copolymer

Xylene/diisobutyl ketone 33 Liquid 0.92 - 0.95 49 - 51 Medium to high polarity solvent and solvent-free systems


Disponer 904S

Disponer 912A Solution of a salt of polyamide and polyester, electro-neutral

Xylene/Isobutyl alcohol 34 Liquid ca. 0.91 48 - 52 Solvent-based coatings, wood primer 0.2 - 5.0 based on inorganic pigment 0.2 - 0.4 based on wood primers As organoclay activator:30 - 50 based on BENTONE®

Disponer 912A

Disponer 923S Electro-neutral amine salt of polycarboxylic acid with polysiloxane




Disponer 923S

Disponer 9250 Solution of a copolymer with acidic groups

Aromatic hydrocarbon solvent/PMAC

45 Liquid 1.01 - 1.05 48.5 - 51.5 Acrylic/melamine, acrylic polyurethane 2 - 5 based on pigment Disponer 9250

Disponer 9850 Modified polyurethane Xylene/propylene glycol monomethyl ether

acetate/n-butyl acetate

30 Liquid 0.96 - 1.00 44 - 47 Acrylic/melamine, alkyd/melamine, acrylic polyurethane

40 - 120 based on pigment Disponer 9850


19


NUOSPERSE® FX 9200 Highly branched copolymer None >100 Powder 1.13 100 Inks 20 - 40 Organic pigments40 - 100 Carbon black

NUOSPERSE® FX 9200

NUOSPERSE® FX 9360 Highly branched copolymer n-Butyl acetate 31 Liquid 0.98 40 Colorants, automotive and plastic coatings 20 - 40 Organic pigments40 - 100 Carbon black

NUOSPERSE® FX 9360

Disponer 903 Modified polysiloxane Xylene/Isobutyl alcohol 24 Liquid ca. 0.85 8.5 - 10.5 Solvent-based colored paint 0.1 - 1.0 Disponer 903

Disponer 904 High molecular weight carboxylic acid

Xylene/diisobutyl ketone 33 Liquid ca. 0.94 49 - 51 Medium to high polarity solvent and solvent-free systems


Disponer 904

Disponer 923 Electro-neutral amine salt of polycar-boxylic acid




Disponer 923

Disponer 926 Anionic surfactant None >100 Liquid ca. 1.04 82 - 88 Medium to high polarity organic pigment systems

Organic pigment: 1.0 - 3.0 based on pigment Inorganic pigment: 0.5 - 1.5 based on pigment

Disponer 926

Disponer 929 Anionic surfactant Xylene/aromatic hydrocarbon solvent/n-

butyl acetate

26 Liquid ca. 0.97 48 - 51 Organic pigment systems As a sole grinding vehicle: 20 - 50 based on total formulationAs a wetting and dispersing agent: incorporate before grinding, dispersing with pigment

Disponer 929

Disponer 983 High molecular weight polymer Xylene/butyl acetate 34 Liquid 0.95 - 0.99 52.5 - 54.5 Solvent-based coatings Carbon black: 20 - 80 based on pigment

Disponer 983

Disponer 904S Solution of polycarboxylic acid polymer with a polysiloxane copolymer

Xylene/diisobutyl ketone 33 Liquid 0.92 - 0.95 49 - 51 Medium to high polarity solvent and solvent-free systems


Disponer 904S

Disponer 912A Solution of a salt of polyamide and polyester, electro-neutral

Xylene/Isobutyl alcohol 34 Liquid ca. 0.91 48 - 52 Solvent-based coatings, wood primer 0.2 - 5.0 based on inorganic pigment 0.2 - 0.4 based on wood primers As organoclay activator:30 - 50 based on BENTONE®

Disponer 912A

Disponer 923S Electro-neutral amine salt of polycarboxylic acid with polysiloxane




Disponer 923S

Disponer 9250 Solution of a copolymer with acidic groups

Aromatic hydrocarbon solvent/PMAC

45 Liquid 1.01 - 1.05 48.5 - 51.5 Acrylic/melamine, acrylic polyurethane 2 - 5 based on pigment Disponer 9250

Disponer 9850 Modified polyurethane Xylene/propylene glycol monomethyl ether

acetate/n-butyl acetate

30 Liquid 0.96 - 1.00 44 - 47 Acrylic/melamine, alkyd/melamine, acrylic polyurethane

40 - 120 based on pigment Disponer 9850

20

Product Composition Solvent FP*°C SG* Active % Principal Use Use Level % Product

Levaslip 411 Modified polysiloxane Toluene 4.4 ca. 0.875 6.7 - 7.7 Solvent-based coatings 0.05 - 0.50 Levaslip 411

Levaslip 412 Modified polysiloxane Xylene/Toluene 7 0.86 - 0.88 9 - 11 Solventless & solvent-based coatings, UV & Leather coatings

0.05 - 0.5 Levaslip 412

Levaslip 432 Modified polysiloxane Xylene/ethyleneglycol monobutylether

31 0.87 - 0.90 13 - 14 Solvent-based coatings 0.1 - 0.5 Levaslip 432

Levaslip 435 Modified polysiloxane None >100 ca. 0.964 > 98 Solvent-based coatings 0.05 - 0.30 Levaslip 435

Levaslip 455 Modified polysiloxane Ethylglycol monobutyl ether 66 ca. 0.96 48 - 52 Waterborne and solvent-based coatings 0.1 - 0.5 Levaslip 455


46 ca. 0.9 23.5 - 25.5 Solvent-based coatings 0.1 - 0.5 Levaslip 466

Levaslip 468 Modified polysiloxane None 80 1.00 - 1.03 100 Solvent-based and solvent-free coatings, UV curable coating

0.01 - 0.2 Levaslip 468

Levaslip 836 Modified polysiloxane Xylene/isobutanol 26 ca. 0.88 23 - 25 Solvent-based coatings 0.1 - 0.5 Levaslip 836

Levaslip 871 Polyester modified polysiloxane

Xylene 31 0.89 - 0.93 24.0 - 26.0 Solvent-based coatings 0.1 - 0.5 Levaslip 871


Xylene 31 0.88 - 0.92 25 - 27 Polyester/melamine, alkyd/melamine, acrylic/melamine 0.1 - 0.5 Levaslip 872

Levaslip 873 Modified polysiloxane None >100 1.04 - 1.05 > 95 N/C lacquer, 2K - PU coatings 0.1 - 0.5 Levaslip 873

Levaslip 875 Modified polysiloxane Aromatic hydrocarbon solvent/γ-butyrolactone

56 0.98 - 1.01 47 - 52 Nitrocellulose lacquer, polyurethane, acid curing 0.1 - 0.5 Levaslip 875

Levaslip 876 Modified polysiloxane Xylene/ethylene glycol phenyl ether


Levaslip 879 Modified polysiloxane None >100 1.02 - 1.03 > 95 Polyurethane, Nitrocellulose lacquer, acid curing, waterborne

0.1 - 1.0 Levaslip 879

Levaslip 882 Modified polysiloxane Aromatic hydrocarbon solvent/butyrolactone

58 1.00 - 1.03 48 - 52 Nitrocellulose lacquer, 2K polyurethane 0.1 - 1.0 Levaslip 882

Levaslip 8627 Modified polysiloxane None 110 1.03 100 Solvent & UV curable system 0.05 - 2.0 Levaslip 8627

Levelol 491 Acrylic copolymer Aromatic hydrocarbon solvent >100 ca. 1.04 98.5 - 100 Solvent-based coatings 0.4 - 2.0 Levelol 491

Levelol 495 Acrylic copolymer Xylene 39 ca. 0.95 48 - 52 Solvent-based coatings 0.2 - 1.0 Levelol 495

Levelol 835 Acrylic copolymer Aromatic hydrocarbon solvent 46 ca. 0.94 49.5 - 51.5 Solvent-based coatings 0.1 - 1.0 Levelol 835

Levelol 837 Fluorocarbon modified polyacrylate

Xylene 36 ca. 0.98 69.0 - 72.0 Solvent-based coatings 0.1 - 0.5 Levelol 837


Propylene glycol methyl ether acetate

46 ca. 1.0 49.0 – 51.0 Solvent-based coatings 0.05 - 0.50 Levelol 839

Levelol TSP High boiling point solvents with surfactant

Aromatic hydrocarbon solvent >100 ca. 0.94 100 Solvent-based coatings 5 - 10 based on total solvent 2 - 5 based on total formulation is recommended

Levelol TSP

Leveling Agents


21

Product Composition Solvent FP*°C SG* Active % Principal Use Use Level % Product

Levaslip 411 Modified polysiloxane Toluene 4.4 ca. 0.875 6.7 - 7.7 Solvent-based coatings 0.05 - 0.50 Levaslip 411

Levaslip 412 Modified polysiloxane Xylene/Toluene 7 0.86 - 0.88 9 - 11 Solventless & solvent-based coatings, UV & Leather coatings

0.05 - 0.5 Levaslip 412


31 0.87 - 0.90 13 - 14 Solvent-based coatings 0.1 - 0.5 Levaslip 432

Levaslip 435 Modified polysiloxane None >100 ca. 0.964 > 98 Solvent-based coatings 0.05 - 0.30 Levaslip 435

Levaslip 455 Modified polysiloxane Ethylglycol monobutyl ether 66 ca. 0.96 48 - 52 Waterborne and solvent-based coatings 0.1 - 0.5 Levaslip 455



Levaslip 468 Modified polysiloxane None 80 1.00 - 1.03 100 Solvent-based and solvent-free coatings, UV curable coating

0.01 - 0.2 Levaslip 468

Levaslip 836 Modified polysiloxane Xylene/isobutanol 26 ca. 0.88 23 - 25 Solvent-based coatings 0.1 - 0.5 Levaslip 836


Xylene 31 0.89 - 0.93 24.0 - 26.0 Solvent-based coatings 0.1 - 0.5 Levaslip 871


Xylene 31 0.88 - 0.92 25 - 27 Polyester/melamine, alkyd/melamine, acrylic/melamine 0.1 - 0.5 Levaslip 872

Levaslip 873 Modified polysiloxane None >100 1.04 - 1.05 > 95 N/C lacquer, 2K - PU coatings 0.1 - 0.5 Levaslip 873

Levaslip 875 Modified polysiloxane Aromatic hydrocarbon solvent/γ-butyrolactone

56 0.98 - 1.01 47 - 52 Nitrocellulose lacquer, polyurethane, acid curing 0.1 - 0.5 Levaslip 875

Levaslip 876 Modified polysiloxane Xylene/ethylene glycol phenyl ether


Levaslip 879 Modified polysiloxane None >100 1.02 - 1.03 > 95 Polyurethane, Nitrocellulose lacquer, acid curing, waterborne

0.1 - 1.0 Levaslip 879

Levaslip 882 Modified polysiloxane Aromatic hydrocarbon solvent/butyrolactone

58 1.00 - 1.03 48 - 52 Nitrocellulose lacquer, 2K polyurethane 0.1 - 1.0 Levaslip 882

Levaslip 8627 Modified polysiloxane None 110 1.03 100 Solvent & UV curable system 0.05 - 2.0 Levaslip 8627

Levelol 491 Acrylic copolymer Aromatic hydrocarbon solvent >100 ca. 1.04 98.5 - 100 Solvent-based coatings 0.4 - 2.0 Levelol 491

Levelol 495 Acrylic copolymer Xylene 39 ca. 0.95 48 - 52 Solvent-based coatings 0.2 - 1.0 Levelol 495

Levelol 835 Acrylic copolymer Aromatic hydrocarbon solvent 46 ca. 0.94 49.5 - 51.5 Solvent-based coatings 0.1 - 1.0 Levelol 835


Xylene 36 ca. 0.98 69.0 - 72.0 Solvent-based coatings 0.1 - 0.5 Levelol 837


Propylene glycol methyl ether acetate

46 ca. 1.0 49.0 – 51.0 Solvent-based coatings 0.05 - 0.50 Levelol 839

Levelol TSP High boiling point solvents with surfactant

Aromatic hydrocarbon solvent >100 ca. 0.94 100 Solvent-based coatings 5 - 10 based on total solvent 2 - 5 based on total formulation is recommended

Levelol TSP

22

Interfacial Tension ModifiersProduct Composition Solvent FP* °C SG* FDA Active % Principal Use Use Level % Product

DAPRO® S-65 Blend of surfactants Blend of aromatic 150 & n-Butanol 47 0.98 No 75 Architectural and industrial coatings 0.05 - 0.5 DAPRO® S-65

DAPRO® U-99 Blend of surfactants Blend of Ethanol, butoxyethanol & water

51 1.01 175 - 300 50 Architectural and industrial coatings 0.25 - 1.0 DAPRO® U-99


Product Composition Solvent FP* °C SG* Active % Principal Use Use Level % Product

DAPRO® ALT 009 Phosphate modified polymer

Propylene glycol methyl ether/Propylene glycol methyl ether acetate

34 ca. 1.01 49 - 53 Provide passivation and deflocculation for metallic pigments in solvent based or waterborne paint formulations

10 - 40 based on metallic pigments DAPRO® ALT 009

DAPRO® FK 321 Quaternary ammonium Isobutanol 27 - 29 0.94 75 Solvent-based industrial electrostatically applied coatings 0.1 - 2.5 DAPRO® FK 321

Catacure KB Acidic polymer N-butyl acetate/cyclohexanone/isobutanol

37 ca. 1.1 66 - 70 Partially butylated melamine baking paint 1.0 - 3.0 Catacure KB

Catacure KC Amine salt of p-toluene sulfonic acid

Propylene glycol monomethyl ether/propylene

glycol

32 ca. 0.96 23 - 25 Partially butylated or HMMM melamine baking paint 1.0 - 4.0 Catacure KC

DeuAdd DVP Combination of special surfactants

Xylene/isobutanol 25 0.85 - 0.89 8.0 - 10.0 Oxidation drying coatings, alkyd baking paint 1.0 - 2.0 base on total solid content of paint

DeuAdd DVP

DeuAdd HM-6 High molecular weight silicone

Xylene 25 0.86 - 0.88 9 - 11 Aluminum coatings, alkyd/melamine, oxidation drying 0.05 - 0.5 DeuAdd HM-6

DeuWax FA-110 Polyethylene wax Xylene/n-butyl acetate 29 ca. 0.88 9.5 - 10.0 Matte coatings 10.0 - 20.0 based on total formulation for semigloss

DeuWax FA-110

Speciality Additives

Adhesion PromotersProduct Composition Solvent FP* °C SG* Active % Principal Use Use Level % Product

Adherant 1121 Amino silane N-butanol 32 0.89 - 0.92 ca. 50 Improve adhesion of organic resin to inorganic surfaces 1.0 - 2.0 based on total resin solids, add during let-down stage

Adherant 1121

Adherant 1051 Epoxy silane None 101.1 1.045 - 1.075 ca. 100 Improve adhesion of organic resin to inorganic surfaces 0.5 - 2.0 Adherant 1051

Adherant ADP Non-silicone polymeric compound

Isopropanol 59 1.08 - 1.10 78 - 82 Improve adhesion of Alkyd/Acrylic melamine baking paint to metal surfaces

1.5 - 2.5 Adherant ADP

Adherant APC Non-silicone polymer Dimethyl/carbonate/xylene 27 ca. 1.06 48 - 52 Improve adhesion of two-component polyurethane to polycarbonate

1.0 - 5.0 Adherant APC

Adherant APW Non-silicone polymeric solution

Xylene 28 1.01 - 1.03 58 - 62 Improve the interaction force of aluminum flake with binder 2.0 - 5.0 Adherant APW

Adherant APX Modified acrylate oligmer None >100 1.188 ≥ 94 Improve adhesion of UV curable coatings to metal surfaces 1 - 5 based on resin Adherant APX

Adherant PPB Chlorinated polyolefin Toluene 10 ca. 0.895 14 - 16 Primer of PP or PP/EPDM substrates 10.0 - 15.0 based on total formulation and mix thoroughly

Adherant PPB

23

Product Composition Solvent FP* °C SG* FDA Active % Principal Use Use Level % Product

DAPRO® S-65 Blend of surfactants Blend of aromatic 150 & n-Butanol 47 0.98 No 75 Architectural and industrial coatings 0.05 - 0.5 DAPRO® S-65

DAPRO® U-99 Blend of surfactants Blend of Ethanol, butoxyethanol & water

51 1.01 175 - 300 50 Architectural and industrial coatings 0.25 - 1.0 DAPRO® U-99


DAPRO® ALT 009 Phosphate modified polymer

Propylene glycol methyl ether/Propylene glycol methyl ether acetate

34 ca. 1.01 49 - 53 Provide passivation and deflocculation for metallic pigments in solvent based or waterborne paint formulations

10 - 40 based on metallic pigments DAPRO® ALT 009

DAPRO® FK 321 Quaternary ammonium Isobutanol 27 - 29 0.94 75 Solvent-based industrial electrostatically applied coatings 0.1 - 2.5 DAPRO® FK 321

Catacure KB Acidic polymer N-butyl acetate/cyclohexanone/isobutanol

37 ca. 1.1 66 - 70 Partially butylated melamine baking paint 1.0 - 3.0 Catacure KB

Catacure KC Amine salt of p-toluene sulfonic acid

Propylene glycol monomethyl ether/propylene

glycol

32 ca. 0.96 23 - 25 Partially butylated or HMMM melamine baking paint 1.0 - 4.0 Catacure KC

DeuAdd DVP Combination of special surfactants

Xylene/isobutanol 25 0.85 - 0.89 8.0 - 10.0 Oxidation drying coatings, alkyd baking paint 1.0 - 2.0 base on total solid content of paint

DeuAdd DVP

DeuAdd HM-6 High molecular weight silicone

Xylene 25 0.86 - 0.88 9 - 11 Aluminum coatings, alkyd/melamine, oxidation drying 0.05 - 0.5 DeuAdd HM-6

DeuWax FA-110 Polyethylene wax Xylene/n-butyl acetate 29 ca. 0.88 9.5 - 10.0 Matte coatings 10.0 - 20.0 based on total formulation for semigloss

DeuWax FA-110


Adherant 1121 Amino silane N-butanol 32 0.89 - 0.92 ca. 50 Improve adhesion of organic resin to inorganic surfaces 1.0 - 2.0 based on total resin solids, add during let-down stage

Adherant 1121

Adherant 1051 Epoxy silane None 101.1 1.045 - 1.075 ca. 100 Improve adhesion of organic resin to inorganic surfaces 0.5 - 2.0 Adherant 1051

Adherant ADP Non-silicone polymeric compound

Isopropanol 59 1.08 - 1.10 78 - 82 Improve adhesion of Alkyd/Acrylic melamine baking paint to metal surfaces

1.5 - 2.5 Adherant ADP

Adherant APC Non-silicone polymer Dimethyl/carbonate/xylene 27 ca. 1.06 48 - 52 Improve adhesion of two-component polyurethane to polycarbonate

1.0 - 5.0 Adherant APC

Adherant APW Non-silicone polymeric solution

Xylene 28 1.01 - 1.03 58 - 62 Improve the interaction force of aluminum flake with binder 2.0 - 5.0 Adherant APW

Adherant APX Modified acrylate oligmer None >100 1.188 ≥ 94 Improve adhesion of UV curable coatings to metal surfaces 1 - 5 based on resin Adherant APX

Adherant PPB Chlorinated polyolefin Toluene 10 ca. 0.895 14 - 16 Primer of PP or PP/EPDM substrates 10.0 - 15.0 based on total formulation and mix thoroughly

Adherant PPB

24

Product Composition Solvent FP*°C Average Particle size μm

FDA Clearance CFR Title 21

Hardness ASTM D-5

Softening range ℉ / ℃ Principal Use Use

Level % Product

SLIP-AYD® SL 50 Polyethylene wax, 22.5 % Xylene 61.5 % 27 10 - 15 175.300 3.0 - 3.5 220 - 225/104 - 107 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.5 - 3.0 SLIP-AYD® SL 50

SLIP-AYD® SL 177 High melt polyethylene, wax 23 % Xylene 77 % 27 10 - 15 None < 0.5 280 - 290/138 - 143 Auto OEM/refinish, agricultural /industrial equipment, furniture/appliance, coil/can (non food)

1.0 - 4.0 SLIP-AYD® SL 177

SLIP-AYD® SL 404 Hard polymeric wax, 18 % 2-butoxy ethanol 82 % 62 2 - 5 175.300 2.0 - 2.5 200 - 210/93 - 99 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.25 - 1.0 SLIP-AYD® SL 404

SLIP-AYD® SL 444 Non-reactive type of polysiloxane, 50 %

Dipropylene glycol > 80 None None None None High polarity coating systems, ink systems, water base industrial coatings

0.04 - 0.3 SLIP-AYD® SL 444

SLIP-AYD® SL 523 Hard polymeric wax, 18 % Isopropanol 82 % 12 2 - 4 Yes 2.0 - 2.5 200 - 210/93 - 99 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.25 - 1.0 SLIP-AYD® SL 523

SLIP-AYD® SL 551 High melt polyethylene, wax 18.5 %

Aromatic 100: 61.5 % n-Butanol: 20 %

36 2 - 3 None < 0.5 280 - 290/138 - 143 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can (non food) can

1.0 - 4.0 SLIP-AYD® SL 551

* FP: Flash Point

Surface Modifiers

Product Composition Solvent Non-volatile content %

Specific gravity OH % OH value,

mg KOH / g Dynamic viscosity,

cP (25℃)Acid value, mg KOH / g Principal Use Product

Hypomer FX-2050 Hydroxyl acrylic copolymer Toluene/n-butyl acetate 50 - 52 1.01 1.0 33 2750 - 4350 3 - 6 Plastic coatings, Metallic coatings, Wood coatings

Hypomer FX-2050

Hypomer FX-2060AF Hydroxyl acrylic copolymer n-butyl acetate 58 - 62 1.03 1.2 39.6 6700 - 13700 3 - 8 Automobile refinishes, Plastic coatings Hypomer FX-2060AF

Hypomer FX-2060D Hydroxyl acrylic copolymer Xylene/n-butyl acetate 58 - 61 1.03 1.2 39.6 6500 - 10000 3 - 8 Plastic coatings, Metal coatings Hypomer FX-2060D

Hypomer FX-2451F Hydroxyl acrylic copolymer n-butyl acetate 48 - 52 1.01 1.2 39.6 10000 - 20000 4 - 8 Plastic coatings Hypomer FX-2451FHypomer FX-2460AF Hydroxyl acrylic copolymer n-butyl acetate/propylene

glycol monomethyl ether acetate

59 - 63 1.06 1.44 47.52 4500 - 12500 9 - 14 Plastic coatings, Exterior application Hypomer FX-2460AF

Hypomer FX-2820F Hydroxyl acrylic copolymer n-butyl acetate 58 - 62 1.03 1.68 55.44 2500 - 6500 5 - 12 Exterior coatings, Automobile refinishes Hypomer FX-2820FHypomer FX-2860A Hydroxyl acrylic copolymer Xylene/n-butyl acetate 58 - 62 1.02 1.68 55.4 2500 - 4400 10 - 15 Automobile refinishes, Motorcycle

coatings, Wood coatingsHypomer FX-2860A

Hypomer FX-2970A Hydroxyl acrylic copolymer Xylene/n-butyl acetate/ ethylene glycol monoethyl

ether acetate

67.5 - 70.5 1.03 2.03 67.0 3000 - 6000 3 - 7 Plastic coatings, Automobile refinish, Transportations and industrial applications

Hypomer FX-2970A

Hypomer FX-3270 Hydroxyl acrylic copolymer n-butyl acetate/xylene 67 - 71 1.03 2.24 73.9 3700 - 6200 5 - 10 Automobile refinish, Transportation, Industrial applications

Hypomer FX-3270

Hypomer FX-4365 Hydroxyl acrylic copolymer Xylene/n-butyl acetate/ ethylene glycol monoethyl

ether acetate

62.5 - 65.5 1.03 2.8 92.2 2600 - 4300 8 - 15 Car refinishes, Plastic coatings Hypomer FX-4365

Hypomer MT-2550F Acrylic copolymer with special groups

Iso-Butyl isobutyrate/ Propylene glycol monomethyl

ether acetate

47- 51 1.04 1.23 40.6 4000 -10000 12 - 32 Plastic coatings, Industrial coatings, Wood coatings, Transportations

Hypomer MT-2550F

Hypomer PE-8043F Hydroxylate polyester polyol Xylene/n-butyl acetate 77 - 81 1.09 3.44 113.5 1800 - 2800 ≤ 10 Plastic coatings Hypomer PE-8043FBLR-8086 Blocked aliphatic

polyisocyanateXylene/n-butyl acetate 74 - 76 1.05 - 1.09 －－－－ One-component PU baking paint BLR-8086

Hypomer UA-M6 Acrylic acrylate n-butyl acetate 65 - 68 1.0 －－ 1200 - 2200 － Topcoat for aluminum basecoat, Plastic coating

Hypomer UA-M6

Resins

25

Product Composition Solvent FP*°C Average Particle size μm

FDA Clearance CFR Title 21

Hardness ASTM D-5

Softening range ℉ / ℃ Principal Use Use

Level % Product

SLIP-AYD® SL 50 Polyethylene wax, 22.5 % Xylene 61.5 % 27 10 - 15 175.300 3.0 - 3.5 220 - 225/104 - 107 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.5 - 3.0 SLIP-AYD® SL 50

SLIP-AYD® SL 177 High melt polyethylene, wax 23 % Xylene 77 % 27 10 - 15 None < 0.5 280 - 290/138 - 143 Auto OEM/refinish, agricultural /industrial equipment, furniture/appliance, coil/can (non food)

1.0 - 4.0 SLIP-AYD® SL 177

SLIP-AYD® SL 404 Hard polymeric wax, 18 % 2-butoxy ethanol 82 % 62 2 - 5 175.300 2.0 - 2.5 200 - 210/93 - 99 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.25 - 1.0 SLIP-AYD® SL 404

SLIP-AYD® SL 444 Non-reactive type of polysiloxane, 50 %

Dipropylene glycol > 80 None None None None High polarity coating systems, ink systems, water base industrial coatings

0.04 - 0.3 SLIP-AYD® SL 444

SLIP-AYD® SL 523 Hard polymeric wax, 18 % Isopropanol 82 % 12 2 - 4 Yes 2.0 - 2.5 200 - 210/93 - 99 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can

0.25 - 1.0 SLIP-AYD® SL 523

SLIP-AYD® SL 551 High melt polyethylene, wax 18.5 %

Aromatic 100: 61.5 % n-Butanol: 20 %

36 2 - 3 None < 0.5 280 - 290/138 - 143 Auto OEM/refinish, agricultural/industrial equipment, furniture/appliance, coil/can (non food) can

1.0 - 4.0 SLIP-AYD® SL 551

Product Composition Solvent Non-volatile content %

Specific gravity OH % OH value,

mg KOH / g Dynamic viscosity,

cP (25℃)Acid value, mg KOH / g Principal Use Product

Hypomer FX-2050 Hydroxyl acrylic copolymer Toluene/n-butyl acetate 50 - 52 1.01 1.0 33 2750 - 4350 3 - 6 Plastic coatings, Metallic coatings, Wood coatings

Hypomer FX-2050

Hypomer FX-2060AF Hydroxyl acrylic copolymer n-butyl acetate 58 - 62 1.03 1.2 39.6 6700 - 13700 3 - 8 Automobile refinishes, Plastic coatings Hypomer FX-2060AF

Hypomer FX-2060D Hydroxyl acrylic copolymer Xylene/n-butyl acetate 58 - 61 1.03 1.2 39.6 6500 - 10000 3 - 8 Plastic coatings, Metal coatings Hypomer FX-2060D

Hypomer FX-2451F Hydroxyl acrylic copolymer n-butyl acetate 48 - 52 1.01 1.2 39.6 10000 - 20000 4 - 8 Plastic coatings Hypomer FX-2451FHypomer FX-2460AF Hydroxyl acrylic copolymer n-butyl acetate/propylene

glycol monomethyl ether acetate

59 - 63 1.06 1.44 47.52 4500 - 12500 9 - 14 Plastic coatings, Exterior application Hypomer FX-2460AF

Hypomer FX-2820F Hydroxyl acrylic copolymer n-butyl acetate 58 - 62 1.03 1.68 55.44 2500 - 6500 5 - 12 Exterior coatings, Automobile refinishes Hypomer FX-2820FHypomer FX-2860A Hydroxyl acrylic copolymer Xylene/n-butyl acetate 58 - 62 1.02 1.68 55.4 2500 - 4400 10 - 15 Automobile refinishes, Motorcycle

coatings, Wood coatingsHypomer FX-2860A

Hypomer FX-2970A Hydroxyl acrylic copolymer Xylene/n-butyl acetate/ ethylene glycol monoethyl

ether acetate

67.5 - 70.5 1.03 2.03 67.0 3000 - 6000 3 - 7 Plastic coatings, Automobile refinish, Transportations and industrial applications

Hypomer FX-2970A

Hypomer FX-3270 Hydroxyl acrylic copolymer n-butyl acetate/xylene 67 - 71 1.03 2.24 73.9 3700 - 6200 5 - 10 Automobile refinish, Transportation, Industrial applications

Hypomer FX-3270

Hypomer FX-4365 Hydroxyl acrylic copolymer Xylene/n-butyl acetate/ ethylene glycol monoethyl

ether acetate

62.5 - 65.5 1.03 2.8 92.2 2600 - 4300 8 - 15 Car refinishes, Plastic coatings Hypomer FX-4365

Hypomer MT-2550F Acrylic copolymer with special groups

Iso-Butyl isobutyrate/ Propylene glycol monomethyl

ether acetate

47- 51 1.04 1.23 40.6 4000 -10000 12 - 32 Plastic coatings, Industrial coatings, Wood coatings, Transportations

Hypomer MT-2550F

Hypomer PE-8043F Hydroxylate polyester polyol Xylene/n-butyl acetate 77 - 81 1.09 3.44 113.5 1800 - 2800 ≤ 10 Plastic coatings Hypomer PE-8043FBLR-8086 Blocked aliphatic

polyisocyanateXylene/n-butyl acetate 74 - 76 1.05 - 1.09 －－－－ One-component PU baking paint BLR-8086

Hypomer UA-M6 Acrylic acrylate n-butyl acetate 65 - 68 1.0 －－ 1200 - 2200 － Topcoat for aluminum basecoat, Plastic coating

Hypomer UA-M6

Note

ELL017 November 2016, 500

® Registered trademark of Elementis Specialties

Inc. Before using any of our products, please

consult our Safety Data Sheets.

The information in this publication is, to the best

of our knowledge, true and accurate, but since

the conditions of use are beyond our control, no

warranty is given or to be implied in respect of

such information.

In every case, caution must be exercised to avoid

violation or infringement of statutory obligations

and any rights belonging to a third party.

We are, at all time, willing to study customers'

specific outlets involving our products in order

to enable their most effective use.

http://www.elementis-specialties-asia.com

Asia Head Office China 99, Lianyang Road, Songjiang Industrial Zone, Shanghai, China 201613 Tel: +86 21 5774 0348 Fax: +86 21 5774 3563

Taiwan 92, Kuang-Fu North Road, Hsinchu Industrial Park, Hukou, Hsinchu, Taiwan Tel: +886 3 598 4035 Fax: +886 3 598 3301

MalaysiaElementis S.E.A. (Malaysia) Sdn. Bhd. (1095769-X)

62-1, Jalan Tasik Utama 5, Medan Niaga Tasik Damai, Sungai Besi, 57000 Kuala Lumpur, Wilayah Persekutuan, MalaysiaTel: +603-9054 6690 Fax: +603-9054 6698

IndiaElementis Specialties (India) Pvt. Ltd.Unit B, Ground Floor, Jaswanti Landmark, Mehra Industrial Estate,

L.B.S Marg, Vikhroli (West), Mumbai 400 079, IndiaTel: + 91 22 67421251Fax: + 91 22 67421252

Elementis Specialties

Documents

Performance Additives and Resins for Solvent-based …elementis-specialties-asia.com/esweb_new/webprodliterature.nsf... · Performance Additives and Resins ... automotive coatings