NORME E DIRETTIVE APPLICATE DISPONIBILI AL SEGUENTE LINK: STANDARD AND DIRECTIVE APPLIED AVAILABLE AT FOLLOWING LINK:

http://www.adlerspa.com/pdf/NORME_ADLER.pdf

VALVOLE A SFERA “3 VIE CORPO PIATTO” PASSAGGIO TOTALE 90°

BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE “3 VOIES WAFER”

PASSAGE INTEGRAL 90°

KUGELHÄHNE "3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

WEB SITE: WWW.ADLERSPA.COM

CONSTRUCTION IN ACCORDING TO: ANSI B16.34 - BS EN 12516-2

ISO nbr° LRC 0160281 QMS issued by L.R.Q.A. PED nbr° COV 0212112/01 issued by L.R.V.

ATEX nbr° 40.2003.4392 issued by B.V. ISO 15848 nbr° I-148466/1-/2 issued by TÜV

On request FIRE SAFE

According to ISO 10497 “ISO-FT”

FULL BORE ACCORDING TO ISO 14313

On request S.I.L. 3

According to IEC 61508

TYPE

FT4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

VALVOLA A SFERA "3 VIE CORPO PIATTO" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES WAFER" PASSAGE INTEGRAL 90° KUGELHÄHNE “3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

• ACCOPPIAMENTO VALVOLA ATTUATORE

• CONNECTION VALVE ACTUATOR

• ACCOUPLEMENT ROBINET-ACTIONNEUR

• ZUSAMMENBAU KUGELHAHN ANTRIEB

ISO-5211 POSIZIONI OTTENIBILI OBTAINABLE POSITIONS POSITIONS OBTENABLES MÖGLICHE STELLUNGEN

CONSTRUCTION IN ACCORDING TO: ANSI B16.34 - BS EN 12516-2

TYPE

FT4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

1 CORPO BODY CORPS KÖRPER

ASTM A105 ASTM A 182 F316- A479 S31600

11 PREMIBUSSOLA PRESSING BUSH PRESSE RONDELLE STOPFBUCHSDRUCKRING

ASTM A479 S31600

2 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

12 MOLLE A TAZZA SPRING WASHERS RONDELLES BELLEVILLE TELLERFEDERN

C72/50Cr V4

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

X5CrNi17.7 or X12CrNi17.7

ON REQUEST

3* O-RING FKM (VITON)

13 VITE DI FERMO E FERMO PIN AND STOP PIN PLOT ET PLOT D’ARRET ANSCHLAGBOLZEN

UNI 3740 8.8

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

UNI 3951 A2-70

ON REQUEST

4* ANELLO SEAL ANNEAU DICHTUNGSRING

P.T.F.E.

14 DADO – CONTRODADO NUT – LOCK NUT ECROU – CONTRE-ECROU MUTTER – KONTERMUTTER

UNI 3740 - 6S

ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A479 304

ON REQUEST

5* SEDE SEAT SIEGE SITZRING

P.T.F.E.

15 LEVA WRENCH LEVIER HANDHEBEL

UNI 5946 Fe 37 ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A479 304

ON REQUEST

6 SFERA BALL BOULE KUGEL

ASTM A182 F304-A479 S30400 ASTM A351 CF8 ≥ DN 40

21 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

ASTM A182 F316-A479 S31600 ASTM A351 CF8M

7 DISPOSITIVO ANTISTATICO ANTISTATIC DEVICE CONTACT ANTISTATIQUE ANTISTATIK VORRICHTUNG

ASTM A479 S31600

22* ANELLO SEAL ANNEAU DICHTUNGSRING

P.T.F.E.

8 STELO STEM TIGE SPINDEL

ASTM A182 F304 A479 S30400

≥ DN 40

23* O-RING FKM (VITON) ASTM A182 F316 A479 S31600

9* BUSSOLA STEM SEAL JOINT TIGE UNTERE SPINDELABDICHTUNG

P.T.F.E.

24 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

10* PACCO A “V” CHEVRON RINGS JOINT A “V” 3 FACHE DACHMANSCHETTE

P.T.F.E. / GRAFITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHIT

* RICAMBI CONSIGLIATI – RECOMMENDED SPARE PARTS – PIECES DE RECHANGE CONSEILLEES – ERSATZTEIL EMPFEHLUNG

DIMENSIONI – DIMENSION – DIMENSIONS – ABMESSUNGEN DN 10 15 20 25 32 40 50 65 65 80 100 100 125 150 200

A 10 10 12 12 16 16 22 22 22 30 30 30 42

B 6 6 8 8 10 10 14 14 14 18 18 18 28

C 7 7 10 10 15 15 17 17 17 17 17 17 19

∅∅∅∅E 15 19 25 30 38 51 64 64 69 87 87 108 136

F M5 M5 M5 M5 M6 M6 M8 M8 M8 M10 M10 M10 M12

ISO F03 F03 F03 F03 F05 F05 F07 F07 F07 F10 F10 F10 F12

G 25 25 25 25 35 35 55 55 55 70 70 70 85

H 70 75 90 95 112 122 147 147 149 174 174 183 256

M 145 145 185 185 280 280 370 370 370 470 470 650 750

P 36,6 41 46 51 57 67 85 85 87 99,5 107 113 144

R 8 8 17 17 20 20 23 23 23 26 18 26 34

S 32 40 41,5 52,5 56,5 62 70 81 87 96 105 116 180

S1 97 108 115 140 150 165 185 206 216 230 262 290 370

T 36 36 36 36 50 50 70 70 70 102 102 102 125

∼∼∼∼Kg CARBON STEEL STAINLESS STEEL 4 6,5 7,5 12 15,5 18 25,5 35 54 69 90 125 200

∼∼∼∼Kg STAINLESS STEEL

3,5 5,8 6,5 11 14 16 24

• DATI E CARATTERISTICHE SOGGETTI A VARIAZIONI SENZA PREAVVISO • SPECIFICATIONS SUBJECT TO MODIFICATION WITHOUT PRIOR NOTICE • TOUS DROITS DE MODIFICATION RESERVES • KONSTRUKTIONSÄNDERUNGEN VORBEHALTEN ♣♣♣♣ ANSI 300 ON REQUEST

PN 10 ÷ 16 – ANSI 150

PN 25 ÷ 40

DN 100 ANSI 150 S=100,5 S1=240

EXECUTION 17 EXECUTION 18

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

INDICATORE DI FLUSSO FLOW INDICATOR DN 150

UNIONE CORPO LATERALE CON VITE BODY AND END ASSEMBLING WITH SCREW

-STELO ANTI ESPULSIONE -ANTI BLOW OUT STEM -TIGE ANTIEXPULSION -AUSBLASGESICHERTE

WELLE

-PACCO A “V” -CHEVRON RINGS -JOINT A “V” -3 FACHE DACHMANSCHETE ANTISTATIC DEVICE ANTISTATIK VORRICHTUNG

BS 5146

DN 150

DOPPIA TENUTA – DOUBLE SEALS DOUBLE ETACHEITE

DOPPELTE ABDICHTUNG

BREVETTO – PATENTED 00219688

-“O” RING STELO “O” RING ON STEM -TIGE AVEC “O” RING

-“O” RING IM SPINDELBEREICH

-MONTAGGIO VITI – SCREW ASSEMBLING -MONTAGE VIS – EINBAU MIT SCHRAUBEN

.

VALVOLE A SFERA “3 VIE CORPO PIATTO” PASSAGGIO TOTALE 90° - BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE “3 VOIES WAFER” PASSAGE INTEGRAL 90° - KUGELHÄHNE "3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

EXECUTION 4 - 12 EXECUTION 6 - 16

STANDARD OPTIONAL

BR

EV

ET

TO

– P

AT

EN

TE

D

00

21

96

19

TYPE

FT4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

ONLY FOR VALVES ≥ DN 80

FORO DI BILANCIAMENTO

BALANCING HOLE TROU DE BALANCEMENT

DRUCKENTLASTUNGSBOHRUNG

ON REQUEST AVAILABLE ON DN ≤ 65

AQUILA – AEGLE - AIGLE ADLER

FIRE SAFE ISO 10497 “ISO-FT”

(BS 6755 / API 607)

VALVOLE IN ACCIAIO AL CARBONIO E ACCIAOIO INOX > DN 100

CARBON STEEL BALL VALVES AND STAINLEES STEEL >DN 100

-FORO DI SCARICO NELLA SFERA -OVERPRESSURE HOLE INTO BALL

-TROU DECOMPRESSION DANS LA BOULE -ENTLASTUNGSBOHRUNG IN DER KUGEL

-DOPPIA TENUTA –DOUBLE SEALS -DOUBLE ETANCHEITE -DOPPELTE ABDICHTUNG -----------------------------------------------------------------------------------------------------------

-GHIERA A BATTUTA -METAL BEATING RING -EMBOUT AVEC BATTUE MECANIQUE

-METALLISCHER ANSCHLAG DES GEWINDEDRUCKRINGS

VALVOLE IN ACCIAIO INOX STAINLEES STEEL BALL VALVES

-PROLUNGA STELO -STEM EXTENSION -TIGE PROLONGEE -SPINDELVERLÄNGERUNG

-PARTICOLARI INOX

-STAINLESS STEEL DETAILS -ACCESSOIRES EN INOX

-EDELSTAHLTEILE

-ATTACCO “ISO” -“ISO” CONNECTIONS -SYSTEM “ISO” -ANSCHLUSS “ISO”

-SFERA CONTENUTA –CONTENTS BALL - BOULE CONTENUE

-NICHT RAUSRAGENDE KUGEL

- SERVIZIO CRIOGENICO – CRYOGENIC SERVICE - SERVICE CRYOGÉNIQUE

- TIEFTEMPERATUR SERVICE

-FIRE SAFE ISO FT + “O” RING STELO -FIRE SAFE ISO FT + “O” RING ON STEM

-SECURITE FEU ISO FT + TIGE AVEC “O” RING -FEUERSICHERE AUSFÜHRUNG ISO FT +

“O” RING IM SPINDELBEREICH

VALVOLE A SFERA "3 VIE" PASSAGGIO TOTALE 90°

BALL VALVES "3 VIE" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90°

KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

DN

15

÷ 6

5 P

N 1

0 ÷

16

TYPE

FT4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

VITI D’ASSEMBLAGGIO PER FT4 ASSEMBLING SCREWS FOR FT4 VIS D’ASSEMBLAGE POUR FT4 MONTAGESCHRAUBEN FÜR FT4

N° VITI – DIMENSIONE ● N° SCREW – DIMENSIONS ● N° VIS- DIMENSIONS ● N° SCHRAUBEN – ABMESSUNGEN

EUROPEAN NORM

DN PN

10-15 20 25 32 40 50 65 80 100 125 150 200 250

10 12 M12 X30

12 M12 X30

12 M12 X30

12 M16 X35

12 M16 X35

12 M16 X40

12 M16 X40

* 24

M16 X40

24 M16 X40

24 M16 X45

24 M20 X45

24 M20 X50

16 12 M12 X30

12 M12 X30

12 M12 X30

12 M16 X35

12 M16 X35

12 M16 X40

12 M16 X40

24 M16 X40

24 M16 X40

24 M16 X45

24 M20 X45

36 M20 X50

25 12 M12 X30

12 M12 X35

12 M12 X35

12 M16 X40

12 M16

X40 12 M16

X40 24 M16

X45 24 M16

X45 24 M20

X50 24 M24

X55 24 M24

X55 36 M24

X60

40 12 M12

X30 12 M12

X35 12 M12

X35 12 M16

X40 12 M16

X40 12 M16

X40 24 M16

X45 24 M16

X45 24 M20

X50 24 M24

X55 24 M24

X55 36 M27

X65

* N° 8 per UNI 2223/2229

ANSI METRIC (STANDARD ADLER)

Ø

Rating ½” ¾” 1” 1 ¼” 1 ½” 2” 2 ½” 3” 4” 5” 6” 8”

150 12 M14 X30

12 M14 X30

12 M14 X30

12 M14 X45

12 M14 X35

12 M16 X40

12 M16 X40

12 M16 X45

24 M16 X45

24 M20 X50

24 M20 X50

24 M20 X50

300 12 M14 X30

12 M16 X30

12 316 X35

12 M16 X40

12 M20 X45

24 M16 X40

24 M20 X50

24 M20 X50

24 M20 X55

24 M20 X60

36 M20 X60

36 M24 X70

ANSI B1.1 UNC (ON REQUEST)

Ø

Rating ½” ¾” 1” 1 ¼” 1 ½” 2” 2 ½” 3” 4” 5” 6” 8”

150 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 1/2 12 5/8

X 1 1/2 12 5/8

X 1 3/4 12 5/8

X 1 3/4 24 5/8

X 1 3/4 24 3/4

X 2 24 3/4

X 2 24 3/4

X 2

300 12 1/2

X 1 ¼ 12 5/8

X 1 1/4 12 5/8

X 1 1/2 12 5/8

X 1 1/2 12 3/4

X 1 3/4 12 5/8

X 1 3/4 24 3/4

X 2 24 3/4

X 2 24 3/4

X 2 1/4 24 3/4

X 2 1/4 36 3/4

X 2 1/4 23 7/8

X2 3/4

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

NORME E DIRETTIVE APPLICATE DISPONIBILI AL SEGUENTE LINK:

STANDARD AND DIRECTIVE APPLIED AVAILABLE AT FOLLOWING LINK: http://www.adlerspa.com/pdf/NORME_ADLER.pdf

VALVOLE A SFERA “3 VIE CORPO PIATTO” PASSAGGIO TOTALE 90°

BALL VALVES "3 WAY WAFER" FULL BORE 90° ROBINETS A BOISSEAU SPHERIQUE

“3 VOIES WAFER” PASSAGE INTEGRAL 90°

KUGELHÄHNE "3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

WEB SITE: WWW.ADLERSPA.COM

CONSTRUCTION IN ACCORDING TO: ANSI B 16.34 - BS EN 12516-2

ISO nbr° LRC 0160281 QMS issued by L.R.Q.A. PED nbr° COV 0212112/01 issued by L.R.V.

ATEX nbr° 40.2003.4392 issued by B.V. ISO 15848 nbr° I-148466/1-/2 issued by TÜV

On request FIRE SAFE

According to ISO 10497 “ISO-FT”

On request S.I.L. 3

According to IEC 61508

FULL BORE ACCORDING TO ISO 14313

TYPE

FZ4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

VALVOLA A SFERA "3 VIE CORPO PIATTO" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES WAFER" PASSAGE INTEGRAL 90° KUGELHÄHNE “3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

• ACCOPPIAMENTO VALVOLA ATTUATORE

• CONNECTION VALVE ACTUATOR

• ACCOUPLEMENT ROBINET-ACTIONNEUR

• ZUSAMMENBAU KUGELHAHN ANTRIEB

ISO-5211 POSIZIONI OTTENIBILI OBTAINABLE POSITIONS POSITIONS OBTENABLES MÖGLICHE STELLUNGEN

CONSTRUCTION IN ACCORDING TO: ANSI B 16.34 - BS EN 12516-2

TYPE

FZ4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

1 CORPO BODY CORPS KÖRPER

ASTM A105 ASTM A 182 F316- A479 S31600

9* BUSSOLA STEM SEAL JOINT TIGE UNTERE SPINDELABDICHTUNG

P.T.F.E.

2 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

10* PACCO A “V” CHEVRON RINGS JOINT A “V” 3 FACHE DACHMANSCHETTE

P.T.F.E. / GRAFITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHIT

3* O-RING FKM (VITON)

11 PREMIBUSSOLA

PRESSING BUSH PRESSE RONDELLE STOPFBUCHSDRUCKRING

ASTM A479 S31600

4* ANELLO SEAL ANNEAU DICHTUNGSRING

P.T.F.E.

12 MOLLE A TAZZA SPRING WASHERS RONDELLES BELLEVILLE TELLERFEDERN

C72/50Cr V4

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

X5CrNi17.7 or X12CrNi17.7

ON REQUEST

5* SEDE SEAT SIEGE SITZRING

R.P.T.F.E.

13 VITE DI FERMO E FERMO PIN AND STOP PIN PLOT E PLOT D’ARRET ANSCHLAGBOLZEN

UNI 3740 8.8

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

UNI 3951 A2-70

ON REQUEST

6 SFERA BALL BOULE KUGEL

ASTM A182 F304-A479 S30400 ASTM A351 CF8 ≥ DN 40

14 UNI 3740 - 6S ASTM A479 304

ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A182 F316-A479 S31600 ASTM A351 CF8M ON REQUEST

7 DISPOSITIVO ANTISTATICO ANTISTATIC DEVICE CONTACT ANTISTATIQUE ANTISTATIK VORRICHTUNG

ASTM A479 S31600

15 LEVA WRENCH LEVIER HANDHEBEL

UNI 5946 Fe 37 ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A479 304

ON REQUEST

8 STELO STEM TIGE SPINDEL

ASTM A182 F304 A479 S30400

≥ DN 40

16 ASTM A182 F316 A479 S31600

* RICAMBI CONSIGLIATI – RECOMMENDED SPARE PARTS – PIECES DE RECHANGE CONSEILLEES – ERSATZTEIL EMPFEHLUNG

DIMENSIONI – DIMENSION – DIMENSIONS – ABMESSUNGEN

DN 10 15 20 25 32 40 50 65 65 80 100 100 125 150 200

A 10 10 12 12 16 16 22 22 22 30 30 30 42

B 6 6 8 8 10 10 14 14 14 18 18 18 28

C 7 7 10 10 15 15 17 17 17 17 17 17 19

∅∅∅∅E 15 19 25 30 38 51 64 64 76 98 98 115 150

F M5 M5 M5 M5 M6 M6 M8 M8 M8 M10 M10 M10 M12

ISO F03 F03 F03 F03 F05 F05 F07 F07 F07 F10 F10 F10 F12

G 25 25 25 25 35 35 55 55 55 70 70 70 85

H 70 75 90 95 112 122 147 147 149 174 174 183 256

M 145 145 185 185 280 280 370 370 370 470 470 650 750

P 36,6 41 46 51 57 67 85 85 87 99,5 107 113 144

R 8 8 17 17 20 20 23 23 23 26 18 26 34

S 32 40 41,5 52,5 56,5 62 70 81 87 96 106 116 153

S1 97 108 115 140 150 165 185 206 216 230 262 290 350

T 36 36 36 36 50 50 70 70 70 102 102 102 125

∼∼∼∼Kg CARBON STEEL STAINLESS STEEL 4 6,5 7,5 12 15,5 18 25,5 35 54 69 90 125 180

∼∼∼∼Kg STAINLESS STEEL

3,5 5,8 6,5 11 14 16 24

• DATI E CARATTERISTICHE SOGGETTI A VARIAZIONI SENZA PREAVVISO • SPECIFICATIONS SUBJECT TO MODIFICATION WITHOUT PRIOR NOTICE • TOUS DROITS DE MODIFICATION RESERVES • KONSTRUKTIONSÄNDERUNGEN VORBEHALTEN ♣♣♣♣ ANSI 300 ON REQUEST

PN 10 ÷ 16 – ANSI 150

PN 25 ÷ 40

DN 100 ANSI 150 S=100,5 S1=240

EXECUTION 17 EXECUTION 18

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

INDICATORE DI FLUSSO FLOW INDICATOR

DN 150 UNIONE CORPO LATERALE CON VITE

BODY AND END ASSEMBLING WITH SCREW

-STELO ANTI ESPULSIONE -ANTI BLOW OUT STEM -TIGE ANTIEXPULSION -AUSBLASGESICHERTE

WELLE

-PACCO A “V” -CHEVRON RINGS -JOINT A “V” -3 FACHE DACHMANSCHETE ANTISTATIC DEVICE ANTISTATIK VORRICHTUNG

BS 5146

DN 150

DOPPIA TENUTA – DOUBLE SEALS DOUBLE ETACHEITE

DOPPELTE ABDICHTUNG

BREVETTO – PATENTED 00219688

-“O” RING STELO “O” RING ON STEM -TIGE AVEC “O” RING

-“O” RING IM SPINDELBEREICH

-MONTAGGIO VITI – SCREW ASSEMBLING -MONTAGE VIS – EINBAU MIT SCHRAUBEN

VALVOLE A SFERA “3 VIE CORPO PIATTO” PASSAGGIO TOTALE 90° - BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE “3 VOIES WAFER” PASSAGE INTEGRAL 90° - KUGELHÄHNE "3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

EXECUTION 4 - 12 EXECUTION 6 - 16

STANDARD OPTIONAL

BR

EV

ET

TO

– P

AT

EN

TE

D

00

21

96

19

-

TYPE

FZ4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

ONLY FOR VALVES ≥ DN 50

FORO DI BILANCIAMENTO

BALANCING HOLE TROU DE BALANCEMENT

DRUCKENTLASTUNGSBOHRUNG

ON REQUEST AVAILABLE ON DN ≤ 40

-TENUTE INTEGRALE -POCKETLESS SEATS -TENUE INTEGRALE -TOTRAUMARM

-P.T.F.E. / R.T.F.E.

FIRE SAFE ISO 10497 “ISO-FT” (BS 6755 / API 607)

VALVOLE IN ACCIAIO AL CARBONIO E ACCIAIO INOX ≥ DN 80

CARBON STEEL BALL VALVES AND STAINLEES STEEL ≥ DN 80

ADLER COMPANY

-DOPPIA TENUTA –DOUBLE SEALS -DOUBLE ETANCHEITE -DOPPELTE ABDICHTUNG -----------------------------------------------------------------------------------------------------------

-GHIERA A BATTUTA -METAL BEATING RING -EMBOUT AVEC BATTUE MECANIQUE

-METALLISCHER ANSCHLAG DES GEWINDEDRUCKRINGS

VALVOLE IN ACCIAIO INOX STAINLEES STEEL BALL VALVES

-PROLUNGA STELO -STEM EXTENSION -TIGE PROLONGEE -SPINDELVERLÄNGERUNG

-PARTICOLARI INOX

-STAINLESS STEEL DETAILS -ACCESSOIRES EN INOX

-EDELSTAHLTEILE

-ATTACCO “ISO” -“ISO” CONNECTIONS -SYSTEM “ISO” -ANSCHLUSS “ISO”

-SFERA CONTENUTA –CONTENTS BALL - BOULE CONTENUE

-NICHT RAUSRAGENDE KUGEL

- SERVIZIO CRIOGENICO – CRYOGENIC SERVICE - SERVICE CRYOGÉNIQUE

- TIEFTEMPERATUR SERVICE

-FIRE SAFE ISO FT + “O” RING STELO -FIRE SAFE ISO FT + “O” RING ON STEM

-SECURITE FEU ISO FT + TIGE AVEC “O” RING -FEUERSICHERE AUSFÜHRUNG ISO FT +

“O” RING IM SPINDELBEREICH

VALVOLE A SFERA “3 VIE CORPO PIATTO” PASSAGGIO TOTALE 90° - BALL VALVES "3 WAY WAFER" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE “3 VOIES WAFER” PASSAGE INTEGRAL 90° - KUGELHÄHNE "3 WEGE KOMPAKTHAHN" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

DN

15

÷ 6

5

PN

16 ÷

10

TYPE

FZ4 PN 10 ÷ 40

ANSI 150 ÷ 300*

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V. FIRE SAFE EXECUTION by L.R.

ISO 15848 by TÜV ANTISTATIC DEVICE by L.R.

FIRE SAFE TESTED ISO 10497 by L.R.

VITI D’ASSEMBLAGGIO PER FZ4 ASSEMBLING SCREWS FOR FZ4 VIS D’ASSEMBLAGE POUR FZ4 MONTAGESCHRAUBEN FÜR FZ4

N° VITI – DIMENSIONE ● N° SCREW – DIMENSIONS ● N° VIS- DIMENSIONS ● N° SCHRAUBEN–ABMESSUNGEN

EUROPEAN NORM

DN PN

10-15 20 25 32 40 50 65 80 100 125 150 200 250

10 12 M12 X30

12 M12 X30

12 M12 X30

12 M16 X35

12 M16 X35

12 M16 X40

12 M16 X40

* 24

M16 X40

24 M16 X40

24 M16 X45

24 M20 X45

24 M20 X50

16 12 M12 X30

12 M12 X30

12 M12 X30

12 M16 X35

12 M16 X35

12 M16 X40

12 M16 X40

24 M16 X40

24 M16 X40

24 M16 X45

24 M20 X45

36 M20 X50

25 12 M12 X30

12 M12 X35

12 M12 X35

12 M16 X40

12 M16

X40 12 M16

X40 24 M16

X45 24 M16

X45 24 M20

X50 24 M24

X55 24 M24

X55 36 M24

X60

40 12 M12

X30 12 M12

X35 12 M12

X35 12 M16

X40 12 M16

X40 12 M16

X40 24 M16

X45 24 M16

X45 24 M20

X50 24 M24

X55 24 M24

X55 36 M27

X65

* N° 8 per UNI 2223/2229

ANSI METRIC (STANDARD ADLER)

Ø

Rating ½” ¾” 1” 1 ¼” 1 ½” 2” 2 ½” 3” 4” 5” 6” 8”

150 12 M14 X30

12 M14 X30

12 M14 X30

12 M14 X45

12 M14 X35

12 M16 X40

12 M16 X40

12 M16 X45

24 M16 X45

24 M20 X50

24 M20 X50

24 M20 X50

300 12 M14 X30

12 M16 X30

12 316 X35

12 M16 X40

12 M20 X45

24 M16 X40

24 M20 X50

24 M20 X50

24 M20 X55

24 M20 X60

36 M20 X60

36 M24 X70

ANSI B1.1 UNC (ON REQUEST)

Ø

Rating ½” ¾” 1” 1 ¼” 1 ½” 2” 2 ½” 3” 4” 5” 6” 8”

150 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 ¼ 12 1/2

X 1 1/2 12 5/8

X 1 1/2 12 5/8

X 1 3/4 12 5/8

X 1 3/4 24 5/8

X 1 3/4 24 3/4

X 2 24 3/4

X 2 24 3/4

X 2

300 12 1/2

X 1 ¼ 12 5/8

X 1 1/4 12 5/8

X 1 1/2 12 5/8

X 1 1/2 12 3/4

X 1 3/4 12 5/8

X 1 3/4 24 3/4

X 2 24 3/4

X 2 24 3/4

X 2 1/4 24 3/4

X 2 1/4 36 3/4

X 2 1/4 23 7/8

X2 3/4

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

NORME E DIRETTIVE APPLICATE DISPONIBILI AL SEGUENTE LINK: STANDARD AND DIRECTIVE APPLIED AVAILABLE AT FOLLOWING LINK:

http://www.adlerspa.com/pdf/NORME_ADLER.pdf

VALVOLE A SFERA “3 VIE” PASSAGGIO TOTALE 90°

BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE

"3 VOIES" PASSAGE INTEGRAL 90°

KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

WEB SITE: WWW.ADLERSPA.COM

CONSTRUCTION IN ACCORDING TO: DIN 3202 M3 – ANSI B 16.34

ISO 14313

ISO nbr° LRC 0160281 QMS issued by L.R.Q.A. PED nbr° COV 0212112/01 issued by L.R.V. ATEX nbr° 40.2003.4392 issued by B.V. ISO 15848 nbr° I-148466/1-/2 issued by TÜV

On request FIRE SAFE

According to ISO 10497 “ISO-FT”

FULL BORE ACCORDING TO ISO 14313

On request S.I.L. 3

According to IEC 61508

TYPE

FT6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

VALVOLA A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

• ACCOPPIAMENTO VALVOLA ATTUATORE

• CONNECTION VALVE ACTUATOR

• ACCOUPLEMENT ROBINET-ACTIONNEUR

• ZUSAMMENBAU KUGELHAHN ANTRIEB

ISO-5211 POSIZIONI OTTENIBILI OBTAINABLE POSITIONS POSITIONS OBTENIBLES MÖGLICHE STELLUNGEN

CONSTRUCTION IN ACCORDING TO: DIN 3202 M3 - ANSI B16.34

ISO 14313

TYPE

FT6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

1 CORPO BODY CORPS KÖRPER

ASTM A105 ASTM A 182 F316- A479 S31600

11 PREMIBUSSOLA PRESSING BUSH PRESSE RONDELLE STOPFBUCHSDRUCKRING

ASTM A479 S31600

2 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

12 MOLLE A TAZZA SPRING WASHERS RONDELLES BELLEVILLE TELLERFEDERN

C72/50Cr V4

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

X5CrNi17.7 or X12CrNi17.7

ON REQUEST

4* ANELLO

SEAL ANNEAU DICHTUNGSRING

P.T.F.E.

13 VITE DI FERMO E FERMO PIN AND STOP PIN PLOT ET PLOT D’ARRET ANSCHLAGBOLZEN

UNI 3740 8.8

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

UNI 3951 A2-70

ON REQUEST

5* SEDE SEAT SIEGE SITZRING

P.T.F.E.

14 DADO – CONTRODADO NUT – LOCK NUT ECROU – CONTRE-ECROU MUTTER – KONTERMUTTER

UNI 3740 - 6S

ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A479 304

ON REQUEST

6 SFERA BALL BOULE KUGEL

ASTM A182 F304-A479 S30400 ASTM A351 CF8 ≥ ∅ 1½”

15 UNI 5946 Fe 37 ASTM A479 304

UNI 5946 Fe 37 ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A182 F316-A479 S31600 ASTM A351 CF8M

ASTM A479 304

ON REQUEST

7 DISPOSITIVO ANTISTATICO ANTISTATIC DEVICE CONTACT ANTISTATIQUE ANTISTATIK VORRICHTUNG

ASTM A479 S31600

21 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

8 STELO STEM TIGE SPINDEL

ASTM A182 F304 A479 S30400

≥ ∅ 1½”

22* ANELLO SEAL ANNEAU DICHTUNGSRING

P.T.F.E. ASTM A182 F316 A479 S31600

9* BUSSOLA STEM SEAL JOINT TIGE UNTERE SPINDELABDICHTUNG

P.T.F.E.

24 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

10* PACCO A “V” CHEVRON RINGS JOINT A “V”

3 FACHE DACHMANSCHETTE

P.T.F.E. / GRAFITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHIT

* RICAMBI CONSIGLIATI – RECOMMENDED SPARE PARTS – PIECES DE RECHANGE CONSEILLEES – ERSATZTEIL EMPFEHLUNG

DIMENSIONI – DIMENSION – DIMENSIONS – ABMESSUNGEN ∅∅∅∅” ¼” ⅜” ½” ¾” 1” 1¼” 1½” 2” 2½” 3” 4” 5” 6” 8” A 8 8 10 10 12 12 16 16

B 5 5 6 6 8 8 10 12

C 6 6 7 7 10 10 15 15

∅∅∅∅E 10 10 15 19 25 30 38 51

F M5 M5 M5 M5 M5 M5 M6 M6

ISO F03 F03 F03 F03 F03 F03 F05 F05

G 25 25 25 25 25 25 35 35

H 50 50 70 74 90 97 113 123

L 24,5 24,5 30 32,5 39 43,5 51,5 60,5

M 120 120 145 145 185 185 280 280

P 21,5 21,5 30 34,5 46 51 57 67

R 12 12 14 14 17 17 20 20

S 60 60 75 80 90 110 120 140

T 36 36 36 36 36 36 50 50

PN 63 63 63 40 40 40 25 25

∼∼∼∼Kg 1,5 1,5 2,3 3,1 4,4 6,2 9,5 15 CARBON STEEL – STAINLESS STEEL

∼∼∼∼Kg 2 4 8,8 STAINLESS STEEL

• DATI E CARATTERISTICHE SOGGETTI A VARIAZIONI SENZA PREAVVISO • SPECIFICATIONS SUBJECT TO MODIFICATION WITHOUT PRIOR NOTICE • TOUS DROITS DE MODIFICATION RESERVES • KONSTRUKTIONSÄNDERUNGEN VORBEHALTEN

EXECUTION 17

EXECUTION 18

Ø ¼”÷⅜” SEAT IN R.P.T.F.E.

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

INDICATORE DI FLUSSO FLOW INDICATOR ADLER

UNA GAMMA COMPLETA

PRIVILEGIANDO LA QUALITA’

A COMPLETE RANGE PRIVILEGING THE QUALITY

-STELO ANTI ESPULSIONE -ANTI BLOW OUT STEM -TIGE ANTIEXPULSION -AUSBLASGESICHERTE

WELLE

-PACCO A “V” -CHEVRON RINGS -JOINT A “V” -3 FACHE DACHMANSCHETE ANTISTATIC DEVICE ANTISTATIK VORRICHTUNG

BS 5146

BREVETTO – PATENTED 00219688

-“O” RING STELO “O” RING ON STEM -TIGE AVEC “O” RING

-“O” RING IM SPINDELBEREICH

SEE TABLE 23 FOR TYPE

OF THREAD

-MANIGLIA OVALE - OVAL HANDLE -LEVIER OVAL –HANDHEBEL IN OVALFORM

VALVOLE A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 VIE" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

EXECUTION 4 -12 EXECUTION 6 - 16

STANDARD OPTIONAL

∅ ½

” ÷

2”

TYPE

FT6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

ONLY FOR VALVES ≥ DN 50

FORO DI BILANCIAMENTO

BALANCING HOLE TROU DE BALANCEMENT

DRUCKENTLASTUNGSBOHRUNG

ON REQUEST AVAILABLE ON DN ≤ 40

AQUILA – EAGLE – AIGLE ADLER

FIRE SAFE ISO 10497 “ISO-FT” (BS 6755 / API 607)

VALVOLE IN ACCIAIO AL CARBONIO

CARBON STEEL BALL VALVES

-FORO DI SCARICO NELLA SFERA -OVERPRESSURE HOLE INTO BALL

-TROU DECOMPRESSION DANS LA BOULE -ENTLASTUNGSBOHRUNG IN DER KUGEL

-ANELLO CONTENUTO –CONTAINED SEAL -ANNEAU CONTENU -DICHTRING GEKAMMERT -----------------------------------------------------------------------------------------------------------

-GHIERA A BATTUTA -METAL BEATING RING -EMBOUT AVEC BATTUE MECANIQUE

-METALLISCHER ANSCHLAG DES GEWINDEDRUCKRINGS

VALVOLE IN ACCIAIO INOX STAINLEES STEEL BALL VALVES

-PROLUNGA STELO -STEM EXTENSION -TIGE PROLONGEE -SPINDELVERLÄNGERUNG

-PARTICOLARI INOX

-STAINLESS STEEL DETAILS -ACCESSOIRES EN INOX

-EDELSTAHLTEILE

-ATTACCO “ISO” -“ISO” CONNECTIONS -SYSTEM “ISO” -ANSCHLSS “ISO”

-SFERA CONTENUTA –CONTENTS BALL - BOULE CONTENUE

-NICHT RAUSRAGENDE KUGEL

- SERVIZIO CRIOGENICO – CRYOGENIC SERVICE - SERVICE CRYOGÉNIQUE

- TIEFTEMPERATUR SERVICE

CE

RT

IFY

IS

O 9

00

1:2

008

VALVOLE A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 VIE" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ BESCHREIBUNG

∅ ½

”-1”

-1½

”

VA

LV

OL

E I

N A

CC

IAIO

IN

OX

ST

AIN

LE

SS

ST

EE

L B

AL

L V

AL

VE

S

∅ ¼

”-⅜

”-¾

”- 1

¼”-

2”

TYPE

FT6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

CARATTERISTICHE DEL FILETTO THREAD FEATURES FILETAGES CARACTÉRISTIQUES GEWINDE KENNDATEN

IN ACCORDANCE TO ISO 7-1 – 1994

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Des

igna

tion

of

thre

ad s

ize

Num

ber

of th

read

s in

25.

4 m

m

Pit

ch

Hei

ght o

f th

read

Diameters of gauges plane

Gauges length (external threads)

Tolerance on position of

gauge plan on internal thread

Length of useful external thread not

less than

Fitting

allowance

Dia

met

er to

lera

nce

on

para

llel

inte

rnal

thre

ads

Maj

or

Pit

ch

Min

or

Nom

inal

Tolerance ±t1/2

Max

.

Min

.

For

nom

inal

g

auge

leng

th

For

max

imum

ga

uge

leng

th

For

min

imum

ga

uge

leng

th

Tolerance ±t1/2

2)

Tur

ns o

f th

read

2)

Tur

ns o

f th

read

2)

Tur

ns o

f th

read

P h d d2 d1

¼ 19 1,337 0,856 13,15 12,30 11,44 6 1,3 1 7,3 4,7 1,7 1 ¼ 9,7 11 8,4 3,7 2 ¾ ±0,104 3/8 19 1,337 0,856 16,66 15,80 14,95 6,4 1,3 1 7,7 5,1 1,7 1 ¼ 10,1 11,4 8,8 3,7 2 ¾ ±0,104 ½ 14 1,814 1,162 20,95 19,79 18,63 8,2 1,8 1 10 6,4 2,3 1 ¼ 13,2 15 11,4 5 2 ¾ ±0,142 ¾ 14 1,814 1,162 26,44 25,27 24,11 9,5 1,8 1 11,3 7,7 2,3 1 ¼ 14,5 16,3 12,7 5 2 ¾ ±0,142 1 11 2,309 1,479 33,24 31,77 30,29 10,4 2,3 1 12,7 8,1 2,9 1 ¼ 16,8 19,1 14,5 6,4 2 ¾ ±0,180

1 ¼ 11 2,309 1,479 41,91 40,43 38,95 12,7 2,3 1 15 10,4 2,9 1 ¼ 19,1 21,4 16,8 6,4 2 ¾ ±0,180 1 ½ 11 2,309 1,479 47,80 46,32 44,84 12,7 2,3 1 15 10,4 2,9 1 ¼ 19,1 21,4 16,8 6,4 2 ¾ ±0,180

2 11 2,309 1,479 59,61 58,13 56,65 15,9 2,3 1 18,2 13,6 2,9 1 ¼ 23,4 25,7 21,1 7,5 3 ¼ ±0,180

IN ACCORDANCE TO ANSI B1.20.1 – 1983

1 2 3 4 5 6 7 8 9 10 11

Nominal

Pipe Size

O.D. of

Pipe (D) T

hrea

ds/i

nch

(n)

Pitch of threads

(P)

Pitch diam. at beginning of external thread (E0)

Handtight engagement Effective thread, external

Length2 (L1) Diam.3

(E1) Length4 (L2) Diam.5

(E2) inch threads inch threads

¼ 0,540 18 0,05556 0,47739 0,2278 4,1 0,49163 0,4018 723 0,50250 3/8 0,675 18 0,05556 0,61201 0,240 4,32 0,32701 0,4078 734 0,63750 ½ 0,840 14 0,07143 0,75843 0,320 4,48 0,77843 0,5337 747 0,79179 ¾ 1,050 14 0,07143 0,96768 0,339 4,75 0,98887 0,5457 764 1,00179 1 1,315 11,5 0,0896 1,21363 0,400 4,6 1,23863 0,6828 785 1,25630

1 ¼ 1,660 11,5 0,0896 1,55713 0,420 4,83 1,58338 0,7068 813 1,60130 1 ½ 1,900 11,5 0,0896 1,79609 0,420 4,83 1,82237 0,7235 832 1,84130

2 2,375 11,5 0,0896 2,26902 0,436 5,01 2,29627 0,7565 870 2,31630 ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

NORME E DIRETTIVE APPLICATE DISPONIBILI AL SEGUENTE LINK: STANDARD AND DIRECTIVE APPLIED AVAILABLE AT FOLLOWING LINK:

http://www.adlerspa.com/pdf/NORME_ADLER.pdf

VALVOLE A SFERA “3 VIE” PASSAGGIO TOTALE 90°

BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90°

KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

WEB SITE: WWW.ADLERSPA.COM

CONSTRUCTION IN ACCORDING TO: DIN 3202 M3 – ANSI B 16.34

ISO 14313

ISO nbr° LRC 0160281 QMS issued by L.R.Q.A. PED nbr° COV 0212112/01 issued by L.R.V. ATEX nbr° 40.2003.4392 issued by B.V. ISO 15848 nbr° I-148466/1-/2 issued by TÜV

On request FIRE SAFE

According to ISO 10497 “ISO-FT”

On request S.I.L. 3

According to IEC 61508

FULL BORE ACCORDING TO ISO 14313

TYPE

FZ6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

VALVOLA A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

• ACCOPPIAMENTO VALVOLA ATTUATORE

• CONNECTION VALVE ACTUATOR

• ACCOUPLEMENT ROBINET-ACTIONNEUR

• ZUSAMMENBAU KUGELHAHN ANTRIEB

ISO-5211 POSIZIONI OTTENIBILI OBTAINABLE POSITIONS POSITIONS OBTENABLES MÖGLICHE STELLUNGEN

CONSTRUCTION IN ACCORDING TO: DIN 3202 M3 – ANSI 16.34

ISO 14313

TYPE

FZ6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

N. DESCRIZIONE DESCRIPTION DESCRIPTION BESCHREIBUNG

MATERIALI MATERIALS MATERIAUX WERKSTOFFE

1 CORPO BODY CORPS KÖRPER

ASTM A105 ASTM A 182 F316- A479 S31600

9* BUSSOLA STEM SEAL JOINT TIGE UNTERE SPINDELABDICHTUNG

P.T.F.E.

2 GHIERA INSERT EMBOUT GEWINDEDRUCKRING

ASTM A105 ASTM A 182 F316- A479 S31600

10* PACCO A “V” CHEVRON RINGS JOINT A “V” 3 FACHE DACHMANSCHETTE

P.T.F.E. / GRAFITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHITE P.T.F.E. / GRAPHIT

11 PREMIBUSSOLA PRESSING BUSH PRESSE RONDELLE STOPFBUCHSDRUCKRING

ASTM A479 S31600

4* ANELLO SEAL ANNEAU DICHTUNGSRING

P.T.F.E.

12 MOLLE A TAZZA SPRING WASHERS RONDELLES BELLEVILLE TELLERFEDERN

C72/50Cr V4

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

X5CrNi17.7 or X12CrNi17.7

ON REQUEST

5* SEDE SEAT SIEGE SITZRING

P.T.F.E.

13 VITE DI FERMO E FERMO PIN AND STOP PIN PLOT ET PLOT D’ARRET ANSCHLAGBOLZEN

UNI 3740 8.8

ZINCATO – GALVANIZED - ZINGUE – VERZINKT

UNI 3951 A2-70

ON REQUEST

6 SFERA BALL BOULE KUGEL

ASTM A182 F304-A479 S30400 ASTM A351 CF8 ≥ ∅ 1½”

14 UNI 3740 - 6S ASTM A479 304

ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A182 F316-A479 S31600 ASTM A351 CF8M ON REQUEST

7 DISPOSITIVO ANTISTATICO ANTISTATIC DEVICE CONTACT ANTISTATIQUE ANTISTATIK VORRICHTUNG

ASTM A479 S31600

15 LEVA WRENCH LEVIER HANDHEBEL

UNI 5946 Fe 37 ZINCATO – GALVANIZED ZINGUE – VERZINKT

ASTM A479 304

ON REQUEST

8 STELO STEM TIGE SPINDEL

ASTM A182 F304 A479 S30400

≥ ∅ 1½”

16 ASTM A182 F316 A479 S31600

* RICAMBI CONSIGLIATI – RECOMMENDED SPARE PARTS – PIECES DE RECHANGE CONSEILLEES – ERSATZTEIL EMPFEHLUNG

DIMENSIONI – DIMENSION – DIMENSIONS – ABMESSUNGEN

∅∅∅∅” ¼” ⅜” ½” ¾” 1” 1¼” 1½” 2” 2½” 3” 4” 5” 6” 8” A 8 8 10 10 12 12 16 16

B 5 5 6 6 8 8 10 12

C 6 6 7 7 10 10 15 15

∅∅∅∅E 10 10 15 19 25 30 38 51

F M5 M5 M5 M5 M5 M5 M6 M6

ISO F03 F03 F03 F03 F03 F03 F05 F05

G 25 25 25 25 25 25 35 35

H 50 50 70 74 90 97 113 123

L 32 32 39,5 42 49,5 59,5 64,5 77

M 120 120 145 145 185 185 280 280

P 21,5 21,5 30 34,5 46 51 57 67

R 12 12 14 14 17 17 20 20

S 60 60 75 80 90 110 120 140

T 36 36 36 36 36 36 50 50

PN 63 63 63 40 40 40 25 25

∼∼∼∼Kg 1,5 1,5 2,3 3,1 4,4 6,2 9,5 15 CARBON STEEL – STAINLESS STEEL

∼∼∼∼Kg 2 4 8,8 STAINLESS STEEL

• DATI E CARATTERISTICHE SOGGETTI A VARIAZIONI SENZA PREAVVISO • SPECIFICATIONS SUBJECT TO MODIFICATION WITHOUT PRIOR NOTICE • TOUS DROITS DE MODIFICATION RESERVES • KONSTRUKTIONSÄNDERUNGEN VORBEHALTEN

EXECUTION 17

EXECUTION 18

Ø ¼”÷⅜” SEAT IN R.P.T.F.E.

ADLER SpA – BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com

INDICATORE DI FLUSSO FLOW INDICATOR

-STELO ANTI ESPULSIONE -ANTI BLOW OUT STEM -TIGE ANTIEXPULSION -AUSBLASGESICHERTE

WELLE

-PACCO A “V” -CHEVRON RINGS -JOINT A “V” -3 FACHE DACHMANSCHETE ANTISTATIC DEVICE ANTISTATIK VORRICHTUNG

BS 5146

BREVETTO – PATENTED 00219688

-“O” RING STELO “O” RING ON STEM -TIGE AVEC “O” RING

-“O” RING IM SPINDELBEREICH

SEE TABLE 23 FOR TYPE

OF THREAD

-MANIGLIA OVALE - OVAL HANDLE -LEVIER OVAL –HANDHEBEL IN OVALFORM

VALVOLA A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

EXECUTION 4 -12 EXECUTION6 - 16

STANDARD OPTIONAL

∅ ½

” ÷

2”

TYPE

FZ6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

ONLY FOR VALVES ≥ DN 50

FORO DI BILANCIAMENTO

BALANCING HOLE TROU DE BALANCEMENT

DRUCKENTLASTUNGSBOHRUNG

ON REQUEST AVAILABLE ON DN ≤ 40

-TENUTE INTEGRALE -POCKETLESS SEATS -TENUE INTEGRALE -TOTRAUMARM

-P.T.F.E. / R.T.F.E.

FIRE SAFE ISO 10497 “ISO-FT” (BS 6755 / API 607)

VALVOLE IN ACCIAIO AL CARBONIO CARBON STEEL BALL VALVES

AQUILA – EAGLE – AIGLE

ADLER

-ANELLO CONTENUTO –CONTAINED SEAL -ANNEAU CONTENU -DICHTRING GEKAMMERT -----------------------------------------------------------------------------------------------------------

-GHIERA A BATTUTA -METAL BEATING RING -EMBOUT AVEC BATTUE MECANIQUE

-METALLISCHER ANSCHLAG DES GEWINDEDRUCKRINGS

VALVOLE IN ACCIAIO INOX

STAINLEES STEEL BALL VALVES

-PROLUNGA STELO -STEM EXTENSION -TIGE PROLONGEE -SPINDELVERLÄNGERUNG

-PARTICOLARI INOX

-STAINLESS STEEL DETAILS -ACCESSOIRES EN INOX

-EDELSTAHLTEILE

-ATTACCO “ISO” -“ISO” CONNECTIONS -SYSTEM “ISO” -ANSCHLUSS “ISO”

-SFERA CONTENUTA –CONTENTS BALL - BOULE CONTENUE

-NICHT RAUSRAGENDE KUGEL

- SERVIZIO CRIOGENICO – CRYOGENIC SERVICE - SERVICE CRYOGÉNIQUE

- TIEFTEMPERATUR SERVICE

ADLER COMPANY

VALVOLA A SFERA "3 VIE" PASSAGGIO TOTALE 90° BALL VALVES "3 WAY" FULL BORE 90°

ROBINETS A BOISSEAU SPHERIQUE "3 VOIES" PASSAGE INTEGRAL 90° KUGELHÄHNE "3 WEGE" VOLLER DURCHGANG 90°

▪ ESECUZIONI ▪ EXECUTIONS ▪ EXECUTIONS ▪ AUSFÜHRUNGEN

VA

LV

OL

E I

N A

CC

IAIO

IN

OX

ST

AIN

LE

SS

ST

EE

L B

AL

L V

AL

VE

S

∅ ¼

”-⅜

”-¾

”- 1

¼”-

2”

∅ ½

”-1”

-1½

”

TYPE

FZ6 PN 25 ÷ 63

ISO 9001:2008 by L.R. PED DIR. 97/23/EC by L.R. ATEX DIR. 94/9/EC by B.V.

FIRE SAFE EXECUTION by L.R. ISO 15848 by TÜV

ANTISTATIC DEVICE by L.R. FIRE SAFE TESTED ISO 10497 by L.R.

CARATTERISTICHE DEL FILETTO THREAD FEATURES FILETAGES CARACTÉRISTIQUES GEWINDE KENNDATEN

IN ACCORDANCE TO ISO 7-1 – 1994

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Des

igna

tion

of

thre

ad s

ize

Num

ber

of th

read

s in

25.

4 m

m

Pit

ch

Hei

ght o

f th

read

Diameters of gauges plane

Gauges length (external threads)

Tolerance on position of

gauge plan on internal thread

Length of useful external thread not

less than

Fitting

allowance

Dia

met

er to

lera

nce

on

para

llel

inte

rnal

thre

ads

Maj

or

Pit

ch

Min

or

Nom

inal

Tolerance ±t1/2

Max

.

Min

.

For

nom

inal

g

auge

leng

th

For

max

imum

ga

uge

leng

th

For

min

imum

ga

uge

leng

th

Tolerance ±t1/2

2)

Tur

ns o

f th

read

2)

Tur

ns o

f th

read

2)

Tur

ns o

f th

read

P h d d2 d1

¼ 19 1,337 0,856 13,15 12,30 11,44 6 1,3 1 7,3 4,7 1,7 1 ¼ 9,7 11 8,4 3,7 2 ¾ ±0,104 3/8 19 1,337 0,856 16,66 15,80 14,95 6,4 1,3 1 7,7 5,1 1,7 1 ¼ 10,1 11,4 8,8 3,7 2 ¾ ±0,104 ½ 14 1,814 1,162 20,95 19,79 18,63 8,2 1,8 1 10 6,4 2,3 1 ¼ 13,2 15 11,4 5 2 ¾ ±0,142 ¾ 14 1,814 1,162 26,44 25,27 24,11 9,5 1,8 1 11,3 7,7 2,3 1 ¼ 14,5 16,3 12,7 5 2 ¾ ±0,142 1 11 2,309 1,479 33,24 31,77 30,29 10,4 2,3 1 12,7 8,1 2,9 1 ¼ 16,8 19,1 14,5 6,4 2 ¾ ±0,180

1 ¼ 11 2,309 1,479 41,91 40,43 38,95 12,7 2,3 1 15 10,4 2,9 1 ¼ 19,1 21,4 16,8 6,4 2 ¾ ±0,180 1 ½ 11 2,309 1,479 47,80 46,32 44,84 12,7 2,3 1 15 10,4 2,9 1 ¼ 19,1 21,4 16,8 6,4 2 ¾ ±0,180

2 11 2,309 1,479 59,61 58,13 56,65 15,9 2,3 1 18,2 13,6 2,9 1 ¼ 23,4 25,7 21,1 7,5 3 ¼ ±0,180

IN ACCORDANCE TO ANSI B1.20.1 – 1983

1 2 3 4 5 6 7 8 9 10 11

Nominal

Pipe Size

O.D. of

Pipe (D) T

hrea

ds/i

nch

(n)

Pitch of threads

(P)

Pitch diam. at beginning of external thread (E0)

Handtight engagement Effective thread, external

Length2 (L1) Diam.3

(E1) Length4 (L2) Diam.5

(E2) inch threads inch threads

¼ 0,540 18 0,05556 0,47739 0,2278 4,1 0,49163 0,4018 723 0,50250 3/8 0,675 18 0,05556 0,61201 0,240 4,32 0,32701 0,4078 734 0,63750 ½ 0,840 14 0,07143 0,75843 0,320 4,48 0,77843 0,5337 747 0,79179 ¾ 1,050 14 0,07143 0,96768 0,339 4,75 0,98887 0,5457 764 1,00179 1 1,315 11,5 0,0896 1,21363 0,400 4,6 1,23863 0,6828 785 1,25630

1 ¼ 1,660 11,5 0,0896 1,55713 0,420 4,83 1,58338 0,7068 813 1,60130 1 ½ 1,900 11,5 0,0896 1,79609 0,420 4,83 1,82237 0,7235 832 1,84130

2 2,375 11,5 0,0896 2,26902 0,436 5,01 2,29627 0,7565 870 2,31630 ADLER SpA –BALL VALVES 20010 S. STEFANO TICINO (MI) ITALY V.le BORLETTI, 14 Tel. +39/02974842.11 FAX +39/0297271698 E-mail: adler@adlerspa.com http://www.adlerspa.com