OPERATING MANUAL AND USER GUIDEOPERATING MANUAL AND USER GUIDE 1 IMPORTANT WARNINGS & SAFETY INSTRUCTIONS 1. Read these instructions 2. Follow all instructions 3. Keep these instructions

www.wharfedalepro.com

Titan™Titan™ 8 Passive Titan™ 12 Passive Titan™ 15 PassiveTitan™ 8 Active MKII Titan™ 12D Titan™ 15D Titan™ Sub A12 Titan™ Sub A15

OPERATING MANUAL AND USER GUIDE


1

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS1. Readtheseinstructions2. Followallinstructions3. Keeptheseinstructions4. Heedallwarnings5. Donotusethisapparatusnearwater6. Cleanonlywithdrycloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.8. Donot install nearanyheatsourcessuchas radiators,heat registers, stoves,orother

apparatus (including amplifiers) that produce heat.9. Donotdefeatthesafetypurposeofthepolarisedorgroundingplug.Apolarisedplughastwo

bladeswithonewiderthantheother.Agroundingplughastwobladesandathirdgroundingprong.Thewidebladeorthethirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnot fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protectthepowercordfrombeingwalkedonorpinchedparticularlyattheplugs,conveniencereceptacles,andatthepointwheretheyexitfromtheapparatus.

11. Only use attachments/accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with

theapparatus.Whenacartorrackisused,usecautionwhenmovingthecartandapparatuscombinationtoavoidinjuryfromtip-over.

13. Unplugtheapparatusduringlightningstormsorwhenunusedforlongperiodsoftime.14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been

damaged inanyway includingbutnot limited topowersupplycordorplugdamage, liquidingress,foreignobjectsinthechassis,exposuretorain/moistureorimpactdamage.Inadditiontheunitmustbeservicedwhenyouexperienceanyabnormaloperation.

15. CAUTION:Theseservicing instructionsare forusebyqualifiedservicepersonnelonly.Toreduce the riskofelectricshock,donotattempt toperformanyservicingother than thatcontained in the operating instructions unless you are qualified to do so. In addition opening the casingwillresultinyourwarrantybecomingnullandvoid.

16. Do not install this apparatus in a confined space such as a book case or similar unit. Good ventilationshouldbemaintainedaroundtheapparatusandanyvents,air-inletsorfansshouldnotbeobstructedbyobjectssuchaspaper,table-cloths,curtainsetc.

17. WARNING: To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture. The apparatus should not be exposed to dripping or splashing and objects filled with liquids,suchasvases,shouldnotbeplacedontheapparatus.

18. WARNING: The mains plug/appliance coupler is used as a disconnect device, the disconnect deviceshallremainreadilyoperable.

Titan™ Series

2

19. - This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the usertothepresenceofnon-insulated“dangerousvoltage”withintheproduct’senclosurethatmay be of sufficient magnitude to constitute a risk of electric shock.

- Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

-Theexclamationpointwithinanequilateral triangle is intended toalert theuser to thepresenceof importantoperatingandmaintenanceinstructions inthe literatureaccompanyingtheappliance.

20. (Protective earthing terminal) The apparatus should be connected to a mains socket outlet withaprotectiveearthingconnection.

21. CorrectDisposalof thisproduct.Thismarking indicates that thisproductshouldnotbedisposedwithotherhouseholdwastes throughout theEU.Topreventpossibleharmto theenvironmentorhumanhealth fromuncontrolledwastedisposal, recycle it responsibly topromotethesustainablereuseofmaterialresources.Toreturnyouruseddevice,pleaseuselocalreturnandcollectionsystemsorcontact theretailerwheretheproductwaspurchased.Theycantakethisproductforsafeenvironmentallyfriendlyrecycling.

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR


3

TABLE OF CONTENTS

1..........................................Important Warnings & Safety Instructions 2..........................................Important Safety Information Powered Products 4..........................................Introduction / About the Titan™ Series 4..........................................Titanseriesoverview5..........................................Features6..........................................Qubit 7..........................................Setting up / Speaker Placement 7..........................................Connections/Wiring-Passive8..........................................Rear Panel Layout - Passive 8..........................................ConnectionDiagram-Passive11..........................................Rear Panel Layout - Active14..........................................ConnectionDiagram-Active15..........................................Rear Panel Layout - Sub A1216..........................................Connection Diagram - Sub A1218..........................................Rear Panel Layout - Sub A1519..........................................Connection Diagram - Sub A15 21..........................................Specifications - Titan™ Passive22..........................................Specifications - Titan™ Active24..........................................Specifications - Titan™ Subwoofers25..........................................DimensionalDrawings-Titan™8/1226..........................................DimensionalDrawings-Titan™15/8AMKII27..........................................DimensionalDrawings-Titan™12D/15D28..........................................Dimensional Drawings - Titan™ Sub A12 / A1529…………………………..…Warranty

Titan™ Series

4

Wharfedale Pro Titan™ Series is the result of many years of experience in the use, design and manufacturingofprofessional loudspeakerproducts.We takegreatpride inengineeringandbuildingeveryWharfedaleProloudspeakerandwishtothankyouforentrustinguswithyoursound.

From the time Gilbert Briggs built his first loudspeaker in 1932, to the present, Wharfedale Loudspeakers have maintained the same standard of quality in components, workmanship and performance.Wharfedaleareoneofthefewpresentdaymanufacturersthatdesign,engineerandbuildallofourowntransducers.

Pleasetakeafewminutestoreadthismanualcompletelyinordertoensurethatyougetthemostout of your Titan™ Series Loudspeaker system.

INTRODUCTION

TITAN™ SERIES OVERVIEW

The Titan Series are powerful, accurate, high quality loudspeaker systems with low distortion thataredesignedtodeliveroustandingperformanceatacosteffectivepricepoint.AnEllipticalWave Guide (EWG) is perfectly matched to the custom designed HF drivers and provides smooth dispersioninboththehorizontalandverticalplanes.

The road tough,gas-assist injectionmouldedpolypropyleneenclosuresareultra lightweightand include rubberisedhandlesandcablemanagement tomakeTitan themostuser-friendlyportable speaker on the market. Threaded rigging points mean that Titan is equally suited to flown applications;acomprehensiverangeofWharfedaleProwallmountingoptionsarealsoavailableasoptionalextras.

Active models feature rear panel power LED’s and a throat mounted LED to make you aware of AC power supply from both the front and rear of the unit. Active models also feature a horn LED defeat switch for less obtrusive aesthetics in applications such as conferencing and A/V presentations. The BRO™ (Bass Response Optimizer) circuit on the 12D and 15D models helps counteract loss of bass at low levels, similar to a loudness switch on home HiFi amplifiers. In addition our "D" models feature Qubit™ 24-bit 192kHz DSP Processing.


5

FEATURES

♦2-wayfullrangeloudspeakers

♦ Low distortion, high power moisture proof woofers

♦HFcompressiondrivers

♦ 90° x 60° Elliptical Wave Guide (EWG)

♦DTF™DynamicThermalFilamentHFprotection

♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures

♦Ergonomicrubberisedhandles

♦ Integral lockable 35mm (1⅜”) pole mount socket

♦M6/M8riggingpoints

♦ Speakon™ and ¼” jack inputs

Titan Passive

♦ Bi-amplified full range loudspeakers

♦ Low distortion, high power moisture proof woofers

♦HFcompressiondrivers

♦ Qubit™ 24-bit 192kHz DSP processing

♦ Independent LF & HF adaptive dynamics and signal limiting

♦ Per channel volume controls (Master only on 8A MKII)

♦ 2 Band EQ

♦ 90° x 60° elliptical Wave Guide (EWG)

♦ BRO™ Bass Response Optimizer (12D & 15D only)

♦ Horn LED defeat switch

♦ Balanced XLR output for parallel wiring

♦ XLR / ¼” jack combo inputs

♦Mic/linelevelinputselector

♦ 2 mixable inputs (12D & 15D only)

♦ Stereo RCA inputs (12D & 15D only)

♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures

♦Ergonomicrubberizedhandles

♦ Integral lockable 35mm (1⅜”) pole mount socket

♦M6/M8riggingpoints

♦IECACreceptacle

Titan Active

Titan™ Series

6

♦ Low distortion, high power woofers

♦ 2x balanced XLR HPF outputs

♦ 2x summed XLR / ¼” jack combo inputs

♦ Built in signal limiting

♦ Adjustable crossover frequency (SUB 12A only)

♦-∞to +6dB trim control

♦0°/180°switch

♦Ergonomichandles

♦Polemountsocket

♦IECACreceptacle

Subwoofer

Qubit brings the power and precision of 24-bit 192kHz DSP processing to the next generation of WharfedaleProProducts.

With advanced multi-band dynamic processing and filtering Qubit helps fine tune your system to sound natural and open. Qubit processing optimises the loudspeaker to provide smooth digital crossoverpoints thatareperfectlyaligned.Protection isoffered in the formof true independentadaptive LF and HF signal limiting that helps protect against thermal damage and driver over excursion.

Qubit has an extended frequency response that goes way beyond the capabilities of our hearing, providinganextendedphaseresponsethatremains linear throughoutournaturalhearingrange.A Qubit equipped system can reproduce exceptionally natural and accurate transients due to its phasecharacteristicsandperfecttimealignment.

QUBIT™


7

SETTING UP

1. Ensure the speakers power switch is in the off position (Active models only)2. Set the level controls to minimum (Fully anticlockwise) (Active models only)3. Set the EQ controls to 0dB (Active models only)4. Select mic/line input (Active models only)5.Connectallsignalcables6. Connect the power cable (Active models only)7. Switch on source equipment, ensuring that the master level is at minimum8. Switch on the Titan Loudspeaker (Active models only)9. Raise the level control on the Titan (Active models only) or external amplifier10. If the limit LED illuminates lower the level control, if more level is required you will need more speakers. Occasional flashes are acceptable. (Active models only)11. When powering down your system ensure that the level control (Active models only) has been loweredtominimumbeforeswitchingoffthepower

ThewellbehaveddispersioncharacteristicsoftheTitanseriesmakespeakerplacementquickandsimple.

AswithallfullrangeloudspeakersitisrecommendedtoplaceaTitanabovetheheadleveloftheaudience,as thehumanbodycanabsorbahugeamountofhighfrequencyenergy.Placingtheloudspeakerenclosurehigherupalsohelpsimprovecoverageformoreevenlevelsoveragreateraudiencearea.

Tripodspeakerstands,polemounts,WallbracketsandrigginghardwarecanbeusedtoelevatetheTitanloudspeaker.Alwaysensurethatanyaccessoriesthatareusedarecapableofsafelyelevatingtheloudspeakerasincorrectriggingcanbedangerousandevenfatal.Pleaserefertotheimportantsafetywarningssectionformoreguidelinesonriggingandsuspending.

Alwaysplaceyourmicrophonesoutsidethecoverageofyourfrontofhousespeakerstoreducetheriskoffeedback.

SPEAKER PLACEMENT

Titan™ Series

8

Titan™ REAR PANEL LAYOUT

CONNECTION DIAGRAM #1

Titantwochannelsetup


9

CONNECTION DIAGRAM # 2

Titanmono frontofhouse+stagemonitorsetup

NOTE: This configuration represents a 4 ohm load to each output channel of the amplifier

Titan™ Series


USING THE Titan WITH A PASSIVE SUBWOOFER


USING THE Titan™ 8/12/15 IN A BI-AMP SYSTEM

10


Titan™ 8A MKII / Titan™ 12D / Titan™ 15D

The Loop / Mix Switch

The LOOP/MIX switch allows you to control the signal content going to the XLR OUTPUT jack. In the “LOOP”

mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the EQ section

and volume control. When in the MIX mode, this switch routes the combined (or “mixed”) signals of both INPUT

A and INPUT B to the line level XLR OUTPUT jack. This signal can then be sent to additional powered speakers

orpoweredsubwoofers.

8A MKII - REAR PANEL FEATURES

11

Titan™ Series

Titan™ 12D/15D REAR PANEL LAYOUT

12

1

2

78

12

3

5

9

1110

6

13

14

4


TITAN™ 8A MKII/12D/15D REAR PANEL FEATURES1. Heat Sink: The heat sink allows for dissipation of heat built up from the amplifier via air cooling at the rear

of the enclosure. (Titan 8A MKII and 15D only)

2.VOLUME for INPUT A and INPUT B:Theseknobscontrolthelevelofeachinputchannel(Controlsthemaster volume on the Titan 8A MKII)

3.HI and LOW EQ (equalization) controls:Theseknobscontrol theequalizationof theoveralloutputsignal providing +/- 10dB of gain for each band.

4.Remote Control:ThisPheonixconnectorcanbeusedtocontrolthevolumewithanappliedvoltage.

5.90Hz Monitor Filter switch:Usedtoreducebassbuildupduetohalfspaceloading.

6.Horn LED defeat switch: Switches off the horn power LED for discrete applications.

7.RCA L / R (Left and Right) input jacks: These jacks allow input of a stereo signal (left and right). The signal is actively combined or “summed” providing a mono signal to the amplifier.

8.GAIN selection switch:Thisswitchselects thepropergainstructure for INPUTA. Ifamicrophone isconnected to INPUT A, use mic mode (up). If the signal source is anything other than a microphone (playback

device, keyboard or mixer output, for instance) use the line mode (down) .

9&10.POWER ON / OFF switch, POWER ´ON´ indicator LED and LIMIT indicator LED:Theswitch: turns the power on and off. The bracketed LED to the left of the POWER switch illuminates when the

power switch is in the´ON´ position. The LIMIT LED illuminates when the signal limiter is limiting the level of

thesignaltopreventdistortionandoverload.

11.Output source “LOOP / MIX” switch: In the “LOOP” mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the EQ section and volume control. When in the MIX mode, this

switch routes the combined (or “mixed”) signals of both INPUT A and INPUT B to the line level XLR OUTPUT

jack.

12.XLR / ¼” COMBO input jacks for INPUT A and INPUT B: These convenient jacks allow XLR or ¼” balanced input connections to INPUT A and INPUT B

13.POWER cord receptacle:ThisisareceptacleforastandardIEC,threeprong,groundedACelectricalconnection cord. Be sure that you are plugging into the correct source voltage that matches what is indicated

justbelowthepowercordjack.

14.XLR line level OUTPUT jack:ThisjackprovidesabalancedlineleveloutputforconnectiontoadditionalTitan™ ACTIVES, powered subwoofers or amplifiers.

13

Titan™ Series

Titan™12D / 15D CONNECTION DIAGRAM # 1

Basic microphone / playback hookup

Titan™12D / 15D CONNECTION DIAGRAM # 2

Connecting two Titan™ ACTIVE speakers together

14


TITAN™ SUB A12 REAR PANEL FEATURES

1. HEAT SINK

2. VOLUME CONTROL

3. INPUT L

4. INPUT R

5. OUTPUT R

6. OUTPUT L

7. POWER SOCKET

8. LIMIT LED

POWER LED

9. POWER SWITCH

10. PHASE SWITCH

11. CROSSOVER

FREQUENCY

CONTROL

Cooling fins for amplifier. Do not obstruct.

Adjuststhevolume.

Balanced line level input via a XLR/ ¼” combo connector.

Balanced line level input via a XLR/ ¼” combo connector.

Balanced male XLR connector provides output HIGHPASS signal.

Balanced male XLR connector provides output HIGHPASS signal.

ThisistheconnectionfortheIECACpowerconnector.

LED indicator illuminates when the signal limiting function is activated.

LED indicator illuminates when the unit is powered up.

Turns the power on and off to the subwoofer amplifier module.

Selects the polarity of the signal being sent to the subwoofer.

0°selectsthesignalpolarityasitappearsattheinput.

The180°selectioninvertsthepolarityofthesignal.

Adjustable80Hz/100Hz/120Hz/150Hz/180Hz/200Hz.

15

Titan™ Series

Titan™ Sub-A12 CONNECTION DIAGRAM # 1

TWO CHANNEL SYSTEM WITH HIGHPASS OUTPUT

16



USING TWO Titan™ Sub-A12 WITH

TWO POWER SPEAKERS

17

Titan™ Series

Titan™ Sub-A15 - REAR PANEL FEATURES

1. INPUT A - Balanced line level input via a XLR / ¼” combo connection.

2. OUTPUT A - Balanced male XLR connection provides “THRU” or HIGHPASS signal (depending on switch setting).

3. SPEAKER LEVEL INPUT - Allows for connection of an external amplifier to use the Titan™ Sub-A15 as a passivesubwoofer.

NOTE: Disconnect the power cord when using the Titan™ Sub-A15 in this mode.

4. INPUT B - Balanced line level input via a XLR / ¼” combo connection.

5. OUTPUT B - Balanced male XLR connection provides output “THRU” or HIGHPASS signal (depending on switch setting).

6. HEATSINK - Cooling fins for amplifier. Do not obstruct.

7. VOLUME CONTROL-Adjustsvolumelevelofthesubwoofer.

8. THRU / HIGHPASS SWITCH - Selects the signal type that is routed to the OUTPUT jacks, “THRU” sends the unprocessed signal to the outputs. “HIGHPASS” filters the signal at 100Hz to the outputs.

9. PHASE SWITCH - Selects the polarity of the signal being sent to the subwoofer. 0° selects the signal polarity asitappearsattheinput.The“180°”selectioninvertsthephaseofthesignal.

10.LIMIT LED - LED indicator illuminates when the singal limiting function is activated.

11. POWER LED - LED indicator illuminates when the unit is powered up.

12.POWER SOCKET-ThisistheconnectionfortheIECACpowerconnector.

13.POWER SWITCH - Turns the power on and off to the subwoofer amplifier module.

VOLUME

CAUTIONRISK O F ELECTR IC SHO CK

D O N O T O PE N !AVIS: RISQUE DE CHOC ELECTRIQUE -NE PAS OUVRIR

WARNING: SHOCK HAZARD DO NOT OPEN

PHASE

THRU 0°

180°(100Hz)HIGHPASS

N 2082

ON

OFF(B A L A N C ED ) (B A L A N C ED )

INPUT

INPUT

OUTPUT

OUTPUT(B A L A N C E D )(B A L A N C E D )

A

B

SPEAKERLEVEL IN

0

MAX8 II

I I

I I

I

I

I

I

WWW.WHARFEDALEPRO.COM

POWER AC 220-240V~50Hz 400WFUSE T4AL250V

SERIALNUMBER

OUTPUT A

OUTPUT B

SPEAKERLEVEL INPUT

INPUT A

HEATSINK

PHASE SWITCH

LIMIT LED

POWER LED

POWER SOCKET

POWER SWITCH

VOLUMECONTROL

THRU/HIGHPASSSWITCH

INPUT B

1

234

5

6

7

891011

LIMIT

1213

_

18



TWO CHANNEL SYSTEM WITH HIGHPASS OUTPUT

NOTE: This same connection configuration can be used with OUTPUT A and B used in a full-

range mode when the THRU/HIGHPASS switch is in the "THRU" (up) position.

19

Titan™ Series


USING TWO Titan™ Sub-A15's WITH

TWO POWERED SPEAKERS

20


SPECIFICATIONS - Titan™ PASSIVE SERIES

Loudspeaker Type:

Frequency Response (+/–3dB):

Sensitivity (1W@1M):

Peak SPL:

HF Coverage (H x V):

System Impedance:

POWER (WATTS)

Continuous:

Music:

Peak:

LF DRIVER

Size:

Coil Size:

HF DRIVER/ HORN

Coil Size:

Exit Size:

Diaphragm Material:

HF Driver Protection:

Long-Throw EQ Compensation:

Horn Type:

Throat Size:

CROSSOVER

Type/Frequency/Filter:

ENCLOSURE

Shape/ Material:

Rigging:

COLOURS

OUTPUT CONNECTORS

DIMENSIONS/WEIGHTS

Weight:

Dimensions (H x W x D):

Titan™ 8

8" 2-way

70 - 20kHz

96dB

124dB

90˚ x 60˚

8 ohm

150W

300W

600W

203mm/ 8"

38.86mm / 1.53"

Compression Driver

25mm/1"

30mm/1.2"

Cloth

Bulb

N/A

EWG™ - Elliptical Waveguide

25mm/1"

2-way 2.4KHz / Linkwitz-Riley

Trapezoidal/ Polypropylene

(8) M6 threaded rigging points

+ (4) M6 threaded rigging points

on bottom in Omnimount®

30.0-type footprint + Speaker pole-

mount receptacle with lock screw

+ 1 built-in carry handle + Optional

wall-mount bracket + (Optional

dual-unit array speaker stand

hardware)

Grey or Black or White

2 x 1/4" jacks + 2 x NL4

5.5kg / 12.1lbs

396 x 266 x 221mm/

15.59" x 10.47" x 8.7"

Titan™ 12

12" 2-way

55 - 20kHz

98dB

128dB

90˚ x 60˚

8 ohm

250W

500

1000

305mm/ 12"

64.26mm / 2.5"

Compression Driver

44mm/1.75"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

3dB boost (long-throw) / Flat

(near-�eld)

EWG™ - Elliptical Waveguide EWG™ - Elliptical Waveguide

25mm/1"






60.0-type footprint + Speaker

pole-mount receptacle with lock

screw + Optional wall-mount

bracket + (Optional dual-unit

array speaker stand hardware)


2 x 1/4" jacks + 2 x NL4

12kg / 26.4lbs

556 x 384 x 312mm/

21.88" x 15.1" x 12.3"

Titan™ 15

15" 2-way

50 - 20kHz

97dB

129dB

90˚ x 60˚

8 ohm

400W

800W

1600W

381mm/ 15"

75mm / 3.0"

Compression Driver

51mm/ 2.0"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

N/A

25mm/1"






60.0-type footprint + Speaker

pole-mount receptacle with lock

screw + Optional wall-mount

bracket + (Optional dual unit

array speaker stand hardware)


2 x 1/4" jacks + 2 x NL4

22kg / 48.4lbs

708.3 x 477.8 x 401.77mm/

27.9" x 18.8" x 15.8

21

Titan™ Series

SPECIFICATIONS - Titan™ ACTIVE SERIES

System Type

Frequency Response (+/-3dB)

Low Frequency Driver (mm/in.)

High Frequency Driver

Exit Size (mm / inches)

Dispersion (H x V)

Amplifiers

Low Frequency (Class D)

High Frequency (Class D)

Electronic Crossover:

Crossover Frequency

Equalization:

Subsonic Filter

Amplifier Protection

Power On

Thermal

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Titan™ 8 ACTIVE MK II

70-20kHz

205mm / 8”

Compression Driver

90° x 60°

2.4kHz

30Hz, Second -order filter

Power switch on / off mute

Amplifier shutdown, auto reset

Independent LF and HF limiters

Yes

Yes

Red LED

Green LED

Titan™ 12 D

Active 12” 2-way Bi -Amplified

55-20kHz

305mm / 12”

Titanium Compression Driver

25mm / 1"

90° x 60°

24dB/octave Linkwitz-Riley

2.3kHz

High (±10dB) 10kHz Shelving

Low (±5dB) 100Hz Shelving




60% Nominal line voltage


Yes

Yes

Turns on approx 250W output

Red LED

Green LED

Titan™ 15 D

Active 15” 2-way Bi -Amplified

50-20kHz

381mm / 15”

Titanium Compression Driver

25mm / 1"

90° x 60°

24dB/octave Linkwitz-Riley

1.8kHz








Yes

Yes


Red LED

Green LED

Active 8” 2-way Bi-Amplified

30mm / 1.2”

Rated 150W continuous, 300W Peak

Rated 30W continuous, 60W Peak

24dB per octave Linkwitz-Riley


< 80VAC


Rated 250W continuous, 500W Peak Rated 350W continuous, 700W Peak

Rated 50W continuous, 100W Peak Rated 70W continuous, 140W Peak


22


SPECIFICATIONS - Titan™ ACTIVE (Con't)

Inputs

Input A – type

Input Sensitivity

Maximum Input Level

Input Connector

Input Impedance

Maximum Input Level

Input B – type

Input Sensitivity

Maximum Input Level

Input Connectors

Line Output

Impedance:

Sensitivity

AC Power details

Power Supply

AC Power Options

Power On Indicator

Rigging / Bracket / Mounting

Options

Enclosure Material

Colours

Dimensions H x W x D (mm)

Dimensions H x W x D (in)

Net Weight (kg / lbs)

Gross Weight (kg / lbs)

Titan™ 8 ACTIVE

Switchable balanced mic or line

level input

+22dBu

XLR - 1/4” Combo jack

+22dBu

High Efficiency Switching Mode

Power Supply

Green LED Green LED Green LED

8 M6 threaded inserts including 4

M6 threaded

inserts on bottom in OmniMount

30.0-type footprint

Pole-mount receptacle with lock

screw

1 carry handles

Optional wall-mount bracket

Injection Moulded Polypropylene

Grey or white or black

396 x 266 x 221

15.6 x 10.5 x 8.7

Titan™ 12 D


level input

Mic: -40dBu (-42.2dBv or

7.75mVrms)

+22dBu


+22dBu

Line level input

XLR - 1/4” Combo jack: 0dBu (-2.2

dBv or 0.775Vrms)

XLR - 1/4” Combo jack: 0dBu (-2.2

dBv or 0.775Vrms)

RCA: 0dBu (-2.2dBv or

0.775Vrms)

+22dBu

Combo ja ck: 1 / 4" - XLR / Summe d

dual RCA jacksSwitchable LOOP / MIX Balanced

Male XLR

Balanced: 200 ohm Unbalanced:

100 ohm


Power Supply

AC100~120V / 220~240 V, 50 /

60Hz

10 M8 threaded inserts including

4 M8 threaded


60.0-type footprint


screw

2 carry handles (one on each

side)



Black

556 x 384 x 312

21.9 x 15.1 x 12.3

12.4kg / 27.28lbs

15.5kg / 34.lbs

Titan™ 15 D


level input


7.75mVrms)

+22dBu


+22dBu

Line level input

RCA: 0dBu (-2.2dBv or

0.775Vrms)

+22dBu

Combo jack: 1/4" - XLR /

Summed dual RCA jacksSwitchable LOOP / MIX Balanced

Male XLR

Balanced: 200 ohm Unbalanced:

100 ohm


Power Supply

AC100~120V / 220~240 V, 50 /

60Hz

10 M8 threaded inserts including

4 M8 threaded


60.0-type footprint


screw

2 carry handles (one on each

side)



Black

708.3 x 477.8 x 401.8

27.9" x 18.8" x 15.8

22.9kg / 50.38lbs

27.7kg / 60.94lbs


3.4mVrms)

Line: 0dBu (-2.2dBv or 0.775Vrms)

Balanced: 20kΩ -

Unbalanced: 10kΩ

Balanced: 10kΩ -

Unbalanced: 5kΩ

Balanced: 10kΩ -

Unbalanced: 5kΩ

+22dBu

Combo jack: 1/4" - XLR

0dBu (-2.2dBv or 0.775Vrms) 0dBu (-2.2dBv or 0.775Vrms) 0dBu (-2.2dBv or 0.775Vrms)

AC100~240V, 50 / 60Hz

6.25kg / 13.75lbs

8.15kg/ 17.93lbs

Switchable LOOP / MIX

Balanced Male XLR Connector

N/A

N/A

Balanced: 1k ohm Unbalanced:

500 ohm

MKII

Line: 0dBu (-2.2dBv or 0.775Vrms) Line: 0dBu (-2.2dBv or 0.775Vrms)

23

Titan™ Series

SPECIFICATIONS - Titan™ SUB SERIES

System Type

Frequency Response (+/-3dB)

Enclosure Material

Enclosure Colour

Frame material

Size (mm / inches)

Coil Size (mm / inches)

Impedance

Speaker Pole Adapter

Inputs A & B - Type / Connection

Output A & B Type / Connection

Input Sensitivity

High Pass Frequency Selection

Phase Switch Selection

Crossover Frequency (HZ)

Speaker Level Input Impedance

Speaker Level Input Connection

Amplifier Power: Continuous

Amplifier Power: Peak

Power On Indicator

Power On Protection

Thermal Protection

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Dimensions H x W x D: (mm)

Dimensions H x W x D (in)

Weight (Net) kg / lbs

TITAN™ Sub-A15

Band-pass subwoofer

45-150Hz

18mm Plywood

Grey or Black

Die-cast aluminium frame

404mm / 15”

75 / 3”

4 ohm

Yes

Balanced Line Level inputs via two

combo connectors

Balanced Line Level inputs via two

combo connectors

0.56V

100Hz

0° / 180°

150

1/4” TS Phone input

4Ω

400W

600W

LED

Power switch on / o� mute

Ampli�er shutdown, auto reset


Independent LF limiters

Yes

Yes


Red LED

Blue LED

630.0 x 478.0 x 640.0

24.8 x 18.8 x 25.2

45.48kg / 100.0lbs

Titan™ Sub-A12

Re�ex subwoofer

55-200Hz

15mm MDF

Grey or Black

steel frame

305mm / 12”

64.26mm / 2.5”

4 ohm

Yes

Balanced Line Level inputs via

two combo connectors

Balanced Line Level inputs via

two combo connectors

0.37V

150Hz

0° / 180°

80/ 100/ 120/ 150/ 180/ 200

(adjustable)

250W

500W

LED

Power switch on / o� mute

Ampli�er shutdown, auto reset


Independent LF limiters

Yes

Yes


Red LED

Blue LED

360.0 x 493 x 431.0

14.2 x 19.4 x 16.9

22.31kg /49.0lbs

24


DIMENSIONS

25

Titan™ Series

DIMENSIONS

26


DIMENSIONS

27

12.28"312mm

21.88"556mm

15.11"384mm

12.28"312mm

7.1"180mm

15.83”402mm

27.87”708mm

18.81”478mm

15.83”402mm

Titan™ Series

DIMENSIONS

28


WharfedaleProproductsarewarrantedofmanufacturingormaterialdefectsforaperiodofoneyearfromtheoriginaldateofpurchase.Intheeventofmalfunction,contactyourauthorizedWharfedaleProdealerordistributorforinformation.

*Be aware that warranty details may differ from country to country. Contact your dealers or distributor for information.Thesetermsdonotinfringeyourstatutoryrights.

WHARFEDALE PRO LIMITED WARRANTY

29

WharfedaleProfessionalIAG HOUSE, Sovereign Court, Ermine Business Park Huntingdon, Cambs, PE29 6XU, England

www.wharfedalepro.comWharfedale Professional reserves the right to alter or improve specifications without notice.

All rights reserved © 2010 Wharfedale Pro. Wharfedale Pro is a member of the International Audio Group (IAG).

Documents

OPERATING MANUAL AND USER GUIDEOPERATING MANUAL AND USER GUIDE 1 IMPORTANT WARNINGS & SAFETY INSTRUCTIONS 1. Read these instructions 2. Follow all instructions 3. Keep these instructions