Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
Metal Craft has manufactured dock systems for nearly 80 years! We are very proud of our history dating back to 1932 when two German fabricators started a small fabrication shop in Cleveland, Ohio. Since the beginning Metal Craft Docks has been considered one of the most well-built, durable boat piers on the market.
In the following pages, you will find the most common parts that occassionally require replacement throughout the lifetime of your dock system or lift. Our systems were engineered so well from the beginning that very few of our parts have changed; however, if you find a part on your dock or lift that you are unable to identify – Call us or take a picture of the part and email us at [email protected]. We’ll be more than happy to assist in selecting the correct replacement.
We encourage you to order through a local dealer whenever possible. The knowledge and experience our Dealers provide on their home lakes is invaluable – without them we would be unable to have such a large install base. Please utilize the part numbers included in this catalog when ordering from your local dealer.
We are always looking for ways to improve and share the Metal Craft experience! We welcome your comments, suggestions and even photos of your Metal Craft Dock system or Metal Craft Lift.
Phone: 1.800.989.DOCK 440.286.7135
Fax: 440.286.7134 [email protected] www.metalcraftdocks.com
I.
Contents
DOCK PARTS Stationary Dock Parts
Lightweight Floating Dock Parts
Heavy Duty Floating Dock Parts
Accessories
LIFT PARTS PWC Lift Parts
Boat Lifts
ORDER FORMS Dock Parts Order Form
Floating Dock Parts List
PWC/Boat Lift Parts Order Form
4-7
8-10
11-12
15
13-14
16-19
20
21
22
Stationary Dock Parts
Deck Ends are shipped pre-punched.
Order 5/16" Hardware separately.
3'W Item: 0080-01
4'W Item: 0080-02
5'W Item: 0080-03
6'W Item: 0080-04
Item: 0074-11 Lock Nut w/Nylon Insert
Item: 621X-00 Aluminum Pipe
Deck End
The standard base pad measures 12" x 12"
square and consists of a 1.60" drilled pipe
extension. Includes hardware.
5/16" Stainless Steel Lock Nut with teflon insert
used on all deck modules along with 5/16"
HHCS and flat washers.
Item: 6195-00 Stop Angle
Stop Angles are used when the side rail of one
dock section rests in the U-Hooks at the end of a
second section. See "T" and "L" layouts in the
Stationary Configuration Guide for example.
Includes hardware.
Item: 6220-00 12" Base Pads
Heavy Duty Schedule 10 Aluminum Pipe,
1-7/8" OD used as supports for all stationary
docks. 3.5'L Item: 6209-00
5'L Item: 6210-00
7'L Item: 6211-00
9'L Item: 6212-00
11'L Item: 6213-00
Item: 0080-XX
Deck Corners are 90 degree angles that secure
the side rail and the deck end on the deck
module.
Includes hardware.
Deck CornerItem: 0065-00
5/16" x 1" Stainless Steel Flat Washer. Used
with all 5/16" HHCS.
5/16" Flat WasherItem: 0074-10
5/16" x 1" HHCS in Stainless Steel are
standard hardware used on all deck modules.
Additional lengths are available - contact your
local Metal Craft Dealer for additional lengths.
O-Cap Item: 0010-01
Used on Stationary X-Braces and Corner Half
Braces to secure 1-7/8" pipe to the wishbone.
"T" Caps are stamped with a "T".
Includes hardware.
T-Cap (Standard)Item: 0011-01
The "O-Cap" for 1-7/8" pipe guides the pipe in
the Depth Brace. It is identified with a stamped
“O”. The "O-Cap" allows for the depth braces to
be adjusted without having to dive underwater.
Includes hardware.
5/16" x 1" HHCSItem: 0074-07
Call Toll Free: 1.800.989.3625 or [email protected] 4
Item: 6260-00 Left Corner Half Brace
Corner Half Braces include a swing arm and a
12"H Pipe Bracket. Corner Half Braces allow for
support pipe to be positioned at the end of the
dock (versus the X-Brace's side
position).Shipped with hardware. Does not
include the "T-Cap".
The non-standard base pad measures 18" x
18" square and consists of a 1.60" drilled pipe
extension. Best used in severe mud or boggy
bottoms. Note: The 18" Base Pads are extremely
difficult to remove from the lake bed. Includes
hardware.
Stationary U-Hooks are used to connect deck
modules. For end-to-end connection on 3'W &
4'W, use two (2) U-Hooks. For end-to-end
connection on 5'W & 6'W, use three (3) U-Hooks.
For connections along the 10'L side, use (4) U-
Hooks. Stationary U-Hooks are also used to
secure stationary deck modules to sea walls.
Includes hardware
Item: 628X-01 Long Depth Brace
Improve stability with Long Depth Braces where
there is 5'-7'of water depth below the X-Brace or
Corner Half Brace. Long Depth Braces are
typically used with 9'H pipe. Use (2) per X-Brace.
X-Brace and CHB not included. Includes
Hardware. PLEASE NOTE: Wehn ordering depth braces for CHB - the right depth brace is used on teh CHB-left; The left depth brace is used on the CHB-right. Med. Left Item: 6282-01 ea.
Med. Right Item: 6283-01 ea.
Item: 628X-01 Medium Depth BraceImprove stability with Medium Depth Braces
where there is 3'-5' of water depth below the X-
Brace or Corner Half Brace. Medium Depth
Braces are used with 7'H pipe. Use (2) per X-
Brace. X-Brace and CHB not included. Includes
Hardware. PLEASE NOTE: When ordering depth braces for CHB - the right depth brace is used on the CHB-left; the left depth brace is used on the CHB-right. Med. Left Item: 6280-01 ea.
Med. Right Item: 6281-01 ea.
Item: 6270-00 Stationary U-Hook
Item: 6261-00 Right Corner Half Brace
Corner Half Braces include a swing arm and a
12"H Pipe Bracket. Corner Half Braces allow for
support pipe to be positioned at the end of the
dock (versus the X-Brace's side position).Shipped
with hardware. Does not include the "T-Cap".
Item: 6265-XX Under Dock Support
Under Dock Leg Supports allow for pipes to be
located under the deck module. The Under Dock
Leg Support is trussed and telescoping w/2
gusset arms. Includes Hardware
3'W Item: 6265-01
4'W Item: 6265-02
5'W Item: 6265-03
6'W Item: 6265-04
All X-Braces are trussed with a 12"H Pipe
Bracket on either side of the brace for 1-7/8"
pipe. "T-Cap" is sold separately.
3'W Item: 6250-00
4'W Item: 6251-00
5'W Item: 6253-00
6'W Item: 6253-00
X-BraceItem: 625X-00
Used on support pipe measuring 1-7/8" OD.
Brown Caps are used on support pipes with
Earth Sand color deck modules
Used on support pipe measuring 1-7/8" OD.
White Caps are used on support pipes with
Cloud White and Sea Green deck modules.
White Pipe CapItem: 6230-03
Brown Pipe CapItem: 6230-01
18" Base PadsItem: 6222-00
Call Toll Free: 1.800.989.3625 or [email protected] 5
Side Braces for Medium Depth are used to
reduce movement parallel to the deck module.
Medium Depth Braces are a pre-requisite to
installing side braces. The end attachment is
supplied in two ways - "Extended O-Cap" and
"Punched". Use the Extended O-Cap version with
X-Bracing and the Punched version with Corner
Half Braces.
SB w/Ex. O-Cap Item: 6289-01
SB w/Punch Item: 6289-02
Kit includes (1) each Auger Bit, 9'H Pipe, and
Pipe Cap with all hardware. Does not include
Shoreline Clamps. Specify cap color when
placing orders.
9' w/ES Cap Item: 6299-01
9' w/CW Cap Item: 6929-03
Kit includes (1) each Auger Bit, 7'H Pipe, and
Pipe Cap with all hardware. Does not include
Shoreline Clamps. Specify cap color when
placing orders.
7' w/ES Cap Item: 6298-01
7' w/CW Cap Item: 6928-03
Item: 6294-XX Dbl. End Brace for CHB/Long Depth
Use Double End Braces in conjunction with the
Corner Half Brace and Long Depth Braces (7'-9'
depth) to reduce side-to-side movement in the
end of a deck module. Must be used in pairs. CHB
not included. Includes Hardware.
3'W Dbl. End Brace Long Item: 6293-01
4'W Dbl. End Brace Long Item: 6294-02
5'W Dbl. End Brace Long Item: 6293-03
6'W Dbl. End Brace Long Item: 6293-04
End Brace for CHB/Long DepthItem: 6292-XX
Item: 6293-XX
Use Classic End Braces in conjunction with the
Corner Half Brace and Medium Depth Braces (7'- 9'
depth to reduce movement perpendicular to the
deck module. The end brace attaches to the opposite side of the deck end across to the opooosite side at the bottom of the support pipe. Must be used in pairs. CHB not included. Includes
Hardware. 3'W End Brace Long Item: 6292-01
4'W End Brace Long Item: 6292-02
5'W End Brace Long Item: 6292-03
6'W End Brace Long Item: 6292-04
Item: 6303-XX 7' Auger Bit Kit
Use Double End Braces in conjunction with the
Corner Half Brace and Medium Depth Braces (5'-
7' depth) to reduce side-to-side movement in the
end of a deck module. Must be used in pairs. CHB
not included. Includes Hardware.
3'W Dbl. End Brace Med. Item: 6293-01
4'W Dbl. End Brace Med. Item: 6293-02
5'W Dbl. End Brace Med. Item: 6293-03
6'W Dbl. End Brace Med. Item: 6293-04
Dbl. End Brace for CHB/Med. Depth
Item: 6300-XX 11' Auger Bit, Pipe w/Cap Kit
Kit includes (1) each Auger Bit, 11'H Pipe, and
Pipe Cap with all hardware. Does not include
Shoreline Clamps. Specify cap color when placing
orders.
11' w/ES Cap Item: 6300-01
11' w/CW Cap Item: 6300-03
Kit includes (1) each Shoreline Clamp, Auger Bit,
7'H Pipe, and Pipe Cap with all hardware. Specify
cap color when placing orders.
7' Kit w/ES Cap: Item 6303-01
7' Kit w/WH Cap: Item 6303-03
Use Classic End Braces in conjunction with the
Corner Half Brace and Medium Depth Braces (5'-
7' depth to reduce movement perpendicular to
the deck module. Must be used in pairs. CHB
not included. Includes Hardware.
3'W End Brace Med. Item: 6291-01
4'W End Brace Med. Item: 6291-02
5'W End Brace Med. Item: 6291-03
6'W End Brace Med. Item: 6291-04
9' Auger Bit, Pipe w/Cap KitItem: 6299-XX
Item: 6298-XX 7' Auger Bit, Pipe w/Cap Kit
End Brace for CHB/Med. DepthItem: 6291-XX
Side Braces for Long Depth are used to reduce
movement parallel to the deck module. Long
Depth Braces are a pre-requisite to installing
Side Braces. The end attachment is supplied in
two ways - "Extended O-Cap" and "Punched".
Use the Extended O-Cap version with X-Bracing
and the Punched version with Corner Half
Braces.
SB w/Ex. O-Cap Item: 6290-01
SB w/Punch Item: 6290-02
Side Brace for Long DepthItem: 6290-XX
Side Brace for Medium DepthItem: 6289-XX
Call Toll Free: 1.800.989.3625 or [email protected] 6
Item: 6340-XX Stat. Shoreline Mounting Kit
The Stationary Shoreline Mounting Kit consists of
(2) 3.5'H pipe, (2) S.L. Clamps, (2) Pipe Caps and
hardware. The Shoreline Mounting Kit is used to
anchor the dock sections to the shore when a sea
wall is not present. Please specify cap color when
ordering.
Shoreline w/ES Cap Item: 6340-01
Shoreline w/WH Cap Item: 6340-03
Kit includes (1) each Shoreline Clamp, Auger Bit,
9'H Pipe, and Pipe Cap with all hardware.
Specify cap color when placing orders.
9' Kit w/ES Cap Item: 6304-01
9' Kit w/WH Cap Item: 6304-03
9' Auger Bit KitItem: 6304-XX
Kit includes (1) each Auger Bit, 9'H Pipe, and
Pipe Cap with all hardware. Does not include
Shoreline Clamps. Specify cap color when
placing orders.
9' w/ES Cap Item: 6299-01
9' w/CW Cap Item: 6929-03
Item: 6320-00 Shoreline Clamp
The Shoreline Clamp consists of the back piece,
the front piece that wraps the pipe and hardware.
The Shoreline Clamp enables the support pipe to
attach to the deck module. Shoreline Clamps are
used in the Auger Bit Kits and Shoreline Mounting
Kits. Pipe sold separately.
Splayed Legs widen the stance of the dock and
improve stability. Each leg increases the
effective width of the Base Pad by 1'. Must be
installed in pairs. Splayed Legs are primarily
used on 2'W docks manufactured in the 1960's
and 1970's. Includes hardware.
Splayed LegItem: 6310-00
Cast iron screw head that attaches to the
bottom of pipe allowing maximum anchoring to
the lake bed.
Item: 6307-00
Easily drive Auger Pipes into the lake bed with
the Auger Ratchet Wrench.
Auger Ratchet WrenchItem: 6306-00
Kit includes (1) each Shoreline Clamp, Auger Bit,
11'H Pipe, and Pipe Cap with all hardware.
Specify cap color when placing orders.
11' Kit w/ES Cap: Item 6305-01
11' Kit w/WH Cap: Item 6305-03
11' Auger Bit KitItem: 6305-XX
Cast Iron Auger Bit
Additional parts are available - please contact us for a replacement part if you do not find the item in our catalog. You can also email us a photo of the item to be replaced at [email protected] and we can assist you in identification.
Call Toll Free: 1.800.989.3625 or [email protected] 7
Galv. Steel Star Washer
The Galvanized Steel Star Washer is placed on
the "J" bolt so to "grip" the poly float securing the
float in place. One star washer is required per
"J" bolt for a total of 4 per float. Use in
conjunction with the lock nut, flat washers, and
"J" bolt.
Item: 0076-15 "J" Mounting Bolt
"J" Mounting Bolts are used to attach poly floats
to the underside of the deck modules on Light
Weight Floating docks. The "J" portion of the bolt
wraps around the underside piece of the side rail
so that the flat wahsers, star washers and lock
nuts can secure the poly float to the deck side
rail.
Item: 0093-XX Poly Floats
Poly Floats attach to the underside of Light
Weight Floating deck modules with "J" Bolts
and hardware not included. Additional sizes
are available - call us for details.
3'Wx4'Lx12"D Item: 0093-01
4'W x4'Lx12"D04 Item: 0093-025'Wx5'Lx12"D Item: 0093-036'Wx6'Lx12"D Item: 0093-04
Light Weight Floating Parts
Item: 6700-00 Hinge Connection (Complete)
The Heavy Duty Hinge Connection Complete
includes (2) male 10"L hinges, (2) female 10"L
hinges and (2) standard hinge pins. Heavy Duty
hinges connect two deck modules allowing
flexibility with water movement.
Item: 6701-00 Male Hinge
(1) 10"L Male hinge, heavy duty. Includes
attaching hardware. Does not include hinge pin
or other hinges.
Item: 6702-00 Female HingeItem: 0076-13
The 3/8" stainless steel lock nut is used along
with flat washers, star washer and "J" bolt. One
lock nut is required per "J" bolt for a total of 4
lock nuts per float.
(1) 10"L Female hinge, heavy duty. Includes
attaching hardware. Does not include hinge pin
or male hinge.
Item: 6703-00 T Hinge Connection (Complete)
Item: 0076-11
The Heavy Duty "T" Hinge Connection Complete
includes (2) "T" hinges, (2) male hinges, and (2)
standard hinge pins. "T" hinges are used to
connect LWF docks to a sea wall or to connect
floating docks in a perpindicular configuration
sucn as an "L" or "T" to allow for the deck modules
to move with water movement.
Item: 6704-00 T Hinge
(1) "T" Hinge, heavy duty. Includes attaching
hardware. Does not include hinge pins or male
hinge.
3/8" SS Lock Nut
3/8" Flat WasherItem: 0076-10
The 3/8" flat washer is used in conjunction with
locknuts, steel star washer and "J" mounting
bolts to attach poly floats to our deck modules.
Two washers are required per "J" mounting bolt
and 8 total washers are required per float.
Call Toll Free: 1.800.989.3625 or [email protected] 8
Item: 6705-00 Hinge Pin (Standard)
The Standard Hinge Pin includes (1) 2-3/4"
hinge pin with nylon bushing and stainless clip.
The hinge pin is used to secure "T"/Male hinges
and Female/Male hinges.
Item: 6706-00 Hinge Pin (Extended)
Includes (1) LWF Locking Plate, Right with
Gusset Arm and attaching hardware. Plate is
14"H.
Item: 6714-02 Finger Locking Plate Right
Item: 6714-01 Finger Locking Plate Left
Gussets strengthen finger docks off main
walkways with the addition of 45° angled braces.
Specify locked or hinged finger gusset when
ordering. Hinged gussets are shown in the photo to the left. For additional information, see the diagram on page 21. 2-Way Hinged Item: 6752-00
2-Way Locked Item: 6754-00
Item: 6714-00 Finger Locking Plate Complete
Locking Plate Conn. (Complete)Item: 6710-00
The Finger Locking Plate Complete Kit includes (2) standard 14"H locking plates, (1) 10"H left finger locking plate, (1) 10"H right finger locking plate and (4) gussett arms. Finger locking plates are used on Light Weight Floating Docks with a main walkway and finger docks connected off the walkway at a 90 degree angle. Includes hardware.
Item: 675X-00Locking Plate RightItem: 6712-00
Includes (1) LWF Locking Plate, Left with
Gusset Arm and attaching hardware. Plate is
14"H.
Locking Plate LeftItem: 6711-00
The LWF Locking Connection Complete includes
(2) left and (2) right locking plates in 14" height with Gusset Arms. Locking Plates are used to
create a rigid connection between two deck
modules allowing them to move up and down as
one piece with water level changes. Includes
hardware.
The 10"H right finger locking plate is used on the Light Weight Floating Docks where two sections have a locked connection at a 90 degree angle. The right finger locking plate is used in conjunction with a standard 14"H locking plate. Includes hardware and gusset (not pictured).
Gussets strengthen finger docks off main
walkways with the addition of 45° angled braces and pipe extension. Specify locked or hinged finger gusset and pipe length when ordering replacements. Two way hinged gussets are shown in the photo to the left; 1-way gusset would only have a gusset on the left or the right of the dock. For additional information, see the diagram on page 21. 1-Way Hinged Item: 6750-00
1-Way Locked Item: 6751-00
2-Way Corner Gusset
The Extended Hinge Pin includes (1) 3-1/4"
Hinge Pin with a castle nut & stainless still clip.
1-Way Corner GussetItem: 675X-00
Call Toll Free: 1.800.989.3625 or [email protected] 9
The 10"H left finger locking plate is used on the Light Weight Floating Docks where two sections have a locked connection at a 90 degree angle. The left finger locking plate is used in conjunction with a standard 14"H locking plate. Includes hardware and gussett (not pictured).
Steel Ring Collars
The Steel Ring Collar when used with pipe and
auger bit allows for the floating deck module to
adjust up and down with the fluctuation of water
levels. Available in 3" OD & 4" OD.
3" Item: 6760-00
4" Item: 6760-01
Item: 6765-XX Cable/Tow U-Bolt
9' Auger Bit Kit
Kit includes (1) each Shoreline Clamp, Auger Bit,
9'H Pipe, and Pipe Cap with all hardware. Specify
cap color when placing orders.
9' Kit w/ES Cap: Item 6304-01
9' Kit w/WH Cap: Item 6304-03
Kit includes (1) each Shoreline Clamp, Auger Bit,
11'H Pipe, and Pipe Cap with all hardware.
Specify cap color when placing orders.
11' Kit w/ES Cap: Item 6305-01
11' Kit w/WH Cap: Item 6305-03
11' Auger Bit KitItem: 6305-XX
The Cable/Tow U-Bolt allows for easing install or
removal of floating dock sections by attaching
rope to the U-Bolt. Cable/Tow U-Bolts can also
be used in place of Steel Ring Collars to tie off
platforms at a secure location on the shoreline.
Available in 1.13" and 2.5" lengths.
2.5" Length Item: 6765-00
1.13" Length Item: 6765-01
Gussets strengthen finger docks off main
walkways with the addition of 45° angled
braces. Specify locked or hinged finger
gusset when ordering. Hinged gussets are shown in the picture to the left. For additional information, see the diagram on page 21. 4-Way Hinged Item: 6753-00
4-Way Locked Item: 6755-00
4-Way Corner GussetItem: 675X-00
Kit includes (1) each Shoreline Clamp, Auger Bit,
7'H Pipe, and Pipe Cap with all hardware.
Specify cap color when placing orders.
7' Kit w/ES Cap Item: 6303-01
7' Kit w/WH Cap Item: 6303-03
7' Auger Bit KitItem: 6303-XX
The Shoreline Mounting Kit for Floating Docks
consist of (2) each 3.5'H pipe sections, male
hinges, female hinges, hinge pins, shoreline
clamps and pipe caps.
Shoreline w/ES Cap Item: 6770-01
Shoreline w/CW Cap Item: 6770-03
Shoreline Mounting KitItem: 6770-XX
Item: 6760-XX
Item: 6304-XX
Cast iron screw head that attaches to the bottom
of pipe allowing maximum anchoring to the lake
bed.
Cast Iron Auger Bit
Easily drive auger pipes into the lake bed with the
Auger Ratchet Wrench.
Auger Ratchet Wrench
Item: 6307-00
Item: 6306-00
Additional parts are available - please contact us for a replacement part if you do not find the item in our catalog. You can also email us a photo of the item to be replaced at [email protected] and we can assist you in identification.
Call Toll Free: 1.800.989.3625 or [email protected] 10
Item: 675X-00 1-Way Corner Gusset
Gussets strengthen finger docks off main
walkways with the addition of 45° angled braces.
Specify locked or hinged finger gusset when
ordering. For additional information, see the diagram on page 21. 1-Way Hinged Item: 6750-00
1-Way Locked Item: 6751-00
Item: 675X-00 2-Way Corner Gusset
Gussets strengthen finger docks off main
walkways with the addition of 45° angled braces.
Specify locked or hinged finger gusset when
ordering. Hinged gussets are shown in the photo to the left. For additional information, see the diagram on page 21. 2-Way Hinged Item: 6752-00
2-Way Locked Item: 6754-00
Item: 0093-XX Poly Floats Item: 6704-00 T Hinge
Poly Floats attach to the underside of the frame
on Heavy Duty Floating Docks. Additional depth
sizes are available - call us for details.
3'Wx4'Lx12"D Item: 0093-01
4'Wx4'Lx12"D Item: 0093-02
5'Wx5'Lx12"D Item: 0093-03
6'Wx6'Lx12"D Item: 0093-04
((1) "T" hinge, heavy duty. Includes attaching hardware. Does not inlcude hinge pins or male hinge.
Item: 6700-00 Hinge Connection (Complete) Item: 6705-00 Hinge Pin (Standard)
The Heavy Duty Hinge Connection Complete
includes (2) male 10"L hinges, (2) female 10"L
hinges and (2) standard hinge pins. Heavy Duty
hinges connect two deck modules allowing
flexibility with water movement.
The Standard Hinge Pin includes (1) 2-3/4" hinge
pin with nylon bushing and stainless clip.
Item: 6701-00 Male Hinge Item: 6706-00 Hinge Pin (Extended)
(1) 10"L Male hinge, heavy duty. Includes
attaching hardware. Does not include hinge pin
or other hinges.
The Extended Hinge Pin includes (1) 3-1/4" Hinge
Pin with a castle nut & stainless still clip.
The Heavy Duty "T" Hinge Connection Complete
includes (2) "T" hinges, (2) male hinges, and (2)
standard hinge pins. "T" hinges are used to
connect LWF docks to a sea wall or to connect
floating docks in a perpindicular configuration
sucn as an "L" or "T" to allow for the deck
modules to move with water movement.
Heavy Duty Floating Parts
Item: 6702-00 Female Hinge
(1) 10"L Female hinge, heavy duty. Includes
attaching hardware. Does not include hinge
pin or male hinge.
Item: 6703-00 T Hinge Connection (Complete)
Call Toll Free: 1.800.989.3625 or [email protected] 11
The Locking Plate 1-Piece Complete Connection
includes (2) single plates and hardware. Please
specify height when ordering.
6"H Item: 7013-01
8"H Item: 7013-02
12"H Item: 7013-03
The Locking Plate 1-Piece includes (1) single
plate and hardware. Please specify height when
ordering.
6"H Item: 7014-01
8"H Item: 7014-02
12"H Item: 7014-03
Locking Plate Female
Includes (1) Heavy Duty floating Female locking
plate and hardware. Please specify height when
ordering.
6"H Item: 7012-01
8"H Item: 7012-02
12"H Item: 7012-03
Locking Plate 1-Piece (Complete)
Item: 7011-XX Locking Plate Male
The Shoreline Mounting Kit for Floating Docks
consist of (2) each 3.5'H pipe sections, male
hinges, female hinges, hinge pins, shoreline
clamps and pipe caps. Please specify pipe cap
color when ordering.
Shoreline w/ES Cap Item: 6770-01
Shoreline w/CW Cap Item: 6770-03
Item: 7010-XX Locking Connection (Complete)
The Heavy Duty Floating Locking Connection
Complete includes (2) each male and female
locking plates in 8" or 12" height. Locking Plates
are used to lock dock sections together. Includes
hardware. Please specify height when ordering.
6"H Item: 7010-01
8"H Item: 7010-02
12"H Item: 7010-03
Item: 7012-XX
Item: 7013-XX
Item: 7014-XX
Includes (1) Heavy Duty floating Male locking
plate and hardware. Please specify height when
ordering.
6"H Item: 7011-01
8"H Item: 7011-02
12"H Item: 7011-03
Item: 675X-00 4-Way Corner Gusset
Gussets strengthen finger docks off main
walkways with the addition of 45° angled
braces. Specify locked or hinged finger
gusset when ordering. Hinged gussets are shown in the picture to the left. For additional information, see the diagram on page 21.4-Way Hinged Item: 6753-00
4-Way Locked Item: 6755-00
Item: 6760-XX Steel Ring Collars
The Steel Ring Collar when used with pipe and
auger bit allows for the floating deck module to
adjust up and down with the fluctuation of
water levels. Available in 3" OD & 4" OD.
3" Item: 6760-00
4" Item: 6760-01
Item: 6770-XX Shoreline Mounting Kit
Additional parts are available - Often times Heavy Duty Floating Systems are comprised of custom pieces made specifically to meet the conditions at the installation site. These items can still be, in most cases,manufactured. Please contact us if you do not see the item needed in our catalog.
Call Toll Free: 1.800.989.3625 or [email protected] 12
Style 1 measures 3"H x 1-1/4" deep and is
available in 10' lengths. Style 1 covers most of
the top and side of 2' x 4" bumper board
material. Lumber not included; Bumper
Brackets sold separately.
Secure boats to a Metal Craft Dock without
drilling holes into the deck slats. Unique custom
aluminum design mounts strongly to deck and
can be easily relocated. Includes mounting
hardware.
Item: 6010-00 Swim & Safety Ladder
60"H with 4 steps 12" apart. A 2'W x 16"L 3M®
Safety-Walk Tread Strip is applied to the steps to
ensure good footing. Ladder is installed on
either a Metal Craft Dock or on a wood pier.
Includes mounting hardware.
Item: 6020-XX 3 Person Bench
62" L x 34" H x19" D. Designed to comfortably
seat 3 adults. Available in Earth Sand, Cloud
White, or Sea Green seat & back color to
coordinate with deck module. Includes
mounting hardware.
Earth Sand Item: 6020-01
Sea Green Item: 6020-02
Cloud White Item: 6020-03
Item: 6030-00 8" Mooring Cleat
Item: 6039-00 Style 1 PVC Bumper Material Item: 6040-00
Accessories
Style 2 PVC Bumper Material
Style 2 measures 3-1/2"H x 1-1/4" deep and is
available in 10' lengths. Style 2 fully covers side
of 2" x 4" or 4" x 4" wood post. Lumber not
included; Bumper Brackets sold separately.
Item: 6061-01 6" Solar Cleat Lite
The 6" Solar Cleat Lite is a great way to illuminate
your dock while providing mooring at the same
time. Two super bright LED lights and powerful
solar panel provide all night illumination. The 6"
Solar Cleat Lite can be installed on MCD deck
modules as well as wood docks. Please specify if
you are installing on a Metal Craft Dock when
ordering.
Item: 0224-00
The Swim Ladder Parts Kit includes (2) each swim
ladder clamps, swim ladder mounting angle, deck
clips, deck support bracket and (4) 5/16" x 1"
HHCS.
Swim Ladder Parts KitItem: 0225-00
The Bench Parts Kit includes the necessary
hardware to mount bench to Metal Craft Docks.
Kit includes (2) under dock braces (angle), (4) 1-
3/4" x 1/4" SSHH Bolts, (8) 1/4" SS Flat
Washers, (4) 1/4" SS HH Lock Nut.
Bench Parts Kit
Item: 6060-01-X Solar Dock LiteLight up each section of your stationary dock
with solar powered dock lights. The Solar Dock
Lite fits Metal Craft's standard 1-7/8" post.
Additional light bulb colors are available.
Packaged in sets of 2 and includes LED's,
batteries, and pipe adapters. Buy more, save
more available for this item.
White Lite:6060-01-W Blue Lite: 6060-01-B
Green Lite: 6060-01-G Red Lite: 6060-01-R
Yellow Lite: 6060-01-Y Orange: 6060-01-O
Item: 6060-02 Solar Deck Lite
Illuminate your path with low profile design, solar
powered deck lights mounted directly to your
MCD deck module or to a wood dock. The Solar
Deck Lite is made from anodized aluminum and
includes rechargeable batteries and white LEDs.
Please specify if you are installing on a Metal
Craft Dock when ordering. Buy more, save more
available for this item.
Call Toll Free: 1.800.989.3625 or [email protected] 13
Item: 6361-00 Horiz. Bumper Bracket - End
For Stationary Docks
Aluminum brackets mount to the end of dock to
attach a 2" x 4" bumper board horizontally to the
deck modules. Includes hardware. Bumper
board material not included; PVC bumper
material sold separately.
For Stationary Docks
Aluminum brackets mount on side of dock to
attach 2" x 4" bumper board horizontally to the
deck modules. Includes hardware. Bumper
board material not included; PVC bumper
material sold separately.
Item: 6360-XX Vertical Bumper Bracket
Item: 6350-00
For Heavy Duty Floating Docks
The Horizontal Bumper Bracket for floating docks
can be installed on the side of the Heavy Duty
frame section. Lumber not included; PVC bumper sold separately.
Item: 7090-XX Vertical Bumper Bracket
For Heavy Duty Floating Docks
Aluminum brackets mount on the side of the
dock and attach a 4" x 4" upright post. Wood
post not included, PVC bumper material sold
separately. Specify size when ordering. For use
with 4"x4" wood post, order item 7090-00. For
use with 4"x4" wood post with white post
sleeve, order item 7090-02.
For Floating Docks
The Horizontal Bumper Bracket for floating docks
can be installed on the either Lightweight
Floating or Heavy Duty Floating docks. See
specifications below for placement. Lumber not included; PVC bumper sold seperately.LWF - HBB can be installed on the side or the end of the deck module.HDF - This HBB can be installed on the end of the heavy duty frame section. For side installation, we recommend using item 7080-00 for best results.
For Light Weight Floating Docks
The Vertical Bumper Bracket - single option
includes one bracket and a cross deck brace for
reinforcement in the deck module. Wood post not
included, PVC bumper material sold separately.
Specify size when ordering. For use with 4"x4"
wood post, order item 6390-00. For use with
4"x4" wood post with white post sleeve, order
item 6390-02.
For Light Weight Floating Docks
The Vertical Bumper Bracket - pair option
includes two brackets and a cross deck brace
(not pictured) for reinforcement in the deck
module. Wood post not included, PVC bumper
material sold separately. For use with 4"x4" wood post, order item 6391-00. For use with 4"x4" wood post with white post sleeve, order item 6391-02.
For Stationary Docks
Aluminum brackets mount on the side of the
dock and attach a 4" x 4" upright post. Includes
hardware. Please specify model below. Wood
post and white sleeve not included, Vinyl PVC
sold separately.
For use with 4"x4" wood post, order item 6360-
00. For use with 4"x4" wood post with white
post sleeve, order item 6360-02.
Item: 6391-XX Vert. Bumper Bracket (Pair)
Vert. Bumper Bracket (Single)Item: 6390-XX
Item: 6380-01 Horizontal Bumper Bracket
Item: 7080-00 Horizontal Bumper Bracket
Bumper Brackets
Horiz. Bumper Bracket - Side
Call Toll Free: 1.800.989.3625 or [email protected] 14
Item: 1000-01 Gray Spinner Knob Kit
The Spinner Knob Kit includes (1) spinner know,
(1) 3/8"x3" HHCS ZY, (1) 3/8" Nylon Insert Lock
Nut ZY, (1) 3/8" Finished Hex Nut ZY, and (3)
3/8" USS Flat washer ZY.
Item: 375X-03
Item: 1225-01-SS 1200 PWC Winch Cable
PWC Winch Kit includes hardware. Manufactured
by Dutton-Lainson for Metal Craft PWC Lifts.
Specify model needed when ordering.
850 PWC Item: 3755-03
1200 PWC Item: 3756-03
The 1200 PWC Winch Cable measures 1/4" x
15'L Stainless Steel.
PWC Winch Kit
2" Pulley with Stainless steel shaft for model
850 & 1200 PWC Lifts. This pulley includes
chain link. Two (2) pulleys are required per
lift.
26" Winch Operating Wheel, steel with black, 2
spoke - shipped boxed with hardware.
Replacement works with both 850 & 1200 model
PWC Lifts.
Item: 1005-02 2" Pulley w/Chain Link Item: 3760-03 26" Winch Operating Wheel
Item: 1005-01 2" Pulley w/o Chain Link
2" Pulley with Stainless Steel Shaft for model
850 & 1200 PWC Lifts. This pulley does not
have chain link. One (1) pulley is required per
lift.
The 3-Piece Pulley Replacement Kit includes (2)
of Pulley item 1005-02 and (1) of Pulley item
1005-01. Replacement kit works for both 850
& 1200 model PWC lifts.
Item: 1125-01-SS 850 PWC Winch Cable Item: 1006-01 Pulley Replacement Kit
PWC Lift Parts
The 850 PWC Winch Cable measures 3/16"
x 13'L stainless steel.
Call Toll Free: 1.800.989.3625 or [email protected] 15
The Winch Cable is used on both model 4000-
110 and 4000-122 Boat Lifts. It measures
5/16"x26'L, Stainless Steel.
Item: 1610-03
The Pontoon Bunk Mounting Bracket is made of
steel with a galvanized finish. A special 3M
Scotchrap Corrosion-Protection Tape has been
applied to the bottom surface of the bracket to
provide all-weather corrosion protection between
the bracket and the aluminum cradle member.
DO NOT REMOVE OR CUT THIS TAPE. Four (4)
brackets are required per lift. Does not include
hardware.
There are (2) Rear Cradle Cables per lift. Cable
measures 5/16" x 191"L, Stainless Steel.
Item: 1538-03 Side Guide Post
The Side Guide Post attaches to carpeted
lumber and helps to guide boats onto the lift.
Each carpeted bunk requires (2) posts for a
total of (4) per lift. Mounting hardware and side
guide support base sold separately. Side guide
posts are used on Deluxe Side Guides, Pontoon
Side Guides and Utility Side Guides. Shown with carpeted bunks and lag screw not included.
Item: 1539-01 Side Guide Support Base
The Side Guide Support Base is used in
conjunction with the side guide post for
Pontoon Side Guides, Deluxe Side Guides and Utility Side Guides. The Side Guide Support
Base attaches to the lift cradle with the use of
U-Bolts. Mounting Hardware and Side Guide
Posts are sold separately.
4000-122 Rear Cradle Cable
There are (2) Rear Cradle Cables per lift. Cable
measures 5/16" x 202.5"L, Stainless Steel.
Item: 1610-04SS 4000 Winch Cable
4000-110 Rear Cradle Cable
Item: 1000-01 Gray Spinner Knob Item: 1539-02 U-Bolt Bottom Plate
Replacement knob - threaded
The U-Bolt Bottom Plate is used in conjunction
with the U-Bolt. U-Bolt and Locknut sold
separately. Use one (1) plate per U-Bolt.
Item: 1500-02 Extended Lift Leg Item: 1610-01 4000 Side Cradle Cable
The Extended Lift Leg measures 8'L and can be
used in place of the standard 54"L leg in deeper
waters. Leg pad measures 10" x 18" square.
There are (2) Side Cradle Cables per lift. Cable
measures 5/16" x 182"L, Stainless Steel. This
cable is used on both model 4000-110 and 4000-
122 Metal Craft Boat Lifts.
Item: 1537-01 Pontoon Bunk Mntg. Bracket Item: 1610-02
Boat Lift Parts
Call Toll Free: 1.800.989.3625 or [email protected] 16
Item: 3703-01 Clevis Pin
Used to fasten the foot/leg pad to the side/post
assembly. Use with hair pin cotter pin sold
separately. See assembly guides for more
information.
Item: 3703-02 Hair Pin Cotter Pin
Used in conjunction with the Clevis Pin to secure
the Foot/Leg Pad to the Side/Post Assembly on
the 4000 & 5000 model lifts. See assembly
guides for more information.
Item: 3700-02 HH Lag Screw 3/8" x 1-1/4"
The Winch Cable is used on both model 5000-
115 and 5000-122 Boat Lifts. It measures
3/8"x27'L, stainless steel.
There are (2) Side Cradle Cables per lift. Cable
measures 3/8" x 194.5"L, Stainless Steel. This
cable is used on both model 5000-115 and
5000-122 Metal Craft Boat Lifts.
Item: 1710-02 5000-115 Rear Cradle Cable
There are (2) Rear Cradle Cables per lift. Cable
measures 3/8" x 197"L, Stainless Steel.
Item: 1725-01 5000 Lorenz Winch
Item: 1710-01 5000 Side Cradle Cable
Item: 1625-01
Item: 1710-04SS 5000 Winch Cable
There are (2) Rear Cradle Cables per lift. Cable
measures 3/8" x 203.5"L, Stainless Steel.
The 3/8" x 1-1/4" Hex Head Lag Screw is made
of Zinc. Review assembly guides to determine
number of bolts required. Hex Head Lag screws are used in conjunction with the
following components: Pontoon Side Guide
Posts, Pontoon Bunks, Deluxe Side Guide
Posts and Deluxe Bunks.
Item: 3700-11 Lock Nut 3/8"
The 3/8" Locknut in Zinc with a Nylon Insert.
Lock nuts are used in conjunction with U-Bolts
and the U-Bolt Bottom plate, each sold
separately.
Item: 1710-03 5000-122 Rear Cradle Cable
4000 Lorenz Winch
The 4000 Winch is manufactured by Lorenz for
Metal Craft Lifts and includes a post mounting
bracket. The Winch is used on both model 4000-
110 and 4000-122.
The 5000 Winch is manufactured by Lorenz for
Metal Craft Lifts and includes a post mounting
bracket. The Winch is used on both model 5000-
115 and 5000-122.
Call Toll Free: 1.800.989.3625 or [email protected] 17
Item: 3752-01 Brake Winch Parts Kit
The Brake Winch Parts Kit is for both
4000/5000 model lifts. The parts kit includes
(1) allen wrench, 1 bolt, 1 locking washer, 1 large washer and instructions.
The Round U-Bolt measures 1/2"x4-3/4"Lx1-
1/4"IDx1-1/2"T and is made of Zinc Yellow. The
Round U-Bolt is used to attach the Upward Cables
to the lift frame. See Assembly Guides for more
information. Washers and locknuts sold
separately.
The 1/2" Square Nut (3/4"x3/4") in Stainless
Steel is used on the Side Guide Support Bases.
(4) required per Side Guide Support Base - See
Assembly Guides for more information.
Item: 3706-13 HHCS 1/2" x 1-3/4", SS
The 1/2"x1-3/4" Hex Head Cap Screw in
Stainless Steel is used on the Side Guide
Support Bases. (4) required per Side Guide
Support Base - See Assembly Guide for more
information.
Item: 3706-08 1/2" Lock Nut Item: 3709-06 Square U-Bolt
The Stainless Steel Bolt Kit for Nylatron Pulleys
includes (1) Stainless Steel Bolt 5/8"D with one
Lube Fitting. Used on both model 4000 & 5000
Lifts.
Item: 3706-12 1/2" Square Nut, SS
Stainless Steel Bolt Kit
The 1/2" Lock Nut with Nylon Insert is used in
conjunction with the Round U-Bolts. See
Assembly Guides for more information.
The Square U-Bolt measures 3/8"x 7-1/4"Lx1-
7/8"IDx2-1/2"T and is made of Zinc Yellow. The
U-Bolt is used for attaching Bunk Mounting
Brackets and Side Guide Support Bases to the lift
cradle. See Assembly guides for more
information
Item: 3706-10 1/2" Flat washer ZY
The 1/2" USSS Flat washer in Zinc Yellow is used
with the Round U-bolt and 1/2" Lock Nut. See
Assembly Guides for more information.
Item: 3706-07 HHCS 1/2" x 6" Item: 3709-05 Round U-Bolt
The 1/2" x 6" Hex Head Cap Screw is used in the
installation of the cables downwards into the
bolts at the bottom of the lift frame. Does not
include lock nuts or washers. See Assembly
Guides for more information.
Item: 3712-00
Call Toll Free: 1.800.989.3625 or [email protected] 18
Used on the Rear Cradle, Pulley C measures
3"OD x 1"W x 2 Groove. There are 2 per lift.
Does not include bolt w/lube fitting.
Item: 3796-01 5000 Nylatron Pulley A
Marine Grade Carpet used on all Metal Craft
Bunks and Guides. Available in two widths, the
15" width is used on all standard bunks and
guides while the 26" width is used on all deluxe
side guides. Does not include lumber. Please
specify size when ordering.
Standard 15"W Item: 3850-15
Deluxe 26"W item: 3850-26
Used on the side cradle, Pulley A measures 4"OD
x 1.4"Wx 1 Groove. There are 4 per lift. Does not
include bolt w/lube fitting.
Used on the side cradle, Pulley A measures 3"OD
x 1.25"W x 1 Groove. There are 4 per lift. Does
not include bolt w/lube fitting.
Item: 3795-02 4000 Nylatron Pulley B
Item: 3850-XX Bunk/Side Guide Carpet
Item: 3797-01 4000/5000 Nylon rollers
(8) used per lift.
Item: 3796-03 5000 Nylatron Pulley C
Used on the Rear Cradle, Pulley C measures 4"OD
x 1"W x 2 Groove. There are 2 per lift. Does not
include bolt w/lube fitting.
Item: 3795-03 4000 Nylatron Pulley C
Item: 3796-02 5000 Nylatron Pulley B
Used on the Winch Cradle, Pulley B measures
4"OD x 1"W x 1 Groove. There are 2 per lift. Does
not include bolt w/lube fitting.
Used on the Winch Cradle, Pulley B measures
3"OD x 1"W x 1 Groove. There are 2 per lift.
Does not include bolt w/lube fitting.
Item: 3761-03 42" Winch Operating Wheel
42" Winch Operating Wheel, Steel with Black, 2
Spoke - shipped boxed with hardware.
Replacement works with both 4000 & 5000
model Boat Lifts.
Item: 3795-01 4000 Nylatron Pulley A
Item: 1801-XX Replacement Pulley Kit
The Replacement Pulley Kit includes (4) Pulley
A, (2) Pulley B, (2) Pulley C, and (8) 5/8"D
Stainless Bolt Shaft with Lube Fitting. Please
specify model when ordering from below.
4000 Replacement Kit Item: 1801-01
5000 Replacement Kit Item: 1801-02
Call Toll Free: 1.800.989.3625 or [email protected] 19
Item # Stationary Dock Parts Description Qty. Unit Price Extended Item # Floating Dock Parts Description Qty. Unit Price Extended
6270-00 Stationary U-Hook, w/SS Mounting Hdw. 0093-01 3'Wx4'Lx12"D Float
6320-00 Shoreline Clamp for 1-7/8" Pipe 0093-02 4'Wx4'Lx12"D Float
0011-01 "T" Cap for 1-7/8" Pipe 0093-03 5'Wx4'Lx12"D Float
0010-01 "O" Cap for 1-7/8" Pipe 0093-04 6'x4'Lx12"D Float
0065-00 Deck Corner 0076-15 LWF "J" Mntg. Bolt 3/8" Stainless Steel
6340-XX Stationary Shoreline Mounting Kit 0076-13 Galvanized Steel Star Washer
0080-01 3'W Deck End, Punched 0076-11 3/8" SS Lock Nut w/Nylon Insert
0080-02 4'W Deck End, Punched 0076-10 3/8" Flat Washer
0080-03 5'W Deck End, Punched 6700-XX 10" HD Hinge Conn. Kit (2 Male, 2 Female, 2 Pins)
0080-04 6'W Deck End, Punched 6703-00 HD Tee Hinge Kit (2 Male, 2 Female, 2 Pins)
6250-00 3'W X-Brace , Trussed, 12"H Pipe Bracket 6701-XX 10" Heavy Duty Male Hinge
6251-00 4'W X-Brace, Trussed, 12"H Pipe Bracket 6702-XX 10" Heavy Duty Female Hinge
6252-00 5'W X-Brace, Trussed, 12"H Pipe Bracket 6704-00 8" Heavy Duty Tee Hinge
6253-00 6'W X-Brace, Trussed, 12"H Pipe Bracket 6705-00 Std. 2-3/4"L Hinge Pin w/Nylon Bushing &SS Clip
6260-00 Corner Half Brace, Left 6706-00 3-1/4"L Hinge Pin w/N.Bush,Galv. CastleNut & SS Clip
6261-00 Corner Half Brace, Right 6710-00 14"H LWF Locking Conn. Kit (2 Left, 2 Right)
6220-00 12" Square Base Pads (Standard) 6712-00 14"H LWF Locking Plate, Right w/Gus. Arm
6222-00 18" Square Base Pads (Severe Mud) 6711-00 14"H LWF Locking Plate, Left w/Gus. Arm
6230-01 Brown Pipe Cap for 1-7/8" Pipe 7010-00 8"/12" HD Locking Conn. Kit (2Male,2Female)
6230-03 White Pipe Cap for 1-7/8" Pipe 7011-XX 8"H/12"H HD Locking Plate Male
6310-00 Splayed Leg 7012-XX 8"/12" HD Locking Plate Female
6303-XX 7' Auger Bit Kit (S.L. Clamp, Bit, Pipe,Cap) 6770-XX HD Shoreline Moutning Kit, 1-7/8" Pipe
6304-XX 9' Auger Bit Kit (S.L. Clamp, Bit, Pipe,Cap) 6771-04 Sev. Duty Shoreline Mntg. Kit, 2-7/8" Pipe
6305-XX 11' Auger Bit Kit (S.L. Clamp, Bit, Pipe,Cap) 6760-00 3" ID Steel Ring Collar
6210-00 5' HD Schedule 10 Alum. Pipe 6760-01 4" ID Steel Ring Collar
6211-00 7' HD Schedule 10 Alum. Pipe 6766-XX Elongated Holder for 1-7/8" OD Pipe
6212-00 9' HD Schedule 10 Alum. Pipe 6765-XX Cable Tow U-Bolt, 1"IDx3/8", SS
6213-00 11' HD Schedule 10 Aluminum Pipe Include below additional parts items not listed above
0074-11 5/16" Lock Nut w/Nylon Insert
0225-00 Swim Ladder Installation Parts Kit
0074-07 5/16" x 1" HHCS, SS
0224-00 5' Bench Installation Parts Kit
0074-10 5/16" Flat Washer, SS
Accessories Description
6010-00 Swim & Saftey Ladder
6020-XX 5'L Alum. Bench; (Select color option from the right)
6030-00 8" Mooring Cleats
Dock Parts Order Form
MERCHANDISE SUBTOTAL
DISCOUNT
INSTALLATION
Dealer Name:
Ship to Dealer Ship to Customer
Customer Name:
Today's Date: Purchase Order:
SALES TAX
*Please provide customer information for warranty purposes only*
Estimate Order
TOTAL
Address:City, State, Zip:Phone or Email:
Address:City, State, Zip:Phone or Email:
Cloud White Earth Sand Sea Green
Pickup at MCD
For best results, save forms to your desktop and rename them to use the full features prior to entering order information. Email completed forms to [email protected] or fax to: 440.286.7134
Ohio customers must include Sales Tax of 7.00%MCD will contact you within 24 hours regarding shipping costs and payment information.
NA
SHIPPING
20
Connection
Locked
Brace
Braces
Locked
Conection
Hinged
Brace
Hinged
Conection
FLOATING DOCK PARTS & FITTINGS Determine desired shape of dock system, and then specify deck size & color, Hinges, Locking Connections, Shoreline Mounting Kits, Spud Pipe Holders, Finger Braces & Gusset Systems as needed for dock site.
Hinged Connection Hinge sections together Lt.Wgt. H.Duty
(6700-XX) 10" H. Duty Hinge Connection, Complete [2 Male, 2 Female Hinges, 2 Pins] $198.10 yes yes
10" H. Duty Tee Hinge Connection, Complete [2 Male , 2 Tee Hinges, 2 Pins] $208.06 yes yes
10" Heavy Duty Male Hinge $38.19 yes yes
10" Heavy Duty Female Hinge $46.55 yes yes
8" Heavy Duty Tee Hinge $51.53 yes yes
Standard 2¾” L Hinge Pin, w/Nylon Bushing & SS Clip $14.31 yes yes
(6703-00)
(6701-XX)
(6702-XX)
(6704-00)
(6705-00)
(6706-00) Extended 3¼ “L Hinge Pin, w/Nylon Bushing, Galv. Castle Nut & SS Clip $20.39 yes yes
Locking Plate Connection Lock sections together
(6710-00) 14”H LWF Locking Connection, Complete [2 Left & 2 Right Locking Plates] $204.60 yes
(6712-00) 14”H LWF Locking Plate, Right, w/Gusset Arm $51.15 yes
(6711-00) 14”H LWF Locking Plate, Left, w/Gusset Arm $51.15 yes
(7010-00) 8”H / 12”H .D. Locking Connection, Complete [2 Male & 2 Female Plates)] $158.32 yes
(7011-XX) 8”H / 12”H Heavy Duty Locking Plate, Male, Aluminum $42.79 yes
(7012-XX) 8”H / 12”H Heavy Duty Locking Plate, Female, Aluminum $36.37 yes
(7014-XX) 8”H / 12”H Heavy Duty One-Piece Locking Plate, Aluminum $77.59 yes
(7013-XX) 8”H / 12”H H. Duty 1-Piece Locking Conn., Complete [2 One-Piece Plate) $155.18 yes
Connection Braces Connect Finger Docks at 90o
Connection Braces required to attach one section at right angle to another section.
(6721-00) Locked Connection Braces (pair) $311.33 yes
(6722-00) Hinged Connection Braces (pair) $182.64 yes
$91.32 yes
$91.32 yes
Cross Deck Braces
(6731-XX) Cross Deck Brace, Type A (Handrail Brackets to Side rail w/SS Hdw.)
(6732-XX) Cross Deck Brace, Type B (T-Hinges, U_Hooks, Cable Tow U-Bolts
Finger Gussets (w/SS hardware) Gussets strengthen finger docks at main walkway - use reinforced 45o angled braces.
(6751-00) 1-Way Locked Corner Gusset ( ½ finger+walkway) $206.09 yes yes
(6750-00) 1-Way Hinged Corner Gusset ( ½ finger+walkway) $329.75 yes yes
(6754-00) 2-Way Locked Finger Gusset (1 finger+walkway) $309.86 yes yes
(6752-00) 2-Way Hinged Finger Gusset (1 finger+walkway) $454.02 yes yes
(6755-00) 4-Way Locked Finger Gusset (2 fingers+walkway) $501.53 yes yes
(6753-00) 4-Way Hinged Finger Gusset (2 fingers+walkway) $786.91 yes yes
Aluminum Pipe, 1 7/8”OD, w/Auger Bit
(6298-XX) 7’ Sch 10 Alum. Pipe w/Cast Iron Auger Bit & Cap $59.48 yes
(6299-XX) 9’ Sch 10 Alum. Pipe w/Cast Iron Auger Bit & Cap $67.11 yes
(6300-XX) 11’ Sch 10 Alum. Pipe w/Cast Iron Auger Bit & Cap $78.26 yes
Spud Pipe & Cable Holders w/SS hardware
(6760-00) 3” ID Steel Ring Collar $55.79 yes
(6760-01) 4” ID Steel Ring Collar $58.33 yes
(6766-XX) Elongated Holder for 1 7/8” OD Pipe, Aluminum $151.30 yes
(6763-00) Elongated Spud Holder, 1 7/8” or 2 7/8” OD Pipe Custom, Alum $302.60 yes
(6765-XX) Cable Tow U-Bolt, 1”ID x 3/8”, Stainless $18.64 yes yes
(7060-00) 3 ½” ID x 12”H Steel Spud Holder $69.27 yes
(6763-00) Custom Spud Holders & Mounts Available P.O.R. yes yes
Shoreline Mounting Kit, Floating Includes: (2) 3.5’ pipe sections, (2) Male Hinges, (2) Female Hinges, (2) Hinge Pins, (2) Caps, (2) S.L. Clamps
(6770-XX) Heavy Duty, 1 7/8” Pipe $321.39 yes yes
(6771-04) Severe Duty, 2 7/8” Pipe $367.45 yes yes
Horizontal Bumper Bracket See Page 6
(6380-01) Side Mount, L.W. Floating (ea.) $19.57 yes
(6380-01) End Mount (ea.) $19.57 yes yes
(7080-00) Side Mount, H.D. Floating (ea.) $23.76 yes
Vertical Bumper Bracket See Page 6
(6390-00) Side Mount, L.W. Floating, (3.5”x3.5” Post), w/ Cross Deck Brace (ea.) $119.66 yes
(6391-00) Side Mount, L.W. Floating, (3.5”x3.5” Post),w/ Cross Deck Brace (pr.) $147.05 yes
(6390-02) Side Mount, L.W. Floating, (4”x4” Post), w/Cross Deck Brace (ea.) $123.06 yes
(6391-02) Side Mount, L.W. Floating, (4”x4” Post), w/ Cross Deck Brace (pr.) $153.85 yes
(7090-00) Side Mount, Heavy Duty Floating, Std. (3.5”x3.5” Post) (ea.) $38.92 yes
(7090-02) Side Mount, Heavy Duty Floating, Large (4”x4” Post) (ea.) $42.32 yes
Mooring Cleat
(6030-00) Standard 8”L Mooring Cleat, Aluminum (ea.) $27.59 yes yes
seawall
Tee Hinge
Male HingeFloating
Dock
Hinge Pin
Tee Hinge Connection
Female Hinge
Male HingeFloating
Dock
Hinge Pin
Floating
Dock
Hinged Connection
Locking Plate
Floating
Dock
Floating
Dock
Locking Plate
SS Bolt
& Nut
Locking Connection
Female Hinge
Male Hinge
Floating
Dock
Hinge Pin
Pipe DrivenIn Ground
Shoreline Mounting KitShoreline Mounting Kit
ShorelineClamp
1-Way
2-Way
4-Way
Finger
Under DeckSupport
Gussets
21Please include part number from above on the Dock Parts Order Form (page 19) when ordering.
Item Number Qty. Unit Price Extended
1005-011005-021006-01
1125-01-SS1225-01-SS
3755-033756-033760-03
1610-011610-021610-03
1610-04-SS1625-011710-011710-021710-03
1710-04-SS1725-011801-011801-023761-033797-013850-153850-26
26" Winch Operating Wheel
Phone or Email:
Ship to Dealer Ship to Customer Pickup at MCD
4000 Side Cradle Cable
PWC Lift Parts2" Pulley without Chain Link
2" Pulley with Chain Link
Boat Lift Parts
4000-122 Rear Cradle Cable4000 Winch Cable
Address:
Boat & PWC Lift Parts Order Form
850 PWC Winch Kit1200 PWC Winch Kit
Today's Date: Purchase Order:
4000-110 Rear Cradle Cable
*Please provide customer information for warranty purposes only*
Estimate Order
Address:
City, State, Zip:
3 Piece Pulley Replacement Kit850 PWC Winch Cable
1200 PWC Winch Cable
Customer Name:
City, State, Zip:
Phone or Email:
4000 Lorenz Winch5000 Side Cradle Cable
5000-115 Rear Cradle Cable5000-122 Rear Cradle Cable
5000 Winch Cable5000 Lorenz Winch
15"W x 15'L Bunk/Side Guide Carpet
4000 Replacement Pulley Kit
4000/5000 Nylon Rollers
5000 Replacement Pulley Kit42" Winch Operating Wheel
26"W x 15'L Bunk/Side Guide Carpet
TOTAL
Dealer Name:
MERCHANDISE SUBTOTALDISCOUNTSHIPPING
INSTALLATIONSALES TAX
Order Other Parts Below
For best results, save forms to your desktop and rename them to use the full features prior to entering order information. Email completed form to [email protected] or fax to 440.286.7134
Ohio customers must include Sales Tax of 7.00%. MCD will contact you within 24 hours regarding shipping costs and payment information. 22