Embed Size (px)
Citation preview
Sealed RechargeableAGM Deep Cycle Battery
PDC SERIES
PDC-1235012 Volt 35.0 A.H. Power-Sonic Corporation
BAT
T ERY
MUSTB ERECYC
LED
PbNONSPILLABLE
www.power-sonic.com
MH20845
®
L
HTH
W
Tolerances are +/- 0.04 in. (+/- 1mm) and +/- 0.08 in. (+/- 2mm) for height dimensions. All data subject to change without notice.
Physical Dimensions: in (mm)
Features
Absorbent Glass Mat (AGM) technology for superior performance
Valve regulated, spill proof construction allows safe operation in any position
Oversize negative plates and a specialized paste formulation provide true deep cycle performance.
Special additives in the paste ensure superior performance in deep discharge situations.
Power/volume ratio yielding unrivaled energy density Rugged impact resistant ABS case and cover (UL94-HB) Approved for transport by air. D.O.T., I.A.T.A., F.A.A. and
C.A.B. certified U.L. recognized under file number MH 20845
•
•
•
•
•••
•
Performance SpecificationsNominal Voltage ........................................................................ 12 volts (6 cells)
Nominal Capacity
20-hr. (1.75A to 10.50 volts) .......................................................... 35.0 AH
10-hr. (3.30A to 10.50 volts) .......................................................... 33.0 AH
8-hr. (4.04A to 10.50 volts) .......................................................... 32.3 AH
5-hr. (5.79A to 10.20 volts) .......................................................... 28.9 AH
1-hr. (21.3A to 9.00 volts) ............................................................. 21.3 AH
15-min. (65.1A to 9.00 volts) .............................................................. 16.3 AH
Approximate Weight ........................................................... 25.0 lbs. (11.3 kg)
Energy Density (20-hr. rate) .................................. 1.56 W-h/in3 (95.13 W-h/l)
Specific Energy (20-hr. rate) ............................. 16.03 W-h/lb (35.35 W-h/kg)
Internal Resistance (approx.) ...................................................... 11 milliohms
Max Discharge Current (7 Min.) ............................................. 106.2 amperes
Max Short-Duration Discharge Current (10 Sec.) ................... 350 amperes
Shelf Life (% of nominal capacity at 68°F (20°C))
1 Month ...................................................................................................... 97%
3 Months ..................................................................................................... 91%
6 Months .................................................................................................... 83%
Operating Temperature Range
Charge .. ........................................................... -4°F (-20°C) to 122°F (50°C)
Discharge ....................................................... -40°F (-40°C) to 140°F (60°C)
Case ...................................................................................................... ABS Plastic
Power-Sonic Chargers ............................................................. PSC-124000A-C
PDC-12350
www.power-sonic.comTo ensure safe and efficient operation always refer to the latest edition of our Technical Manual, as published on our website.All data subject to change without notice.
Terminals (mm)
L: 7.68 (195) W: 5.12 (130) H: 6.46 (164) HT: 7.09 (180)
12 Volt 35.0 AH @ 20-hr. rate 33.0 AH @ 10-hr. rate
16.5
7
16 6
6
Torque: 3.9~5.4 Nxm
NB3: Heavy duty terminal posts with nut and bolt fasteners
•
ChargingCycle Applications: Limit initial current to 10.6A. Charge until battery voltage (under charge) reaches 14.4 to 14.7 volts at 68°F (20°C). Hold at 14.4 to 14.7 volts until current drops to under 358mA. Battery is fully charged under these conditions, and charger should be disconnected or switched to “float” voltage.
“Float” or “Stand-By” Service: Hold battery across constant voltage source of 13.5 to 13.8 volts continuously. When held at this voltage, the battery will seek its own current level and maintain itself in a fully charged condition.
Note: Due to the self-discharge characteristics of this type of battery, it is imperative that they be charged within 6 months of storage, otherwise permanent loss of capacity might occur as a result of sulfation.
ChargersPower-Sonic offers a wide range of chargers suitable for batteries up to 100AH. Please refer to the Charger Selection Guide in our specification sheets for “C-Series Switch Mode Chargers” and “Transformer Type A and F Series”. Please contact our Technical department for advice if you have difficulty in locating suitable models.
Discharge Characteristics
PDC-12350 12 Volt 35.0 AH @ 20-hr. rate, 33.0 AH @ 10-hr. rate®
Further InformationPlease refer to our website www.power-sonic.com for a complete range of useful downloads, such as product catalogs, material safety data sheets (MSDS), ISO certification, etc..
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20min h
4.0
4.5
5.0
5.5
6
6V Battery(V)
12V Battery(V)
.0
6.5
0 200 400 600 800 1000 1200 1400 1600 1800
20
40
60
80
100
120
0-20 -10 0 10 20 30 40 500
20
40
60
80100
120 0.05CA0.10 CA0.20CA
1CA0.5CA
2CA3CA
8 10 120
4 6
60
80
100
0 2
20
40
A
B
C
0 4 8 12 16 20 24 28
% (A) (V/cell)
Term
inal
Vol
tage
(V)
Cap
acity
Rat
io (%
)
Cap
acity
(%)
Rem
aini
ng C
apac
ity (%
)
Temperature(°C)
Temperature: 25°C ChargeVolume
ChargingCurrent
ChargedVoltage Charge at 0.1C Amp Initial Charging Current and
2.45V/Cell Constant Voltage at 25°C
Discharge TimeCharging Time (Hours)
Number of Cycles
Storage Time (Months)
A
B
C
10°C
100%DOD
50%DOD
30%DOD
30°C40°C
No supplementary charge required(Carry out supplementary charge before use if 100% capacity is required.)
Supplementary charge required before use.Optional charging way as below:1.Charged for above 3 days at limted current 0.25CA and constant volatge 2.25V/cell.2.Charged for above 20hours at limted current 0.25CA and constant volatge 2.45V/cell.3.Charged for 8~10hours at limted current 0.05CA .
Supplementary charge may often fail to recover the capacity.The battery should never be left standing till this is reached
25°C
Testing conditionDischarging:current 0.17C (FV 1.7V/cell);Charging:current 2.45V/cell,max. 0.25CA;Charging volume:125% of discharged capacity.
13.0
12.0 120
0.1C
0.08C
0.06C
0.04C
0.02C
2.5
2.4
2.3
2.2
2.1
0C
100
80
60
40
20
11.0
10.0
9.0
8.0
Charged Volume
Charge Voltage(Constant 2.45V/Cell)
After 50% DischargeAfter 100% Discharge
Charging Current(Initial at 0.1C Amp)
1.77A3.3A7.06A
12.05A21.3A36.3A85.8A125.4A
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20min h
4.0
4.5
5.0
5.5
6
6V Battery(V)
12V Battery(V)
.0
6.5
0 200 400 600 800 1000 1200 1400 1600 1800
20
40
60
80
100
120
0-20 -10 0 10 20 30 40 500
20
40
60
80100
120 0.05CA0.10 CA0.20CA
1CA0.5CA
2CA3CA
8 10 120
4 6
60
80
100
0 2
20
40
A
B
C
0 4 8 12 16 20 24 28
% (A) (V/cell)
Term
inal
Vol
tage
(V)
Cap
acity
Rat
io (%
)
Cap
acity
(%)
Rem
aini
ng C
apac
ity (%
)
Temperature(°C)
Temperature: 25°C ChargeVolume
ChargingCurrent
ChargedVoltage Charge at 0.1C Amp Initial Charging Current and
2.45V/Cell Constant Voltage at 25°C
Discharge TimeCharging Time (Hours)
Number of Cycles
Storage Time (Months)
A
B
C
10°C
100%DOD
50%DOD
30%DOD
30°C40°C
No supplementary charge required(Carry out supplementary charge before use if 100% capacity is required.)
Supplementary charge required before use.Optional charging way as below:1.Charged for above 3 days at limted current 0.25CA and constant volatge 2.25V/cell.2.Charged for above 20hours at limted current 0.25CA and constant volatge 2.45V/cell.3.Charged for 8~10hours at limted current 0.05CA .
Supplementary charge may often fail to recover the capacity.The battery should never be left standing till this is reached
25°C
Testing conditionDischarging:current 0.17C (FV 1.7V/cell);Charging:current 2.45V/cell,max. 0.25CA;Charging volume:125% of discharged capacity.
13.0
12.0 120
0.1C
0.08C
0.06C
0.04C
0.02C
2.5
2.4
2.3
2.2
2.1
0C
100
80
60
40
20
11.0
10.0
9.0
8.0
Charged Volume
Charge Voltage(Constant 2.45V/Cell)
After 50% DischargeAfter 100% Discharge
Charging Current(Initial at 0.1C Amp)
1.77A3.3A7.06A
12.05A21.3A36.3A85.8A125.4A
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20min h
4.0
4.5
5.0
5.5
6
6V Battery(V)
12V Battery(V)
.0
6.5
0 200 400 600 800 1000 1200 1400 1600 1800
20
40
60
80
100
120
0-20 -10 0 10 20 30 40 500
20
40
60
80100
120 0.05CA0.10 CA0.20CA
1CA0.5CA
2CA3CA
8 10 120
4 6
60
80
100
0 2
20
40
A
B
C
0 4 8 12 16 20 24 28
% (A) (V/cell)
Term
inal
Vol
tage
(V)
Cap
acity
Rat
io (%
)
Cap
acity
(%)
Rem
aini
ng C
apac
ity (%
)
Temperature(°C)
Temperature: 25°C ChargeVolume
ChargingCurrent
ChargedVoltage Charge at 0.1C Amp Initial Charging Current and
2.45V/Cell Constant Voltage at 25°C
Discharge TimeCharging Time (Hours)
Number of Cycles
Storage Time (Months)
A
B
C
10°C
100%DOD
50%DOD
30%DOD
30°C40°C
No supplementary charge required(Carry out supplementary charge before use if 100% capacity is required.)
Supplementary charge required before use.Optional charging way as below:1.Charged for above 3 days at limted current 0.25CA and constant volatge 2.25V/cell.2.Charged for above 20hours at limted current 0.25CA and constant volatge 2.45V/cell.3.Charged for 8~10hours at limted current 0.05CA .
Supplementary charge may often fail to recover the capacity.The battery should never be left standing till this is reached
25°C
Testing conditionDischarging:current 0.17C (FV 1.7V/cell);Charging:current 2.45V/cell,max. 0.25CA;Charging volume:125% of discharged capacity.
13.0
12.0 120
0.1C
0.08C
0.06C
0.04C
0.02C
2.5
2.4
2.3
2.2
2.1
0C
100
80
60
40
20
11.0
10.0
9.0
8.0
Charged Volume
Charge Voltage(Constant 2.45V/Cell)
After 50% DischargeAfter 100% Discharge
Charging Current(Initial at 0.1C Amp)
1.77A3.3A7.06A
12.05A21.3A36.3A85.8A125.4A
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20min h
4.0
4.5
5.0
5.5
6
6V Battery(V)
12V Battery(V)
.0
6.5
0 200 400 600 800 1000 1200 1400 1600 1800
20
40
60
80
100
120
0-20 -10 0 10 20 30 40 500
20
40
60
80100
120 0.05CA0.10 CA0.20CA
1CA0.5CA
2CA3CA
8 10 120
4 6
60
80
100
0 2
20
40
A
B
C
0 4 8 12 16 20 24 28
% (A) (V/cell)
Term
inal
Vol
tage
(V)
Cap
acity
Rat
io (%
)
Cap
acity
(%)
Rem
aini
ng C
apac
ity (%
)
Temperature(°C)
Temperature: 25°C ChargeVolume
ChargingCurrent
ChargedVoltage Charge at 0.1C Amp Initial Charging Current and
2.45V/Cell Constant Voltage at 25°C
Discharge TimeCharging Time (Hours)
Number of Cycles
Storage Time (Months)
A
B
C
10°C
100%DOD
50%DOD
30%DOD
30°C40°C
No supplementary charge required(Carry out supplementary charge before use if 100% capacity is required.)
Supplementary charge required before use.Optional charging way as below:1.Charged for above 3 days at limted current 0.25CA and constant volatge 2.25V/cell.2.Charged for above 20hours at limted current 0.25CA and constant volatge 2.45V/cell.3.Charged for 8~10hours at limted current 0.05CA .
Supplementary charge may often fail to recover the capacity.The battery should never be left standing till this is reached
25°C
Testing conditionDischarging:current 0.17C (FV 1.7V/cell);Charging:current 2.45V/cell,max. 0.25CA;Charging volume:125% of discharged capacity.
13.0
12.0 120
0.1C
0.08C
0.06C
0.04C
0.02C
2.5
2.4
2.3
2.2
2.1
0C
100
80
60
40
20
11.0
10.0
9.0
8.0
Charged Volume
Charge Voltage(Constant 2.45V/Cell)
After 50% DischargeAfter 100% Discharge
Charging Current(Initial at 0.1C Amp)
1.77A3.3A7.06A
12.05A21.3A36.3A85.8A125.4A
Cycle Life in Relation to Depth of Discharge
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20min h
4.0
4.5
5.0
5.5
6
6V Battery(V)
12V Battery(V)
.0
6.5
0 200 400 600 800 1000 1200 1400 1600 1800
20
40
60
80
100
120
0-20 -10 0 10 20 30 40 500
20
40
60
80100
120 0.05CA0.10 CA0.20CA
1CA0.5CA
2CA3CA
8 10 120
4 6
60
80
100
0 2
20
40
A
B
C
0 4 8 12 16 20 24 28
% (A) (V/cell)
Term
inal
Vol
tage
(V)
Cap
acity
Rat
io (%
)
Cap
acity
(%)
Rem
aini
ng C
apac
ity (%
)
Temperature(°C)
Temperature: 25°C ChargeVolume
ChargingCurrent
ChargedVoltage Charge at 0.1C Amp Initial Charging Current and
2.45V/Cell Constant Voltage at 25°C
Discharge TimeCharging Time (Hours)
Number of Cycles
Storage Time (Months)
A
B
C
10°C
100%DOD
50%DOD
30%DOD
30°C40°C
No supplementary charge required(Carry out supplementary charge before use if 100% capacity is required.)
Supplementary charge required before use.Optional charging way as below:1.Charged for above 3 days at limted current 0.25CA and constant volatge 2.25V/cell.2.Charged for above 20hours at limted current 0.25CA and constant volatge 2.45V/cell.3.Charged for 8~10hours at limted current 0.05CA .
Supplementary charge may often fail to recover the capacity.The battery should never be left standing till this is reached
25°C
Testing conditionDischarging:current 0.17C (FV 1.7V/cell);Charging:current 2.45V/cell,max. 0.25CA;Charging volume:125% of discharged capacity.
13.0
12.0 120
0.1C
0.08C
0.06C
0.04C
0.02C
2.5
2.4
2.3
2.2
2.1
0C
100
80
60
40
20
11.0
10.0
9.0
8.0
Charged Volume
Charge Voltage(Constant 2.45V/Cell)
After 50% DischargeAfter 100% Discharge
Charging Current(Initial at 0.1C Amp)
1.77A3.3A7.06A
12.05A21.3A36.3A85.8A125.4A
Charging Characteristics (Cycle Use)
Temperature Effects in Relation to Battery Capacity
Self Discharge Characteristics
CORPORATE OFFICE • 7550 Panasonic Way • San Diego, CA 92154 • USA • Tel: +1-619-661-2020 • Fax: +1-619-661-3650
CUSTOMER SERVICETel: +1-619-661-2030 Fax: [email protected]
INTERNATIONAL SALESTel: +1-650-364-5001 Fax: [email protected]
DOMESTIC SALESTel: +1-619-661-2020Fax: [email protected]
TECHNICAL SUPPORTTel: +1-619-661-2020 Fax: [email protected]
Contact Information www.power-sonic.com
1012 1M
© 2012. Power-Sonic Corporation. All rights reserved. All trademarks are the property of their respective owners.
![SAM3S8 / SAM3SD8 · 2019. 10. 13. · pioa / piob piodc[7:0] high speed mci datrg pdc pdc pdc pdc pdc pdc pdc pdc pdc pdc pdc pdc pdc dac0 dac1 timer counter 0 tc[0..2] ad[0..14]](https://img.dokumen.tips/doc/110x75/61180b84f50fc135d32d7973/sam3s8-sam3sd8-2019-10-13-pioa-piob-piodc70-high-speed-mci-datrg-pdc.jpg)
![arXiv:1710.06103v1 [quant-ph] 17 Oct 2017 PDC PBS FIG. 1. Setup to generate 1D TN states: The setup includes a PDC nonlinearity placed inside an optical loop. Laser pulses (red) from](https://img.dokumen.tips/doc/110x75/5b0d6fc87f8b9a02508db20c/arxiv171006103v1-quant-ph-17-oct-2017-pdc-pbs-fig-1-setup-to-generate-1d-tn.jpg)
![ARM-based Flash MCU - produktinfo.conrad.com · 128-Byte RX UART1 PDC Real-time Events PIO High Speed MCI DMA PDC PDC PDC PDC Timer Counter A TC[0..2] UART0 TWCK0 TWD0 TWD1 UTXD0](https://img.dokumen.tips/doc/110x75/5c387e4109d3f23f308b764d/arm-based-flash-mcu-128-byte-rx-uart1-pdc-real-time-events-pio-high-speed.jpg)
