119
PDQ Replacement Parts Guide

PDQ Replacement Parts Guide

Embed Size (px)

Citation preview

Page 1: PDQ Replacement Parts Guide

PDQ Replacement Parts Guide

Page 2: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1036 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00507SS Key Plate A00696SS Collar, Pitman

A00234 Washer, Flat A07031066 Bearing, Pitman

A01036WDU04A Toggle Seat A0103600115 Flinger

A00509SS Wedge, Moveable Jaw A0103600116 Seal, Pitman Bearing

A00524C Spring, Tension A00683SS Cap, Pitman

A00517C Collar, Tension Spring A00695SS Flinger, Side Bearing, Outside

A0163600110 Toggle Seat, Moveable A00687SR Cap, Side Bearing, RH

A00825ST Tension Rod A00687SL Cap, Side Bearing, LH

A00611A Toggle Seat A0103600115 Flinger

A0103600116 Seal, Pitman Bearing

VARIABLE PARTS A00685SS Seal, Inner Side Bearing

PART NO. DESCRIPTION A00686SR Seal, Inner Side Bearing, RH

*A00602LH Jaw, Stationary A00686SL Seal, Inner Side Bearing, LH

*A00603SS Jaw, Moveable A00694SS Flinger, Side Bearing, Inner

A00613 Toggle Plate A07032071 Bearing, Side

A07035006 Sleeve, Tapered Bearing

*Parts available but not stocked A00682SW Lockwasher

A00682SN Locknut

A07033028 Lockwasher

A07030028 Locknut

A00689SS Seal, Outer Side Bearing

A00691 Plate, End, Shaft

A07030016 Locknut, Shaft End

A00692 Cap, Shaft End

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available - please inquire Rev Date: 1-25-2012

Page 3: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1236 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431283 Key Plate A00696SS Collar, Pitman

A0152400319 Bolt, Key Plate A07031066 Bearing, Pitman

A00234 Washer, Flat A0103600115 Flinger

A0103600110 Toggle Seat A0103600116 Seal, Pitman Bearing

A00509SS Wedge, Moveable Jaw A00683SS Cap, Pitman

A00524C Spring, Tension A00695SS Flinger, Side Bearing, Outside

A00517C Collar, Tension Spring A00687SR Cap, Side Bearing, RH

A0163600110 Toggle Seat, Moveable A00687SL Cap, Side Bearing, LH

A0124200202 Tension Rod A0103600115 Flinger

A00611A Toggle Seat A0103600116 Seal, Pitman Bearing

A00685SS Seal, Inner Side Bearing

A00686SR Seal, Inner Side Bearing, RH

VARIABLE PARTS A00686SL Seal, Inner Side Bearing, LH

PART NO. DESCRIPTION A00694SS Flinger, Side Bearing, Inner

*A123606601 Jaw, Stationary A07032071 Bearing, Side

*A123606604 Jaw, Moveable A07035006 Sleeve, Tapered Bearing

A00613S Toggle Plate A00682SW Lockwasher

A00682SN Locknut

*Parts available but not stocked A07033028 Lockwasher

A07030028 Locknut

A00689SS Seal, Outer Side Bearing

A00691 Plate, End, Shaft

A07030016 Locknut, Shaft End

A00692 Cap, Shaft End

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available - please inquire Rev Date: 5-14-2012

Page 4: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1242 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431150 Key Plate A0442805701 Shaft

A00234 Washer A07031093 Bearing, Pitman

A0123600418 Wedge, Pull A0087603 Flinger, Pitman

A0264000117 Bolt, Swing A00865 Cap, Pitman End

A00524C Spring A0086601 Seal, Pitman

A00517C Collar, Tension Spring A0153600125 Seal, Inner Side Bearing

A00883 Seal, Inner Side Bearing, RH

A00884 Seal, Inner Side Bearing, LH

A00889 Flinger, Side Bearing

A07032077 Bearing, Side

A07035007 Sleeve, Side Bearing

A07033030 Lockwasher, Tapered Sleeve

A07030030 Locknut, Tapered Sleeve

A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

A00890 Flinger, Side Bearing

A0443113301 Cap, Side Bearing, RH

A0443113302 Cap, Side Bearing, LH

A0443113401 Seal, Outer, Side Bearing

A07028503 Dowel Pin

A02540G01 Setscrew

A00875A Spacer, Collar, Bearing

A0153600114 Dowel Pin

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 5: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1248 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431150 Key Plate A0442807301 Shaft

A0152400319 Bolt, Square Head A07031093 Bearing, Pitman

A00234 Washer A0087603 Flinger, Pitman

A0123600418 Wedge, Pull A00865 Cap, Pitman End

A0264000117 Bolt, Swing A0086601 Seal, Pitman

A00524C Spring A0153600125 Seal, Inner Side Bearing

A00517C Collar, Tension Spring A00883 Seal, Inner Side Bearing, RH

A04431181 Toggle Seat, Pitman A00884 Seal, Inner Side Bearing, LH

A00889 Flinger, Side Bearing

A07032077 Bearing, Side

A07035007 Sleeve, Side Bearing

A07033030 Lockwasher, Tapered Sleeve

A07030030 Locknut, Tapered Sleeve

A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

A00890 Flinger, Side Bearing

A0443113301 Cap, Side Bearing, RH

A0443113302 Cap, Side Bearing, LH

A0443113401 Seal, Outer, Side Bearing

A07028503 Dowel Pin

A02540G01 Setscrew

A00875A Spacer, Collar, Bearing

A0153600114 Dowel Pin

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 6: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1636 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0442806102 Shaft

A04431144 Key Plate A07031093 Bearing, Pitman

A0152400319 Bolt, Square Head A0087603 Flinger, Pitman

A00509B Wedge, Moveable Jaw A00865 Cap, Pitman End

A0153600109 Toggle Seat A0086601 Seal, Pitman

A0123600416 Spacer, Seat A0153600125 Seal, Inner Side Bearing

A0163600110 Toggle Seat A00883 Seal, Inner Side Bearing, RH

A0123600418 Wedge, Pull A00884 Seal, Inner Side Bearing, LH

A00524C Spring A00889 Flinger, Side Bearing

A00517C Collar, Tension Spring A07032077 Bearing, Side

A0152400311 Tension Rod A07035007 Sleeve, Side Bearing

A0153600107 Shim, 3/8" A07033030 Lockwasher, Tapered Sleeve

A0153600108 Shim, 1/4" A07030030 Locknut, Tapered Sleeve

A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

A00890 Flinger, Side Bearing

A0443113301 Cap, Side Bearing, RH

A0443113302 Cap, Side Bearing, LH

VARIABLE PARTS A0443113401 Seal, Outer, Side Bearing

PART NO. DESCRIPTION A07028503 Dowel Pin

A0153605022 Toggle Plate A02540G01 Setscrew

*A0163605027 Jaw, Stationary A00875A Spacer, Collar, Bearing

*A0163605028 Jaw, Moveable A0153600114 Dowel Pin

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 7: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1648 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431144 Key Plate A0442806001 Shaft

A00234 Washer A07031077 Bearing, Pitman

A0164800103 Toggle Seat, Adjustable A07032072 Bearing, Side

A04431181 Toggle Seat A02540A22 Sleeve, Tapered Bearing

A00524C Spring A03242A28 Pin, Screw

A00517C Collar, Tension Spring A0086601 Seal, Pitman

A0442805101 Tension Rod A0153600125 Seal, Inner Side Bearing

A0164810003 Toggle Plate A00883 Seal, Inner Side Bearing, RH

A00884 Seal, Inner Side Bearing, LH

A00889 Flinger, Side Bearing

A07033032 Lockwasher, Side Bearing

A07030032 Locknut, Side Bearing

A07033030 Lockwasher, Tapered Sleeve

A07030030 Locknut, Tapered Sleeve

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-21-2015

Page 8: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1836 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0442804401 Shaft

A00524C Spring A07031093 Bearing, Pitman

A00517C Collar, Tension Spring A0087603 Flinger, Pitman

A00509B Wedge, Moveable Jaw A00865 Cap, Pitman End

A0442805101 Tension Rod A0086601 Seal, Pitman

A0153600109 Toggle Seat A0153600125 Seal, Inner Side Bearing

A0153600107 Shim, 3/8" A00883 Seal, Inner Side Bearing, RH

A0153600108 Shim, 1/4" A00884 Seal, Inner Side Bearing, LH

A00889 Flinger, Side Bearing

A07032077 Bearing, Side

A07035007 Sleeve, Side Bearing

A07033030 Lockwasher, Tapered Sleeve

A07030030 Locknut, Tapered Sleeve

A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

A00890 Flinger, Side Bearing

A0443113301 Cap, Side Bearing, RH

A0443113302 Cap, Side Bearing, LH

VARIABLE PARTS A0443113401 Seal, Outer, Side Bearing

PART NO. DESCRIPTION A07028503 Dowel Pin

A0153605022 Toggle Plate A02540G01 Setscrew

*A0163605027 Jaw, Stationary A00875A Spacer, Collar, Bearing

*A0163605028 Jaw, Moveable A0153600114 Dowel Pin

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 9: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2036 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A00881E Shaft

A00894 Wedge, Moveable Jaw A07031061 Bearing, Pitman

A00809A Key Plate, Upper A00875A Collar, Pitman Bearing

A00807A Key Plate, Lower A0086503 Cap, Pitman

A00811A Toggle Seat A0086601 Seal, Pitman Bearing

A00524C Spring A0153600125 Seal, Inner Side Bearing

A00517C Collar, Tension Spring A00883 Seal, Inner Side Bearing, RH

A00885A Tension Rod A00884 Seal, Inner Side Bearing, LH

A00889 Flinger, Side Bearing

A07032077 Bearing, Side

A07035007 Sleeve, Tapered Bearing

A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

A00890 Flinger, Side Bearing

VARIABLE PARTS A00869 Cap Side Bearing, RH

PART NO. DESCRIPTION A00874 Cap, Side Bearing, LH

A00812X Toggle Plate A00870 Seal, Side Bearing

*A00802D Jaw, Stationary A07033016 Lockwasher, Shaft

*A00803D Jaw, Moveable A07030016 Locknut, Shaft

A0069201 Cap, Shaft End

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-21-2015

Page 10: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2236 CEDARAPIDS® JAW CRUSHER - Grease

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer, Flat A0442804401 Shaft

A00809A Key Plate, Upper A07031093 Bearing, Pitman

A00807A Key Plate, Lower A0087603 Flinger, Pitman

A00894 Wedge, Moveable Jaw A00865 Cap, Pitman

A0153600109 Toggle Seat A0086601 Seal, Pitman Bearing

A0123600416 Spacer, Seat A0153600125 Seal, Inner, Side Bearing

A0163600110 Toggle Seat, Moveable A00883 Seal, Inner, Side Bearing, RH

A0123600418 Wedge, Pull A00884 Seal, Inner Side Bearing, LH

A00524C Spring, Tension A00889 Flinger, Inside Side Bearing

A00517C Collar, Tension Spring A07032077 Bearing, Side

A4589020002 Locknut, Spherical A07035007 Sleeve, Taper Bearing

A0152400110 Tension Rod A07033030 Lockwasher, Sleeve

A0153600105 Shim, 1" A07030030 Locknut, Sleeve

A0153600106 Shim, 1/2" A07033028 Lockwasher, Side Bearing

A0153600107 Shim, 3/8" A07030028 Locknut, Side Bearing

A0153600108 Shim, 1/4" A00890 Flinger, Side Bearing

A0183600155 Cover A0443113301 Cap, Side Bearing, RH

A0264000117 Bolt A0443113302 Cap, Side Bearing, LH

A00870 Seal, Outer Side Bearing

A02540G01 Setscrew, Special

A00875A Collar, Bearing Spacer

VARIABLE PARTS A0153600114 Dowel Pin

PART NO. DESCRIPTION

*A0223600610 Jaw, Stationary

*A0223600613 Jaw, Moveable

A04431548 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 11: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2236 CEDARAPIDS® JAW CRUSHER - Grease / Oil

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer, Flat A0442804401 Shaft

A00809A Key Plate, Upper A07031093 Bearing, Pitman

A00807A Key Plate, Lower A00875A Collar, Bearing Spacer

A00894 Wedge, Moveable Jaw A0223600152 Collar, Bearing Spacer

A0153600109 Toggle Seat A0124800140 Cap, Pitman

A0123600416 Spacer, Seat A0223600153 Cap, Pitman

A0163600110 Toggle Seat, Moveable A0443158301 Seal, End

A0123600418 Wedge, Pull A0443158401 Seal, Side Bearing

A00524C Spring, Tension A0124800127 Seal, Inner, Side Bearing, LH

A00517C Collar, Tension Spring A0223600155 Seal, Inner, Side Bearing, LH

A4589020002 Locknut, Spherical A0124800128 Seal, Inner Side Bearing, RH

A0152400110 Tension Rod A0223600154 Seal, Inner Side Bearing, RH

A0153600105 Shim, 1" A0302535905 Screw, Greasing

A0153600106 Shim, 1/2" A07032077 Bearing, Side

A0153600107 Shim, 3/8" A07035007 Sleeve, Side Bearing

A0153600108 Shim, 1/4" A07033030 Lockwasher, Sleeve

A0183600155 Cover A07030030 Locknut, Sleeve

A0264000117 Bolt A07033028 Lockwasher, Side Bearing

A07030028 Locknut, Side Bearing

VARIABLE PARTS A0443113303 Cap, Side Bearing, LH

PART NO. DESCRIPTION A0443113306 Cap, Side Bearing, LH

*A0223600610 Jaw, Stationary A0443113304 Cap, Side Bearing, RH

*A0223600613 Jaw, Moveable A0443113305 Cap, Side Bearing, RH

A04431548 Toggle Plate A0443164301 Seal, Outer Side Bearing

A02540G01 Setscrew, Special

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 2-11-2016

Page 12: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2248 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0442805601 Shaft

A04431198 Wedge, Moveable Jaw A03240A17 Collar, Pitman Bearing

A0443119301 Key Plate, Upper A07031089 Bearing, Pitman

A0443119401 Key Plate, Lower A0304000203 Flinger, Pitman

A04431181 Toggle Seat A03240A08A Cap, Pitman

A00925 Spring, Tension A03240A16 Flinger, Side Bearing, Outside

A00926 Collar, Tension Spring A3240A12R Cap, Side Bearing, RH

A0224800124 Rod, Tension A03240A12L Cap, Side Bearing, LH

A00928 Pin, Tension Rod A0304000204 Seal, Pitman Bearing

A00929 Yoke, Tension Rod A03240A10D Seal, Inner Side Bearing

A0164800103 Toggle Seat, Adjustable A03240A11R Seal, Inner Side Bearing, RH

A03240A11L Seal, Inner Side Bearing, LH

A03240A15B Flinger, Side Bearing, Inside

A07032074 Bearing, Side

VARIABLE PARTS A03242A25 Sleeve, Tapered Bearing

PART NO. DESCRIPTION A03242A29 Lockwasher

A0224810003 Toggle Plate A07030033 Locknut

A03240A1301 Seal, Outer Side Bearing

A02540G01 Setscrew

A07033040 Lockwasher

A07030034 Locknut

A03242A28 Pin

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 12-31-2015

Page 13: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2436 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0243600201 Shaft

A0243600109 Key Plate, Upper A03240A17 Collar, Pitman Bearing

A0243600110 Key Plate, Lower A07031089 Bearing, Pitman

A00811A Toggle Seat A0304000203 Flinger, Pitman

A00925 Spring A03240A08A Cap, Pitman

A00926 Collar, Tension Spring A03240A16 Flinger, Side Bearing, Outside

A00927 Tension Rod A3240A12R Cap, Side Bearing, RH

A00928 Pin, Tension Rod A03240A12L Cap, Side Bearing, LH

A00929 Yoke, Tension Rod A0304000204 Seal, Pitman Bearing

A0243600111 Toggle Seat, Adjustable A03240A10D Seal, Inner Side Bearing

A03242A18 Shim, 1" A03240A11R Seal, Inner Side Bearing, RH

A03242A19 Shim, 3/4" A03240A11L Seal, Inner Side Bearing, LH

A03242A20 Shim, 1/2" A03240A15B Flinger, Side Bearing, Inside

A07032074 Bearing, Side

A03242A25 Sleeve, Tapered Bearing

A03242A29 Lockwasher

A07030033 Locknut

A03240A1301 Seal, Outer Side Bearing

VARIABLE PARTS A02540G01 Setscrew

PART NO. DESCRIPTION A07033040 Lockwasher

A0243640003 Toggle Plate A07030034 Locknut

*A0243640005 Jaw, Stationary A03242A28 Pin

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 14: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2442 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0094201 Shaft

A04431514 Key Plate, Upper, RH A00939 Collar, Pitman Bearing

A04431515 Key Plate, Upper, LH A07031016 Bearing, Pitman

A04431516 Key Plate, Lower, RH A07032057 Bearing, Side

A04431517 Key Plate, Lower, LH A02540A22 Sleeve, Tapered Bearing

A0244200108 Seat, Adjustable Toggle A07033032 Lockwasher

A09300226 Spacer, Toggle Seat A07030032 Locknut

A09300228 Wedge, Pull A07033030 Lockwasher

A03242A18 Shim, 1" A07030030 Locknut

A03242A19 Shim, 3/4" A0364800105 Setscrew, Inner Seal

A03242A20 Shim, 1/2"

A0264000117 Bolt, Swing

A00524C Spring

A09300071 Cap, Spring

A0264000118 Tension Rod

A00906 Wedge, Moveable Jaw

A09300005 Bolt, Wedge

A04431518 Seat, Toggle

VARIABLE PARTS

PART NO. DESCRIPTION

*A0254040004 Jaw, Moveable

*A0254040005 Jaw, Stationary

A0244200157 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 15: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2540 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0095001 Angle Support, Toggle Bearing, RH A00939 Collar, Pitman Bearing

A0095002 Angle Support, Toggle Bearing, LH A07031016 Bearing, Pitman

A0090401 Key Plate, Upper, RH A07032057 Bearing, Side

A0090402 Key Plate, Upper, LH A07034006 Sleeve, Tapered Bearing

A0090501 Key Plate, Lower, RH A07033030 Lockwasher

A0090502 Key Plate, Lower, LH A07030030 Locknut

A00234 Washer A02540G01 Setscrew, Special

A00910 Wedge, Toggle Bearing

A00925 Spring

A00927 Tension Rod

A00928 Yoke, Tension Rod

A00928 Pin, Tension Rod

A00906 Wedge, Moveable Jaw

A00930 Bolt

A00908 Seat, Toggle

A03242A30 Capscrew

A03242A31 Capscrew

VARIABLE PARTS

PART NO. DESCRIPTION

*A00902 Jaw, Moveable

*A00901K Jaw, Stationary

A00909 Toggle Plate, 26"

A00909L Toggle Plate 28-1/2"

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 16: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2742 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431530 Key Plate, Upper, RH A0304000207 Shaft

A04431532 Key Plate, Upper, LH A03240A17 Collar, Pitman Bearing

A04431531 Key Plate, Lower, RH A07031089 Bearing, Pitman

A04431533 Key Plate, Lower, LH A09300006 Seal, O-Ring

A00234 Washer A09300233 Seal, Pitman Bearing

A0244200108 Seat, Toggle Adjustable A0364800105 Setscrew, Inner, Seal

A09300226 Spacer, Toggle Seat A09300012 Seal, Inner Side Bearing

A09300228 Wedge, Pull A09300013 Seal, Inner Side Bearing, RH

A03242A18 Shim, 1" A09300014 Seal, Inner Side Bearing, LH

A03242A19 Shim, 3/4" A4524012525 O-Ring

A03242A20 Shim, 1/2" A07032074 Bearing, Side

A0264000117 Bolt, Swing A07030034 Locknut, Bearing Sleeve

A00524C Spring A07033040 Plate, Lock

A09300071 Cap, Spring A07033033 Lockwasher, Shaft

A0264000118 Tension Rod A07030033 Locknut, Shaft

A00906 Wedge, Moveable Jaw A4524012524 O-Ring

A09300005 Bolt, Wedge A09300015 Cap, Side Bearing, RH

A09300016 Cap, Side Bearing, LH

A09300018 Seal, Outer Side Bearing

VARIABLE PARTS

PART NO. DESCRIPTION

*A0264000127 Jaw, Moveable

*A0254040005 Jaw, Stationary

A0244200157 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 17: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3042 CEDARAPIDS® JAW CRUSHER - Grease

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0304200112 Shaft

A03240A17 Collar, Pitman Bearing

A07031089 Bearing, Pitman

A0304200113 Flinger, Pitman

A0443128601 Cap, Pitman

A03240A16 Flinger, side Bearing, Outside

A03240A12R Cap, Side Bearing, RH

A03240A12L Cap, Side Bearing, LH

A0304000204 Seal, Pitman

A03240A10D Seal, Inner Side Bearing

A03240A11R Seal, Inner Side Bearing, RH

A03240A11L Seal, Inner Side Bearing, LH

A03240A15B Flinger, Side Bearing, Inside

A07032074 Bearing, Side

A03242A25 Sleeve, Side Bearing

A07033033 Lockwasher

A07030033 Locknut

A03240A1301 Seal, Outer Side Bearing

A02540G01 Setscrew

VARIABLE PARTS A07033040 Lockwasher

PART NO. DESCRIPTION A07030040 Locknut

A03242A28 Pin, Screw

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 18: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3042 CEDARAPIDS® JAW CRUSHER - Grease / Oil

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431284 Key Plate, Upper A0442810001 Shaft

A04431285 Key, Plate, Lower A03240A17 Collar, Pitman Bearing

A00234 Washer A07031089 Bearing, Pitman

A09300548 Seat, Adjustable Toggle A09300006 Seal, O-Ring

A09300226 Spacer, Toggle Seat A0304200145 Cap, Pitman Bearing

A09300228 Wedge, Pull A09300233 Seal, Pitman Bearing

A03242A18 Shim, 1" A09300012 Seal, Inner Side Bearing

A03242A19 Shim, 3/4" A0304200146 Seal, Inner Side Bearing, RH

A03242A20 Shim, 1/2" A0304200147 Seal, Inner Side Bearing, LH

A0264000117 Bolt, Swing A4524012514 O-Ring

A00524C Spring A03242A25 Sleeve, Side Bearing

A0930007101 Cap, Spring, Double A07032074 Bearing, Side

A0304200110 Tension Rod A07030034 Locknut, Bearing Sleeve

A4559050060 Nut, Spherical A07033040 Plate, Lock

A04431288 Wedge, Moveable Jaw A07033033 Lockwasher, Shaft

A09300005 Bolt, Wedge A07030033 Locknut, Shaft

A04431462 Seat, Toggle A0443137601 Cap, Side Bearing, RH

A0443137602 Cap, Side Bearing, LH

A09300018 Seal, Outer Side Bearing

VARIABLE PARTS

PART NO. DESCRIPTION

*A0304205103 Jaw, Moveable

*A0304205104 Jaw, Stationary

A04431463 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware ia available-please inquire Rev Date: 1-25-2012

Page 19: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3054 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431736 Key Plate, Upper, RH A0442811401 Shaft

A04431737 Key, Plate, Upper, LH A0305450032 Collar, Pitman Bearing

A04431738 Key Plate, Lower, RH A07031089 Bearing, Pitman

A04431739 Key Plate, Lower, LH A09300006 Seal, O-Ring

A00234 Washer A0304200145 Cap, Pitman Bearing

A0305450026 Seat, Adjustable Toggle A09300233 Seal, Pitman Bearing

A09300226 Spacer, Toggle Seat A09300012 Seal, Inner Side Bearing

A09300228 Wedge, Pull A0304200146 Seal, Inner Side Bearing, RH

A03242A18 Shim, 1" A0304200147 Seal, Inner Side Bearing, LH

A03242A19 Shim, 3/4" A4524012514 O-Ring

A03242A20 Shim, 1/2" A03242A25 Sleeve, Side Bearing

A0264000117 Bolt, Swing A07032074 Bearing, Side

A00524C Spring A07030034 Locknut, Bearing Sleeve

A0930007101 Cap, Spring, Double A07033040 Plate, Lock

A0304200110 Tension Rod A07033033 Lockwasher, Shaft

A4559050060 Nut, Spherical A07030033 Locknut, Shaft

A0305450009 Wedge, Moveable Jaw A0443137601 Cap, Side Bearing, RH

A00930 Bolt, Wedge A0443137602 Cap, Side Bearing, LH

A0305450010 Seat, Toggle A09300018 Seal, Outer Side Bearing

A0305450034 Plate, Wear, Pitman Barrel

VARIABLE PARTS

PART NO. DESCRIPTION

*A0305450018 Jaw, Moveable

*A0305450053 Jaw, Stationary

A0305450019 Toggle Plate

A0305450005 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-21-2015

Page 20: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3240 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00906 Wedge, Moveable Jaw A03240A17 Collar, Pitman Bearing

A00930 Bolt, Wedge A07031089 Bearing, Pitman

A00907 Bolt, Key Plate A03240A14 Flinger, Pitman

A00234 Washer A03240A08A Cap, Pitman

A00908 Seat, Toggle A03240A10D Seal, Inner Side Bearing

A00927 Tension Rod A03240A11R Seal, Inner Side Bearing, RH

A00929 Yoke, Tension Rod A03240A11L Seal, Inner Side Bearing, LH

A00928 Pin, Tension Rod A03240A15B Flinger, Side Bearing, Inside

A00925 Spring A07032074 Bearing, Side

A00926 Collar, Tension Spring A07034043 Sleeve, Tapered Bearing

A03242A30 Capscrew A07033033 Lockwasher. Side Bearing

A03242A31 Capscrew A07030033 Locknut, Side Bearing

A03240A16 Flinger, Side Bearing, Outside

VARIABLE PARTS A03240A12R Cap, Side Bearing, RH

PART NO. DESCRIPTION A03240A12L Cap, Side Bearing, LH

A00909L Toggle Plate A03240A1301 Seal, Side Bearing, Outer

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 21: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3242 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431398 Key Plate, Upper, RH A03242A0701 Shaft

A04431400 Key Plate, Upper, LH A03240A17 Collar

A04431399 Key Plate, Lower, RH A07031089 Bearing, Pitman

A04431401 Key Plate, Lower, LH A09300006 O-Ring

A00234 Washer A09300233 Seal, Pitman Bearing

A09300548 Seat, Adjustable Toggle A0364800105 Setscrew, Inner Seal

A09300226 Spacer, Toggle Seat A09300012 Seal, Inner Side Bearing

A09300228 Wedge, Pull A09300013 Seal, Inner Side Bearing, RH

A03242A18 Shim, 1" A09300014 Seal, Inner Side Bearing, LH

A03242A19 Shim, 3/4" A4524012525 O-Ring

A03242A20 Shim, 1/2" A03242A25 Sleeve, Side Bearing

A0264000117 Bolt, Swing A07032074 Bearing, Side

A00524C Spring A07030034 Locknut, Tapered Bearing

A09300071 Cap, Spring A07033040 Plate, Lock

A0304200110 Tension Rod A07033033 Lockwasher, Shaft

A03242L04 Wedge, Moveable Jaw A07030033 Locknut, Shaft

A03242L05 Bolt, Wedge A4524012524 O-Ring

A04431462 Seat, Toggle A09300015 Cap, Side Bearing, RH

A03242A13 Seat, Toggle A09300016 Cap, Side Bearing, LH

A09300018 Seal, Outer Side Bearing

VARIABLE PARTS

PART NO. DESCRIPTION

A04431463 Toggle Plate, 30"

*A0324205004 Jaw, Stationary

*A0324205007 Jaw, Moveable

A03242L06 Toggle Plate, 28-1/2"

A03242L09 Toggle Plate, 30-1/2"

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 01-04-2016

Page 22: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3646 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A00234 Washer A0442807101 Shaft

A0364500113 Shim, 1" A07031015 Bearing, Pitman

A0364500114 Shim, 3/4" A4524012513 O-Ring

A0364500115 Shim, 1/2" A0443131201 Seal, Pitman Bearing

A0264000117 Bolt, Swing A0443131401 Seal, Inner Side Bearing

A00925 Spring A4524012514 O-Ring

A00926 Collar, Spring A0364500132 Sleeve, Side Bearing

A0364500122 Tension Rod A07032054 Bearing, Side

A0443130801 Wedge, Moveable Jaw A07030037 Nut, Lock, Sleeve

A0364500127 Bolt, Wedge A07033043 Plate Lock

A0443130901 Seat, Toggle A07030035 Locknut, Shaft

A07033041 Plate Lock

A4524012516 O-Ring

VARIABLE PARTS A0443131603 Cap, Side Bearing, RH

PART NO. DESCRIPTION A0443131604 Cap, Side Bearing, LH

A04431463 Toggle Plate A0443131701 Seal, Outer Side Bearing

*A0364504920 Jaw, Stationary A4524012515 O-Ring

*A0364504930 Jaw, Moveable

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 23: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3648 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431344 Key Plate, Upper, RH A0442811601 Shaft

A04431345 Key Plate, Upper, LH A0443170801 Collar, Pitman Bearing

A04431346 Key Plate, Lower, RH A07031015 Pitman Bearing

A04431347 Key Plate, Lower, LH A4524012513 O-Ring Seal

A00234 Washer, Flat A0364800140 Cap, Pitman End

A0364800118 Adjustable Toggle Seat A0443131201 Seal, Pitman Bearing

A09300066 Spacer, Toggle Seat A0443131401 Seal, Inner Side Bearing

A09300068 Wedge, Pull A0364800142 Seal, Inner Side Bearing, RH

A0364500110 Seat, Shim A0364800143 Seal, Inner Side Bearing, LH

A0364500113 Shim, 1" A4524012514 O-ring Seal

A0364500114 Shim, 3/4" A0364500132 Sleeve, Side Bearing

A0364500115 Shim, 1/2" A07032054 Side Bearing

A0264000117 Bolt, Swing A07030037 Locknut, Sleeve

A00925 Spring, Tension A07033043 Lock Plate

A0930066601 Cap, Spring A07033041 Lockwasher, Shaft

A0364500122 Rod, Tension A07030035 Locknut, Shaft

A0443130801 Wedge, Moveable Jaw A0443131605 Cap, Side Bearing, RH

A0364500127 Bolt, Wedge A0443131606 Cap, Side Bearing, LH

A0443130901 Toggle Seat A0443131701 Seal, Outer Side Bearing

VARIABLE PARTS FLYWHEEL ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431318 Toggle Plate A0364504904 Plate, Shaft End

*A0364504921 Jaw, Moveable

*A0364504922 Jaw, Stationary

A0364800113 Pitman Wear Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 24: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3660 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431682 Key Plate, Upper A0442811501 Shaft

A04431683 Key Plate, Lower A0443132701 Collar, Pitman Bearing

A00234 Washer A07031014 Pitman Bearing

A0424800216 Seat, Shim A4524012519 O-Ring Seal

A0424800143 Spacer, Toggle Seat A0443132801 Cap, Pitman End

A09300228 Wedge, Pull A0443132901 Seal, Pitman Bearing

A0424800209 Shim, 1" A0443133101 Seal, Inner Side Bearing

A0424800208 Shim, 3/4" A0443133201 Seal, Inner Side Bearing, RH

A0424800207 Shim, 1/2" A0443133202 Seal, Inner Side Bearing, LH

A0264000117 Bolt, Swing A4524012518 O-ring Seal

A00925 Spring A0424800219 Sleeve, Side Bearing

A0930066601 Cap, Spring A07032055 Side Bearing

A0364500122 Tension Rod A07030048 Locknut, Sleeve

A00928 Pin, Yoke A07033046 Lock Plate

A4559050060 Locknut, Spherical A07033047 Lockwasher, Shaft

A0443159201 Wedge, Moveable Jaw A07030045 Locknut, Shaft

A0546000136 Seat, Toggle A0443133301 Cap, Side Bearing, RH

A0443133302 Cap, Side Bearing, LH

A0443133401 Seal, Outer Side Bearing

VARIABLE PARTS

PART NO. DESCRIPTION

*A0366004901 Jaw, Moveable

*A0366004902 Jaw, Stationary

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 25: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4248 CEDARAPIDS® JAW CRUSHER

S/N 439XX

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431380 Key Plate, Upper, RH A0442807401 Shaft

A04431381 Key Plate, Upper, LH A0443132701 Collar, Pitman Bearing

A04431630 Key Plate, Lower, RH A07031014 Pitman Bearing

A04431631 Key Plate, Lower, LH A4524012519 O-Ring Seal

A0424800216 Seat, Shim A0443132801 Cap, Pitman End

A0424800145 Seat, Adjustable Toggle A0443132901 Seal, Pitman Bearing

A0424800143 Spacer, Toggle Seat A0443133101 Seal, Inner Side Bearing

A09300228 Wedge, Pull A0443133201 Seal, Inner Side Bearing, RH

A0424800209 Shim, 1" A0443133202 Seal, Inner Side Bearing, LH

A0424800208 Shim, 3/4" A4524012518 O-ring Seal

A0424800207 Shim, 1/2" A0424800219 Sleeve, Side Bearing

A0264000117 Bolt, Swing A07032055 Side Bearing

A00925 Spring A07030048 Locknut, Sleeve

A0930066601 Cap, Spring A07033046 Lock Plate

A0424800217 Tension Rod A07033047 Lockwasher, Shaft

A00928 Pin, Yoke A07030045 Locknut, Shaft

A4559050060 Locknut, Spherical A0443133301 Cap, Side Bearing, RH

A04248B03A Wedge, Moveable Jaw A0443133302 Cap, Side Bearing, LH

A04248B04 Bolt, Wedge A0443133401 Seal, Outer Side Bearing

A0424800140 Seat, Toggle Insert A0424800139 Plate, Pitman Barrel Wear

VARIABLE PARTS

PART NO. DESCRIPTION

*A0424804902 Jaw, Moveable

*A0424804903 Jaw, Stationary

A0424800147 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 26: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4248 CEDARAPIDS® JAW CRUSHER

S/N 488XX

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431380 Key Plate, Upper, RH A0442807402 Shaft

A04431381 Key Plate, Upper, LH A0424800181 Collar, Pitman Bearing

A04431630 Key Plate, Lower, RH A07031014 Pitman Bearing

A04431631 Key Plate, Lower, LH A4524012519 O-Ring Seal

A0424800216 Seat, Shim A0424800182 Cap, Pitman End

A0424800145 Seat, Adjustable Toggle A0424800158 Seal, Pitman Bearing

A0424800143 Spacer, Toggle Seat A0443133101 Seal, Inner Side Bearing

A09300228 Wedge, Pull A0424800183 Seal, Inner Side Bearing, RH

A0424800209 Shim, 1" A0424800184 Seal, Inner Side Bearing, LH

A0424800208 Shim, 3/4" A4524012526 O-ring Seal

A0424800207 Shim, 1/2" A0424800219 Sleeve, Side Bearing

A0264000117 Bolt, Swing A07032055 Side Bearing

A00925 Spring A07030048 Locknut, Sleeve

A0930066601 Cap, Spring A07033046 Lock Plate

A0424800217 Tension Rod A07033047 Lockwasher, Shaft

A00928 Pin, Yoke A07030045 Locknut, Shaft

A4559050060 Locknut, Spherical A0443133304 Cap, Side Bearing, RH

A04248B03A Wedge, Moveable Jaw A0443133303 Cap, Side Bearing, LH

A04248B04 Bolt, Wedge A0443133401 Seal, Outer Side Bearing

A0424800140 Seat, Toggle Insert A0424800139 Plate, Pitman Barrel Wear

A0424800215 End Plate

VARIABLE PARTS

PART NO. DESCRIPTION

*A0424804902 Jaw, Moveable

*A0424804903 Jaw, Stationary

A0424800147 Toggle Plate

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 27: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5460 CEDARAPIDS® JAW CRUSHER

FINAL ASSEMBLY SHAFT, PITMAN & BEARING

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431650 Key Plate, Upper, RH A0442811801 Shaft

A04431651 Key Plate, Upper, LH A0546000258 Collar, Pitman Bearing

A04431652 Key Plate, Lower RH A07031094 Bearing, Pitman

A04431653 Key Plate, Lower, LH A0546000259 Cap, Pitman End

A00234 Washer A0546000129 Seal, Pitman Bearing

A0264000117 Bolt, Swing A0546000130 Seal, Inner Side Bearing

A0546000164 Collar, Spring A0546000260 Seal, Inner Side Bearing, LH

A4559050060 Nut, Spherical A0546000261 Seal, Inner Side Bearing, RH

A0443159201 Wedge, Jaw A0546000133 Sleeve, Side Bearing

A0546000136 Seat, Toggle A07032078 Side Bearing

A0546000150 Locknut, Tapered Sleeve

A07033047 Lockwasher, Bearing

VARIABLE PARTS A0546000155 Locknut, Bearing

PART NO. DESCRIPTION A07033048 Lockwasher, Bearing

*A0546000192 Jaw, Moveable A0443159403 Cap, Side Bearing, RH

*A0546000185 Jaw, Stationary A0443159404 Cap, Side Bearing, LH

*Parts available but not stocked

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 28: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4336 CEDARAPIDS® SIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08004W02 Bearing Clamp A04408002 Bearing Housing

A08004N37 Bolt, Side Plate A04407005 Cover, Inner

A08004W07 Breaker Plate, Lower A04407034 Flinger, Inner

A08004W08 Plate, Feed End A08003D56A Gasket

A08004W28 Breaker Plate, Upper A07032038 Bearing

A08004W30 Breaker Plate, Top A07033025 Lockwasher

A08004W31(D) Feed Plate A07030025 Locknut

A4103504814 Breaker Bar A07221019 Stabilizing Ring

A04405032 Sleeve A04407167 Cover, Outer

A08004WA05 End Plate A04407089 Flinger, Outer

A08101W02 Bolt

A07119022 Nut, 3" Slotted MISCELLANEOUS

PART NO. DESCRIPTION

BREAKER LINERS A0810101003 Extension, Top, Far End

PART NO. DESCRIPTION A0810101004 Extension, Top, Near Side

A08004W05 Liner, Bottom, RH A0810101005 Extension, Bottom, Far Side

A08004W06 Liner, Bottom, LH A0810101006 Extension, Bottom, Near Side

A08004W11 Liner, Lower Feed End RH A0810101506 Extension, RH Openings

A08004W12 Liner, Lower Feed End, LH A0810101507 Extension, LH Opening

A08004W13 Liner, Segmental, RH A0810101510 Liner

A08004W14 Liner, Segmental, LH A0810101511 End Plate

A08004W15 Liner, Upper Feed End, RH A0810102065 Plate, Lower Feed

A08004W16 Liner, Upper Feed End, LH A0800415009 Locknut, Shaft End

A08004W17 Liner, Upper Discharge, RH A0800415018 Liner, Feed End

A08004W18 Liner, Upper Discharge, LH A0800415019 Liner, Feed End

A08004W19 Liner, Upper Guide, RH A0800415021 Liner

A08004W20 Liner, Upper Guide, LH A0800415022 Breaker Plate, Discharge End

A08004W21 Liner, Lower Guide, RH A0800415023 Extension, End

A08004W22 Liner, Lower Guide, LH A0800415036 Liner

A08004W26 Liner, Inspection Door A0800415072 Sleeve, HD

A08004W27 Liner, Door, Segmental A0800422515 Liner, Top Side, RH

A08101N10 Tie Bolt

IMPELLER & SHAFT ASSEMBLY

SAFETY RELEASE ASSEMBLY PART NO. DESCRIPTION

PART NO. DESCRIPTION A08101C01 Impeller Bar

A08004N54 Spacer, 1" A08005B07 Spherical Nut

A08004N55 Spacer 2" A08005B08 Wedge

A08004N52 Guide, Outside Bar A08101C02 Bolt, Impeller Wedge

A411040020003 Adapter, Shear Block A07399011 Bolt, 2" X 10"

A08004W23 Cover, Bar

A08004N30 Shear Block

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 29: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4338 CEDARAPIDS® SIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08004W07 Breaker Plate, Lower A04408001 Bearing Housing

A4103504988 Bar, Breaker A08004N08 Flinger, Inner

A4405032 Sleeve, Single Bar A04407072 Cover, Inner

A08004Y16 Cover, Bar A07221024 Stabilizing Ring

A08004W28 Breaker Plate, Lower, Disch. End A07032071 Spherical Bearing

A08004Y19 Breaker Plate, Center, Disch. End A07033028 Lockwasher

A08004Y20 Breaker Plate, Top, Disch. End A07030028 Locknut

A08101N10 Tie Bolt, Breaker Plate A04407071 Cover, Outer

A08004N09 Flinger, Outer

BREAKER LINERS A08004WM02 Clamp, Bearing

PART NO. DESCRIPTION

A08004Y04 Liner, Bottom MISCELLANEOUS

A08004Y08 Liner, Lower Feed End PART NO. DESCRIPTION

A08004W13 Liner, Seg. RH Feed & Disch. Ends A0810101510 Liner, Extension

A08004W14 Liner, Seg. LH Feed & Disch. Ends A0810101511 End Plate

A08004W27 Liner, Door, Segmental A08004N10 Tie Bolt

A08004Y09 Liner, Upper, RH Feed End

A08004Y10 Liner, Upper, LH Feed End IMPELLER & SHAFT ASSEMBLY

A08004Y11 Liner, Upper, RH Disch. End PART NO. DESCRIPTION

A08004Y12 Liner, Upper LH Disch. End A08101C01 Impeller Bar

A08004Y13 Liner, Lower, RH Guide A08005B07 Spherical Nut

A08004Y14 Liner, Lower, LH Guide A08005B08 Wedge

A08004W26 Liner, Inspection Door A08101C02 Bolt, Impeller Wedge

A07399011 Bolt, 2" X 10"

SAFETY RELEASE ASSEMBLY

PART NO. DESCRIPTION

A08004N54 Spacer, 1"

A08004N55 Spacer 2"

A08004N52 Guide, Outside Bar

A411040020003 Adapter, Shear Block

A08004W23 Cover, Bar

A08004N30 Shear Block

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 30: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4340 CEDARAPIDS® SIIB CRUSHER

BREAKER LINERS SAFETY RELEASE ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08004Y04 Liner, Bottom A08004N54 Spacer, 1"

A08004Y08 Liner, Lower Feed End A08004N55 Spacer, 2"

A08004W13 Liner, Segmental Feed End, RH A08004N52 Guide, Single Bar

A08004W14 Liner, Segmental Feed End, LH A411040020003 Adapter, Shear Block

A08004W13 Liner, Segmental Disch End, RH A08004N30 Shear Block

A08004W14 Liner, Segmental Disch End, LH

A08004W27 Liner, Door Segmental ASSEMBLY

A08004Y09 Liner, Upper Feed End, RH PART NO. DESCRIPTION

A08004Y10 Liner, Upper Feed End, LH A08004Y05 Plate, Feed End

A08004Y11 Liner, Upper Discharge End, RH A08004W07 Plate, Breaker, Bottom

A08004Y12 Liner, Upper Discharge End, LH A08004W28 Plate, Breaker, Lower Disc. End

A08004Y13 Liner, Lower Guide, RH A08004Y19 Plate, Breaker, Center Disc. End

A08004Y14 Liner, Lower Guide, LH A08004Y20 Plate, Breaker, Top Disc. End

A08004W26 Liner, Inspection Door A08101N10 Tie Bolt

A08101Z03 Liner, Top, RH A08003N63 Stud

A08101Z04 Liner, Top, LH A08003W11 Bolt, Side Plate

A04405032 Sleeve

SHAFT ASSEMBLY A08004Y16 Cover, Bar

PART NO. DESCRIPTION A4103504914 Breaker Bar

A04408001 Bearing Housing A4101004512 Rod, Chain Curtain

A08004N08 Flinger, Inner

A04407072 Cover, Inner IMPELLER ASSEMBLY

A07221024 Stabilizing Ring PART NO. DESCRIPTION

A07032071 Spherical Bearing A08101C01 Impeller Bar

A07033028 Lockwasher A08005B07 Spherical Nut

A07030028 Locknut A07399011 Bolt, Impeller Bar

A04407071 Cover, Outer A08005B08 Wedge, Impeller Bar

A08004N09 Flinger, Outer A08101C02 Bolt, Impeller Wedge

A08004WM02 Clamp, Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 31: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5348 CEDARAPIDS® SIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08005W07 Breaker Plate A08005B13 Bearing Housing

A08005W08 Plate, Lower Feed A08005B14 Cover, Inner

A08005W32 Breaker Plate A08005B15 Flinger, Inner

A08005W33 Breaker Plate, Top A08003D56A Gasket

A08005B27 Tie Bolt A07032057 Bearing

A4104006188 Bar, Adjustable Breaker A07033032 Lockwasher

A41040063 Bar, Breaker A07030032 Locknut

A08005B24 Sleeve, Bar A07221028 Stabilizing Ring

A08004N37 Bolt, Side Plate A08005B16 Cover, Outer

A08003N63 Stud, Breaker Plate A08005B17 Flinger, Outer

A08005B24B Sleeve, Dual Bar A08005W02 Bearing Clamp

BREAKER LINERS HYDRAULIC FEED PLATE

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08005W05 Liner, Bottom, RH A0810210030 Pivot, Feed Plate

A08005W12 Liner, Center Section Lower, RH A0810210031 Liner, Feed Plate

A08005W13 Liner, Center Section Lower, LH A0810210036 Lock, Feed Plate

A08005W16 Liner, Center Section Upper, RH A0810210037 Pin, Pivot

A08005W17 Liner, Center Section Upper, LH

A08005W18 Liner, Center Section Upper, RH IMPELLER & SHAFT ASSEMBLY

A08005W19 Liner, Center Section Upper, LH PART NO. DESCRIPTION

A08005W26 Liner, Door A08005B06 Impeller Bar

A08005W30 Liner, Top Side, RH A08005B07 Spherical Nut

A08005W31 Liner, Top Side, LH A08005B08 Wedge

A08005W14 Liner, Center Section Lower, RH A08005B10 Bolt, Impeller Wedge

A08005W15 Liner, Center Section Lower, LH A07399011 Bolt, 2" X 10"

A08005W20 Liner, Segmental

A08005W21 Liner, Segmental SAFETY RELEASE ASSEMBLY

A08005W27 Liner, Door, Segmental PART NO. DESCRIPTION

A08005B52 Spacer, Narrow

A08005B53 Spacer, Wide

A08005B51 Guide, Single Bar

A08005W11 Adapter, Shear Block

A08005W23 Cover, Bar

A08005W09-08 Shear, Block

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 32: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

6360 CEDARAPIDS® SIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08005Y15 Breaker Plate, Bottom A08005Y06 Flinger, Inner

A08005Y21 Liner, Segmental Feed End, RH A08005Y07 Cover, Inner

A08005Y22 Liner, Segmental Feed End, LH A07032075 Bearing

A08005Y27 Liner, Upper Guide, LH A08005Y08 Cover, Outer

A08005Y29 Liner, Upper Discharge End, LH A08005Y09 Flinger, Outer

A08005Y34 Sleeve, Bar, Adjustable A07030047 Locknut

A0800560005 Liner, Upper Inspection Door, LH

A0800560006 Liner, Upper Inspection Door, RH SAFETY RELEASE ASSEMBLY

A0800560007 Dual Sleeve, Gemini Bar PART NO. DESCRIPTION

A08005Y40 Liner, Segmental Door A02827D07 Adapter, Shear Block

A08005Y10 Clamp, Bearing

BREAKER LINERS IMPELLER & SHAFT ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08005W05 Liner, Bottom, RH A08102Y02 Impeller Bar

A08005W12 Liner, Center Section Lower, RH A08005B08 Wedge

A08005W13 Liner, Center Section Lower, LH A08102Y03 Bolt, Impeller Wedge

A08005W16 Liner, Center Section Upper, RH A0810220009 Bolt, 2" X 12-1/2" Sq Head

A08005W17 Liner, Center Section Upper, LH

A08005W18 Liner, Center Section Upper, RH

A08005W19 Liner, Center Section Upper, LH

A08005W26 Liner, Door

A08005W30 Liner, Top Side, RH

A08005W31 Liner, Top Side, LH

A08005W14 Liner, Center Section Lower, RH

A08005W15 Liner, Center Section Lower, LH

A08005W20 Liner, Segmental

A08005W21 Liner, Segmental

A08005W27 Liner, Door, Segmental

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-21-2015

Page 33: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3042 CEDARAPIDS® DIIB CRUSHER

LINERS

PART NO. DESCRIPTION

A04406049 Liner Beside Insp. Door, Right

A04406065 Liner Beside Insp. Door, Left

A04406020 Liner Below Insp. Door

A04406025 Inspection Door Liner, Lower

A04405021 Outside Liner, Right

A04405043 Outside Liner, Left

SAFETY RELEASE ASSEMBLY

PART NO. DESCRIPTION

A04406033 Guide, Single Bar

A04405020 Spacer, Narrow

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-13-2016

Page 34: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3645H CEDARAPIDS® DIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08003S28 Breaker Plate, Center A04408002 Bearing Housing

A08003Y22 Sleeve, Bar A04407005 Cover, Inner

A08003D39 Sleeve, Bar A04407034 Flinger, Inner

A08003N63 Stud A08003D56A Gasket

A07032038 Bearing

SAFETY RELEASE ASSEMBLY A07033025 Lockwasher

PART NO. DESCRIPTION A07030025 Locknut

A08003Y21 Guide, Single Bar A07221019 Stabilizing Ring

A411040020003 Adapter, Shear Block A04407167 Cover, Outer

A04407089 Flinger, Outer

IMPELLER & SHAFT ASSEMBLY

PART NO. DESCRIPTION

A08100Y02 Impeller Bar

A04405076 Nut

A08005B08 Wedge

A08100Y03 Bolt, Impeller Wedge

A07146128 Bolt, Impeller Bar

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 35: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3645 CEDARAPIDS® DIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08003D39 Sleeve, Bar A08003D56 Gasket

A08003N63 Stud A08003D52 Flinger, Inner

A08003D53 Cover, Inner

A08003D54 Cover, Outer

SAFETY RELEASE ASSEMBLY A08003D55 Flinger, Outer

PART NO. DESCRIPTION A07221013 Stabilizing Ring

A411040020003 Adapter, Shear Block A07032037 Bearing

A07033021 Lockwasher, Bearing

IMPELLER & SHAFT ASSEMBLY A07030021 Locknut, Bearing

PART NO. DESCRIPTION

A08100C04 Impeller Bar

A08100C02 Bolt, Impeller Wedge

A08003N04 Key

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 36: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4350 CEDARAPIDS® DIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A4103504914 Bar, Vertical Adjustable Breaker A04408001 Bearing Housing

A04405032 Sleeve, Breaker Bar A08004N08 Flinger, Inner

A08004N37 Bolt, Side Plate A04407072 Cover, Inner

A08101N10 Tie Bolt A04407071 Cover, Outer

A08004N09 Flinger, Outer

IMPACT BREAKER LINERS A07032009 Bearing

PART NO. DESCRIPTION A07033028 Lockwasher, Bearing

A08004N42 Liner, Center Segmental, RH A07030028 Locknut, Bearing

A08004N43 Liner, Center Segmental, LH A07221024 Stabilizing Ring

A08004N44 Liner, End Segmental, RH

A08004N45 Liner, End Segmental, LH

A08004N49 Liner, Center Sect Top Center, LH

A08004N57 Liner, Vertical Adj Bar Cover

SAFETY RELEASE ASSEMBLY

PART NO. DESCRIPTION

A411040020003 Adapter, Shear Block

A08004N30 Shere Block

A08004N52 Guide, Vertical Adjustable Bar

A08004N54 Spacer, Narrow

A08004N55 Spacer, Wide

IMPELLER & SHAFT ASSEMBLY

PART NO. DESCRIPTION

A08004N05 Key

A08101C01 Impeller Bar

A08005B08 Wedge

A08101C02 Bolt, Wedge

A08005B07 Nut, 2" Spherical

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 37: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5360 CEDARAPIDS® DIIB CRUSHER

FINAL ASSEMBLY IMPELLER BEARING ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08005B27 Tie Bolt A08005B13 Bearing Housing

A08005B24 Sleeve, Bar A08005B14 Cover, Inner

A08005B15 Flinger, Inner

A08003D56A Gasket

IMPELLER & SHAFT ASSEMBLY A07032057 Bearing

PART NO. DESCRIPTION A07033032 Lockwasher

A08005B06 Impeller Bar A07030032 Locknut

A08005B07 Spherical Nut A07221028 Stabilizing Ring

A08005B08 Wedge A08005B16 Cover, Outer

A08005B10 Bolt, Impeller Wedge A08005B17 Flinger, Outer

A07399011 Bolt, 2" X 10" A08005W02 Bearing Clamp

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-14-2012

Page 38: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1516 CEDARAPIDS® ANDREAS HSI CRUSHER

PILLOW BLOCK BEARING ASSEMBLY FRAME LINERS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A07033033 Lockwasher A0861061010 Liner, Side, Feed, Discharge, Door

A07030033 Locknut A0861061011 Liner, Side

A07221027 Stabilizing Ring A0861061012 Liner, Side & Top

A0861061019 Liner, Rotor

PRIMARY BREAKER PLATE MTG A0861061020 Liner, Rotor

PART NO. DESCRIPTION A0861061021 Liner, Feedplate

A0865060018 Keeper, Apron Pivot Tube A0861061022 Liner, Feedplate

A0865060029 Guide, Breaker Plate Connection Rod A0861061023 Liner, Discharge

A0865060009 Stop Rod, Primary Breaker A0861061024 Liner, Discharge

A0865060032 Bumper, Breaker Plate Connection A0861061025 Liner, Feedplate

A0865060055 Capnut, Lock, Primary Bridge A0861061026 Liner, Discharge

A0865060058 Pin, Capnut Lock

A0865060051 Stopnut, Breaker Plate IMPELLER & SHAFT

A0865060046 Pin, Hair PART NO. DESCRIPTION

A0860020319 Bar, Rotor

SECONDARY BREAKER PLATE MTG A0865060014 Wedge, Primary

PART NO. DESCRIPTION A04431806 Impeller Bar, Manganese

A0865060018 Keeper, Apron Pivot Tube A0443180601 Impeller Bar, Manganese w/ Chrome

A0865060029 Guide, Breaker Plate Connection Rod

A0865060032 Bumper, Breaker Plate Connection

A0865060057 Pin, Capnut Lock

A0865060048 Capnut, Lock, Secondary Bridge

A0865060051 Stopnut, Breaker Plate

A0865060046 Pin, Hair

SECONDARY BREAKER PLATE LINERS

PART NO. DESCRIPTION

A0443169904 Liner, Breaker Plate

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 09-24-2015

Page 39: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5048 CEDARAPIDS® HSI CRUSHER

PILLOW BLOCK BEARING ASSEMBLY FRAME LINERS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A07032019 Bearing A0861061010 Liner, Side

A07033028 Lockwasher A0861061011 Liner, Side

A07030028 Locknut A0861061012 Liner, Side

A0861061013 Liner, Lower Feed Plate

A0861061014 Liner, Side

BREAKER PLATES A0861061015 Liner, Side, 1/2" Thick

PART NO. DESCRIPTION A0861061016 Liner, Side, 1" Thick

A04431774 Breaker Plate, Casting A0861061010 Liner, Feed End

A0861061011 Liner, Feed End

SECONDARY BREAKER PLATE LINERS A0861061010 Liner, Back

PART NO. DESCRIPTION A0861061011 Liner, Back

A0443169902 Liner, Breaker Plate A0861061010 Liner, Door

ADJUSTABLE PARTS-BREAKER PLATES FEEDPLATE & LINERS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0860020350 Flat, End Cap A0861061017 Liner, Feed plate - Side

A0860020336 Bumper, Breaker Rod A0861061010 Liner, Feed plate

IMPELLER WEDGES & SHIMS IMPELLER BARS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0860020290 Wedge, Impeller Bar A0443170401 Impeller Bar, 4" Wide x 48" CR25

A0860020011 Wedge, Lower A0443170404 Impeller Bar, 5" Wide x 48" CR25

A0860020269 Bracket, Lower Wedge A0443170409 Impeller Bar, 5" Wide x 48" Tool Steel

A0860020347 Master Shim

A0860020292 Shim, 1/4"

A0860020293 Shim, 1/8"

A0860020294 Shim, 1/16"

A0860020295 Shim, 1/32"

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 5-24-2012

Page 40: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5064 CEDARAPIDS® HSI CRUSHER

PILLOW BLOCK BEARING ASSEMBLY FRAME LINERS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A07032022 Bearing A04431700 Liner, Side

A07033032 Lockwasher A04431701 Liner, Tri

A07030032 Locknut A0443170120 Liner, Tri

A4524012502 O-Ring A0443170121 Liner

A4524012503 O-Ring A0443170201 Liner, Shaft, LH

A4524012511 O-Ring A0443170202 Liner, Shaft, RH

A4524012558 O-Ring A0443170001 Liner, Door, Beveled

A0443170122 Liner

A04431700 Liner, Back

BREAKER PLATES A04431700 Liner, Front

PART NO. DESCRIPTION

A0860020024 Tension Rod

A0860020025 Pin, Tension Rod FEED CHUTE with LINERS

A0860020026 Block, Nylon PART NO. DESCRIPTION

A0860020027 Plate, with Washer A04431700 Liner, Bottom

A0860020028 Locknut, with Cover A04431701 Liner, Side, LH

A04559050060 Nut, Adjusting A0443170120 Liner, Side, RH

A0443169902 Liner, Breaker Plate

ADJUSTABLE PARTS-BREAKER PLATES

IMPELLER & SHAFT PART NO. DESCRIPTION

PART NO. DESCRIPTION A0860020350 Flat, End Cap

A0443170301 Shaft, Impeller A0860020336 Bumper, Breaker Rod

A04431704 Impeller Bar, 4" x 32", CR25 A0860020367 Washer, Spherical w/ Nut

A0443170405 Impeller Bar, 5" x 32", CR25 A0860020368 Stop Rod, Primary

A0443170410 Impeller Bar, 5" x 32", Tool Steel A0860020369 Stop Rod, Secondary

A0860020060 Wedge, 4" Bar

A0860020011 Wedge, Lower

A0860020055 Bracket, Lower Wedge

A0860020029 Plate, Bar Retainer

A0860020049 Ring, Wear Protection

A0860020061 Master Shim

A0860020062 Shim, 1/4"

A0860020063 Shim, 1/8"

A0860020064 Shim, 1/16"

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 9-13-2016

Page 41: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5064 CEDARAPIDS® HSI PHASE II CRUSHER

PILLOW BLOCK BEARING ASSEMBLY FRAME LINERS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A07032019 Bearing A0861061010 Liner, Side

A07033028 Lockwasher A0861061011 Liner, Side

A07030028 Locknut A0861061012 Liner, Side

A0861061013 Liner, Lower Feed Plate

A0861061014 Liner, Side

SECONDARY BREAKER PL LINERS A0861061015 Liner, Side, 1/2" thick

PART NO. DESCRIPTION A0861061016 Liner, Side, 1" thick

A0443169902 LINER, Breaker Plate

FEEDPLATE & LINERS

IMPELLER & SHAFT PART NO. DESCRIPTION

PART NO. DESCRIPTION A0861061018 Liner, Feedplate, Side

A04431704 Impeller Bar, 4" x 32", CR25 A0861061011 Liner, Feedplate

A0443170405 Impeller Bar, 5" x 32", CR25

A0443170410 Impeller Bar, 5" x 32", Tool Steel

A0860020346 Wedge, Impeller Bar ADJUSTABLE PARTS-BREAKER PLATES

A0860020011 Wedge, Lower PART NO. DESCRIPTION

A0860020269 Bracket, Lower Wedge A0860020349 Shaft, Breaker Plate

A0860020347 Shim, Master A0860020350 Flat, End Cap

A0860020292 Shim, 1/4" A0860020336 Bumper, Breaker Rod

A0860020293 Shim, 1/8"

A0860020294 Shim, 1/16"

A0860020295 Shim, 1/32"

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 5-24-2012

Page 42: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

2033 CEDARAPIDS® HAMMERMILL

HAMMERMILL - ASSEMBLY BEARING, SHAFT & DISC

PART NO. DESCRIPTION PART NO. DESCRIPTION

A02899BB06B Bolt, Eye A07032016 Bearing

A04431386 Liner, Upper Body, 1st Sect. RH A07035016 Sleeve, Tapered Bearing

A04431387 Liner, Upper Body, 1st Sect. LH A07033024 Lockwasher

A04431114 Liner, Upper Body, 2nd Sect, RH A07030024 Locknut

A04431126 Liner, Upper Body, 2nd Sect, LH

A06040A1501 Liner, Lower Body, RH

A06040A15 Liner, Lower Body, LH HAMMER ARMS & TIPS

A06040A13 Liner, Cleanout Door PART NO. DESCRIPTION

A06040A1601 Liner, Cover, RH A04431147 Tip, Hammer

A06040A16 Liner, Cover, LH

A06030A51 Bolt, Liner

A04431384 Liner, upper Body, 3rd Sect, RH

A04431385 Liner, upper Body, 3rd Sect, LH

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 1-25-2012

Page 43: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

3033 CEDARAPIDS® HAMMERMILL

HAMMERMILL - ASSEMBLY BEARING, SHAFT & DISC

PART NO. DESCRIPTION PART NO. DESCRIPTION

A06040A16 Liner, Cover A06030A33 Outer Seal

A06040A15 Liner, Lower Body, LH A06030A37 Cap, Bearing

A06040A1501 Liner, Lower Body, RH A06030A35 Spacer Ring, Brg - RH Side Only

A06030A10 Breaker Plate A07032003 Bearing

A06030A51 Bolt, Liner A07035002 Sleeve, Tapered Bearing

A06030A20 Grate, 1/2" A07033025 Lockwasher

A06030A21 Grate, 3/4" A07030025 Locknut

A06030A22 Grate, 1" A06030A34 Spacer, Bearing

A06030A23 Grate, 1-1/2" A06030A32 Seal, Inner

A06030A24 Grate, 2"

A06030A25 Grate, 3"

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 44: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4033 CEDARAPIDS® HAMMERMILL

HAMMERMILL - ASSEMBLY BEARING, SHAFT, & DISC

PART NO. DESCRIPTION PART NO. DESCRIPTION

A06040A10 Breaker Plate A06040A33 Seal, Bearing Grease, Outer

A06040A41 Stud, Breaker Plate A06040A37 Cap, Bearing

A06040A12 Collar, Throat A06040A36 Bearing, Pillow Block

A06040A11 Bracket, Throat A07030027 Locknut

A06040A17 Grate, Cover A07033027 Lockwasher

A02899BB06B Eye Bolt A07032045 Bearing

A412080038801 Pin A07035018 Sleeve, Bearing

A04431386 Liner, Upper Body, 1st Sect, RH A06040A34 Spacer, Bearing

A04431387 Liner, Upper Body, 1st Sect, LH A06040A35 Spacer Ring, Bearing, Right Side

A04431114 Liner, Upper Body, 2nd Sect, RH A06040A32 Seal, Bearing Grease, Inner

A04431126 Liner, Upper Body, 2nd Sect, LH A06040A22 Grate, 1"

A06040A13 Liner, Cleanout Door A06040A23 Grate, 1-1/2"

A06040A1601 Liner, Cover, RH A06040A24 Grate, 2"

A06040A16 Liner, Cover, LH A06040A25 Grate, 3"

A06040A1501 Liner, Lower Body, RH A06040A74 Grate, 4"

A06040A15 Liner, Lower Body, LH

A06030A51 Bolt, Liner

A04431384 Liner, Upper Body 3rd Sect, RH HAMMER ARMS & TIPS

A04431385 Liner, Upper Body 3rd Sect, LH PART NO. DESCRIPTION

A04431147 Lime Tip, (Clark)

A04431480 Arm, Hammer, Long, Fasturn

A04431481 Tip, Hammer, Alloy

A04431500 Arm, Hammer, Short

A04431501 Tip, Hammer, Manganese, Fasturn

A0970089801 Wire, Locking

A06040A30A Pin, Hammer

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 45: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5040 CEDARAPIDS® HAMMERMILL

HAMMERMILL - ASSEMBLY HAMMER ARMS & TIP

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04431541 Liner, Upper Body, 1st Sect, RH A04431567 Arm, Hammer

A04431544 Liner, Upper Body 2nd Sect, RH A04431535 Tip, Hammer

A04431545 Liner, Upper Body 2nd Sect, LH A0970089801 Wire, Locking

A04431546 Liner, Upper Body 3rd Sect, RH A06050A3601 Pin, Hammer

A06030A51 Bolt, Liner

A06050A16 Collar, Throat BEARING, SHAFT, DISC

A06050A1801 Stud, Throat Bracket PART NO. DESCRIPTION

A06050A23 Liner, Cover End A06050A35A Seal, Outer

A02899BB06B Bolt, Eye A06050A34A Cap, Bearing Housing

A06050A12 Liner, Lower Body, LH A06050A33 Spacer, Bearing, RH Side Only

A06050C14 Grate, 3/4" A07032020 Bearing

A06050C01 Grate, 1" A07035020 Sleeve, Bearing

A06050C02 Grate, 1-1/2" A07033030 Lockwasher

A06050C03 Grate, 2" A07030030 Locknut

A06050C04 Grate, 3" A06050A32A Spacer, Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-21-2015

Page 46: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

35" X 20' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A0804801502 Bearing Cartridge, Gear End

A0804707029 Guide, Spring A0804801504 Retainer, Bearing

A0804708074 Liner, Side Rear, RH A0804801503 Bearing Cartridge, Drive End

A0804708075 Liner, Side Rear, LH A07031049 Bearing

A0804707036 Liner, Front A0310800115 Plate, End

A08048A0901 Retainer, Bearing Race, Outer

A08048A1101 Retainer, Bearing and Seal

A45201015 Oil Seal

A0804801505 Spacer

A031080017086 Gear Set

A09400287 O-Ring

A07210002 Key

A07052008 Breather

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 47: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

38" X 18' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A08048A06 Bearing Housing, Gear End

A08047A07 Spring, 6.13 A08048A0701 Bearing Housing, Drive End

A08047A10 Guide, Horizontal Spring A08048A08 Retainer, Bearing Race, Inner

A08047A12A Liner, Rear, RH A07031049 Bearing

A08047A13A Liner, Rear, LH A0310800115 Plate, End

A08048A0901 Retainer, Bearing Race, Outer

VIBRATING FEEDER DRIVE A08048A1101 Retainer, Bearing and Seal

PART NO. DESCRIPTION A45201015 Oil Seal

A04405007 Cushion, Rubber A08048A12 Spacer

A031080017086 Gear Set

A09400287 O-Ring

A07210002 Key

A07052008 Breather

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 48: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

42" X 15' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A08048A06 Bearing Housing, Gear End

A08047A07 Spring, 6.13 A08048A0701 Bearing Housing, Drive End

A08047A10 Guide, Spring, Horizontal A08048A08 Retainer, Bearing Race, Inner

A08047A11B Liner, Center A07031049 Bearing

A08047A12 Liner, Rear, RH A0310800115 Plate, End

A08047A13 Liner, Rear, LH A08048A0901 Retainer, Bearing Race, Outer

A08048A1101 Retainer, Bearing and Seal

VIBRATING FEEDER DRIVE A45201015 Oil Seal

PART NO. DESCRIPTION A08048A12 Spacer

A04405007 Cushion, Rubber A031080017086 Gear Set

A09400287 O-Ring

A07210002 Key

A07052008 Breather

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 49: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

42" X 17' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A0804801502 Bearing Cartridge, Gear End

A0804707029 Guide, Spring A0804801504 Retainer, Bearing

A0804708074 Liner, Side Rear, RH A0804801503 Bearing Cartridge, Drive End

A0804708075 Liner, Side Rear, LH A07031049 Bearing

A0804707030 Liner, Front A0310800115 Plate, End

A0804707073 Liner, Discharge A08048A0901 Retainer, Bearing Race, Outer

A0804707072 Liner, Pan A08048A1101 Retainer, Bearing and Seal

A45201015 Oil Seal

VIBRATING FEEDER DRIVE A0804801505 Spacer

PART NO. DESCRIPTION A031080017086 Gear Set

A04405007 Cushion, Rubber A09400287 O-Ring

A07210002 Key

A07052008 Breather

A4524012544 O-Ring

A0945004301 Gear Set

A04C2000101 Sheave

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 50: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

42" X 18' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A08048A06 Bearing Housing, Gear End

A08047A07 Spring, 6.13 A08048A0701 Bearing Housing, Drive End

A08047A10 Guide, Horizontal Spring A08048A08 Retainer, Bearing Race, Inner

A08047A11B Liner, Center A07031049 Bearing

A0310800115 Plate, End

A08048A0901 Retainer, Bearing Race, Outer

A08048A1101 Retainer, Bearing and Seal

A45201015 Oil Seal

A08048A12 Spacer

A031080017086 Gear Set

A09400287 O-Ring

A07210002 Key

A07052008 Breather

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 51: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

42" X 20' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A0804801502 Cartridge, Gear End

A0804707029 Guide, Spring A0804801504 Retainer

A0804708074 Liner, Side RH A0804801503 Cartridge, Drive End

A0804708075 Liner, Side LH A07031049 Bearing

A0804707036 Liner, Front A0310800115 End Plate

A0804707040 Liner, Bottom A08048A0901 End Cap

A08048A1101 Housing, Oil Seal

SINGLE DECK GRIZZLY SECTION A45201015 Oil Seal

PART NO. DESCRIPTION A0804801505 Spacer

A0130701283 Bar, Bolted In A031080017086 Gear Set

A0130700438 Bar, Bolted In A09400287 O-Ring

A07210002 Key

VIBRATING FEEDER DRIVE A07052008 Breather

PART NO. DESCRIPTION A4524012544 O-Ring

A04405007 Cushion, Rubber A0945004301 Gear Set

A08049A07 Clamp, Motor

A0446020301 Collar

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 52: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

52" X 12' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A08048A06 Housing, Bearing, Gear End

A08047A07 Spring, 6.13 A08048A07 Housing, Bearing, Drive End

A08047A10 Guide, Spring, Horizontal A08048A08 Retainer, Bearing Race, Inner

A08047A11B Liner, Center A07031049 Bearing

A08047A12A Liner, Rear, RH A08048A09 Retainer, Bearing Race, Outer

A08047A13A Liner, Rear, LH A08048A10 Cap, End

A08048A11 Retainer, Bearing and Seal

VIBRATING FEEDER DRIVE A08048A12 Spacer

PART NO. DESCRIPTION A031080017086 Gear Set

A04405007 Cushion, Rubber A07052008 Breather

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 53: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

52" X 20' CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047A06 Spring, 13.75 A0310815123 Plate, End

A0804708074 Liner, Side, Rear, RH A4524012511 O-Ring

A0804708075 Liner, Side, Rear, LH A07031095 Bearing

A0804708076 Liner, Front A0311000181 Cartridge, Bearing

A0804708093 Liner, Bottom A4524012505 O-Ring

A0804708077 Liner, Bottom A45201015 Oil Seal

A0443167002 Housing, Seal

VIBRATING FEEDER DRIVE A0311000186 Sleeve, Labyrinth

PART NO. DESCRIPTION A0310800117 Plate, End

A04405007 Cushion, Rubber A031080012603 Gear Set

A08049A07A Clamp, Motor

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 54: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

62" X 24'-6" CEDARAPIDS® VIBRATING GRIZZLY FEEDER

VIBRATING FEEDER BOX VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A08047U03 Spring, 17.00 A07031088 Bearing

A08048E04 Bearing Housing

GRIZZLY A4524012510 O-Ring

PART NO. DESCRIPTION A08048E05 Retainer, Bearing and Seal

A08047Z01 Grizzly Bar A45201018 Oil Seal

A08048E06 Retainer, Bearing

VIBRATING FEEDER DRIVE A08048E07 Retainer, Bearing

PART NO. DESCRIPTION A08048E08 Spacer

A04405007 Cushion, Rubber A08048E09 Plate, End

A08049A07 Clamp, Motor A031080019006 Gear Set

A08049A07D Slide, Motor A08048E12 Case, Gear

A07052008 Breather

A08048E13 O-Ring

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 55: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4102 CEDARAPIDS® HORIZONTAL SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04404035 Spring, 9.00 A04404008 Washer, Shaft

A03104ST28 Coil Spring Jack Seat, RH A4080400306 Key

A03104ST28A Coil Spring Jack Seat, LH A03104AP04 Flinger

A03104AP03 Cap, Main Box

A03104AP06 Seal, Inner Housing

A03104AP07 Oil Seal

A03100A12A Plate, Hub Lock

A03104AP08 Spacer, Bearing

A03100B11 Gasket, Gear Case Cover

A03104AP10 Gasket, Gear Case Cover

A03104AP05 Cover, Bearing

A07031009 Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 56: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4122 CEDARAPIDS® HORIZONTAL SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A03104SC06 Wire Frame, Top Deck A04404008 Washer, Shaft

A03122A08 Discharge Chute - Top Deck A4080400306 Key

A04404036 Spring, 9.00 A03104AP04 Flinger

A04404045 Jack, Spring A03104AP03 Cap, Main Box

A04404014 Nut, Jack A03104AP06 Seal, Inner Housing

A09450950 Leaf Spring A03104AP07 Oil Seal

A04404005 Support, Spring Pads A031080015003 Gear Set

A03104ST28 Coil Spring Jack Seat, RH A03100A12A Plate, Hub Lock

A03104ST28A Coil Spring Jack Seat, LH A03104AP08 Spacer, Bearing

A03100B11 Gasket, Gear Case Cover

A03104AP10 Gasket, Gear Case Cover

A03104AP05 Cover, Bearing

A07031009 Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev date: 03-30-2016

Page 57: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4142 CEDARAPIDS® HORIZONTAL SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATING UNIT

PART NO. DESCRIPTION PART NO. DESCRIPTION

A03104SC06 Wire Frame, Top Deck A04404008 Washer, Shaft

A03122A08 Discharge Chute - Top Deck A4080400306 Key

A04404036 Spring, 9.00 A04404008 Washer, Shaft

A04404045 Jack, Spring A03104AP04 Flinger

A04404014 Nut, Jack A03104AP03 Cap, Main Box

A09450950 Leaf Spring A03104AP06 Seal, Inner Housing

A04404005 Pad A03104AP07 Oil Seal

A03104ST28 Coil Spring Jack Seat, RH A031080015003 Gear Set

A03104ST28A Coil Spring Jack Seat, LH A03100A12A Plate, Hub Lock

A03104AP08 Spacer, Bearing

A03100B11 Gasket, Gear Case Cover

A03104AP10 Gasket, Gear Case Cover

A03104AP05 Cover, Bearing

A07031009 Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 58: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

4' CEDARAPIDS® X-HVY DUTY HORIZONTAL SCREEN

SCREEN VIBRATING UNIT

PART NO. DESCRIPTION

A04404008 Washer, Shaft

A03108A04 Seal, Drive Shaft

A03108A05 Seal, Drive Shaft

A07031047 Bearing

A03108A07 Seal, Inner, Rotating

A03108A08 Seal, Inner, Fixed

A031080016003 Gear Set

A03108A09 Spacer, Fixed End Bearing

A03108A20 Gasket, Cover

A03108A19 Gasket, Inner

A03108A06 Cover, Bearing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 1-25-2012

Page 59: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5143 CEDARAPIDS® HORIZONTAL SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATING UNIT - Older

PART NO. DESCRIPTION PART NO. DESCRIPTION

A04405035 Spring, 9.00 A03108R23B Seal, Drive End - Rotating

A04404045 Jack A03108RF07 Seal, Drive End - Fixed

A04404014 Nut A07031073 Bearing

A03104ST28 Coil Spring Jack Seat, RH A03108RF24D Seal, Inner - Rotating

A03104ST28A Coil Spring Jack Seat, LH A03108RF08 Seal, Inner - Fixed

A09450950 Leaf Spring A031080017086 Gear Set

A04404005 Pad A03108RF09 Spacer, Bearing - Fixed End

A03108R17 Gasket, Inner

SCREEN VIBRATING UNIT - Newer

PART NO. DESCRIPTION

A4524012502 O-Ring

A03108R17 Gasket, Outer

A07031078 Bearing

A031080017086 Gear Set

A45201011 Oil Seal

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 60: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

5163 CEDARAPIDS® HORIZONTAL SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATING UNIT - Older

PART NO. DESCRIPTION PART NO. DESCRIPTION

A03144A19 Clamp, Wire - Top, Center, Bottom A031080012603 Gear Set

A03144A20 Clamp, Wire - Center Deck, LH A07031082 Bearing

A03144A23 Clamp, Wire - Bottom Deck, LH A09450705 Bearing Cartridge

A03144A25 Clamp, Wire, Bottom Deck, LH A4524012505 O-Ring

A04404035 Spring, 9.00 A09450706 Retainer, Bearing - Gear End

A04404014 Nut A0310815123 Plate, End - Gear Side

A04404045 Jack A09450707 Housing, Seal

A09450950 Leaf Spring A4524012511 O-Ring

A04404005 Pad A09450708 Spacer, Seal

A03104ST28 Coil Spring Jack Seat, RH A4520111 Oil Seal

A03104ST28A Coil Spring Jack Seat, LH A09450709 End Cap

A0310800117 Plate, End - Drive Side

A04C1300111 Sheave

A07409021 Bushing

A09450711 Gasket, Housing

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 61: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

6203 CEDARAPIDS® HORIZONTAL SCREEN

DISCHARGE LIP W/ LINERS

PART NO. DESCRIPTION

A03170DB Lip Discharge w/ Liner

A0317034012 Forming Lip Discharge

A0317034013 Liner Lip Discharge

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 10-05-2015

Page 62: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

6163 CEDARAPIDS® INCLINED SCREEN

SPRINGS & SNUBBER SCREEN VIBRATOR

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0945078304 Spring, 14.25 A07031095 Bearing

A0314402105 Snubber A4524012544 O-Ring

A04404035 Spring, Snubber, 9.00 A0330060076 Cartridge, Bearing

A03300761 Seat, Snubber Spring A0330060077 Housing, Seal, Inner

A45200261 Lip Seal

A4521000206 Sleeve, Wear, Inner

OIL LEVEL GAUGE & FILL A0330060079 Sleeve, Wear

PART NO. DESCRIPTION A0330060080 Housing, Seal, Inner

A07060003 Oil Gauge, 3/4" A45201015 Oil Seal

A07052008 Breather A4524012511 O-Ring

A0330070066 Spacer, Non-Drive End

A0330070067 End Plate, Shaft - Non-Drive End

A0330070068 Key

A07372059 Bushing, Eccentric

A0330070069 End Plate, Shaft - Drive End

A0330060081 Spacer, Free End

A0330060082 Spacer, Held End

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 63: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

6203 CEDARAPIDS® INCLINED SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATOR

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0330060005 Feedbox A0330060011 Shaft

A07031091 Bearing

SCREEN DECKS A0330080140 Retainer, Bearing, Inner

PART NO. DESCRIPTION A0330080141 Slinger, Oil

A0330070046 Clamp, Intake, RH A4524012533 O-Ring

A0330070047 Clamp, Intake, LH A0330070041 Cartridge, Bearing

A0330070072 Clamp, Middle A0330070037 Housing, Seal, Inner

A0330070044 Clamp, Discharge, RH A45200261 Lip Seal

A0330070045 Clamp, Discharge, LH A4521000206 Sleeve, Wear, Inner

A4524012539 O-Ring A0330074202 Sleeve, Wear

A0330060080 Housing, Seal, Inner

OIL LEVEL GAUGE & FILL A45203007 Oil Seal

PART NO. DESCRIPTION A4524012505 O-Ring

A07060003 Oil Gauge, 3/4" A0330072701 Spacer, Free End

A07052008 Breather A0330072801 Spacer, Held End

A0330070066 Spacer, Non-Drive End

SPRINGS & SNUBBER A0330070067 End Plate, Shaft - Non-Drive End

PART NO. DESCRIPTION A0330070068 Key

A0314402105 Snubber A07372059 Bushing, Eccentric

A04404035 Spring, Snubber, 9.00 A0330070069 End Plate, Shaft - Drive End

A03300761 Seat, Snubber Spring

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 64: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

7203 CEDARAPIDS® INCLINED SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATOR

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0330070024 Reinforcing Plate A07031091 Bearing

A4524012533 O-Ring

A0330070041 Cartridge, Bearing

SCREEN DECKS A0330070050 Housing, Seal, Inner

PART NO. DESCRIPTION A45200260 Lip Seal

A0330070046 Clamp, Intake, RH A4521000205 Sleeve, Wear, Inner

A0330070047 Clamp, Intake, LH A0330074202 Sleeve, Wear

A0330070072 Clamp, Middle A0330070037 Housing, Seal, Inner

A0330070044 Clamp, Discharge, RH A45201021 Oil Seal

A0330070045 Clamp, Discharge, LH A4524012505 O-Ring

A0330072701 Spacer, Free End

A0330072801 Spacer, Held End

OIL LEVEL GAUGE & FILL A0330070066 Spacer, Non-Drive End

PART NO. DESCRIPTION A0330070067 End Plate, Shaft - Non-Drive End

A07060003 Oil Gauge, 3/4" A0330070068 Key

A07372059 Bushing, Eccentric

A0330070069 End Plate, Shaft - Drive End

SPRINGS & SNUBBER

PART NO. DESCRIPTION

A0314402105 Snubber

A04404035 Spring, Snubber, 9.00

A03300761 Seat, Snubber Spring

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 65: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

8203 CEDARAPIDS® INCLINED SCREEN

SCREEN BOX ASSEMBLY SCREEN VIBRATOR

PART NO. PART NO. DESCRIPTION

A0330070046 Clamp, Intake, RH A4524012539 O-Ring

A0330070047 Clamp, Intake, LH A07031091 Bearing

A0330070072 Clamp, Middle A4524012533 O-Ring

A0330070044 Clamp, Discharge, RH A0330070041 Cartridge, Bearing

A0330070045 Clamp, Discharge, LH A0330070037 Housing, Seal, Inner

A0330074202 Sleeve, Wear

A45203007 Oil Seal

OIL LEVEL GAUGE & FILL A4524012505 O-Ring

PART NO. DESCRIPTION A0330072701 Spacer, Free End

A07060003 Oil Gauge, 3/4" A0330072801 Spacer, Held End

A07052008 Breather A0330070066 Spacer, Non-Drive End

A0330070067 End Plate, Shaft - Non-Drive End

A04C2000101 Sheave

SPRINGS & SNUBBER A0330070068 Key

PART NO. DESCRIPTION A07372059 Bushing, Eccentric

A0945078307 Spring, 11.50 A0330070069 End Plate, Shaft - Drive End

A0314402105 Snubber A0330080140 Retainer, Bearing, Inner

A04404035 Spring, Snubber, 9.00 A0330080141 Slinger, Oil

A03300761 Seat, Snubber Spring

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 03-30-2016

Page 66: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

280 MVP CEDARAPIDS® CRUSHER

LOWER ASSEMBLY LOCKING CYLINDER

PART NO. DESCRIPTION PART NO. DESCRIPTION

A024500430011 Seal Ring, Base Frame A0480030074 Locking Cylinder Assembly

A0450050032 Shim, .010 A024806330010 Locking Cylinder Piston

A0450050033 Shim, .015 A024806330020 Locking Cylinder Housing

A0450050055 Shim, .005 A004201000200 Seal

A024503620007 Cone Brake Plate A004202000000 Wear Ring

A024501660003 Thrust Plate A048000015501 Push Pin

A024501000001 Over Running Clutch A004200102220 Seal

A024501030010 Hub, Brake A0540030031 Cylinder Retainer Clip

A0420030021 Hub A4525950812 O-Ring

A024501000001 Clutch, Over Running

A0420030064 Cone Brake Shaft WEDGE PLATE ASSEMBLY

PART NO. DESCRIPTION

PINION SHAFT ASSEMBLY 450050042 Wedge Plate

PART NO. DESCRIPTION A024500080011 Lower Wedge Plate Seal Ring

A0420030020 Pinion Shaft A024500210001 Bearing, Lower Radial

A0450050019 Gear Set A024501560000 Bearing, Lower Thrust

A07138001 Bearing Cup, Inner A024501557000 Bearing, Upper Thrust

A07138007 Bearing Cone, Inner A024500070001 Upper Wedge Plate Seal Ring

A07112001 Bearing Cup, Outer A024504670013 Wear Band

A07112004 Bearing Cone, Outer

A024503070000 Key, Lock Ring CONE ASSEMBLY

A024504370001 Lock, Pinion Nut PART NO. DESCRIPTION

A0420030043 Locknut, Pinion A024500170510 Mantle Hold Down Bolt

A0420030019 Wear Ring, Seal A024500180001 Cone Seal Ring

A4524012586 O-Ring A024500130100 Bearing Retainer

A0420030014 Housing, Seal A024500190000 Cone Radial Bearing Retainer

A45200297 Oil Seal A02450223-0010 Torque Bar

A4524012585 O-Ring A004200024330 O-Ring

A004200024470 O-Ring A025404967000 Sponge Rubber Ring

A024500160520 Mantle Hold Down Washer

PINION HOUSING SHIMS A024500140522 Mantle Hold Down Nut

PART NO. DESCRIPTION A024500150000 Mantle Nut Cap

A024502070010 Shim, .010"

A024502070020 Shim, .020" FINAL ASSEMBLY

A024502070025 Shim, .025" A024805630000 Pin, Rotation Stop

A024502070050 Shim, .050" A024805640000 Block, Rotation Stop

A025402030001 Shim, .0747" A002012753250 Bushing, Rotation Stop

A025402070100 Shim, .100"

A025402940001 Shim, .1046"

A025402950000 Shim, .125"

A025402980000 Shim, .1875"

A025402990000 Shim, .250

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 12-10-2013

Page 67: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

280 MVP CEDARAPIDS® CRUSHER

RELIEF PISTON ASSEMBLY TRAMP IRON RELIEF SYSTEM

PART NO. DESCRIPTION PART NO. DESCRIPTION

A024800780000 Piston Assembly - Complete A024800580000 Relief Cylinder

A003320000525 Spiral Retaining Ring A024800620000 Dust Cap

A024800830000 Seal A024800550000 Piston Rod

A024800840000 Backup Seal A024800580110 Insert

A024800850000 Wear Ring A4525950866 O-Ring

A024800810000 Piston Core A003200013340 Crown Seal

A0540030096 Tension Rod

MANTLE'S AND BOWL LINERS A0540030098 Tension Rod Ear

A0420030022 Mantle, Coarse A024801480020 Split Coupler Base

A0420030023 Mantle, Fine A0540030097 Split Coupler Complete

A0420030024 Liner, Coarse A024805740000 Spherical Seat

A0420030025 Liner, Medium A024800640000 Guide Plate

A0420030026 Liner, Medium Fine A024800650000 Guide Rod Bushing

A0420030027 Liner, Fine A024500720000 Relief Valve, 3/8

A0420030028 Liner, Extra Fine A024800730040 Accumulator Adapter Block

A023604230000 Elbow, Adjusting Jack

UPPER ASSEMBLY

A024806800000 Bushing, Bowl Nut HEATER ASSEMBLY

A0480030074 Locking Cylinder Assembly A025404520020 Heater, Machined - 2000W

A048000015501 Push Pin A008740000000 Thermostat, On 60° Off 80°

A004200102220 Seal, Quad

A0540030031 Clip, Cylinder Retainer

A4589080090 Clevis, Short Jaw End

A024805930010 Pin, Clevis Assembly

A024805950000 Washer, 1-1/4, Clevis Bolt

A024805940000 Washer, Clevis Bolt

A024801260000 Nut, Clevis Bolt

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 12-10-2013

Page 68: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

380 MVP CEDARAPIDS® CRUSHER

LOWER ASSEMBLY LOCKING CYLINDER

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0480030011 Seal Ring, Base Frame A0480030074 Locking Cylinder Assembly

A024503620007 Cone Brake Plate A024806330010 Locking Cylinder Piston

A0480030019 Thrust Plate A024806330020 Locking Cylinder Housing

A0480030018 Cone Brake Shaft A004201000200 Seal

A025401000010 Over Running Clutch A004202000000 Wear Ring

A0480030054 Clutch Guide Ring A048000015501 Push Pin

A0480030075 Thrust Plate Shim, .005" A004200102220 Seal

A0480030076 Thrust Plate Shim, .010" A0540030031 Cylinder Retainer Clip

A0480030077 Thrust Plate Shim, .015" A4525950812 O-Ring

A4080200275 Key, Brake Shaft, Upper

A40802003 Key, Brake Shaft, Lower WEDGE PLATE ASSEMBLY

PART NO. DESCRIPTION

TRAMP IRON RELIEF SYSTEM A0480030087 Wedge Plate

PART NO. DESCRIPTION A0480030010 Lower Wedge Plate Seal Ring

A024800580000 Relief Cylinder A0480030012 Upper Wedge Plate Seal Ring

A024800620000 Dust Cap A0480030080 Lead Counterweight

A024800550000 Piston Rod A0480030079 Counterweight

A024800580110 Insert A0480030060 Counterweight

A4525950866 O-Ring A0480030039 Wear Plate

A003200013340 Crown Seal A0480030040 Wear Band

A0540030096 Tension Rod A0480030037 Shim, 1/4"

A0540030098 Tension Rod Ear A0480030038 Shim, 1/8"

A024801480020 Split Coupler Base 456581 Lower Thrust Bearing

A0540030097 Split Coupler Complete

A024805740000 Spherical Seat CONE ASSEMBLY

A024800640000 Guide Plate PART NO. DESCRIPTION

A024800650000 Guide Rod Bushing A0480030140 Mantle Hold Down Bolt

A024500720000 Relief Valve, 3/8 A0480030013 Cone Seal Ring

A024800730040 Accumulator Adapter Block A0480030141 Bearing Retainer

456582 Upper Radial Bearing

LUBRICATION ASSEMBLY A0480030030 Cone Radial Bearing Retainer

PART NO. DESCRIPTION A0480030149 Torque Bar

A4525200969 Valve Thermal Bypass A025403490004 Torque Bar Pin

A004200024330 O-Ring

A025404967000 Sponge Rubber Ring

A024500160520 Mantle Hold Down Washer

A024500140522 Mantle Hold Down Nut

A024500150000 Mantle Nut Cap

A07025186 Mantle Nut Cap Bolt

A0480030279 Bearing Retainer - 380X

A0480030348 Torque Bar - 380X

A0480030321 Mantle Hold Down Bolt - 380X

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 11-03-2016

Page 69: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

380 MVP CEDARAPIDS® CRUSHER

PINION SHAFT ASSEMBLY PINION HOUSING SHIMS

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0480030023 Shaft, Pinion A025402070010 Shim, .010"

A0480030022 Housing, Pinion A025402070020 Shim, .020"

A4513000244 Bearing Cup A025402070025 Shim, .025"

A4513000164 Bearing Cone, Inner A025402070050 Shim, .050"

A4513000161 Bearing Cone, Outer A025402030001 Shim, .0747"

A024803070000 Key, Lock Ring A025402070100 Shim, .100"

A024804370000 Pinion Nut Lock A025402940001 Shim, .1046"

A024800340000 Pinion Locknut A025402950000 Shim, .125"

A024805610000 Wear Ring Seal A025402980000 Shim, .1875"

A004200023440 O-Ring A025402990000 Shim, .250

A024805600000 Seal Housing

A45200291 Oil Seal RELIEF PISTON ASSEMBLY

A004200024740 O-Ring PART NO. DESCRIPTION

A004200024520 O-Ring A024800780000 Piston Assembly - Complete

A003320000525 Spiral Retaining Ring

MANGANESE ARRANGEMENTS A024800830000 Seal

PART NO. DESCRIPTION A024800840000 Backup Seal

A0480030024 Mantle, Coarse A024800850000 Wear Ring

A0480030051 Mantle, Fine A024800810000 Piston Core

A048003002401 Mantle, Medium

A0480030067 Liner, Coarse

A0480030073 Liner, Medium

A0480030069 Liner, Medium Fine

A0480030026 Liner, Fine

A0480030053 Liner, Extra Fine

MANGANESE RETENSION

PART NO. DESCRIPTION

A4589080090 Clevis

A024805930010 Pin, Clevis Mounting

A024805950000 Washer, Clevis Bolt

A024805940000 Washer, Clevis Bolt

A024801260000 Nut, Clevis Bolt

FINAL ASSEMBLY

PART NO. DESCRIPTION

A024805630000 Pin, Rotation Stop

A024805640000 Block, Rotation Stop

A002012753250 Bushing, Rotation Stop

A04431788 Guard, Strut

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 11-03-2016

Page 70: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

450 MVP CEDARAPIDS® CRUSHER

LOWER ASSEMBLY LOCKING CYLINDER

PART NO. DESCRIPTION PART NO. DESCRIPTION

A0540030103 Liner, Base Frame A0480030074 Locking Cylinder Assembly

A016050020000 Bronze UNS C464 0.25 x 0.25 A024806330010 Locking Cylinder Piston

A025400430002 Seal Ring, Base Frame A024806330020 Locking Cylinder Housing

A025403620007 Cone Brake Plate A004201000200 Seal

A025401660008 Thrust Plate A004202000000 Wear Ring

A025400990007 Cone Brake Shaft A048000015501 Push Pin

A025401000010 Over Running Clutch A004200102220 Seal

A0480030054 Clutch Guide Ring A0540030031 Cylinder Retainer Clip

A4525950812 O-Ring

TRAMP IRON RELIEF SYSTEM

PART NO. DESCRIPTION WEDGE PLATE ASSEMBLY

A024800580000 Relief Cylinder PART NO. DESCRIPTION

A024800620000 Dust Cap A0540030142 Wedge Plate

A024800550000 Piston Rod A025400080001 Lower Wedge Plate Seal Ring

A024800580110 Insert A025400770000 Lower Radial Bearing

A4525950866 O-Ring A025401560000 Lower Thrust Bearing

A003200013340 Crown Seal A0540030148 Retainer, Upper Radial Bearing

A0540030096 Tension Rod A025401558000 Upper Thrust Bearing

A0540030098 Tension Rod Ear A025400070003 Upper Wedge Plate Seal Ring

A024801480020 Split Coupler Base A025404670014 Wear Band

A0540030097 Split Coupler Complete A0540030136 Lead Counterweight

A024805740000 Spherical Seat A0540030137 Counterweight

A024800640000 Guide Plate A0480030060 Counterweight

A024800650000 Guide Rod Bushing A025402890140 Wear Plate

A024500720000 Relief Valve, 3/8 A025402890040 Shim, 1/4"

A024800730040 Accumulator Adapter Block

CONE ASSEMBLY

PART NO. DESCRIPTION

PINION HOUSING SHIMS A025400170515 Mantle Hold Down Bolt

PART NO. DESCRIPTION A025400180003 Cone Seal Ring

A025402070010 Shim, .010" A025400210000 Upper Radial Bearing

A025402070020 Shim, .020" A025400190000 Cone Radial Bearing Retainer

A025402070025 Shim, .025" A0540030162 Torque Bar

A025402070050 Shim, .050" A025403490004 Torque Bar Pin

A025402030001 Shim, .0747" A004200024430 O-Ring, Mantle Nut

A025402070100 Shim, .100" A025404967000 Sponge Rubber Ring

A025402940001 Shim, .1046" A025400160510 Mantle Hold Down Washer

A025402950000 Shim, .125" A025400140511 Mantle Hold Down Nut

A025402980000 Shim, .1875" A025400150013 Mantle Nut Cap

A025402990000 Shim, .250 A004200023540 O-Ring, Mantle Bolt

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 11-03-2016

Page 71: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

450 MVP CEDARAPIDS® CRUSHER

MANGANESE RETENTION PINION SHAFT ASSEMBLY

PART NO. DESCRIPTION PART NO. DESCRIPTION

A4589080090 Clevis A0540030073 Pinion Shaft

A024805930010 Pin, Clevis Mounting A0540050026 Gear Set

A024805950000 Washer, Clevis Bolt A025400320100 Pinion Gear

A024805940000 Washer, Clevis Bolt A025400050100 Bevel Gear

A024801260000 Nut, Clevis Bolt A4513000244 Bearing Cup

AT105055 Clevis Bolt, 2" A4513000164 Bearing Cone, Inner

AT105056 Washer, Clevis Bolt, 2" A4513000161 Bearing Cone, Outer

AT105057 Washer, Spherical, 2" A024803070000 Key, Lock Ring

AT105058 Nut, Spherical, 2" A024804370000 Pinion Nut Lock

A024800340000 Pinion Locknut

MANGANESE ARRANGEMENTS A024805610000 Wear Ring Seal

PART NO. DESCRIPTION A004200023440 O-Ring

A0540030020 Mantle, Coarse A024805600000 Seal Housing

A0540030021 Mantle, Fine A45200291 Oil Seal

A054003002001 Mantle, Medium A004200024740 O-Ring

A0540030015 Liner, Coarse A004200024520 O-Ring

A0540030016 Liner, Medium

A0540030017 Liner, Medium Fine

A0540030018 Liner, Fine RELIEF PISTON ASSEMBLY

A0540030019 Liner, Extra Fine PART NO. DESCRIPTION

A0540030117 Liner, Medium Fine A024800780000 Piston Assembly - Complete

A003320000525 Spiral Retaining Ring

FINAL ASSEMBLY A024800830000 Seal

PART NO. DESCRIPTION A024800840000 Backup Seal

A0540030253 Guard, Strut MVP450X A024800850000 Wear Ring

A0540030248 Pin, Rotation Stop A024800810000 Piston Core

A002012753250 Bushing, Rotation Stop

A04431789 Guard, Strut

LUBRICATION ASSEMBLY

PART NO. DESCRIPTION

A4525200969 Valve Thermal Bypass

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 11-03-2016

Page 72: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

550 MVP CEDARAPIDS® CRUSHER

LOWER ASSEMBLY LOCKING CYLINDER

PART NO. DESCRIPTION PART NO. DESCRIPTION

A026603620000 Cone Brake Plate A0480030074 Locking Cylinder Assembly

A0480030054 Guide, Clutch A024806330010 Locking Cylinder Piston

A025401000010 Clutch, Over Running A024806330020 Locking Cylinder Housing

A0450050056 Floating Plate A004201000200 Seal

A004202000000 Wear Ring

TRAMP IRON RELIEF SYSTEM A048000015501 Push Pin

PART NO. DESCRIPTION A004200102220 Seal

A024800580000 Relief Cylinder A0540030031 Cylinder Retainer Clip

A024800620000 Dust Cap A4525950812 O-Ring

A024800550000 Piston Rod

A024800580110 Insert CONE ASSEMBLY

A4525950866 O-Ring PART NO. DESCRIPTION

A003200013340 Crown Seal A0600030118 Torque Bar

A0540030096 Tension Rod A025403490004 Torque Bar Pin

A0540030098 Tension Rod Ear A0600030048 Mantle Washer

A024801480020 Split Coupler Base A0600030018 Mantle Nut

A0540030097 Split Coupler Complete A025404720000 Bolt, Mantle Nut Cap

A024805740000 Spherical Seat A4524012553 O-Ring

A024800640000 Guide Plate

A024800650000 Guide Rod Bushing RELIEF PISTON ASSEMBLY

A024500720000 Relief Valve, 3/8 PART NO. DESCRIPTION

A024800730040 Accumulator Adapter Block A024800780000 Piston Assembly - Complete

A023604230000 Elbow, Adjusting Jack A003320000525 Spiral Retaining Ring

A024800830000 Seal

MANTLE'S AND BOWL LINERS A024800840000 Backup Seal

A0600030001 Mantle, Coarse A024800850000 Wear Ring

A060003000101 Mantle, Medium A024800810000 Piston Core

A0600030002 Mantle, Fine

A0600030003 Liner, Coarse MANGANESE RETENSION

A0600030004 Liner, Medium PART NO. DESCRIPTION

A0600030005 Liner, Medium Fine A4589080090 Clevis

A0600030006 Liner, Fine A024805930010 Pin, Clevis Mounting

A0600030007 Liner, Extra Fine A024805950000 Washer, Clevis Bolt

A024805940000 Washer, Clevis Bolt

PINION SHAFT ASSEMBLY A024801260000 Nut, Clevis Bolt

PART NO. DESCRIPTION

A026604370000 Pinion Nut Lock ROTATION STOP

A024805630000 Pin, Rotation Stop

A002012753250 Bushing, Rotation Stop

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date: 12-10-2013

Page 73: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

00-020-000-0040 087002 VALVE CHRG SCHRADER VLVCON J

00-330-510-0100 079006 RING SNAP SH100STPA (5100-100)

00-331-225-0000 079020 RING RETAINING

00-331-231-0000 079016 RING RET RR231 SMALLEY WH23

00-418-158-1000 060111 SHEAVE 8V 10GR 16.0 OD

00-418-188-1000 060078 SHEAVE 8V 10GR 19.0 OD 18.8 PD

00-418-246-0600 060039 SHEAVE 8V 6GR 24.8 0D 24.6 PD

00-418-246-0800 060011 SHEAVE 8V 8GR 24.8 OD 24.6 PD

00-418-246-1000 060021 SHEAVE 8V 10GR 24.8 OD 24.6PD

00-428-000-1600 060074 V-BELT 8V 1600

00-471-453-0600 060110 BUSHING QD J 3-3/8

00-471-453-1400 060073 BUSHING QD J 3-7/8

00-471-553-0800 060012 BUSHING QD N 3-1/2

00-471-553-1400 060079 BUSHING QD M 3-7/8

00-612-000-0000 020000 MOTOR 1 HP PRELUBE 110908

00-801-020-0480 079015 PIN DOWEL .312 X .750

00-84M-032-0004 087003 VALVE CHECK 1/2

00-871-000-0050 085007 ELEMENT FILTER PALL MICR 25

00-871-000-0110 085010 FILTER MICRON 10

00-871-000-0201 085005 ELEMENT & SEAL FILTER 14.0 25M

00-871-000-0222 080097 SEAL FILTER PARKER #927573

00-871-000-0300 085000 HSG FILTER FAIREY ARLON GA 17

00-871-000-0320 085003 ELEMENT FILTER FAIREY ARLON TX

00-871-000-0400 085004 FILTER ASSY DONALDSON HAK05

00-871-000-0410 085001 ELEMENT FILTER DONALDSON

00-871-000-0420 080006 SEAL OIL FILTER DONALDSON

00-873-000-0000 080024 PUMP LUBE .761 CU IN/REV

00-874-000-0000 020026 THERMO ON 60 DEG OFF 80 DEG.

00-891-000-0001 087000 VALVE 5 GALACCUM

00-891-001-0000 450193 ASSY PORT 1 GAL ACCUM

00-891-001-0010 450014 KIT SEAL 1 GAL ACC W/NUTS

00-891-001-9999 450179 KIT SEAL 1 GAL ACC

00-891-005-0000 450017 ASSY PORT 5 GAL ACCUM

00-891-005-0010 450010 KIT SEAL 5 GAL ACC W/NUTS

00-891-005-9999 450180 KIT SEAL 5 GAL ACC

01-846-004-0020 A018460040020 RUBBER SPONGE MANTLE WASHER

02-360-016-0515 360035 WASHER MANTLE

02-360-036-0752 360248 BRG TIMKIN 752 CUP

02-360-036-0762 360253 BRG TIMKIN 762 CONE

02-360-037-0632 360249 BRG TIMKIN 632 CUP

02-360-037-0644 360250 BRG TIMKIN 644 CONE

02-360-040-0000 540139 KEY OIL PUMP DRIVE GEAR

02-360-072-0000 087004 VALVE RELIEF SHORT BODY 3/8

02-360-072-2000 087005 VALVE RELIEF 1/4

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

Rev Date 11-03-2016 .

Page 74: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-360-075-0000 450185 ASSY BLEEDER (NO PRINT)

02-360-087-0010 086003 PUMP OIL WEBSTER MACH 36

02-360-088-0031 360003 BRKT OIL PUMP WEBSTER

02-360-089-0010 080089 SWITCH FLOW 36

02-360-098-0011 360038 PL FLOATING W/ INSERTS

02-360-100-0001 360036 CLUTCH CONE BRAKE

02-360-126-0000 360006 BOLT NUT ADJ SPHERICAL SEAT

02-360-133-0000 081001 TUBE .250 X .049 HYD

02-360-133-0045 450190 KIT ADJ JACK TUBING

02-360-133-0054 540250 KIT ADJ JACK TUBING NO PRINT

02-360-133-0066 660061 KIT TUBING JACK ADJ

02-360-162-0020 360004 BOLT WASHER ADJUSTING

02-360-166-0013 360037 PL THRUST 36

02-360-172-0010 540226 RETAINER ADJ BOLT

02-360-176-0020 090039 GUARD TOGGLE SHIM

02-360-192-0001 450132 WRENCH MANTLE NUT STD

02-360-197-0000 089001 GAUGE PDI 2.5

02-360-225-0000 090037 MATERIAL BACKING MANGANESE

02-360-241-0002 450113 GUIDE INNER ADJ JACK CYL

02-360-242-0002 360242 GUIDE OUTER OLD STYLE

02-360-243-0010 080013 SEAL ADJ JACK POLY 2500-1

02-360-246-0000 076011 NUT JAM ADJUSTING JACK

02-360-247-0000 070120 CAPSCREW SOC 3/4 10NC X 1-3/4

02-360-281-0000 450006 CONNECTOR FLUID

02-360-300-0010 450175 SWITCH PRESSURE NO DRAWING

02-360-301-0000 085002 ELEMENT FILTER BALDWIN P20 HD

02-360-329-0003 540129 ROLLER SHIM GUARD

02-360-330-0000 540166 ACCUM 1GAL 1.25NPT

02-360-358-0020 360005 CLAMP CYL ALIGNING WASHER

02-360-379-0010 450078 GEAR DRIVEN OIL PUMP

02-360-385-0010 450131 STOP BOWL WEDGE

02-360-399-0000 083055 CLIP MNTG 1/4 TUBE

02-360-408-7000 540164 SEAL FELT MANTLE NUT

02-360-421-0000 083019 4-JBU-S (PARKER)

02-360-422-0000 083018 4-4-FBU-S (PARKER)

02-360-423-0000 083017 4-4-CBU-S (PARKER)

02-360-444-0002 086000 Y-27 PUMP ASSY 110V

02-360-468-0000 360019 KIT SEAL REL CYL 36

02-360-469-0010 360251 KIT SEAL CLAMP CYL

02-360-530-0000 450024 BAG 1 GAL ACCUM

02-360-547-0000 450015 KIT ACCUM CHARGING NO PRINT

02-360-571-0000 546216 BAG 2-1/2 GALLON ACCUMULATOR

02-360-813-0000 090063 OAKUM DARK

02-372-089-0000 089011 SWITCH FLOW 50 GPW

Rev Date 11-03-2016 .

Page 75: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-382-089-0020 080092 SWITCH FLOW VSI 2100

02-450-005-0100 450059 GEAR RING SPIRAL

02-450-007-0001 450007 RING SEAL UPPER WEDGE PL

02-450-008-0011 450008 RING SEAL LOWER WEDGE PL

02-450-014-0522 450057 NUT MANTLE

02-450-015-0000 450053 CAP NUT MANTLE 45 INCH

02-450-016-0520 450056 WASHER MANTLE

02-450-016-7017 450124 WASHER MANTLE FH

02-450-017-0570 450151 BOLT MANTLE (SLOTTED)

02-450-018-0001 450018 RING SEAL CONE

02-450-019-0000 450052 RETAINER BRG RADIAL CONE

02-450-021-0001 450021 BRG RADIAL - use 456156

02-450-022-0004 450128SX MANTLE STANDARD

02-450-023-0010 450127SX LINER BOWL COARSE

02-450-027-0001 450027 PL CVR

02-450-028-0001 450028 FLINGER INNER

02-450-029-0001 450029 FLINGER OUTER

02-450-032-0100 450058 GEAR PINION SPIRAL

02-450-033-0010 450033 SHAFT PINION

02-450-034-0001 450067 LOCKNUT SHAFT PINION

02-450-036-0652 450119 BRG PINION CUP INNER

02-450-036-0663 450120 BRG PINION CONE INNER

02-450-037-0572 450117 BRG PINION CUP OUTER

02-450-037-0581 450118 BRG PINION CONE OUTER

02-450-038-0000 450156 KEY PINION GEAR

02-450-042-0252 A024500420252 GUARD STRUT

02-450-043-0011 450043 RING SEAL BASEFRAME

02-450-046-0001 450068 PIN PUSH BASEFRAME

02-450-048-0022 450139 ASSY BOLT ADJ

02-450-048-0040 450069 BOLT ADJ CONNECT QUICK

02-450-051-0013 450051 BOLT PRESSURE HOLD DOWN

02-450-055-0002 450055 ROD PRESSURE

02-450-061-0000 450170 PL SUPT RELIEF CYL

02-450-062-0000 450171 CVR DUST RELIEF CYL

02-450-062-0010 450044 CVR DUST CYL RELIEF

02-450-069-0001 450194 MANIFOLD TO ACCUM TUBE

02-450-071-0000 540167 ACCUM 5GAL 2NPT LJ STYLE

02-450-072-0000 087001 VALVE RELIEF 3/8

02-450-078-0001 450310 ASSY PISTON PART SALES

02-450-079-0001 080008 SEAL RELIEF CYL 1870-4375 O

02-450-079-0010 080010 SEAL ANCHOR PK CLAMP CY 1870-4

02-450-081-0013 450081 PISTON RELIEF CYL

02-450-082-0001 450082 SLEEVE PISTON

02-450-083-0001 080040 SEAL INNER PISTON 083-0001-Q43

Rev Date 11-03-2016 .

Page 76: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-450-089-0020 080026 SWITCH FLOW 45

02-450-098-0014 450497 FLOATING PLATE W/ INSERTS

02-450-099-0003 450049 SHAFT BRAKE

02-450-100-0001 450062 CLUTCH MORSE PB 12A

02-450-101-0000 450070 KEY CLUTCH INNER

02-450-102-0000 450071 KEY CLUTCH OUTER

02-450-103-0010 450060 HUB BRAKE

02-450-104-0000 450061 PL HUB BRAKE

02-450-111-0000 450072 KEY BRAKE SHAFT

02-450-113-0020 450182 VALVE CONTROL BRAKE PRESSURE

02-450-121-0000 450073 CLAMP MANIFOLD TUBE

02-450-125-0000 450074 NUT ADJ BOLT W/CAP

02-450-126-0000 450075 NUT ADJ BOLT W/SPHERICAL SEAL

02-450-148-0020 450148 CPLR BOLT ADJ 2 SPLITS

02-450-153-0010 450228 RETAINER RADIAL UPPER

02-450-155-7000 450022 BRG UPPER THRUST SEE 406017

02-450-156-0000 450023 BRG LOWER THRUST

02-450-162-0021 450162 WASHER BOLT ADJ

02-450-162-0050 450126 WASHER BOLT ADJ

02-450-166-0003 450166 THRUST PLATE

02-450-169-0000 070166 CAPSCREW HEX 3/4 16NF X 2G8

02-450-177-0000 450076 SEAL SHIM GUARD (NO DRAWING)

02-450-191-0000 450045 WRENCH BOLT NUT ADJ

02-450-201-0001 450133 OBSOLETE

02-450-207-0010 450083 SHIM PINION HOUSING .010

02-450-207-0020 450084 SHIM PINION HOUSING .020

02-450-207-0025 450085 SHIM PINION HOUSING .025

02-450-207-0050 450086 SHIM PINION HOUSING .050

02-450-207-0100 450087 SHIM PINION HOUSING .100

02-450-223-0010 450178 BAR TORQUE

02-450-240-0001 450114 RAM ADJUSTING JACK

02-450-261-0010 089004 GAUGE OIL SIGHT

02-450-274-0022 450000 PISTON CLAMP CYL

02-450-279-0000 080009 SEAL U CUP CLAMP CYL 1870-2

02-450-285-0000 450258 PIN .875 X 2.000

02-450-287-0000 090034 WRENCH ALLEN 7/8

02-450-289-0020 450088 SHIM CWT 1/8

02-450-289-0040 450089 SHIM CWT 1/4

02-450-290-0001 450034 CWT LEADING

02-450-291-0000 450036 CWT HEAVY

02-450-292-0000 450035 CWT LIGHT

02-450-293-0000 450102 SHIM PINION HOUSING .0747

02-450-296-0001 540130 LEG SHIM GUARD

02-450-307-0000 450155 KEY RING LOCK

Rev Date 11-03-2016 .

Page 77: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-450-315-0000 450065 BLOCK MANIFOLD

02-450-339-0010 450108 RETAINER CYL RELIEF

02-450-343-0012 450343 CYL CLAMP

02-450-345-0022 450109 ASSY CLAMP CYL

02-450-346-0006 450116 ASSY ADJUSTING JACK

02-450-346-0040 450003 CYL WELDMENT ADJ JACK

02-450-346-0050 450110 GUIDE OUTER ADJ JACK CYL

02-450-358-0024 450358 WASHER ALIGNING CLAMP CYL

02-450-359-0012 450359 CYL CLAMP INSERT

02-450-362-0007 450050 CONE BRAKE PLATE HARDENED

02-450-366-0000 079005 RING RETAINING SMALLEY-BS-437

02-450-367-0000 079004 RING RETAINING BRG INC-UR262

02-450-378-0001 450077 GEAR DRIVE OIL PUMP

02-450-383-0010 080011 SEAL DUST CLAMP CYL 18939H

02-450-386-0000 450177SX LINER BOWL MEDIUM FINE

02-450-431-7011 450431 RING TORCH

02-450-437-0001 450111 NUT LOCK PINION BRG

02-450-441-0010 450189 GUARD PINION TUNNEL

02-450-467-0013 450134 BAND WEAR WEDGE PL SEAL RG

02-450-468-0000 540005 KIT CYL RELIEF CLASSIC NO DWG

02-450-468-0500 540053 KIT CYL RELIEF RCII (NO DWG)

02-450-469-0001 450115 KIT SEAL CLAMP CYL BEF 1970

02-450-469-0011 450079 KIT SEAL CLAMP CYL

02-450-469-0020 450004 KIT SEAL CLAMP CYL

02-450-470-0000 450005 KIT ADJ JACK CYL OS

02-450-470-0010 450013 KIT SEAL JACK CYL NEW STYLE

02-450-479-0002 450479 SLEEVE BRASS CLAMP CYL

02-450-480-0001 450480 CYL CLAMP CVR THREADED

02-450-484-0002 450030 WRENCH CLAMP CYL

02-450-550-0001 450112 KIT SHIM STACK BASEFRAME

02-450-550-0010 450136 KIT SHIM STACK COMPLETE

02-450-550-0550 450090 SHIM ADJ .062

02-450-551-0000 450091 SHIM ADJ .125 WHITE

02-450-552-0000 450092 SHIM ADJ .188 YELLOW

02-450-553-0000 450093 SHIM ADJ .250 BLACK

02-450-554-0000 450094 SHIM ADJ .313 RED

02-450-555-0000 450095 SHIM ADJ .375 BLUE

02-450-556-0000 450096 SHIM ADJ .500 ORANGE

02-450-557-0000 450097 SHIM ADJ .625 BROWN

02-450-558-0000 450098 SHIM ADJ .750 PURPLE

02-450-559-0000 450099 SHIM ADJ .875 GREY

02-450-560-0000 450100 SHIM ADJ 1.000 GREEN

02-450-561-0000 450101 SHIM ADJ 1.500 ALUMINUM

02-450-571-0000 450020 BAG 5 GAL ACCUM

Rev Date 11-03-2016 .

Page 78: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-450-583-0010 089000 ASSY PUMP COUPLER PRE-LUBE

02-450-585-0001 080030 PUMP ADAPTOR (FIL-4AA)

02-450-589-0000 080043 COVER PLATE PUMP ADAPTOR

02-450-609-0000 450026 SYSTEM RELIEF FERRULE THRD

02-450-610-0000 450173 NUT 32 SIZE SP MACHINED RECE

02-450-611-0000 080005 ELBOW 32CU-S

02-450-612-0000 083020 32EBU-S (PARKER) - SEE TEXT

02-450-624-0000 450138 KIT INTERN LUBE (PART SALES)

02-450-625-0000 450608 ASSY HEATER 2000W 120V 45RC

02-450-628-0000 450163 KIT GUIDE RING (NO PRINT)

02-450-816-0020 450012 KIT OIL FILTER

02-540-005-0020 540188 SEE JCI P/N 540040

02-540-005-0100 540040 GEAR RING SPIRAL

02-540-007-0003 540007 RING SEAL PL WEDGE UPPER

02-540-008-0001 540008 RING SEAL PL WEDGE LOWER

02-540-009-0024 540110 SEE JCI P/N 540141

02-540-010-7010 540105 HOPPER SHORT USE W/INVERT ACCU

02-540-012-0070 540256 BONNET SUPT LINER

02-540-014-0511 540094 MANTLE NUT

02-540-014-7524 540120 NUT MANTLE HOLD DOWN FH O S

02-540-015-0013 540102 CAP MANTLE NUT

02-540-016-0510 540037 WASHER MANTLE

02-540-016-7024 540297 WASHER MANTLE FH

02-540-017-0570 540016 BOLT MANTLE SLOTTED

02-540-018-0003 540018 RING SEAL CONE

02-540-019-0000 540165 RADIAL RETAINER CONE UPPER

02-540-021-0000 546350 BRG UPPER RADIAL

02-540-022-0103 540101SX MANTLE COARSE XLIFE

02-540-023-0103 540113SX LINER COARSE EXTRA LIFE

02-540-027-0000 540027 PL CVR

02-540-028-0003 540028 FLINGER INNER

02-540-029-0001 540029 FLINGER OUTER

02-540-032-0020 540187 SEE JCI P/N 540039

02-540-032-0100 540039 GEAR PINION SPIRAL

02-540-033-0010 540252 SHAFT PINION 54 SHORT

02-540-034-0000 540045 LOCKNUT PINION SHAFT

02-540-035-0000 540097 BRG PINION CUP 854

02-540-036-0010 540096 BRG PINION CONE INNER 861

02-540-037-0010 540095 BRG PINION CONE OUTER 864

02-540-038-0000 540138 KEY PINION GEAR

02-540-042-0252 A025400420252 GUARD STRUT

02-540-043-0002 540043 BASEFRAME RING SEAL

02-540-044-0003 540286 CLAMP RING DRLD MADE FROM BURN

02-540-046-0001 540046 PIN PUSH

Rev Date 11-03-2016 .

Page 79: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-540-048-2000 540183 BLOCK ADJ BOLT O S

02-540-048-4000 450048 BOLT ADJ OLD STYLE

02-540-048-7023 540047 ASSY BOLT ADJUSTING

02-540-051-0023 540051 PRESSURE RING HOLD DOWN BOLT

02-540-055-0002 540055 ROD PRESSURE

02-540-058-0001 540503 CYL RELIEF 4.750 ID

02-540-062-0010 540520 CAP DUST RELIEF CYL

02-540-069-0011 540151 TUBE MANIFOLD TO ACCUMULATOR

02-540-077-0000 546351 BRG LOWER RADIAL

02-540-081-0010 540158 CORE PISTON

02-540-083-0000 080046 SEAL RELIEF CYLINDER 37504500

02-540-084-0000 080041 SEAL RELF CYL RCII 37504500MB

02-540-085-0000 080042 SEAL SPLT RELF CYL RCII 5250

02-540-086-0000 540235 KEY OIL PUMP WEBSTER NO DWG

02-540-087-0000 086004 PUMP LUBE WEBSTER BI-DIREC

02-540-087-0005 086009 PUMP OIL WEBSTER RH

02-540-087-0010 540048 PUMP OIL WEBSTER

02-540-088-0010 540088 BRKT OIL PUMP

02-540-089-0010 080027 FLOW SWITCH 54

02-540-090-0070 540012 KIT PRELUBE PUMP 115V NO PRIN

02-540-099-0007 540154 SHAFT CONE BRAKE

02-540-100-0010 540049 CLUTCH BRAKE

02-540-101-0000 540050 KEY CLUTCH

02-540-116-0002 540224 ASSY MANIFOLD WELD 3 HD

02-540-123-0010 540505 TUBE RELIEF MANIFOLD

02-540-123-0140 540306 ASSY RELIEF MANIFOLD TUBE

02-540-137-0130 540254 GASKET HEATER

02-540-153-0010 540159 RADIAL RACE RETAINER UPPER

02-540-155-7000 546352 BRG UPPER THRUST

02-540-156-0000 546353 BRG LOWER THRUST

02-540-166-0008 540116 PL THRUST 54

02-540-177-0000 540131 SEAL SHIM GUARD NO DRAWING

02-540-192-0000 540014 WRENCH MANTLE NUT STD

02-540-196-0030 540128 SHIM GUARD

02-540-201-0000 540104 OBSOLETE SEE TEXT

02-540-207-0005 540234 SHIM PINION HOUSING .005

02-540-207-0010 540056 SHIM PINION HOUSING .010

02-540-207-0020 540057 SHIM PINION HOUSING .020

02-540-207-0025 540058 SHIM PINION HOUSING .025

02-540-207-0050 540060 SHIM PINION HOUSING .050

02-540-207-0100 540061 SHIM PINION HOUSING .100

02-540-223-0006 540062 TORQUE BAR HARDENED

02-540-228-7030 540124 PL DISTRIBUTOR

02-540-228-8000 A025402288000 PL DISTRIBUTOR FH 8000

Rev Date 11-03-2016 .

Page 80: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-540-228-8010 540277 PL DISTRIBUTOR 8010

02-540-284-0030 450176 ROTATION STOP TEXAS STY SET=1

02-540-284-0040 450064 ROTATION STOP UPPER WELD ON

02-540-284-0050 450164 ROTATION STOP LOWER WELD ON

02-540-284-0120 540148 OBSOLETE - CONSULT JCI

02-540-284-0130 540149 OBSOLETE - CONSULT JCI

02-540-285-0010 540302 PIN 1.500 X 2.000

02-540-287-0000 090035 WRENCH ALLEN 1

02-540-289-0020 540065 SHIM CWT .125

02-540-289-0040 540066 SHIM CWT .250

02-540-289-0140 540506 SHIM PL WEAR CTRWT ELJ

02-540-290-0001 540034 CWT LEADING CLASSIC

02-540-290-0020 540031 CWT LEADING 54II

02-540-291-0000 540033 CWT HEAVY CLASSIC

02-540-291-0020 540030 CWT 54II

02-540-292-0000 540032 CWT LIGHT CLASSIC

02-540-293-0001 540067 SHIM PINION HOUSING .0747

02-540-294-0001 540068 SHIM PINION HOUSING .1046

02-540-295-0000 540069 SHIM PINION HOUSING .120

02-540-298-0000 540071 SHIM PINION HOUSING .1875

02-540-299-0000 540072 SHIM PINION HOUSING .250

02-540-304-0001 540184 BOLT RETAINER ADJ BOLT W/BLO

02-540-305-0000 540073 SHIM PINION HOUSING .045

02-540-307-0000 540140 KEY LOCK RING

02-540-309-0000 540176 KEY DRIVE PINION SHAFT

02-540-317-0000 540161 KEY CONE BRAKE PLATE

02-540-319-7511 540121 BOLT MANTLE HOLD DOWN FH O S

02-540-324-7001 540163 GASKET DISTRIBUTOR PLATE

02-540-362-0007 540074 CONE BRAKE PLATE HARDENED

02-540-378-0000 540267 GEAR DRIVE OIL PUMP 58TOOTH

02-540-378-0010 540098 GEAR DRIVE OIL PUMP 62TOOTH

02-540-379-0000 540099 GEAR DRIVE OIL PUMP 21TOOTH

02-540-382-7000 540015 LUG LOCKING FH

02-540-382-8000 540288 LUG LOCKING FH 8500 SERIES

02-540-382-8010 540328 LUG FINE HEAD LOCKING

02-540-386-0110 540114SX LINER MEDIUM FINE EXTRA LIFE

02-540-389-0000 540006 SHIM OIL PUMP MT -.005

02-540-389-0010 540009 SHIM OIL PUMP MT - .010

02-540-391-0010 540025 CVR FILTER OIL

02-540-392-0000 450137 CAP PROTECTOR ACCUM

02-540-430-0010 540017 CLUTCH GUIDE RING

02-540-431-7012 540431 RING TORCH

02-540-437-0002 540137 LOCKNUT PINION

02-540-441-0010 540221 PL WEAR TUNNEL PINION 54

Rev Date 11-03-2016 .

Page 81: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-540-452-0020 540327 HEATER MACHINED 2000W 120V

02-540-452-0030 540533 HEATER MACHINED 2000W 220V

02-540-467-0014 540024 WEAR BAND LOWER WP SEAL RING

02-540-472-0000 070052 CAPSCREW SOC 1-1/2 6NC X 2-1/4

02-540-488-0100 540115SX LINER BOWL MEDIUM XLIFE

02-540-494-0010 540011 BRKT OIL FILTER DONALDSON

02-540-494-0020 540041 BRKT OIL FILTER

02-540-495-0000 540290 LINER COARSE ENLARGE FEED OPEN

02-540-590-0030 540127 PUMP AUX & HORN MOUNT O S

02-540-625-0000 540433 ASSY HEATER 2000W 115V ELJAY

02-540-626-0000 450011 KIT WARNING HORN

02-540-627-0000 540435 KIT RECIRCULATION OIL

02-540-629-0000 083074 NEEDLE OIL SAMPLER W/TUBING

02-540-650-0000 450257 PIN .500 X 1.000

02-540-816-0020 540035 KIT LUBE COMPLETE 54 NO DWG

02-540-900-0030 701104 KIT MNTG CRUSHER

02-600-016-0010 A026000160010 WASHER MANTLE HOLD DOWN

02-600-033-0010 540044 SHAFT PINION

02-600-144-0000 540191 DIPSTICK

02-660-003-0000 660007 LINER BOLT EYE MACHINED

02-660-007-0010 660053 RING SEAL PL WEDGE UPPER

02-660-008-0010 660040 RING SEAL PL WEDGE LOWER

02-660-013-0020 A026600130200 RETAINER BEARING

02-660-016-0010 660000 WASHER MANTLE

02-660-018-0010 660054 RING SEAL CONE

02-660-021-0000 660001 BRG RADIAL UPPER

02-660-027-0000 660028 PL CVR PINION

02-660-028-0000 660029 FLINGER INNER

02-660-029-0000 660030 FLINGER OUTER

02-660-033-0010 660023 SHAFT PINION

02-660-034-0000 660027 LOCKNUT PINION SHAFT

02-660-036-0000 660008 BRG CONE

02-660-037-0000 660009 BRG CONE

02-660-043-0000 660041 RING SEAL BASEFRAME

02-660-057-0000 660033 PIN CLEVIS

02-660-077-0000 660002 BRG RADIAL LOWER

02-660-089-0010 080062 SWITCH FLOW

02-660-155-0000 660003 BRG THRUST UPPER

02-660-156-0001 660004 BRG THRUST LOWER

02-660-177-0000 660047 SEAL GUARD SHIM 66

02-660-246-0000 660045 NUT JAM ADJ JACK 66

02-660-284-0000 660037 STOP ROTATION UPPER

02-660-284-0010 660038 STOP ROTATION LOWER

02-660-307-0000 660026 KEY LOCK NUT PINION

Rev Date 11-03-2016 .

Page 82: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® ROLLERCONE® and RCII® CRUSHERS

Cedarapids, Inc., manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM and CEDARAPIDS® are trademarks of Terex USA, LLC

OEM PART NO. JCI PART NO DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

02-660-334-0000 084066 O-RING NF20050 66 PINION HSG

02-660-346-0006 660014 ASSY JACK ADJ 66

02-660-346-0050 660021 SPACER PISTON CYL JACK ADJ 66

02-660-346-0100 660015 RAM JACK ADJ 66

02-660-346-0140 660019 GUIDE OUTE CYL JACK ADJ 66

02-660-378-0000 660032 PUMP OIL FEAR DRIVEN 71 TOOTH

02-660-379-0000 660031 PUMP OIL GEAR DRIVEN 45 TOOTH

02-660-437-0020 660025 LOCKNUT PINION

02-660-467-0000 660055 BAND WEAR LOWER WP

02-660-470-0000 660034 KIT SEAL JACK ADJ

02-660-494-0031 540038 SPACER FILTER RBBR

02-660-494-0032 540093 SPACER SUPT OIL FILTER HSG

02-720-004-0010 660010 WASHER BOLT CLEVIS

02-720-015-0000 660012 CAP NUT MANTEL 72 CRUSHER

02-720-017-0000 660048 MANTLE BOLT, 66"

02-720-037-5925 660013 CUP BRG

02-720-087-0010 086001 PUMP OIL 72 CRUSHER

04-70-0002-0560 540236 ANGLE CLIP 2X2X3/8

04-74-0000-0680 450122 ASSY HORN 115V NO PRINT

Rev Date 11-03-2016 .

Page 83: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® 3 SHAFT HORIZONTAL SCREENS

OEM PART NO. JCI PART NO. DESCRIPTION

0314433002 620144 ASSY CHANNEL MOUNT MOROR LH

0314433003 620143 ASSY CHANNEL MOUNT MOTOR RH

0314433005 620145 SEE JCI P/N 622730

0315400382 620113 BRKT TAKE-UP MOUNT MOTOR

00-424-128-0000 060001 V-BELT D 128

00-424-144-0000 060010 V-BELT D 144

00-424-158-0000 060002 V-BELT D 158

00-424-162-0000 060034 V-BELT D 162

00-424-173-0000 060277 V-BELT D 173

00-471-282-0000 060009 BUSHING QD SF 2

00-471-282-0200 060003 BUSHING QD 2-1/8 SF

00-701-048-0020 076007 HUCKBOLT COLLAR 3LC-2R-24

00-844-024-0001 080036 PLUG PIPE 3/8NPT SOC HEAD

00-845-016-0001 080035 PLUG PIPE 1/4 SQ HD BLACK

00-845-024-0001 080065 PLUG PIPE 3/8 SQ HEAD BLACK

00-845-100-1001 080032 PLUG MAGNETIC 1

00-848-048-0167 080034 5406-12-04

00-84B-132-0481 080033 REDUCER BELL 1 1/2 TO 3/4

01-200-000-0616 090016 NOZZLE SRY 1/4 ORIFICE 3/8NPT

01-360-000-0001 090028 SPRG RBBR 5-1/2 X 2 X 7

01-360-000-0002 090012 SPRG RBBR 7-1/2 X 3-1/2 X 10

01-372-206-2000 090008 SPRG BELT TENSIONER

01-372-412-7001 090058 SPRG 7/8 X 4 X 12 1-5/16 PITC

01-372-412-7002 090059 SPRG .9375 X 4 ID X 12 X 1.375

01-372-412-8001 090060 SPRG 1 X 4 X 12 1.4375P

01-372-412-8002 090061 SPRG 1 X 4-1/2 X 12 1-3/8 PITC

01-372-412-8004 090054 SPRG 1-1/16X4-1/2X12-1/2

01-410-000-0000 616164 CHANNEL RUB 1/2HI 1/2RAILS

01-844-000-0001 090009 SEALER SILICONE TUBE

01-874-000-0008 090013 ASSY LOCKING SOCKET 8MM HEX

03-100-165-5000 516097 GUARD TUBE 5 26/32 JCI

03-100-165-5010 514102 GUARD TUBE 5 24 JCI

03-100-165-6000 620255 GUARD TUBE 6 32 JCI

03-100-165-7000 720056 GUARD TUBE SHAFT 7 38 JCI

03-120-063-5009 514078 TUBE SHAFT MACHINED 24JCI 5

03-120-079-0020 080031 CAP BREATHER 4H6112

03-120-080-0020 620173 PULLEY BELT TENSIONER

03-120-084-0021 620794 TENSIONER ARM RH/LH

03-120-084-0030 620121 ARM SWING BELT TENSIONER L/R

03-120-084-0500 620793 TENSIONER ARM LH EJ 620794

03-120-086-0030 620174 OBSOLETE SEE 621621 BRACKET

03-120-089-0010 090006 BRG FLT 63062RS BELT TEN

03-120-239-0000 620014 TAB BOLT KEY

03-120-242-0020 620005 TAB DISC

03-120-287-0000 514103 STRAP GUARD TUBE 24

03-124-003-0020 514016 SPINDLE 24 FINISH MACHINE

Rev Date: 1-25-2012 .

Page 84: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® 3 SHAFT HORIZONTAL SCREENS

03-124-008-0000 090019 BRG SCREEN 24 SIZE 2224K

03-124-016-0030 514018 COLLAR SEAL OIL 24

03-124-018-0002 514015 RING GLAND 24 (MAKES 7)

03-124-060-0010 514046 WRENCH TIMING 24

03-124-064-0000 514031 SHEAVE 19.4 PD 24

03-124-143-4050 414001 SHAFT DRIVE 24 LA 4FT

03-124-143-5032 514019 SHAFT DRIVE 24 ECC 5FT

03-124-143-5040 514061 SHAFT DRIVE 24 CON 5FT

03-124-143-5050 514027 SHAFT DRIVE 24 LA 5FT

03-124-144-4040 414002 SHAFT TIMING 24 LA 4FT

03-124-144-5021 514036 SHAFT TIMING 24 ECC 5 FT

03-124-144-5030 514062 SHAFT TIMING 24 CON 5FT

03-124-144-5040 514026 SHAFT TIMING 24 LA 5FT

03-124-145-0070 514021 HUB GEAR SIDE 24 LA

03-124-147-0060 514022 HUB IMPULSE SIDE 24 LA

03-124-157-0010 514020 KEY DRIVE 24

03-124-158-0001 514014 SLEEVE TAPERED EXCENTRIC 24

03-124-158-0010 514017 BUSH TAPERED 24 CONCENTRIC

03-124-159-0012 514038 KEY ECCENTRIC HUB

03-124-171-0002 514010 DISK GEAR 24

03-124-192-0010 514077 BOLT KEY 24

03-124-259-0000 514037 ASSY SEAL ECC INNER & OUT RH

03-124-266-0040 514030 HOUSING SEAL OIL 24

03-124-267-0000 514045 WASHER SEAL OIL

03-124-269-0000 080077 SEAL OIL 24 CHICAGO RAWHID#201

03-124-269-0010 080049 SEAL OIL

03-124-269-0030 080070 SEAL OIL 24LA (JM11814 LPDW

03-124-270-0000 080072 SLEEVE WEAR 24 CONC (J-1107)

03-124-270-0010 080071 SLEEVE WEAR 24LA (J-1115)

03-124-271-0000 514025 DISK IMPULSE 24

03-124-299-0000 090082 ASSY LOCKING 24

03-124-300-0000 514032 BAR LOCATION WT

03-124-303-0010 514029 RING BARRIER 24

03-126-003-0030 516000 SPINDLE FINISH MACHINE

03-126-008-0000 090020 BRG SCREEN 26 SIZE 22226

03-126-016-0020 516128 COLLAR HOUSING SEAL OIL ECC

03-126-018-0001 516078 RING GLAND 26 (MAKES 7)

03-126-052-0050 620055 CVR CASE GEAR SIDE 32

03-126-053-0060 620068 CVR CASE IMPULSE SIDE 32

03-126-063-5006 516007 TUBE SHAFT MACHINED

03-126-063-6006 620054 TUBE SHAFT MACHINED

03-126-064-0004 516297 SHEAVE ECC 19.4 PD JCI

03-126-064-0010 516298 SHEAVE CONC 19.4 PD JCI

03-126-064-0020 516045 SHEAVE 19.4PD JCI 26 1200MOTOR

03-126-143-5040 516333 SHAFT DRIVE 5FT CONC

03-126-143-5050 516008 SHAFT DRIVE 26 LA 5FT

03-126-143-6050 616072 SHAFT DRIVE 26 & 28 LA 6FT

Rev Date: 1-25-2012 .

Page 85: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® 3 SHAFT HORIZONTAL SCREENS

03-126-144-5030 516334 SHAFT TIMING 5FT CONC

03-126-144-5040 516009 SHAFT TIMING 26 LA 5FT

03-126-144-6040 616073 SHAFT TIMING 26 & 28 LA 6FT

03-126-145-0060 516149 GEAR HUB SIDE 26FSG CONC-PR SA

03-126-145-0070 516001 HUB GEAR SIDE

03-126-147-0060 516002 HUB IMPULSE

03-126-157-0010 516320 KEY HUB ECC

03-126-158-0002 516226 BUSH TAPERED ECC N 12

03-126-158-0010 516055 SLEEVE TAPER CONCENTRIC 26

03-126-160-0002 516225 BUSH DRIVE TAPERED ECC N 1G

03-126-168-0000 620025 CVR REMOVAL PLUG

03-126-171-0010 516004 DISK GEAR

03-126-172-0000 620030 ASSY COVER TIMING

03-126-206-0001 080038 BUSH BELT TENSIONER RBBR

03-126-259-0000 516233 ASSY SEAL INNER & OUTER (RH)

03-126-259-0500 516299 ASSY SEAL INNER & OUTER (LH)

03-126-266-0010 516224 COLLAR HOUSING SEAL OIL 26

03-126-266-0030 516010 HOUSING SEAL OIL

03-126-267-0000 620258 WASHER SEAL OIL (PAINT ONLY)

03-126-269-0000 080079 SEAL OIL CONC NATIONAL 411376

03-126-269-0010 080063 SEAL TAPER BORE 26

03-126-269-0020 080045 SEAL OIL 13137

03-126-270-0000 080064 SEAL WEAR SLEEVE TAPER BORE 26

03-126-270-0010 080044 ASSY WEAR SLEEVE 26 LOCKING

03-126-271-0000 516005 DISK IMPULSE

03-126-281-5000 516312 SHAFT DRIVE 5 ECC

03-126-282-5000 516317 SHAFT TIMING ECC

03-126-283-0000 516319 KEY HUB DRIVE ECC

03-126-299-0000 090021 ASSY LOCKING 26

03-126-300-0000 620368 BAR LOCATION WT

03-126-303-0010 516011 RING BARRIER

03-128-008-0000 090078 BRG SPHERICAL 28

03-128-167-6001 620455 SHEAVE VP11.8-14.2PD SF HUB

03-128-192-0010 620011 BOLT KEY

03-132-003-0020 620001 SPINDLE FINISH MACHINE

03-132-008-0000 090001 BRG SPHERICAL 32

03-132-064-0000 620140 SHEAVE 19.4PD JCI 32 1200MOTOR

03-132-143-5010 620334 SHAFT DRIVE 32 LA 5FT

03-132-143-6020 620007 SHAFT DRIVE 32 LA 6FT

03-132-144-5010 516172 SHAFT TIMING 32 LA 5FT

03-132-144-6020 620015 SHAFT TIMING 32 LA 6FT

03-132-145-0010 620006 HUB GEAR SIDE

03-132-147-0010 620009 HUB IMPULSE SIDE

03-132-158-0000 620198 SLEEVE TAPER CONCENTRIC 32

03-132-171-0000 620008 DISK GEAR

03-132-266-0010 620453 HOUSING SEAL OIL CONC

03-132-266-0030 620024 HOUSING SEAL OIL

Rev Date: 1-25-2012 .

Page 86: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® 3 SHAFT HORIZONTAL SCREENS

03-132-269-0000 080080 SEAL OIL FED MOGUL 415007

03-132-269-0010 080054 SEAL JM 12141 AIR OIL O/S

03-132-269-0020 080002 ASSY SEAL LOCKING 32

03-132-270-0000 080052 SLEEVE WEAR CONC 32

03-132-270-0010 080003 ASSY WEAR SLEEVE LOCKING 32

03-132-271-0000 620069 DISK IMPULSE OUTER

03-132-299-0000 090002 ASSY LOCKING 32

03-132-303-0010 620018 RING BARRIER

03-138-003-0000 720126 SPINDLE ELJAY REPLACEMENT

03-138-008-0000 090083 BRG 38 22238KMW33C3

03-138-064-0000 720089 SHEAVE 19.4 PO 38JCI MACHIN

03-138-068-0000 720006 TUBE SHAFT FINAL MACH 38

03-138-143-7000 720009 SHAFT DRIVE 38 LA 7FT

03-138-144-7000 720010 SHAFT TIMING 38 LA 7FT

03-138-145-0000 720011 HUB GEAR SIDE 38

03-138-147-0000 720012 HUB IMULSE SIDE 38

03-138-167-0000 720183 SHEAVE VP11.8-14.2PD E HUB

03-138-171-0000 720013 DISK GEAR 38

03-138-266-0000 720017 HOUSING SEAL OIL 38

03-138-269-0000 080075 SEAL OIL 38 13136 LPDW JONSMA

03-138-270-0000 080076 SLEEVE WEAR 38 NATIONAL J1125

03-138-271-0000 720014 DISK IMPULSE 38

03-138-287-0000 720055 STRAP GUARD TUBE SHAFT 38

03-138-299-0000 090084 ASSY LOCKING 38 3.500BOREX130M

03-138-303-0000 720008 RING BARRIER 38

03-152-516-0350 616218 CHANNEL DD 8 T&B

03-152-516-0360 616219 CHANNEL DD 8 CENTER

03-152-620-0430 620724 ASSY DD CHANNEL TOP-BOT

03-152-620-0440 620727 ASSY DD CHANNEL CENTER

03-152-620-0890 620286 TRAY BALL

03-160-500-0031 516315 LIP DISCHE 5 X 4

03-160-600-1442 620236 LIP DISCH 6 X 4

03-162-000-0061 516229 PAD SPRG 4.5 SPRG WIRE

03-162-000-0230 620044 PAD SPRING MARSHME

03-162-000-0240 620189 CONV PAD SPRING 4.5

03-162-000-3940 090010 BAND TENSION 14

03-162-000-3950 620124 BRKT ADJ TAGLINE

03-162-000-3960 620048 BRKT BASKET TAGLINE

03-162-000-3970 620046 BRKT TAKE-UP TAG LINE

03-162-000-3980 620125 BRKT TAGLINE END

03-162-000-3990 080028 BUSH 1.250 OD X.750 ID X3.

03-166-000-0030 620142 MOUNT MOTOR

03-170-000-0230 516027 PLUG WT 2.375 X 5.500

03-170-000-0241 078033 SQUARE WASHER

03-170-000-0320 090004 RBBR 2.500 O.D. X 4.500

03-170-000-0520 516013 STRAP WT

03-170-000-0560 620017 STRAP WT

Rev Date: 1-25-2012 .

Page 87: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

CEDARAPIDS® 3 SHAFT HORIZONTAL SCREENS

03-170-000-0970 620076 CHANNEL RBBR 1/2HI 3/8RAILS

03-170-000-1140 620100 CLAMP COIL SPRG BELT TENSIONER

03-170-000-1330 620732 DRAWPL 5IN X 4FT

03-170-000-1340 620408 DRAWPL LJ 5 x 60

03-170-000-1350 620733 DRAWPL 5IN X 6FT

03-170-000-1360 620734 DRAWPL 5IN X 7FT

03-170-000-1370 620735 DRAWPL 5IN X 8FT

03-170-000-1450 620016 PLUG WT

03-170-000-1730 616150 PAD SNUBBER

03-170-000-4521 616213 CUP SNUBBER

03-170-000-4562 616212 PL BACKING PLATE

03-170-000-4620 620480 STRAP DD CENTER H/D 8

03-170-000-4680 620479 STRAP DD TOP & BOTTOM H/D 8

03-170-000-4691 620407 STRAP HOLD DOWN 10 TOP&BT

03-170-000-4701 620549 STRAP HOLD DOWN 10 CENTER DECK

03-170-000-5320 516144 KIT 26 SHAFT LA CONV 5

03-170-000-5330 514011 KIT 24 SHAFT LA CONVERSION 5

03-170-000-5340 414003 KIT 24 SHAFT LA CONVERSION 4FT

03-170-000-5350 620622 KIT 32 SHAFT LA CONVERSION 6

03-170-000-5500 514035 OBSOLETE - SEE JCI P/N 514387

03-170-000-5510 516102 OBSOLETE - SEE JCI P/N 516584

03-170-000-5520 620171 OBSOLETE - SEE JCI P/N 616537

03-170-000-6510 514047 GEAR SET 24 PART SALES

03-170-000-6520 620287 SET GEAR 26 28 32 PARTS SALES

03-170-000-6530 720172 SET GEAR 38 PART SALES

03-170-000-6610 620090 ASSY BELT TENSIONER RH/LH

03-170-000-6620 620294 KIT B/T BRGS & PLT ONLY P-BLO

03-170-000-7250 620230 KIT SPRGS WIRE TO 8 SPRGS RUB

03-170-000-7260 620190 KIT SPRINGS WIRE TO 4 RUB SPRG

03-170-000-7290 620194 KIT ASSY TAGLINE

03-170-000-9220 516101 CONV 26 SHAFT LOCKING ASSY

03-170-000-9230 516143 KIT 26 SHAFT LA CONV 6

03-170-600-0990 620238 ASSY BOX FEED 6 X 24

03-180-000-0060 620203 use 622023

03-182-516-0000 516074 PIPE SPRAY 5FT 1-1/4 NOZZLE

03-182-600-0000 620310 PIPE SPRAY 6FT 1-1/4 NOZZLE

03-272-020-0000 090029 BUSH TORSION BAR

03-770-000-0070 070035 BOLT CARRIAGE 5/8 11NC X4-1/2

03-770-000-0080 070053 TEE-BOLT 5/8 11 NC X 4-1/4

03-770-000-0110 620302 BOLT KEY 5/8 X 5

03-770-000-0120 620303 WEDGE BOLT KEY

03-770-000-4280 078012 WASHER SIDEPLATE

03-770-024-0000 620033 WASHER ALIGNING PLATED

04-70-0002-0191 620134 HANDLE

04-70-1130-0460 090133 SPRG 5/8 X 1-5/8 ID X 8 X 1

4589-0255-44 620251 WASHER SPH 7/8 ID FOR 3/4BLT

A0945078306 090247 SPRG 1-1/8X6-1/8X12 2PITCH

Rev Date: 1-25-2012 .

Page 88: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1165 PEGSON JAW CRUSHER

JAW DIE - STANDARD CHEEK PLATES

PART NO. PART NO. DESCRIPTION

A600/2011 Standard Fixed Jaw A600/2014 Cheek Plate, Upper, LH

A600/2012 Standard Swing Jaw A600/2015 Cheek Plate, Upper, RH

A600/2021 Standard Fixed Wedge A600/2016 Cheek Plate, Lower, LH

A600/2022 Standard Swing Wedge A600/2017 Cheek Plate, Lower, RH

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt TOGGLE PLATE

A2217-0015 Nut, Nylock, Wedge Bolt PART NO. DESCRIPTION

A600/2025 Toggle Plate

JAW DIE - SUPERTOOTH

PART NO. DESCRIPTION

A600/2148 Supertooth Fixed Jaw

A600/2149 Supertooth Swing Jaw

A600/2150 Supertooth Fixed Wedge

A600/2151 Supertooth Swing Wedge

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt

A2217-0015 Nut, Nylock, Wedge Bolt

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 6-20-2016 .

Page 89: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

1180 PEGSON JAW CRUSHER

JAW DIE - STANDARD CHEEK PLATES

PART NO. PART NO. DESCRIPTION

A600/3011 Standard Fixed Jaw A600/3014 Cheek Plate, Upper, LH

A600/3012 Standard Swing Jaw A600/3015 Cheek Plate, Upper, RH

A600/3064 Standard Fixed Wedge A600/3016 Cheek Plate, Lower, LH

A600/3022 Standard Swing Wedge A600/3017 Cheek Plate, Lower, RH

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt TOGGLE PLATE

A2217-0015 Nut, Nylock, Wedge Bolt PART NO. DESCRIPTION

A600/3025 Toggle Plate

JAW DIE - SUPERTOOTH

PART NO. DESCRIPTION

A600/3300 Supertooth Fixed Jaw

A600/3301 Supertooth Swing Jaw

A600/3302 Supertooth Fixed Wedge

A600/3303 Supertooth Swing Wedge

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt

A2217-0015 Nut, Nylock, Wedge Bolt

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 6-20-2016 .

Page 90: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

400S PEGSON JAW CRUSHER

JAW DIE - STANDARD CHEEK PLATES

PART NO. PART NO. DESCRIPTION

ACR005-008-001 Standard Fixed Jaw ACR005-051-001 Cheek Plate, Upper, LH

ACR005-007-001 Standard Swing Jaw ACR005-052-001 Cheek Plate, Upper, RH

ACR005-010-001 Standard Fixed Wedge ACR005-053-001 Cheek Plate, Lower, LH

ACR005-009-001 Standard Swing Wedge ACR005-054-001 Cheek Plate, Lower, RH

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt TOGGLE PLATE

A2217-0015 Nut, Nylock, Wedge Bolt PART NO. DESCRIPTION

ACR005-055-001 Toggle Plate

JAW DIE - SUPERTOOTH

PART NO. DESCRIPTION

ACR005-068-001 Supertooth Fixed Jaw

ACR005-067-001 Supertooth Swing Jaw

ACR005-070-001 Supertooth Fixed Wedge

ACR005-069-001 Supertooth Swing Wedge

A325/28 Bolt, Wedge, Fixed

A325/27 Bolt, Wedge, Swing

A310/23 Washer, Wedge Bolt

A311/11 Washer, Fiber, Wedge Bolt

A2217-0015 Nut, Nylock, Wedge Bolt

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Hardware is available-please inquire Rev Date 6-20-2016 .

Page 91: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

SYMONS CONE CRUSHER MANGANESE AND ASSOCIATED

PARTS

PART NUMBER DESCRIPTION

A2747-5941 MANTLE NUT COVER

A3041-2875 FEED DISTRIBUTOR

A4829-1921 CONCAVE

A4829-3541 CONCAVE

A4829-4351 CONCAVE

A4829-4706 UPPER CONCAVE

A4829-5026 CONCAVE

A4829-5161 CONCAVE

A4829-6511 MANTLE

A4829-6530 CONCAVE

A4829-6544 CONCAVE

A4829-6576 CONCAVE

A4829-6646 CONCAVE

A4829-7591 CONCAVE

A4829-8131 BOWL LINER

A4829-8494 UPPER CONCAVE

A4829-8603 MANTLE

A4829-8671 CONCAVE

A4829-9481 CONCAVE

A4830-0023M BOWL LINER, MOD.

A4830-0023 CONCAVE

A4830-0158 CONCAVE

A4830-0350 CONCAVE

A4830-1101 CONCAVE

A4830-1151 CONCAVE

A4830-1288 CONCAVE

A4830-1371 4 'STD, CONCAVE(XC)

A4830-1826 CONCAVE

A4830-2957 CONCAVE

A4830-3531 BOWL LINER

A4830-3801 CONCAVE

A4830-4071 CONCAVE

A4830-4341 CONCAVE

A4830-4612 CONCAVE

A4830-4699 CONCAVE

A4830-4881 CONCAVE

A4830-4992 CONCAVE

A4830-5415 CONCAVE

A4830-6501 5 'CONCAVE

A4830-6771 5 'CONCAVE

Rev Date: 3-25-2015 .

Page 92: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

SYMONS CONE CRUSHER MANGANESE AND ASSOCIATED

PARTS

A4830-6772 BOWL LINER

A4830-6871 5 'CONCAVE

A4872-4795 SOCKET LINER

A5013-1001 MANTLE

A5013-1401 MANTLE

A5013-2201 MANTLE

A5013-2401 MANTLE

A5013-2501 MANTLE

A5013-3401 MANTLE

A5013-3601 MANTLE

A5013-3801 MANTLE

A5013-4101 MANTLE

A5013-4201 MANTLE

A5013-4451 MANTLE

A5013-4801 MANTLE

A5013-5401 MANTLE

A5013-5556 CONCAVE

A5013-5801 MANTLE

A5013-6001 MANTLE

A5013-7001 5' LOWER MANTLE

A5013-7401 LOWER MANTLE

A5013-9880 LOWER CONCAVE EXTENSION

A5013-9889 LOWER CONCAVE EXTENSION

A5013-9901 LOWER CONCAVE

A5014-0011 LOWER CONCAVE EXTENSION

A5014-0050 LOWER CONCAVE

A5168-5161 MAIN SHAFT NUT

A5168-5701 MAIN SHAFT NUT

A5598-2621 FEEDPLATE

A5598-3491 FEEDPLATE

A5598-4581 FEEDPLATE

A6273-2501 MAIN SHAFT SLEEVE

A6360-4161 SOCKET SEALING RING

A6380-5101 SOCKET SEALING RING

A6391-0181 TORCH RING

A6391-3321 TORCH RING

A7320-3201 MAIN SHAFT SLEEVE

A7320-4331 MAIN SHAFT SLEEVE

Rev Date: 3-25-2015 .

Page 93: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

METSO CONE CRUSHER MANGANESE AND ASSOCIATED

PARTS

PART NUMBER DESCRIPTION

A1957-8065 BOLT WEDGE HP300

A5520-8268S LINER BOWL MEDIUM HP300

A5520-8272SX21 LINER BOWL MEDIUM HP300

A5520-8281SX LINER BOWL MEDIUM HP300

A5530-8261S MANTLE FINE HP300

A5530-8262SX21 MANTLE FINE HP300

A5530-8267SX MANTLE FINE HP300

A6391-4652 WASHER MANTLE HP300

A6391-7418 ADAPTOR BOWL RING HP300

Rev Date: 11-03-2016 .

Page 94: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

00-320-001-3280 080015 SEAL CROWN PSP328

00-320-001-3360 080039 SEAL CROWN 2 7/8 X 3 1/4 X 3/

00-330-510-0118 079003 RING SNAP 5100-118

00-330-510-0375 079001 RING SNAP 5100-375

00-330-510-0450 079002 RING SNAP 5100-450

00-331-162-0000 070029 RING RETAINING WH162

00-420-000-0000 084002 O-RING 1/4

00-420-002-0120 080007 O-RING 2-012

00-420-002-1390 080017 O RING 2-139

00-420-002-1530 084004 O-RING PALL FILTER HOUSING

00-420-002-2220 084009 O-RING 6227-27

00-420-002-2230 084010 O-RING 6230-01

00-420-002-2250 084012 O-RING 6230-03

00-420-002-2260 084013 O-RING 6230-04

00-420-002-2340 084016 O-RING 6230-12

00-420-002-2380 084017 O-RING 6230-16

00-420-002-2680 084027 O-RING 6230-46

00-420-002-2700 084028 O-RING 9.0, 9-1/4, 1/8

00-420-002-2730 084030 O-RING 6230-51

00-420-002-2750 080004 O-RING 10 1/2 X 10 3/4 X 1/8

00-420-002-2790 084068 O-RING PARKER 2-279

00-420-002-3270 084001 O-RING 6227-30

00-420-002-3280 084034 O-RING 6227-31

00-420-002-3308 084036 O-RING

00-420-002-3370 084037 O-RING 6227-40

00-420-002-3450 084041 O-RING 6227-48

00-420-002-3540 084061 O-RING PARK 2-354, 5.125 ODX.1

00-420-002-4330 084050 O-RING 6227-60

00-420-002-4410 084052 O-RING 6227-68

00-420-002-4430 084053 O-RING 6227-70

00-420-002-4440 084054 O-RING 6227-71

00-420-002-4470 084055 O-RING 6227-74

00-420-002-4500 084056 O-RING 6227-77

00-420-002-4520 084057 O-RING 6227-79

00-420-002-4530 084058 O-RING 6227-80

00-420-002-4560 084059 O-RING 6227-83

00-420-002-4650 084060 O-RING 18 18-1/2 1/4

00-471-282-0600 060000 BUSHING QD SF 2-3/8

00-591-201-0000 090007 BRG PILLOW BLOCK VSC 1

00-70B-100-0000 076003 NUT COIL 1

00-710-048-0040 070019 HUCKBOLT FSTNR C50LR-BR24-8

00-710-048-0056 070020 HUCKBOLT FSTNR C50LR-BR24-12

00-710-048-0108 070021 HUCKBOLT FSTNR C50LR-BR24-16

00-710-048-0124 070022 HUCKBOLT FSTNR C50LR-BR24-20

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

Rev Date: 1-25-2012 .

Page 95: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

00-721-016-0032 070061 CAPSCREW HEX 1/4 20NC X 1/2

00-721-016-0048 070055 CAPSCREW HEX 1/4 20NC X 3/4

00-721-020-0048 070066 CAPSCREW HEX 5/16-18NC X3/4

00-721-020-0132 070068 CAPSCREW HEX 5/16-18NC X1-1/2

00-721-024-0048 070009 CAPSCREW HEX 3/8 16NC X 3/4 G5

00-721-024-0100 070008 CAPSCREW HEX 3/8 16NC X1G5

00-721-024-0116 070032 CAPSCREW HEX 3/8 16NC X 1-1/4

00-721-024-0132 070042 CAPSCREW HEX 3/8 16NC X 1-1/2

00-721-024-0148 070160 CAPSCREW HEX 3/8 16NC X 1-3/4

00-721-024-0200 070043 CAPSCREW HEX 3/8 16NC X 2 G5

00-721-028-0100 070072 CAPSCREW HEX 7/16 14NC X 1 G5

00-721-028-0116 070030 CAPSCREW HEX 7/16 14NC X1-1/4

00-721-028-0200 070074 CAPSCREW HEX 7/16 14NC X 2

00-721-028-0600 070028 CAPSCREW HEX 7/16 14NC X 6

00-721-032-0048 070007 CAPSCREW HEX 1/2 13NC X 3/4 G5

00-721-032-0100 070058 CAPSCREW HEX 1/2 13NC X 1 G5

00-721-032-0116 070027 CAPSCREW HEX 1/2 13NC X 1-1/4

00-721-032-0132 070016 CAPSCREW HEX 1/2 13NC X 1-1/2

00-721-032-0148 070059 CAPSCREW HEX 1/2 13NC X 1-3/4

00-721-032-0200 070048 CAPSCREW HEX 1/2 13NC X 2 G5

00-721-032-0216 070037 CAPSCREW HEX 1/2 13NC X 2-1/4

00-721-032-0232 070018 CAPSCREW HEX 1/2 13NC X 2-1/2

00-721-032-0248 070044 CAPSCREW HEX 1/2 13NC X 2-3/4

00-721-032-0300 070076 CAPSCREW HEX 1/2 13NC X 3 G5

00-721-032-0700 070196 CAPSCREW HEX 1/2 13NC X 7 G5

00-721-040-0100 070077 CAPSCREW HEX 5/8 11NC X 1 G5

00-721-040-0116 070015 CAPSCREW HEX 5/8 11NC X 1-1/4

00-721-040-0132 070184 CAPSCREW HEX 5/8 11NC X 1-1/2

00-721-040-0148 070010 CAPSCREW HEX 5/8 11NC X 1-3/4

00-721-040-0200 070038 CAPSCREW HEX 5/8 11NC X 2

00-721-040-0216 070158 CAPSCREW HEX 5/8 11NC X 2-1/4

00-721-040-0232 070014 CAPSCREW HEX 5/8 11NC X 2-1/2

00-721-040-0248 070167 CAPSCREW HEX 5/8 11NC X 2-3/4

00-721-040-0300 070079 CAPSCREW HEX 5/8 11NC X 3 G5

00-721-048-0132 070003 CAPSCREW HEX 3/4 10NC X 1-1/2

00-721-048-0148 070118 CAPSCREW HEX 3/4 10NC X 1-3/4

00-721-048-0200 070036 CAPSCREW HEX 3/4-10 X 2 G5 ZNC

00-721-048-0216 070023 CAPSCREW HEX 3/4 10NC X 2-1/4

00-721-048-0232 070045 CAPSCREW HEX 3/4 10NC X2-1/2 Z

00-721-048-0248 070024 CAPSCREW HEX 3/4 10NC X 2-3/4

00-721-048-0300 070000 CAPSCREW HEX 3/4 10NC X 3 G5

00-721-048-0316 070046 CAPSCREW HEX 3/4 10NC X 3-1/4

00-721-048-0332 070049 CAPSCREW HEX 3/4 10NC X 3-1/2

00-721-048-0500 070034 CAPSCREW HEX 3/4 10NC X 5

Rev Date: 1-25-2012 .

Page 96: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

00-721-048-0532 070104 CAPSCREW HEX 3/4 10NC X 5-1/2

00-721-056-0216 070182 CAPSCREW HEX 7/8 9NC X2-1/4G5Z

00-721-056-0232 070083 CAPSCREW HEX 7/8 9NC X 2-1/2

00-721-100-0216 070101 CAPSCREW HEX 1 8NC X 2-1/4

00-721-100-0300 070119 CAPSCREW HEX 1 8NC X 3 G5

00-721-100-0732 070195 CAPSCREW HEX 1 8NC X7-1/2G5

00-721-132-0700 070191 CAPSCREW HEX 1-1/2 6NC X 6 G5

00-722-048-0300 070115 CAPSCREW HEX 3/4 10NC X 3 G8

00-722-100-0216 070139 CAPSCREW HEX 1 8NC X 2-1/4 G8

00-722-100-0232 070161 CAPSCREW HEX 1 8NC X2-1/2G8

00-722-100-0248 070162 CAPSCREW HEX 1 8NC X 2-3/4G8

00-722-100-0332 070132 CAPSCREW HEX 1 8NC X3-1/2G8

00-722-100-0400 070169 CAPSCREW HEX 1 8NC X 4 G8

00-722-100-0432 070176 CAPSCREW HEX 1 8NC X 4-1/2G8

00-722-100-0500 070180 CAPSCREW HEX 1 8NC X 5 G8 ZIN

00-722-100-0700 070128 BOLT 1-8NC X 7.000 A490

00-723-040-0132 070004 BOLT CARRIAGE 5/8 11NC X1-1/2

00-726-020-0148 070140 CAPSCREW SOC 5/16 18NC X 1-3/4

00-726-024-0048 070039 CAPSCREW SOC 3/8 16NC X 3/4

00-726-032-0116 070457 CAPSCREW SOC 1/2 13NC X 1-1/4

00-726-040-0132 070057 CAPSCREW SOC 5/8 11NC X 1-1/2

00-726-048-0132 070179 CAPSCREW SOC 3/4-LONG X 1-1/2

00-726-048-0248 070198 CAPSCREW SOC 3/4 10NC X 2-3/4

00-726-056-0148 070189 CAPSCREW SOC 7/8 9NC X 1-3/4

00-728-016-0016 070126 SETSCREW SOC 1/4-20NC X 1/4

00-728-016-0032 070150 SETSCREW SOC 1/4 20NC X 1/2

00-728-016-0048 070040 SET SCREW SOC HD 1/4-20NC X3/4

00-728-016-0056 070626 SETSCREW SOC 1/4-20NC X 7/8

00-728-020-0024 070123 SETSCREW SOC 5/16-18NC X 3/8

00-728-020-0100 070088 SETSCREW 5/16 18NC X 1 G8

00-728-024-0024 070142 SETSCREW SOC 3/8 16NC X 3/8

00-728-024-0032 070122 SETSCREW SOC 3/8 16NC X 1/2

00-728-024-0048 070155 SETSCREW SOC 3/8 16NC X 3/4

00-728-032-0048 070151 SETSCREW SOC 1/2 13NC X 3/4

00-728-040-0040 070141 SETSCREW SOC 5/8 11NC X 5/8

00-72B-010-0048 070056 MACH SCREW RD HD #8-32NC X 3/4

00-72K-132-0248 070041 CAPSCREW SOC 1-1/2 6NC X2-3/4

00-72K-132-0400 070103 CAPSCREW SOC 1-1/2 6NC X 4

00-72M-010-0025 070173 CAPSCREW SOC M10-1.5 X 30MM 1

00-731-020-0048 070130 CAPSCREW HEX 5/16 24NF X 3/4

00-731-048-0132 070138 CAPSCREW HEX 3/4 16NF X 1-1/2

00-731-048-0200 070127 CAPSCREW HEX 3/4 16NF X 2 G5

00-731-048-0232 070025 CAPSCREW HEX 3/4 16NF X 2-1/2

00-731-048-0248 070026 CAPSCREW HEX 3/4 16NF X 2-3/4

Rev Date: 1-25-2012 .

Page 97: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

00-731-048-0500 070097 CAPSCREW HEX 3/4 16NFX 5 PLAIN

00-731-048-0532 070095 CAPSCREW HEX 3/4 16NF X 5-1/2

00-731-048-0600 070096 CAPSCREW HEX 3/4 16NF X 6 PLAI

00-731-048-0632 070124 CAPSCREW HEX 3/4 16NF X 6-1/2

00-731-048-0700 070006 CAPSCREW HEX 3/4 16NF X7G5 PL

00-731-100-0700 070170 CAPSCREW HEX 1 14NF X 7 G5

00-732-048-0400 070017 CAPSCREW HEX 3/4 16NF X 4 G8

00-734-000-0000 070152 CAPSCREW HEX 1 14NF X 3

00-738-016-0024 070011 SETSCREW SOC 1/4 28NF X 3/8

00-741-010-0000 076046 NUT #8-32NC

00-741-016-0000 076021 NUT 1/4-20NC

00-741-020-0000 076022 NUT 5/16 18NC

00-741-024-0000 076023 NUT 3/8-16NC

00-741-028-0000 076020 NUT 7/16-14NC

00-741-032-0000 076024 NUT 1/2-13NC

00-741-040-0000 076025 NUT 5/8-11NC

00-741-048-0000 076017 NUT 3/4-10NC G5

00-741-100-0000 076052 NUT 1-8NC G5 (PLAIN)

00-741-116-0000 076045 NUT 1-1/4 7NC

00-741-132-0000 076044 NUT HEAVY HEX 1-1/2-6NC

00-742-100-0000 076029 NUT JAM 1-8NC

00-742-116-0000 076053 NUT JAM 1-1/4-7NC

00-742-132-0000 076048 NUT JAM 1-1/2-6NC

00-745-040-0010 076010 NUT 5/8-11NC HVY ZINC

00-74C-016-0000 076026 NUT NYLOCK 1/4-20NC

00-74C-024-0000 076009 NUT NYLOCK 3/8-16NC

00-74C-028-0000 076028 NUT NYLOCK 7/16-14NC

00-74C-032-0000 076005 NUT NYLOCK 1/2 13NC

00-74C-040-0000 076001 NUT NYLOCK 5/8-11 NC

00-74C-048-0000 076000 NUT NYLOCK 3/4-10 NC G5

00-74C-100-0000 076059 NUT NYLOCK 1-8 NC

00-74C-116-0000 076054 NUT NYLOCK 1-1/4-7NC

00-74C-132-0000 076056 NUT NYLOCK 1-1/2-6 UNC

00-751-056-0000 076031 NUT 7/8-14NF

00-752-048-0000 076058 NUT JAM 3/4-10 NC

00-75A-048-0000 076006 NUT 3/4-16NF HIGH HEX G8

00-75A-100-0000 076002 NUT 1-8NC G5

00-75C-048-0000 076008 NUT NYLOCK 3/4-16NF G8

00-761-020-0000 078016 WASHER FLAT 5/16

00-761-024-0000 078017 WASHER FLAT 3/8

00-761-024-0010 078007 WASHER HT 3/8 YELLOW ZINC

00-761-028-0000 078018 WASHER FLAT 7/16

00-761-032-0000 078019 WASHER FLAT 1/2

00-761-032-0010 078004 WASHER HT 1/2 YELLOW ZINC

Rev Date: 1-25-2012 .

Page 98: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

00-761-040-0000 078020 WASHER FLAT 5/8

00-761-040-0010 078000 WASHER HT 5/8 YELLOW ZINC

00-761-048-0000 078021 WASHER FLAT 3/4

00-761-048-0010 078011 WASHER HT 3/4 YELLOW ZINC

00-761-056-0010 078029 WASHER HT 7/8 YELLOW ZINC

00-761-100-0000 078006 WASHER FLAT 1

00-761-100-0001 078038 WASHER TYP B 1.062ID X1.750 OD

00-761-100-0010 078030 WASHER HT 1 YELLOW ZINC

00-761-116-0000 078050 WASHER FLAT 1-1/4 USS ZN PL

00-761-132-0001 078036 WASHER FLAT 1-1/2

00-761-200-0000 078043 WASHER FLAT 2

00-762-010-0000 078037 WASHER LOCK #8

00-762-016-0000 078022 WASHER LOCK 1/4

00-762-020-0000 078023 WASHER LOCK 5/16

00-762-024-0000 078024 WASHER LOCK 3/8

00-762-028-0000 078001 WASHER LOCK 7/16

00-762-032-0000 078025 WASHER LOCK 1/2

00-762-040-0000 078014 WASHER LOCK 5/8

00-762-048-0000 078026 WASHER LOCK 3/4

00-762-056-0000 078034 WASHER LOCK 7/8

00-762-100-0000 078027 WASHER LOCK 1

00-763-024-0000 078002 WASHER COPPER 3/8

00-763-032-0000 078042 WASHER COPPER 1/2

00-76B-213-0000 078039 WASHER LOCK W-11

00-76B-227-0000 078031 WASHER LOCK W-12

00-76B-252-0000 078035 WASHER LOCK W-14

00-76B-313-0000 078013 WASHER LOCK W-16

00-76B-453-0000 078008 WASHER LOCK W-24

00-76B-514-0000 078009 WASHER LOCK W-26

00-76B-627-0000 078003 WASHER LOCK W-32

00-76B-739-0000 078041 WASHER LOCK W-38

00-79F-204-0000 076049 LOCKNUT N-11

00-79F-216-0000 076035 LOCKNUT AN-12

00-79F-240-0000 076039 LOCKNUT N-14

00-79F-300-0000 076018 LOCKNUT AN-16

00-79F-336-0000 076019 LOCKNUT AN-19

00-79F-436-0000 076013 LOCKNUT AN-24

00-79F-460-0000 076014 LOCKNUT AN-26

00-79F-520-0000 076015 LOCKNUT AN-28

00-79F-613-0000 076004 LOCKNUT AN-32

00-79F-725-0000 076055 LOCKNUT AN-38

00-801-048-3000 079000 DOWEL PIN .750 X 3.000

00-843-016-0000 070012 ZERK GREASE 1/4 28NF STR

00-847-032-0327 083031 5404-08-08

Rev Date: 1-25-2012 .

Page 99: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

00-847-048-0327 083030 5404-12-08

00-847-116-1300 083058 NIPPLE SCHD 40 1 1/4 X 13

00-848-032-0161 083037 5406-08-04

00-848-048-0247 083053 5406-12-06

00-848-100-0487 080014 OBSOLETE SEE 083028

00-848-116-0487 083052 5406-20-12

00-848-156-0481 083011 6405-24-12

00-84C-032-0323 080058 CONNECTOR 8-8 FBU-S

00-84D-032-0323 080018 CONNECTOR 8-8 FBU-S

00-84J-016-0003 083046 4 TU-S

00-84J-032-0003 080019 0319-08

00-84K-016-0003 083047 0318-04

00-84K-032-0003 083041 0318-08

00-84V-016-0003 083023 7129X4

00-863-032-0007 083061 5503-08-08

00-864-008-0164 083026 5502-04-02

00-864-016-0007 083010 5502-04-04

00-864-032-0004 083005 5502-08-08

00-864-048-0004 083024 5502-12-12

00-866-048-0324 083025 5502-12-08

00-86B-016-0083 083022 B7405X4

00-879-000-0010 083016 SAMPLER PLUG

00-879-032-0000 083007 5652-08-08-08-08

00-891-000-0100 083085 ADAPTOR, VALVE STEM

01-210-025-0125 020027 CONN 3/4" X 90 T&B 2272

01-222-041-6125 080055 SEAL OIL ROTATING

01-223-000-6125 080056 SLEEVE OIL SEAL HARDENED

01-224-005-0250 083039 NIPPLE QUICK DIS 3010-2 Parker

01-224-005-0260 083038 CPLR DISC QUICK PVV-14-F

01-224-100-0100 083051 TMP-14

01-225-002-0020 082004 HOSE SW 1/2X30-1/2 1/2MX1/2M

01-225-002-0040 082001 HOSE MC 1/4X17-5/8IN 04MBX04

01-225-002-0240 082003 HOSE SW 1/2X54 1/2MX1/2M

01-225-002-0510 082012 HOSE 1/4X 12IN - 04MB X 04MC

01-225-002-0610 082002 HOSE SW 3/4X50 3/4MX3/4M

01-225-002-3460 082005 HOSE SW 1/2X26 1/2MX1/2M

01-225-003-0010 090093 GUAGE 10000 PSI 1/4 NPT

01-540-008-0035 081002 TUBE SM 1/2 OD X .035 HYD

02-372-087-0000 086088 PUMP OIL (VSI) .11 CIR

02-372-715-0010 180002 EXIT PORTAL PROTECTOR 1800

02-382-021-0000 210002 BRG SPHERICAL

02-382-028-0010 210005 FLINGER SHAFT HOUSING VERTICAL

02-382-029-0000 210017 FLINGER LOWER 2100

02-382-033-0010 210012 SHAFT PINION 2100

Rev Date: 1-25-2012 .

Page 100: PDQ Replacement Parts Guide

PDQ REPLACEMENT PARTS

MISCELLANEOUS COMPONENTS

OEM PART NO. JCI PART NO. DESCRIPTION

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc.,

manufacturers of ELJAY and CEDARAPIDS® products. ELJAYTM

and CEDARAPIDS® are trademarks of Terex USA, LLC

02-382-051-0010 210018 NUT 2100 FLINGER

02-382-087-0010 086070 PUMP OIL VSI

02-450-052-0000 076016 NUT 2-1/4 4-1/2NC HOLD DN BT

02-450-053-0000 076040 NUT HEAVY HEX JAM 2-1/4 X 4-1/

02-450-472-0000 070105 CAPSCREW SOC 1-1/4 7NC X2-1/2

04-70-1130-0080 060158 SHEAVE IDLER 2 GR O S

04-70-1135-0313 070212 CAPSCREW HEX 1-1/2 6NC X 13 G5

Rev Date: 1-25-2012 .

Page 101: PDQ Replacement Parts Guide

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

26-101-053-031 AC-26-101-053-031 - Spacing Collar

36350 AC-36350 - O-Ring38150 AC-38150 - Seal

37250 AC-37250 - Bearing36300 AC-36300 - O-Ring

OEM P/N KPI OEM REP P/N

KPI RETRO P/N Description

PDQ REPLACEMENT PARTSALLIS CHALMERS®Simply reference the OEM PN and contact KPI for a quote.Use prefix "AC-" before the OEM P/N when placing an orderSCREEN PLANTS

Page 102: PDQ Replacement Parts Guide

OEM P/N KPI OEM REP P/N

KPI RETRO P/N Description

PDQ REPLACEMENT PARTSMCCLOSKEY®Simply reference the OEM PN and contact KPI for a quote.Use prefix "MCL-" before the OEM P/N when placing an orderR155 PORTABLE SCREEN PLANT

520-008-038 MCL-520-008-038 - Lord Mount520-008-050 MCL-520-008-050 - Wedge Assembly20.00.2156 MCL-20.00.2156 - Lamp Switch

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

32.15.1003 MCL-32.15.1003 - Hand Control Unit32.18.1066 MCL-32.18.1066 - Engine Speed Switch

Page 103: PDQ Replacement Parts Guide

JAW STYLE

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

400.0738.002 -

PDQ REPLACEMENT PARTSSANDVIK®Simply reference the OEM PN and contact KPI for a quote.Use prefix "SAN-" before the OEM P/N when placing an orderJaw Dies

400.0739.001 25-11-0024

400.0739.002

C

M

M

S

MODEL

25-11-0078400.2207.001

CJ211/J

M1107

-

400.1101.001 25-11-0075

400.1101.002 -

C

JAW STYLE

400.2207.002 -

FINTEC P/NSANDVIK P/N

400.1102.001

400.1102.002

-

-

400.0738.001 25-11-0057

C

C

C

C

M

S

S

ST

ST

ST

ST

S

S

S

MATERIALM1

M2

M1

M2

M1

M2

M1

M2

M1

M2

MOVING/STAT.M

KPI OEM REP P/NSAN-400.0738.001

SAN-400.0738.002

SAN-400.0739.001

SAN-400.0739.002

SAN-400.2207.002

SAN-400.1101.001

SAN-400.1101.002

SAN-400.1102.001

SAN-400.1102.002

SAN-400.2207.001

Page 104: PDQ Replacement Parts Guide

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

TV325.3A TRIO-TV325.3A - Carbide Insert

OEM P/N KPI OEM REP P/N

KPI RETRO P/N Description

PDQ REPLACEMENT PARTSTRIO®Simply reference the OEM PN and contact KPI for a quote.Use prefix "TRIO-" before the OEM P/N when placing an orderTV85 VSI

Page 105: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

X

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

X

X

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and

Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or Eagle Iron Works, manufacturer of EAGLE™ washing equipment.

ELJAY™ and CEDARAPIDS® are trademarks of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works.

Other names or designations for items of equipment described herein may be considered to be trademarks of the manufacturers of such products.

Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson Crushers International are affiliated with,

sponsored by or licensed by any such equipment manufacturer.

-

OEM P/N

SW5434411A

KPI RETRO P/N

-

TW5434411A -54" FMW Shaft, LH, less wear shoes

TRIO-SW5434411A

KPI OEM REP P/N

TRIO-TW5434411A

54" FMW Shaft, RH, less wear shoes

OEM P/N

114201013

Fine MW Coarse MW Log WKPI DROP-IN SHAFTS FOR WASH PLANTS

Description

Description

TRIO-114201013KP

KPI RETRO P/NFine MW Coarse MW

Spider, Only fits KPI Retro Shaft

Log WKPI OEM REP P/N

WASHING EQUIPMENT REPLACEMENT PARTS

PDQ REPLACEMENT PARTSTRIO®Simply reference the OEM PN and contact KPI for a quote.Use prefix "TRIO-" before the OEM P/N when placing an order

Page 106: PDQ Replacement Parts Guide

0330080012 CR0330080012 8 X 20

04248A28 CR-04248A28 4248 Tapered Bore Pitman Bearing Model04248A20A CR04248A20A 4248 1/2" Eccentric

0330070083 CR0330070083 7 X 20

0442804403 CR0442804403 2236 Post-1993442805601 CR442805601 2248 5/8" Eccentric442805602 CR442805602 2248 5/8" Eccentric

1/2" Eccentric

0442805701 CR0442805701 1242 1/2" Eccentric0442807301 CR0442807301 1248

01236WG01A CR01236WG01A 1236 1/2" Eccentric

PDQ REPLACEMENT PARTSCEDARAPIDS® JAW CRUSHER SHAFTSSimply reference the OEM PN and contact KPI for a quote.Use prefix "CR" before the OEM P/N when placing an orderJAW CRUSHERS

OEM P/N KPI OEM REP P/N

Jaw Size(s) Notes

0243600201 CR0243600201 2436 15/32" Eccentric

0304000207 CR0304000207 2743 5/8" Eccentric

00682SC01 CR00682SC01 1036 7/16" Eccentric, Long Ends

1/2" Eccentric

00682SE01 CR00682SE01 1036 7/16" Eccentric, Short Ends

0442804401 CR0442804401 2236 5/8" Eccentric

442806102 CR442806102 1636

442806001 CR442806001 1648 5/8" Eccentric442806002 CR442806002 1648 5/8" Eccentric

00881E CR00881E 2036 1/2" Eccentric

0442810002 CR0442810002 2436 15/32" Eccentric0094201 CR0094201 2540 5/8" Eccentric

0442810001 CR0442810001 3042 5/8" Eccentric0304200112 CR0304200112 3042 5/8" Eccentric

5/8" Eccentric442811401 CR442811401 3054 5/8" Eccentric

0094201 CR0094201 2540 1/2" Eccentric00942B CR00942B 2540 13/32" Eccentric

0305450008 CR0305450008 3054 5/8" Eccentric

0442811801 CR0442811801 5460 3/4" Eccentric, Replaces CR05460001540442807402 CR0442807402 4248 3/4" Eccentric, Replaces CR0424807401

SCREENS

OEM P/N KPI OEM REP P/N

Screen Size(s) Notes

0330060011 CR0330060011 6 X 20

0153605001NK CR0153605001NK 2236 Spacer

442811502 CR442811502 3660 5/8" Eccentric, Replaces CR0442811501

03242A0702 CR03242A0702 3242 13/32" Eccentric0442811601 CR0442811601 3648 5/8" Eccentric, Replaces CR0442807101

0442811601A CR0442811601A 3648 5/8" Eccentric

03242A0701 CR03242A0701 3242

Page 107: PDQ Replacement Parts Guide

OEM P/N KPI OEM REP P/N

Feeder Size(s) Notes

510015201044 CR510015201044 42" Flight520015201044 CR520015201044 42" Flight

CR09451206 60" DRIVE, ADJUST THROW, 1978 MODEL

APRON FEEDERS

H S I

OEM P/N KPI OEM REP P/N

Crusher Size(s) Notes

0404010049 CR0404010049 4040 Tension Rod

Technical Parts Manuals

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and

Johnson Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

09451205 CR09451205 60" DRIVER, ADJUST THROW, 1978 MODEL09451206

Page 108: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

XX

XX

XX

XX

XX

XX

XX

XX

XX

XXX

XXXX

X

A02734

A02882

A02883

A03393

A03394

A04135

A04136

A04636

A04671

A04685

A15254

A22242

A07844

A07846

A07847

A11548

A12088

A04691

A06534

A06535

A07842

A07843

A15236

A15237

A15253

RH Shoe (66" FMW)LH Shoe (66" FMW)RH Shoe (44" CMW)RH Shoe (INNER) (44"CMW)LH Shoe (44" CMW)LH Flight Shoe (INNER) (44" CMW)RH Shoe (72" FMW)

Right Hand Shoe (24" FMW)Left Hand Shoe (24" FMW)RH Paddle (44" CMW)LH Paddle (44" CMW)RH Shoe (24" CMW)RH Shoe (30" CMW)RH Shoe (36" CMW)LH Shoe (30" CMW)LH Shoe (36" CMW)

WASHING EQUIPMENT REPLACEMENT PARTS

PDQ REPLACEMENT PARTSEAGLE IRON WORKS®Simply reference the OEM PN and contact KPI for a quote.Use prefix "E-" before the OEM P/N when placing an orderAll wear shoes and tips come with the necessary hardware.

A02377

OEM P/NFine MW Coarse MW Log W

E-A02377

KPI OEM REP P/N

- Right Hand Shoe (36" FMW)E-A02734

E-A02882

E-A02883

E-A03393

E-A03394

-

-

-

-

-

E-A04135

E-A04136

E-A04636

E-A04671

E-A04685

-

-

-

-

-

E-A04691

E-A06534

E-A06535

E-A07842

E-A07843

-

-

-

-

-

E-A07844

E-A07846

E-A07847

E-A11548

E-A12088

-

-

-

-

-

E-A15236

E-A15237

E-A15253

E-A15254

E-A22242

-

-

-

-

-

KPI RETRO P/N Description

Left Hand Shoe (36" FMW)Right Hand Shoe (30" FMW)Left Hand Shoe (30" FMW)Paddle Blade (36" CMW)Paddle Blade (30" CMW)Right Hand Shoe (54" FMW)Left Hand Shoe (54" FMW)Right Hand Shoe (44" FMW) Left Hand Shoe (44" FMW)

Page 109: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

XX

XXX

XXXX

XX

XX

XXX

XX

XX

XX X

XX X X

X X X X XX X X X X X X X X XX X X X X

X X X X X XX X

X

A23750

E-A27073

E-A27077

E-A32894

E-A32895

E-A32896

KPI OEM REP P/N

Fine MW Coarse MW Log W

E-A23750

E-A27047

E-A27049

E-A27070

E-A27071

-

-

-

E-A32897

A27047

B02457

B03341

A27073

A27077

A32894

A32895

A32896

-

-

-

B05731

A32899

A27070

A27071

A27049

Stub Shaft w/Bolts

B05761

A32897

A32898

B06123

B06124

B06125

B03367

B03552

B05728

B05729

B05730

Stub Shaft w/BoltsB06126

E-B02457

E-B03341

-

-

-

B06129

B06137

Mounting Ring w/BoltsBearing Housing w/BoltsBearing Housing w/Bolts

E-B07332B07332

B06127

B06128

-

Stub Shaft w/BoltsStub Shaft w/Bolts

LH Shoe (36" FMW), U-ReinforcedLH Shoe (44" FMW), U-ReinforcedRH Shoe (44" FMW), ULH Shoe (44" FMW), URH Shoe (54" FMW), U

Spider w/Cap Screw W & Lockwire

LH Shoe (54" FMW), URH Shoe (36" FMW), ULH Shoe (36" FMW), UPaddle Blade (24" CMW)Paddle Tip w/Bolt (36" Log)Paddle Base w/Bolt (36" Log)Stub Shaft w/BoltsRH Flight Hub (30" CMW)RH Flight Hub (36" CMW)LH Flight Hub (30" CMW)LH Flight Hub (36" CMW)Paddle Blade (1 pc) w/Bolt (36" Log)

E-B03367

E-B03552

E-A32898

E-A32899

E-B05728

E-B05729

E-B05730

-

-

-

-

-

E-B05761

E-B06123

E-B06124

E-B06125

E-B06137

-

-

-

-

-

E-B06126

E-B06127

E-B06128

E-B06129

-

-

-

-

E-B05731

KPI RETRO P/N Description

WASHING EQUIPMENT REPLACEMENT PARTS (CONT.)

OEM P/N

-

- LH Shoe (72" FMW)- RH Shoe (44" FMW), U-Reinforced- RH Shoe (36" FMW), U-Reinforced- RH Shoe (54" FMW), U-Reinforced- LH Shoe (54" FMW), U-Reinforced

Driving Member

-

Page 110: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

XXXX

X X XX X XX X X

XXX

X X XX X X

X XX

X X XX XX X

XX X X X

XX

XX

XX

X

WASHING EQUIPMENT REPLACEMENT PARTS (CONT.)

OEM P/N KPI OEM REP P/N

Fine MW Coarse MW Log WKPI RETRO P/N

B18034

B18292

B18324

B18831

D01224

B10066

B17795

B17933

B18016

B18033

B09571

B09575

B09601

B10063

B10065

B08435

B08438

B08499

B08666

D01722

D02233

D02237

D04625

D04626

*Uses KPI rotated/spiral location pattern of Eagle Iron Works paddle mounts**Uses KPI shaft design (larger dia shaft) contact factory for details, ask about replacement spider requirements† KPI retro flights and spiders will only fit KPI retrofit shafts for OEM drop in shafts. Will not fit on OEM shafts.

LH Spiral Segment (44" FMW)RH Spiral Segment (36" FMW)

E-D01722

E-D02233

E-D02237

E-D04625

D05395

D05659

Sleeve Bearing

Description

Paddle Base w/Bolt (44" Log)Stub Shaft w/Bolts (44" Log)Bearing Housing w/Bolts (44" Log)Mounting Ring w/Bolts (44" Log)RH Paddle Hub (24" CMW)RH Paddle Hub (30" CMW) - Use B18292LH Paddle Hub (30" CMW) - Use B18394Spider w/Cap Screws & LockwireSpider w/Cap Screws & LockwireSpider w/Cap Screws & LockwireSpider w/Cap Screws & LockwireSpider w/Cap Screws & LockwireRH Paddle Hub (36" CMW)LH Paddle Hub (36" CMW)Paddle Tip (46" Log)

E-D04626

D04744

D05394

-

E-D04625KP†

E-D04626KP†

Paddle Support (36" Log), LHPaddle Support (36" Log), RHRH Spiral Segment (54" FMW)LH Spiral Segment (54" FMW)GasketRH Spiral Segment (44" FMW)

E-B08435

E-B08438

E-B08499

E-B08666

-

-

E-B09571

E-B09575

E-B09601

E-B10063

E-B10065

-

-

-

-

-

-

E-B17795KP†

E-B17933KP†

E-D04744

E-D05394

E-D05395

E-D05659

-

E-D05394KP†

E-D05395KP†

E-D05659KP†

-

-

E-B18034M

E-B18292

E-B18324

E-B18831

E-D01224

-

-

-

-

-

E-B10066

E-B17795

E-B17933

E-B18016

E-B18033

-

Gasket

- Paddle Tip w/Bolt (44" Log)- Paddle Support (44" Log), RH- Paddle Support (44" Log), LH

Page 111: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

XX

XX

X X X X X X X X X X XX X X X X X X X X X XX X X X X X X X X X XX X X X X X X X X X X

X X X X X X X X X X XX X X X X X X X X X X

XX

X X XX X X X XX X X X X

X X X X X XX X X X X X

X X XX X XX X XX X XX X XX X XX X XX X XX X X

XX

X X X X X X X X X X XX X X X X X X X X X X

OEM P/N KPI OEM REP P/N

D12925

D12926

D14384

D14392

D14393

D10706

D10771

D12782

D12896

D12899

D14451

D14445

D14446

D14447

D14448

D14450

E-D26461

E-D16575

Fine MW Coarse MW Log W

D09393

D09575

D09876

D06843

D08592

D08593

D09090

D09109

LH Spiral Segment (36" FMW)

WASHING EQUIPMENT REPLACEMENT PARTS (CONT.)

D16575

D16576

D26461

D05730

D09115

D09116

Paddle Spud (44" CMW)RH Flight Hub (24" CMW)

Flex Coupler Retaining Ring (44" Log)Flex Coupler Key (44" Log)

Bearing Sleeve Assembly- Bearing-

E-D09109

-

-

E-D05730 E-D05730KP†

E-D06843

E-D08592

E-D08593

E-D09090

E-D10706

E-D10771

E-D12782

206462

206463

-

-

-

E-D09115

E-D09116

E-D09393

E-D09575

E-D09876

E-D30877

206537

E-D12926

E-D14384

E-D14392

E-D16576

E-D14393

E-D14445

E-D14446

E-D14447

E-D14448

E-D14450

E-D14451

D30877

- Bearing (44" Log)

KPI RETRO P/N Description

- LH Flight Hub (24" CMW)- Gasket- Gasket- Clamp Plate w/Bolts- Bearing Seal- Seal- Gasket-

- Wear Sleave, SS

- Wear Sleave, SS (44" Log)-

Bearing Sleeve Assembly- Donut Seal (44" Log)- Slinger (44" Log)

Slinger

- Bearing Seal (44" Log)- Bearing

RH Spiral (44" CMW)- LH Spiral (44" CMW)- Donut Seal

Clamp Plate w/Bolts (44" Log)- Gasket (44" Log)- Gasket (44" Log)- Gasket (44" Log)

- Bearing Sleeve Assembly(44" Log)-

Page 112: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

X X XX X X X X X X X X X X X X X

X X X X X X X X X X X X X X

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

X XX X X X X

XX X

X X XX X

X X X X XX

X XX X X X X X X X X X X

D40580

D32750

D32751

D36122

Fine MW Coarse MW Log W

OUTBOARD BEARING ASSEMBLIES

A08285

E-D32750

E-D32751

E-D36122

E-D40580

E-A08285KP

-

-

WASHING EQUIPMENT REPLACEMENT PARTS (CONT.)

OEM P/N KPI OEM REP P/N

Fine MW Coarse MW Log W

E-D40600

Seal Kit-Sm

A08286RK

A08287RK

A08288RK

E-A08286RK

E-A08287RK

E-A08288RK

E-A08286

E-A08287

E-A08288

E-A13479

E-A08285RK

D40600

OEM P/N KPI OEM REP P/N

E-Seal Kit-Sm

A13479

A08285RK

A08286

E-A08285 Outboard Bearing AssemblyE-A08286KP Outboard Bearing Assembly

- Outboard Bearing Assembly- Outboard Bearing Assembly- Outboard Bearing Assembly- Outboard Bearing Assembly- Outboard Bearing Assembly

- Outboard Bearing Assembly

(8) Gasket (44" Log)- Gasket (14)- Wear Sleeve

A08287

A08288

- Outboard Bearing Assembly

Shaft Seal (16)- Shaft Seal (14)

KPI RETRO P/N Description

- Outboard Bearing Assembly

KPI RETRO P/N Description

Page 113: PDQ Replacement Parts Guide

24" 30" 36" 44" 48" 54" 66" 72" 24" 30" 36" 44" 36" 44" 46"

XX

XX

XX

XXXXXXX

XX

XXXX

XXXX

XXX

OEM P/N KPI OEM REP P/N

Fine MW Coarse MW Log WKPI DROP-IN SHAFTS FOR WASH PLANTS

KPI RETRO P/N Description

E-B06603*

B06617 E-B06617**

B06618 E-B06618**

B06602

B06626 E-B06626**

E-B06602*

54"x34' FMW Shaft, LH, less wear shoes

E-B06448KP 36"x25' FMW Shaft, RH, less wear shoes

- -

B13508 -

389274

389273 36"x30' Log Shaft, LH, less wear tips

E-B06617KP 44"x32' FMW Shaft, RH, less wear shoesE-B06618KP 44"x32' FMW Shaft, LH, less wear shoes

389272 36"x30' Log Shaft, RH, less wear tips

- -

- -

B06603

36"x25' FMW Shaft Assy, LH, Urethane Shoes-

E-B11253KP

E-B23534KP

E-B23535KP

B11256 E-B11256**

E-B11257KP

E-B11252KP

44"x32' FMW Shaft Assy, RH, Steel ShoesB11253

E-B11256KP 36"x25' FMW Shaft Assy, LH, Steel Shoes

B13533 -

E-B06625KP

36"x30' Log Shaft Assy, less rubber liners389297 36"x30' Log Shaft Assy, with rubber liners516144 36"x35 Twin Spiral Assy, less rubber liners

B06448 E-B06448**

B06449 E-B06449** E-B06449KP 36"x25' FMW Shaft, LH, less wear shoes

- - 516145 36"x35' Log Shaft, RH, less wear tips- - 516146 36"x35' Log Shaft, LH, less wear tips

B06625 E-B06625** E-B06625KP 54"x34' FMW Shaft, RH, less wear shoes

E-B23472KP

B23534

B23472

B11254 E-B11254** E-B11254KP 54"x34' FMW Shaft Assy, RH, Steel Shoes

- 54"x34' FMW Shaft Assy, RH, Urethane ShoesB11258 E-B11258** E-B11258KP 54"x34' FMW Shaft Assy, LH, Steel Shoes

44"x32' FMW Shaft Assy, LH, Steel Shoes

E-B23612KP 44"x32' FMW Shaft Assy, LH, Urethane Shoes

-

B11257 E-B11257**

B23612 -

B23611

E-B11253**

-

E-B13508KP* 44" Log Washer shaft, RH, less wear tipsE-B13533KP* 44" Log Washer shaft, LH, less wear tips

E-B23611KP 44"x32' FMW Shaft Assy, RH, Urethane Shoes

B11252 E-B11252** 36"x25' FMW Shaft Assy, RH, Steel Shoes

B23535

36"x25' FMW Shaft Assy, RH, Urethane Shoes

**Uses KPI shaft design (larger dia shaft) contact factory for details, ask about replacement spider requirements† KPI retro flights and spiders will only fit KPI retrofit shafts for OEM drop in shafts. Will not fit on OEM shafts.

*Uses KPI rotated/spiral location pattern of Eagle Iron Works paddle mounts

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or Eagle Iron Works, manufacturer of EAGLE™ washing equipment.eqELJAY™ and CEDARAPIDS® are trademarks of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works.

Other names or designations for items of equipment described herein may be considered to be trademarks of the manufacturers of such products.

Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson Crushers International are affiliated with,

sponsored by or licensed by any such equipment manufacturer.

Page 114: PDQ Replacement Parts Guide

E-D12265

D03613 E-D03613

D04159 E-D04159

B13821 E-B13821

D01645 E-D01645

D03447

D04182 E-D04182 - Bearing

218655 Yoke Pin Assembly

Paddle Rod Guard, 10' Wide Tanks- Paddle Rod, 10' Wide Tanks

-

D04186 -

D04185/297200015D04184 -

D04281 -

D12264 E-D12264 - 6" Power Op Valve Assy, 8' Wide Tanks

E-B08827KP Spout, RH, Urethane- E-B08828KP Spout, LH, Urethane- E-B08829KP Spout, Center, Urethane

- Valve Rod

- Valve Seal

-

Valve Seal Plate, 6"

- Paddle Rod Guard, 8' Wide Tanks- Relief Valve w/ Cartridge

Paddle Rod, 8' Wide Tanks

Motor

- Mercury Switch

- -

230637 Spring Pin

E-D03428

- Valve Guide, 8"- Valve Seat, 8"-

-

Hyd Cyl Assy, 1.5" Dia x 2.5" StrokeSwitch Plate

Stud

- 6" Power Op Valve Assy, 10' Wide TanksWedge

Gasket

Valve Seal Plate, 8"- Cylinder Rod End

Hyd Cyl Assy, 1.5" Dia x 2.5" Stroke

Description

Hyd Cyl Mount Plate-

KPI RETRO P/N

271768

-

-

-

-

-

-

218654 Adjustable Yoke End

D04181

D12265

-

B08237

B08402 E-B08402

B08403 E-B08403

B08404 E-B08404

B12828 E-B12828

B08240 E-B08240

B12836 E-B12836

B08827

B08828

B08829

-

B08241

B08335

B08401

Valve Seat, 6"Valve Seat Gasket, 6"Valve Guide, 6"

-

-

-E-B08241

-

E-B08401

Paddle- Valve Seal, 8"

E-B08237

E-D12268

D12269 E-D12269

D12551 E-D12551

D12593 E-D12593

D11401 E-D11401 - Valve Rod

D11200 E-D11200

D11201 E-D11201

D12172 E-D12172

D12268

- Tube- Paddle Rod

PDQ REPLACEMENT PARTSEAGLE IRON WORKS®Simply reference the OEM PN and contact KPI for a quote.Use prefix "E-" before the OEM P/N when placing an orderCLASSIFYING TANKS

B08026 E-B08026

OEM P/N KPI OEM REP P/N

E-D03447

D09266 E-D09266

D09267 E-D09267

D03426 E-D03426 - SpringD03428

Page 115: PDQ Replacement Parts Guide

D13240 - 345833 Downspout

D13244 - 345863 Downspout

D13237 278885 DownspoutD13238 - 276914 DownspoutD13239 - 276962 Downspout

D13241 - 255764 Downspout

D21985 E-D21985 - Manifold BlockE-D21986

E-D16658 - Coupling

- 255755 Downspout-

-

D16658

D21977 E-D21977

D12594 E-D12594

D13051 E-D13051

D18540

D20628

D22731 E-D22731

- Terminal Block End Barrier/Holder

-

D32298

D21986

D22008

D32214

E-D18540

D20627

Hyd. Male Connector

- Paddle Rod, 12' Wide Tanks- Paddle Rod Guard, 12' Wide Tanks

- Filter ElementE-D32214

Tube

- Tube-

E-D32298 -

D42000 E-D42000 - Gear Pump

Switch Arm

- Seal Kit

- Paddle Rod Guard

E-D20627

E-D20628

E-D22008M

Valve Rod

D13236

D13242 - 356931 DownspoutD13243 - 394001 Downspout

D13245 - 273893 DownspoutD13246 - 345841 DownspoutD13247 - 294009 Downspout

D13249 - 294015 DownspoutD13248 - 356935 Downspout

D13250 - 293583 DownspoutD13251 - 276976 Downspout

D21016 - 273770 Downspout

D15605 - 293658 Downspout

D15624 - 276910 Downspout

D19476 - 248864 Downspout

D21021 - 516735 Downspout

D15611 - 293660 Downspout

D21017 - 516726 DownspoutD21018 - 276964 Downspout

D20720 E-D20720 - 6" Power Op Valve Assy, 12' Wide TanksD20719 E-D20719 - 8" Power Op Valve Assy, 12' Wide Tanks

D21022 - 294008 DownspoutD21023 - 273775 Downspout

D20693 - 345853 Downspout

D21014 - 273863 Downspout

D21019 - 255704 DownspoutD21020 - 273900 Downspout

Page 116: PDQ Replacement Parts Guide

D42025 E-D42025

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

Technical Parts Manuals

- Holder

Page 117: PDQ Replacement Parts Guide

D42001 45-24051 Bolt

45-42002

D20303 45-60002 Flat Washer

D33978 33807 Bolt

D18553 505356 Adapter

D18706 Bolt

45-60038D18613 Lock WasherD18700 Bolt

OEM P/N Description

D00630 U-Bolt

D18525 Tee, Compression, Union

D00962 U-Bolt

D09071 BoltD04184 Pin

505357

Kolberg-Pioneer, Inc. and Johnson Crushers International (KPI-JCI) are not affiliated with, sponsored by or

licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™ and CEDARAPIDS® products, or

Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks

of Terex USA, LLC and/or Terex Corporation, and EAGLE™ is a trademark of Eagle Iron Works. Other names or

designations for items of equipment described herein may be considered to be trademarks of the manufacturers

of such products. Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc. and Johnson

Crushers International are affiliated with, sponsored by or licensed by any such equipment manufacturer.

MISCELLANEOUS

PDQ REPLACEMENT PARTSEAGLE IRON WORKS®Simply reference the OEM PN and contact KPI for a quote.Use prefix "E-" before the OEM P/N when placing an order

KPI REPLACEMENT P/N

E-D00630

E-D00962

230637

45-24090

45-00125

45-12057

45-00158

1785

D18717 BoltD18812 Hex Nut

D22834 Cotter Pin

D42504 505355 Elbow AdapterD42505 42-00282 Elbow Adapter

Page 118: PDQ Replacement Parts Guide

OEM P/N KPI OEM REP P/N

KPI RETRO P/N Description

PDQ REPLACEMENT PARTSEAGLE IRON WORKS®Simply reference the OEM PN and contact KPI for a quote.Use prefix "E-" before the OEM P/N when placing an orderPUGMILL

A24303 E-A24303 - Pugmill Paddle, LH, with Hardware

- Pugmill Paddle, RH, with Hardware- Pugmill Paddle, LH, with Hardware

A24302 E-A24302 - Pugmill Paddle, RH, with Hardware

A22941 E-A22941

A22942 E-A22942

Page 119: PDQ Replacement Parts Guide

Nothing in this advertisement should be taken as a claim that Kolberg-Pioneer, Inc., Johnson Crushers International, Inc. or Astec Mobile Screens (KPI-JCI-AMS) are affiliated with, sponsored by or licensed by Terex Corporation and Cedarapids, Inc., manufacturers of ELJAY™, CEDARAPIDS® and POWERSCREEN® products, or Eagle Iron Works, manufacturer of EAGLE™ washing equipment. ELJAY™ and CEDARAPIDS® are trademarks of Terex USA, LLC and/or Terex Corporation, POWERSCREEN® is a trademark of Terex GB, LLC of Northern Ireland and EAGLE™ is a trademark of Eagle Iron Works. Other names or designations for items of equipment described herein or offered for sale under our PDQ product line may be considered to be trademarks of the manufacturers of such products.

PriceDependabilityQuality

Contact your dealer to learn more.kpijci.com/dealer-locatorPhone: (800) 766-9793

Find the most recent PDQ parts guide at kpijci.com/parts/pdq-parts/