PARAMETER DICT

Parameter Dictionary

DN99567618Issue 15-1 en

# Nokia Siemens Networks 1 (192)

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for theuse of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted inany form or means without the prior written permission of Nokia Siemens Networks. Thedocumentation has been prepared to be used by professional and properly trained personnel,and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomescustomer comments as part of the process of continuous development and improvement of thedocumentation.

The information or statements given in this documentation concerning the suitability, capacity, orperformance of the mentioned hardware or software products are given “as is” and all liabilityarising in connection with such hardware or software products shall be defined conclusively andfinally in a separate agreement between Nokia Siemens Networks and the customer. However,Nokia Siemens Networks has made all reasonable efforts to ensure that the instructionscontained in the document are adequate and free of material errors and omissions. NokiaSiemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues whichmay not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUTNOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESSOPPORTUNITY OR DATA, THAT MAYARISE FROM THE USE OF THIS DOCUMENT OR THEINFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark ofNokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners,and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2008. All rights reserved.

2 (192) # Nokia Siemens Networks DN99567618Issue 15-1 en


Contents

Contents 3

1 Changes in Parameter Dictionary 11

2 Scope 15

3 SGSN 173.1 Access restriction data (ARD) 173.2 Allocation/retention priority (ARP) 173.3 Allocation/retention priority one (ARP1) 183.4 Allocation/retention priority two (ARP2) 183.5 Allocation/retention priority three (ARP3) 193.6 Attach restriction (CSAR) 193.7 Authentication mode (AUM) 203.8 Average real-time bandwidth (ARTBW) 203.9 BVC reset retries (BRR) 213.10 BVC reset timer (BRT) 213.11 CN identifier (CNID) 223.12 Ciphering mode (CIP) 223.13 CS paging sending time to unknown MS after reset (CPM) 223.14 Data compression (COMP) 233.15 Detach timer (DET) 233.16 Detached subscriber storage time (STT) 243.17 Differentiated services codepoint (DSCP) 243.18 Differentiated services codepoints mapping (DSCPM) 263.19 Enhanced random early detection in Gb buffer (QGB) 263.20 Force to STANDBY (FTS) 273.21 Gb over IP configuration UDP port (ICP) 273.22 GGSN IPv6 network identifier (GNI6) 283.23 GGSN network identifier (GNI) 283.24 GGSN operator identifier (GOI) 293.25 Gs mode (GM) 293.26 Guaranteed bit rate for downlink (DWNBR) 303.27 Guaranteed bit rate for uplink (UPBR) 303.28 Guaranteed bit rate for UTRAN to GERAN in ISHO (IGBR) 313.29 Home subscriber group controlled roaming (HCONTR) 313.30 Identification of lawful interception controllers (LIC) 323.31 IMEI check mode (ICHM) 323.32 IMEI request mode (IRM) 323.33 IP address of the SGSN LIE server (LIP) 333.34 IPv6 acknowledged data header compression (I6HCACK) 333.35 IPv6 unacknowledged data header compression (I6HCUNACK) 343.36 LIC identifier (LID) 343.37 LLC retransmission count (LLCCO) 353.38 LLC retransmission timer (LLCTIM) 353.39 Maximum bit rate for downlink (DWNMAX) 363.40 Maximum bit rate for uplink (UPMAX) 363.41 Maximum bit rate for UTRAN to GERAN in ISHO (IMBR) 37

DN99567618Issue 15-1 en


Contents

3.42 Maximum number of lawful interception browsers connected (LIBC) 373.43 Maximum number of lawful interception controllers connected (LICC) 373.44 Maximum number of octets in information field (LN201I) 383.45 Maximum number of outstanding I frames in LLC layer (LLCIFM) 383.46 MS reachable timer (MSRT) 393.47 N3-request counter for Create PDP Context Requests (N3CRE) 403.48 N3-requests counter for Delete PDP Context Requests (N3DEL) 413.49 N3-requests counter for Echo requests of control plane (N3EC) 413.50 N3-requests counter for echo requests of user plane (N3EU) 423.51 N3-requests counter for Forward Relocation Requests (N3REL) 423.52 N3-requests counter for Identification Requests (N3ID) 433.53 N3-requests counter for SGSN context requests (N3SGCTXT) 433.54 N3-requests counter for Update PDP Context Requests (N3UPD) 443.55 Network resource identifier length (LEN) 443.56 Non-broadcast location area code (NLAC) 453.57 Non-broadcast mobile country code (NMCC) 453.58 Non-broadcast mobile network code (NMNC) 463.59 Non-broadcast routing area code (NRAC) 463.60 Non-guaranteed streaming traffic queue priority (NGQP) 473.61 NS alive retries (NAR) 473.62 NS alive timer (NAT) 483.63 NS block retries (NBR) 483.64 NS block timer (NBT) 493.65 NS reset retries (NRR) 493.66 NS reset timer (NRT) 493.67 NS test timer (NTT) 503.68 NS unblock retries (NUR) 503.69 Null network resource identifier (NNRI) 513.70 Number of simultaneous intercepted subscribers (LSIS) 513.71 Offload periodic RA update timer (OFFP) 523.72 Override the MS READY state timer (ORDY) 523.73 Paging interval timer for 2G (PIT) 533.74 Paging interval timer for 3G (PIT3G) 533.75 Periodic RA update timer (PRAU) 543.76 Port address of the SGSN LIE server (LPA) 543.77 Priority buffer 1 length (P1BL) 553.78 Priority buffer 2 length (P2BL) 553.79 Priority buffer 3 length (P3BL) 563.80 Priority buffer 4 length (P4BL) 563.81 PTMSI signature mode (PSMO) 563.82 RA paging area for 2G (RPA) 573.83 RA paging area for 3G (RPA3G) 573.84 RA paging repetition for 2G (RPR) 583.85 RA paging repetition for 3G (RPR3G) 583.86 Random early detection in GTP buffer (QGTP) 593.87 READY state timer (RDY) 593.88 Real-time bandwidth (RTBW) 603.89 Real-time load percent for 2G (RTL2G) 603.90 Real-time load percent for 3G (RTL3G) 613.91 Real-time PDP context percent (RTCTXT) 613.92 Redundancy elimination (RE) 613.93 Retransmission (RET) 62



3.94 Safety margin percent (SAFEM) 623.95 Scheduling in Gb buffer (QSGB) 633.96 SGSN identifier (SGID) 633.97 SGSN paging area for 2G (SPA) 643.98 SGSN paging area for 3G (SPA3G) 643.99 SNS add retries (SAR) 653.100 SNS changeweight retries (SWR) 653.101 SNS config retries (SCR) 663.102 SNS delete retries (SDR) 663.103 SNS prov timer (SPT) 673.104 STANDBY state timer (STBY) 673.105 Store subscriber data (SSD) 683.106 T3-response timer of Create PDP Context Response (T3CRE) 683.107 T3-response timer of Delete PDP Context Response (T3DEL) 693.108 T3-response timer of Echo response of control plane (T3EC) 693.109 T3-response timer of echo response of user plane (T3EU) 703.110 T3-response timer of Forward Relocation Response (T3REL) 703.111 T3-response timer of Identification Response (T3ID) 713.112 T3-response timer of SGSN context response (T3SGCTXT) 713.113 T3-response timer of Update PDP Context Response (T3UPD) 723.114 T3 tunnel (T3T) 723.115 TCP round trip adjustment (RTTA) 733.116 Techo (TECHO) 733.117 Traffic class (CLASS) 743.118 Traffic handling priority (PRIOR) 743.119 UMTS attach restriction (CSARIU) 753.120 UMTS ciphering mode (CIPIU) 753.121 Utilisation rate dependent cleaning (UDC) 763.122 Utilisation rate zero limit (UDL) 763.123 V42bis users (V42) 773.124 Van Jacobsen header compression (VJHC) 773.125 Visitor subscriber group controlled roaming (VCONTR) 773.126 VLR periodic cleaning start timer (CTIM) 783.127 Weight for scheduling priority one (QP1) 793.128 Weight for scheduling priority two (QP2) 793.129 Weight for scheduling priority three (QP3) 793.130 Weight for scheduling priority four (QP4) 803.131 Window pacing (WP) 803.132 Window pacing decrement percent (WPDEC) 813.133 Window pacing threshold level (WPTH) 81

4 PLMN 834.1 Allow access to GSM subscriber to GSM network (GTOG) 834.2 Allow access to GSM subscriber to UMTS network (GTOU) 834.3 Allow access to UMTS subscriber to GSM network (UTOG) 844.4 Allow access to UMTS subscriber to UMTS network (UTOU) 844.5 Authentication repetition rate for combined IMSI and GPRS attach

(COMB) 854.6 Authentication repetition rate for combined RA and LA update (RALA) 854.7 Authentication repetition rate for GPRS attach (GPRS) 864.8 Authentication repetition rate for IMSI attach (IMSI) 864.9 Authentication repetition rate for MO PDP context activation (MOA) 87

DN99567618Issue 15-1 en


Contents

4.10 Authentication repetition rate for MO PDP context deactivation (MOD) 874.11 Authentication repetition rate for MO SMS (MOSMS) 884.12 Authentication repetition rate for MT SMS (MTSMS) 884.13 Authentication repetition rate for normal RA update (NRA) 884.14 Authentication repetition rate for normal RA update, new visitor

(NRAVIS) 894.15 Authentication repetition rate for periodic RA update (PRA) 894.16 Authentication repetition rate for service request (SREQ) 904.17 Authentication repetition rate in MO GPRS detach (MOGPRS) 904.18 Ciphering mode (CIP) 914.19 CS/PS coordination (CSPS) 914.20 DEFAPN operator identifier (APN) 914.21 Equivalent PLMN list index (EPLIDX) 924.22 Home PLMN 924.23 IMEI check repetition rate for combined IMSI and GPRS attach

(ICOMB) 934.24 IMEI check repetition rate for combined RA and LA update (IRALA) 934.25 IMEI check repetition rate for GPRS attach (IGPRS) 944.26 IMEI check repetition rate for IMSI attach (IIMSI) 944.27 IMEI check repetition rate for MO PDP context activation (IMOA) 944.28 IMEI check repetition rate for MO PDP context deactivation (IMOD) 954.29 IMEI check repetition rate for MO SMS (IMOSMS) 954.30 IMEI check repetition rate for MT SMS (IMTSMS) 964.31 IMEI check repetition rate for normal RA update (INRA) 964.32 IMEI check repetition rate for normal RA update, new visitor (INRAVIS) 964.33 IMEI check repetition rate for periodic RA update (IPRA) 974.34 IMEI check repetition rate for service request (ISREQ) 974.35 IMEI check repetition rate in MO GPRS detach (IMOGPRS) 984.36 IMEI status check from EIR for combined IMSI and GPRS attach

(SCOMB) 984.37 IMEI status check from EIR for GPRS attach (SGPRS) 984.38 IMEI status check from EIR for IMSI attach (SIMSI) 994.39 IMEI status check from EIR for combined RA and LA update (SRALA) 994.40 IMEI status check from EIR for normal RA update (SRA) 1004.41 IMEI status check from EIR for normal RA update, new visitor

(SRAVIS) 1004.42 IMEI status check from EIR for periodic RA update (SPRA) 1014.43 IMEI status check from EIR for MO GPRS detach (SMOGPRS) 1014.44 IMEI status check from EIR for MO PDP context activation (SMOA) 1024.45 IMEI status check from EIR for MO PDP context deactivation

(SMOD) 1024.46 IMEI status check from EIR for MO SMS (SMOSMS) 1034.47 IMEI status check from EIR for MT SMS (SMTSMS) 1034.48 IMEI status check from EIR for service request (SSREQ) 1044.49 LA based equivalent PLMN list index (EPIND) 1044.50 MNC length (MNCL) 1054.51 Mobile country code (MCC) 1054.52 Mobile network code (MNC) 1064.53 PLMN name 1064.54 PTMSI allocation repetition rate for periodic RA update (PPARA) 1074.55 PTMSI allocation repetition rate for service request (PSREQ) 1074.56 PTMSI signature repetition rate for GPRS attach (PGPRS) 107



4.57 PTMSI signature repetition rate for normal RA update (PNRA) 1084.58 PTMSI signature repetition rate for normal RA update, new visitor

(PNRAVIS) 1084.59 PTMSI signature repetition rate for periodic RA update (PPRA) 1094.60 QoS based roaming agreement (QOSROAM) 1094.61 Reject cause code for GSM subscriber to GSM network (RCGTOG) 1104.62 Reject cause code for GSM subscriber to UMTS network (RCGTOU) 1104.63 Reject cause code for R97/98 terminal to GSM network (RC97TOG) 1114.64 Reject cause code for subscriber count rejection (RCSCR) 1114.65 Reject cause code for UMTS subscriber to GSM network (RCUTOG) 1124.66 Reject cause code for UMTS subscriber to UMTS network

(RCUTOU) 1134.67 The black list effect (BLE) 113

5 VLR 1155.1 Index of the VLR (VLR) 1155.2 Location area code (LAC) 1155.3 Mobile country code (MCC) 1165.4 Mobile network code (MNC) 1165.5 Nature of the VLR address (VNA) 1175.6 New VLR ISDN number (NISDN) 1175.7 Tunnelling of messages (TOM) 1175.8 VLR ISDN number (VISDN) 1185.9 VLR signalling network code (VSNC) 1185.10 VLR signalling point code (VSPC) 119

6 LAC 1216.1 LA based equivalent PLMN list index (EPIND) 1216.2 Location Area Code (LAC) 1216.3 Mobile country code (MCC) 1226.4 Mobile Network Code (MNC) 1236.5 Modification type (MTYPE) 1236.6 Output type (OTYPE) 124

7 CELL 1257.1 BSSGP virtual connection identifier (BVCI) 1257.2 Cell identity (CI) 1257.3 LA based equivalent PLMN list index (EPIND) 1267.4 Location area code (LAC) 1267.5 Mobile country code (MCC) 1267.6 Mobile network code (MNC) 1277.7 Network service entity identifier (NSEI) 1277.8 Output cell parameters 1287.9 PAPU unit index (PAPU) 1287.10 Routing area code (RAC) 128

8 NSE 1318.1 Connection type 1318.2 Connection type (CONN) 1318.3 Network service entity identifier (NSEI) 1328.4 Network service entity special functionality (SFUNC) 1328.5 PAPU unit index (PAPU) 133

DN99567618Issue 15-1 en


Contents

9 NS-VC 1359.1 Administrative state 1359.2 Bearer channel identification (BCI) 1359.3 Bearer channel name (BCN) 1369.4 Committed information rate (CIR) 1369.5 Data link connection identifier (DLCI) 1379.6 Endpoint PAPUs (PAPUS) 1379.7 Load sharing mode (SMO) 1379.8 Local UDP port number (LPN) 1389.9 Network service entity identifier (NSEI) 1389.10 Network service virtual connection identifier (NSVCI) 1399.11 Network service virtual connection name (NAME) 1399.12 New committed information rate (NEWCIR) 1409.13 New configuration mode (NEWMODE) 1409.14 New load sharing mode (NEWSMO) 1419.15 New local data weight (NEWLDW) 1419.16 New local sign weight (NEWLSW) 1429.17 New local UDP port number (NEWLPNBR) 1429.18 New network service virtual connection identification name

(NEWNAME) 1439.19 New remote data weight (NEWRDW) 1439.20 New remote IP endpoint (NEWRIPEP) 1449.21 New remote sign weight (NEWRSW) 1449.22 New remote UDP port number (NEWRPNBR) 1459.23 PAPU unit index (PAPU) 1459.24 Remote data weight (RDW) 1469.25 Remote IP endpoint (RIPE) 1469.26 Remote sign weight (RSW) 1469.27 Remote UDP port number (RPNBR) 147

10 Home/Visitor subscriber group 14910.1 Access rights of subscriber group (ACCR) 14910.2 Modification type (MTYPE) 14910.3 Output type (OTYPE) 15010.4 Subscriber group identity number (GRNU) 15010.5 Subscriber group type (STYPE) 15110.6 User rights to roam (URT) 151

11 Home/Visitor access list 15311.1 Access list name (ALNA) 15311.2 Access list number (ALNU) 15311.3 Location area code (LAC) 15411.4 Mobile country code (MCC) 15411.5 Mobile network code (MNC) 15511.6 Output type (OTYPE) 155

12 PAPU group 15712.1 DL forwarding activated (DL) 15712.2 Foreign and random TLLI UL forwarding activated (UL) 15712.3 NSVC PAPU cell control (NPCC) 15812.4 PAPU group action 15812.5 PAPU group configuration model (PGM) 159



12.6 PAPU group identifier (PGI) 15912.7 PAPU group name (PGN) 16012.8 PAPU unit index (PAPU) 160

13 PAPU params 16113.1 Blocking for maintenance (BLO) 16113.2 Mass detach (MD) 16113.3 Multipoint offload phase (PHASE) 16213.4 PAPU unit index (PAPU) 16213.5 Radio access type (RAT) 163

14 HT-CGI 16514.1 Cell identity (CI) 16514.2 Location Area Code (LAC) 16514.3 Mobile country code (MCC) 16614.4 Mobile Network Code (MNC) 16614.5 PAPU index (PAPU) 166

15 APN 16915.1 Access Point Name (APN) 16915.2 Usage of command (USE) 169

16 RNC 17116.1 Global title address (DIG) 17116.2 Information type (TYPE) 17116.3 IP interface name (IPNAME) 17216.4 LA based equivalent PLMN list index (EPIND) 17216.5 Mobile country code (MCC) 17316.6 Mobile network code (MNC) 17316.7 Mobile country code of LA (LAMCC) 17416.8 Mobile network code of LA (LAMNC) 17416.9 Network indicator (NI) 17516.10 New radio network controller name (NNAME) 17516.11 PAPU group identifier (PGI) 17616.12 PAPU unit index (PAPU) 17616.13 Radio network controller identification (RNCID) 17616.14 Radio network controller name (RNCNAME) 17716.15 Radio network controller parameter set (PSET) 17816.16 Radio network controller parameter set name (PNAME) 17816.17 Radio network controller state (STATE) 17916.18 Relation type (RT) 17916.19 RNC connect action 18016.20 Routing area code list (RACL) 18016.21 Routing area code list add (RACLA) 18016.22 Routing area code list remove (RACLR) 18116.23 Signalling point code (SPC) 18116.24 Type of address (TOA) 18216.25 Type of RNC (TYPE) 182

17 IP 18517.1 Application identifier (APP) 18517.2 Index of source IP index for application (INDEX) 186

DN99567618Issue 15-1 en


Contents

17.3 Source IP address for application (ADDRESS) 18617.4 Source IP address version (VER) 18717.5 Unit index 18717.6 Unit type 188

18 Related MML command documentation 18918.1 GPRS Network Handling (EJ) commands 18918.2 GPRS Mobility and Session Handling in SGSN (E5) commands 19018.3 Radio Network Controller Parameter Handling in SGSN (E6)

commands 19018.4 GPRS NS Layer Handling (FW) commands 19118.5 Application Configuration Handling (KA) commands 19118.6 PLMN Parameter Handling (MX) commands 192



1 Changes in Parameter DictionaryChanges made between releases SG7.0 and SG6.0 CD8

New parameters

The following parameters have been added:

SGSN

. CNID

. CSARIU

. PIT3G

. RPA3G

. RPR3G

. SPA3G

Modified parameters

The following parameters have been modified:

SGSN

. Paging interval timer (PIT) is now Paging interval timer for 2G (PIT).

. RA paging area (RPA) is now RA paging area for 2G (RPA).

. RA paging repetition (RPR) is now RA paging repetition for 2G (RPR).

. SGSN paging area (SPA) is now SGSN paging area for 2G (SPA).

. Range of the DET parameter has been updated.

. Related commands of the CIPIU parameter have been updated:EJH command added.

DN99567618Issue 15-1 en


Changes in Parameter Dictionary

RNC

. Range of the IPNAME parameter has been updated.

Changes made between releases SG6.0 CD8 and SG6.0 CD7

Modified parameters

SGSN

. Range and Default values of the LSIS parameter have beenchanged. The new Range is 0..30000 and the new Default value is30000.

. Notification of the MSRT parameter has been updated.

. Notification of the PRAU parameter has been updated.

. Notification of the P1BL parameter has been removed.




Removed parameters

The following parameters have been removed:

SGSN

. MODE

Changes made between releases SG6.0 CD7 and SG6.0 CD6

New parameters

The following parameters have been added:

SGSN

. IGBR

. IMBR

Modified parameters

The following parameters have been modified:



RNC

. The RNCNAME parameter was given the same MMLs to its Relatedcommands as the RNCID parameter.

. The E6G command was added to the Related commands of theparameter MCC.

. The E6G command was added to the Related commands of theparameter MNC.

DN99567618Issue 15-1 en


Changes in Parameter Dictionary



2 Scope

The document includes parameter explanations and possible relations to3GPP specifications, and is meant for commissioning engineers and otherSGSN users.

The Parameter Dictionary describes the parameters that you can modifywith the MML commands of the following command groups:

. GPRS Network Handling (EJ)

. GPRS NS Layer Handling (FW)

. PLMN Parameter Handling (MX)

. GPRS Mobility and Session Handling (E5)

. Radio Network Controller Parameter Handling in SGSN (E6)

. Application Configuration Handling (KA)

Based on the corresponding MML commands and files, the parameters inthis document have been organised into the following sections: SGSN,PLMN, VLR, LAC, CELL, NSE, NS-VC, Home/Visitor subscriber group,Home/Visitor access list, PAPU group, PAPU params, HT-CGI, APN,RNC, and IP.

Note

Several parameters with the same name can appear in differentsections of the Parameter Dictionary.

DN99567618Issue 15-1 en


Scope



3 SGSN

3.1 Access restriction data (ARD)

3GPP reference: 3GPP TS 29.002, Mobile Application Part (MAP)specification)

Q3 name:

Modification: On-line

Range: Y - access restriction is in use

N - access restriction is not in use

MML default: Y

Description: With this parameter you can define if the HLR sentAccess Restriction Data (ARD) parameter andthe functionality related to this parameter are usedin SGSN or not.

Related command(s): EJF

EJH

Notification: Parameter is behind the licence SGSN HLR Based2G/3G access control.

3.2 Allocation/retention priority (ARP)

3GPP reference: 3GPP TS 23.107, Quality of Service (QoS) conceptand architecture.

Q3 name: allocationRetentionPriority


Range: 1...3

DN99567618Issue 15-1 en


SGSN

MML default: 3

Description: This parameter defines the allocation/retentionpriority which can be usually used by roamingsubscribers.


EJH

Notification: Parameter is behind the licence SGSN QoS controlfor roaming subscribers.

3.3 Allocation/retention priority one (ARP1)


Q3 name: allocationRetentionPriority1


Range: 0...100

MML default: 100

Description: You can set how much of the real-time bandwidthcan be in use in percents and allow the subscribershaving allocation/retention priority 1 to requireprocedures using real-time bandwith.


EJH

Notification: If you set a value for this parameter, you must alsoset a value for the ARP2 and ARP3 parameters.

The parameter is behind the SGSN CentralizedQos Configuration support licence.

3.4 Allocation/retention priority two (ARP2)




Range: 0...100

MML default: 100



Description: You can set how much of the real-time bandwidthcan be in use in percents and allow the subscribershaving allocation/retention priority 2 to requireprocedures using real-time bandwidth.


EJH

Notification: If you set a value for this parameter, you must alsoset a value for the ARP1 and ARP3 parameters.Parameter is behind the licence SGSN CentralizedQos Configuration support.

3.5 Allocation/retention priority three (ARP3)




Range: 0...100

MML default: 100

Description: You can set how much of the real-time bandwidthcan be in use in percents and allow the subscribershaving allocation/retention priority 3 to requireprocedures using real-time bandwidth.


EJH

Notification: If you set a value for this parameter, you must alsoset a value for the ARP1 and ARP2 parameters.Parameter is behind the licence SGSN CentralizedQos Configuration support.

3.6 Attach restriction (CSAR)

3GPP Reference: No ref

Q3 Name: attachRestriction


Range: Y... attach restriction in use

N... attach restriction not in use

DN99567618Issue 15-1 en


SGSN

MML Default: N

Description: The parameter defines non-ciphering subscriberattach restriction in the 2G SGSN.


EJH

Notification If the 2G SGSN ciphering mode is disabled, thechanges done to this parameter do not affect anyattach or routing area update procedures becausethe ciphering is not in use.

3.7 Authentication mode (AUM)

3GPP reference: No ref.

Q3 name: authenticationMode


Range: Y... authentication in use

N... authentication not in use

AR.. authentication is done when needed

MML default: Y

Description: The parameter defines the authentication mode.


EJH

3.8 Average real-time bandwidth (ARTBW)

3GPP reference: No ref

Q3 name:


Range: 0...64000 kbit/s

MML default: 0

Description: This parameter defines the limit for real averagebitrate used for real-time traffic in PAPU.


EJH



Notification: Parameter is behind the licence SGSN StreamingQoS or SGSN Iu Attach capacity.

3.9 BVC reset retries (BRR)

3GPP Reference: 3GPP TS 48.018, General Packet Radio Service(GPRS); Base Station System (BSS) - ServingGPRS Support Node (SGSN); BSS GPRS Protocol.

Q3 Name: bvcResetRetries


Range: 0..255

MML Default: 3

Description: The parameter defines the number of retries in theBVC reset procedure.


EJH

Notification

3.10 BVC reset timer (BRT)

3GPP Reference: 3GPP TS 48.018, General Packet Radio Service(GPRS); Base Station System (BSS) - ServingGPRS Support Node (SGSN); BSS GPRSProtocol.

Q3 Name: bvcResetTimer


Range: 1..120 (seconds)

MML Default: 3 (seconds)

Description: The parameter guards the reset procedure of aBSSGP virtual connection (BVC).


EJH

Notification

DN99567618Issue 15-1 en


SGSN

3.11 CN identifier (CNID)


Q3 Name: -


Range: 0…4095

MML Default: -

Description: This parameter defines the CN identifier.


EJH

Notification: -

3.12 Ciphering mode (CIP)


Q3 Name: cipheringMode


Range: Y... ciphering mode in use

N... ciphering mode not in use

MML Default: Y

Description: The parameter defines whether ciphering is in use inthe 2G SGSN.


EJH

Notification: If this parameter has value Y, the authenticationmode (AUM) parameter must have value Y.

3.13 CS paging sending time to unknown MS after reset(CPM)


Q3 Name: csPagingSendTime






Description: The parameter defines the time to send the CircuitSwitched (CS) paging to unknown mobile stationsafter a 2G SGSN reset.


EJH

3.14 Data compression (COMP)


Q3 Name: dataCompression


Range: V42... V.42bis is in use

OFF... V.42bis is not in use

MML Default: OFF

Description: The parameter defines data compression.


EJH

Notification

3.15 Detach timer (DET)


Q3 Name: -


Range: 10 min ... 24 hours

Enter the value in the following way: 0...24 - 0...59(hours - minutes).

MML Default: 00—00

DN99567618Issue 15-1 en


SGSN

Description: The detach timer is started when a subscriber isnoticed to be inactive. After the detach timer expires,the 2G SGSN makes a network initiated detach. AnInactive subscriber is a subscriber who has no activePDP context.


EJH

Notification: Value 00–00 means that this parameter is not in use.

3.16 Detached subscriber storage time (STT)


Q3 Name: detachedStorageDay, detachedStorageHour


Range: From 0 to 255. Enter the value in the followingway: 0...255 - 0...23 (days - hours).

MML Default: 24 (hours)

Description: The parameter defines how long the data of adetached subscriber is stored in the visitingsubscriber database of the SGSN.


EJH

Notification:

3.17 Differentiated services codepoint (DSCP)


Q3 Name: -




Range: 000000 ... 111111

000000... Best effort

001010... AF class 1, low drop precedence

001100... AF class 1, medium drop precedence

001110... AF class 1, high drop precedence










101110... expedited forwarding

DEF........ default value

MML Default: CONV = expedited forwarding

STR = AF class 1, low precedence

INT1 = AF class 2, low precedence



BG = Best effort

GTP = expedited forwarding

TRA = expedited forwarding

CHA = expedited forwarding

Description: The parameter defines the value of the differentiatedservices codepoint (DSCP), which is a six-digitbinary value or text string. Besides the predefinedvalues above, customised values can be given.


EJH

Notification: If the value of the differentiated services codepointsmapping (DSCPM) parameter is ALL, you have toenter value DEF for this parameter.

The parameter is behind the SGSN ConversationalQoS licence.

DN99567618Issue 15-1 en


SGSN

3.18 Differentiated services codepoints mapping(DSCPM)


Q3 Name: -


Range: symbolic text string

CONV = Conversational

STR = Streaming

INT1 = Interactive priority level 1



BG = Background

GTP = GTP-C and GGB signalling

TRA = expedited forwarding

CHA = expedited forwarding

MML Default: All = all default values

Description: You can define the differentiated servicescodepoints (DSCP) mapping for traffic classes orsignalling with this parameter.


EJH

Notification: If the value of this parameter is ALL, the value ofthe DSCP parameter must be DEF.

The parameter is behind the SGSN ConversationalQoS licence.

3.19 Enhanced random early detection in Gb buffer(QGB)


Q3 Name: qosGBBuffer


Range: Y... ERED in Gb buffer in use

N... ERED in Gb buffer not in use



MML Default: Y

Description: The parameter defines whether the EnhancedRandom Early Detection (ERED) algorithm is in usein the Gb buffer.


EJH

3.20 Force to STANDBY (FTS)

3GPP Reference: 3GPP TS 24.008, Mobile radio interface Layer 3specification; Core network protocols; Stage 3.

Q3 Name: forceToStandby


Range: Y... force to STANDBY in use

N... force to STANDBY not in use

MML Default: N

Description: The parameter defines whether or not the 2GSGSN forces an MS to the STANDBY state afterGMM procedures.


EJH

Notification: This parameter cannot have value Y if the READYstate timer (RDY) parameter is deactivated.

3.21 Gb over IP configuration UDP port (ICP)


Q3 Name: gbOverIpConfigurationUdp


Range: 1..65535

MML Default: 49999

Description: With this parameter you can define thepreconfigured UDP port number for dynamic Gb overIP.


DN99567618Issue 15-1 en


SGSN

EJH

3.22 GGSN IPv6 network identifier (GNI6)

3GPP Reference: 3GPP TS 23.003, Numbering, addressing andidentification.

Q3 Name: ggsnIPv6NwId


Range: The length of the identifier ranges from 1 to 63alphanumeric and special characters. Allowedcharacters are 'A' ...'Z', 'a' .. 'z', '0' .. '9', '.' and '—' .

The GGSN network identifier cannot end with '.gprs' and cannot start with 'rac', 'lac' or 'sgsn'.Character '*' is also forbidden.

MML Default: —

Description: This parameter is used in case the SGSN has tochoose a default GGSN that supports PDP typeIPv6 on the user plane.


EJH

Notification

3.23 GGSN network identifier (GNI)

3GPP Reference: 3GPP TS 23.003, Numbering, addressing andidentification.

Q3 Name: ggsnNwId


Range: The length of the identifier ranges from 1 to 63alphanumeric and special characters. Allowedcharacters are 'A' .. 'Z', 'a' .. 'z', '0' .. '9', '.' and '—'

The GGSN network identifier cannot end with '.gprs'and cannot start with 'rac', 'lac' or 'sgsn'. Character '*'is also forbidden.

MML Default: -



Description: This parameter defines the GGSN IPv4 networkidentifier. It is used in case the SGSN has to choosea default GGSN that supports PDP type IPv4 on theuser plane.


EJH

Notification

3.24 GGSN operator identifier (GOI)

3GPP Reference: 3GPP TS 23.003, Numbering, addressing andidentification

Q3 Name: ggsnOperatorId


Range: The length of the identifier ranges from 1 to 37characters ('A'..'Z', 'a'..'z', '0'..'9', '.')

This parameter is composed of three labels and ithas to end with '.gprs'. For example, 'mncMNC.mccMCC.gprs'.

MML Default: -

Description: The parameter defines the PLMN GPRS backbonein which the GGSN is located.


EJH

Notification:

3.25 Gs mode (GM)

3GPP Reference: 3GPP TS 23.060, General Packet Radio Service(GPRS) Service description; Stage 2

Q3 Name: gsMode


Range: Y... Gs interface exists

N... Gs interface does not exist

MML Default: Y

DN99567618Issue 15-1 en


SGSN

Description: The parameter defines whether the Gs interfaceexists towards the MSC/VLR or not.


EJH

3.26 Guaranteed bit rate for downlink (DWNBR)

3GPP Reference: 3GPP TS 23.107, Quality of Service (QoS) conceptand architecture.

Q3 Name: guaranteedBitRateForDownlink


Range: The values range from 0 to 63 with steps of 1, from64 to 568 with steps of 8, from 576 to 8640 withsteps of 64 and from 8700 to 16000 with steps 100.

MML Default: 0 kbit/s

Description: This parameter defines the guaranteed bit rate fordownlink traffic for roaming subscriber.


EJH

Notification The parameter is behind the SGSN QoS control forroaming subsribers and HSDPA support licence.

3.27 Guaranteed bit rate for uplink (UPBR)


Q3 Name: guaranteedBitRateForUplink


Range: The values range from 0 to 63 with steps of 1, from64 to 568 with steps of 8, and from 576 to 8640with steps of 64.


Description: This parameter defines the guaranteed bit rate foruplink traffic for roaming subscriber.




EJH

Notification: Parameter is behind the licence SGSN QoS controlfor roaming subsribers.

3.28 Guaranteed bit rate for UTRAN to GERAN in ISHO(IGBR)

3GPP Reference: -

Q3 Name: -


Range: The values range from 0 to 63 kbit/s with steps of 1and from 64 to 472 kbit/s with steps of 8.


Description: The parameter defines the guaranteed bit rate forUTRAN to GERAN in ISHO.


EJH

Notification: The parameter is behind the QoS handling in ISHOprfile parameter.

3.29 Home subscriber group controlled roaming(HCONTR)


Q3 Name: -


Range: Y... home subscriber group controlled roaming is inuse

N... home subscriber group controlled roaming is notin use

MML Default: N

Description: The parameter defines whether the home subscribergroup controlled roaming is in use.


DN99567618Issue 15-1 en


SGSN

EJH

3.30 Identification of lawful interception controllers (LIC)

3GPP reference: No ref.

Q3 name: -


Range: 1..5

MML default:

Description: The parameter defines a certain lawful interceptioncontroller (LIC).


EJH

3.31 IMEI check mode (ICHM)


Q3 Name: imeiCheckMode


Range: Y... IMEI check in use

N... IMEI check not in use

MML Default: Y

Description: The parameter defines whether the IMEI check isin use or not.


EJH

3.32 IMEI request mode (IRM)


Q3 name: -




Range: Y - IMEI request is in use

N - IMEI request is not in use

MML default: N

Description: This parameter defines the IMEI request mode.


EJH

Notification:

3.33 IP address of the SGSN LIE server (LIP)


Q3 Name: licIP


Range: The IP address of the SGSN LIE server, which isactually an IPv4 address for a WO-EX MCHU,contains 7 to 15 characters ('0'..'9','.').

The IP address of the SGSN LIE server, which isactually an IPv6 address for a WO-EX MCHU,contains up to 39 characters (´0´..´9´,'A','B','C','D','E','F',´.´). The delimeter used in IPv6addresses is ':'

0.0.0.0 = LIC not in use.

MML Default:

Description: The parameter defines the IP address of the SGSNLIE server (MCHU address).


EJH

3.34 IPv6 acknowledged data header compression(I6HCACK)


Q3 Name: ipv6HeaderCompression

DN99567618Issue 15-1 en


SGSN


Range: Y… IPv6 header compression in use

N… IPv6 header compression not in use

MML Default: N

Description: The parameter defines whether the IPv6acknowledged data header compression is used ornot.


EJH

3.35 IPv6 unacknowledged data header compression(I6HCUNACK)


Q3 Name: ipv6UnacknowledgedDataHeaderCompression


Range: Y… IPv6 header compression in use

N… IPv6 header compression not in use

MML Default: N

Description: The parameter defines whether the IPv6unacknowledged data header compression is usedor not.


EJH

Notification:

3.36 LIC identifier (LID)


Q3 Name: licIdentifier


Range: 0..4 294 967 295

MML Default: 0



Description: The parameter defines the lawful interceptioncontroller (LIC) identifier.


EJH

3.37 LLC retransmission count (LLCCO)


Q3 Name: llcRetransCount


Range: 1..15

MML Default: 3

Description: The parameter defines the 2G SGSN proposedvalue of the Logical Link Control (LLC)retransmission count.


EJH

Notification:

3.38 LLC retransmission timer (LLCTIM)


Q3 Name: llcRetransTimer


Range: 0.1..409.5 (seconds)


Description: The parameter defines the 2G SGSN proposedvalue of the Logical Link Control (LLC)retransmission timer.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.39 Maximum bit rate for downlink (DWNMAX)


Q3 Name: maximumBitRateForDownlink


Range: The values range from 0 to 63 with steps of 1, from64 to 568 with steps of 8, from 576 to 8640 withsteps of 64 and from 8700 to 16000 with steps 100.


Description: This parameter defines the maximum bit rate fordownlink traffic for roaming subscriber.


EJH

Notification: The parameter is behind the SGSN QoS control forroaming subsribers and HSDPA support licence.

3.40 Maximum bit rate for uplink (UPMAX)


Q3 Name: maximumBitRateForUplink


Range: The values range from 0 to 63 with steps of 1, from64 to 568 with steps of 8, and from 576 to 8640with steps of 64.


Description: This parameter defines the maximum bit rate foruplink traffic for roaming subscriber.


EJH

Notification: Parameter is behind the licence SGSN QoS controlfor roaming subsribers.



3.41 Maximum bit rate for UTRAN to GERAN in ISHO(IMBR)

3GPP Reference: -

Q3 Name: -


Range: The values range from 0 to 63 kbit/s with steps of 1and from 64 to 472 kbit/s with steps of 8.


Description: The parameter defines the maximum bit rate forUTRAN to GERAN in ISHO.


EJH

Notification: The parameter is behind the QoS handling in ISHOprfile parameter.

3.42 Maximum number of lawful interception browsersconnected (LIBC)


Q3 Name: licInterceptionBrowserConnect


Range: 0..5

MML Default: 5

Description: The parameter defines the maximum number oflawful interception browser (LIB) connections.


EJH

3.43 Maximum number of lawful interception controllersconnected (LICC)


DN99567618Issue 15-1 en


SGSN

Q3 Name: licInterceptionControllerConnect


Range: 0..5

MML Default: 5

Description: The parameter defines the maximum number oflawful interception controller (LIC) connections.


EJH

3.44 Maximum number of octets in information field(LN201I)


Q3 Name: Ln201lMaxOctetNumber


Range: 140..1520

MML Default: 1250

Description: The parameter defines the maximum number ofoctets in an information field (N201-I) in the logicallink control (LLC) layer.

The multiplied LN201I and LLCIFM parameterscontain the maximum amount of memory that onesubscriber can get. If there are enoughsimultaneous users with maximum memoryrequirements, the memory capacity of the system isexceeded. So a decrease of either or bothparameters allows more simultaneous users.


EJH

Notification:

3.45 Maximum number of outstanding I frames in LLClayer (LLCIFM)




Q3 Name: llcIFramesMax


Range: 1..255

MML Default: 8

Description: The parameter defines the maximum number ofoutstanding I frames in the LLC layer.

The multiplied LN201I and LLCIFM parameterscontain the maximum amount of memory that onesubscriber can get. If there are enoughsimultaneous users with maximum memoryrequirements, the memory capacity of the system isexceeded. So a decrease of either or bothparameters allows more simultaneous users.


EJH

Notification:

3.46 MS reachable timer (MSRT)

3GPP Reference: 3GPP TS 24.008, Mobile radio interface Layer 3specification; Core network protocols; Stage 3

Q3 Name: msReachableTimerMin, msReachableTimerSec


Range: 0...186–0...59 (minutes - seconds)

Value 00-00 means that the MS reachable timer isnot in use.

MML Default: 120 (minutes)

Description: The parameter defines the timer for triggering animplicit GPRS detach for the subscriber.


EJH

DN99567618Issue 15-1 en


SGSN

Notification: The value set for this parameter has to be higherthan the value of the periodic RA update timer(PRAU) parameter used by the MS.

If you enter value 0 for the PRAU parameter, thevalue of this parameter has to be 0.

Optionality with MS reachable timer (MSRT)parameter and periodic RA update timer (PRAU)parameter values means that the parameters whichare configured with ZEJF command are not usedat all if 250k PAPU mode configuration is installed.Even if it is possible to configure those values withZEJF command, the fixed MS reachable timer andfixed periodic RA update timer parameter valuesare always used (marked with an asterisk *) in250k mode.

3.47 N3-request counter for Create PDP ContextRequests (N3CRE)

3GPP Reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) across theGn and Gp interface

Q3 Name: n3RequestsCounterForCreatePdpContextRequests


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) tosend a create PDP context request message.


EJH

Notification:



3.48 N3-requests counter for Delete PDP ContextRequests (N3DEL)

3GPP Reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) acrossthe Gn and Gp interface

Q3 Name: n3RequestsCounterForDeletePdpContextRequests


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) tosend a delete PDP context request message.


EJH

Notification:

3.49 N3-requests counter for Echo requests of controlplane (N3EC)

3GPP Reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) acrossthe Gn and Gp interface

Q3 Name: n3RequestsCounterForEchoRequestsOfControlPlane


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) tosend an echo request message concerning controlplane.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.50 N3-requests counter for echo requests of userplane (N3EU)

3GPP reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) acrossthe Gn and Gp interface.

Q3 name:


Range: 1...7

MML default: 5

Description: With this parameter you can define the value forthe counter that holds the maximum number ofattempts made by the GPRS Tunnelling Protocol(GTP) to send a echo request message concerninguser plane.


EJH

Notification:

3.51 N3-requests counter for Forward RelocationRequests (N3REL)


Q3 name: -


Range: 1...7

MML default: 5

Description: With this parameter you can define the value forthe counter that holds the maximum number ofattempts made by the GPRS Tunnelling Protocol(GTP) to send a forward relocation requestmessage.


EJH

Notification:



3.52 N3-requests counter for Identification Requests(N3ID)

3GPP Reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) acrossthe Gn and Gp interface.

Q3 Name: n3RequestsCounterForIdentificationRequests


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) tosend an identification request message.


EJH

Notification:

3.53 N3-requests counter for SGSN context requests(N3SGCTXT)

3GPP Reference: 3GPP TS 29.060, General Packet Radio Service(GPRS); GPRS Tunnelling Protocol (GTP) acrossthe Gn and Gp interface.

Q3 Name: n3RequestsCounterForSgsnContextRequests


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) tosend an SGSN context request message.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.54 N3-requests counter for Update PDP ContextRequests (N3UPD)


Q3 Name: n3RequestsCounterForUpdatePdpContextRequests


Range: 1..7

MML Default: 5

Description: With this parameter you can define the value for thecounter that holds the maximum number of attemptsmade by the GPRS Tunnelling Protocol (GTP) to sendan update PDP context request message.


EJH

Notification:

3.55 Network resource identifier length (LEN)


Q3 name: networkResourceIdentifierLenght


Range: 0

5

10

MML default: 0

Description: With this parameter you can identify the NRI lengthin the SGSN.


EJH

Notification:



3.56 Non-broadcast location area code (NLAC)

3GPP Reference: 3GPP TS 23.236, The Intra Domain Connection ofRAN Nodes to Multiple CN Nodes

Q3 Name: -


Range: 1...65533

MML Default:

Description: This parameter defines the non-broadcast locationarea code for the Multipoint offloading process.


EJH

Notification: Parameter is behind the Multipoint Gb and/orMultipoint Iu licence.

If you enter a value for NLAC, you must enter valuesfor NMCC, NMNC, and NRAC as well.

3.57 Non-broadcast mobile country code (NMCC)


Q3 Name: -


Range: Includes three digits.

MML Default:

Description: This parameter defines the non-broadcast mobilecountry code for the Multipoint offloading process.


EJH


If you enter a value for NMCC, you must enter valuesfor NMNC, NLAC, and NRAC as well.

DN99567618Issue 15-1 en


SGSN

3.58 Non-broadcast mobile network code (NMNC)


Q3 Name: -


Range: Includes two or three digits.

MML Default:

Description: This parameter defines the non-broadcast mobilenetwork code for the Multipoint offloading process..


EJH


If you enter a value for NMNC, you must enter valuesfor NMCC, NLAC, and NRAC as well.

3.59 Non-broadcast routing area code (NRAC)


Q3 Name: -


Range: 0...255

MML Default:

Description: This parameter defines the non-broadcast routingarea code for the Multipoint offloading process.


EJH


If you enter a value for NRAC, you must enter valuesfor NMCC, NMNC, and NLAC as well.



3.60 Non-guaranteed streaming traffic queue priority(NGQP)

3GPP Reference: 3GPP TS 23.107, Quality of Service (QoS) conceptand architecture

Q3 Name: nonguaranteedStreamingTrafficQueuePriority


Range: 0...200

MML Default: 200

Description: The parameter sets the weight value for non-guaranteed streaming traffic queue.


EJH


3.61 NS alive retries (NAR)

3GPP Reference: 3GPP TS 48.016, General Packet Radio Service(GPRS); Base Station System (BSS) - Serving GPRSSupport Node (SGSN) Interface; Network Service

Q3 Name: nsAliveRetries


Range: 0..255

MML Default: 10

Description: The parameter defines the number of retries in thenetwork service (NS) alive procedure.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.62 NS alive timer (NAT)

3GPP Reference: 3GPP TS 48.016, General Packet Radio Service(GPRS); Base Station System (BSS) - ServingGPRS Support Node (SGSN) Interface; NetworkService

Q3 Name: nsAliveTimer




Description: The parameter modifies the NS alive timer.


EJH

Notification:

3.63 NS block retries (NBR)


Q3 Name: nsBlockRetries


Range: 0..255

MML Default: 3

Description: The parameter defines the number of retries in theNS block procedure.


EJH

Notification:



3.64 NS block timer (NBT)


Q3 Name: nsBlockTimer




Description: The parameter defines the NS block timer.


EJH

Notification:

3.65 NS reset retries (NRR)


Q3 Name: nsResetRetries


Range: 0..255

MML Default: 255

Description: The parameter defines the number of retries in theNS reset procedure.


EJH

Notification:

3.66 NS reset timer (NRT)


DN99567618Issue 15-1 en


SGSN

Q3 Name: nsResetTimer




Description: The parameter defines the NS reset timer.


EJH

3.67 NS test timer (NTT)


Q3 Name: nsTestTimer




Description: The parameter defines the periodicity of the networkservice virtual connection (NS-VC) test procedure.


EJH

Notification:

3.68 NS unblock retries (NUR)


Q3 Name: nsUnblockRetries


Range: 0..255

MML Default: 3



Description: The parameter defines the number of retries in thenetwork service (NS) unblock procedure.


EJH

3.69 Null network resource identifier (NNRI)


Q3 Name: -


Range: 0..31

MML Default:

Description: This parameter defines the null network resourceidentifier.


EJH


3.70 Number of simultaneous intercepted subscribers(LSIS)

3GPP Reference: No ref.

Q3 Name: licSimultaneousInterceptionSubscriber


Range: 0..30000

Value 0 means that the lawful interception is not inuse.

MML Default: 30000

Description: The parameter defines the number of simultaneousintercepted subscribers.


EJH

DN99567618Issue 15-1 en


SGSN

Notification:

3.71 Offload periodic RA update timer (OFFP)


Q3 Name: -


Range: 1 second...240 minutes (minutes - seconds)

MML Default: 4 seconds

Description: This parameter defines the offload periodic RAupdate timer.


EJH


3.72 Override the MS READY state timer (ORDY)

3GPP Reference: 3GPP TS 24.008, Mobile radio interface Layer 3specification; Core network protocols; Stage 3

Q3 Name: -


Range: Y... override the MS READY state timer value

N... MS READY state timer value in use

MML Default: N

Description: The parameter defines whether the 2G SGSNoverrides the value of the READY state timerrequested by the MS.


EJH



3.73 Paging interval timer for 2G (PIT)


Q3 Name: -


Range: 1..186–0...59 (minutes - seconds)

MML Default: 00–00 (not used)

Description: The parameter defines the interval of Routing Area(RA) wide and SGSN wide pagings if the MS doesnot respond (for example, if it is out of the radiocoverage during the paging).


EJH

Notification: Paging is stopped when the MS reachable timer(MSRT) expires.

3.74 Paging interval timer for 3G (PIT3G)


Q3 Name: -


Range: 1..186–0...59 (minutes - seconds)

MML Default: 00–00 (not used)

Description: The parameter defines the interval of Routing Area(RA) wide and SGSN wide pagings if the MS doesnot respond (for example, if it is out of the radiocoverage during the paging).


EJH

Notification: Paging is stopped when the MS reachable timer(MSRT) expires.

DN99567618Issue 15-1 en


SGSN

3.75 Periodic RA update timer (PRAU)


Q3 Name: periodicRaUpdateTimerMin,periodicRaUpdateTimerSec


Range: Enter the value in minutes and seconds (min-sec).The values range:

2..62 seconds with a 2 second step

1..31 minutes with a 1 minute step


Value 00-00 means that this parameter is not in use.

MML Default: 54 minutes

Description: The parameter indicates the interval of the MS'speriodic RA update.


EJH

Notification: The value set for this parameter has to be smallerthan the value set for the MS reachable timer(MSRT) parameter.

If you enter value 0 for this parameter, the value ofthe MSRT parameter has to be 0.

Optionality with MS reachable timer (MSRT)parameter and periodic RA update timer (PRAU)parameter values means that the parameters whichare configured with ZEJF command are not used atall if 250k PAPU mode configuration is installed.Even if it is possible to configure those values withZEJF command, the fixed MS reachable timer andfixed periodic RA update timer parameter values arealways used (marked with an asterisk *) in 250kmode.

3.76 Port address of the SGSN LIE server (LPA)


Q3 Name: licPort




Range: 0..65535

MML Default: -

Description: The parameter defines the port address of the SGSNLIE server (MCHU port).


EJH

3.77 Priority buffer 1 length (P1BL)


Q3 Name: priorityBuffer1Length

Modification On-line

Range: 5...85 with steps of 5

MML Default: 10

Description: The parameter defines the buffer length for thescheduling priority one Gb buffer as a percent of thetotal memory.


EJH






MML Default: 20

Description: The parameter defines the buffer length for thescheduling priority two Gb buffer as a percent of thetotal memory.


EJH

DN99567618Issue 15-1 en


SGSN






MML Default: 30

Description: The parameter defines the buffer length for thescheduling priority three Gb buffer as a percent ofthe total memory.


EJH






MML Default: 40

Description: The parameter defines the buffer length for thescheduling priority four Gb buffer as a percent of thetotal memory.


EJH

3.81 PTMSI signature mode (PSMO)


Q3 Name: ptmsiSignatureMode


Range: Y... PTMSI signature in use



N... PTMSI signature not in use

MML Default: Y

Description: The parameter defines the Packet Temporary MobileSubscriber Identity (PTMSI) signature reallocationmode.


EJH

Notification: A PTMSI signature is reallocated only when aPTMSI is also reallocated.

3.82 RA paging area for 2G (RPA)


Q3 Name: raPagingArea


Range: 1..5

MML Default: 2

Description: The parameter defines how many times the RoutingArea (RA) wide paging is sent.


EJH

Notification:

3.83 RA paging area for 3G (RPA3G)


Q3 Name: raPagingArea


Range: 1..5

MML Default: 2

Description: The parameter defines how many times the RoutingArea (RA) wide paging is sent.


EJH

DN99567618Issue 15-1 en


SGSN

Notification:

3.84 RA paging repetition for 2G (RPR)


Q3 Name: raPagingRepetition


Range: 0.1..25 (seconds)

MML Default: 3.5 (seconds)

Description: The parameter defines for how long the systemwaits for a paging response before repeating thepage.


EJH

Notification:

3.85 RA paging repetition for 3G (RPR3G)


Q3 Name: raPagingRepetition


Range: 0.1..25 (seconds)

MML Default: 3.5 (seconds)

Description: The parameter defines for how long the systemwaits for a paging response before repeating thepage.


EJH

Notification:



3.86 Random early detection in GTP buffer (QGTP)


Q3 Name: qosGTPBuffer


Range: Y... RED in GTP buffer in use

N... RED in GTP buffer not in use

MML Default: Y

Description: The parameter defines whether or not the randomearly detection (RED) algorithm is used in the GTPbuffer.


EJH

Notification:

3.87 READY state timer (RDY)


Q3 Name: readyStateTimerMin, readyStateTimerSec


Range: Enter the value in minutes and seconds (min-sec).



36..186 minutes with a 6 second step

Value 00-00 means that the READY state timer isnot in use.

Value 00-01 means that the READY state timer isdeactivated and the MS remains in the READYstate.


Description: The parameter controls the time an MS and the 2GSGSN MM context remain in the READY state.


EJH

DN99567618Issue 15-1 en


SGSN

Notification: This parameter cannot be deactivated if the force toSTANDBY (FTS) parameter has value Y.

3.88 Real-time bandwidth (RTBW)


Q3 Name: realtimeBandwidth


Range: 0...64000 kbit/s

MML Default: 0

Description: The parameter sets a limit on PAPU's total bitratecapacity used for real-time traffic.


EJH

Notification The bitrate is based on the Gn interface bitrate,which is GTP payload. Parameter is behind thelicence SGSN Streaming QoS or SGSN Iu Attachcapacity.

3.89 Real-time load percent for 2G (RTL2G)

3GPP reference: 3GPP TS 23.107, Quality of Service (QoS) conceptand architecture

Q3 name: -


Range: 0-100%

MML default: 100%

Description: This parameter defines how many percents fromARTBW can be utilised by 2G real-time traffic.


EJH




3.90 Real-time load percent for 3G (RTL3G)


Q3 name: -


Range: 0-100%

MML default: 100%

Description: This parameter defines how many percents fromARTBW can be utilised by 3G real-time traffic.


EJH


3.91 Real-time PDP context percent (RTCTXT)


Q3 name: -


Range: 0-100%

MML default: 100%

Description: This parameter defines how many percents fromcontexts can be used for real-time traffic.


EJH


3.92 Redundancy elimination (RE)


DN99567618Issue 15-1 en


SGSN

Q3 Name: redundancyElimination


Range: ON... TCP redundancy elimination is enabled

OFF... TCP redundancy elimination is disabled

CHECKSUM... TCP redundancy elimination withTCP checksum verification is enabled

MML Default: OFF

Description: The parameter defines whether duplicated oralready MS-acknowledged TCP packets aredropped from Gb buffer (with or without TCPchecksum verification) or not.


EJH

Notification: Parameter is behind the licence SGSN TCP/IPOptimisation.

3.93 Retransmission (RET)


Q3 Name: retransmission


Range: 1..3

MML Default: 2

Description: The parameter defines the maximum number of theretransmission times of Short Message Service(SMS) over GPRS data.


EJH

3.94 Safety margin percent (SAFEM)


Q3 name: -




Range: 0-100%

MML default: 0%

Description: This parameter defines the safety margin percent ofreal-time traffic.


EJH


3.95 Scheduling in Gb buffer (QSGB)


Q3 Name: qosSchedulingGBBuffer


Range: Y... scheduling in Gb buffer in use

N... scheduling in Gb buffer not in use

MML Default: Y

Description: The parameter defines whether or not the schedulingalgorithm is used in the Gb buffer. If it is not used,the weights of priorities are not used.


EJH

Notification:

3.96 SGSN identifier (SGID)

3GPP reference: 3GPP TS 23.236, The Intra Domain Connection ofRAN Nodes to Multiple CN Nodes

Q3 name: sgsnIdentifier


Range: 0...31

MML default:

Description: With this parameter you can identify the SGSNidentifier.

DN99567618Issue 15-1 en


SGSN


EJH

Notification: This parameter does not have a default value.

3.97 SGSN paging area for 2G (SPA)


Q3 Name: sgsnPagingArea


Range: 0..5

MML Default: 0

Description: The parameter defines how many times the 2GSGSN wide paging is repeated. 2G SGSN widepagings are performed when a maximum number ofrouting area wide pagings have been performed.


EJH

Notification:

3.98 SGSN paging area for 3G (SPA3G)


Q3 Name: sgsnPagingArea


Range: 0..5

MML Default: 0

Description: The parameter defines how many times the 2GSGSN wide paging is repeated. 2G SGSN widepagings are performed when a maximum number ofrouting area wide pagings have been performed.


EJH

Notification:



3.99 SNS add retries (SAR)


Q3 Name: -


Range: 0..255

MML Default: 3

Description: This parameter defines the number of SNS-ADDPDU retries in the Sub-Network Service (SNS) Addprocedure.


EJH

Notification:

3.100 SNS changeweight retries (SWR)


Q3 Name: -


Range: 0..255

MML Default: 3

Description: This parameter defines the number of SNS-CHANGEWEIGHT PDU retries in the SNSChangeWeight procedure.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.101 SNS config retries (SCR)


Q3 Name: -


Range: 0..255

MML Default: 3

Description: This parameter defines the number of SNS-CONFIGPDU retries in the SNS Configuration procedure.


EJH

Notification:

3.102 SNS delete retries (SDR)


Q3 Name: -


Range: 0..255

MML Default: 3

Description: This parameter defines the number of SNS-DELETEPDU retries in the SNS Delete procedure.


EJH

Notification:



3.103 SNS prov timer (SPT)


Q3 Name: -




Description: This parameter defines the interval of Sub-NetworkService (SNS) prov timer. The SNS prov timerguards the Internet Protocol (IP) SNS procedures.


EJH

Notification:

3.104 STANDBY state timer (STBY)


Q3 Name: -


Range: Enter the value in minutes and seconds (min-sec).The values range:




Value 00-00 means that the STANDBY state timer isnot in use.


Description: The parameter controls the time an MS returns tothe coverage. After that time a new attach isneeded.


EJH

Notification:

DN99567618Issue 15-1 en


SGSN

3.105 Store subscriber data (SSD)

3GPP reference: 3GPP TS 29.002, Mobile Application Part (MAP)specification)

Q3 name: -


Range: Y - subscriber data is stored

N - subscriber data is discarded

MML default: N

Description: With this parameter you can define if the subscriberdata received from HLR is stored or not in theSGSN subscriber database when subscriber'saccess to SGSN is rejected due to AccessRestriction Data (ARD) parameter valuereceived from HLR.


EJH

Notification: Parameter is behind the licence SGSN HLR Based2G/3G access control.

3.106 T3-response timer of Create PDP ContextResponse (T3CRE)


Q3 Name: n3ResponseTimerForCreatePdpContextRequests


Range: 1..10 (seconds) (1 second step)


Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for acreate PDP context response message to a createPDP context request message.




EJH

Notification:

3.107 T3-response timer of Delete PDP ContextResponse (T3DEL)


Q3 Name: t3ResponseTimerOfDeletePdpContextResponse




Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for a deletePDP context response message to a delete PDPcontext request message.


EJH

Notification:

3.108 T3-response timer of Echo response of controlplane (T3EC)


Q3 Name: t3ResponseTimerOfEchoResponseOfControlPlane


Range: 3..15 (seconds) (3 seconds step)


Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for an echoresponse message to an echo request messageconcerning control plane.

DN99567618Issue 15-1 en


SGSN


EJH

3.109 T3-response timer of echo response of user plane(T3EU)


Q3 name: -


Range: 3..15 (seconds) (3 seconds step)

MML default: 3 (seconds)

Description: With this parameter you can define the value forthe timer that holds the maximum waiting time for aecho response message to a echo requestmessage concerning user plane.


EJH

Notification:

3.110 T3-response timer of Forward RelocationResponse (T3REL)


Q3 name: -



MML default: 3 (seconds)

Description: With this parameter you can define the value forthe timer that holds the maximum waiting time for aforward relocation response message to a forwardrelocation request message.




EJH

Notification:

3.111 T3-response timer of Identification Response(T3ID)


Q3 Name: t3ResponseTimerOfIdentificationResponse




Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for anidentification response message to an identificationrequest message.


EJH

Notification:

3.112 T3-response timer of SGSN context response(T3SGCTXT)


Q3 Name: t3ResponseTimerOfSgsnContextResponse




DN99567618Issue 15-1 en


SGSN

Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for anSGSN context response message to an SGSN contextrequest message.


EJH

Notification:

3.113 T3-response timer of Update PDP ContextResponse (T3UPD)


Q3 Name: n3ResponseTimerForUpdatePdpContextRequests




Description: With this parameter you can define the value for thetimer that holds the maximum waiting time for anupdate PDP context response message to an updatePDP context request message.


EJH

Notification:

3.114 T3 tunnel (T3T)


Q3 Name: t3Tunnel






Description: The parameter defines the timer controlling the timePacket Data Units (PDU) are being forwarded from theold 2G SGSN to the new 2G SGSN as part of theinter-SGSN routing area update procedure.


EJH

Notification:

3.115 TCP round trip adjustment (RTTA)


Q3 Name: tcpRoundTripAdjustment


Range: Y... TCP RTT adjustment is enabled

N... TCP RTT adjustment is disabled

MML Default: N

Description: The parameter enables or disables the delay of TCPSYN-ACK in MO sessions or TCP ACK in MTsessions.


EJH


3.116 Techo (TECHO)


Q3 Name: techo


Range: 60..600 (seconds) with a 30 second step


Description: The parameter defines the timer holding the timeinterval for the path validation procedure.

DN99567618Issue 15-1 en


SGSN


EJH

Notification:

3.117 Traffic class (CLASS)


Q3 name: trafficClass


Range: C = conversational

S = streaming

I = interactive

B = background

MML default: I

Description: This parameter defines the traffic class which canbe used by roaming subscriber at most.


EJH

Notification: The parameter is behind the SGSN ConversationalQos licence.

3.118 Traffic handling priority (PRIOR)


Q3 name: trafficHandlingPriority


Range: 1...3

MML default: 3

Description: This parameter defines the traffic handling prioritywhich can be used by roaming subscriber at most.


EJH



Notification: Parameter is behind the licence SGSN QoS controlfor roaming subscribers.

3.119 UMTS attach restriction (CSARIU)


Q3 Name: UMTSattachRestriction


Range: Y... UMTS attach restriction is in use

N... UMTS attach restriction is not in use

MML Default: N

Description: This parameter defines the usage of non-cipheringsubscriber UMTS attach restriction in the SGSN.


EJH

Notification: If the SGSN ciphering mode is disabled, the changesdone to this parameter do not affect any attach orrouting area update procedures because theciphering is not in use.

3.120 UMTS ciphering mode (CIPIU)


Q3 Name: -


Range: Y... UMTS ciphering mode is in use

N... UMTS ciphering mode is not in use

MML Default: Y

Description: This parameter defines the UMTS ciphering mode inSGSN. The parameter deals with non-standard A5algorithms.


EJH

Notification: -

DN99567618Issue 15-1 en


SGSN

3.121 Utilisation rate dependent cleaning (UDC)


Q3 Name: utilDependentCleaning


Range: 5..100 (%)

0... no utilisation dependent cleaning

MML Default: 80 (%)

Description: The parameter defines the level that the SGSNsubscriber database utilisation rate must reach to startcleaning the database.


EJH

Notification: The value of this parameter has to be less than orequal to the value of the utilisation rate zero limit(UDL) parameter.

3.122 Utilisation rate zero limit (UDL)


Q3 Name: utilZeroLimit


Range: 5..100 (%)

MML Default: 100 (%)

Description: The parameter defines the upper limit for theutilisation rate of the SGSN subscriber databaseafter which the allowed detach time of the subscriberis decreased to zero.


EJH

Notification: The value of this parameter has to be greater than orequal to the utilisation rate dependent cleaning(UDC) parameter. If the UDC parameter has value 0,this parameter has no effect.



3.123 V42bis users (V42)


Q3 Name: v42bisUsers


Range: 10..100 (%) with a 10 % step

MML Default: 20 (%)

Description: The parameter defines the max. proportion(percentage) of users per PAPU that can have V.42negotiated for their simultaneously active PDPcontexts.


EJH

Notification:

3.124 Van Jacobsen header compression (VJHC)


Q3 Name: headerCompression


Range: Y... Van Jacobsen header compression is in use

N... Van Jacobsen header compression is not in use

MML Default: N

Description: The parameter defines whether the Van Jacobsenheader compression is used or not.


EJH

Notification:

3.125 Visitor subscriber group controlled roaming(VCONTR)


DN99567618Issue 15-1 en


SGSN

Q3 Name: -


Range: Y... visitor subscriber group controlled roaming is inuse

N... visitor subscriber group controlled roaming isnot in use

MML Default: N

Description: The parameter defines whether the visitorsubscriber group controlled roaming is in use ornot.


EJH

Notification:

3.126 VLR periodic cleaning start timer (CTIM)


Q3 Name: vlrCleanStartHour, vlrCleanStartMin


Range: 0..23 - 0..59 (hours - minutes)

MML Default: Value 00-00 means that the VLR periodic cleaningstarts at midnight 00:00.

Description: The parameter defines the time when the VLRsubscriber database cleaning process starts.

The periodic cleaning can be disabled by givingvalue 99-N, in other words, 99 for hours and anyvalue for minutes.

Note that in some cases it is possible that periodiccleaning is not run when the utilisation ratedependent cleaning is enabled.


EJH

Notification:



3.127 Weight for scheduling priority one (QP1)


Q3 Name: qosSchedulingPriority1


Range: 25..90 with steps of 5

MML Default: 50

Description: The parameter defines the relative capacity of delayclass 1 compared to the other delay classes.


EJH

Notification: If this parameter is in use, it affects other delayclasses so that a lower priority cannot be greaterthan a higher priority but they can be equal.

3.128 Weight for scheduling priority two (QP2)


Q3 Name: -



MML Default: 30



EJH


3.129 Weight for scheduling priority three (QP3)


DN99567618Issue 15-1 en


SGSN

Q3 Name: -



MML Default: 15



EJH


3.130 Weight for scheduling priority four (QP4)


Q3 Name: -



MML Default: 5



EJH


3.131 Window pacing (WP)


Q3 Name: -


Range: Y... window pacing is enabled

N... window pacing is disabled



MML Default: N

Description: The parameter defines whether the decreasing ofTCP acknowledge window size (TCP RWIN) in theUL direction is used or not.


EJH


3.132 Window pacing decrement percent (WPDEC)


Q3 Name: -


Range: 5...50 with steps of 5 (%)

MML Default: 20

Description: The parameter defines the decrease value of theTCP RWIN size.


EJH

Notification: The parameter has no meaning if the window pacing(WP) parameter is set to value N.

3.133 Window pacing threshold level (WPTH)


Q3 Name: -


Range: 10...90 with steps of 10 (%)

MML Default: 50

Description: The parameter defines the percentage of thethreshold level for Gb buffer.


EJH

DN99567618Issue 15-1 en


SGSN

Notification: The parameter has no meaning if the window pacing(WP) parameter is set to value N.



4 PLMN

4.1 Allow access to GSM subscriber to GSM network(GTOG)


Q3 name: -


Range: Y

N

NOT

MML default: NOT

Description: This parameter sets access right for a GSMsubscriber to the GSM network.

Related command(s): MXN

MXP

Notification:

4.2 Allow access to GSM subscriber to UMTS network(GTOU)


Q3 name: -


Range: Y

N

DN99567618Issue 15-1 en


PLMN

NOT

MML default: NOT

Description: This parameter allows access to GSM subscriber toUMTS network.


MXP

Notification:

4.3 Allow access to UMTS subscriber to GSM network(UTOG)


Q3 name: -


Range: Y

N

NOT

MML default:

Description: This parameter allows access to UMTS subscriberto GSM network.


MXP

Notification:

4.4 Allow access to UMTS subscriber to UMTS network(UTOU)


Q3 name: -


Range: Y

N



NOT

MML default: NOT

Description: This parameter allows access to UMTS subscriberto UMTS network.


MXP

Notification:

4.5 Authentication repetition rate for combined IMSIand GPRS attach (COMB)


Q3 Name: -


Range: 0..255

MML Default: 1

Description: The parameter defines the frequency how oftenauthentication needs to be performed within acombined GPRS and IMSI attach.


MXP

Notification: If ciphering is required and the subscriber is new inthe SGSN (old ciphering parameters cannot befound), authentication has to be performed in anycase.

4.6 Authentication repetition rate for combined RA andLA update (RALA)


Q3 Name: -


Range: 0..255

MML Default: 0

DN99567618Issue 15-1 en


PLMN

Description: The parameter defines how many times a particularevent occurs before an authentication needs to beperformed.


MXP

4.7 Authentication repetition rate for GPRS attach(GPRS)


Q3 Name: -


Range: 0..255

MML Default: 1

Description: The parameter defines how often authenticationneeds to be performed within a GPRS attach.


MXP

Notification: If ciphering is required and the subscriber is new inthe SGSN (old ciphering parameters cannot befound), authentication has to be performed in anycase.

4.8 Authentication repetition rate for IMSI attach (IMSI)


Q3 Name: -


Range: 0..255

MML Default: 1



MXP



4.9 Authentication repetition rate for MO PDP contextactivation (MOA)


Q3 Name: -


Range: 0..255

MML Default: 0

Description: The parameter defines how many times a particularevent occurs before authentication needs to beperformed.


MXP

4.10 Authentication repetition rate for MO PDP contextdeactivation (MOD)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

DN99567618Issue 15-1 en


PLMN

4.11 Authentication repetition rate for MO SMS(MOSMS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.12 Authentication repetition rate for MT SMS (MTSMS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.13 Authentication repetition rate for normal RA update(NRA)


Q3 Name: -




Range: 0..255

MML Default: 0



MXP

4.14 Authentication repetition rate for normal RAupdate, new visitor (NRAVIS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.15 Authentication repetition rate for periodic RAupdate (PRA)


Q3 Name: -


Range: 0..255

MML Default: 0



DN99567618Issue 15-1 en


PLMN

MXP

4.16 Authentication repetition rate for service request(SREQ)


Q3 name: -


Range: 0...255

MML default: 0

Description: This parameter sets authentication repetition ratefor service request.


MXP

Notification:

4.17 Authentication repetition rate in MO GPRS detach(MOGPRS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP



4.18 Ciphering mode (CIP)


Q3 Name: -


Range: Y.. The ciphering is in use.

N..The ciphering is not in use.

MML Default: Y

Description: The parameter defines the usage of ciphering.


MXP

4.19 CS/PS coordination (CSPS)

3GPP reference: 3GPP TS 23.251, Network Sharing Architectureand functional description

Q3 name: -


Range: Y - The CS/PS coordination is in use

N - The CS/PS coordination is not in use

MML default: N

Description: The parameter defines the usage of CS/PScoordination. When the parameter has value Y,SGSN requests CS/PS coordination from the RNCif needed.


MXP

Notification:

4.20 DEFAPN operator identifier (APN)


Q3 Name: -

DN99567618Issue 15-1 en


PLMN


Range: The length of the identifier ranges from 6 to 37alphabetical and special characters.

The last part of the APN string has to be .GPRS.Allowed characters are 'A' .. 'Z', 'a' .. 'z', '.' and '0'..'9'.

By giving value 0 for this parameter you can restorethe default value.

MML Default: -

Description: The parameter defines the DEFAPN operatoridentifier.


MXP

Notification: There can be a maximum of ten unique DEFAPNoperator identifiers in the database.

4.21 Equivalent PLMN list index (EPLIDX)


Q3 Name: -


Range: 1..10

MML Default: -

Description: The parameter defines the equivalent PLMN listindex.


MXP

4.22 Home PLMN


Q3 Name: -


Range: Y... home PLMN



N... visitor PLMN

MML Default: N

Description: The parameter defines the roaming status of thesubscriber.

Related command(s): MXA

4.23 IMEI check repetition rate for combined IMSI andGPRS attach (ICOMB)


Q3 Name: -


Range: 0..255

MML Default: 1

Description: The parameter defines how many times a particularevent occurs before the IMEI needs to be checked.


MXP

4.24 IMEI check repetition rate for combined RA and LAupdate (IRALA)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

DN99567618Issue 15-1 en


PLMN

4.25 IMEI check repetition rate for GPRS attach (IGPRS)


Q3 Name: -


Range: 0..255

MML Default: 1



MXP

4.26 IMEI check repetition rate for IMSI attach (IIMSI)


Q3 Name: -


Range: 0..255

MML Default: 1



MXP

4.27 IMEI check repetition rate for MO PDP contextactivation (IMOA)


Q3 Name: -


Range: 0..255

MML Default: 0





MXP

4.28 IMEI check repetition rate for MO PDP contextdeactivation (IMOD)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.29 IMEI check repetition rate for MO SMS (IMOSMS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

DN99567618Issue 15-1 en


PLMN

4.30 IMEI check repetition rate for MT SMS (IMTSMS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.31 IMEI check repetition rate for normal RA update(INRA)


Q3 Name: -

Modification:§ On-line

Range: 0..255

MML Default: 0



MXP

4.32 IMEI check repetition rate for normal RA update,new visitor (INRAVIS)


Q3 Name: -


Range: 0..255



MML Default 0



MXP

4.33 IMEI check repetition rate for periodic RA update(IPRA)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.34 IMEI check repetition rate for service request(ISREQ)


Q3 name: -


Range: 0...255

MML default: 0

Description: This parameter sets IMEI check repetition rate forservice request..


MXP

Notification:

DN99567618Issue 15-1 en


PLMN

4.35 IMEI check repetition rate in MO GPRS detach(IMOGPRS)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.36 IMEI status check from EIR for combined IMSI andGPRS attach (SCOMB)


Q3 Name: -


Range: Y... the status is checked in the EIR

N... the status is not checked in the EIR

MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of a combinedIMSI and GPRS attach.


MXP

4.37 IMEI status check from EIR for GPRS attach(SGPRS)




Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of GPRS attach.


MXP

4.38 IMEI status check from EIR for IMSI attach (SIMSI)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of IMSI attach.


MXP

4.39 IMEI status check from EIR for combined RA andLA update (SRALA)


Q3 Name: -




DN99567618Issue 15-1 en


PLMN

MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of a combinedRA and LA update.


MXP

4.40 IMEI status check from EIR for normal RA update(SRA)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of normal RAupdate.


MXP

4.41 IMEI status check from EIR for normal RA update,new visitor (SRAVIS)


Q3 Name: -




MML Default: Y



Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of normal RAupdate for a new visitor.


MXP

4.42 IMEI status check from EIR for periodic RA update(SPRA)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of periodic RAupdate.


MXP

4.43 IMEI status check from EIR for MO GPRS detach(SMOGPRS)


Q3 Name: -




MML Default: Y

DN99567618Issue 15-1 en


PLMN

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of mobile-originated GPRS detach.


MXP

4.44 IMEI status check from EIR for MO PDP contextactivation (SMOA)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of mobile-originated PDP context activation.


MXP

4.45 IMEI status check from EIR for MO PDP contextdeactivation (SMOD)


Q3 Name: -




MML Default: Y



Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of mobile-originated PDP context deactivation.


MXP

4.46 IMEI status check from EIR for MO SMS (SMOSMS)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of mobile-originated SMS.


MXP

4.47 IMEI status check from EIR for MT SMS (SMTSMS)


Q3 Name: -




MML Default: Y

Description: The parameter defines whether the internationalmobile equipment identity status of the mobileequipment is checked or not in case of mobile-terminated SMS.


DN99567618Issue 15-1 en


PLMN

MXP

4.48 IMEI status check from EIR for service request(SSREQ)


Q3 name: -


Range: Y - status is checked

N - status is not checked

MML default: Y

Description: This parameter sets IMEI status check from EIR forservice request.


MXP

Notification:

4.49 LA based equivalent PLMN list index (EPIND)


Q3 Name: -


Range: 0x00..0x05, 0xFF

0x00. All equivalent PLMN list indexes. This meansthat equivalent PLMN is used in all lists gathered tobe sent to MS/UE.

0xFF. LA based equivalent PLMN list index is set tonot used value. This means that equivalent PLMN isnot used at all when gathering equivalent PLMN listto be sent to MS/UE.

MML Default: 0xFF

Description: The parameter defines the LA based equivalentPLMN list index.




MXP

4.50 MNC length (MNCL)


Q3 Name: -


Range: SHORT ... two digits

LONG ... three digits

MML Default: SHORT

Description: The parameter defines the MNC length.


MXP

4.51 Mobile country code (MCC)


Q3 Name: -



MML Default: -

Description: The parameter identifies the unique country ofdomicile for the mobile subscriber.


MXP

Notification: By giving value 0 for the mobile country code (MCC)and mobile network code (MNC) parameters you canremove an equivalent PLMN record from a PLMN list.

DN99567618Issue 15-1 en


PLMN

4.52 Mobile network code (MNC)


Q3 Name: -



MML Default: -

Description: The parameter is used to distinguish mobile networksunder one Mobile Country Code (MCC). The MNCidentifies the Home GSM PLMN (HPLMN) of themobile subscriber.


MXP

Notification: By giving value 0 for the mobile country code (MCC)and mobile network code (MNC) parameters you canremove an equivalent PLMN record from a PLMNlist.

4.53 PLMN name


Q3 Name: -


Range: String of up to 15 characters.

Allowed characters are 'A'..'Z', '0'..'9', '-', '_', ' '

MML Default: -

Description: The parameter defines the PLMN name.

Related command(s): MXA

MXD

MXN

MXP



4.54 PTMSI allocation repetition rate for periodic RAupdate (PPARA)


Q3 Name: -


Range: 0..255

MML Default: 0

Description: The parameter defines how many times a particularevent occurs before a new PTMSI needs to beallocated.


MXP

4.55 PTMSI allocation repetition rate for service request(PSREQ)


Q3 name: -


Range: 0...255

MML default: 0

Description: This parameter sets PTMSI allocation repetitionrate for service request.


MXP

Notification:

4.56 PTMSI signature repetition rate for GPRS attach(PGPRS)


DN99567618Issue 15-1 en


PLMN

Q3 Name: -


Range: 0..255

MML Default: 1

Description: The parameter defines how many times a particularevent occurs before a new PTMSI signature needs tobe allocated.


MXP

4.57 PTMSI signature repetition rate for normal RAupdate (PNRA)


Q3 Name: -


Range: 0..255

MML Default: 1

Description: The parameter defines how many times a particularevent occurs before a new PTMSI signature needsto be allocated.


MXP

4.58 PTMSI signature repetition rate for normal RAupdate, new visitor (PNRAVIS)


Q3 Name: -


Range: 0..255

MML Default: 1





MXP

4.59 PTMSI signature repetition rate for periodic RAupdate (PPRA)


Q3 Name: -


Range: 0..255

MML Default: 0



MXP

4.60 QoS based roaming agreement (QOSROAM)


Q3 Name: -


Range: Y...QoS roaming is allowed (the roaming check is notperformed and QoS parameter downgrade accordingto QoS roaming list is not possible)

N...QoS roaming is not allowed (the roaming checkis performed)

MML Default: Y

Description: The parameter defines whether QoS roaming isallowed.


MXP

DN99567618Issue 15-1 en


PLMN

4.61 Reject cause code for GSM subscriber to GSMnetwork (RCGTOG)


Q3 name: -


Range: LA - The location area not allowed

PLMN - The PLMN not allowed

ROAM - The roaming not allowed in this LA

GPRS - The GPRS services not allowed in thisPLMN

CELL - No suitable cells in LA

NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forGSM subscriber to GSM network.


MXP

Notification:

4.62 Reject cause code for GSM subscriber to UMTSnetwork (RCGTOU)


Q3 name: -









NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forGSM subscriber to UMTS network.


MXP

Notification:

4.63 Reject cause code for R97/98 terminal to GSMnetwork (RC97TOG)


Q3 name: -






NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forR97/98 terminal to GSM network.


MXP

Notification:

4.64 Reject cause code for subscriber count rejection(RCSCR)


Q3 name: -


DN99567618Issue 15-1 en


PLMN





NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forsubscriber count rejection.


MXP

Notification:

4.65 Reject cause code for UMTS subscriber to GSMnetwork (RCUTOG)


Q3 name: -







NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forUMTS subscriber to GSM network.


MXP

Notification:



4.66 Reject cause code for UMTS subscriber to UMTSnetwork (RCUTOU)


Q3 name: -







NO - Not used

MML default: NO

Description: With this parameter you can reject cause code forUMTS subscriber to UMTS network.


MXP

Notification:

4.67 The black list effect (BLE)


Q3 Name: -


Range: BLK... block action

AL... allow action

MML Default: BLK

Description: The parameter defines whether actions by black-listed mobile stations are allowed or not.


MXP

DN99567618Issue 15-1 en


PLMN



5 VLR

5.1 Index of the VLR (VLR)


Q3 Name: VLA ID

Modification: -

Range: 0..99

MML Default: -

Description: The parameter defines the index of the MSC/VLRobject in the database.

Related command(s): EJR

EJS

EJT

EJU

5.2 Location area code (LAC)


Q3 Name: locationAreaCode


Range: 1..65533

MML Default: -

Description: The parameter defines the location area codenumber.


DN99567618Issue 15-1 en


VLR

EJS

EJT

EJU



Q3 Name: mobileCountryCode


Range: Includes three digits

MML Default: -

Description: The parameter defines the unique country ofdomicile for the mobile subscriber.


EJS

EJT

EJU



Q3 Name: mobileNetworkCode


Range: Includes two or three digits

MML Default: -

Description: The parameter is used to distinguish mobilenetworks under one Mobile Country Code (MCC).The MNC identifies the Home GSM PLMN (HPLMN)of the mobile subscriber.


EJS

EJT



EJU

5.5 Nature of the VLR address (VNA)


Q3 Name: natureOfVlrAddress


Range: IN... international network

NA... national network

MML Default: IN

Description: The parameter defines the nature of the MSC/VLRaddress.


EJS

5.6 New VLR ISDN number (NISDN)


Q3 Name: -


Range: From 1 to 18 decimal digits.

MML Default: -

Description: The parameter defines the new MSC/VLR ISDNnumber.

Related command(s): EJS

5.7 Tunnelling of messages (TOM)


Q3 Name: tunnelingOfMessages


DN99567618Issue 15-1 en


VLR

Range: Y... tunnelling of messages in use

N... tunnelling of messages not in use

MML Default: N

Description: The parameter defines the tunnelling of messagesbeyond the Gs interface.


EJS

5.8 VLR ISDN number (VISDN)


Q3 Name: vlrIsdnNumber


Range: From 1 to 18 decimal digits.

MML Default: -

Description: The parameter defines the MSC/VLR ISDN number.


EJS

EJT

EJU

5.9 VLR signalling network code (VSNC)


Q3 Name: vlrSnc


Range: IN0... international network number 0

IN1... international network number 1

NA0... national network number 0

NA1... national network number 1

MML Default: NA0

Description: The parameter defines the MSC/VLR signallingnetwork code.




EJS

5.10 VLR signalling point code (VSPC)


Q3 Name: vlrSpc


Range: If the signalling network uses 14 bit point codes:

D'0-D'16383 (decimal number)

0-3FFF (hexadecimal number)

If the signalling network uses 24 bit point codes:

D'0-D'16777215 (decimal number)

0-FFFFFF (hexadecimal number)

MML Default: Value 0 means that the signalling point code is not inuse.

See also the notification field.

Description: The parameter defines the MSC/VLR signalling pointcode.


EJS

Notification: If a Signalling Point Code (SPC) is not given, theSPC to be used is derived from the VLR ISDNnumber (VISDN).

DN99567618Issue 15-1 en


VLR



6 LAC



Q3 Name: -



0x00.. All equivalent PLMN list indexes for locationarea are used.

0xFF.. No equivalent PLMN list index for locationarea is used.(EJL command)

0xFF.. Remove the equivalent PLMN list index forlocation area.(EJX command)

MML Default: 0x00

Description: The parameter defines the equivalent PLMN listindex for LAC.

Related command(s): EJL

EJX

Notification: The parameter is behind SGSN LAC based EPLMNlicence.

6.2 Location Area Code (LAC)


Q3 Name: -


DN99567618Issue 15-1 en


LAC

Range: 1..65533

MML Default: -

Description: The parameter defines the location area codenumber. The LAC parameter is a part of the LocationArea Identification (LAI), which consists of the mobilecountry code, the mobile network code, and thelocation area code.

Related command(s): EJA

EJE

EJL

EJR

EJS

EJT

EJU

EJQ

EJV

EJW

EJX



Q3 Name: -



MML Default: -



EJE

EJL

EJR

EJS

EJT

EJU



EJQ

EJV

EJW

EJX

6.4 Mobile Network Code (MNC)


Q3 Name: -



MML Default: -



EJE

EJL

EJR

EJS

EJT

EJU

EJQ

EJV

EJW

EJX

6.5 Modification type (MTYPE)


Q3 Name: -

DN99567618Issue 15-1 en


LAC


Range: With the EJQ command:

1..6

11..14

MML Default: -

Description: With the EJQ command:

Activate/deactivate the control for a home/visitorsubscriber group (on the location area level).

Activate/deactivate the control and association for ahome/visitor subscriber group (on the location arealevel).

Related command(s): EJQ

Notification: The range and meaning are not the same as withthe EJK command.

6.6 Output type (OTYPE)


Q3 Name: -


Range: 1...4

14,15

MML Default: -

Description: With this parameter you can define which controlledroaming parameters you want to output.

Related command(s): EJV

Notification: With the EJV command, when the value is 1...4:

The parameter outputs all the location areas wherecontrolled roaming is enabled/disabled for home/visitor subscriber groups.

With the EJV command, when the value is 14 or15:

The parameter outputs all allowed or non-allowedLAs and access rights by the home/visitorsubscriber group (GRNU) parameter.



7 CELL

7.1 BSSGP virtual connection identifier (BVCI)

3GPP Reference: 3GPP TS 48.016, General Packet Radio Service(GPRS); Base Station System (BSS) - Serving GPRSSupport Node (SGSN) Interface; Network Service,3GPP TS 48.018, General Packet Radio Service(GPRS); Base Station System (BSS) - Serving GPRSSupport Node (SGSN); BSS GPRS Protocol

Q3 Name: -

Modification: -

Range: 2..65535

MML Default: -

Description: The parameter defines the BSSGP virtual connectionidentifier of a cell.


7.2 Cell identity (CI)


Q3 Name: -

Modification: -

Range: 0..65535

MML Default: -

Description: The parameter defines the cell number.


DN99567618Issue 15-1 en


CELL



Q3 Name: -



0x00.. All equivalent PLMN list indexes.

0xFF..Equivalent PLMN list is not used in locationarea.

MML Default: 0xFF





Q3 Name: -


Range: 1..65533

MML Default: -

Description: The parameter defines the location area codenumber.


Notification: This parameter is always used with the mobilecountry code (MCC) and mobile network code (MNC)parameters.



Q3 Name: -




Range: Includes three digits

MML Default: -

Description: The parameter defines the unique country ofdomicile for the mobile subscriber.




Q3 Name: -


Range: Includes two or three digits

MML Default: -



7.7 Network service entity identifier (NSEI)


Q3 Name: nsEntityId

Modification: -

Range: 0..65535

MML Default: -

Description: The parameter identifies the Network Service Entity(NSE).


DN99567618Issue 15-1 en


CELL

7.8 Output cell parameters


Q3 Name: -

Modification: -

Range: Y ... cell parameters are output

N ... cell parameters are not output

MML Default: Y

Description: With this parameter, you can define if the cellparameters are output, or only the mobile countrycode (MCC), mobile network code (MNC), locationarea code (LAC), and routing area code (RAC)information is output.


7.9 PAPU unit index (PAPU)


Q3 Name: -


Range: 0..16

MML Default: -

Description: The parameter defines the index of the PAPU unit.


7.10 Routing area code (RAC)


Q3 Name: -

Modification: -

Range: 0..255

MML Default: -

Description: The parameter defines the routing area code.




DN99567618Issue 15-1 en


CELL



8 NSE

8.1 Connection type


Q3 Name: -


Range: DYN.. dynamic IP configuration parameters

STA.. static IP configuration parameters

FR.. frame relay configuration parameters

MML Default: -

Description: With this parameter you define the type of NetworkService Virtual Connection (NS-VC).

Related command(s): FWC

Notification: Static and dynamic IP configuration cannot be usedin the same Network Service Entity (NSE).

The parameter values DYN and STA are behind theSGSN Gb over Ip licence.

8.2 Connection type (CONN)


Q3 Name: -


Range: DYN.. Dynamic IP configuration parameters

FRGB.. Frame Relay and static IP configurationparameters

DN99567618Issue 15-1 en


NSE

MML Default: -

Description: With this parameter you can define the type ofconfiguration for all Network Service EntityIdentifiers (NSEI).

Related command(s): FWO

Notification: The parameter values DYN and FRGB are behindthe SGSN Gb over Ip licence.



Q3 Name: nsEntityId


Range: 0..65535

MML Default: -

Description: The parameter identifies the network service entity(NSE).


FWD

FWM

FWS

FWO

Notification: The value must be the same in the BSS and in theSGSN. The value is unique within the SGSN.

8.4 Network service entity special functionality(SFUNC)


Q3 Name: -




Range: 0.. special functionality is set off

1.. send BSSGP RESUME-ACK instead ofRESUME-NACK PDU

MML Default: 0

Description: The parameter identifies the NSE specialfunctionality.

Related command(s): FWM

FWO

Notification: If a resume PDU refers to an MS which is unknownin the SGSN, then a resume-nack PDU is returnedand the BSC shall instruct a MS to initiate the routingarea update procedure. However, some BSCs cannothandle the received RESUME-NACK PDU in BSSGPlayer.This parameter enables the SGSN to send theRESUME-ACK instead of RESUME-NACK PDU.



Q3 Name: PAPU ID


Range: 0..16

MML Default: -



FWD

FWE

FWG

FWK

FWM

FWO

FWS

DN99567618Issue 15-1 en


NSE



9 NS-VC

9.1 Administrative state


Q3 Name: adminState


Range: L ... lock the NS-VC

U ... unlock the NS-VC

MML Default: -

Description: With this parameter, you can lock or unlock anetwork service virtual connection.

Related command(s): FWS

Notification: The new NS-VC is in the 'blocked by user' (BL-US)state. You can change the state into 'workingexecuting' (WO-EX) with the FWS command.

9.2 Bearer channel identification (BCI)


Q3 Name: frBearerChannelId

Modification: -

Range: 0..1023

MML Default: -

DN99567618Issue 15-1 en


NS-VC

Description: The parameter identifies the bearer with a decimalnumber.


Notification: The parameter is given only for FR configuration.

9.3 Bearer channel name (BCN)


Q3 Name: frBearerChannelName

Modification: -

Range: Max 10 characters.

Allowed characters are: 'A'..'Z', '0'..'9', '-', '_', ' '.

MML Default: -

Description: The parameter identifies the bearer channel with aname.


Notification: The parameter is given only for FR configuration.

9.4 Committed information rate (CIR)


Q3 Name: committedInfoRate


Range: 16..1984 (kbit/s) with a 16 kbit step in ETSI

16..1536 (kbit/s) with a 16 kbit step in ANSI

MML Default: -

Description: The parameter defines the committed informationrate of an NS-VC.


Notification: The parameter is obligatory for FR configuration.



9.5 Data link connection identifier (DLCI)


Q3 Name: dataLinkConnectionId

Modification: -

Range: 16..991

MML Default: -

Description: The parameter defines the data link connectionidentifier.


Notification: The parameter is obligatory for FR configuration.

9.6 Endpoint PAPUs (PAPUS)


Q3 Name: -


Range: 0..16

MML Default: -

Description: With this parameter you can identify the PAPUs forwhich you want to create an endpoint. If you enter thisparameter without any parameter value, the systemshare capacity to the all PAPUs.


FWM

Notification: The parameter is given only for dynamic IPconfiguration if the PAPU group exists.

The parameter is behind the Large Routing AreaSupport, (LRAS) licence.

9.7 Load sharing mode (SMO)


Q3 Name: loadSharingMode

DN99567618Issue 15-1 en


NS-VC

Modification: -

Range: Y... load sharing is in use

N... load sharing is not in use

MML Default: Y

Description: The parameter defines the load sharing mode at theNS-VC level.


The parameter is given only for FR configuration.

9.8 Local UDP port number (LPN)


Q3 Name: localUdpPort

Modification: -

Range: 50000..65535

MML Default: -

Description: The parameter defines the local UDP port number.


Notification: The parameter is obligatory for IP configuration.



Q3 Name: nsEntityId


Range: 0..65535

MML Default: -

Description: The parameter identifies the network service entity(NSE).


FWD



FWM

FWS

FWO

Notification: The value must be the same in the BSS and in theSGSN. The value is unique within the SGSN.

9.10 Network service virtual connection identifier(NSVCI)


Q3 Name: nsVirtualConnectionId

Modification: -

Range: 0..65535

The value must be unique and the same both in theBSS and in the SGSN.

MML Default: -

Description: The parameter identifies the permanent virtual circuit.


FWD

FWM

FWO

FWS

Notification: The value must be the same in BSS and in SGSN,and it must be unique within the SGSN.

9.11 Network service virtual connection name (NAME)


Q3 Name: nsVirtualConnectionName

Modification: On- line

DN99567618Issue 15-1 en


NS-VC

Range: String of up to 10 characters.

Allowed characters are: 'A'..'Z','0'..'9', '-', '_',

The first character must be a letter.

MML Default: no name

Description: The parameter gives a name to the network servicevirtual connection.


FWD

FWM

FWO

FWS

Notification: By default, the NS-VCI parameter does not have aname.The parameter is given only for static IP orframe relay configuration.

9.12 New committed information rate (NEWCIR)


Q3 Name: committedInfoRate

Modification: The network service virtual connection must belocked.

Range: 16..1984 (kbit/s) with a 16 kbit step in ETSI

16..1536 (kbit/s) with a 16 kbit step in ANSI

MML Default: -

Description: The parameter defines the new committedinformation rate of the NS-VC.


Notification: The parameter can be modified only for FRconfiguration.

9.13 New configuration mode (NEWMODE)


Q3 Name: -




Range: 0 (auto-balanced configuration in use)

1 (operator configuration not in use)

MML Default: -

Description: With this parameter, you can define a newconfiguration mode. If autobalanced is in use, localweight values are set by system.


Notification: The parameter can be modified only for dynamic IPconfiguration.

The parameter is behind the SGSN Gb over IP licence.

9.14 New load sharing mode (NEWSMO)


Q3 Name: loadSharingMode


Range: Y... load sharing in use

N... load sharing not in use

MML Default: Y

Description: The parameter defines the new load sharing mode atthe NS-VC level.


Notification: The parameter can be modified only for FRconfiguration.

9.15 New local data weight (NEWLDW)


Q3 Name: -


Range: 0..255

MML Default: -

DN99567618Issue 15-1 en


NS-VC

Description: With this parameter, you can set a new local dataweight.


The parameter can be modified only for dynamic IPconfiguration.

The parameter is behind the SGSN Gb over IP licence.

9.16 New local sign weight (NEWLSW)


Q3 Name: -


Range: 0..255

MML Default: -

Description: With this parameter, you can give a new localsignalling weight.


The parameter can be modified only for dynamic IPconfiguration.

9.17 New local UDP port number (NEWLPNBR)


Q3 Name: -


Range: 50000..65535

MML Default: -

Description: The parameter defines the new local UDP portnumber.




Notification: Changes done to this parameter affect all NS-VCobjects under the same network service entity.

The parameter can be modified for static or dynamicIP configuration.

The parameter is behind the SGSN Gb over IPlicence.

9.18 New network service virtual connectionidentification name (NEWNAME)


Q3 Name: nsVirtualConnectionName


Range: String of max. 10 characters. Allowed characters are:'A'..'Z','0'..'9', '-', '_'.

The first character must be a letter. The name mustbe unique in the SGSN.

MML Default: -

Description: The parameter gives a new name to the networkservice virtual connection.


Notification: The parameter can be modified only for static IP orframe relay configuration.

9.19 New remote data weight (NEWRDW)


Q3 Name: dataWeight


Range: 0..255

MML Default: -

Description: The parameter defines the new remote data weight.The parameter can be modified only in static IPconfiguration.


DN99567618Issue 15-1 en


NS-VC

Notification: The parameter can be modified only for static IPconfiguration.

This is hidden parameter.

9.20 New remote IP endpoint (NEWRIPEP)


Q3 Name: ipAddress


Range: For IPv4: the values range from 1.0.0.0 to255.255.255.252.

For IPv6: 39 numeric and special characters. Theallowed characters are 'A'...'F', ':', and '0'...'9'.

MML Default: -

Description: The parameter defines the new remote IP endpoint.




9.21 New remote sign weight (NEWRSW)


Q3 Name: signWeight


Range: 0..255

MML Default: -

Description: The parameter defines the new remote signallingweight.






9.22 New remote UDP port number (NEWRPNBR)


Q3 Name: udpPort


Range: 0..65535

MML Default: -

Description: The parameter defines the new remote UDP portnumber.


Notification: The parameter is given only for static IPconfiguration.




Q3 Name: -


Range: 0..16

MML Default: -



FWD

FWE

FWG

FWK

FWM

FWO

FWS

Notification:

DN99567618Issue 15-1 en


NS-VC

9.24 Remote data weight (RDW)


Q3 Name: dataWeight


Range: 0..255

MML Default: -

Description: The parameter defines the remote data weight.


Notification: The parameter is obligatory for static IP configuration.

9.25 Remote IP endpoint (RIPE)


Q3 Name: ipAddress


Range: For IPv4: the values range from 1.0.0.0 to255.255.255.252.

For IPv6: 39 numeric and special characters. Theallowed characters are 'A'...'F', ':', and '0'...'9'.

MML Default: -

Description: The parameter defines the remote IP endpoint.


Notification: The parameter is obligatory for static IP configuration.

9.26 Remote sign weight (RSW)


Q3 Name: signWeight




Range: 0..255

MML Default: -

Description: The parameter defines the remote sign weight.


Notification: The parameter is obligatory for static IPconfiguration.

9.27 Remote UDP port number (RPNBR)


Q3 Name: udpPort


Range: 0..65535

MML Default: -

Description: The parameter defines the remote UDP port number.


Notification: The parameter is obligatory for static IPconfiguration.

DN99567618Issue 15-1 en


NS-VC



10 Home/Visitor subscriber group

10.1 Access rights of subscriber group (ACCR)


Q3 Name: -


Range: 1... 2G roaming allowed

2... 3G roaming allowed

3... 2G and 3G roaming allowed

MML Default:

Description: The parameter defines the access rights of asubscriber group.

Related command(s): EJK

10.2 Modification type (MTYPE)


Q3 Name: -


Range: ADD... add a subscriber group

DEL... delete a subscriber group

CHANGE... change a subscriber group

MML Default:

Description: The parameter defines the modification type.


DN99567618Issue 15-1 en


Home/Visitor subscriber group

Notification: The range and meaning are not the same as withthe EJQ command.

With the EJK command:

If you enter DEL (delete) together with thesubscriber group identity number (GRNU) parameter,the subscriber group with the entered GRNU isdeleted.

If you enter DEL, but not GRNU, the whole accesslist is deleted.



Q3 Name: -


Range: 10..13

MML Default:

Description: The parameter outputs home/visitor access list(s)with subscriber group(s) and their access rights bythe access list number (ALNU) / access list name(ALNA) or subscriber group identity number (GRNU)parameters.


10.4 Subscriber group identity number (GRNU)


Q3 Name: -


Range: 0..9 999 999 999 999 999

Maximum 16-digit decimal number.

MML Default:

Description: The parameter defines the subscriber group identitynumber.


EJV



Notification: With the EJK command:

If you enter this parameter together with DEL(delete), the subscriber group with the entered GRNUis deleted.

If you enter DEL, but not GRNU, the whole accesslist is deleted.

10.5 Subscriber group type (STYPE)


Q3 Name: -


Range: HOME... home subscriber group

VIS... visitor subscriber group

MML Default:

Description: The parameter defines the subscriber group type.


10.6 User rights to roam (URT)


Q3 Name: -


Range: 0... no rights



3... 2G and 3G roaming allowed

MML Default:

Description: The parameter defines the subscriber group accessrights.


DN99567618Issue 15-1 en


Home/Visitor subscriber group



11 Home/Visitor access list

11.1 Access list name (ALNA)


Q3 Name: -


Range: Max. 15 characters

MML Default:

Description: The parameter defines the access list name.


EJQ

EJV


If you enter 'add', you must enter both this parameterand the access list number (ALNU) parameter.Otherwise either ALNA or ALNU can be entered.

11.2 Access list number (ALNU)


Q3 Name: -


Range: 0..199

MML Default:

Description: The parameter defines the access list number.


DN99567618Issue 15-1 en


Home/Visitor access list

EJQ

EJV


If you enter 'add', you must enter both this parameterand the access list name (ALNA) parameter.Otherwise either ALNA or ALNU can be entered.



Q3 Name: -


Range: 1..65533

MML Default: -


Related command(s): EJQ

EJV



Q3 Name: -


Range: A decimal number with three digits.

MML Default:


EJQ





3GPP Reference: 3GPP TS 23.003, Numbering, addressing andidentificationf

Q3 Name: -


Range: A decimal number with either two or three digits.

MML Default:


EJQ




Q3 Name: -


Range: 5..13

MML Default:

Description: The parameter outputs home/visitor access lists. Youcan define by which parameter (LAI, GRNU, ALNA,or ALNU) you want to list the access lists.


DN99567618Issue 15-1 en


Home/Visitor access list



12 PAPU group

12.1 DL forwarding activated (DL)


Q3 Name: dlForwardingMode


Range: Y... DL forwarding in use

N... DL forwarding not in use

MML Default: N in configuration model 1

Y in configuration models 2 and 3

Description: The parameter used to define whether DL forwardingwas in use or not. Since DL forwarding is currentlyalways active in every PAPU group model, thisparameter has no effect any more.

Related command(s): FWF

Notification: This parameter has been removed from the Gbinterface, but it can still be displayed during the MMLsession. The whole parameter will be removed inlater releases.

12.2 Foreign and random TLLI UL forwarding activated(UL)


Q3 Name: foreignAndRandomTlliULForwardingMode


Range: Y... foreign and random TLLI UL forwarding in use

DN99567618Issue 15-1 en


PAPU group

N... foreign and random TLLI UL forwarding not inuse

MML Default: N in configuration model 1

Y in configuration models 2 and 3

Description: The parameter defines whether foreign and randomTLLI UL forwarding is in use or not.


Notification: The default value of the parameter depends on theconfiguration model set in the parameter PAPUgroup configuration model (PGM).

12.3 NSVC PAPU cell control (NPCC)


Q3 Name: nsvcPapuCellControl


Range: Y... NSVC PAPU for cells in use

N... NSVC PAPU for cells not in use

MML Default: -

Description: The parameter identifes if the NSVC PAPU is usedfor cells.


FWG

Notification: The parameter is behind the LRAS Enhancementslicence.

12.4 PAPU group action


Q3 Name: -

Modification: -

Range: ADD ... Add PAPU to the PAPU group

REM ... Remove PAPU from the PAPU group

MML Default: -



Description: With this parameter, you can add a PAPU to a PAPUgroup, or remove a PAPU from a PAPU group.

Related command(s): FWE

12.5 PAPU group configuration model (PGM)


Q3 Name: papuGroupConfigurationModel


Range: 1... Model 1 – distributed RA/NSE/CELL

2... Model 2 – distributed RA/NSE

3... Model 3 – distributed RA, load sharing in use

MML Default: -

Description: The parameter defines the PAPU group configurationmodel.


FWG

12.6 PAPU group identifier (PGI)


Q3 Name: PAPG ID


Range: 1..255

MML Default: -

Description: The parameter defines the PAPU group identifier.


FWE

FWF

FWG

FWI

DN99567618Issue 15-1 en


PAPU group

12.7 PAPU group name (PGN)


Q3 Name: nwName


Range: String of up to 15 characters

The allowed characters are: 'A'..'Z', '0'..'9', '-', '_', ' '

MML Default: -

Description: The parameter defines the PAPU group name.

Related command(s): FWG



Q3 Name: papuUnitIndex


Range: 0..16

MML Default: -

Description: The parameter defines the PAPU unit index.


FWD

FWG

FWI

FWK

FWM

FWS

FWO

Notification: If you give this parameter without any parametervalue, all PAPUs are defined.



13 PAPU params

13.1 Blocking for maintenance (BLO)


Q3 Name: -


Range: Y... PAPU has been blocked for maintenance

N... PAPU has been unblocked for normal use

MML Default: N

Description: With this parameter you can set the PAPU to theblocked state or unblock the PAPU for normal use.

Related command(s): FWB

Notification: It is possible to block a PAPU for maintenance if theoffloading process has not been activated in thePAPU.

Only one PAPU in the PAPU group can be blocked.You can unblock a PAPU for normal use if massdetach is not active.

13.2 Mass detach (MD)


Q3 Name: -


Range: START... starts mass detach

CANCEL... cancels mass detach

MML Default:

DN99567618Issue 15-1 en


PAPU params

Description: With this parameter you can start or cancel theexecution of mass detach in the PAPU.


Notification: You can start mass detach if the PAPU has beenblocked for maintenance.

13.3 Multipoint offload phase (PHASE)


Q3 Name: -


Range: 0... cancels offloading

1... activates offloading phase 1



AUTO... starts automated offloading

MML Default:

Description: With this parameter you can activate the phase ofthe offloading process manually or start theautomated offloading process. With this parameteryou can also cancel the offloading process.


Notification: The offloading takes place in three phases. It ispossible to activate the second phase of theoffloading procedure either manually or use theautomated process. If the offloading process is donemanually, phase 2 can be activated immediately afterphase 1. If the automated process is used, eachphase is activated automatically after two periodiclocation updates have expired. You can use the FWIcommand to view the status of the offloadingprocess.



Q3 Name: papuUnitIndex




Range: 0..16

MML Default: -

Description: The parameter defines the PAPU unit index.


FWI

Notification: If you give this parameter without any parametervalue, all PAPUs are defined.

13.5 Radio access type (RAT)


Q3 Name: -


Range: GB... Gb interface

IU... Iu interface

ALL... All interfaces

MML Default:

Description: This parameter defines for which access type themass detach or (automated or manual) Multipointoffloading procedure is performed.


Notification:

DN99567618Issue 15-1 en


PAPU params



14 HT-CGI

14.1 Cell identity (CI)


Q3 Name: cellId


Range: 0..65535

MML Default: -

Description: The parameter defines the cell number.

Related command(s): EJW

14.2 Location Area Code (LAC)


Q3 Name: locationAreaIdLAC


Range: 1..65533

MML Default: -



DN99567618Issue 15-1 en


HT-CGI



Q3 Name: locationAreaIdMCC



MML Default: -



14.4 Mobile Network Code (MNC)


Q3 Name: locationAreaIdMNC



MML Default: -



14.5 PAPU index (PAPU)


Q3 Name: papuId

Modification: -

Range: 0..16

MML Default: -



Description: The parameter defines the index of a PAPU, towhich the high traffic cell is located.


Notification: By default, you do not give the PAPU index (PAPU)parameter, and the related PAPU is chosen bysystem.

Before using the EJW command, the PAPU groupmust be created with the FWG command.

DN99567618Issue 15-1 en


HT-CGI



15 APN

15.1 Access Point Name (APN)

3GPP Reference: 3GPP TS 23.003 Numbering, addressing andidentification

Q3 Name: -


Range: The length of the identifier ranges from 2 to 63alphanumeric and special characters. The allowedcharacters are 'A' .. 'Z', 'a' .. 'z', '0' .. '9', and '' .

MML Default: —

Description: With this parameter, you can define the externalnetwork to which the SGSN is connected.

Related command(s): E5C

E5D

E5I

Notification: In the GPRS backbone, the APN is a reference tothe GGSN to be used. The APN-string cannot endwith '.gprs' and cannot start with 'RAC', 'LAC', or'SGSN'. The string is a set of labels separated bydots, for example, 'company.com'. The APN muststart with an alphanumeric character.

15.2 Usage of command (USE)


Q3 Name: -


DN99567618Issue 15-1 en


APN

Range: ADP (APN Dedicated Prepaid)

HGGSN (Home GGSN Solution)

DT (Direct Tunnel)

MML Default: ADP (APN Dedicated Prepaid)

Description: This parameter defines to which feature the createcommand is used.


E5D

E5I



16 RNC

16.1 Global title address (DIG)


Q3 name: -


Range: Decimal string of 1 to 18 digits

MML default:

Description: This parameter defines the global title address ofan RNC under the SGSN.


E6M

Notification:

16.2 Information type (TYPE)


Q3 name: -


Range: PAR - parameters

TIM - timers

REM - remove a parameter set

MML default:

Description: With this parameter you can define the informationtype you wish to modify.

Related command(s): E6N

DN99567618Issue 15-1 en


RNC

Notification: The information type is obligatory if the existingparameter set is modified or deleted.

16.3 IP interface name (IPNAME)


Q3 name: -


Range: The name of IP over ATM interface begins with 'AA'and continues with decimal numbers 0...199.

MML default:

Description: This parameter defines the unique name of IPinterface.

Related command(s): E6G

Notification: To check the names of existing IP interfaces,output the current interfaces with the QRIcommand.



Q3 Name: -


Range: Allowed value range is from 0 to 5 or FF.

0. All equivalent PLMN list indexes for location areaare used.

FF. No equivalent PLMN list index for location areais used.

MML Default: FF

Description: The parameter defines the equivalent PLMN listindex for LAC.

Related command(s): E6L

E6Q

MXN






Q3 Name: -



MML Default: -

Description: This parameter defines the mobile country code of anRNC.


E6D

E6L

E6M

E6I

E6Q

E6R

E6S

E6G

Notification: You must give both MOBILE_COUNTRY_CODE andMOBILE_NETWORK_CODE parameters if the SGSNPLMN is not used.



Q3 Name: -



MML Default: -

Description: This parameter defines the mobile network code ofan RNC.

DN99567618Issue 15-1 en


RNC


E6D

E6L

E6M

E6I

E6Q

E6R

E6S

E6G

Notification: You must give both MOBILE_COUNTRY_CODE andMOBILE_NETWORK_CODE parameters if the SGSNPLMN is not used.

16.7 Mobile country code of LA (LAMCC)


Q3 name: -


Range: A decimal string with 3 digits.

MML default:

Description: This parameter defines the mobile country code ofthe location area.


E6M

Notification:

16.8 Mobile network code of LA (LAMNC)


Q3 name: -


Range: A decimal string with 2 or 3 digits.

MML default:



Description: This parameter defines the mobile network code ofthe location area.


E6M

Notification:

16.9 Network indicator (NI)


Q3 name: -


Range: NI - IN0 international network

IN1 - reserved for international use

NA0 - national network

NA1- reserved for national use

MML default:

Description: This parameter indicates the value that representsthe type of network where the RNC is located. Theavailable values depend on the systemconfiguration.


E6M

Notification:

16.10 New radio network controller name (NNAME)


Q3 name: -


Range: Text string of 1 to 10 characters.

MML default:

Description: This parameter renames the RNC.

Related command(s): E6M

DN99567618Issue 15-1 en


RNC

Notification:

16.11 PAPU group identifier (PGI)


Q3 Name: PAPG ID


Range: 1..255

MML Default: -

Description: This parameter defines the packet processing unit(PAPU) group identifier.


E6M

Notification:



Q3 Name: PAPU ID


Range: 0..16

MML Default: -



E6G

E6M

16.13 Radio network controller identification (RNCID)




Q3 name: -


Range: 1...4095

MML default:

Description: The parameter defines the number of an RNCunder the SGSN.


E6D

E6G

E6I

E6M

E6R

E6S

Notification:

16.14 Radio network controller name (RNCNAME)


Q3 name: -


Range: Text string (1 to 10 characters)

MML default:

Description: The parameter defines the name of an RNC underthe SGSN.


E6D

E6G

E6I

E6M

E6R

E6S

Notification:

DN99567618Issue 15-1 en


RNC

16.15 Radio network controller parameter set (PSET)


Q3 name: -


Range: 0...10

MML default:

Description: This parameter defines the RNC parameter andtimer set.


E6J

E6M

E6N

Notification: Parameter set 0 is a predefined default parameterset which is not modifiable.

16.16 Radio network controller parameter set name(PNAME)


Q3 name: -


Range: A text string of 1 to 10 characters

MML default:

Description: This parameter defines the name of the RNCparameter and timer set.

Related command(s): E6J

E6N

Notification: When creating a new parameter set, parametersPSET and PNAME must both be given.



16.17 Radio network controller state (STATE)


Q3 name: -


Range: L - locked

B - blocked

U - unlocked

MML default:

Description: The parameter indicates the administrative state ofan RNC.

Related command(s): E6S

Notification:

16.18 Relation type (RT)


Q3 name: -


Range: NONE - Outputs all RNCs without RAI list.

ALL - Outputs all RNCs with RAI list.

RNCR - Outputs only traditional RNCs with RAI list.

RNC - Outputs only traditional RNCs without RAIlist

IHSPAR - Outputs only I-HSPA NodeBs with RAIlist

IHSPA - Outputs only I-HSPA NodeBs without RAIlist

MML default: NONE

Description: With this parameter you can choose the type ofinformation you wish to view.

Related command(s): E6I

E6L

Notification:

DN99567618Issue 15-1 en


RNC

16.19 RNC connect action


Q3 name: -


Range: ADD - connect RNC to IPoA link

INT - interrogate RNC and IPoA link connection

REM - disconnect RNC to IPoA link

MML default:

Description: This parameter defines the RNC connection toIPoA link action.

Related command(s): E6G

16.20 Routing area code list (RACL)


Q3 name: -


Range: 0...255

MML default:

Description: This parameter defines the routing areas which areattached to the location area.


Notification: You can give at the most 10 routing area codes byusing the '&' character. If 10 routing areas are notenough, you can add more with the E6M command.

16.21 Routing area code list add (RACLA)


Q3 name: -


Range: 0...255



MML default:

Description: This parameter defines the routing areas which areadded to the location area.


Notification: A maximum of 10 routing area codes in onecommand can be given by using the '&' character.

16.22 Routing area code list remove (RACLR)


Q3 name: -


Range: 0...255

MML default:

Description: This parameter defines the routing areas to beremoved from the location area.


Notification: A maximum of 10 routing area codes can be givenin one command by using the '&' character.

16.23 Signalling point code (SPC)


Q3 name: -


Range: 1...3FFF

1... FFFFFF (in a hexadecimal format)

MML default:

Description: The parameter indicates the signalling point code ofthe network where the RNC is located.


E6M

DN99567618Issue 15-1 en


RNC

Notification: The value depends on the type of network (14 bitor 24 bit) selected, that is, the NI parameter mustbe given first.

16.24 Type of address (TOA)


Q3 name: -


Range: GT - Global title address

DPC - Destination point code

MML default: GT

Description: This parameter defines the type of address.


E6M

Notification: If the GT is given, the DIG parameter is obligatoryin the third block. If the DPC is given, the NI andthe SPC parameters are obligatory in the thirdblock.

16.25 Type of RNC (TYPE)


Q3 name: -


Range: RNC - radio network controller (in traditionalUTRAN architecture)

IHSPA - I-HSPA NodeB (in flat UTRANarchitecture)

MML default: RNC

Description: This parameter defines the radio network controllertype.


E6M

Notification:



DN99567618Issue 15-1 en


RNC



17 IP

17.1 Application identifier (APP)


Q3 Name: -


Range: GN - Gn IP control and user plane between SGSNand GGSN

PGN - Gn IP control and user plane from PAPU

IUU - Iu user plane

GB - Gb interface between BSC and SGSN

LIB - Lawful Interception user data

LRAS - Large RA forwarding

GA - Ga interface

RTT - Real time traffic monitoring interface betweenSGSN and monitoring device

DUPP - Control plane between SGSN and UNC-CSfor Distributed Architecture UMA.

DUPPS - User plane between SGSN and SGW forDistributed Architecture UMA.

SIMO - Signalling Monitoring for NetSIMO.

MML Default:

Description: The parameter defines the identifier of an applicationrelated to SGSN.

Related command(s): KAC

KAD

Notification: Parameters DUPP and DUPPS are behind theDistributed UMA Support licence.

DN99567618Issue 15-1 en


IP

Parameter LRAS is behind the Large Routing AreaSupport (LRAS) licence.

17.2 Index of source IP index for application (INDEX)


Q3 Name: -


Range: Decimal number (depends on the systemconfiguration)

MML Default:

Description: The index of source IP address for application inSGSN.

Related command(s):

Notification: Either parameter ADDRESS or INDEX must begiven in command, not both.


17.3 Source IP address for application (ADDRESS)


Q3 Name: -


Range: IP address in quotation marks.

MML Default:

Description: The source IP address for application in SGSN.


Notification: Either parameter ADDRESS or INDEX must begiven in command, or both.



17.4 Source IP address version (VER)


Q3 name: -


Range: IPV4 - IPv4 address will be deleted.

IPV6 - IPv6 address will be deleted.

MML default:

Description: This parameter defines the IP address version tobe deleted.

Related command(s): KAD

Notification: The parameter is obligatory.

If the value of the APP parameter is DUP orDUPSS, then only IPv4 address is allowed.

17.5 Unit index


Q3 name: -


Range:

MML default:

Description: This parameter specifies the index of the computerunit in which the source IP addresses reside.


KAD

KAI

Notification: This parameter is obligatory in cases when the unittype is either SMMU or PAPU, but the parameter isnot allowed in cases when the unit type is eitherOMU or MCHU.

DN99567618Issue 15-1 en


IP

17.6 Unit type


Q3 name: -


Range: MCHU

PAPU

OMU

SMMU

MML default:

Description: This parameter specifies the type of the computerunit in which the source IP addresses reside.


KAD

KAI

Notification: The parameter is obligatory.



18 Related MML command documentation

18.1 GPRS Network Handling (EJ) commands

The commands of the GPRS Network Handling (EJ) command group areused for handling the SGSN and MSC/VLR to LA association parametersin a database located in the SGSN.

The commands in this command group are as follows:

EJA Create Location Area

EJE Delete Location Area

EJF Modify SGSN Parameters

EJH Output SGSN Parameters

EJK Modify Controlled Roaming Subscriber Group

EJL Output Network Configuration

EJQ Modify LA Access List Associations

EJR Create MSC/VLR to LA Association

EJS Delete MSC/VLR to LA Association

EJT Modify MSC/VLR to LA Association

EJU Output MSC/VLR to LA Association Parameters

EJV Output Controlled Roaming Configuration Parameters

EJW Control Distribution of Cells

EJX Modify Location Area Parameters

DN99567618Issue 15-1 en


Related MML command documentation

18.2 GPRS Mobility and Session Handling in SGSN (E5)commands

The commands of the GPRS Mobility and Session Handling in SGSN (E5)are used for handling the GPRS mobility and session parameters in theSGSN.

E5C Create List of Selective APN

E5D Delete List of Selective APN

E5I Interrogate List of Selective APN

18.3 Radio Network Controller Parameter Handling inSGSN (E6) commands

The commands of the Radio Network Controller Parameter Handling inSGSN (E6) are used for managing the radio network controller (RNC)parameters in the SGSN.

E6C Create RNC to Radio Network

E6D Delete RNC from Radio Network

E6G Control Connection RNC to IPoA Link

E6I Interrogate RNC in Radio Network

E6J Interrogate RNC Parameter Set Information

E6L Interrogate Routing Area Relation

E6M Modify RNC in Radio Network

E6N Modify RNC Parameter Set Information

E6Q Modify Location Area Parameters

E6R Restart RNC in Radio Network

E6S Change RNC State in Radio Network



18.4 GPRS NS Layer Handling (FW) commands

The commands of the GPRS NS Layer Handling (FW) command group areused for handling the network service virtual connection parameters andPAPU group parameters in a database located in the SGSN.


FWB Prepare For Maintenance

FWC Create Network Service Virtual Connection

FWD Delete Network Service Virtual Connection

FWE Modify PAPU Configuration in PAPU Group

FWF Modify PAPU Group Parameters

FWG Create PAPU Group

FWI Interrogate PAPU Group and PAPU Configuration

FWJ Modify NRI Configuration

FWK Interrogate NRI Configuration

FWM Modify Network Service Virtual Connection Data

FWO Output Network Service Virtual Connection Data

FWS Change State of Network Service Virtual Connection

18.5 Application Configuration Handling (KA)commands

The commands of the Application Configuration Handling (KA) commandgroup are used for handling the application configuration in SGSN.

KAC Create Source IP Address Association

KAD Delete Source IP Address Association

KAI Interrogate Source IP Address Association

DN99567618Issue 15-1 en


Related MML command documentation

18.6 PLMN Parameter Handling (MX) commands

The commands of the PLMN Parameter Handling (MX) command groupare used for handling the PLMN-level parameters in a database located inthe SGSN.


MXA Add PLMN

MXD Delete PLMN

MXN Modify PLMN Parameters

MXP Output PLMN Parameters



Documents

PARAMETER DICT